ANDY'S CARB CLEANING GUIDE - REV 1.DOC APRIL 04, 2012

Size: px
Start display at page:

Download "ANDY'S CARB CLEANING GUIDE - REV 1.DOC APRIL 04, 2012"

Transcription

1 ANDY'S CARB CLEANING GUIDE - REV 1.DOC APRIL 04, 2012 L:\000 - Files\Motorcycle\1984 V45 Magna\Carbs\Andy's Carb Cleaning Guide - Rev 1.doc Page 1 of 7

2 Don t worry about the lost first page it is a BS computer glitch so I inserted a blank one to be lost the article starts here: Carburetor Cleaning Guide (Revision 1 May 2013) Carb cleaning just the phrase alone is enough to make a V4 owner blanch and break into a cold sweat but it doesn t have to be. Any DIYer who understands why a wrench isn t for use as a hammer and what the difference is between a screwdriver and a pry bar can successfully clean their own carbs with care and attention to detail. Some inexpensive tools and supplies are need but beyond that there is a fairly simple recipe to be followed and a few basic precautions to be observed. Carbs function as part of the entire combustion system and interact closely with the other parts of the system. To get the best performance from your bike, carb cleaning needs to be part of an overall tune-up process. To minimize the amount of time it will take to get your bike into good running order it is necessary to do each step in order to establish the correct conditions for the next step. Doing the steps out of order will not produce the same results because of the interaction between the parts of the system. I encourage you to take pictures of each step to serve as a reference when it is time to re-assemble the components. This is especially useful for cable routing and linkage connection reference. I have inserted an icon where I think a picture may be helpful. This guideline is based on my 1985 V45 Magna but is general enough to be widely applicable. I have inserted an icon where I think models typically vary. Whenever you take your carbs apart check that the front and rear carbs have the right parts in the right places. In the past I have recommended doing one carb at a time so as not to mix the parts no longer since it occurred to me that there is no guarantee that some skeezix shop or previous owner did not mix them up already. You need to actively determine if they are in the right carbs, not just assume that putting them back where they were is right. Things you need to know before cleaning your Carbs (differences between the carbs) Before cleaning or rebuilding your carbs you should be aware that there are similar looking parts in different carbs that have easy to overlook but critical differences. Whenever you take your carbs apart check that the front and rear carbs have the right parts in the right places. In the past I have recommended doing one carb at a time so as not to mix the parts no longer since it occurred to me that there is no guarantee that some skeezix shop or previous owner did not mix them up already. The smaller jets, thicker needles, and larger springs go up front, the larger jets, thinner needles, and smaller springs go in the rear. This acts to run the rear carbs with a slightly richer mixture to use fuel cooling to compensate for a reduced airflow cooling of the rear bank of cylinders. Page 2 of 7

3 The emulsion tubes with the holes furthest from the threads go into the rear, the emulsion tubes with the holes closest to the threads go in the front. This is due to the different mounting angle of the carbs. The needles are designated by 3 letters - the 3 letters represent taper, length and diameter. The higher the letters, the bigger the needle s size. The jets are designated by 2 or 3 numbers - 42 = 0.42mm diameter, 128 = 1.28mm etc. Carbs are clean when they are clean where you cannot see, not when they are clean where you can see - then they are just pretty. The Carb Cleaning Recipe The tune-up steps: 1. Before removing carbs; a. lift gas tank (make sure not more than 2/3 full), b. remove air filter, filter box, metal screen under box, c. drain and remove the radiator, d. remove heat shield mounted on the air box on the radiator side, e. turn the fuel petcock off, f. remove the gas line from carb #1 and catch gas in a container. 2. Removing carbs; a. note orientation of the isolator (rubber boots) clamps and loosen all 8 of them, b. pull the carbs and airbox upwards until loose (difficult by hand - try ONE tie down threaded under the airbox and over the top of the frame or anchored to the handlebars accompanied by hand pressure back and forth on each side) until the carbs come loose as a single unit, c. remove the isolators and clamps, d. wiggle, tilt, and the slide carbs to the left side of the bike, e. note the cable routing and disconnect the choke and two throttle cables, f. undo the single clamp bolt (8mm) holding each of the two coolant crossover tubes, g. work each tube straight out of the heads. With the clamp removed they are only held by the o-rings on each end. If you pry them be gentle they are thin walled, and pry each end equally so they don t twist and jam. If they jam, gently push the out end back in level with the other and then continue. Don t be rough if you distort the ends you will have trouble getting a leakfree re-installation, h. remove the carbs out the right side of the bike. Some twisting and tipping may be needed but force isn t necessary unless you are doing something wrong, i. with carbs off the bike, drain any remaining gas from them. 3. Before disassembling the carb-airbox unit; a. Note which carb is which carb number. The carb for cylinder #1 is carb #1. On my bike Cylinder #1 is rear left, #2 is front left, #3 is Page 3 of 7

4 rear right, #4 is front right. b. Prepare a container for each carb and the pieces removed from that carb a plastic tray is excellent but a separate area on the workbench is sufficient. Do not mix the parts between the carbs as there are subtle but critical differences (see previous section). Label each container with the carb number. c. Prepare an additional common container for linkages and other external parts, d. Note which carb number fits where in the airbox. If you want, use a marker to label the inside of the airbox. 4. Disassembling the carb-airbox unit; a. Start by removing the 2 screws (Phillips #1) per carb from the inside of the airbox. If you use an impact driver be careful not to damage the thin wall casted body of the airbox, b. Separate the carbs as a group from the air box and lay them on the bench, c. Remove each of the rubber trumpets and place it in the appropriate carb s container, d. Carefully note how all the linkages and connecting tubes run. Pictures are a definite plus here. Consider using paint marker dots to identify which end or face is oriented where if this is your first time taking them apart. e. Disconnect all the linkages and connecting tubes, placing the springs, washers, nuts, etc. into the common container. f. At this point, I like to use a 1/8 drill bit to mark the carb number on each carb body by drilling a slight dimple pattern in the carb body as shown at right. Be sure that you do not drill into any passageway or you will ruin the carb body. The location shown is a safe one. 5. Disassembling each carb; a. Slider - Remove the 3 Phillips screws from the domed chrome top hold the top in place against a light spring pressure while removing the screws. Before moving the top, look carefully around the edge and note where the little raised channel is located. b. Lift the top off, remove the coil spring and place both in the container, c. The black rubber diaphragm is delicate and EXPENSIVE treat it with care while removing it along with the slide and main jet. Put the carb down and hold onto the slide, Page 4 of 7

