Installation, Operation and Maintenance Manual. EVC Controller (from February 2007)

Size: px
Start display at page:

Download "Installation, Operation and Maintenance Manual. EVC Controller (from February 2007)"

Transcription

1 Installation, Operation and Maintenance Manual (from February 2007) Publication 2698C (GB) A B Donaldson reserve the right to alter design without notice. Freedom from patent restrictions must not be assumed.

2 IMPORTANT PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLATION THIS MANUAL SHOULD BE READ IN CONJUNCTION WITH THE RESPECTIVE PRODUCT MANUAL SUPPLIED WITH THE DUST COLLECTOR EXPLANATION OF SYMBOLS USED Indicates information on the efficient operation of the collector. Indicates important information directed towards preventing damage. Indicates an important warning, designed to prevent injury or extensive damage. 2

3 CONTENTS Installation Dalamatic Insertable... 5 Downflo Oval... 5 Siloair... 5 Spotair... 5 Unicell Unit... 5 Overload protection... 6 Connections and set-up... 6 Interrupt option... 6 Off-line cleaning facility... 6 Operation Description... 8 Interrupt option... 8 Off-line cleaning facility... 8 Maintenance Overload protection... 9 Replacement PCBs... 9 Fault location... 9 Specification Description Voltage inputs Voltage outputs Power requirements Spare Parts Declaration of Conformity Table 1 Controller installation settings... 7 Table 2 Fault location Table 3 Terminal connections Figure 1 PCB layout for... 4 Figure 2 Typical diagram for remote control connection

4 INSTALLATION V incoming supply fuse (F2) 500 ma (T) 2 230V incoming supply fuse (F3) 315 ma (T) 3 Transformer connectors 4 Solenoid output fuse (F1) 630 ma (F) 5 Pulse duration and interval setting switch 6 Number of solenoid outputs ('ways') selector 7 Off-line cleaning LED (Yellow) 8 Earth stud 9 Incoming supply terminal block 10 Incoming supply voltage selector 11 Pulse indication LEDs (Red) 12 Output to solenoids terminal block 13 Power-on LED (Green) 14 Pause LED (Green) 15 Interrupt and off-line cleaning terminal block Figure 1 PCB layout for (AC version) 4

5 INSTALLATION It is a requirement of the Supply of Machinery (Safety) Regulations 1992 to provide adequate isolation and emergency stop facilities. Due to the varied nature of site installations this cannot be provided by Donaldson but instead is the responsibility of the customer. All electrical work should be carried out by competent personnel. Always isolate power before opening the controller. For installation in hazardous areas, all work must be carried out with the electrical supply isolated or only when the potentially explosive atmosphere is not present. Checks should be made to ensure the category of equipment is suitable for the zone in which the installation is made. The following dust collectors are supplied with an, which is used to operate the reverse jet cleaning. Dalamatic Insertable (DLM V3/7 to V20/10): The controller is supplied loose. Attach the controller to the filter body in accordance with the installation instructions in the dust collector product manual, publication Downflo Oval (DFO 1-1, 2-2 and 3-3): The controller is supplied fully fitted to the collector, mounted on the control equipment access panel. Siloair: The controller is supplied fully fitted to the filter body, below the compressed air manifold. Spotair: The controller is supplied fully fitted to the top of the filter body, adjacent to the compressed air manifold. Unicell Unit: On C10-30 hopper type collectors, C10-30 venting type collectors and C10-30 venting type collectors with dust container, the controller is supplied fully fitted to the base section. On C40-90 collectors the controller is supplied fully fitted to the controls section. On C10-30 standard collectors with dust container or rotary valve and C10-30 venting type collectors with rotary valve, the controller is supplied fitted to the base section. Connect the tubing in accordance with the installation instructions in the dust collector product manual, publication

6 INSTALLATION All terminal blocks are removable for ease of connection. Overload protection A fused isolator, fitted with either a 4A fuse for 24V supply or a 1A fuse for 110/ 240V supply, should be fitted between the controller and incoming supply. A high rupturing capacity (HRC) cartridge-type fuse must be used. Connections and set-up Open the enclosure. Connect the incoming supply to the terminal block (see Fig. 1). On the AC version ensure that the voltage setting link is set for the incoming supply voltage. Connect the protective earth conductor to the earth stud on the enclosure base (see Fig. 1) using the ring terminal supplied. The mains cables should not exert any undue stress on the terminal block. The use of multistrand conductors is advised. Ensure that socket is fully engaged into the plug on the PCB. Ensure that the switch for the pulse duration and the interval between pulses (see Fig. 1) is set in accordance with Table 1. Also ensure that the setting link for the number of 'ways' is configured to the corresponding number of solenoid valves (see Fig. 1 and Table 1). Close the lid and switch on the mains supply. The cleaning sequence will commence. Refer to dust collector product manual for start-up procedure of equipment. Interrupt option For a description of this option, refer to 'Operation' section. In order to utilise this function, a volt free contact should be connected across terminals 7 and 8 on the PCB (see Fig. 1). Closing the contact stops the cleaning cycle, opening the contact restarts the cycle. When the interrupt signal is received, the green pause LED will illuminate continuously and the yellow LED will flash rapidly. Off-line cleaning facility For a description of this facility, refer to 'Operation' section. In order for this function to operate, remove the bridging link between terminals 9 and 10 on the PCB (see Fig. 1) and connect a normally open contact on the fan starter across terminals 9 and 10. The power to the controller must be permanently connected. When the fan starts and contacts 9 and 10 are closed, the controller will operate normally. When the fan stops and the contacts are opened, the controller will continue to pulse for a fixed number of cycles and then stop. The interrupt function will override the off-line cleaning function. 6

7 INSTALLATION TABLE 1 CONTROLLER INSTALLATION SETTINGS Dust collector type Pulse duration and interval switch setting No. of 'ways' Dalamatic Insertable Models: V3/7 and V5/ way Models: V4/7, V6/10, V7.5/12, V8/7, V9/15, V12/10, V15/12 and V18/ way Models: V7/7, V10/10, V13/12, V14/7, V15/15 and V20/10 (5-valve version) 8 5-way Downflo Oval Model: DFO way Model: DFO way Model: DFO way Spotair All models 8 2-way Siloair Models: VS10, VS14, VS15 and VS way Models: VS20 and VS way Unicell Model: C way Models: C20 and C way Models: C50 and C way Models: C30, C60 and C way These figures apply to collectors built from February For collectors built prior to this date refer to product manual. 7

