KPSE High performance crimp contact connectors. 1 Standard MIL-C mates with any connector designed to MIL-C and VG

Transcription

1

2 26482 eries onnectors igh performance crimp contact connectors igh performance crimp contact connectors igh performance rimp termination losed entry socket contacts eries environmental, miniature circular, quick disconnect connectors are designed for the exacting requirements of today s electronic industry. They are intermateable, intermountable and interchangeable with all connectors manufactured acc. to and V tandard mates with any connector designed to and V rimp, snapin contacts are designed to and can be crimped with the standard 22520/1 crimp tool. losedentry socket contacts eliminate damage from abuse by test probes and help to correct any misaligned pins during engagement ontact insertion is accomplished from the rear of the connector. When the contact is fully inserted, the clip tines snap securely behind the contact shoulder. ontact extraction is accomplished with a frontinserted tool. ressing the tool plunger pushes the contact out through the rear of the connector. 3 onobloc insulator does not leave any access to moisture and avoids interfacial empty space. 4 ontact retaining clip is completely encased in a tough plastic wafer to protect the clip from damage omplete moisture sealing is achieved by combining four seals: shell, peripheral, interfacial and wire seals hell eal is effected when the plug shell pushes against the sealing ring in the receptacle when the connectors are mated. eripheral eal around the edge of the pin insulator is designed so that mating the connector puts tension on the seal and greatly reduces compression set. nterfacial eal is achieved by the insutor faces meeting when the plug and receptacle are mated. Wire eal is accomplished by a multiple ripple design, exceeding the wire sealing requirements of ositive inserttoshell mechanical retention with hard plastic wafer firmly locked into a groove in the shell, in addition to a strong adhesive bond between the insert and shell. 39

3 26482 eries onnectors igh performance crimp contact connectors ow to order X * X * X TY Z OTT T OTT TY TT T OTO OTO O X TT annon prefix TT annon o prefix prefix TY TT annon designation 00 wall mounting receptacle 01 cable connecting plug 02 box mounting receptacle (class only) 06 straight plug 07 jam nut receptacle 08 90º angle plug TO 3120 Wall mounting receptacle 3121 able connecting receptacle 3122 ox mounting receptacle 3124 Jam nut receptacle 3126 traight plug general duty (not approved) general duty with strain relief (not approved) with a grommet seal ( specification) grommet seal with strain relief ( specification) J gland seal with strain relief for jacketed cable (U.. version) (not approved) for potting ( specification) (U.. version) Z 8, 10, 12, 14, 16, 18, 20, 22, and 24 OTT T see page 41 OTT TY in ocket TT T OTO W, X, and Z (omit for normal), see page 42 OTO O (nclude ame odes as T) 34 lectroless nickel hardware, o compliant (uropean version) 71 lectroless nickel hardware (U.. version o compliant after 11/1/07)) 206 lack zinc cobalt hardware (U.. version, o compliant) 232 lack zinc cobalt hardware (uropean version, o compliant) 233 reen zinc cobalt hardware (uropean version) 408 xtended ife ontact old over ickel hrink boot adapter for shell styles 00, 01, 06 and 07 (lass only) Z ndbell for shielding braids and shrink boots. (lass only) 07 lear chromate over cadmium hardware (U.. version) 16 anyard release (applicable to plug only) (U.. version) 23 round springs (applicable to plug only) 42 connectors without endbell and related parts 9 = 9 for shell #10 12 = 12x1,5 for shell #10 11 = 11 for shell #12 16 = 16x1,5 for shell #12 13 = 13,5 for shell #14 20 = 20x1,5 for shell #14 16 = 16 for shell #16 25 = 25x1,5 for shell #16 21 = 21 for shell #18 25 = 25x1,5 for shell #18 21 = 21 for shell #20 25 = 25x1,5 for shell #20 21 = 21 for shell #22 32 = 32x1,5 for shell #22 29 = 29 for shell #24 32 = 32x1,5 for shell #24 onsult factory for other modifications. Omit first digit (0) of shell style indication when using a modification code. 40

4 26482 eries onnectors ontact rrangements T uthorized per (VY) ot approved TT proprietary V95328 hell ize o. of ontacts ervice ating hell ize #20 rawing not to scale; face view of pin insert shown (socket view is opposite) 83 3# # # #20 hell ize 10 hell ize 12 hell ize 14 J J J J hell ize o. of ontacts ervice ating 107 7# # # # # # # # #20 4# #20 1#16 hell ize 16 hell ize 18 J T U U V J T Y X Z T W U V J T U a b V Z c Y X W J T Y Z U X V W J J T U V d W c e b X a Y Z J hell ize o. of ontacts ervice ating # # #12 1# OX 1884 (ot for eceptacle hell tyle 02) 168 8# #20 1# # #20 2# # #20 2#16 T d e U c f V b a W Y Z X J T d c e U V f W i g X h Y b Z a J hell ize 20 J X W Y Z J V U T V W X U j Y T i k Z r h m a g q n b f p c e d J W V X j Y U k Z i T s m a h n r l b g q p f c e d J hell ize o. of ontacts ervice ating #20 1# # # #12* *ote: ontacts are 1 rounding in & 4 tandard ize 12 pins # #20 2# #20 hell ize 22 W X V J U T b a h c i Z T g d Y f e U J X V W T U e V d k f W c j i g X h b Y a Z J 206* T U V f g h W e m n i X d l k Y c Z b a J Y X Z W k a V j m b s n U i l c T r p h q d g e f J U T V W m n p X k q Y z r j Z y s i a x t h w u b g v c f d e J hell ize o. of ontacts ervice ating # # # # #20 14# #20 hell ize 24 Z a b Y t c X s u d W r v e w V q f U JJ x T p y g z n h i m k J Z a Y b X u v c t W d s w e V x JJ r f U y q g T z h p n i J m k j hell ize o. of ontacts ervice ating #20 2# #20 41

5 26482 eries onnectors lternate nsert ositions ace view of pin inserts W* X* Z* The five positions (W,X,Y,Z and ormal) differ in degree or rotation for various sizes and arrangements Y* o. of hell rr. egrees of otation ontacts ize o. W X Y Z * ** ** ** ** * * ** ** ** ** * ** ** ** ** * * * * ontact arrangements not qualified ot available in,,, J and are connector overall lengths 42

