Groove Mitigation and Plans

Size: px
Start display at page:

Download "Groove Mitigation and Plans"

Transcription

1 Groove Mitigation and Plans M. Pivi and L. Wang (SLAC) Y. Suetsugu, H. Fukuma (KEK) M. Palmer (Cornell) G. Arduini, E. Chapochnikova (CERN) AEC09 CERN October 2009

2 Grooves as mitigation Grooves strongly damp electron multiplication by trapping mechanism. Most efficient schemes are: Rectangular shape in field-free sections Triangular shape in magnets Showing here: Early SEY measurements on test samples, 2006 PEP-II groove chambers, 2007 KEKB groove in wiggler, 2008 CesrTA groove in chicane, 2009

3 Groove samples SEY measurements, SLAC M.Pivi and G. Stupakov, SLAC Tested a variety of grooved samples with several different geometries PEP-II chamber test samples 1 mm Special surface profile design, Cu OFHC. EDM wire cutting. Groove: 0.8mm depth, 0.35mm step, 0.05mm thickness. Un-coated copper sample SEY < 0.8. Smaller SEY~0.6 with deeper grooves Ref: A. Krasnov LHC-Proj-Rep-617

4 Design - Groove Extrusions - SLAC FAN EVENTUALLY HITS BOTTOM OF SLOT FOR FULL SR STRIKE LIGHT PASSES THRU SLOTS BETW FINS BECAUSE FAN IS THICKER THAN FIN FIN TIPS= I.D. OF CHAM FAN HITS HERE FIRST M. Pivi et al, SLAC Linear Collider R&D: Built Groove chambers by Al extrusion, TiN coated and installed in straight section PEP-II LER for ILC tests.

5 Groove Chambers in PEP-II 4 chambers alternating groove and standard (flat or smooth) chambers in PEP-II beam line, straight section. Grooved chamber Flat chamber e+ Standard (flat) chambers installed as reference. All chambers TiN coated Electron detectors

6 Groove Chambers in PEP-II Groove chambers in field-free section, a factor ~20 lower e- cloud current All 4 chambers re-deployed to CesrTA

7 Grooves in dipole magnet Grooves located on upper and lower side of chamber where e- cloud develops. Include diagnostics. TiN-coated Re-deployed to CesrTA Grooves + TiN chamber best performances in ongoing chicane tests M. Pivi and L. Wang design, SLAC

8 Dipole Mitigation Comparisons Current scan in L3 Chicane, 1x45 e+, 14ns, 5GeV Note: Al signal is divided by 20 to show on the same scale Grooved chamber has 5mm deep 20 triangular grooves with TiN coating Performance: TiN+Grooves significantly better than TiN alone Both TiN and grooves significantly outperform the bare Al surface, as expected CesrTA Mitigation Studies: LCWA09 M. Palmer Cornell

9 4ns Chicane B-field Scans 1x45x1 ma, 4ns, 5GeV, e+ Resonance structure Plots show Central collector (near beam axis) Collectors near edge of vacuum chamber 17 collectors in each RFA Grooves + TiN Al TiN M. Palmer Cornell 9

10 Grooves tests in KEKB Groove and smooth inserts coated with TiN 5mm groove insert (Left) TiN-coated, manufactured by SLAC Smooth insert (Right) used as reference Swapped at same location in KEKB wiggler Located on one side of chamber opposite to collector M. Pivi, L. Wang (SLAC) Y. Suetsugu and H. Fukuma (KEK)

11 Vr = 0 V Electron Currents 1585 bunches (B s ~ 6 ns) ~1600 ma Y. Suetsugu and H. Fukuma (KEK), M. Pivi, L. Wang (SLAC)

12 Smaller Grooves New smaller ~2mm groove SLAC-KEK design. Ongoing tests at KEKB. Sharpness of groove geometry can be a manufacturing challenge due to demanding e- cloud tolerances Y. Suetsugu, H. Fukuma KEK, M. Pivi, L. Wang SLAC

13 Groove Tests in the SPS Planning for tests in SPS dedicated area: Depth of groove limited to 1 mm due to vacuum chamber aperture requirements. Stainless steel insertion Tight tolerances on roundness of groove tips and valleys: < 100um. Groove on one side of test chamber only Insertion in existing liner or modified liner

14 Groove Tests in the SPS SPS liner for e- cloud tests

15 Liner for SPS tests Groove Tests in the SPS Sep 2009

16 Groove Tests in the SPS St st. Groove insert bolt to liner Variable incursion into chamber, actually 1.5mm

17 Extruded aluminum insertion Aluminum triangular groove, SLAC. Depth 1.9mm, Opening angle 20 o, radius top 95um, radius valley 144um Tip Tip Valley 2 δ 0 = 1.5 0,He ig ht= 1.9 m m, α= Back-up: 1.9mm aluminum + coating grooves (pictures above), manufactured at SLAC. Extruded aluminum groove. SEY Fla t surfa ce r= m m,b= 2 Te sla r= m m,b= 0.2T esla r= m m,b= 2 Te sla r= m m,b= 0.2T esla averag e, B= 2 Tes la Lanfa Wang, SLAC En ergy ( ev ) April 2008 Mauro Pivi - SLAC

18 Effect of triangular grooves on Impedance Impedance enhancement factor for the triangular grooved surface with round tips. Note that this is valid for frequencies ω such that c/ ω >> W; for example, for W~3mm this means ν<6e11 Hz. ref. [L. Wang et al. FRPMS079, Proceedings of PAC07.] L. Wang et al. SLAC

19 Linear Collider R&D - Electron Cloud Working Group Charges To evaluate electron cloud mitigation techniques, simulations and code benchmarking for the AD&I option. In particular, evaluate the differences between mitigations as grooves clearing electrodes, coating (TiN, TiZrV NEG and amorphous Carbon) regarding their feasibility, effectiveness, impact on the vacuum system, on the beam impedance and on costs, for different regions of the ILC DR as drifts, arc magnets and wigglers.

20 Working Group Charges Mitigation techniques might be different for different regions of the damping ring. To recommend a baseline solution along with alternate solutions for the electron cloud mitigations in the 6.4km Damping Ring.