5 d. Remove the needle from the slider by pressing down on the plastic piece inside the bottom of the slider and turning it 90 degrees. It should now lift out, releasing the needle. Make a special note of any washers under the head of the needle and remove them with the needle, e. Place the slide with diaphragm in a protected place a dedicated margarine container within the carb container would not be going overboard. f. Float bowl - Turn the carb over and remove the 4 screws holding the bowl. The bowl will likely be stuck in place, very gently pry it apart taking care not to damage the mating surfaces or the float bowl gasket. Inspect the gasket, if it damaged or flattened so that it does not protrude above the mating face of the float bowl, it needs to be replaced, g. Note the orientation of the float and use needle-nose pliers to pull the float pivot pin completely out, removing it and the float, h. Remove the float valve, screen, and washer from the carb body under where the brass tang of the float sat, i. Remove the main jet (slot head), main jet holder (hex body), and the slow jet from the carb body. One piece is pressed in and is not removable, j. Choke Remove the nut and washer from the top of the activating shaft for the choke. Pull the black plastic tube up and off the shaft, loosening the lower portion of the shaft. Unscrew the plastic nut around the choke plunger rod and work the shaft forks out of the groove on the end of the plunger. Remove the activating shaft, plastic nut, and plunger. Hopefully yours will not have the woodscrew added by a creative PO to replace the brass nub on the end of the enrichner valve likely broken off during an incorrect disassembly attempt. k. Butterfly valve Note the location of any markings on the round butterfly valve it has a top-bottom and insideoutside orientation that must be maintained when it is reassembled or it will not fit or operate correctly. The valve is secured to the throttle shaft by two small Phillips head screws. It is essential to have a #3 Phillips screwdriver that fits the screw heads tightly or they will be stripped when you try to remove them. The other end of the screws has been slotted and spread apart slightly to ensure they do not vibrate out of the throttle shaft. Remove the screws, l. Turn the throttle shaft 90 degrees and pull the butterfly valve out, m. The throttle shaft is now free to be removed, n. Around where the throttle shaft enters the carb body there is a pressed in metal ring covering a felt seal. Use a small screwdriver to remove the ring and washer without damaging either of them. The seal Page 5 of 7

6 can be damaged by the cleaners and is no longer available as an OEM part possibly not as an aftermarket part either, o. Pilot needle jet The pilot jet screws into the outside of the throat of the carb near where the isolator (rubber mounting boot) stops. It may be covered by a thin aluminum plug pressed into the hole over the pilot jet or more likely, that may have been removed during a previous cleaning. If the plug is there, remove it by drilling a small hole through it and inserting a dental pick or wood screw and pulling the cap out. Discard it. p. Under the cap is the jet. Use a small slot screwdriver to screw the jet IN until it bottoms gently, counting the turns to the nearest 1/8 th turn. Record the number of turns for use later they can be different for each carb so do not mix them up, q. Unscrew the jet and remove it along with the spring, washer, and o-ring. If the washer and o-ring do not come out it is necessary to hook them and pull them out with a small piece of copper wire or other soft hook that will not damage the seat. r. If you haven t done it already, now is a good time to order any replacement parts you need. (The screws for the float bowls and diaphragm housings are size M4x0.70 pitch. length is about 1 inch for float bowls and.75 inch for diaphragm. Do not use longer screws as those for the carb bowl will hit and crack the plastic fuel transfer tubes. Carb mounting screws are M5x1 about 1 inch long.) s. Record the numbers stamped on the jets and valves along with the carb number they were found in. This information is for future use such as determining if you need to re-jet after changing air filter or muffler type or for diagnostics when having carb problems. 6. Cleaning each carb; Washer and o-ring are still in here and must be fished out Ultrasonic cleaners are excellent for cleaning carbs but are usually to expensive for a DIYer to acquire for occasional use. The next best way for a DIYer to clean carbs is to buy a gallon of carb cleaner and be ready to soak the metal parts in it using a basket or strainer. Spray carb cleaners are useful for cleaning the inside of small passageways in the carb after it has been soaked. Carbs must be disassembled for cleaning. Never put carb cleaner directly onto rubber, plastic, or felt carb parts as they can be damaged and ruined by it. They can also be damaged by spray carb cleaners. Soak all the metal parts for one carb together for 8-24 hours then rinse them with water and dry with compressed air. When doing this, take appropriate precautions to avoid blowing them into Alice s rabbit hole where they will live forever. Use spray carb cleaner to blow through each passageway make sure that it emerges somewhere and that the passageway is clear. Page 6 of 7

7 7. Before installing carbs a. make sure the fuel filter is clear and the tank(s) do not contain rust or sediment (so you don't have to clean the carbs again in 2 weeks), b. make sure that the valve clearances are correct (so each cylinder can breathe freely and evenly), c. bench synch the carbs (to get air flow thru carbs roughly equalized), d. set pilot screws about 2-1/2 turns out on each carb (to get mixture roughly right), 8. After installing carbs a. make sure the air filter is correctly installed and is clean (to allow correct air flow to the carbs), b. on-bike carb synch (to finely balance the air flow across the carbs), c. adjust pilot screw on each carb using the idle-drop method (to match fuel volume to the air flow volume), d. make sure that the hand grips are secure (you will need to HANG ON!). Magna carb mounting boots (isolators): The V65 is 36mm (1.42") and the V45 is 32mm (1.25") You can get fuel filler neck hose in both sizes and the ultimate is 1.5" or 1.25" silicon hose. If you are having trouble finding the hose, one possible source for this hose is a local farm equipment dealership. Do not get the hose with the wire reinforcing or installing your carbs will be a special kind of challenge! These should be done in the order listed and do not skip any steps. There is no such thing as a shortcut when cleaning carbs - they just lead to do-overs! Example: if you skip step #2 and the valve clearances are off, then the on-bike synch will not be correct, so then the mixture setting will be off,so... do-over. Happy in Hondaland, MagnAndy Brampton, Ontario, Canada When one removes the o-ring gasket, there may be a few noticeable traces of something that the factory used to keep the gasket in place while positioning the bowl. I usually do not need to use any gasket sealer material to hold the o-rings in place even for the non-preformed ones but if necessary, I use a TINY dab of silicone in a few places, to hold the gasket in place in the bowl cover groove. It works like a charm. Just make sure your dab is very little, and dabbed toward the outside of the bowl groove. Do not get much, if any on the inside of the gasket or housing, because fuel will dissolve it and cause problems when it gets into the bowl/jets. That was my mistake on the first carb pull. Page 7 of 7