6 26482 eries onnectors Wall ounting eceptacles 3110 ( service class,,j,) 3120 ( service class,,) T00 00 TTO Y O T00/3110 Q Thd. TTO Y Q T OT O TY & OT O TY,, J & 00/3120 OZ OOV (T) T Y T 4 T O.140 X hell (+.79) * T Q Thread ize ±.003 (±.08) ±.016 (±.41).000 (.00) (T) ax. ±.005 (±.13) lass (11.96).062 (1.57).431 (10.95).594 (15.09).828 (21.03).120 (3.05) 7/1628U (14.96).062 (1.57).431 (10.95).719 (18.26).954 (24.23).120 (3.05) 9/1624U (19.00).062 (1.57).431 (10.95).812 (20.62) (26.59).120 (3.05) 11/1624U (22.17).062 (1.57).431 (10.95).906 (23.01) (28.98).120 (3.05) 13/1620U (25.35).062 (1.57).431 (10.95).969 (24.61) (31.34).120 (3.05) 15/1620U (28.52).062 (1.57).431 (10.95) (26.97) (33.73).120 (3.05) 11/1618U (31.70).094 (2.39).556 (14.12) (29.36) (36.91).120 (3.05) 13/1618U (34.87).094 (2.39).556 (14.12) (31.75) (40.08).120 (3.05) 15/1618U (38.05).094 (2.39).589 (14.96) (34.92) (43.26).147 (3.73) 17/1618U ot available in *(T) located within.010 T.. with respect to diameter and master keyway. eceptacles with Termination ssemblies V T J.395 (10.03) TY TY J J TY TY J TY J TY TY and TY hell V Thread ize in. ax. lass 2 in. ax. ax. ax. ax (8.51) 1.58 (40.00) 1/228U.115 (2.92).828 (21.03) (48.82).608 (15.44) (33.73) (11.84) 1.58 (40.00) 5/824U.178 (4.52).891 (22.63) (48.82).734 (18.64) (33.73) (15.01) 1.58 (40.00) 3/420U.302 (7.67) (25.81) (48.82).858 (21.79) (33.73) (17.90) 1.58 (40.00) 7/820U.365 (9.27) (28.98) (48.82).984 (24.99) (33.73) (21.08) 1.58 (40.00) 120U.490 (12.45) (30.56) (51.99) (28.19) (33.73) (24.08) 1.58 (40.00) 13/1618U.615 (15.62) (37.31) (52.78) (31.34) (33.73) (26.49) (43.89) 13/1618U.615 (15.62) (37.31) (59.54) (34.54) (38.89) (30.43) (43.89) 17/1618U.740 (18.80) (42.06) (34.14) (37.69) (38.89) (32.84) (44.15) 17/1618U.790 (20.07) (44.45) (61.11) (40.49) (40.49) TY J TY hell J J J ize ax./in. ax. ax. ax. in. ax /.168 (5.84/4.27).828 (21.03) (57.68).608 (15.44).317 (8.05) (36.91) /.205 (7.92/5.21).891 (22.63) (57.68).734 (18.64).434 (11.02) (36.91) /.338 (11.23/8.59) (25.81) (61.24).858 (21.79).548 (13.92) (36.91) /.416 (13.56/10.57) (28.98) (66.01).984 (24.99).673 (17.09) (36.91) /.550 (15.65/13.97) (30.56) (74.75) (28.19).798 (20.27) (36.91) /.600 (17.07/15.24) (37.31) (80.57) (31.34).899 (20.83) (36.91) /.634 (18.97/16.13) (37.31) (91.69) (34.54) (26.01) (42.47) /.670 (21.49/17.02) (42.06) (95.66) (37.69) (29.18) (42.47) /.740 (22.71/18.80) (44.45) (101.22) (40.89) (32.36) (44.04) ot available in,,, J and are connector overall lengths 43

7 26482 eries onnectors able onnecting lugs 3111 ( service class,,j,) 3121 ( service class,,) T01 01 TTO Y ia. O T01/3111 Q T ia. TTO Y OT O TY,, J & Q T 01/3121 OT O TY & U Y OZ OOV hell J (+.79) Y Q Thread ize ±.003 (±.08) ±.016 (±.41).000 (.00) ax. ax. lass (11.96).094 (2.39).400 (10.16).828 (21.03).958 (24.33) 7/1628U (14.94).094 (2.39).400 (10.16).954 (24.23) (27.48) 9/1624U (19.00).094 (2.39).400 (10.16) (26.59) (29.87) 11/1624U (22.17).094 (2.39).400 (10.16) (24.99) (32.26) 13/1620U (25.35).094 (2.39).400 (10.16) (28.98) (34.65) 15/1620U (28.52).094 (2.39).400 (10.16) (31.34) (37.03) 11/1618U (31.70).115 (2.92).535 (13.59) (33.73) (40.18) 13/1618U (34.87).115 (2.92).535 (13.59) (40.08) (43.38) 15/1618U (38.05).115 (2.92).558 (14.43) (43.26) (46.53) 17/1618U Y ia. ot available in *(T) located within.010 T.. with respect to diameter and master keyway. able onnecting lugs with Termination ssemblies V T J.395 (10.03) TY TY TY TY J J J TY J TY TY and TY hell V Thread ize in. ax. lass 2 in. ax. ax. ax. ax (8.51) 1.50 (38.00) 1/228U.115 (2.92).828 (21.03) (48.82).608 (15.44) (33.73) (11.84) 1.50 (38.00) 5/824U.178 (4.52).891 (22.63) (48.82).734 (18.64) (33.73) (15.01) 1.50 (38.00) 3/420U.302 (7.67) (25.81) (48.82).858 (21.79) (33.73) (17.90) 1.50 (38.00) 7/820U.365 (9.27) (28.98) (48.82).984 (24.99) (33.73) (21.08) 1.50 (38.00) 120U.490 (12.45) (30.56) (51.99) (28.19) (33.73) (24.08) 1.50 (38.00) 13/1618U.615 (15.62) (37.31) (52.78) (31.34) (33.73) (26.49) (43.89) 13/1618U.615 (15.62) (37.31) (59.54) (34.54) (38.89) (30.43) (43.89) 17/1618U.740 (18.80) (42.06) (34.14) (37.69) (38.89) (32.84) (44.15) 17/1618U.790 (20.07) (44.45) (61.11) (40.49) (40.49) TY J TY hell J J J ize ax./in. ax. ax. ax. in. ax /.168 (5.84/4.27).828 (21.03) (57.68).608 (15.44).317 (8.05) (36.91) /.205 (7.92/5.21).891 (22.63) (57.68).734 (18.64).434 (11.02) (36.91) /.338 (11.23/8.59) (25.81) (61.24).858 (21.79).548 (13.92) (36.91) /.416 (13.56/10.57) (28.98) (66.01).984 (24.99).673 (17.09) (36.91) /.550 (15.65/13.97) (30.56) (74.75) (28.19).798 (20.27) (36.91) /.600 (17.07/15.24) (37.31) (80.57) (31.34).899 (20.83) (36.91) /.634 (18.97/16.13) (37.31) (91.69) (34.54) (26.01) (42.47) /.670 (21.49/17.02) (42.06) (95.66) (37.69) (29.18) (42.47) /.740 (22.71/18.80) (44.45) (101.22) (40.89) (32.36) (44.04) 44