8 OPERATION The controller is fully automatic and ensures that the diaphragm valves of the dust collector it serves are operated in sequence, at regular intervals, to facilitate the efficient cleaning of the filter elements. The pulse duration and the interval between pulses must be set according to the specific dust collector model (see Table 1). These figures should not be altered without prior consultation with Donaldson. Interrupt option The controller offers the facility to interrupt and restart the cleaning cycle at any point. This is particularly useful on venting applications where the actual filter operates over a short period of time (e.g. pneumatic conveying of small quantities of product) where a complete cleaning cycle may not take place. Under normal circumstances if the power to the controller is switched off the cleaning cycle is reset to the first element position when the power is reapplied. The interrupt option can be used to start and stop the cleaning without the controller resetting, provided that the power is left on, ensuring that all filter elements are cleaned. When the interrupt signal has stopped the cleaning cycle, the green pause LED will illuminate continuously and the yellow LED will flash rapidly. Off-line cleaning facility This function (when enabled) allows the cleaning cycle to continue for a fixed number of cycles after the fan has been switched off, provided that the power to the controller is left on. The yellow off-line cleaning LED will flash during off-line cleaning and then flash slowly when off-line cleaning is complete and the controller is in 'stand-by'. 8

9 MAINTENANCE On outside installations, always isolate power before opening the controller in wet weather conditions. For controllers installed in potentially hazardous areas, suitable precautions should be taken to ensure no ignition sources are introduced or that the atmosphere is not hazardous during any maintenance operations or when making adjustments to operating parameters when the controller is energised. Overload protection A fused isolator, fitted with either a 4A fuse for 24V supply or a 1A fuse for 110/ 240V supply, should be fitted between the controller and incoming supply. A high rupturing capacity (HRC) cartridge-type fuse must be used. Protection of the controller against an output current overload is achieved by a small HRC cartridge fuse mounted on the PCB (see Fig. 1). In an emergency a quick-acting fuse could be used as a temporary alternative but a time delay fuse must not be used under any circumstances. Replacement PCBs Isolate supply to controller. The fitment of replacement PCBs is relatively simple. However, it must be noted that the PCB assembly is a universal spare and must be configured to the number of solenoid valves fitted. In order to do this the jumper links, denoted by the symbol (see Fig. 1), must be in the correct position (see Table 1). Failure to carry out this procedure will result in poor filter performance. Fault location In the event of a controller failure, refer to Table 2 to identify the fault. 9

10 MAINTENANCE TABLE 2 FAULT LOCATION Symptom Possible cause Action A Green power-on LED not illuminated. Electrical supply fault. Check supply circuit for proper voltage. Check fuses, circuit breakers etc. Replace as required. Incorrect wiring. Check correct wiring connections to PCB (refer to 'Installation' section). Fuses have blown. Check fuses. If fuses are blown check wiring connections. Replace fuses with correct type (refer to 'Maintenance' section). (On DC version, incorrect polarity will cause fuse to blow). Internal controller failure. Replace PCB. B No cleaning pulses. Supply problem (green LED not illuminated). Refer to section A of Fault Location Table. Yellow LED flashing rapidly. Interrupt function is activated. Cleaning cycle will stop if terminals 7 and 8 are connected. Off-line cleaning connection is not closed (yellow LED flashing slowly). For normal cleaning operation, terminals 9 and 10 should be connected. If off-line cleaning is not being activated from external contact, these should be linked. Low supply voltage. Check supply voltage (a low voltage will not open valves but may operate LEDs normally). Solenoid valves not connected correctly. Check connections to solenoid valves in enclosure. Ensure connection plug is correctly engaged in PCB socket. C No off-line cleaning. Supply problem (green LED not illuminated). Refer to section A of Fault Location Table. Yellow LED flashing rapidly. Interrupt function is activated. Cleaning cycle will stop if terminals 7 and 8 are connected. Terminals 9 and 10 connected. Off-line cleaning activated by opening connection between terminals 9 and 10. D Incorrect/gaps in valve firing sequence. Solenoid valves not connected correctly. Check connections to solenoid valves in enclosure. Ensure connection plug is correctly engaged in PCB socket. Setting link fitted incorrectly. Check setting link position. E Weak pulses. Air supply inadequate. Check compressor capacity. Check pulse interval (air pressure in manifold should return to required value before next pulse). Supply voltage too low. Check supply voltage and connections to PCB. Restriction in tubing / tubing too long. Check tubing between solenoids and diaphragm valves. 10

11 SPECIFICATION The EVC controller complies with the electromagnetic emissions/immunity requirements of the European Directive 89/336/EEC, together with all current world standards (e.g. BS standard for Electrical/Electronic equipment EN ). The controller consists of an IP65 weatherproof steel enclosure, with either AC or DC input voltage options. Mounted within the box is a printed circuit board, together with the appropriate number of solenoid valves; a transformer is also fitted to the AC version. The operating temperature range for the controller is 10 C to +60 C at 25% RH, or 10 C to +45 C at 81% RH. (For temperatures outside these limits refer to Donaldson). The controller is suitable for working within a Potentially Explosive Atmosphere (as defined by Directive 94/9/EC) according to the categories and conditions marked on the serial nameplate. When installing the controller in these circumstances, reference should also be made to the Supplementary Information, Publication 2875, supplied with the dust collector. Voltage inputs AC version: V or V, 1 phase, 50/60 Hz DC version: 24V ±10% Voltage outputs Solenoid valve pulses: 24V DC (20W max.) Power requirements AC version: 15VA (incoming supply fuse 1A) DC version: 15W (incoming supply fuse 4A) AC and DC versions of the controller are not interchangeable. K1 Interrupt terminals, e.g. PLC system K2 Off-line cleaning terminals, use auxiliary contactor on fan starter K1 K } } Interrupt terminals Off-line cleaning terminals Figure 2 Typical diagram for remote control connection 11