Adjusting Carbs For Re-Jetting (Procedure written for an Intruder 1500 LC) NEWLY UPDATED: APRIL 2003

Adjusting Carbs For Re-Jetting (Procedure written for an Intruder 1500 LC) NEWLY UPDATED: APRIL 2003 SECTION ONE: Get Prepared - Tools Adjusting Carbs For Re-Jetting (Procedure written for an Intruder 1500 LC) NEWLY UPDATED: APRIL 2003 Courtesy of: Half-Crazy Get a manual impact driver (the kind you hit

More information

Mikuni RS Carburetor Conversion

Mikuni RS Carburetor Conversion Mikuni RS Carburetor Conversion After putting your carbies on the bench or the kitchen table if the wife is out, you will see that the linkages may be in different positions depending on which brand of

More information

SECTION 4 - FUEL SYSTEMS AND CARBURETION

SECTION 4 - FUEL SYSTEMS AND CARBURETION SECTION - FUEL SYSTEMS AND CARBURETION FUEL SYSTEMS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -62 FUEL PUMP - - - - - - -

More information

INSTALLATION GUIDE CRF150R Manual Revision:

INSTALLATION GUIDE CRF150R Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE CRF150R 191-810 Manual Revision: 032508 2002 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise, Idaho 83714 208-426-0659

More information

VM Carb Rebuild Paul Musser October 2005 v1.0

VM Carb Rebuild Paul Musser October 2005 v1.0 VM Carb Rebuild Paul Musser October 2005 v1.0 A big thank you to all the folks at GS Resources (www.thegsresources.com) for their invaluable assistance. Much of the information for his document came from

More information

BA /02/03/04/06/07/08/13/13B/15 BIG AIR KIT (BAK) - Yamaha Road Star (99-07)

BA /02/03/04/06/07/08/13/13B/15 BIG AIR KIT (BAK) - Yamaha Road Star (99-07) BA-2020-00/02/03/04/06/07/08/13/13B/15 BIG AIR KIT (BAK) - Yamaha Road Star (99-07) Page: 1 Revision: 6.2-02/23/2011 Install Time: 1.5 Hours We recommend a qualified Yamaha technician install this kit

More information

Fuel Pump & Sending Unit Repair

Fuel Pump & Sending Unit Repair If your C4 s fuel gauge reads full regardless of how much fuel you actually have, the sending unit in the tank is most likely at fault. If you have priced a new sending unit, you realize that they run

More information

~. a~' ~ ( I o~~~ 4-0. ~Sj~' AO~ i/~ CB1000C (ij)aon'da in-ib) ~ "" ~ ~!~~P. ~ J N m (6-12 kg-em,

~. a~' ~ ( I o~~~ 4-0. ~Sj~' AO~ i/~ CB1000C (ij)aon'da in-ib) ~  ~ ~!~~P. ~ J N m (6-12 kg-em, e V ~. a~' ~ I ~ J C t \"" 8.0- ( I o~~~ ~ "" ~ ~. ~!~~P. C8 0 & 0,-t. ~ CB1000C (ij)aon'da 0.6-1.2 N m (6-12 kg-em, 5-10 in-ib) 4-0 / 4.0-6.0 N m (40-60 kg-em, 35-52 in-i b) t$ "'07~ / c;:::/ j ~Sj~'

More information

KEIHIN CARBURATORS FOR 4-CYLINDER HONDA MOTORCYCLES

KEIHIN CARBURATORS FOR 4-CYLINDER HONDA MOTORCYCLES KEIHIN CARBURATORS FOR 4-CYLINDER HONDA MOTORCYCLES Set of 4 Keihin carburetors marked 089A and used on 1976 CB550K GENERAL NOTES: All carburetors perform the same function: mixing air and fuel for supply

More information

Днепр) Russian Motorcycle Carburetors Part 2B: PZ-24 and PZ-28 Carburetor Assembly and Jet Drilling

Днепр) Russian Motorcycle Carburetors Part 2B: PZ-24 and PZ-28 Carburetor Assembly and Jet Drilling Ural (Урал( Урал) - Dnepr (Днепр( Днепр) Russian Motorcycle Carburetors Part 2B: PZ-24 and PZ-28 Carburetor Assembly and Jet Drilling (applies also to K-37 K and K-38 K carbs) Ernie Franke eafranke@tampabay.rr.com

More information

Prerequisites: Shop Manual (recommended) pages 3-9 through 3-13.