8 26482 eries onnectors ox ounting eceptacles 3112 ( service class ) 3122 ( service class ) T02 02 OZ OOV T 4 T O Z O T02/ /3122 (T) T Y.140 X ote: onnector does not accomodate backshell. hell (+.79) ia. * T Z ize ±.003 (±.08) ax. ±.016 (±.41) ax..000 (.00) ax. (T) ax. ±.005 ax (11.96).978 (24.84).062 (1.57) (33.07).431 (10.95).469 (11.91).594 (15.09).828 (21.03).120 (3.05).354 (8.99) (14.96).978 (24.84).062 (1.57) (33.07).431 (10.95).593 (15.06).719 (18.26).954 (24.23).120 (3.05).354 (8.99) (19.00).978 (24.84).062 (1.57) (33.07).431 (10.95).719 (18.26).812 (20.62) (26.59).120 (3.05).354 (8.99) (22.17).978 (24.84).062 (1.57) (33.07).431 (10.95).843 (21.41).906 (23.01) (28.98).120 (3.05).354 (8.99) (25.35).978 (24.84).062 (1.57) (33.07).431 (10.95).969 (24.61).969 (24.61) (31.34).120 (3.05).354 (8.99) (28.52).978 (24.84).062 (1.57) (33.07).431 (10.95) (27.76) (26.97) (33.73).120 (3.05).354 (8.99) (31.70) (30.38).094 (2.39) (34.72).556 (14.12) (30.96) (29.36) (36.91).120 (3.05).417 (10.59) (34.87) (30.38).094 (2.39) (34.72).556 (14.12) (34.11) (31.75) (40.08).120 (3.05).417 (10.59) (38.05) (30.38).094 (2.39) (36.02).589 (14.96) (37.31) (34.92) (43.26).147 (3.73).445 (11.30) ot available in *(T) located within.010 T.. with respect to diameter and master keyway. 45

9 26482 eries onnectors traight lugs 3116 ( service class,,j,) 3126 ( service class,,) T06 06 O T06/3116 Q T OZ OOV TTO Y 06/3126 Q T OT O TY,, J & OT O TY & hell ia. J Q Thread ize ax. ax. ±.010 (±0.25) lass (19.43).782 (19.86).353 (8.99) 7/1628U (21.34).926 (23.52).353 (8.99) 9/1624U (25.38) (26.49).353 (8.99)) 11/1624U (28.93) (30.05).353 (8.99) 13/1620U (32.03) (33.15).353 (8.99) 15/1620U (33.96) (35.33).353 (8.99) 11/1618U (37.52) (38.89).415 (10.54) 13/1618U (40.69) (42.06).415 (10.54) 15/1618U (43.76) (45.14).415 (10.54) 17/1618U ot available in traight lugs with Termination ssemblies V T J.395 (10.03) TY TY J J TY TY J TY J TY TY and TY hell V Thread ize in. ax. lass 2 in. ax. ax. ax. ax (8.51) (36.58) 1/228U.115 (2.92).828 (21.03) (48.41).608 (15.44) (33.73) (11.84) (36.58) 5/824U.178 (4.52).891 (22.63) (48.41).734 (18.64) (33.73) (15.01) (36.58) 3/420U.302 (7.67) (25.81) (48.41).858 (21.79) (33.73) (17.90) (36.58) 7/820U.365 (9.27) (28.98) (48.41).984 (24.99) (33.73) (21.08) (36.58) 120U.490 (12.45) (30.56) (51.99) (28.19) (33.73) (24.08) (42.21) 13/1618U.615 (15.62) (37.31) (52.78) (31.34) (33.73) (26.49) (42.21) 13/1618U.615 (15.62) (37.31) (57.15) (34.54) (36.91) (30.43) (42.21) 17/1618U.740 (18.80) (42.06) (57.15)) (37.69) (36.91) (32.84) (42.47) 17/1618U.790 (20.07) (44.45) (58.72) (40.49) (38.54) TY J TY hell J J J ize ax./in. ax. ax. ax. in. ax /.168 (5.84/4.27).828 (21.03) (57.68).608 (15.44).317 (8.05) (38.10) /.205 (7.92/5.21).891 (22.63) (57.68).734 (18.64).434 (11.02) (38.10) /.338 (11.23/8.59) (25.81) (61.24).858 (21.79).548 (13.92) (38.10)) /.416 (13.56/10.57) (28.98) (66.01).984 (24.99).673 (17.09) (38.10) /.550 (15.65/13.97) (30.56) (74.75) (28.19).798 (20.27) (38.10) /.600 (17.07/15.24) (37.31) (80.57) (31.34).899 (20.83) (38.10) /.634 (18.97/16.13) (37.31) (91.69) (34.54) (26.01) (40.87) /.670 (21.49/17.02) (42.06) (95.66) (37.69) (29.18) (40.87) /.740 (22.71/18.80) (44.45) (101.22) (40.89) (32.36) (42.85) ot available in,,, J and are connector overall lengths 46