12 SPECIFICATION TABLE 3 TERMINAL CONNECTIONS Terminal Item Description Remarks L N Power supply connections (AC version) 240V AC / 110V AC 0V AC (Neutral) Protective Earth (Stud on enclosure) Ensure the voltage setting link is set for the incoming supply voltage + Power supply connections (DC version) 24V DC + (Positive) 24V DC (Negative) Protective Earth (Stud on enclosure) Incorrect polarity will cause fuse to blow 7 8 Interrupt terminals Inputs to connect remote switch to stop cleaning operation. Closing switch halts pulsing sequence Use volt-free contact 9 10 Off-line cleaning terminals Inputs to connect remote switch to activate off-line cleaning sequence. Closing switch starts controller operation, opening switch stops controller normal operation and initiates off-line cleaning sequence Use volt-free contact. Power supply must remain connected throughout. Terminals supplied bridged + V1 to V6 Solenoid valve outputs + common connection Valve outputs 1 to 6 24V DC SPARE PARTS Description Part Number PCB PCB 110/220V AC 24V DC 1A A Solenoid valve Transformer 1A A

13 DECLARATION OF CONFORMITY 13

14 Humberstone Lane Thurmaston Leicester LE4 8HP England Tel +44 (0) Fax +44 (0) Research Park Zone 1 Interleuvenlaan 1 B-3001 Leuven (Heverlee) Belgium Tel +32 (0) Fax +32 (0) IFS-europe@emea.donaldson.com

DCE 100 Series Dust Filter

DCE 100 Series Dust Filter Installation, Operation and Maintenance Manual DCE 100 Series Dust Filter Publication 2638B (GB) 0702 1419-8000A Donaldson Torit DCE reserve the right to alter design without notice. Freedom from patent

More information

Unicell Dust Collectors Series C10-90

Unicell Dust Collectors Series C10-90 Unicell Dust Collectors Series C10-90 500 required for maintenance A 0 minimum clearance B h 1150 required for maintenance d Refer to page 7 Lifting bracket (removable) Refer to page 7 Cleaned air outlet

More information

Dalamatic Cased Dust Filters Series DLM 15

Dalamatic Cased Dust Filters Series DLM 15 Dalamatic Cased Dust Filters Series DLM 8 1 bank 1100 2 bank 2105 3 bank 3110 1005 1005 5 5 290 700 2285 10 1360 (17 required for maintenance) 600 required for maintenance 465 (4- to 8-tier) 235 (2- &

More information

DCE 2000 Series Dust Collectors

DCE 2000 Series Dust Collectors f required for maintenance Refer to page 23 A 50 500* B 500* required for minimum maintenance clearance 38 120* Lifting bracket (removable) Contaminated Refer to page 23 Cleaned air outlet Fan terminal

More information

PowerCore Dust Collectors Series CPC

PowerCore Dust Collectors Series CPC PowerCore Dust Collectors Series CPC PowerCore dust collector with dust container (without fan). (CPC-6 illustrated). Suitable for inside locations and outside when fitted with optional weather cowl. 600

More information

DCE 100 Series Dust Filters

DCE 100 Series Dust Filters Installation, Operation and Maintenance Manual s Publication 2638D (GB) 1208 1A 1419 8000D Donaldson reserve the right to alter design without notice. Freedom from patent restrictions must not be assumed.

More information

Unimaster Dust Collectors Series UMA

Unimaster Dust Collectors Series UMA Unimaster Dust Collectors Series UM 70-2 d required for maintenance Lifting bracket (removable) 230 minimum clearance 102 Cleaned air outlet 380 required for cleaner motor cover removal coustic diffuser

More information

HILLSTONE DC LOAD BANK

HILLSTONE DC LOAD BANK OPERATING MANUAL for HILLSTONE DC LOAD BANK Type ref. HLD 240 480 100 Serial No. M36771 ISSUE 1 1 CONTENTS Introduction page 3 Safety Considerations page 3 Connecting procedure page 4 Operating instructions

More information

Unimaster Dust Collectors Series UMA

Unimaster Dust Collectors Series UMA Unimaster Dust Collectors Series UM 70-2 d required for maintenance Lifting bracket (removable) 230 minimum clearance 102 Cleaned air outlet 380 required for cleaner motor cover removal coustic diffuser

More information

DEEP SEA ELECTRONICS PLC

DEEP SEA ELECTRONICS PLC COMPLEX SOLUTIONS MADE SIMPLE DEEP SEA ELECTRONICS PLC DSE704 AUTOSTART CONTROL MODULE OPERATING MANUAL 057-042 704 Operating Instructions Issue 2.1 18/06/2007 11:27:00 JR - 1 - Deep Sea Electronics Plc

More information

Reviewed: DD Month University Code of Practice for Electrical Safety. PART B - Design and Construction of Electrical Equipment within the University

Reviewed: DD Month University Code of Practice for Electrical Safety. PART B - Design and Construction of Electrical Equipment within the University Safety Office Reviewed: 17 July 2012 Reviewed: DD Month University Code of Practice for Electrical Safety PART B - Design and Construction of Electrical Equipment within the University The purpose of this

More information

MPS AND MPS PR¼ 16 OUTPUT DEMAND CONTROLLER PENTAIR CLEAN AIR SYSTEMS. AVS Danmark ApS Skelvej Hedehusene

MPS AND MPS PR¼ 16 OUTPUT DEMAND CONTROLLER PENTAIR CLEAN AIR SYSTEMS. AVS Danmark ApS Skelvej Hedehusene MPS AND MPS PR¼ 16 OUTPUT DEMAND PENTAIR CLEAN AIR SYSTEMS MPS DESCRIPTION The Model MPS has been designed to guarantee the control of diaphragm valves mounted on pulse-jet dust collector filters containing

More information

RE-PR3-E-86&105 3-Phase Panel Mount 86 and 105kW

RE-PR3-E-86&105 3-Phase Panel Mount 86 and 105kW Page 1 of 6 3-Phase Panel Mount 86 and 105kW Features: Benefits: 0-10Vdc, 0-5Vdc, 4-20mA or manual via potentiometer control input Over temperature protection with auto reset Enclosed panel mounting Efficient

More information

Dalamatic Concept Dust Collectors Series D60-225

Dalamatic Concept Dust Collectors Series D60-225 Installation, Operation and Maintenance Manual Dalamatic Concept Dust Collectors Series D60-225 Publication 1728F (GB) 1006 3219-8009C Donaldson reserve the right to alter design without notice. Freedom

More information

Phoenix Inverter

Phoenix Inverter Manual EN Handleiding NL Manuel FR Anleitung DE Manual ES Appendix Phoenix Inverter 12 250 12 375 12 500 12 800 24 250 24 375 24 500 24 800 48 250 48 375 48 500 48 800 1. Safety instructions WARNING: ELECTRIC