Prerequisites: Shop Manual (recommended) pages 3-9 through 3-13. Prerequisites: Order your gaskets average about $25.00 bucks X 2 so $50.00 4NK-11193-00-00 Obtain a shim kit (Should have several 265 and 270s) (Some dealers will exchange) Obtain a Valve Bucket Tool YM-33961

More information

Jetting and understanding your CV carburetor

Jetting and understanding your CV carburetor Jetting and understanding your CV carburetor What do all these pieces do? You may also ask, how or why would I do this to my carb? The goal of this article is to unravel the mystery of carburetor jetting

More information

235/245400, , 28N

235/245400, , 28N Models 235/245400, 287000, 28N thru W, 310/312/313700 These carburetors have a fixed high speed main jet with adjustable idle, Fig 183. The different carburetors are identified as LMT 1 and up. The letters

More information

CARTER DOWNDRAFT CARBURETOR Terraplane All Models. Technical Information

CARTER DOWNDRAFT CARBURETOR Terraplane All Models. Technical Information CARTER DOWNDRAFT CARBURETOR 1934 Terraplane All Models Technical Information . Carter W-1 Downdraft Carburetors 1934 Terraplane Challenger, Model KS NOTE: Terraplane Models. Carburetor fitted with Anti-

More information

Slave Cylinder Weep Hole Drilling Procedure

Slave Cylinder Weep Hole Drilling Procedure Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key

More information

INSTALLATION GUIDE. Kawasaki KLR Manual Revision:

INSTALLATION GUIDE. Kawasaki KLR Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE Kawasaki KLR650 191-640 Manual Revision: 030308 2007 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise, Idaho 83714

More information

SECTION 4 - FUEL/LUBRICATION/COOLING

SECTION 4 - FUEL/LUBRICATION/COOLING For Arctic Cat Discount Parts Call 606-678-9623 or 606-561-4983 SECTION 4 - FUEL/LUBRICATION/COOLING 4 TABLE OF CONTENTS Carburetor Specifications... 4-2 Carburetor Schematic... 4-2 Carburetor... 4-3 Cleaning

More information

ZAMA CUBE CARBURETOR DISASSEMBLY AND SERVICE

ZAMA CUBE CARBURETOR DISASSEMBLY AND SERVICE ZAMA CUBE CARBURETOR DISASSEMBLY AND SERVICE MIXTURE SCREWS Remove idle and main mix ture screw. Inspect each screw for damage, especially the needle points which should have no deformation of the tapered

More information

Remove Air Cleaner Cover and. Filter

Remove Air Cleaner Cover and. Filter Remove Air Cleaner Cover and Inspect paper filter for tears Foam pre-cleaner is washable if equipped Replace if necessary Filter Remove Trim Panel Pull throttle lever knob off Remove 3, 8mm screws Remove

More information

INSTALLATION GUIDE. KTM 125, 144, Stroke KTM 250, Stroke KTM 250 SXF, XC, XC-W KTM 450, 505 SXF Manual Revision:

INSTALLATION GUIDE. KTM 125, 144, Stroke KTM 250, Stroke KTM 250 SXF, XC, XC-W KTM 450, 505 SXF Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE KTM 125, 144, 200 2-Stroke KTM 250, 300 2-Stroke KTM 250 SXF, XC, XC-W KTM 450, 505 SXF 191-836 Manual Revision: 050307 2002 Rekluse Motor

More information

Nikki Carburetor Vertical Models , ,

Nikki Carburetor Vertical Models , , Nikki Carburetor Vertical Models 280000, 310000, 330000 Disassemble Carburetor 1. Remove fuel bowl screws (A, Figure 56). Remove the fuel bowl (B) from the carburetor body. WARNING Before servicing the

More information

CARBURETION. Carburetor Identification. Models , , , , , , , , , , ,

CARBURETION. Carburetor Identification. Models , , , , , , , , , , , Carburetor Identification Models 110400, 110600, 111400, 111600, 113400, 120400, 120600, 121400, 121600, 122600, 123400, 123600 Models 28S700, 311700 Service Carburetor Briggs & Stratton/Walbro LMS Models

More information

We thank you for purchasing a manual petcock conversion kit from Murphs!

We thank you for purchasing a manual petcock conversion kit from Murphs! We thank you for purchasing a manual petcock conversion kit from Murphs! The first step is removing the gas tank from the bike. We suggest running the tank down to reserve before removal, both for the

More information

INSTALLATION GUIDE. Clutch Cable Actuated Models Manual Revision:

INSTALLATION GUIDE. Clutch Cable Actuated Models Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE Clutch Cable Actuated Models 191-800 Manual Revision: 061810 2002 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise,

More information

The Ford Model A Water Pump

The Ford Model A Water Pump The Ford Model A Water Pump George Washington Chapter, Inc. 3903 Old Lee Highway Fairfax, VA 22030 1 Table of Contents Introduction/Specifications.. 3 1. Water Pump Inspection and Removal. 4 a. Removal..

More information

I suggest you read through this guide first to familiarise yourself with what you need to do before doing it. Let s get into it!

I suggest you read through this guide first to familiarise yourself with what you need to do before doing it. Let s get into it! This guide was written for those with standard (or close to standard) NC30 s that have yet to get up close and friendly with their bike s fuelling system. It was put together using a few different bikes

More information

WEIAND STREET WARRIOR INTAKE MANIFOLD P/N s 8125, 8125P, 8126, & 8126P SMALL BLOCK CHEVROLET

WEIAND STREET WARRIOR INTAKE MANIFOLD P/N s 8125, 8125P, 8126, & 8126P SMALL BLOCK CHEVROLET APPLICATIONS: WEIAND STREET WARRIOR INTAKE MANIFOLD P/N s 8125, 8125P, 8126, & 8126P 262-400 SMALL BLOCK CHEVROLET INSTALLATION INSTRUCTIONS The P/N 8125 & 8126 WEIAND STREET WARRIOR series intake manifolds

More information

CARBURETION. Tank Mount, Horizontal Crankshaft. Vacu-Jet - All

CARBURETION. Tank Mount, Horizontal Crankshaft. Vacu-Jet - All Page 1 of 1 Vacu-Jet - All Carburetor Adjustment Initial 1. Turn adjustment needle clockwise until it makes light contact with the seat. Do not force. 2. The initial setting of adjustment needle is made

More information

Z-Gate Universal Shifter

Z-Gate Universal Shifter Installation Instructions Z-Gate Universal Shifter Fits: GM, Ford, Lincoln and Chrysler Transmissions See Application Guide for Specific Applications Part #80681 Rev 06/01/2018 WORK SAFELY! For maximum