10 26482 eries onnectors Jam ut eceptacles 3114 ( service class,,) 3124 ( service class,,) T07 07 T T O T07/3114 Q T T T T OT O TY & OT O TY,& T hell (+.08) anel Thickness Thread ize ±.003 (±.08) ±.005 (0.130) ±.017 (±.43) ±.020 (±.05).000 (.00) ax. ax. in. ax. lass (11.96).525 (13.34).750 (19.05).117 (2.97).691 (17.55) (27.38).954 (15.09).062 (1.57).125 (3.17) 9/1624U (14.96).650 (16.51).875 (22.22).117 (2.97).691 (17.55) (30.56) (27.38).062 (1.57).125 (3.17) 11/1624U (19.00).813 (20.65) (26.97).117 (2.97).691 (17.55) (35.33) (32.16).062 (1.57).125 (3.17) 7/820U (22.17).937 (23.80) (30.17).117 (2.97).691 (17.55) (38.51) (35.33).062 (1.57).125 (3.17) 120U (25.35) (26.95) (33.32).117 (2.97).691 (17.55) (41.68) (38.51).062 (1.57).125 (3.17) 11/818U (28.52) (30.12) (36.25).117 (2.97).691 (17.55) (44.86) (41.68).062 (1.57).125 (3.17) 11/418U (31.70) (33.30) (39.67).148 (3.76).879 (22.33) (49.63) (46.43).062 (1.57).250 (6.35) 13/818U (34.87) (36.47) (42.87).148 (3.76).879 (22.33) (52.78) (49.63).062 (1.57).250 (6.35) 11/218U (38.05) (39.65) (46.02).148 (3.76).912 (23.16) (55.96) (52.78).062 (1.57).250 (6.35) 15/818U ot available in Jam ut eceptacles with Termination ssemblies TY (o Term. ssy.) Z TY TY and TY TY hell Z ize ax. ax. in. ax. ax. ax. ax. in. ax (7.92).828 (21.03).115 (2.92) (48.41).655 (16.64) (34.14).608 (15.44).317 (8.05) (35.33) (7.92).891 (22.63).178 (4.52) (48.41).843 (21.41) (34.14).734 (18.64).434 (11.02) (35.33) (7.92) (25.81).302 (7.67) (48.41).968 (24.59) (34.14).858 (21.79).548 (13.92) (35.33) (7.92) (28.98).365 (9.27) (48.41) (27.76) (34.14).984 (24.99).673 (17.09) (35.33) (7.92) (30.56).490 (12.45) (51.99) (30.94) (34.14) (28.19).798 (20.27) (35.33) (7.92) (37.31).615 (15.62) (52.78) (34.11) (34.14) (31.34).899 (22.83) (35.33) (4.90) (37.31).615 (15.62) (59.13) (38.10) (40.49) (34.54) (26.01) (41.68) (4.90) (42.06).740 (18.80) (59.13) (41.28) (40.49) (37.69) (29.18) (41.68) (3.81) (44.45).790 (20.07) (62.31) (44.45) (41.68) (40.89) (32.36) (43.26),, and are connector overall lengths. 47

11 26482 eries onnectors ight ngle lugs T08/08 Q T OZ O Q T OT O TY & OT O TY,,J& T08 08 T/ hell ia. Q Thread ize ax. ax. lass (19.43).782 (19.86) 7/1628U (22.00).926 (23.52) 9/1624U (26.20) (26.49) 11/1624U (29.40) (30.05) 13/1620U (32.80) (33.15) 15/1620U (35.40) (35.33) 11/1618U (39.00) (38.89) 13/1618U (42.10) (42.06) 15/1618U (45.20) (45.14) 17/1618U ot available in OT: for size 10 and 24 consult factory for availability in type,, and. or size 8 consult factory for availability in Type. ight ngle lugs with Termination ssemblies V T X TY and TY and TY hell V Thread ize ax. ax. lass 2 ax. ax. ax. ax. in. ax (36.09).822 (20.88) 1/228U (31.44) (36.09) (46.79) () () () (37.69).853 (21.67) 5/828U (32.24) (37.69) (49.20) (26.16) (35.05).252 (6.40) (39.27).916 (23.27) 3/420U (35.43) (39.27) (53.10) (26.16) (39.80).252 (6.40) (40.05).978 (24.84) 7/820U (38.58) (40.05) (55.20) (26.16) (39.80).283 (7.19) (40.87) (26.44) 120U (40.18) (40.87) (56.85) (32.51) (39.80).355 (9.02) (44.04) (28.70) 13/1618U (41.76) (44.04) (62.35) (32.51) (44.58).530 (13.46) (47.73) (29.62) 13/1618U (43.36) (47.73) (66.78) (38.86) (45.26).562 (14.27) (51.69) (31.62) 17/1618U (47.85) (51.69) (71.51) (38.86) (45.26).562 (14.27) (51.69) (33.58) 17/1618U (49.86) (51.69) (73.70) (45.21) (53.01).610 (15.49) ot available in. OT: or size 10 and 24 consult factory for availability in type,, and. or size 8 consult factory for availability in Type. 48

12 26482 eries onnectors igh performance crimp contact connectors TO ow to order acc. to V TO TY Z OTT T OTT TY TT T OTO TY wall mounting receptacle with straight endbell wall mounting receptacle with cable clamp box mounting receptacle jam nut receptacle jam nut receptacle with cable clamp J straight plug with adapter straight plug with cable clamp straight plug, version Z straight plug jam nut receptacle with adapter T jam nut receptacle, version Z V Z 8, 10, 12, 14, 16, 18, 20, 22, and 24 OTT T see page 41 OTT TY in ocket TT T OTO see page 42 ow to Order T Thruulkhead eceptacle onnectors eneral urpose ouble ended pin and socket contacts ontains T socket insert onremovable contacts T connectors are a series of general purpose, miniature circular connectors, qualified for use in military applications. They are also widely used in industrial applications. The T in a thrubulkhead version with double faced pin and socket insert construction allowing mating from both ends. They contain T Y X Z OTT T OTT TY (pin & socket) TT T OTO T socket inserts with feedthru (pin/socket) nonremovable contacts. The thrubulkhead receptacle is provided for applications requiring the disconnection of a power source from either side of a panel. typical connector to be used if air leakage requirements are critical Y X Z OTT T TT T OTO 3119 ( service class ) T ( service class ) T *(T..) located within.010 T.. with respect to the diameter and master keyway. OZ OOV.140. X. (T) TY T. 4 T. O hell ia (+.79) * T ize ±.003 (±.08) ±.016 (±.406) ax..000 (.00) (T) ax. ±.005 (±.127) (11.96).062 (1.57) (28.58).562 (14.27).594 (15.09) 7/1628U.120 (3.05) (14.94).062 (1.57) (28.58).562 (14.27).719 (18.26) 9/1624U.120 (3.05) (19.00).062 (1.57) (28.58).562 (14.27).812 (20.62) 11/1624U.120 (3.05) (22.17).062 (1.57) (28.58).562 (14.27).906 (23.01) 13/1620U.120 (3.05) (25.35).062 (1.57) (28.58).562 (14.27).969 (24.61) 15/1620U.120 (3.05) (28.52).062 (1.57) (28.58).562 (14.27) (26.97) 11/1618U.120 (3.05) (31.70).094 (2.39) (35.71).688 (17.48) (29.36) 13/1618U.120 (3.05) (34.87).094 (2.39) (35.71).688 (17.48) (31.76) 15/1618U.120 (3.05) (38.05).094 (2.39) (35.71).688 (17.48) (34.92) 17/1618U.147 (3.73) 49