More information

M Series Condensate Recovery Unit

M Series Condensate Recovery Unit 0898050/3 IM-P089-29 ST Issue 3 M Series Condensate Recovery Unit Installation and Maintenance Instructions 1. General safety information 2. General product information 3. Installation 4. Wiring diagram

More information

Dalamatic Cased Dust Collectors Series DLM 15

Dalamatic Cased Dust Collectors Series DLM 15 Dalamatic Cased Dust Collectors Series DLM 8 1-bank 1100 2-bank 2105 3-bank 3110 1005 1005 5 5 2285 10 (17 required for maintenance) 290 700 1360 600 required for maintenance 4- to 8-tier 465 2- and 3-tier

More information

KV4-300 mk2. KV5-200 mk2. KV5-100T mk2. KV3-250 mk2

KV4-300 mk2. KV5-200 mk2. KV5-100T mk2. KV3-250 mk2 OPERATING AND MAINTENANCE MANUAL Product: Type: High Voltage AC Test Set KV3-250 mk2 KV4-300 mk2 KV5-100 mk2 KV5-100T mk2 KV5-200 mk2 DESIGNED AND MANUFACTURED BY: T & R Test Equipment Limited 15-16 Woodbridge

More information

MODEL 520 REMOTE START ENGINE MANAGEMENT SYSTEM

MODEL 520 REMOTE START ENGINE MANAGEMENT SYSTEM MODEL 520 REMOTE START ENGINE MANAGEMENT SYSTEM DSE 520 ISSUE 4 4/4/02 MR 1 TABLE OF CONTENTS Section Page INTRODUCTION... 4 CLARIFICATION OF NOTATION USED WITHIN THIS PUBLICATION.... 4 1. OPERATION...

More information

Total Control Board. Installation, Operation and Maintenance Manual. Publication 2949A (GB) (From October 2007)

Total Control Board. Installation, Operation and Maintenance Manual. Publication 2949A (GB) (From October 2007) Total Control Board (From October 2007) Publication 2949A (GB) 1108 Freedom from patent restrictions must not be assumed. IMPORTANT PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLATION THIS MANUAL SHOULD

More information

702 AUTOMATIC START MODULE OPERATING INSTRUCTIONS

702 AUTOMATIC START MODULE OPERATING INSTRUCTIONS 702 AUTOMATIC START MODULE OPERATING INSTRUCTIONS > TABLE OF CONTENTS 1 DESCRIPTION OF OPERATION... 4 1.1 MANUAL MODE OPERATION... 4 1.2 AUTOMATIC MODE OF OPERATION...

More information

DEEP SEA ELECTRONICS PLC

DEEP SEA ELECTRONICS PLC COMPLEX SOLUTIONS MADE SIMPLE. DEEP SEA ELECTRONICS PLC DSE4120 AUTO MAINS FAILURE MODULE OPERATING MANUAL Deep Sea Electronics Plc Highfield House Hunmanby North Yorkshire YO14 0PH ENGLAND Sales Tel:

More information

MAKING MODERN LIVING POSSIBLE. Quick Setup VLT FCM 300 Series. Phone: Fax: Web: -

MAKING MODERN LIVING POSSIBLE. Quick Setup VLT FCM 300 Series. Phone: Fax: Web:  - MAKING MODERN LIVING POSSIBLE Quick Setup VLT FCM 300 Series Factory setting Motors type B14 & B34 mounting Reset (pushbutton) Start Jog Speed reference Fig. 1 - Reset to be closed short time for resetting

More information

DEEP SEA ELECTRONICS PLC

DEEP SEA ELECTRONICS PLC COMPLEX SOLUTIONS MADE SIMPLE. DEEP SEA ELECTRONICS PLC DSE710 AUTOSTART CONTROL MODULE OPERATING MANUAL Deep Sea Electronics Plc Highfield House Hunmanby North Yorkshire YO14 0PH ENGLAND Sales Tel: +44

More information

ECONOMISER SERIES E2T USER MANUAL

ECONOMISER SERIES E2T USER MANUAL TURBO S.R.L. Electronic Control Systems for Dust Collectors e-mail: info@turbocontrols.it web: www.turbocontrols.it TEL. ++39 (0)362 574024 FAX ++39 (0)362 574092 ECONOMISER SERIES E2T USER MANUAL 24/06/2014

More information

Pro Booster 802Li. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference.

Pro Booster 802Li. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate

More information

DEEP SEA ELECTRONICS PLC

DEEP SEA ELECTRONICS PLC COMPLEX SOLUTIONS MADE SIMPLE DEEP SEA ELECTRONICS PLC DSE720 AUTOSTART CONTROL MODULE OPERATING MANUAL http://bestgenerator.spb.ru/?page_id=6765 Deep Sea Electronics Plc Highfield House Hunmanby North

More information

INSTRUCTION MANUAL (ATEX / IECEx)

INSTRUCTION MANUAL (ATEX / IECEx) INSTRUCTION MANUAL (ATEX / IECEx) BExBGL2D LED BEACON For use in Flammable Gas and Dust Atmospheres BExBGL2D 1) Warnings DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT DO NOT OPEN WHEN ENERGIZED POTENTIAL

More information

KD LV Motor Protection Relay

KD LV Motor Protection Relay 1. Protection Features KD LV Motor Protection Relay Overload (for both cyclic and sustained overload conditions) Locked rotor by vectorial stall Running stall / jam Single phasing / Unbalance Earth leakage

More information

PULSE-8: MASTER PULSATION CONTROL

PULSE-8: MASTER PULSATION CONTROL PULSE-8: CONTROL Version - February 2006 For Software Version V1.02 Part Number - 39-0020 CONTROL: INDEX GOOD PRACTICE: Mains Supply. A separate mains supply and earth running directly from the consumer

More information

DEEP SEA ELECTRONICS PLC

DEEP SEA ELECTRONICS PLC DEEP SEA ELECTRONICS PLC 703 AUTOMATIC START MODULE OPERATING INSTRUCTIONS Author:- John Ruddock 703 Operating Instructions Issue Beta1 25/08/2003 2:45 PM JR - 1 - >

More information

Dalamatic Insertable Dust Collectors Series DLM V

Dalamatic Insertable Dust Collectors Series DLM V Dalamatic Insertable Dust ollectors Series DLM V 0* B 0* j g 0* A 0* 167 220 S e a t i n g l e v e l f* ompressed air inlet ½" BSP Parallel Manometer connection (optional) entre-line of aperture 12 10