More information

Repairing the CIS Jetronic Alloy adjustable Bosch Fuel distributor

Repairing the CIS Jetronic Alloy adjustable Bosch Fuel distributor CIS-Jetronic.com 07.3-0997-06-01 Repairing the CIS Jetronic Alloy adjustable Bosch Fuel distributor When do you have to repair your CIS Bosch fuel distributor? If your car has rough idle, low power, high

More information

Урал) - Dnepr (Днепр) Russian Motorcycle Carburetors

Урал) - Dnepr (Днепр) Russian Motorcycle Carburetors Ural (Урал( Урал) - Dnepr (Днепр) Russian Motorcycle Carburetors Part 8A: Adjustment and Overhaul of the Pekar K-65 Carburetors (see also Part 8-8 K-65 Carburetor and Part 8B- Setting Up K-65 K Carbs)

More information

2013 IMPCO Technologies, Inc. Page 1 of 20 EPR Repair Kit Instructions (PPI-122, Rev-B)

2013 IMPCO Technologies, Inc. Page 1 of 20 EPR Repair Kit Instructions (PPI-122, Rev-B) EPR Repair Kit Instructions PPI-122 (Rev-B) A. Introduction: This document covers the repair of the Electronic Pressure Regulator (EPR) used on Spectrum III series fuel systems. These instructions will

More information

Go-ped ESR750 / ESR750EX Rear Brake Installation Instructions

Go-ped ESR750 / ESR750EX Rear Brake Installation Instructions Go-ped ESR750 / ESR750EX Rear Brake Installation Instructions This kit provides all the parts you need to install a rear brake on your ESR750 or ESR750EX. It will not work on an ESR Sport, or other Go-ped

More information

DrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*

DrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info* DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for

More information

WEBER CARBURETOR TROUBLESHOOTING GUIDE

WEBER CARBURETOR TROUBLESHOOTING GUIDE This guide is to help pinpoint problems by diagnosing engine symptoms associated with specific vehicle operating conditions. The chart will guide you step by step to help correct these problems. For successful

More information

HW Prowler Carburetor Installation Instructions

HW Prowler Carburetor Installation Instructions HW Prowler Carburetor Installation Instructions Page 1 of 6 Carb Kit Contains: HW modified Mikuni 36mm pumper style carb Custom choke cable Fuel Line Clamp Instructions (2) Leaner and (2) richer main jets

More information

SPEED & ROAD DEMON ELECTRIC CHOKE KIT #421440

SPEED & ROAD DEMON ELECTRIC CHOKE KIT #421440 SPEED & ROAD DEMON ELECTRIC CHOKE KIT #421440 CHOKE INSTALLATION INSTRUCTIONS LIT702 Please make sure you have read and completely understand the instructions before you begin the installation. Keep in

More information

Installation Instructions Z-Gate Shifter

Installation Instructions Z-Gate Shifter Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic

More information

Instructions for repairing the F-Body Hatch Pull-Down Unit By Lon Salgren (ls90rs)

Instructions for repairing the F-Body Hatch Pull-Down Unit By Lon Salgren (ls90rs) Instructions for repairing the 1986-87 F-Body Hatch Pull-Down Unit By Lon Salgren (ls90rs) Lonsal@adelphia.net CAUTION: Completely read and understand the instructions before proceeding. There are some

More information

PRO RATCHET UNIVERSAL SHIFTER

PRO RATCHET UNIVERSAL SHIFTER Installation Instructions PRO RATCHET UNIVERSAL SHIFTER Fits: GM, Ford and Chryslers w/automatic Transmission See Application Guide for Specific Vehicles Catalog # 80842 WORK SAFELY! For maximum safety,

More information

Installing LED lights in a Hypercharger By Keith Edwards Joker s Wild! (Wildjokr)

Installing LED lights in a Hypercharger By Keith Edwards Joker s Wild! (Wildjokr) Installing LED lights in a Hypercharger By Keith Edwards Joker s Wild! (Wildjokr) THINGS YOU WILL NEED: A Hypercharger (duh!) LEDs (The ones I got were from Benny Bryant at Fantasies on Wheels in Sylacauga,

More information

INSTALLATION GUIDE Manual Revision:

INSTALLATION GUIDE Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE KTM 125, 144, 200 2-Stroke KTM 250, 300 2-Stroke KTM 250 SXF, XC, XC-W KTM 400 XC-W KTM 450, 505 SXF, XC-F KTM 450, 530 XCR-W, EXC-R Husaberg

More information

Setting up and adjusting SU/Hitachi carbs on the Datsun Roadster by Keith Williams. Service screw

Setting up and adjusting SU/Hitachi carbs on the Datsun Roadster by Keith Williams. Service screw Setting up and adjusting SU/Hitachi carbs on the Datsun Roadster by Keith Williams Service screw This is the service screw it s only use it to raise the engine speed while adjusting the carbs. In normal

More information

CARBURETOR. Preliminary Check. Removal of DuraForce Carburetor

CARBURETOR. Preliminary Check. Removal of DuraForce Carburetor Fuel Leaks From Carburetor (Leaking starts after running, stops after shutdown) Note: This condition which does NOT drain the fuel tank is called spit-back. Possible Causes Engine RPM out of proper range

More information

CARBURETOR REBUILD KIT (Vacuum Secondary) Models Demon Carburetors & Holley Model 4160 LIT704

CARBURETOR REBUILD KIT (Vacuum Secondary) Models Demon Carburetors & Holley Model 4160 LIT704 CARBURETOR REBUILD KIT 190000 (Vacuum Secondary) Models Demon Carburetors & Holley Model 4160 LIT704 INSTRUCTIONS: Before getting to the actual rebuild, it should be noted that the carbs shown here are

More information

INSTALLATION GUIDE. Clutch Cable Actuated Models Manual Revision:

INSTALLATION GUIDE. Clutch Cable Actuated Models Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE Clutch Cable Actuated Models 191-800 Manual Revision: 041513 2012 Rekluse Motor Sports Rekluse Motor Sports, Inc. 12000 W Franklin Rd. Boise,

More information

Checking Solenoid Plunger Travel

Checking Solenoid Plunger Travel 1985 Chevy Truck EL Camino V8-305 5.0L Page 1 Carburetor: Adjustments Carburetor Calibration E2M & E4M Series Mixture Control Solenoid Plunger Travel Checking Solenoid Plunger Travel OTE: Mixture control