21 Working Group Charges Furthermore, evaluate: The proposal and options to reduce the DR circumference to 3.2 km. The upgrade potential from 6ns to 3ns bunch spacing in a 3km DR, immediately identified as bottleneck. The current limits due to e-cloud for the 3.2 km DR.

22 Deliverable Recommendation for the baseline and alternate solutions for the electron cloud mitigation in various regions of the ILC Positron Damping Ring.

23 Recommendation for mitigation table DR element % ring Antechamber need DRIFT in STRAIGHT DRIFT in ARC Coating Additional Mitigation Remarks 33 No NEG Solenoid Grooves 56 Downstream of BEND only NEG Solenoid Grooves BEND 7 Yes TiN Grooves WIGG 3 Yes TiN Electrodes QUAD 1 Downstream BEND / WIGG TiN Grooves Preliminary table to be completed as input for Technical Design Phase. Goal is to turn all Red colors to Green as input for the recommendation. Other mitigations under development (carbon coating CERN/CesrTA)

24 Report Document A document produced by the working group by FY10 including the research work, a clear set of criteria for the recommendation and the recommendation itself.

25 Report Document Recommendation on electron cloud mitigations for the ILC DR Introduction 5 Request from AAP 5 Working Group Charges and Deliverables 5 Introduction Electron Cloud effect 10 [Zimmermann / Furman] Mitigations description Solenoid 10 [Seeman] TiN coating10 [Suetsugu] Carbon coating 10 [Calatroni / Palmer] NEG coating 10 [Malishev] Grooves and Impedance 10 [Pivi] Clearing Electrodes and Impedance 10 [Suetsugu] Feedback system 10 [J. Fox] Conditioning 10 [Pivi / Suetsugu] Other mitigations (more or less mature) 8 Overall Experience at CesrTA 20 [Palmer] Overall Experience at PEP-II 20 [Pivi] Overall Experience at KEK-B 20 [Oide] Overall Experience at SPS 20 [Rumolo / Arduini]

26 Report Document ILC Damping Ring 15 Layout and parameters 8 Photon and Photoelectron Production 10 Simulation build-up 20 Simulation single-bunch instability 20 Impedance of mitigations 15 Integrate CesrTA results to DR 20 [Palmer] Process for mitigations recommendation 20 Set of criteria for a decision 20 External Reviews and Meetings 20 Mitigations cost 5 [Palmer] Recommendation for Mitigations in the ILC DR 5 Summary 5 [Pivi / Guiducci] [Dugan] [Demma / Furman] [Pivi] [Suetsugu / Bane]

27 Summary Overall grooves had excellent performances with e- cloud reduction in field free, dipole and wiggler sections of PEP-II, KEK-B and CesrTA. Manufacturing groove insert for SPS tests. mm size grooves manufacturing challenge. Implementation in existing machines is challenging. Looking at reducing groove depth to ~mm in long structures for Linear Colliders Damping Ring. Recommendation for electron cloud mitigations in ILC DR.

28 Wakefield simulations PEP-II design MAFIA simulations (A. Novokhatski) indicate that wake fields are not excited during the beam passage in PEP-II design. Very small losses at transition estimated 1.5E-04 V/pC. Quoting A. Novokhatski: actually, grooves may help damping the propagation of Higher Order Modes down the beam pipe (need of simulations) Power losses due to image charge are contained (ex. PEP-II, dp/ds=1w/cm).

Central Region Group Status and Positron Region

Central Region Group Status and Positron Region Central Region Group Status and Positron Region K. Yokoya 2016.9.14. Posipol2016, LAL 2016/9/14 Posipol2016 1 Issues Discussed in CRWG Positron-related 10Hz operation Auxiliary positron source (APS) Positron

More information

PETRA III Damping Sections

PETRA III Damping Sections PETRA III Damping Sections Markus Tischer, HASYLAB 05.05.06 Damping wiggler sections BINP / DESY cooperation on Damping wiggler Vacuum system Absorber M. Tischer PETRA III Damping Sections (MAC meeting,

More information

Vacuum pumps for the ESRF EBS project Michael Hahn

Vacuum pumps for the ESRF EBS project Michael Hahn 3 rd Rencontres Nationales DU RESEAU TECHNOLOGIES DU VIDE SEVRIER, 10 13 October 2016 Vacuum pumps for the ESRF EBS project Michael Hahn On behalf of the EBS Accelerator Project Team OUTLINE Project definition

More information

Major Upgrade Activity of the PLS in PAL: PLS-II

Major Upgrade Activity of the PLS in PAL: PLS-II Major Upgrade Activity of the PLS in PAL: PLS-II S. H. Nam on behalf of the PAL staff Pohang Accelerator Laboratory (PAL) POSTECH May 7, 2009 Particle Accelerator Conference 2009 Vancouver, British Columbia,

More information

TDIS pressure profile simulations after LS2

TDIS pressure profile simulations after LS2 CERN-ACC-NOTE 16 October 2018 patricia.ribes.metidieri@cern.ch christina.yin.vallgren@cern.ch TDIS pressure profile simulations after LS2 P. Ribes Metidieri, C. Yin Vallgren, G. Skripka, G. Iadarola, G.

More information

ILC. CFS update for Europe (CERN): Cross Sections 3d Layout and BDS tunnel diameters CERN Resources. LCWS10 and ILC10 - Beijing

ILC. CFS update for Europe (CERN): Cross Sections 3d Layout and BDS tunnel diameters CERN Resources. LCWS10 and ILC10 - Beijing ILC CFS update for Europe (CERN): Cross Sections 3d Layout and BDS tunnel diameters CERN Resources John Osborne March 2010 LCWS10 and ILC10 - Beijing Cross section for Europe (CERN) 5.2m diameter for Kly

More information

Girder Alignment Plan

Girder Alignment Plan LCLS-TN-08-3 Girder Alignment Plan Zachary Wolf, Robert Ruland, Catherine LeCocq, Eric Lundahl, Yurii Levashov, Ed Reese, Carl Rago, Ben Poling, Donald Schafer, Heinz-Dieter Nuhn, Uli Wienands SLAC March

