PSC-2. Herion 18D Pneumatic pressure switches (diaphragm type) Vac psi. Pressure sensing and control

Transcription

1 Pressure sensing and control Herion 18D Pneumatic pressure switches (diaphragm type) Vac psi p DIN 4365 Adjustable setpoint Gold-plated contacts Vibration resistant to 15 g Microswitch approved by UL and CSA Technical data Medium Neutral, gaseous and liquid fluids Operation Diaphragm Mounting position Optional Operating pressure Vac to 435 psi Over pressure 115 psi Ambient temperature -14 F to 175 F (-1 C to + 8 C) Viscosity Up to 1 mm 2 /s (±45 ssu). Fluid temperature -14 F to 175 F (-1 C to +8 C) Repeatability ±3%, for vacuum ±4% Electrical connection DIN Switching element Microswitch Degree of protection IP 65 Weight.4 lbs (.2 kg) Materials Housing: aluminum Seals: Perbunan, Viton O -ring: NBR Model numbers - pneumatic/lubrication applications Port Type Pressure range Switching pressure Model Drawing size psi (bar) difference psi* (bar) lower upper range range 1/4 NPT Female -14 (-1 ) 2 (.15) 3 (.18) Flange -14 (-1 ) 2 (.15) 3 (.18) /4 NPT Female 3 3 (.2 2) 2 (.15) 4 ( Flange 3 3 (.2 2) 2 (.15) 4 (.27) /4 NPT Female 7 12 (.5 8) 4 (.2) 9 (.65) Flange 7 12 (.5 8) 4 (.2) 9 (.65) /4 NPT Female (1 16) 4 (.2) 13 (.9) Flange (1 16) 4 (.2) 13 (.9) /4 NPT Female (1 3) 15 (1.) 75 (5.) Note: Switches are supplied with DIN 4365 mating connector. * Switching pressure difference (hysteresis) is not adjustable. Typical valves are shown. Caution: Observe switching range. Do not subject switch to maximum allowable pressure during normal operation. Even short pressure peaks must not exceed this value. PSC-2

2 Herion 18D Pneumatic pressure switches Vac psi Making And/Or Breaking Capacity Load Level* Type of Current Type of Load Vmin [V] Maximum Permanent Current Imax [A] at V Contact life 24 V 125 V 25 V electrical mechanical at I max at I = Standard AC Resistive x 1 4 approx 1 7 (relays, switching switching solenoids) AC Inductive cycles cycles PF =.7 DC Resistive DC Inductive L/R = 1 ms Low AC Resistive x 1 5 approx 1 7 (electronic switching switching circuits) DC Inductive cycles cycles L/R = 1 ms *Load Level Explanation Series 18D Pressure Switches have microswitch contacts with gold-plating over silver base metal. The gold plating remains intact when low level voltage / current levels are observed. This feature assures highly reliable switching in low-level electronic circuits. Standard applications do not require the gold plating which will decay naturally when switching larger electrical loads. Notes: 1. Reference conditions: 3 cycles per min and 86 F (3 C) ambient. 2. Reducing load current to 5% of I max approximately doubles contact life. 3. Creepage and clearance distances correspond to insulation group B per VDE Reg. 11 (except contact clearance of microswitch. 1 (3).79 (2) (3) 2.95 (75) Switch Adjustment 2 (3).79 (2) (3) 2.95 (75) Switch Adjustment.59 (15).21 (5.3).61 (15.5) 2.83 (72).59 (15).21 (5.3).37 (9.5) 2.83 (72) 1 *G1/4 NPT or 1/4 G 1 /4NPT 1 NPT or G 1 /4 *G1/4 or 1/4 NPT 3 Protective Cover An optional elastomer cover for protection of the switch adjustment against dirt and splashing liquids Part No (3) 2.95 (75) Switch Adjustment (3).79 (2) (3).28 (7).59 (15).21 (5.3) 2.83 (72) (3).6 (1.5).315 (8) dia recess at pressure inlet for O-ring. (O-ring supplied with switch) PSC-3

3 Pressure sensing and control Herion 18D Hydraulic pressure switches (piston type) 7 to 61 psi psi p DIN 4365 Adjustable setpoint Gold-plated contacts Vibration resistant to 15 g Microswitch approved by UL and CSA Technical data Medium Hydraulics, lubricating and light fuel oils Operation Piston Mounting position Optional Operating pressure 7 to 61 psi Over pressure 58 psi, 8824xx: 87 psi Ambient temperature -4 F to 175 F (-2 C to + 8 C) Viscosity Up to 1 mm 2 /s (±45 ssu). Fluid temperature -4 F to 175 F (-2 C to +8 C) Repeatability ±3% Electrical connection DIN Switching element Microswitch Degree of protection IP 65 Weight.2 lbs (.2 kg) Materials Housing aluminum Port: stainless steel Seals: Teflon/Buna-N Model numbers - hydraulic applications Switching Pressure Difference (Hysteresis)* Port Type Pressure Range psi (bar) Size psi (bar) Lower Upper Model Dimension Range Range Drawing No. - flange (5 7) 152 (1.5) 218 (15) /16-2 UNF female (5 7) 152 (1.5) 218 (15) /4 NPT female (5 7) 152 (1.5) 218 (15) flange (1 16) 16 (11) 247 (17) /16-2 UNF female (1 16) 16 (11) 247 (17) /4 NPT female (1 16) 16 (11) 247 (17) flange (25 25) 16 (11) 247 (17) /16-2 UNF female (25 25) 16 (11) 247 (17) /4 NPT female (25 25) 16 (11) 247 (17) flange (4 42) 247 (17) 58 (35) /16-2 UNF female (4 42) 247 (17) 58 (35) /4 NPT female (4 42) 247 (17) 58 (35) Note: Switches are supplied with DIN 4365 mating connector * Switching pressure difference (hysteresis) is not adjustable. Maximum values are shown. PSC-4