More information

Installation Instructions

Installation Instructions Installation Instructions Magnum Grip Pro Stick Shifter including CARBON FIBER models (see www.bmracing.com for the latest fitment applications and model years) Part # s 81040,81041, 81043, & 81044 2010,

More information

HSR Carburetor Easy Kits Installation Instructions For Evo Big Twin Kit: # 42-7 Twin Cam Kit: # 42-18

HSR Carburetor Easy Kits Installation Instructions For Evo Big Twin Kit: # 42-7 Twin Cam Kit: # 42-18 HSR Carburetor Easy Kits Installation Instructions For Evo Big Twin Kit: # 42-7 Twin Cam Kit: # 42-18 Revised 5/01/01 EK-1 Easy Kit Installation Instructions The HSR series carburetors are precise yet

More information

Maintenance Information

Maintenance Information 04581245 Edition 2 May 2014 Air Grinder, Die Grinder and Sander Series G2 (Angle) Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings,

More information

Maintenance Information

Maintenance Information Form 16575334 Edition 1 April 2005 Electric Screwdrivers EL, EP and ET 34V DC Series Maintenance Information Save These Instructions WARNING Maintenance procedures have the potential for severe shock hazard

More information

ELECRAFT KX3 Application Note

ELECRAFT KX3 Application Note ELECRAFT KX3 Application Note Installing the Speaker Grille Cloth Revision A, July 30, 2012 Copyright 2012, Elecraft, Inc., All Rights Reserved Background Some KX3 owners have reported issues with the

More information

Motorcycle Carburetor Theory 101

Motorcycle Carburetor Theory 101 Motorcycle Carburetor Theory 101 Motorcycle carburetors look very complex, but with a little theory, you can tune your bike for maximum performance. All carburetors work under the basic principle of atmospheric

More information

CARBURETOR - HITACHI 2-BBL

CARBURETOR - HITACHI 2-BBL CARBURETOR - HITACHI 2-BBL 1986 Isuzu Trooper II 1986 Hitachi Carburetors HITACHI DCH340, DCR384, DFP340, DFP384 & DHP340 2-BARREL P UP & Trooper II DESCRIPTION Carburetor is a 2-barrel downdraft type

More information

Installing Nameless Performance High Flow cats on a Jaguar XKR

Installing Nameless Performance High Flow cats on a Jaguar XKR Installing Nameless Performance High Flow cats on a 2000-2002 Jaguar XKR Part I, removal preparation under the hood, left side. 1. Open the hood and remove the coolant tank cap on the driver's side of

More information

Backwater Performance Systems Large Vanguard Mikuni Twin Carburetor Kit

Backwater Performance Systems Large Vanguard Mikuni Twin Carburetor Kit Backwater Performance Systems Large Vanguard Mikuni Twin Carburetor Kit 1. Throttle Cable Twin (CKC-41) 2. Carburetor VM30mm (CKC-40) 3. Loctite 242.5mL (A-210) 4. Air Cleaner Filter 6000 (EC-86) 5. Rev

More information

Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3

Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage

More information

PRO-R AIR CLEANER FOR KAWASAKI 9462

PRO-R AIR CLEANER FOR KAWASAKI 9462 I N S TA L L AT I O N PRO-R AIR CLEANER FOR KAWASAKI 9462 FITS: 95-04 VN1500 (SINGLE CARB MODELS) PART # INCLUDED 500205 1 Pro R Hypercharger Chrome Assembly Including: 1 Dual Velocity Ring (in plastic

More information

3 October 2016 PN# V Dodge Twin Turbo Kit (I-00274) ½ D o d g e 2 4 v I S B

3 October 2016 PN# V Dodge Twin Turbo Kit (I-00274) ½ D o d g e 2 4 v I S B 3 October 2016 PN#1045320 24V Dodge Twin Turbo Kit (I-00274) 1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD Twin Turbo Kit 1998½- 2 0 0 2 D o d g e 2 4 v I S B Part# 1045320 PLEASE READ

More information

TCI FastGate Shifter Installation Instructions

TCI FastGate Shifter Installation Instructions 151 INDUSTRIAL DRIVE ASHLAND, MISSISSIPPI 38603 http://www.tciauto.com TELEPHONE: 662-224-8972 FAX LINE: 662-224-8255 E-MAIL: tech@tciauto.com TCI 616541 FastGate Shifter Installation Instructions The

More information

Service Manual Air Plus Second Stage

Service Manual Air Plus Second Stage Service Manual Air Plus Second Stage Includes XS Series Second Stage Copyright 2002, Cressi-sub Revised 3/2002 2 Air Plus Second Stage Service Manual Contents BEFORE STARTING... 3 DISASSEMBLY... 3 PARTS

More information

Service Manual Air Tech Second Stage

Service Manual Air Tech Second Stage Service Manual Air Tech Second Stage Copyright 2002, Cressi-sub Revised 3/2002 2 Air Tech Second Stage Service Manual Contents BEFORE STARTING... 3 DISASSEMBLY... 3 PARTS CLEANING AND LUBRICATION... 9

More information

Body type location. Model number location. Small Engine Parts

Body type location. Model number location. Small Engine Parts Body type location Model number location Small Engine Parts FUEL PUMP SYSTEM SYSTEMS AND OPERATION The fuel pump on a diaphragm carburetor uses the vacuum and pressure pulse from the engines crankcase

More information

Two seal rings will be installed in each piston groove, total of four rings installed in each piston.