13 26482 eries onnectors ummy eceptacles ow To Order T X UY T TO Z OTO X T TT annon refix Z 8 TU 24 OTO oneolive drab chromate over cadmium.140. ax 4 O OT: or Version and additional finishes see V catalog J hell (.79) ize ±.003 (.08) asic ax. ±.005 (.13).000 (.00) ±.016 (.41) (11.96).594 (15.09).828 (21.03).120 (3.05).462 (11.73).062 (1.57) (14.94).719 (18.26).954 (24.23).120 (3.05).462 (11.73).062 (1.57) (19.00).812 (20.62) (26.60).120 (3.05).462 (11.73).062 (1.57) (22.17).906 (23.01) (28.98).120 (3.05).462 (11.73).062 (1.57) (25.35).969 (24.61) (31.34).120 (3.05).462 (11.73).062 (1.57) (28.52) (26.97) (33.73).120 (3.05).462 (11.73).062 (1.57) (31.70) (29.36) (36.91).120 (3.05).556 (14.12).094 (2.39) (34.87) (31.75) (40.08).120 (3.05).556 (14.12).094 (2.39) (38.05) (34.93) (43.26).147 (3.73).589 (14.96).094 (2.39). J rotective aps ow To Order T X 80 ap for plugs 81 ap for receptacle TY Z TTO TY.047 (1.19) ax..169 (4.29) ±.008 (.20).094 (2.39) ax. Q Q OTO X T TT annon refix (12.7).250 (6.35) T (12.7).250 (6.35) T (12.7).250 (6.35) T TY 80 lug ap 81 eceptacle ap Z 8 TU 24 TTO TY ash hain ash hain with ing OT: or version and additional finishes see V catalog. hell (.79) Q ize ±.003 (.08) ax. ax..000 (.00) in. ax. ax (11.96).719 (18.26) (76.20).562 (14.27).368 (9.35).578 (14.68).734 (18.64).562 (14.27) (14.94).844 (21.44) (76.20).562 (14.27).368 (9.35).703 (17.86).859 (21.82).562 (14.27) (19.00) (25.40) (88.90).562 (14.27).368 (9.35).891 (22.63) (25.40).562 (14.27) (22.17) (28.58) (88.90).562 (14.27).368 (9.35) (25.81) (28.58).562 (14.27) (25.35) (31.75) (88.90).562 (14.27).368 (9.35) (28.98) (31.75).562 (14.27) (28.52) (34.93) (88.90).562 (14.27).368 (9.35) (32.16) (34.93).562 (14.27) (31.70) (38.10) (101.60).625 (15.88).430 (10.92) (35.33) (38.10).562 (14.27) (34.87) (41.26) (101.60).625 (15.88).430 (10.92) (38.51) (41.26).562 (14.27) (38.05) (44.45) (101.60).658 (16.71).463 (11.76) (41.68) (44.45).602 (15.29) T and rotective ap ash hain ing/ivet asket T aluminum alloy, olive drab finish per QQ416 stainless steel stainless steel polychloroprene 50

14 26482 eries onnectors eceptacles with rinted ircuit oard ontacts ow to order T W X TY Z OTT T OTT TY TT T OTO OTO O X T TT annon designation OTT T see page 41 TY TT annon designation 2 box mounting receptacle (class only) 7 jam nut receptacle general duty (shell type 7 only) shell type 2 only Z 8, 10, 12, 14, 16, 18, 20, 22, and 24 ote: onsult factory for custom Tail configurations OTT TY in ocket TT T OTO W, X, and Z (omit for normal position) OTO O (see following page for description) V T2 with tail contacts.025 ±.001 dia. size ±.001 dia. size 16 X T2/ T7 with tail contacts.76 mm dia. size 16 and size 20 W T2/ T7 with tail contacts.6mm dia. size 16 and size 20 51

15 26482 eries onnectors T onnectors with.. Tail ontacts T2V.. Tail diameter.. contacts to extend.600" ±.032" from rear of shell flange... tail extension from the rear of the shell flange ontact ize ±.001 iameter ±.001 iameter ontact factory for additional requirements. ox ounting eceptacle T2 W/X hell ize ,03 0,13 12,00 15,00 19,05 22,23 25,40 28,58 31,75 34,93 38,10 +0,25 13,50 13,50 13,50 13,50 13,50 13,50 16,50 16,50 17,30 max. 21,1 21,1 21,1 21,1 21,1 21,1 22,7 22,7 22,7 ±0,15 11,60 11,60 11,60 11,60 11,60 11,60 14,25 14,25 15,10 max. 11,10 14,30 17,50 20,60 23,80 27,00 30,20 33,40 36,50 ±0,15 15,10 18,30 20,60 23,00 24,60 27,00 29,40 31,70 34,90 max. 21,00 24,20 26,60 29,00 31,30 33,70 36,90 40,10 43,30 Ø T ±0,15 3,05 3,05 3,05 3,05 3,05 3,05 3,05 3,05 3,75 Jam ut eceptacle T7 W/X hell ize* ,03 0,13 12,00 15,00 19,05 22,23 25,40 28,58 31,75 34,93 38,10 +0,15 13,3 16,5 20,6 23,8 26,9 30,1 33,3 36,5 39,6 ±0,15 19,0 22,2 27,0 30,2 33,3 36,5 39,7 42,9 46,0 ±0,25 3,2 3,2 3,2 3,2 3,2 3,2 4,0 4,0 4,0 ±0,15 17,7 17,7 17,7 17,7 17,7 17,7 22,5 22,5 23,3 Thread Type 2 9/1624U 11/1624U 7/820U 120U 11/818U 11/418U 13/818U 11/218U 15/818U ±0,5 2,40 2,70 3,20 3,50 3,85 4,15 4,60 4,95 5,25 anel Thickness min. 1,6 1,6 1,6 1,6 1,6 1,6 1,6 1,6 1,6 Y max. 28,0 31,0 36,0 39,0 42,0 45,0 50,0 55,0 57,0 52