More information

Solenoid Magnets for the Front End of a Neutrino Factory

Solenoid Magnets for the Front End of a Neutrino Factory Solenoid Magnets for the Front End of a Neutrino Factory M.A. Green and S.S. Yu Lawrence Berkeley National Laboratory, Berkeley CA 94720 J.R. Miller and S. Prestemon National High Magnetic Field Laboratory,

More information

ALTERNATIVE BUNCH FILLING SCHEME FOR THE LHC - PART II (INJECTOR COMPLEX)

ALTERNATIVE BUNCH FILLING SCHEME FOR THE LHC - PART II (INJECTOR COMPLEX) ALTERNATIVE BUNCH FILLING SCHEME FOR THE LHC - PART II (INJECTOR COMPLEX) G. Arduini,, W. Herr, E. Métral and T. Pieloni Part I (LHC) by Werner Introduction and motivation for the injector complex Review

More information

STATUS OF DESIGN WORK TOWARDS AN ELECTRON COOLER FOR HESR*

STATUS OF DESIGN WORK TOWARDS AN ELECTRON COOLER FOR HESR* STATUS OF DESIGN WORK TOWARDS AN ELECTRON COOLER FOR HESR* Björn Gålnander#, Torsten Bergmark, Olle Byström, Stefan Johnson, Tomas Johnson, Tor Lofnes, Gunnar Norman, Tord Peterson, Karin Rathsman, Dag

More information

Progress Towards Doubling the Beam Power at Fermilab s Accelerator Complex

Progress Towards Doubling the Beam Power at Fermilab s Accelerator Complex Progress Towards Doubling the Beam Power at Fermilab s Accelerator Complex June 17, 2014 Ioanis Kourbanis FERMILAB Outline Introduction. Review of past MI high power operations. Plan of doubling the MI

More information

Motor Technologies Motor Sizing 101

Motor Technologies Motor Sizing 101 Motor Technologies Motor Sizing 101 TN-2003 REV 161221 PURPOSE This technical note addresses basic motor sizing with simple calculations that can be done to generally size any motor application. It will

More information

M. A. Green, and S. Yu Lawrence Berkeley National Laboratory, Berkeley CA 94720, USA

M. A. Green, and S. Yu Lawrence Berkeley National Laboratory, Berkeley CA 94720, USA LBNL-48445 SCMAG-749 SUPERCONDUCTING MAGNETS FOR INDUCTION LINAC PHASE-ROTATION IN A NEUTRINO FACTORY M. A. Green, and S. Yu Lawrence Berkeley National Laboratory, Berkeley CA 94720, USA ABSTRACT The neutrino

More information

Use of Flow Network Modeling for the Design of an Intricate Cooling Manifold

Use of Flow Network Modeling for the Design of an Intricate Cooling Manifold Use of Flow Network Modeling for the Design of an Intricate Cooling Manifold Neeta Verma Teradyne, Inc. 880 Fox Lane San Jose, CA 94086 neeta.verma@teradyne.com ABSTRACT The automatic test equipment designed

More information

The ATLAS Detector at the Large Hadron Collider. Peter Krieger IPP/University of Toronto

The ATLAS Detector at the Large Hadron Collider. Peter Krieger IPP/University of Toronto The ATLAS Detector at the Large Hadron Collider Peter Krieger IPP/University of Toronto The ATLAS Detector at the Large Hadron Collider Peter Krieger IPP/Toronto CAP Congress, Winnipeg 2004 2 Peter Krieger

More information

Study of the impact of the remote alignment in the vacuum system

Study of the impact of the remote alignment in the vacuum system Study of the impact of the remote alignment in the vacuum system R. Rego, V. Baglin, J. Hansen CERN, 24 th September 2018 EDMS: 2027649 Outline 1. Introduction 2. Inner triplet area 3. TAXN-D2 area 4.

More information

arxiv: v1 [physics.ins-det] 1 Jul 2014

arxiv: v1 [physics.ins-det] 1 Jul 2014 Construction and test of high precision drift-tube (smdt) chambers for the ATLAS muon spectrometer arxiv:1407.085v1 [physics.ins-det] 1 Jul 014 Sebastian NOWAK E-mail: nowak@mppmu.mpg.de Oliver KORTNER

More information

Schematic design of the cryogenic baffles

Schematic design of the cryogenic baffles JGW- T12 01096- v1 KAGRA June 2 nd 2012 Schematic design of the cryogenic baffles Riccardo DeSalvo Distribution of this document: Public This is an internal working note of the KAGRA Large-scale Cryogenic

More information

Cover Plate Closures. Gaskets for Self-Sealing Cover Plate Closures. Graphite Cover Plate Gaskets. Double-Cone Gaskets.

Cover Plate Closures. Gaskets for Self-Sealing Cover Plate Closures. Graphite Cover Plate Gaskets. Double-Cone Gaskets. Gaskets for Self-Sealing Cover Plate Closures Graphite Cover Plate Gaskets Double-Cone Gaskets Delta-Gaskets Gaskets for Self-Sealing Cover Plate Closures Gaskets for Self-Sealing Cover Plate Closures

More information

All-SiC Module for Mega-Solar Power Conditioner

All-SiC Module for Mega-Solar Power Conditioner All-SiC Module for Mega-Solar Power Conditioner NASHIDA, Norihiro * NAKAMURA, Hideyo * IWAMOTO, Susumu A B S T R A C T An all-sic module for mega-solar power conditioners has been developed. The structure

More information

Experiences from First Top-Off Injection At The Stanford Synchrotron Radiation Lightsource

Experiences from First Top-Off Injection At The Stanford Synchrotron Radiation Lightsource Experiences from First Top-Off Injection At The Stanford Synchrotron Radiation Lightsource Johannes Bauer, James Liu, Alyssa Prinz, Sayed Rokni Radiation Protection Department SLAC National Accelerator

More information

Arcing prevention by dry clean optimization at Shallow Trench Isolation (STI) Etch in AMAT MxP by use of plasma parameters

Arcing prevention by dry clean optimization at Shallow Trench Isolation (STI) Etch in AMAT MxP by use of plasma parameters Page 1 Arcing prevention by dry clean optimization at Shallow Trench Isolation (STI) Etch in AMAT MxP by use of plasma parameters www.tu-cottbus.de www.infineon.com 2 nd AEC/ Conference Europe, April 18