4 Herion 18D Hydraulic pressure switches Vac psi Making And/Or Breaking Capacity Load Level* Type of Current Type of Load Vmin [V] Maximum Permanent Current Imax [A] at V Contact life 24 V 125 V 25 V electrical mechanical at I max at I = Standard AC Resistive x 1 4 approx 1 7 (relays, switching switching solenoids) AC Inductive cycles cycles PF =.7 DC Resistive DC Inductive L/R = 1 ms Low AC Resistive x 1 5 approx 1 7 (electronic switching switching circuits) DC Inductive cycles cycles L/R = 1 ms *Load Level Explanation Series 18D Pressure Switches have microswitch contacts with gold-plating over silver base metal. The gold plating remains intact when low level voltage / current levels are observed. This feature assures highly reliable switching in low-level electronic circuits. Standard applications do not require the gold plating which will decay naturally when switching larger electrical loads. Notes: 1. Reference conditions: 3 cycles per min and 86 F (3 C) ambient. 2. Reducing load current to 5% of I max approximately doubles contact life. 3. Creepage and clearance distances correspond to insulation group B per VDE Reg. 11 (except contact clearance of microswitch. 1 Switch Adjustment 2 (3) 2.95 (75).79 (2) (3) (3).79 (2) (3) 2.95 (75) Switch Adjustment.59 (15).21 (5.3) Protective Cover An optional elastomer cover for protection of the switch adjustment against dirt and splashing liquids Part No (3).28 (7) (3).6 (1.5).31 (8) 2.83 (72) Pressure port material: 43 SS (1.414) 1 /4 NPT, G 1 /4 or 7/16-2 UNF.59 (15).21 (5.3) 2.83 (72).315 (8) dia recess at pressure inlet for O-ring. (O-ring supplied with switch) PSC-5

5 Pressure sensing and control Herion 33D Series Solid state switches (pneumatic / all-fluid) Vac to 91 psi Real time pressure display with backlight Compact and robust design Easy programming of set points and additional functions Transistor output signals 1 x PNP, 2 x PNP, or 1 x PNP + 4 to 2 ma Electronic lock Switching status indicated by LED Standard M12x1 electrical connection (IP 65) For pneumatic, all fluid and hydraulic applications Technical data Medium Pneumatic types: compressed air or neutral gases All fluid types: gasses or liquids, including aggressive Display LCD 4 digits illuminated, pressure unit programmable for bar, psi, mpa Mounting position Optional Operating pressure Vac to 23 psi (pneumatic) to 91 psi (hydraulic/allfluid) Temperature sensitivity (zero point).4% of final value/1 K Temperature sensitivity (range).4% FS/1 K Ambient temperature 14 F to 14 F (-1 C to 6 C) Fluid temperature 14 F to 75 F (-1 C to 8 C) Switching point Adjustable between and 1% FS Reset point Adjustable between and 1% FS Electrical connection M12 x 1 Linearity <.2% FS ±1 digit Degree of protection to DIN 4 5 IP 65 (with mounted plug) Model number - standard pneumatic models* Port Measuring range (psi) Maximum overpressure Output Model size (relative pressure) (psi) signal 1/4 NPT Vac x PNP Flange Vac x PNP /4 NPT Vac x PNP Flange Vac x PNP /4 NPT Vac x PNP / 4 2 ma Flange Vac x PNP / 4 2 ma /4 NPT x PNP Flange x PNP /4 NPT x PNP Flange x PNP /4 NPT x PNP / 4 2 ma Flange x PNP / 4 2 ma * M12 x 1 connector not included. Please see table on next page. Options selector Pressure range (pneumatic) Substitute Vac 15 psi 23 psi 2 Pressure range (allfluid) Substitute 145 psi 1 58 psi psi 4 23 psi 5 36 psi 6 58 psi 7 91 psi 8 Materials Housing: aluminum Pneumatic version Seal : viton O-ring (FKM) Sensor: silicon Hydraulic/All fluid version Porting block / sensor: 316 SS welded 863 Fluid/electrical connection Substitute GÊ, M12 x 1 2 Ê NPT, M12 x 1 4 Flange, M12 x 1 6 Output signal Substitute 1 digital out 1 2 digital out 2 1 digital out/4 2 ma** 4 ** 4-2 ma option not available on flange mounted versions. PSC-6