16 26482 eries onnectors pecial Versions with rounding ontinuity These connectors are designed for ensuring continuity. t the cable shielding level (to protect it against radio frequency interferences) t the grounding level (if it is connected to the shielding) The plugs are manufactured with grounding fingers soldered to the front face of the shell. They make contact with the inner side of the receptacle shell. lug and receptacle feature a special endbell which supports the cable shielding. The connectors are in accordance with the V specification. eceptacle with rounding ontinuity (for shielded cable) T/ 0...Z T hell øt ize in ax ±0.25 ax. ±0.15 ±0.15 ax. ± (12.00).360 (6.6).630 (16.0).524 (13.3).590 (15.0).531 (13.5) (52.0).457 (11.6).594 (15.1).827 (21.0).120 (3.05) (15.00).362 (9.2).709 (18.0).634 (16.1).590 (15.0).531 (13.5) (52.0).457 (11.6).720 (18.3).953 (24.2).120 (3.05) (19.05).480 (12.2).866 (22.0).787 (20.0).669 (17.0).531 (13.5) (62.0).457 (11.6).811 (20.6) (26.6).120 (3.05) (22.23).598 (15.2).984 (25.0).874 (22.2).709 (18.0).531 (13.5) (62.0).457 (11.6).905 (23.0) (29.0).120 (3.05) (25.40).720 (18.3) (28.0) (26.2).709 (18.0).531 (13.5) (62.0).457 (11.6).968 (24.6) (31.3).120 (3.05) (28.58).787 (20.0) (32.0) (28.5).709 (18.0).531 (13.5) (62.0).457 (11.6) (27.0) (33.7).120 (3.05) (31.75).905 (23.0) (34.0) (32.5).709 (18.0).650 (16.5) (62.0).561 (14.25) (29.4) (36.9).120 (3.05) (34.93) (26.0) 1.50 (38.0) (34.8).709 (18.0).650 (16.5) (62.0).561 (14.25) (31.7) (40.1).120 (3.05) (38.10) (28.8) (41.0) (37.9).709 (18.0).681 (17.3) (62.0).594 (15.1) (34.9) (43.3).148 (3.75) n series only contact arrangements 83 and 833 available 53

17 26482 eries onnectors able onecting lug with rounding ontinuity (for shielding cable) T/ 1...Z Y hell øy ize in ax. ±1.0 ±0.25 ax. ±0.15 ax. ax (12.00).360 (6.6).630 (16.0).524 (13.3).590 (15.0).531 (13.5) (52.0).457 (11.6).728 (18.5).827 (21.0) (15.00).362 (9.2).709 (18.0).634 (16.1).590 (15.0).531 (13.5) (52.0).457 (11.6).905 (23.0).953 (24.2) (19.05).480 (12.2).866 (22.0).787 (20.0).669 (17.0).531 (13.5) (62.0).457 (11.6) (29.0) (26.6) (22.23).598 (15.2).984 (25.0).874 (22.2).709 (18.0).531 (13.5) (62.0).457 (11.6) (29.5) (29.0) (25.40).720 (18.3) (28.0) (26.2).709 (18.0).531 (13.5) (62.0).457 (11.6) (32.0) (31.3) (28.58).787 (20.0) (32.0) (28.5).709 (18.0).531 (13.5) (62.0).457 (11.6) (35.0) (33.7) (31.75).905 (23.0) (34.0) (32.5).709 (18.0).650 (16.5) (62.0).561 (14.25) (38.5) (36.9) (34.93) (26.0) 1.50 (38.0) (34.8).709 (18.0).650 (16.5) (62.0).561 (14.25) (42.0) (40.1) (38.10) (28.8) (41.0) (37.9).709 (18.0).681 (17.3) (62.0).594 (15.1) (46.0) (43.3) n series only contact arrangements 83 and 833 available T/ 6...Z traight lug with rounding ontinuity hell ize in ax. ax. ±1.0 ax. ± (6.6).630 (16.0).752 (19.1) (20.0).590 (15.0) (48.0).669 (17.0) (9.2).709 (18.0).866 (22.0) (15.0).590 (15.0) (48.0).748 (19.0) (12.2).866 (22.0) (26.2) (26.0).669 (17.0) (48.0).905 (23.0) (15.2).984 (25.0) (29.4) (30.0).709 (18.0) (49.0) (26.0) (18.3) (28.0) (32.8) (33.0).709 (18.0) (49.0) (29.0) (20.0) (32.0) (35.4) (36.0).709 (18.0) (49.0) (33.0) (23.0) (34.0) (39.0) (40.0).709 (18.0) (53.0) (35.0) (26.0) 1.50 (38.0) (42.1) (43.0).709 (18.0) (53.0) (39.0) (28.8) (41.0) (45.2) (46.0).709 (18.0) (53.0) (42.0) n series only contact arrangements 83 and 833 available 54