More information

OPERATING AND MAINTENANCE MANUAL. Primary Current Injection Test Set. 750ADM-H mk2

OPERATING AND MAINTENANCE MANUAL. Primary Current Injection Test Set. 750ADM-H mk2 OPERATING AND MAINTENANCE MANUAL Product: Type: Primary Current Injection Test Set 750ADM mk2 750ADM-H mk2 DESIGNED AND MANUFACTURED BY: T & R Test Equipment Limited 15-16 Woodbridge Meadows, Guildford,

More information

Instruction Manual. Q Series 2 Motor Control Modules - OEM

Instruction Manual. Q Series 2 Motor Control Modules - OEM A382-21-880 Issue B Instruction Manual Q Series 2 Motor Control Modules - OEM Pump/ Q Motor Control Module Item Number pumping system Electrical supply 24 V d.c. control 24 V a.c. control QDP40 200-230

More information

EC225 Power Control System

EC225 Power Control System 1 Key Features 200W (~16A) combined Power Converter / Battery Charger - Converts the 230V mains supply into 12v DC power to run the leisure equipment and charge the battery using an intelligent two-stage

More information

Operating and Installation Instructions Diaphragm Vacuum Pumps and Compressors

Operating and Installation Instructions Diaphragm Vacuum Pumps and Compressors Operating and Installation Instructions Diaphragm Vacuum Pumps and Compressors Type range: UN813.3ANI UN813.4ANI UN813.3ANDCB UN813.4ANDCB UN813.5ANI Fig. 1: UN813.3ANI Fig. 2: UN813.4ANI You have selected

More information

ECU-02 Ver2.1 Automatic Engine Control Unit Operators Manual

ECU-02 Ver2.1 Automatic Engine Control Unit Operators Manual ECU-02 Ver2.1 Automatic Engine Control Unit Operators Manual Headquarters : No.3, Lane 201, Chien Fu St., Chyan Jenn Dist., Kaohsiung, TAIWAN Tel : + 886-7-8121771 Fax : + 886-7-8121775 URL : http://www.kutai.com.tw

More information

Switching DC Power Supply

Switching DC Power Supply 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Model 1693, 1694 Switching DC Power Supply INSTRUCTION MANUAL 1 Safety Summary

More information

CAUTION CM-SE CM-S21 CM-S41

CAUTION CM-SE CM-S21 CM-S41 CAUTION Safety, Technology & Innovation CM Series Operating Instructions for, CM-S21,, CM-S11, CMS31 CM Series Safety System This information is designed to help suitably qualified personnel install and

More information

Dycon D2430 EN54-4 Fire Alarm Power Supply Series

Dycon D2430 EN54-4 Fire Alarm Power Supply Series Dycon D2430 EN54-4 Fire Alarm Power Supply Series Technical Description Installation and Operating Manual Construction Product Regulation 0359-CPR-00434 Page 1 of 14 Contents 1. General... 3 1.1 Product

More information

Technical Documentation

Technical Documentation Technical Documentation Product manual Holding brake controller Document: 0198441113316 Edition: V1.00, 03.2006 Important information The drive systems described here are products for general use that

More information

RELAY BOX PRODUCT MANUAL IMPORTANT

RELAY BOX PRODUCT MANUAL IMPORTANT RELAY BOX PRODUCT MANUAL IMPORTANT Installer: This manual is the property of the customer and must be retained with the product for maintenance and operational purposes. 1 TABLE OF CONTENTS Page INTRODUCTION

More information

POWER SUPPLY aps-412_en 06/16

POWER SUPPLY aps-412_en 06/16 APS-412 POWER SUPPLY aps-412_en 06/16 The APS-412 switching power supply has been designed for use with 12 V DC electrical devices. It comes with a dedicated connector allowing for integration with Satel's

More information

Floodlight Range Installation Guide

Floodlight Range Installation Guide SPARTAN Floodlight Range Installation Guide CML13ATEX3007 IEC Ex CML14.0001 This installation guide provides instructions for installing the Infra-Red and White-Light SPARTAN SPX series of explosion protected

More information

TPAK Series COOLANT PUMP

TPAK Series COOLANT PUMP TPAK Series COOLANT PUMP Instruction Manual ISO 9001 Certified WALRUS PUMP CO., LTD. EC Declaration of Conformity Manufacturer: Walrus Pump Co., Ltd. Address: No.83-14, Dapiantou, Sanzhi Dist., New Taipei

More information

Valcom Failsafe Unit. 1620ESv2 SERIES. Operation and Maintenance Manual

Valcom Failsafe Unit. 1620ESv2 SERIES. Operation and Maintenance Manual Valcom Failsafe Unit 1620ESv2 SERIES Operation and Maintenance Manual Table of Contents Section Title Page 1. - Introduction.. 2. - Unpacking the Failsafe unit. 3. - Installation 3.1 - Auto / Timed UPS

More information

Unicell Dust Collectors Series C required for. required for maintenance. Controller j

Unicell Dust Collectors Series C required for. required for maintenance. Controller j DATA SHEET Unicell Dust Collectors Series C10-90 500 A 0 B 1150 required for minimum required for maintenance clearance h maintenance d refer to page 7 Lifting bracket (removable) Joint line (C, C50, C60,

More information

Operating Instructions

Operating Instructions Important Information: These instructions contain safety information, read and follow them carefully. Dialight will not accept any responsibility for injury, damage or loss which may occur due to incorrect

More information

Burden Fuse Rating Resistor SAF / SAK6 1NM 10mm M8 12NM SAF / SAK10 2NM 16mm M8 12NM

Burden Fuse Rating Resistor SAF / SAK6 1NM 10mm M8 12NM SAF / SAK10 2NM 16mm M8 12NM Contents Section Page 1.0 Introduction 1 2.0 Specification 1-4 3.0 Installation 5-8 4.0 Programming 9-10 5.0 Menus 10-12 6.0 Fault Finding/Diagnostics 12-13 7.0 Communication 13 8.0 Setting Up 13-16 1.0

More information

Chargestar P24 / P32 Battery Charger Startmaster P300 Starter / Charger

Chargestar P24 / P32 Battery Charger Startmaster P300 Starter / Charger Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate

More information

EC200 ELECTRONIC CONTROL SYSTEM

EC200 ELECTRONIC CONTROL SYSTEM 1 INTRODUCING THE EC200 ELECTRONIC CONTROL SYSTEM With the use of new technology and an innovative approach to user interfacing, the EC200 Power Control System provides a complete control solution for

More information

Dycon D1532SM. EN50131/PD6662 Grade 3, 12V 2A Power Supply. Technical Description Installation and Operating Manual DYCON POWER SOLUTIONS LTD

Dycon D1532SM. EN50131/PD6662 Grade 3, 12V 2A Power Supply. Technical Description Installation and Operating Manual DYCON POWER SOLUTIONS LTD Dycon D1532SM EN50131/PD6662 Grade 3, 12V 2A Power Supply Technical Description Installation and Operating Manual DYCON POWER SOLUTIONS LTD Tel: +44 (0)1443 471 900 Unit A Cwm Cynon Business Park Mountain

More information

DKG-114 MANUAL AND REMOTE START UNIT

DKG-114 MANUAL AND REMOTE START UNIT DKG-114 MANUAL AND REMOTE START UNIT FEATURES Both manual and remote controlled engine starting and stopping, Automatic shutdown on fault condition, Optional cooldown cycle on remote start operation, Optional

More information

RE-PR1-F 1-Phase Din-Rail Mount 1.5, 3 & 6kW

RE-PR1-F 1-Phase Din-Rail Mount 1.5, 3 & 6kW Page 1 of 5 RE-PR1-F 1-Phase Din-Rail Mount 1.5, 3 & Features: Benefits: 0-10Vdc or 0-5Vdc control input Over temperature protection with auto reset Din-rail mounting Efficient electronic switching No

More information

TRI-SERVICE ELECTRICAL WORKING GROUP (TSEWG) 03/05/09 TSEWG TP-11: UFC N BEST PRACTICES

TRI-SERVICE ELECTRICAL WORKING GROUP (TSEWG) 03/05/09 TSEWG TP-11: UFC N BEST PRACTICES TSEWG TP-11: UFC 3-500-10N BEST PRACTICES UFC 3-500-10N was developed by NAVFAC and was used as the starting point for the tri-services development of UFC 3-500-10, Design: Electrical Engineering. UFC

More information

Type Operating Instructions. Bedienungsanleitung Manuel d utilisation. 2/2-Way Solenoid Valve 2/2-Wege-Magnetventil Électrovanne à 2/2 voies

Type Operating Instructions. Bedienungsanleitung Manuel d utilisation. 2/2-Way Solenoid Valve 2/2-Wege-Magnetventil Électrovanne à 2/2 voies Type 5282 2/2-Way Solenoid Valve 2/2-Wege-Magnetventil Électrovanne à 2/2 voies Operating Instructions Bedienungsanleitung Manuel d utilisation 1 OPERATING INSTRUCTIONS The operating instructions contain

More information

INSTRUCTION MANUAL (ATEX / IECEx)

INSTRUCTION MANUAL (ATEX / IECEx) INSTRUCTION MANUAL (ATEX / IECEx) BExBG10D-P and BExBG15D-P Flameproof Xenon Beacons For use in Flammable Gas and Dust Atmospheres BExBG10D-P / BExBG15D-P 1) Warnings DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE

More information

CBC-300 Series & CBC-300C Series Dual Channel Adjust Clutch/Brake Controls

CBC-300 Series & CBC-300C Series Dual Channel Adjust Clutch/Brake Controls CBC-300 Series & CBC-300C Series Dual Channel Adjust Clutch/Brake Controls P-269-89-0408 Installation Installation & Operating Instructions Contents Introduction........................... 2 Specifications.........................

More information

SOLENOID VALVES AND PNEUMATIC VALVES

SOLENOID VALVES AND PNEUMATIC VALVES A S E R I E S Catalogue 001 Directly operated solenoid valves Series A / way, 3/ way monostable, stable (with magnetic memory) Ports M5, G1/8, cartridge ø 4 The Series A solenoid valves are of the directly

More information

GCU-10. Automatic Engine Control Unit Operators Manual

GCU-10. Automatic Engine Control Unit Operators Manual GCU-10 Automatic Engine Control Unit Operators Manual KUTAI ELECTRONICS INDUSTRY CO., LTD. TEL : +886-7-8121771 FAX : +886-7-8121775 Website : www.kutai.com.tw Headquarters : No.3, Lane 201, Chien Fu St.,

More information

Weighbatch. MultiVac. Operating Manual

Weighbatch. MultiVac. Operating Manual Weighbatch MultiVac Loading System Operating Manual MultiVac Operating Manual August 2007 2 Table of Contents INTRODUCTION 5 AT THE VERY LEAST, READ THIS! 6 PRINCIPLE OF OPERATION 7 Vacuum Pump 8 Loader

More information

Rental Industry Safety Tester Safe Check 5s

Rental Industry Safety Tester Safe Check 5s Rental Industry Safety Tester Safe Check 5s Feb 2006 2006 Clare Instruments Inc. Issue 2.0 Firmware Version : 1.2a Limited Warranty & Limitation of Liability Clare Instruments Inc, guarantees this product

More information

Actionpac LNS4. Panel Installation Datasheet. Actionpac LNS4 RELEASE 1.0 JUNE In partnership

Actionpac LNS4. Panel Installation Datasheet. Actionpac LNS4 RELEASE 1.0 JUNE In partnership Actionpac LNS4 Panel Installation Datasheet ELECTROSTATIC SENSITIVE DEVICE This product forms part of a life safety system. Failure to correctly store, handle, install and maintain the product will directly

More information

Data sheet. CI-TI TM Contactors and Motor Starters Circuit Breakers CTI B1427

Data sheet. CI-TI TM Contactors and Motor Starters Circuit Breakers CTI B1427 Data sheet CI-TI TM Contactors and Motor Starters Circuit Breakers November 2002 DKACT.PD.C00.L2.02 520B1427 Introduction Circuit breakers/manual motor starters cover the power ranges 0.09-12.5 kw This

More information

Pressure Transmitters

Pressure Transmitters Transmitters Wetted parts are all made of stainless steel for high resistance to chemicals Stainless steel diaphragm welded with casing No seals and thus low leakage rate even with difficult gases High

More information

PRECISION UK Ltd DUPLEX AGSS PLANT

PRECISION UK Ltd DUPLEX AGSS PLANT DUPLEX AGSS PLANT Contents Page Section Page Product Description General 3 AGSS Plant 3 AGSS Remote Switch 3 Operation General 4 Safety General 5 Installation General 5 Mechanical 5 Electrical 7 Wiring

More information

GLM SERIES CONTROL Users Manual Rev:

GLM SERIES CONTROL Users Manual Rev: GLM SERIES CONTROL Users Manual Rev: 808062 Connecting Power Page 2 Motor Terminal Wiring Diagrams Page 3 Getting Started / Setup Page 4 1. Obstruction Detection Devices Page 4 2. Checking Power and Direction

More information

CALTRAP INSTALLATION AND OPERATIONS MANUAL

CALTRAP INSTALLATION AND OPERATIONS MANUAL INSTALLATION AND OPERATIONS MANUAL NOTE Please read this entire installation and operations manual before energizing the. Safety Considerations: Installing and servicing capacitor equipment can be hazardous.