6 Electrical parameters Electrical connection M12 x 1 Power supply 1 32 V d.c. (polarity safe) digital models V d.c. (polarity safe) analog models Permissible residual ripple 1% (within 12 to 32 V) Current consumption <5 ma (plus load current) Electromagnetic compatibility Interference emission Conforming to EN 581. Part 1 Interference immunity Conforming to EN 582. Part 2 Electrical connection M12 x 1 Pin Signal Cable 1 Supply voltage Brown 2 Out 2 (PNP) / analog 4 2 ma White 3 Common Blue 4 Out 1 (PNP) Black 5 Earth ground Grey Front view M 12 Rear view (flange version) Herion 33D Series Solid state pressure switches (pneumatic / all-fluid) Vacuum to 91 psi Switching output Switching mode Output voltage Analog output Contact rating Switching time Damping Signal delay: Service life Switching logic Operating mode Accessories PNP sourcing type transistor, suitable for inductive load Supply voltage -1.5 V 4 2mA Imax = 5 ma (short-circuit proof) < 1 ms 5 ms.64 sec programmable On/off to 2 sec programmable min. 1 million switching cycles n.o. / n.c. programmable Standard, hysteresis and window mode Separately selectable for each output Part number Connectors and cordsets (M12 x 1)* Mating connector 5-pin straight w/screw terminals, no cable Molded cordset 5-pin straight w/2m cable Molded cordset 5-pin 9 w/2m cable * must be ordered separately.45 (11.5).87 (22) OUT1 HYS WIN OUT2.75 (19) SET 2.81 (71.5) 1.56 (39.7) 3.86 (98) Incorporating.59 (15) (3).79 (2) * Suitable for M 5 x 35 or 1-24 screws ** Flange diameter 8 x 1.2 deep, O-ring 4.47 x 1.78 (Viton 9) * ** (3) PSC-7

7 Pressure sensing and control Herion 18S Allfluid Series Analog pressure sensor for hydraulic / all-fluid applications, - 11,6 psi P I P U Robust sensor for hydraulic applications Temperature compensated 3-wire technology ( to 1 V) 2-wire technology (4 to 2 ma) Excellent long-term stability Stainless steel measuring elementnot oil-filled Technical data Medium For neutral and aggressive gases or fluids Fluid connection 1/4 NPT male Mounting position Optional Pressure range to 11,6 psi Fluid temperature: -4 F to 185 F (-2 C to +85 C) Ambient temperature -4 F to 185 F (-2 C to +85 C) Degree of protection IP 65 (acc. to DIN 45) Shock protection 3g, to DIN EN Vibration protection 3g, 5 to 5 Hz, xyz, DIN EN Electrical connection M12 x 1 Supply voltage U B = 12 to 3 V d.c. (current output) U B = 15 to 3 V d.c. (voltage output) Output signal 4 to 2 ma (Two-wire technology) to 1 V (Three-wire technology) Electromagnetic compatibility Interference immunity acc. to EN 581. Part 1 Interference immunity acc. to EN 582. Part 2 Load resistance See diagram Polarity Short-circuit proof Measuring range See table below Standard models* Model Measuring range (psi) (Relative pressure)** Value max. (bar) (Over pressure) Output signal ma V ma V ma V ma V ,8 4 2 ma ,8 1 V ,6 14,5 4 2 ma ,6 14,5 1 V * Order mating connector separately Linearity < ±.5% FS Hysteresis <.15% FS Temperature sensitivity (zero point) Zero point < ±,4% FS/1K Range < ±.2% FS/1K Materials Housing: 316 stainless steel Sensor: 316 stainless steel welded Electrical connection M 12 x 1 (4 pin) 3 2 Signal ma... 1 V + UB (supply) 1 1 Common Signal 4 4 Options selector Frequency Measuring range relative pressure Code to 145 psi 1 to 36 psi 3 to 145 psi 4 to 3625 psi 6 to 58 psi 7 to 11,6 psi 9 Output signal Code 4 to 2 ma 7 to 1 V PSC-8

8 Herion 18S Pressure sensor analog to 11,6 psi Electrical diagram for 2-wire versions 4 to 2 ma 1 UB P P I 4 + Characteristic load curve 9 RL Ω = I Output 2 = Load U 6 Electrical diagram for 3-wire versions to 1 V P P U U T U + U UB V 1/4 NPT ø.37 (9.5) max. 3 ø.12 (3).51 (13).43 (11).12 (3) (66).47 (12) M12 x 1 ø.67 (17) Max. load RL = U B 12 V ( ).2 A ø.2 (5) ø.43 (11) Weight: 2.5 oz. Accessories Part number Connector and cordsets (M12 x 1) mating connector, 4-pin straight w/screw terminals, no cable molded cordset, 4-pin straight, 2 meter molded cordset, 4-pin straight, 5 meter molded cordset, 4-pin 9, 2 meter molded cordset, 4-pin 9, 5 meter PSC-9

9 Pressure sensing and control Herion 18S Pneumatic Series Analog pressure sensor for pneumatic applications to 36 psi P I Temperature compensated Robust design for pneumatic and industrial applications Technical data Medium: Filtered compressed air, lubricated or unlubricated, neutral gases Mounting Optional Operating pressure 1.4 to 363 psi (-1 to 25 bar) Fluid temperature 14 F to 185 F (-1 C to +85 C) Ambient temperature 14 F to 185 F (-1 C to +85 C) Degree of protection IP 65 Electrical connection DIN or M12 x 1 short-circuit protected Output signal 4 to 2 ma (Two-wire technology) Linearity < ±.5% final scale Hysteresis <.15% Temperature sensitivity (zero point) Zero point < ±.4% FS/1K Range < ±.2% FS/1K Weight:.3 oz. (.15 kg) Materials Housing: aluminum Sensor: Silicon O-rings: NBR Model numbers* Measuring range (bar) Value max. (bar) (Relative pressure) (Over pressure) 1/4 NPT to Flange to /4 NPT to Flange to /4 NPT to Flange to * M12 x 1 connector not included. Please see table below. Port size Model DIN 4365 Model M12x1* Characteristic curve of load RL Ω UB V Max. load RL = UB 1 V,2 A (Ω) PSC-1