More information

KAON Factory Alignment

KAON Factory Alignment 93 KAON Factory Alignment George S. Clark and David G. Martin* TRIUMF, 4004 Wesbrook Mall, Vancouver, Canada TRIUMF is Canada's national subatomic research facility. Located in Vancouver, Canada, the TRIUMF

More information

Fueling System Proposal for KSTAR

Fueling System Proposal for KSTAR Fueling System Proposal for KSTAR D.A. Rasmussen, L.R. Baylor, S. K. Combs, M.J. Cole, P.B. Parks* Oak Ridge National Laboratory KSTAR fueling system parameters Parameter Gas Fueling System Pellet Fueling

More information

The CU Beam Test at CERN Status Report and highlights from workshop II

The CU Beam Test at CERN Status Report and highlights from workshop II The CU Beam Test at CERN Status Report and highlights from workshop II Luca Latronico luca.latronico@pi.infn.it LAT C&A Meeting May 22 2006 GLAST LAT Project LAT C&A Meeting 5/22/2006 Beam Test Schedule

More information

Precision Alignment of Multipoles on a Girder for NSLS-II*

Precision Alignment of Multipoles on a Girder for NSLS-II* Precision Alignment of Multipoles on a Girder for NSLS-II* Animesh Jain Superconducting Magnet Division Brookhaven National Laboratory, Upton, NY 11973 17 th International Magnetic Measurement Workshop

More information

Present and Future Cryogenics at Cornell

Present and Future Cryogenics at Cornell QuickTime and a TIFF (Uncompressed) decompressor are needed to see this picture. QuickTime and a TIFF (Uncompressed) decompressor are needed to see this picture. QuickTime and a TIFF (Uncompressed) decompressor

More information

ALIGNMENT AND STABILITY OF THE TPS STORAGE RING AUTO- TUNING GIRDER SYSTEM

ALIGNMENT AND STABILITY OF THE TPS STORAGE RING AUTO- TUNING GIRDER SYSTEM ALIGNMENT AND STABILITY OF THE TPS STORAGE RING AUTO- TUNING GIRDER SYSTEM T.C. Tseng, W.Y. Lai, C.J. Lin, H.S. Wang, M.L. Chen, H.C. Ho, S.Y. Perng, K.H. Hsu, D.G. Huang, P.S. Chuang, C.W. Tsai, C.K.

More information

Development of Noise-reducing Wheel

Development of Noise-reducing Wheel Introduction of new technologies Development of Noise-reducing Wheel Development of Noise-reducing Wheel Youichi KAMIYAMA* Hisamitsu TAKAGI* Katsushi ISHII* Mikio KASHIWAI** ABSTRACT Tire cavity noise

More information

M. Modena - CERN. 18 th ATF2 Project Meeting, 26 Feb. 2015, LAPP, Annecy-F

M. Modena - CERN. 18 th ATF2 Project Meeting, 26 Feb. 2015, LAPP, Annecy-F M. Modena - CERN 18 th ATF2 Project Meeting, 26 Feb. 2015, LAPP, Annecy-F 1 After the CERN/ATF2 Midterm Collaboration proposal presented in May 2014 and its approval on August 2014, we focus on the final

More information

Low Beta Cryomodule Development at Fermilab. Tom Nicol March 2, 2011

Low Beta Cryomodule Development at Fermilab. Tom Nicol March 2, 2011 Low Beta Cryomodule Development at Fermilab Tom Nicol March 2, 2011 Concepts of SC CW 3GeV, 1mA Linac H - gun RFQ MEBT SSR0 SSR1 SSR2 β=0.6 β=0.9 ILC RT (~15m) 325 MHz 2.5-160 MeV 650 MHz 0.16-2 GeV 1.3

More information

XML Description of Magnet Geometry

XML Description of Magnet Geometry XML Description of Magnet Geometry Version 1.1 Galina Pakhlova (ITEP, Moscow) June 4, 2002 1 Introduction The XML description of the magnet geometry is based on the recent update of the engineering drawings

More information

Electron Beam Alignment Strategy in the LCLS Undulators

Electron Beam Alignment Strategy in the LCLS Undulators Electron Beam Alignment Strategy in the LCLS Undulators Undulator Overview Tolerances Controls Monitoring Alignment Diagnostics System Task Scheduling August 31, 2006 Collaborators: Georg L. Gassner Paul

More information

CAE Analysis of Passenger Airbag Bursting through Instrumental Panel Based on Corpuscular Particle Method

CAE Analysis of Passenger Airbag Bursting through Instrumental Panel Based on Corpuscular Particle Method CAE Analysis of Passenger Airbag Bursting through Instrumental Panel Based on Corpuscular Particle Method Feng Yang, Matthew Beadle Jaguar Land Rover 1 Background Passenger airbag (PAB) has been widely

More information

GENERATOR SEAL OIL SYSTEM

GENERATOR SEAL OIL SYSTEM GENERATOR SEAL OIL SYSTEM Eskom power utility utilized Flownex SE simulation capabilities to mitigate system shutdowns caused by generator hydrogen (H 2 ) seal ring failures. Engineers modelled the hydrogen

More information

PHYSICAL MODEL TESTS OF ICE PASSAGE AT LOCKS

PHYSICAL MODEL TESTS OF ICE PASSAGE AT LOCKS Ice in the Environment: Proceedings of the 16th IAHR International Symposium on Ice Dunedin, New Zealand, 2nd 6th December 22 International Association of Hydraulic Engineering and Research PHYSICAL MODEL

More information

ONICON Insertion Turbine Flow Meters Single Turbine vs. Dual Turbine Selection Criteria

ONICON Insertion Turbine Flow Meters Single Turbine vs. Dual Turbine Selection Criteria ONICON Insertion Turbine s Single Turbine vs. Dual Turbine Selection Criteria The purpose of this guide is to provide customers and specifying engineers with information about how to choose between ONICON's

More information

Straw Detectors for the Large Hadron Collider. Dirk Wiedner

Straw Detectors for the Large Hadron Collider. Dirk Wiedner Straw Detectors for the Large Hadron Collider 1 B-Mesons Bd π π? B-Mesons properties? Charge parity symmetry violation? 2 Proton-Proton Collision Bd proton LHC Start 2007 π proton 14 TeV π? B-Mesons properties?