18 26482 eries onnectors Jam ut eceptacle with rounding ontinuity (for shielded cable) T/ 7...Z hell ø ø ø T ize in ax. ax. 1.0 ax. ±0.25 ± (6.6).630 (16.0).716 (18.2).524 (13.3).590 (15.0) (47.0).905 (23.0).748 (19.0) (9.2).709 (18.0).842 (21.4).634 (16.1).590 (15.0) (47.0) (27.0).874 (22.2) (12.2).866 (22.0).968 (24.6).787 (20.0).669 (17.0) (49.0) (31.7) (27.0) (15.2).984 (25.0) (27.8).874 (22.2).709 (18.0) (50.0) (34.9) (30.2) (18.3) (28.0) (30.9) (26.2).709 (18.0) (50.0) 1.50 (38.1) (33.3) (20.0) (32.0) (34.1) (28.5).709 (18.0) (50.0) (41.3) (36.5) (23.0) (34.0) 1.50 (38.1) (32.5).709 (18.0) (55.0) (46.0) (39.7) (26.0) 1.50 (38.0) (41.3) (34.8).709 (18.0) (55.0) (49.2) (42.9) (28.8) (41.0) (44.4) (37.9).709 (18.0) (55.0) (52.3) (46.0) n series only contact arrangements 83 and 833 available T/...Z Wiring nstructions ixing of shielding braid to connectors with Zadapter oosen lock nut (5). lide heat shrink component (6) and lock nut (5) over cable. ush shielding braid (7) onto endbell (3) and over thread (2). asten shielding braid (7) into rounded groove by means of bailing wire old back protruding shielding braid on cone. lide lock nut (5) onto endbell (3). The folded back shielding braid protrudes under the tightened lock nut. hrink heat shrink component (6) according to manufacturer s instructions. (nd of heat shrink component to be located in square groove (1)). 55

19 26482 eries onnectors anel utouts ox and Wall ounting eceptacle ±.005 (013) 4 O (0.25).000 (0.00) Jam ut eceptacle (0.25).000 (0.00) (T..) (0.00).010 (0.25) (OT OUT) OUT O. T/ hell T/ ize ia. ±.005 crew (15.70).594 (15.09).125 (3.17) # (16.67).719 (18.26).125 (3.17) # (21.82).812 (20.62).125 (3.17) # (25.02).906 (23.01).125 (3.17) # (28.27).969 (24.61).125 (3.17) # (31.37) (26.97).125 (3.17) # (34.57) (29.36).125 (3.17) # (37.72) (31.75).125 (3.17) # (40.92) (34.92).155 (3.94) #6 ot available in connectors. hell T/ ize (14.68).540 (13.72) (17.86).665 (16.89) (22.61).828 (21.02) (25.78).952 (24.18) (28.96) (27.33) (32.13) (30.51) (35.31) (33.68) (38.48) (36.86) (41.66) (40.03) ot available in connectors. anel Thickness aximum panel thickness dimensions allowable to ensure complete connector operation for the the Wall ounting eceptacle, ox ounting eceptacle, and Thruulkhead eceptacle. Wall ounting and ox ounting eceptacle Thruulkhead eceptacle OT T T OT T T ize ax..087 (2.21).212 (5.38) ize ax. panel and screw head.218 (5.54).334 (8.74).311 (7.90) 56

20 26482 eries onnectors pecifications The following excerpts are some of the paremeter requirements of the specification. Test aragraph escription eference equirements ontact etention fter preloading to 3 pounds maximum, the force shall be applied at a rate of approximately 1 pound per second and maintained at full load for 510 seconds.. o damage to contacts or insert shall result nor shall the contacts be dislocated from their normal position in the connector more that inch under giveload for and within 1 minute after the load is removed for T. ontact ize oad in ounds in oad in in ontact nsertion/xtraction ( only) oupling Torque urability nsert etention nsulation esistance Vibration hock Thermal hock umidity ir eakage (T Only) alt pray (orrosion) luid mmersion When using the proper insertion and extraction tools the forces required to insert or extract the contact shall not exceed 20 bs. onnectors shall be less endbell. or qualification testing, mating halves shall be coupled and uncoupled, measuring the torques necessary. The torques required to couple and uncouple mating connectors halves shall fall within the limits specified as follows: Torque in lb () Torque in lb. () hell ize ax in. hell ize ax in 8 8 (.90) 1 (.11) (3.16) 4 (.45) (1.36) 1 (.11) (3.62) 6 (.68) (1.81) 2 (.23) (4.07) 7 (.79) (2.26) 4 (.45) (4.97) 7 (.79) (2.71) 4 (.45) onnector halves shall be mated and unmated 500 times at a rate of 200 ± 100 cycles per hour. The test may be performed by hand or by mechanical means, but the coupling ring shall be operated as in normal service. ailure to complete this test because of mechanical malfunction shall be cause for rejection. onnectors with the endbells and gromments (if possible) removed shall be subjected to a 75 psi load on the insulator in both directions. The load shall be applied at a rate of 10lb/sec. and held for 5 to 10 secs. nsulators shall not be dislodged from their original position. On unmated connectors at 25º ±3º a potential of 500 V ±10% shall be applied between all, but not more than 6, pairs of adjacent contacts and between all, but not more than 6, contacts and the shell. ailure to meet a minimum requirement of 5,000 megohms shall be cause for rejection. Wired, mated connectors shall be subjected to the vibration test of T1344, ethod 205, Test ondition. eceptacles shall be mounted on the vibration fixture by normal means. ll contacts shall be wired in a series circuit and 100 max. milliamperes of current shall be allowed to flow through the series circuit during vibration. uitable means shall be employed to monitor the current flow and to indicate any discontinuity of more than 10 microseconds. The wire bundle shall be clamped to nonvibrating points at least 8 inches from the rear of the connector. urrent discontinuity of 10 microsecond or more, disengagement of the mated connectors, evidence of cracking, breaking, or loosening of parts shall be cause for rejection. Wired, mated connectors shall be subject to one shock in each direction in each of three mutually perpendicular axes. The pulse shall be approximate half sine wave of 50g±15% magnitude with a duration of 11 ± 1 milliseconds. eceptacles shall be mounted on a shock fixture by normal means. ll contacts shall be wired in a series circuit and ma. of current shall flow through the series circuit during shock. uitable means shall be employed to monitor the current flow and to indicate any discontinuity of more than 10 microseconds. urrent discontinuity of 10 microseconds or more, disengagement of the mated connectors, evidence of cracking, breaking, or loosening of parts shall be cause for rejection. Wired, unmated plug and receptacle shall be subjected to 5 cycles of hot and cold temperatures. aximum temperature shall be +125º and the minimum shall be 55º. The temperature extreme shall be 1/2 hour minimum. racking, breaking or loosening of parts shall be cause for rejection. The connectors shall be subjected to varying humididity, 50% to 95%, conditions for a period of 10 days or 20 days T. The insulation resistance shall not be less than 100 megohms. 30 psi pressure differential shall be applied across the connector for 30 minutes. The leak rate, in either direction, shall be no greater than 1 atmosphere cubic inch per hour (4,55 X 10 3 cm 3 /) at 67º (55º). Unmated and wired connectors shall be subject to a salt fog for 48 hours. These shall be no exposure of base metal, the connector shall be functional and meet the contact resistance requirement. t least one connector, unmated and wired, shall he immersed in each fluid for a period of 20 hours then dried for an hour. onnectors shall be able to make and meet the coupling torque requirements. a) ydraulic luid per 5606, b) ubricating Oil per