10 Herion 18S Pressure sensor analog -1 to 25 bar Electrical connection DIN 4365 M12 x 1 Pin Wiring Pin Wiring 1 + UB 1 + UB 2 Signal ma 4 Signal ma P P I 1 2 UB ma Load + Accessories Connector cordsets (M12 x 1) Model Description Straight, without cable Straight, 2 m cable, 4-pin Straight, 5 m cable, 4-pin m cable, 4-pin m cable, 4-pin + U DIN 4365 Ê NPT 2 x ø.2 (2 x ø 5.2) (3) Plug DIN 4365 * (3) (3) 1.1 (25.7) 3.15 (8) M12 x 1 Ê NPT 2 x ø.2 (2 x ø 5.2) (3) M 12 x 1.51 (13) (3) (3) 1.1 (25.7).89 (22.5).79 (2) Plug DIN 4365 * (3) (3).89 (22.5).51 (13) 2 x ø.2 (2 x ø 5.2) 1.1 (25.7) (3) 3.23 (82).89 (22.5).51 (13) 3.15 (8).79 (2) Flange Flange (3) (3).89 (22.5) 3.23 (82) M 12 x 1 2 x ø.2 (2 x ø 5.2) (3) 1.1 (25.7).51 (13).79 (2).59 (15) Ø 8 x 1.2 deep *.59 (15).79 (2) Ø 8 x 1.2 deep.59 (15) *.59 (15) * O-ring 5 x 1.5 PSC-11

11 Proportional valves VP4 Series 3-way proportional pressure control valves 1/8, 1/4, and 3/8" Low hysteresis Good repeatability High flow capacity at exhaust Manifold mountable Compact design Technical data Medium: Compressed air, filtered to 4 µm, lubricated or unlubricated Mounting position: Any, preferably vertical Flow direction: Fixed Ambient temperature: 14 F to 14 F (-1 C to +4 C) Hysteresis: < 3% FS* Repeatability: < 1% FS* Linearity: See characteristic curves Response sensitivity: 1% FS* * at 2 C Degree of protection: IP 65 with connector Materials Body: aluminum alloy Seals: NBR Orifice Port Outlet pressure Maximum inlet Rated current (ma) Model (mm) size P2 (psi) pressure P1 (psi) 4 1/8 NPT to to 16 (18) /8 NPT to to 16 (18) /4 NPT to 3 1 to 16 (18) /4 NPT to to 16 (18) /8 NPT to to 16 (18) Drive electronics pq11 Model Rated current ma Type of connection Remarks to 24 Connector according to DIN Suitable for 488xxx.xxxx valves to 24 2 m cable Suitable for 488xxx.xxxx valves Drive electronics pq12 Model Rated current ma Remarks to 24 Suitable for 488xxx.xxxx valves Electrical information for proportional solenoids Nominal diameter Limiting current IN Rated power PN Resistance R2 Duty cycle 4, 6 & 8 16 ma 22 W 6.5 ohms + 3% 1% PSC-12

12 Characteristic curves VP4 Series 3-way proportional pressure control valves NPT Â, NPT Ê, NPT Á, Outlet Pressure (PSI) Outlet Pressure (PSI) Flow (SCFM) Fig. 3 Valve Flow (SCFM) Fig. 4 Valve Outlet Pressure (PSI) Outlet Pressure (PSI) Flow (SCFM) Fig. 5 Valve Flow (SCFM) Fig. 6 Valve Outlet Pressure (PSI) Flow (SCFM) Fig. 8 Valve PSC-13

13 Proportional valves VP6 5/3 Proportional flow control valve (nominal dia. 8 mm) Directly operated spool valve with µp-electronics Microprocessor control electronics High dynamic regulation On-board diagnostics CE conformance Technical data Medium Filtered unlubricated air. Note: Using lubricated air may affect dynamic response and lifespan of the valve. Filtration Recommended 5µ Operation Moving coil Connection 1/4 NPT and G1/4" Flow rate 4 scfm (12 l/min) for p1: 9 psi and p2: 75 psi Mounting position Any, preferred solenoid on top Flow direction 1apple4+2apple3; 1apple2+4apple5 Operating temperature: 32 F to 14 F ( C to 6 C) No condensation permissible Materials Electronic housing: plastic (PAA) valve housing: aluminum alloy seals: NBR solenoid surface: steel Degree of protection IP65 Operating pressure [p1] to 175 psi Leakage For center position 35 scfh with p1: 145 psi Reaction time At p1 = 9 psi and 1% stroke free exhausting: Dead time: 3 ms Rise time (1% - 9%): 5ms Electromagnetic compatibility The valve conforms to the EC requirements EN581-2 (emission) and EN582-2 (disturbance noise). For this specification shielded cables have to be used. Symbol W X µp Electrical information Power supply requirements Supply voltage U B [VDC] Current consumption with max. stroke 5 Hz (A) 2. at 24 VDC Current consumpton in steady state [A].1 at 24 VDC Input signal Analog (single ended types) Voltage signal UE [V]...1 Input resistance R I [k ] 11 Current signal I E [ma] () Load resistance [ ] 5 Analog (differential types) Voltage signal U E [V] Input resistance R I [k ] 11 max. Input voltage range [V] Output signal Spool position feedback (voltage) Voltage signal slide position U A [V]...1 V = min...max. stroke Max. output current I A [ma] 1 Spool position feedback (current) Current signal slide position I A [ma]...2 ma = min...max. stroke Load resistance R L [ ] recommended 5 PSC-14