More information

Multi Body Dynamic Analysis of Slider Crank Mechanism to Study the effect of Cylinder Offset

Multi Body Dynamic Analysis of Slider Crank Mechanism to Study the effect of Cylinder Offset Multi Body Dynamic Analysis of Slider Crank Mechanism to Study the effect of Cylinder Offset Vikas Kumar Agarwal Deputy Manager Mahindra Two Wheelers Ltd. MIDC Chinchwad Pune 411019 India Abbreviations:

More information

RPC Upgrade for the CMS experiment

RPC Upgrade for the CMS experiment RPC Upgrade for the CMS experiment L. M. Pant Nuclear Physics Division Bhabha Atomic Research Centre, Mumbai 1 Restoration of the full TDR, RE4 ( ) Present experiment runs with 3 endcaps 2 one of the end

More information

EFFECT OF SURFACE ROUGHNESS ON PERFORMANCE OF WIND TURBINE

EFFECT OF SURFACE ROUGHNESS ON PERFORMANCE OF WIND TURBINE Chapter-5 EFFECT OF SURFACE ROUGHNESS ON PERFORMANCE OF WIND TURBINE 5.1 Introduction The development of modern airfoil, for their use in wind turbines was initiated in the year 1980. The requirements

More information

Status of the DARHT 2 nd Axis Accelerator at Los Alamos National Laboratory

Status of the DARHT 2 nd Axis Accelerator at Los Alamos National Laboratory Status of the DARHT 2 nd Axis Accelerator at Los Alamos National Laboratory R.D. Scarpetti, S. Nath, J. Barraza, C. A. Ekdahl, E. Jacquez, K. Nielsen, J. Seitz Los Alamos National Laboratory, Los Alamos,

More information

Effectiveness of ECP Brakes in Reducing the Risks Associated with HHFT Trains

Effectiveness of ECP Brakes in Reducing the Risks Associated with HHFT Trains Effectiveness of ECP Brakes in Reducing the Risks Associated with HHFT Trains Presented To The National Academy of Sciences Review Committee October 14, 2016 Slide 1 1 Agenda Background leading to HM-251

More information

Summary of Working Group C: Injection, Extraction, Accelerator Systems

Summary of Working Group C: Injection, Extraction, Accelerator Systems Summary of Working Group C: Injection, Extraction, Accelerator Systems D. Johnson and S. Cousineau ICFA HB2010 Sept 27 Oct. 1 Morschach, Switzerland Outline of Summary 1. Essence of the Work Group New

More information

Modeling and Optimization of a Linear Electromagnetic Piston Pump

Modeling and Optimization of a Linear Electromagnetic Piston Pump Fluid Power Innovation & Research Conference Minneapolis, MN October 10 12, 2016 ing and Optimization of a Linear Electromagnetic Piston Pump Paul Hogan, MS Student Mechanical Engineering, University of

More information

Overview of Magnetic Measurement Activities at SLAC National Accelerator Lab (SLAC)

Overview of Magnetic Measurement Activities at SLAC National Accelerator Lab (SLAC) Overview of Magnetic Measurement Activities at SLAC National Accelerator Lab (SLAC) Scott Anderson, Ralph Colon, Scott Jansson, Dave Jensen, Yuri Levashov, Zachary Wolf 17 th International Magnetic Measurement

More information

STEALTH INTERNATIONAL INC. DESIGN REPORT #1001 IBC ENERGY DISSIPATING VALVE FLOW TESTING OF 12 VALVE

STEALTH INTERNATIONAL INC. DESIGN REPORT #1001 IBC ENERGY DISSIPATING VALVE FLOW TESTING OF 12 VALVE STEALTH INTERNATIONAL INC. DESIGN REPORT #1001 IBC ENERGY DISSIPATING VALVE FLOW TESTING OF 12 VALVE 2 This report will discuss the results obtained from flow testing of a 12 IBC valve at Alden Research

More information

Shaft Grounding Rings. Protecting VFD Driven Motors from Bearing Currents

Shaft Grounding Rings. Protecting VFD Driven Motors from Bearing Currents Shaft Grounding Rings Protecting VFD Driven Motors from Bearing Currents Variable Frequency Drives and Electric Induction Motors When pulse width modulation (PWM) Variable Frequency Drives (VFDs) were

More information

This short paper describes a novel approach to determine the state of health of a LiFP (LiFePO 4

This short paper describes a novel approach to determine the state of health of a LiFP (LiFePO 4 Impedance Modeling of Li Batteries for Determination of State of Charge and State of Health SA100 Introduction Li-Ion batteries and their derivatives are being used in ever increasing and demanding applications.

More information

White Paper. Improving Accuracy and Precision in Crude Oil Boiling Point Distribution Analysis. Introduction. Background Information

White Paper. Improving Accuracy and Precision in Crude Oil Boiling Point Distribution Analysis. Introduction. Background Information Improving Accuracy and Precision in Crude Oil Boiling Point Distribution Analysis. Abstract High Temperature Simulated Distillation (High Temp SIMDIS) is one of the most frequently used techniques to determine

More information

Continuing Research and Development of Linac and Final Doublet Girder Movers

Continuing Research and Development of Linac and Final Doublet Girder Movers Continuing Research and Development of Linac and Final Doublet Girder Movers Classification: Accelerator Science Institution and Personnel requesting funding: Colorado State University David W. Warner,

More information

MagneMotion Maglev Demonstration on ODU Guideway

MagneMotion Maglev Demonstration on ODU Guideway MagneMotion Maglev Demonstration on ODU Guideway SUMMARY MagneMotion and Old Dominion University undertook a cooperative agreement to demonstrate the MagneMotion M3 urban maglev technology on an existing

More information

Growing Charging Station Networks with Trajectory Data Analytics

Growing Charging Station Networks with Trajectory Data Analytics Growing Charging Station Networks with Trajectory Data Analytics Yanhua Li 1, Jun Luo 2, Chi-Yin Chow 3, Kam-Lam Chan 3, Ye Ding 4, and Fan Zhang 2 1WPI, CAS 2, CityU 3, HKUST 4 Contact: yli15@wpi.edu