21 26482 eries onnectors Tooling rimp 22520/101 TOO 22520/0102 Turret T520/530 Tooling nsertion/xtraction nsertion xtraction ontact ize ontact ize ontacts #20 ontact ilitary olor ands TT annon ize/type art umber 1st 2nd 3rd art umber 20 ocket 39029/32259 ed reen White in 39029/31240 ed Yellow lack ocket 39029/32247 ed Yellow Violet in 39029/31228 ed ed rey Wire ole illers/rommets ealing lugs ontact art umber olor ize annon ilitary ode ed lue 58

22 26482 eries onnectors ssembly nstructions Wire ontact ize trip ize W mm 2 nsulation mm 20 #20# / #16# / OTT 1. trip wires according to the table above taking care not to cut or nick strands. 2. nserts stripped wire into contact crimp pot. Wire must be visible thru inspection hole. 3. Using correct tool and locator select proper crimp setting for wire sizer to be crimped; cycle the tool once to be sure the indentors are open. nsert contact and wire into locator. queeze tool handles firmly and completely to insure a proper crimp. The tool will not release unless the crimp indentors in the tool head have been fully actuated. elease crimped contact and wire from tool. e certain the wire is visible thru inspection hole in contact. UTO: heck that none of the contacts are bent or damaged in any way after crimping. OTT TO 1. emove hardware from plug and receptacle. lide hardware overwire bundle in proper order for reassembly. 2. Use the proper contact insertion tool and slide the tool over the terminal end of the contact. The size 16 contact lies in the tool and the tool tip butts against the contact shoulder. The rear, or insulation support of the size 20 contact butts against an internal shoulder in the tool tip. OT: pply a small amount of isopropl alcohol to the insertion tool tip while installing contacts. 3. eginning from center cavity and working outwards in a circular pattern, insert wired contacts into rear of connector by hand untill the front of the contact shoulder is no more than 1/8 from the grommet. olding the connector horizontally, position tool behind contact. ush tool straight into contact cavity untill contact snaps into position. light pull on wire will assure that contact is locked securely. epeat for remaining contacts. ize Torque inlb () 8, 10, 12 and ( ) 16 and ( ) 20, 22 and ( ) 4. Use contacts and grommet sealing plugs to fill any empty cavities. OTO 4. heck face of plug or receptacle for proper contact installation. 2. Using mating connector with contacts installed, mate both connector halves together. 3. ssemble errule over the grommet by hand as far as possible. 4. ssemble endbell over ferrule and loosely tighten endbell. artially loosen (1/4 turn) and retighten to recommended torque limits. 2nd ndex ine ocket ontacts 1st ndex ine in ontacts OTT XTTO 1. lide hardware back over wire bundle. Using proper extraction tool or extraction end of proper insertion/extraction tool, proceed as follows: : There are two lines on the clip sleeve which are vital to the removal process. The first index line is used for removing pin contacts while the second index line is for removing socket contacts. arefully place the tool tip over the contact to be extracted until the tool tip touches the insulator face. arefully rotate the tool until the index line is slightly below the insulator face. eep an even pressure against the tool body; push plunger forward with thumb and index finger, and push the contact out through the clip. arefully remove extraction tool from connector. ull wire by hand to complete the removal of the contact. 59

23 26482 eries onnectors ow to Order pecial Termination onnectors T T T W W W W W W X TY (o lass required, less rear termination) Z OTT T OTT TY ocket TT T OTO ontact TT annon for additional nformation older Type T03/04/05 upplied less endball, ferrule and grommet. T03 T04 T05 rimp Type 03/04/05 upplied less endball, ferrule Twist ull anyard elease oupler lug T06/06 X TY V TY Z OTT T OTT TY OZTO OTO O* T W Z *Omit (0) of shell style indication when using this modification code. 16 = Overall length of connector including lanyard to be 6.0 (152.40) +_.125 (3.18) when measured over a 1.0 (25.40) +_.005 (0.13) diameter mandrel. 60

24 26482 eries onnectors ross eference ist T/26482, V art o. T art o. art o. TT annon V T00**** T00**** T00**** 3110**** T00**** 3110**** T00**** T00J**** 3110J**** T00**** 3110**** T0**** T0****Z T01**** T01**** T01**** 3111**** T01**** 3111**** T01**** T01J**** 3111J**** T01**** 3111**** T1**** T06**** T06**** T06**** 3116**** T06**** 3116**** T06**** T1****Z T06J**** 3116J**** T06**** 3116**** T6****88 T6**** T6****Z T02**** 3112**** ****V T07**** T07**** 3114**** T07**** 3114**** T08**** T08**** T08**** T7**** T**** 3119**** ross eference ist ist rotective aps art o. art o. art o. TT annon V T T Z 2...V T T Z 1...V T

25 26482 eries onnectors ross eference ist /26482, V art o. art o. art o. TT annon V **** 00**** 00**** 3120**** ****V **** 3120**** ****V ****Z ****V J**** 00**** 3120**** 0**** 00**** 01**** 25101****50 01**** 01**** 3121**** 01**** 3121**** 01**** 01J**** 01**** 3121**** **** 02**** 3122**** ****V **** 06**** 06**** 3126**** 06**** 3126**** ****V **** 06J**** 06**** 3126**** 6****88 6****88 ****V **** J****V ****Z ****V **** 1****Z 7**** ****V **** 3124**** ****V **** 3124**** ****V **** 08**** 08**** 7****Z T****V