14 VP6 5/3 Proportional control valve Directly operated spool valve with µp-electronic position control Order information VP 6 xx x x x x x x xxxx Proportional Family Flow Unit Port Input Feedback** Power Electrical Options valve code range size signal* supply connector VP 6 1 = 1 L = liter/ J = G 1/4" 1 = -1V 6 = -1V 1 = required M = M12 x 1 = no options min K = G 1/4 4 = 4-2- ma and 8-pin NPT 6 = -5V to +5V 4-2mA 7 = -1V *Input signal codes 6 and 7 are differential input versions. ** Both -1V and 4-2 ma feedback signals are available simultaneously. Accessories Description SpecificationType cordset M12 x 1, 8-pin, 5m, straight cordset M12 x 1, 8-pin, 5m, 9 angle (4.5) 4.77 (121.2).94 (24).59 (15).9 (2.3).2 (5).72 (18.2) (28.6) 1.83 (46.6) 2.54 (64.6) 4.94 (125.5) 1.79 (45.5) 1.79 (45.5) 3.94 (1) 3.43 (87) Flow rate SCFM (l/min) 42. (12) 38.5 (11) 35. (1) 31.5 (9) 28. (8) 24.5 (7) 21. (6) 17.5 (5) 14. (4) 1.5 (3) 7. (2) 3.5 (1) Set point Flow Rate Curve VP6 P1=87psi (6 bars), P2=72.5 psi (5 bars) 3 Port 1-4 Port (4).61 (15.5) 2.2 (55.6) 1.4 (35.6) ø.19 (4.8).2 (5).59 (15) Setpoint [v] ø.31 (8) PSC-15

15 Pressure sensing and control VP1 Electronic Pressure Regulator Reliable, rugged proportional I/P and E/P converters Suitable for a wide range of applications Excellent accuracy High flow versions NEMA4 environmental protection in normal operation Technical data Medium: Oil free, dry air, filtered to 5 micron Output pressure: 3-15 psig (.2-1. bar), 3-3 psig (.2-2. bar), 3-6 psig (.2-4. bar), 2-12 psig (.14-8 bar) three wire version Flow capacity: Up to 1 scfm (3 l/min) Air consumption <6 psig (<4 bar):.3 scfm (.85 l/min) typical >6 psig (>4 bar):.6 scfm (1.75 l/min) typical Operating pressure: At least 1 psig (.7 bar) above maximum required output pressure Connections: NPT 1/4" or 1/4 ISO G available Operating temperature: -4 to 16 F (-2 C to 7 C) Response time <3 psig (<2 bar): less than.5 seconds for 1-9% step change >3 psig (>2 bar): 2 seconds for 1-9% step change Total error: ±.5% of span (typical, independent error includes the combined effect of non-linearity, hysteresis, deadzone and repeatability) Temperature effect: Typically.1% of span/ F for span and zero over operating range Supply sensitivity: >.25% span output change per % supply pressure change Failure mode: Signal falls to bleed pressure when electrical supply fails Mounting: Integral surface mounting bracket provided for preferred vertical mounting. 5 mm pipe mounting kit available Material of construction: Zinc die-casting passivated and epoxy paint, nitrile diaphragms, stainless steel/nylon flapper nozzle and supply valve Mass: 3.3 lbs (15g) approx. Pressure range and input signal options Part Number Control signal Output pressure Calibration Thread form* VP11PK1A -1 V 3-15 psi (.2-1 bar) PSIG 1/4" NPT VP11PK4A 4-2 ma 3-15 psi (.2-1 bar) PSIG 1/4" NPT VP12PK1A -1 V 3-3 psi (.2-2 bar) PSIG 1/4" NPT VP12PK4A 4-2 ma 3-3 psi (.2-2 bar) PSIG 1/4" NPT VP14PK1A -1 V 3-6 psi (.2-4 bar) PSIG 1/4" NPT VP14PK4A 4-2 ma 3-6 psi (.2-4 bar) PSIG 1/4" NPT VP16PK11A -1 V 3-9 psi (.2-6 bar) PSIG 1/4" NPT VP16PK41A 4-2 ma 3-9 psi (.2-6 bar) PSIG 1/4" NPT VP18PK11A -1 V 3-12 psi (.2-8 bar) PSIG 1/4" NPT VP18PK41A 4-2 ma 3-12 psi (.2-8 bar) PSIG 1/4" NPT Electrical Information Electromagnetic compatibility This is a passive electromagnetic instrument and is unaffected by interfering high frequency signals Electrical signal Two wire version 4-2 ma or -1 V for 6< PSIG Three wire version requires V d.c. supply Connections 3 mm square connector DIN 4365 provided, mountable in four directions (alternative connections available) * Replace PK w/bj for calibration in Bar and 1/4 ISO G thread form. ISO Symbols PSC-16