More information

CBM Engineering. Mechanical Concept, design and prototyping of the STS for the CBM Experiment at FAIR

CBM Engineering. Mechanical Concept, design and prototyping of the STS for the CBM Experiment at FAIR 03.07.2017 Oleg Vasylyev Concept, design and prototyping of the STS ENMD CBM Engineering Mechanical Concept, design and prototyping of the STS for the CBM Experiment at FAIR Oleg Vasylyev, GSI Helmholtz

More information

SFM/TFM Power Integrity Guidelines Samtec SFM/TFM Series Measurement and Simulation Data

SFM/TFM Power Integrity Guidelines Samtec SFM/TFM Series Measurement and Simulation Data SFM/TFM Power Integrity Guidelines Samtec SFM/TFM Series Measurement and Simulation Data Scott McMorrow, Director of Engineering Page 1 SFM/TFM Power Integrity Guidelines Modeled Section SFM Board TFM

More information

AMBR* Engine for Science Missions

AMBR* Engine for Science Missions AMBR* Engine for Science Missions NASA In Space Propulsion Technology (ISPT) Program *Advanced Material Bipropellant Rocket (AMBR) April 2010 AMBR Status Information Outline Overview Objectives Benefits

More information

Carlo J. Bocchetta ESLS XIX Aarhus, Denmark November Status of Solaris

Carlo J. Bocchetta ESLS XIX Aarhus, Denmark November Status of Solaris Carlo J. Bocchetta ESLS XIX Aarhus, Denmark 23-24 November 2011 Status of Solaris What is Solaris? Polish Synchrotron Radiation Facility in Krakow Replica of the MAX IV 1.5 GeV Storage Ring and parts of

More information

Machine Design Optimization Based on Finite Element Analysis using

Machine Design Optimization Based on Finite Element Analysis using Machine Design Optimization Based on Finite Element Analysis using High-Throughput Computing Wenying Jiang T.M. Jahns T.A. Lipo WEMPEC Y. Suzuki W. Taylor. JSOL Corp. UW-Madison, CS Dept. 07/10/2014 2014

More information

Supporting Information. For. Evaluating the Potential of Platooning in. Lowering the Required Performance Metrics of

Supporting Information. For. Evaluating the Potential of Platooning in. Lowering the Required Performance Metrics of Supporting Information For Evaluating the Potential of Platooning in Lowering the Required Performance Metrics of Li-ion Batteries to Enable Practical Electric Semi-Trucks Matthew Guttenberg, Shashank

More information

Influence of Cylinder Bore Volume on Pressure Pulsations in a Hermetic Reciprocating Compressor

Influence of Cylinder Bore Volume on Pressure Pulsations in a Hermetic Reciprocating Compressor Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2014 Influence of Cylinder Bore Volume on Pressure Pulsations in a Hermetic Reciprocating

More information

Integrated 1D-MultiD Fluid Dynamic Models for the Simulation of I.C.E. Intake and Exhaust Systems

Integrated 1D-MultiD Fluid Dynamic Models for the Simulation of I.C.E. Intake and Exhaust Systems Integrated -MultiD Fluid Dynamic Models for the Simulation of I.C.E. Intake and Exhaust Systems G. Montenegro, A. Onorati, F. Piscaglia, G. D Errico Politecnico di Milano, Dipartimento di Energetica, Italy

More information

Continuing Research and Development of Linac and Final Doublet Girder Movers

Continuing Research and Development of Linac and Final Doublet Girder Movers Continuing Research and Development of Linac and Final Doublet Girder Movers Classification: Accelerator Science Institution and Personnel requesting funding: Colorado State University David W. Warner,

More information

Linear Induction Motor (LIMO) Modular Test Bed for Various Applications

Linear Induction Motor (LIMO) Modular Test Bed for Various Applications Linear Induction Motor (LIMO) Modular Test Bed for Various Applications ECE 4901 Senior Design I Fall 2013 Fall Project Report Team 190 Members: David Hackney Jonathan Rarey Julio Yela Faculty Advisor

More information

Proposal for Adoption Speed Trace Violations / Drive Trace Index

Proposal for Adoption Speed Trace Violations / Drive Trace Index WLTP-12-xxe Proposal for Adoption Speed Trace Violations / Drive Trace Index Prepared by WLTP Trace Index Task Force 18 th September 2015 Missions of the TF Seek the effective and essential way how to

More information

Electromagnetic Fully Flexible Valve Actuator

Electromagnetic Fully Flexible Valve Actuator Electromagnetic Fully Flexible Valve Actuator A traditional cam drive train, shown in Figure 1, acts on the valve stems to open and close the valves. As the crankshaft drives the camshaft through gears

More information

# Gun Tube Wear Reduction for 105 mm Artillery

# Gun Tube Wear Reduction for 105 mm Artillery #10595 - Gun Tube Wear Reduction for 105 mm Artillery May 18 th, 2010 Thomas Boncompain Project engineer 450-581-3080 ext. 8507 PRESENTATION SUMMARY Initial Problem Gun Wear Mechanism Technical Approach

More information

Note on preliminary cost estimate for an integrated tracker for the STAR experiment at RHIC

Note on preliminary cost estimate for an integrated tracker for the STAR experiment at RHIC Note on preliminary cost estimate for an integrated tracker for the STAR experiment at RHIC Gerrit van Nieuwenhuizen (MIT), Ernst Sichtermann (LBL) and Bernd Surrow (MIT) August 2, 2004 Abstract The following

More information

Minimum Ignition Energy Test Apparatus for Dust Cloud

Minimum Ignition Energy Test Apparatus for Dust Cloud Minimum Ignition Energy Test Apparatus for Dust Cloud Industrial Explosion Protection Institute Northeastern University, P. R. China Jan. 3, 2010 1 Introduction Minimum ignition energy is the lowest energy

More information

Five Years of Accelerator Operation Experience at HIT Andreas Peters Heidelberg Ion Beam Therapy Centre (HIT), Head Accelerator Operations

Five Years of Accelerator Operation Experience at HIT Andreas Peters Heidelberg Ion Beam Therapy Centre (HIT), Head Accelerator Operations Five Years of Accelerator Operation Experience at HIT Andreas Peters Heidelberg Ion Beam Therapy Centre (HIT), Head Accelerator Operations HIT Betriebs GmbH am Universitätsklinikum Heidelberg http://www.hit-centrum.de