More information

Metrohm E3640 FLASH TESTER INSTRUCTION MANUAL. Martindale Electric Co Ltd.

Metrohm E3640 FLASH TESTER INSTRUCTION MANUAL. Martindale Electric Co Ltd. Metrohm Martindale Electric Metrohm House, Imperial Park, Imperial Way, Watford, Hertfordshire, WD24 4PP, UK T: 01923 441717 F: 01923 446900 Email: sales@martindale-electric.co.uk web: www.martindale-electric.co.uk

More information

FUSERBLOC CD. The universal Fuse Combination Switch FROM 20 TO 1250 A. Industrial Switching & Protection Systems

FUSERBLOC CD. The universal Fuse Combination Switch FROM 20 TO 1250 A. Industrial Switching & Protection Systems FUSERBLOC CD The universal Fuse Combination Switch FROM 20 TO 1250 A SOCOMEC GROUP SWITCHING PROTECTION & UPS Industrial Switching & Protection Systems SWITCHING FUSERBLOC CD THE UNIVERSAL FUSE COMBINATION

More information

27.6 Vdc 1 Amp Switch Mode Power Supply for Fire EN54-4:1997 +A1 +A2

27.6 Vdc 1 Amp Switch Mode Power Supply for Fire EN54-4:1997 +A1 +A2 1 27.6 Vdc 1 Amp Switch Mode Power Supply for Fire EN54-4:1997 +A1 +A2 STX2401-C STX2401-T FEATURES 0843-CPR-0213 14 Elmdene International Ltd Tel: +44(0)23 9269 6638 3 Keel Close, Interchange Park, Fax:

More information

XENON POWER SUPPLY 4000 Watt Gladiator IV

XENON POWER SUPPLY 4000 Watt Gladiator IV XENON POWER SUPPLY 4000 Watt Gladiator IV 220 Volt Equipment Type 62-00049 Rev. February 2003 STRONG INTERNATIONAL a division of Ballantyne of Omaha, Inc. 4350 McKinley Street Omaha, Nebraska 68112 USA

More information

Electrical operating instructions

Electrical operating instructions en Electrical operating instructions Reversing contactor universal 2 Contactor / 24V for three- and single- phase motor 51171134 - d 04.2009 OPERATING INSTRUCTIONS 52210115 consisting of: E : Electrical

More information

Zone 1 Linear Range - Installation Guide

Zone 1 Linear Range - Installation Guide Zone 1 Linear Range - Installation Guide CML14ATEX3119 & IEC Ex CML15.0001 This installation guide provides instructions for installing SPARTAN series of explosion protected Zone 1 Linear luminaires. Text

More information

KEWTECH. KT56 digital multi function tester. Instruction manual

KEWTECH. KT56 digital multi function tester. Instruction manual KEWTECH KT56 digital multi function tester Instruction manual Contents 1 Safety Notice 1 2 Features and Principles of Measurement 3 3 Introduction 6 4 Specifications 7 5 Instrument layout 9 6 Operating

More information

PowerOhm Installation Manual for BM R Series Braking Modules

PowerOhm Installation Manual for BM R Series Braking Modules PowerOhm Installation Manual for BM R Series Braking Modules IMPORTANT: These instructions should be read thoroughly before installation. All warnings and precautions should be observed for both personal

More information

M OTO R. The electric motor. DC - direct current voltage.

M OTO R. The electric motor. DC - direct current voltage. TMD-5 Lubricator Automatic Cyclic Before installing or operating this lubricator, please read this manual carefully. Failure to follow instructions can result in damage to the product and/or serious bodily

More information

The 4HR-UPS 220V ac output is provided via a Pure Sine Wave inverter, allowing it to be backed up by 2x 12V standby batteries.

The 4HR-UPS 220V ac output is provided via a Pure Sine Wave inverter, allowing it to be backed up by 2x 12V standby batteries. 1 Elmdene International Ltd Tel: +44 (0)23 9269 6638 3 Keel Close, Interchange Park, Fax: +44 (0)23 9266 0483 Portsmouth, Hampshire, PO3 5QD, UK Web: www.elmdene.co.uk STANDBY 220V AC POWER SYSTEM IDEAL

More information

Rescue Pac. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference

Rescue Pac. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference Please dispose of Packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate

More information

Application Engineering

Application Engineering Application Engineering February, 2009 Copeland Digital Compressor Controller Introduction The Digital Compressor Controller is the electronics interface between the Copeland Scroll Digital Compressor

More information

The EFL 2000/1 & 2 User Guide Test Sieve Shaker. Contents

The EFL 2000/1 & 2 User Guide Test Sieve Shaker. Contents The EFL 2000/1 & 2 User Guide Test Sieve Shaker ISSUE 04-02 Contents Description Page 1 Setting Up: 2-8 Unpacking 2 Assembly 3 Clamping Assembly 4 Electrical Connections 5 Sieve Stacking 6 8 Operating

More information

BATTERY CHARGER-STARTER

BATTERY CHARGER-STARTER BATTERY CHARGER-STARTER MODEL NO: WBC240 & WBC400 PART NO: 6261505 & 6261515 OPERATION & MAINTENANCE INSTRUCTIONS GC0116 INTRODUCTION Thank you for purchasing this CLARKE Battery Charger/Starter. Please

More information

USER GUIDE 12 V Lead acid batteries Ah

USER GUIDE 12 V Lead acid batteries Ah USER GUIDE 12 V Lead acid batteries 1-150 Ah GB 1 Thank you for choosing this charger from Exide Technologies Your new battery charger will enable you to keep your battery fully charged and will optimize