16 Typical Performance Characteristics bar 8 psig 12 FORWARD FLOW CHARACTERISTICS Supply Pressure 1 psig (7 bar) VP1 Electronic Pressure Regulator OUTLET PRESSURE Connector Wiring Input Signal 3 Two vire version <=6 PSIG wire: + to #1 to # scfm 2 1 Three wire version wire: + to #1 to #2 Input signal to # l/min FLOW bar 8 psig 12 RELIEF FLOW CHARACTERISTICS Supply Pressure 1 psig (7 bar) 1 OUTLET PRESSURE (73) 2.13 (54) scfm N l/m in FLOW Plug Orients 4-Ways 1.57 (4) 2.13 (54).87 (22) 4.72 (12) 2 (51) Range or Span (Typical) Supply In Mounting Holes.26 (6.5) Output 1.63 (42).75 (19) CRS Dimensions in Inches (mm) Front View Removable Orifice Rear View Mtg Bracket Holes Ø.15 (3.7) NC = Normally closed, NO = Normally open, APB = All ports blocked, COE = Center open exhaust, COP = Center open pressure **** Insert coil connector code from Connectors table. For manual override options, substitute x as follows: 1 = without manual override, 2 = locking, 3 = non-locking, PSC-17

17 Pressure sensing and control VP5 Proportional Pressure Control Valve Air piloted proportional pressure control valve Fully user adjustable for a wide range of applications High speed Lower power consumption High flow capacity Optional manifold mount utilizes the ISO Size 2 subbase Technical Data Medium: Compressed air, filtered to 4micron, non-lubricated Operation: Proportional, direct acting air piloted spool Output Pressure: See website Supply Pressure: 2 psig (14 bar) max Supply Sensitivity: Better than.75% span output change per bar supply pressure change Flow Capacity: Up to 5 scfm (14 Nl/min) Response Time: < 8 ms (from 1-9% of output pressure into a.1 litre load) Air Consumption: <.177 scfm (5 l/min) Port Size: 1/4 PTF (G1/4) Total Error: Max. error < ±1% of span (independent error includes the combined effect of non-linearity, hysteresis, deadzone and repeatability) Operating Temperature: 23 to 12 F (-5 to 5 C) Temperature Effect: Typically better than.3% of span/ C for span and zero over operating range Degree of protection: NEMA 4 (IP65) in normal operation Vibration Immunity: < 3% output shift for 3g 1-2Hz Mounting Position: Any screw mounting or manifold mount Material of Construction: Aluminium body, zinc diecast lid and end cover Weight: 1.76 lbs. (8g) approx Part Number* Pressure Range and Input Signal Options Port Control Signal Output Pressure in Size psig (bar) VP51PK111H -1V -145 ( -1) 1/4" PTF VP51PK411H 4-2mA -145 ( -1) 1/4" PTF VP56PK111H -1V -9 ( -6) 1/4" PTF VP56PK411H 4-2mA -9 ( -6) 1/4" PTF VP52PK111H -1V -3 ( -2) 1/4" PTF VP52PK411H 4-2mA -3 ( -2) 1/4" PTF * To specify regulator calibration in BAR use B in the 7th position For 1/4" ISO G ports use J in the 8th position. To order the VP5 with interface for manifold mounting, indicate an X in the 8th position of the part number. All units shipped with M12 five pin electrical connector Electrical information Electromagnetic Compatibility CE marked: conforms to E.C. requirements EN (1994) and EN (1995) Electrical Input Signal 4-2mA or -1V factory set Electrical Power Input 24V dc ±25% (power consumption < 1W) Output Pressure Feedback Signal -1V full range Connections DIN 4365 or Brad Harrison connection for feedback output Symbol p PSC-18

18 VP5 Proportional Pressure Control Valve Instrument pin configuration Characteristic Curves V d.c. supply 2-1 full range 3 Control signal (+ve) 4 Common (DC supply, signal and feedback return) 5 Chassis (earth) Outlet Pressure in psig (bar) (1) 145 (9) 131 (8) 115 (7) 12 (6) 87 (5) 73 (4) 58 (3) 44 (2) 29 (1) 15 Forward Flow Characteristics Supply Pressure 16 psig (11bar) (2) (4) (6) (8) (1) (12) (14) (16) Flow in SCFM (Nl/min) Outlet Pressure in psig (bar) Relief Flow Characteristics Supply Pressure 131 psig (9 bar) (9) 131 (8) 116 (7) 12 (6) (5) (4) (3) (2) (1) (-2) (-15) (-1) (-5) Flow SCFM (Nl/min) Accessories Designation Specification Type Connectors with cable M12 x 1.5 pin; 16 ft (5m) 5 x.34 mm M12 x 1.5 pin; 3 ft (1 m) 5 x.34 mm Manifold Mounting Kit Interface plate, gasket, mounting screws 53ZZ5M NOTE: Refer to website to select an ISO 2 size base and accessories..28 (7) 1.97 (5) 1.42 (36).28 (7) 1.1 (28) 3.85 (98) 2.15 (55).43 (11).28 (7) 1.38 (35).97 (25).83 (21) 2.13 (54) 1.89 (48).75 (19) Dimensions in inches (mm) PSC-19