More information

PIPELINE REPAIR OF CORROSION AND DENTS: A COMPARISON OF COMPOSITE REPAIRS AND STEEL SLEEVES

PIPELINE REPAIR OF CORROSION AND DENTS: A COMPARISON OF COMPOSITE REPAIRS AND STEEL SLEEVES Proceedings of the 2014 10th International Pipeline Conference IPC2014 September 29 - October 3, 2014, Calgary, Alberta, Canada IPC2014-33410 PIPELINE REPAIR OF CORROSION AND DENTS: A COMPARISON OF COMPOSITE

More information

COLD PLATE SOFTWARE PROGRAM ANALYZES AIRCRAFT

COLD PLATE SOFTWARE PROGRAM ANALYZES AIRCRAFT COLD PLATE SOFTWARE PROGRAM ANALYZES AIRCRAFT DISPLAY T. Renaud Sanders, a Lockheed Martin Co. Nov, 2000 Introduction Finned heat exchangers, called cold plates, have been used for many years to cool military

More information

TECHNICAL GUIDE FOR PROXIMITY SENSORS DEFINITIONS YAMATAKE PROXIMITY SENSOR CATEGORIES

TECHNICAL GUIDE FOR PROXIMITY SENSORS DEFINITIONS YAMATAKE PROXIMITY SENSOR CATEGORIES TECHNICAL GUIDE FOR PROXIMITY SENSORS DEFINITIONS "" includes all sensors that detect the presence of a metallic object approaching the sensing face or near the sensing face without mechanical contact.

More information

Enhanced Breakdown Voltage for All-SiC Modules

Enhanced Breakdown Voltage for All-SiC Modules Enhanced Breakdown Voltage for All-SiC Modules HINATA, Yuichiro * TANIGUCHI, Katsumi * HORI, Motohito * A B S T R A C T In recent years, SiC devices have been widespread mainly in fields that require a

More information

600 A CURRENT LEADS WITH DRY AND COMPACT WARM TERMINALS

600 A CURRENT LEADS WITH DRY AND COMPACT WARM TERMINALS EUROPEAN ORGANIZATION FOR NUCLEAR RESEARCH European Laboratory for Particle Physics Large Hadron Collider Project LHC Project Report 605 600 A CURRENT LEADS WITH DRY AND COMPACT WARM TERMINALS T.P. Andersen

More information

Journal of Emerging Trends in Computing and Information Sciences

Journal of Emerging Trends in Computing and Information Sciences Pothole Detection Using Android Smartphone with a Video Camera 1 Youngtae Jo *, 2 Seungki Ryu 1 Korea Institute of Civil Engineering and Building Technology, Korea E-mail: 1 ytjoe@kict.re.kr, 2 skryu@kict.re.kr

More information

CHAPTER 6 DESIGN AND DEVELOPMENT OF DOUBLE WINDING INDUCTION GENERATOR

CHAPTER 6 DESIGN AND DEVELOPMENT OF DOUBLE WINDING INDUCTION GENERATOR 100 CHAPTER 6 DESIGN AND DEVELOPMENT OF DOUBLE WINDING INDUCTION GENERATOR 6.1 INTRODUCTION Conventional energy resources are not sufficient to meet the increasing electrical power demand. The usages of

More information

The ITk strips tracker for the phase-ii upgrade of the ATLAS detector of the HL-LHC

The ITk strips tracker for the phase-ii upgrade of the ATLAS detector of the HL-LHC The ITk strips tracker for the phase-ii upgrade of the ATLAS detector of the HL-LHC Afroditi Koutoulaki on behalf of the ATLAS Collaboration 14th Topical Seminar on Innovative Particle and Radiation Detectors

More information

INFN LNF DAΦNE. DAΦNE Storage Ring. Laminated Yoke Quadrupole Low carbon steel Magnetil B-C

INFN LNF DAΦNE. DAΦNE Storage Ring. Laminated Yoke Quadrupole Low carbon steel Magnetil B-C and Storage Ring In 1993 the Company was awarded by INFN-LNF a contract for the turn-key construction of the Transfer Lines for the e+e-φ-factory DAΦNE in Frascati - Rome. The contract included resistive

More information

KINEMATICAL SUSPENSION OPTIMIZATION USING DESIGN OF EXPERIMENT METHOD

KINEMATICAL SUSPENSION OPTIMIZATION USING DESIGN OF EXPERIMENT METHOD Jurnal Mekanikal June 2014, No 37, 16-25 KINEMATICAL SUSPENSION OPTIMIZATION USING DESIGN OF EXPERIMENT METHOD Mohd Awaluddin A Rahman and Afandi Dzakaria Faculty of Mechanical Engineering, Universiti

More information

Power Integrity Guidelines Samtec MPT/MPS Series Connectors Measurement and Simulation Data

Power Integrity Guidelines Samtec MPT/MPS Series Connectors Measurement and Simulation Data Power Integrity Guidelines Samtec MPT/MPS Series Connectors Measurement and Simulation Data Scott McMorrow, Director of Engineering Page 1 Modeled Section MPS Board MPT Board Power Via Power Via Power

More information

SH 249 IN GRIMES COUNTY. Open House April 3, 2014

SH 249 IN GRIMES COUNTY. Open House April 3, 2014 SH 249 IN GRIMES COUNTY Open House April 3, 2014 Meeting Agenda Purpose of Meeting Today: Review the purpose and need for the SH 249 Grimes County project Review the proposed project and alternatives Discuss

More information

Actuator Products Rodless Cylinders. GDL Series. Material specifications. Specifications OSP-P. Series. Series P1X. Series P1Z.