More information

OPERATING INSTRUCTION

OPERATING INSTRUCTION 11/05 Form #273 OPERATING INSTRUCTION MODEL 4105 Disital Earth Resistance Tester 2150 joshua's Path, Suite 302, Hauppauge, NY 11788 Phone : 1-800-645-5398 or 1-639-231-7050 Fax : 1-639-434-3128 E-mail

More information

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN SYMBOL LEGEND DANGER THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN WARNING THIS WARNS THAT MATERIALS MAY BE DAMAGED IF APPROPRIATE PRECAUTIONS ARE NOT

More information

Door Control Panel TS 960. instructions. (Design and functions subject to change) /

Door Control Panel TS 960. instructions. (Design and functions subject to change) / Electrical operating Operating instructions Door Control Panel TS 960 GB (Design and functions subject to change) 51171098 / 10.2002 OPERATING INSTRUCTIONS PAGE SAFETY DIRECTIONS...4 FUNCTION OVERVIEW...6

More information

HE-PSU(4.0) Power Supply & Battery Charger Installation, Commissioning & Operating Manual

HE-PSU(4.0) Power Supply & Battery Charger Installation, Commissioning & Operating Manual HE-PSU(4.0) Power Supply & Battery Charger Installation, Commissioning & Operating Manual Page 1 of 10 CONTENTS 1. GENERAL...2 2. POWER REQUIREMENTS...2 2.1 HE-PSU(4.0) Input/Output Electrical Ratings...2

More information

Installation instructions. Adapter AD 01 AD 02 AD 03

Installation instructions. Adapter AD 01 AD 02 AD 03 Installation instructions Adapter AD 0 AD 0 AD 03 Table of contents Safety information..... Meaning of safety symbols... General safety information... 3 Introduction... Operation... 3 3. 4 Operating faults...

More information

MAGNETIC MOTOR STARTERS

MAGNETIC MOTOR STARTERS Chapter 6 MAGNETIC MOTOR STARTERS 1 The basic use for the magnetic contactor is for switching power in resistance heating elements, lighting, magnetic brakes, or heavy industrial solenoids. Contactors

More information

VT Oil-Free Range Operators Handbook

VT Oil-Free Range Operators Handbook VT Oil-Free Range Operators Handbook Covering Models:- VT7 / VT7D VT10 / VT10D VT200 / VT200D VT300 / VT300D VT00 / VT00D BAMBI AIR COMPRESSORS LTD 12 Thimble Mill Lane Heartlands Birmingham B7 HT Tel:

More information

The Powermatic User Guide Test Sieve Shaker

The Powermatic User Guide Test Sieve Shaker The Powermatic User Guide Test Sieve Shaker ISSUE 04-02 Contents Description Page 1 Setting Up: 2-8 Unpacking 2 Assembly 3-4 Levelling 4 Electrical Connections 5 Sieve Stacking 6-8 Operating Instructions

More information

TPHK Series Immersible Pump

TPHK Series Immersible Pump TPHK Series Immersible Pump Instruction Manual ISO 9001 Certified WALRUS PUMP CO., LTD. EC Declaration of Conformity Manufacturer: Walrus Pump Co., Ltd. Address: No.83-14, Dapiantou, Sanzhi Dist., New

More information

Series A Electric Linear Actuators

Series A Electric Linear Actuators 3581650/3 IM-P358-11 CH Issue 3 Series A Electric Linear Actuators Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning 5. Maintenance

More information

MOTOR. The electric motor. DC - direct current voltage.

MOTOR. The electric motor. DC - direct current voltage. TMD-5 Lubricator Automatic Cyclic Before installing or operating this lubricator, please read this manual carefully. Failure to follow instructions can result in damage to the product and/or serious bodily

More information

Advantage-D. Operating Instructions and Maintenance Manual. Central Vacuum Systems (Expandable/Modular Models) (Ver.

Advantage-D. Operating Instructions and Maintenance Manual. Central Vacuum Systems (Expandable/Modular Models) (Ver. Advantage-D Series 3 Central Vacuum Systems (Expandable/Modular Models) (Ver. 8/05) Operating Instructions and Maintenance Manual DESCRIPTION The Becker Advantage-D and Advantage-L central vacuum systems

More information

Operating Instructions K Always on the safe side.

Operating Instructions K Always on the safe side. Operating Instructions K9 4953. Always on the safe side. KaVo Dental GmbH Wangener Straße 78 D-88299 Leutkirch Tel.: 0 75 61 / 86-150 Fax: 0 75 61 / 86-265 A 1 User information...2 A 1.1 Meaning of the

More information

PTB 14 ATEX 2023 X, EPS 16 ATEX 1046 X. Operating Instructions. Solenoid coil Type AC10 Magnetspule Typ AC10 Bobine magnétique Type AC10

PTB 14 ATEX 2023 X, EPS 16 ATEX 1046 X. Operating Instructions. Solenoid coil Type AC10 Magnetspule Typ AC10 Bobine magnétique Type AC10 PTB 14 ATEX 2023 X, EPS 16 ATEX 1046 X Solenoid coil Type AC10 Magnetspule Typ AC10 Bobine magnétique Type AC10 Device with II 2G/D Ex approval Geräte mit II 2G/D Ex Zulassung Appareils avec mode de protection

More information

HIB Enclosed Inverter User Guide

HIB Enclosed Inverter User Guide HIB Enclosed Inverter User Guide (0.75kW~22kW) V1.2.0 Contents 1 Safety information...1 2 Technical Data...2 3 Motor Connection...4 4 Operation...5 5 Single phase circuit diagram...7 6 Three phase circuit

More information

1 This instrument must only be used by a competent and trained person and operated in strict accordance with the instructions.

1 This instrument must only be used by a competent and trained person and operated in strict accordance with the instructions. 1 This instrument must only be used by a competent and trained person and operated in strict accordance with the instructions. KYORITSU will not accept liability for any damage or injury caused by misuse

More information

University of Houston Master Construction Specifications Insert Project Name SECTION ELECTRONIC VARIABLE SPEED DRIVES PART 1 - GENERAL

University of Houston Master Construction Specifications Insert Project Name SECTION ELECTRONIC VARIABLE SPEED DRIVES PART 1 - GENERAL SECTION 23 04 10 ELECTRONIC VARIABLE SPEED DRIVES PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Division 1, "General Requirements", and Section

More information