19 Pressure sensing and control VP51 Programmable proportional pressure control valve G1/4, 1/4 NPT Fully programmable with on-board diagnostics Multi-option language display Password protection option at first level functionality Instant LED warning functions Application specific set-up Pressure output display; no gauge necessary High speed response Optional manifold mount utilizes the ISO Size 2 subbase Technical data Medium Compressed air filtered to 4 µm, non-lubricated Supply pressure 25 psig (14 bar) max. Output pressure psig ( - 1) Supply sensitivity <= 5 mbar between 16 and 9 psig (11 and 6 bar) supply Response time < 1 ms (from 1 to 9% of output pressure into a,1 litre load) Air consumption <.177 scfm (5 l/min) Total error Maximum error ± 1.45 psig (1 mbar) of total span (independent error includes the combined effect of nonlinearity, hysteresis, deadzone and repeatability) Ambient temperature -4 to 122 F (-2 to 5 C) Temperature effect Typically.4 psig (3 mbar)/ C for full scale and zero over operating range Degree of protection NEMA 4 in normal operation Vibration immunity <3% output shift for 3 g ~ 1 to 15 Hz Weight 1.76 lbs (.8 kg) Mounting position Any screw mounting or ISO 2 subbase manifold mount Materials Body: aluminum Lid and end cover: zinc diecast General information Control signal Output pressure Model Connection Output range psig (bar) units -1 V to 145 (1) VP511PK111H 1/4 NPT psig 4-2 ma to 145 (1) VP511PK411H 1/4 NPT psig -1 V to 145 (1) VP511BJ111H ISO G 1/4 bar 4-2 ma to 145 (1) VP511BJ411H ISO G 1/4 bar *To order the VP5 with interface for manifold mounting,indicate X in the 8th position of the part number. All units shipped with M12 five pin electrical connectors with interface for manifold mounting. Symbol P Electromagnetic compatibility The valve conforms to the EC requirements EN581 2 (emission) and EN582 2 (disturbance noise). For this specification shielded cables have to be used A D PSC-2

20 VP51 Programmable proportional pressure control valve G1/4, 1/4 NPT User functionality options Password protection Display set-up Speed set-up Monitor set-up Monitor output Local control Device database Factory defaults Electrical information Electromagnetic compatibility Display language Pressure units Offline set-up Online set-up fastest to 7 slowest Analogue... 1 V Hi = P2 > x psi Hi = P2 OK Manual control Max./min. ramp Max./min. stairs Read only data: unit specific Tag number Help display Restore factory defaults CE marked: conforms to EC requirements EN (1994) and EN (1995) ma or... 1 V factory set Electrical input signal Electrical power input 24 V d.c. ±25% (power consumption < 1 W) Output pressure feedback signal User configurable... 1V analog or Hi-Lo mode Characteristic curves Outlet Pressure in psig (bar) Forward Flow Characteristics Supply Pressure 16 psig (11bar) (1) 145 (9) 131 (8) 115 (7) 12 (6) 87 (5) 73 (4) 58 (3) 44 (2) 29 (1) (2) (4) (6) (8) (1) (12) (14) (16) Flow in SCFM (Nl/min) Outlet Pressure in psig (bar) Relief Flow Characteristics Supply Pressure 131 psig (9 bar) (9) 131 (8) 116 (7) 12 (6) (5) (4) (3) (2) (1) (-2) (-15) (-1) (-5) Flow SCFM (Nl/min) Instrument pin configuration M12 x 1 (5 pin) 1 4 Pin Designation Color* V d.c. supply brown/red 2 1 v/bar monitor output white Control signal (+ve) blue 4 Common (d.c. supply, signal and feedback return) black 5 Chassis (earth) grey/green/yellow General dimensions M 12 Accessories Designation Specification Type Connectors with cable M12 x 1.5 pin; 16 ft (5m) 5 x.34 mm M12 x 1.5 pin; 3 ft (1 m) 5 x.34 mm *Manifold Mounting Kit Interface plate, gasket, mounting screws 53ZZ5M For ISO 2 Manifold see website (21) 96 (25).96 (25).42 (11).35 (9) 4.47 (114) 5.21 (133) 1.38 (35) 2 **.79 (2) 1.1 (28) 2.16 (55)* 1.42 (36) * 2.6 (66) for manifold mounting version 1.97 (5).37 (7).79 (2) ** G1/4 optional 1/4 NPT PSC-21

21 Pressure sensing and control R-27 Series Manostat Precision Air Pressure Regulators High precision pressure regulators Suitable for dead end or flow applications Excellent long term stability Handwheel, lever, plunger or pilot operated Technical Data Medium: Dry, oil free air filter to 25 microns Operation: Two stage servo mechanized regulator with integral precision measuring capsule Mounting: Any position. Panel mounting or through mounting holes on the unit (lever, plunger and pilot versions) Port sizes: G 1/4 Output pressure ranges: See individual details Supply pressure: Minimum at least 2.9 psig (.2 bar) above output pressure. Maximum 145 psig (1 bar) Flow capacity: Up to 1.6 scfm (3 l/m) Hysteresis and repeatability: Less than.5% setting at midrange Sensitivity: Better than.3 mbar Air consumption: See individual details Ordering Information Output Pressure Air Consumption Weight Description Model Control Type Range psig (bar) scfm (l/m) lbs (kg) Standard regulator R Handwheel turns 2-25 (.14-2).1 (.3) 1.59 (.72) Standard regulator R Handwheel turns 2-6 (.14-4).2 (.6) 1.59 (.72) Standard regulator R Handwheel turns 2-12 (.14-8).4 (1.2) 1.59 (.72) Lever operated regulator R Lever control 125 Rotation 2-25 (.14-2).1 (.3) 1.59 (.72) Lever operated regulator R Lever control 125 Rotation 2-6 (.14-4).2 (.6) 1.59 (.72) Lever operated regulator R Lever control 125 Rotation 2-12 (.14-8).4 (1.2) 1.59 (.72) Plunger operated regulator R Plunger travel.65 (1.65) 2-6 (.14-4).2 (.6) 1.59 (.72) Plunger operated regulator R Plunger travel.65 (1.65) 2-12 (.14-8).4 (1.2) 1.59 (.72) Pilot operated relay R Pilot pressure signal 2-12 (.14-8).4 (1.2) 1.59 (.72) Pilot operated relay R Pilot pressure signal 2-12 (.14-8).4 (1.2) 1.59 (.72) with manual bias Handwheel controlled bias bias of up to 3 (2) Handwheel Operated 1.73 (44) 2.68 (68) Tension nut Mounting unit Bleed screw Inlet port Outlet port Exhaust.55 (14) Gauge port G 1/ (54) ø.45 (11.5) required for panel mounting 2.13 (54) Inlet port G 1/4 ISO Symbols PSC-22