Actuator Products Rodless Cylinders. GDL Series. Material specifications. Specifications OSP-P. Series. Series P1X. Series P1Z. Catalog PDN1-3US High Performance : (s FDC12HP-... thru FDC45HP-...) The High Performance series is the basis for s development, which is used in the majority of applications. High Performance guides consist

More information

Thread Forming Technology for Light Metals

Thread Forming Technology for Light Metals Thread Forming Technology for Light Metals Cost & Design Savings Advantages High joint strength Safety against dynamic loads Consistently high clamp loads Self-locking vibration resistance Easy lead-in,

More information

Optimizing Battery Accuracy for EVs and HEVs

Optimizing Battery Accuracy for EVs and HEVs Optimizing Battery Accuracy for EVs and HEVs Introduction Automotive battery management system (BMS) technology has advanced considerably over the last decade. Today, several multi-cell balancing (MCB)

More information

Special edition paper

Special edition paper Countermeasures of Noise Reduction for Shinkansen Electric-Current Collecting System and Lower Parts of Cars Kaoru Murata*, Toshikazu Sato* and Koichi Sasaki* Shinkansen noise can be broadly classified

More information

Methodology for Distributed Electric Propulsion Aircraft Control Development with Simulation and Flight Demonstration

Methodology for Distributed Electric Propulsion Aircraft Control Development with Simulation and Flight Demonstration 1 Methodology for Distributed Electric Propulsion Aircraft Control Development with Simulation and Flight Demonstration Presented by: Jeff Freeman Empirical Systems Aerospace, Inc. jeff.freeman@esaero.com,

More information

Cross Flow Heat Exchanger H352

Cross Flow Heat Exchanger H352 Cross Flow Heat Exchanger H352 H352 Cross Flow Heat Exchanger Shown With Optional Plain Tube of H352A fitted. Allows Investigation Of Plain And Finned Cross Flow Heat Exchangers. Expandable Free & Forced

More information

Workshop on Accelerator Operations Roger Erickson Accelerator Operations and Safety Division

Workshop on Accelerator Operations Roger Erickson Accelerator Operations and Safety Division Workshop on Accelerator Operations 2012 Roger Erickson Accelerator Operations and Safety Division SLAC SLAC is operated by Stanford University for the U.S. Department of Energy. Approx 420 acres. 1400

More information

Advanced Virgo Beam Geometry

Advanced Virgo Beam Geometry Advanced Virgo Beam Geometry Stefan Hild for OSD OSD internal review, March 2009 Executive summary: Beam Geometry Advanced Virgo needs to have a sensitivity competitive with Advanced LIGO in order to contribute

More information

XFEL Bunch Compressor BC1 and BC2 Vacuum Issues

XFEL Bunch Compressor BC1 and BC2 Vacuum Issues Bunch Compressor BC1 and BC2 Vacuum Issues Nils Mildner, Torsten Wohlenberg, Kirsten Zapfe Beam Dynamic Meeting 1 Bunch compressor section BC1 and BC2 General remarks Lengths of the vacuum system BC1 and

More information

Development of low-mass, high-density, hybrid circuit for the silicon microstrip sensors in high track density environment

Development of low-mass, high-density, hybrid circuit for the silicon microstrip sensors in high track density environment Development of low-mass, high-density, hybrid circuit for the silicon microstrip sensors in high track density environment 1 T. Kohriki, S. Terada, Y. Unno INPS, High Energy Accelerator Organization (KEK),

More information

Inspection Testing Repair

Inspection Testing Repair Inspection Testing Repair Generator Technical Services 1810 Blackwell Lane Penascola, FL 32514 Phone (850) 471-1101 Fax (850) 471-1104 Email: info@gentechservices.com Power Generation Generator Technical

More information

Reduction of Self Induced Vibration in Rotary Stirling Cycle Coolers

Reduction of Self Induced Vibration in Rotary Stirling Cycle Coolers Reduction of Self Induced Vibration in Rotary Stirling Cycle Coolers U. Bin-Nun FLIR Systems Inc. Boston, MA 01862 ABSTRACT Cryocooler self induced vibration is a major consideration in the design of IR

More information

This chapter gives details of the design, development, and characterization of the

This chapter gives details of the design, development, and characterization of the CHAPTER 5 Electromagnet and its Power Supply This chapter gives details of the design, development, and characterization of the electromagnets used to produce desired magnetic field to confine the plasma,

More information

TSC INSPECTION SYSTEMS

TSC INSPECTION SYSTEMS TSC INSPECTION SYSTEMS APPLICATIONS OF ACFM IN THE RAIL INDUSTRY ACFM was originally developed for use in the oil and gas industry as a technique for detecting and sizing surface-breaking defects with

More information

Size 1206, 1210, 0805, 0603, 0402 (Anti-Sulfuration )

Size 1206, 1210, 0805, 0603, 0402 (Anti-Sulfuration ) SR12, SR10, SR08, SR06, SR04, General purpose chip resistors Size 1206, 1210, 0805, 0603, 0402 (Anti-Sulfuration ) *Contents in this sheet are subject to change without prior notice. Page 1 of 9 ASC_SR_V03

More information

Comparing FEM Transfer Matrix Simulated Compressor Plenum Pressure Pulsations to Measured Pressure Pulsations and to CFD Results

Comparing FEM Transfer Matrix Simulated Compressor Plenum Pressure Pulsations to Measured Pressure Pulsations and to CFD Results Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2012 Comparing FEM Transfer Matrix Simulated Compressor Plenum Pressure Pulsations to Measured

More information

Project Summary Fuzzy Logic Control of Electric Motors and Motor Drives: Feasibility Study

Project Summary Fuzzy Logic Control of Electric Motors and Motor Drives: Feasibility Study EPA United States Air and Energy Engineering Environmental Protection Research Laboratory Agency Research Triangle Park, NC 277 Research and Development EPA/600/SR-95/75 April 996 Project Summary Fuzzy

More information

Pre-normative research on resistance to mechanical impact of composite overwrapped pressure vessels. Dr. Fabien Nony CEA

Pre-normative research on resistance to mechanical impact of composite overwrapped pressure vessels. Dr. Fabien Nony CEA Pre-normative research on resistance to mechanical impact of composite overwrapped pressure vessels Dr. Fabien Nony CEA http://hypactor.eu/ Email Coordinator: fabien.nony@cea.fr Programme Review Days 2017

More information

Development of a Finite Element Model of a Motorcycle

Development of a Finite Element Model of a Motorcycle Development of a Finite Element Model of a Motorcycle N. Schulz, C. Silvestri Dobrovolny and S. Hurlebaus Texas A&M Transportation Institute Abstract Over the past years, extensive research efforts have

More information