Two seal rings will be installed in each piston groove, total of four rings installed in each piston. When seals removal is complete, piston grooves will have exposed metal with no seals. Wipe clean piston grooves (towel). Repeat seals removal for second piston. Note: Deteriorated O-rings will be flattened

More information

Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT)

Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT) Tools needed: 14mm hex socket 7mm socket/wrench 8mm socket/wrench Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT) 10mm socket (for airbox removal) ¾ inch or 19mm wrench Torque wrench Appropriate ratchets

More information

Base Kit Rochester Tri Power Carb small parts kit contents:

Base Kit Rochester Tri Power Carb small parts kit contents: 910-11589 Base Kit Rochester Tri Power Carb small parts kit contents: Installation of Rochester 2 GC Tri-Power Base Kit Modifications to center (primary) carb 1) Remove, disassemble, and clean carb as

More information

HSR Carburetor. Total Kits. Installation Instructions. # Evo Big Twin # present Twin Cam

HSR Carburetor. Total Kits. Installation Instructions. # Evo Big Twin # present Twin Cam HSR Carburetor Total Kits Installation Instructions HSR42 Kits: HSR45 Kits: #42-8 84-99 Evo Big Twin #42-19 99 - present Twin Cam #45-2 84-99 Evo Big Twin #45-3 84-99 Evo Big Twin #45-4 99 - present Twin

More information

Ford Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours

Ford Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours Ford Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours Tools Required: Ratchet and socket set Torque wrench Large adjustable wrench Needle nose pliers A dozen

More information

HSR Carburetor. Total Kits. Installation Instructions. # Evo Big Twin # present Twin Cam

HSR Carburetor. Total Kits. Installation Instructions. # Evo Big Twin # present Twin Cam HSR Carburetor Total Kits Installation Instructions HSR42 Kits: HSR45 Kits: #42-8 84-99 Evo Big Twin #42-19 99 - present Twin Cam #45-2 84-99 Evo Big Twin #45-3 84-99 Evo Big Twin #45-4 99 - present Twin

More information

FU-1 FUEL SYSTEM. Page PRECAUTIONS... TROUBLESHOOTING... ON-VEHICLE INSPECTION...

FU-1 FUEL SYSTEM. Page PRECAUTIONS... TROUBLESHOOTING... ON-VEHICLE INSPECTION... FU-1 FUEL SYSTEM PRECAUTIONS... TROUBLESHOOTING... ON-VEHICLE INSPECTION... CARBURETOR FUEL PUMP... Page FU-2 FU-2 FU-3 FU-4 FU-28 FU-2 FUEL SYSTEM - Precautions, Troubleshooting PRECAUTIONS 1. Before

More information

Maintenance Information

Maintenance Information 80234313 Edition 1 June 2006 Air Grinder, Die Grinder, Sander and Belt Sander Series G1 (Angle) Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing

More information

Performer Series Carburetor Rebuild Kit Catalog #1477 Models

Performer Series Carburetor Rebuild Kit Catalog #1477 Models Please read these instructions carefully before attempting to rebuild your carburetor. Make sure to refer to your carburetor Owner s Manual for further information if need be. If you have any questions

More information

Turner M50 Manifold Adapter Install. April 26, 2012

Turner M50 Manifold Adapter Install. April 26, 2012 April 26, 2012 Models: 1996-99 E36 328i/M3; 1997-98 E39 528i, 1997-98 Z3 2.8, 1998-2000 MZ3 S52 Product(s): Turner M50 Manifold Adapter Kit Subject: Installation Guidelines and Tips This guide will aid

More information

Chrysler TorqueFlite Shift Improver Kit Part No A-727 (V-8) A-904 (V-8) (A-998 & A-999)

Chrysler TorqueFlite Shift Improver Kit Part No A-727 (V-8) A-904 (V-8) (A-998 & A-999) FORM # 9500606-03 Installation Instructions Chrysler TorqueFlite Shift Improver Kit Part No. 10225 1971-1977 A-727 (V-8) 1971-1977 A-904 (V-8) (A-998 & A-999) 1998, 2005, 2010 by B&M Racing & Performance

More information

TILLOTSON LTD., CLASH INDUSTRIAL ESTATE, TRALEE, CO. KERRY, IRELAND PHONE: FAX:

TILLOTSON LTD., CLASH INDUSTRIAL ESTATE, TRALEE, CO. KERRY, IRELAND PHONE: FAX: TILLOTSON LTD., CLASH INDUSTRIAL ESTATE, TRALEE, CO. KERRY, IRELAND PHONE: +353 66 7121911 FAX: +353 66 7124503 e-mail: sales@tillotson.ie HR SERIES SERVICE MANUAL INTRODUCTION Tillotson has developed

More information

CARBURETOR ROUND SLIDE 2 STROKE ENGINES

CARBURETOR ROUND SLIDE 2 STROKE ENGINES ROUND SLIDE STROKE ENGINES The motorcycle carburetor is a very touchy device that can cause all kinds of trouble if mishandled or neglected. Our experience indicates that most of the carburetors sent under

More information

Maintenance Information

Maintenance Information 80234313 Edition 2 May 2014 Air Grinder, Die Grinder, Sander and Belt Sander Series G1 (Angle) Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the

More information

INSTRUCTION SHEET Rochester Carburetor Models 4G 4GC

INSTRUCTION SHEET Rochester Carburetor Models 4G 4GC INSTRUCTION SHEET Rochester Carburetor Models 4G 4GC General Exploded View The general design and parts shown will vary to individual units covered on this instruction sheet. Disassembly Use the exploded

More information

Tillotson Tc3A Carburator

Tillotson Tc3A Carburator Tillotson Tc3A Carburator 176 FUEL SYSTEMS - 5B-11 CENTER BOWL TYPE CARBURETOR Removal 1. Remove front cowl cover and wrap-around cowl. 2. Remove swivel link from lower carburetor. (Figure 2) 3. Loosen

More information

Installation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683

Installation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 Installation Instructions QuickSilver Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 WORK SAFELY! For maximum safety, perform this installation

More information

Installation instructions for Alpha Racing Quickshifter/Blipper for a pre-2014 S1000RR

Installation instructions for Alpha Racing Quickshifter/Blipper for a pre-2014 S1000RR Skill Level: Intermediate Installation instructions for Alpha Racing Quickshifter/Blipper for a pre-2014 S1000RR Tools Required: Alen keys/socket/drivers Torx keys/sockets/drivers Metric box wrenches and