22 All Dimensions in Inches (mm) Pilot Operated 2 mounting holes ø.37 (9.5) Inlet port 2.13 (54 ) 1.14 (29).51 (14) Signal Port 1/4" NPT 2.68 (59) 1.6 (27) Outlet port 1.26 (32) Bias adjustment (factory set).51 (13) 1.6 (27) Bleed screw Exhaust Typical Performance Characteristics OUTLET PRESSURE bar psig FORWARD FLOW CHARACTERISTICS 12 psig (8 bar) Supply 2 Gauge port G 1/4 Air connections G 1/ (59) scfm l/min Pilot Operated with Bias 2.68 (68) 2.36 (6) 1.1 (28) Inlet port 2 panel mounting holes tapped 2BA 1 deep Outlet port.71 (18) Signal port 1/8" BSP Bleed screw Exhaust OUTLET PRESSURE bar psig AIR FLOW RELIEF FLOW CHARACTERISTICS 12 psig (8 bar) Supply.55 (14) Gauge port G 1/4 Air connections G 1/ (54) scfm l/min AIR FLOW Plunger Operated 2.13 (54) Clevis fitting ø.75 (19) R16 Dome Fitting.31 (8).25 (6.4) Ball bearing ø.37 (9.5) Lever Operated Diaphragm Repair Kits Type Part number Units up to 25 psig R Units up to 6 psig R Units up to 12 psig R Tamperproof Nut R Wall Mounting Bracket 53-ABR-7.25 (6.4) Clevis with ø.13 (3.2) pin 2.68 (68) Inlet port Outlet port Bleed screws Exhaust 3.62 (92) 125 Adjustable zero and range stops Loosen nut to adjust zero and range stops 2.68 (68) 1.38 (35) Gauge port G 1/4 ø.28 (7) Air connections G 1/4 Inlet port Zero Range Outlet port 2.13 (54) 1.38 (35) 3.27 (83) 4.2 (12) 1.97 (5) 2.99 (76) 3.43 (87) 4.13 (15) 4 fixing holes ø.25 (6.3) Air connections Exhaust Bleed screws G 1/4 PSC-23

23 Pressure sensing and control Additional Valve Products Type 68 P/I Transmitter type 68 Type 68 converts pneumatic pressure into a 4-2 ma electrical signal for uses with data loggers or PLC controls. The unit is suitable for DIN rail or line mounting and requires only a non-critical DC power supply. Optional IP65 weatherproof versions are available. Type 421 Compact failsafe rail mount I/P converter A rugged, electronic I/P converter designed for high density rail or manifold mounting, at a spacing of only 1" (25mm) Advanced electronic control using surface mount electronics and a precision pressure transducer and offers excellent performance characteristics Employs a high sensitivity microminiature Reedex valve for pressure control Great reliability, long life, freedom from vibration effects, and are significantly less prone to mechanical derangement than older conventional designs Can be mounted on DIN rail, surface mounted, or mounted onto a high density manifold Type 422 Failfreeze Electronic Converter A major advance in I/P converter design, offering failfreeze in addition to conventional I/P features Advanced electronic control and a precision pressure transducer to achieve outstanding performance Intended for field application in which rugged construction, vibration immunity, weatherproofing and reliability are essential, together with the enhanced system safety gained from its failfreeze characteristic Two wire operation from a 4-2mA control signal with output pressures up to 12 psig (8 bar) as standard PSC-24

24 Type 423 Failsafe Electronic I/P Converter For field mount process control applications State-of-art electronics, precision internal pressure measurement, digital pressure control and excellent environmental and vibration characteristics Rugged high sensitivity Reedex Valve for pressure control Extreme reliability, freedom from vibration effect and long life, together with very low air consumption and hysteresis. Allows an output capacity of up to 1 scfm, so that no volume booster is necessary for high flow applications such as large valves Type 14 Electronic I/P Converter For service in demanding process control applications, the Type 14 is used to convert a 4-2 ma control current to a 3-15 psi pneumatic signal for operating a control valve actuator. The internal closed-loop control electronics assure high resolution and long-term accuracy. Fully encapsulated circuit boards provide added environmental protection. Type 14 is available in Intrinsically Safe and Explosion proof versions with ATEX, CSA and FM approvals. PSC-25