More information

Installation Instructions Unimatic Shifter

Installation Instructions Unimatic Shifter Installation Instructions Unimatic Shifter Universal Shifter for Automatic Transmissions Part Number 80775 2010, 2000 by B&M Racing & Performance Products The B&M Unimatic is a universal shifter that will

More information

HSR Carburetor Sportster & Buell. Installation Manual. Revised 7/5/00

HSR Carburetor Sportster & Buell. Installation Manual. Revised 7/5/00 HSR Carburetor Sportster & Buell Installation Manual Carb Kit# 42-10 Carb Kit# 42-11 94 - present Sportster All Buells Revised 7/5/00 SB-1 Sportster/Buell Installation The HSR series carburetors are precise

More information

Installation Instructions Unimatic Shifter

Installation Instructions Unimatic Shifter Installation Instructions Unimatic Shifter Universal Shifter for Automatic Transmissions Part Number 80775 2000 by B&M Racing & Performance Products LLC The B&M Unimatic is a universal shifter that will

More information

Stealth Pro Ratchet Shifter

Stealth Pro Ratchet Shifter Installation Instructions Stealth Pro Ratchet Shifter Part Number 81120 & 81121 (see www.bmracing.com for the latest technical product information) 2010, 2006 by B&M Racing and Performance Products The

More information

Sherco Engine Teardown and Assembly Manual

Sherco Engine Teardown and Assembly Manual Sherco Engine Teardown This Manual is provided as a guide for: Removing the engine from the frame Splitting the cases Complete Disassembly of the engine Reassembly of the engine Reinstallation back in

More information

Technical Support (707)

Technical Support (707) Installation Instructions UNIMATIC SHIFTER Fits: GM, Powerglide, Ford and Chrysler Transmissions See Application Guide for Specific Vehicles Catalog # 80775 WORK SAFELY! For maximum safety, perform this

More information

WEIAND INTAKE MANIFOLD P/N 7550 SMALL BLOCK CHEVROLET 3x2 BBL

WEIAND INTAKE MANIFOLD P/N 7550 SMALL BLOCK CHEVROLET 3x2 BBL WEIAND INTAKE MANIFOLD P/N 7550 SMALL BLOCK CHEVROLET 3x2 BBL INTAKE MANIFOLD INSTALLATION INSTRUCTIONS 199R10703 APPLICATIONS: The P/N 7550 WEIAND intake manifold is designed for Holley 3x2 BBL, model

More information

Installation Instructions Hammer Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80885

Installation Instructions Hammer Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80885 Installation Instructions Hammer Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80885 WORK SAFELY! For maximum safety, perform this installation on

More information

INSTALLATION GUIDE. KTM 950/990 LC8 Engine Manual Revision:

INSTALLATION GUIDE. KTM 950/990 LC8 Engine Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE KTM 950/990 LC8 Engine 191-631 Manual Revision: 071510 2007 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise, Idaho

More information

Maintenance Information

Maintenance Information Form 16573321 Edition 1 July 2004 Air Grinder Series 61H Maintenance Information Save These Instructions Always wear eye protection when operating or performing maintenance on this tool. Always turn off

More information

BEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta).

BEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta). BEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta). Based on the procedure published by Volkswagen, but modified for the "average" shadetree mechanic. Some special

More information

Holley GM BBC Single-Plane EFI Intake Manifold Kits

Holley GM BBC Single-Plane EFI Intake Manifold Kits Holley GM BBC Single-Plane EFI Intake Manifold Kits 300-561 Oval Port, 4150 Flange 300-562 Oval Port, 4500 Flange 300-563 Rectangular Port, 4150 Flange 300-564 Rectangular Port, 4500 Flange INSTALLATION

More information

This is a guide to assist you adjust the valve clearance on a 2l V6 MIVEC engine found in a Mitsubishi FTO GPX

This is a guide to assist you adjust the valve clearance on a 2l V6 MIVEC engine found in a Mitsubishi FTO GPX Adjusting the valve clearance on a 2L V6 FTO engine This is a guide to assist you adjust the valve clearance on a 2l V6 MIVEC engine found in a Mitsubishi FTO GPX Disclaimer: This guide is to assist you

More information

5. FUEL SYSTEM 5-0 FUEL SYSTEM UXV 500

5. FUEL SYSTEM 5-0 FUEL SYSTEM UXV 500 5 FUEL SYSTEM 5 SERVICE INFORMATION------------------------------------------------ 5-02 TROUBLESHOOTING----------------------------------------------------- 5-03 FUEL TANK -----------------------------------------------------------------

More information

*Some speedometers have these additional electronic connections. If yours does, then remove the smaller slotted screws shown.

*Some speedometers have these additional electronic connections. If yours does, then remove the smaller slotted screws shown. www.odometergears.com 1981-1985 240 Cable-Driven Speedometers (NOT for 1986 and later electronic units) http://www.davebarton.com/240-odometer-repair.html For this set of instructions below, I will not

More information

Kodak 750H Carousel Projector Repair

Kodak 750H Carousel Projector Repair Kodak 750H Carousel Projector Repair An AT YOUR OWN RISK PROJECT by Klaus Wolter, Rev B, 3-26-2016 Here I documen the repair of my 750H carousel. A common problem with this projector, and all of the projectors

More information

Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod

Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.

More information

Fluid-O-Tech ROTOFLOW ROTARY VANE PUMP REBUILD MANUAL

Fluid-O-Tech ROTOFLOW ROTARY VANE PUMP REBUILD MANUAL Fluid-O-Tech PUMP TECHNOLOGY AT ITS BEST WWW.FLUID-O-TECH.COM Office: 161 Atwater St., Plantsville, CT 06479 Phone: (860) 276-9270 Fax: (860) 620-0193 ROTOFLOW ROTARY VANE PUMP REBUILD MANUAL 08/09 Ed.,

More information

THE IDIOT S GUIDE TO TUNING SU CARBURETTERS

THE IDIOT S GUIDE TO TUNING SU CARBURETTERS THE IDIOT S GUIDE TO TUNING SU CARBURETTERS There are four distinct phases to tuning SU carburetters (carbies). The first is to set the fuel level in the float bowl, the second is to centre the needle

More information