Temperature measurement
|
|
- Mae Shaw
- 6 years ago
- Views:
Transcription
1 Temperature measurement 2
2 Example of connections of particular elements Temperature display units BGK85 Option Computer, control, itp. Temperature measurement TFC TFL Temperature regulator BGK81 BGK84 J, K, L, PT 100
3 Melt temperature measurement and control BAGSIK Sp. z o.o. Temperature sensors from our offer are designed to measure temperature of melt plastics including rubber, paste and liquids up to 400 C. The measurement may be carried out through different type configurations: Only PT100 sensor can be connected with a copper cable. Other J, K, L types should be linked with the same type cables. The sensor structure does not influence the flow itself and it does not degrade plastics which must be homogenised. It is recommended to use sensors with a cone to measure the temperature inside the canal, not next to the flange wall. The length of metering tip must be adjusted to the melt canal diameter. All other ways of use are inacceptable and resulted damages are not covered by guarantee. If we have only one hole available, the pressure transducer can be used with the temperature transducer. The transducer membrane must touch material, for this reason the melt temperature measurement is calculated next to the flange wall. Metal temperature caused by barrel or heater flange will have impact on this measurement. Temperature sensor and cable connections Transducer with a thermally insulated tip allows an accurate and honest measurement of molten material temperature. Thanks to the ceramic insulation, temperature does not affect the measurement. Temperature sensor design with ceramic insulation All temperature sensors are equipped with coned measurement tip permitting a correct and simple covering. These cable connections are also equipped with stable end with rotate-and-lock coupling. The length of metering tip may be selected within 0-25 mm. The standard version may be used to 400 o C. For high temperatures we offer special sensors for up to 500 o C. Izolacja Ceramic ceramiczna isolation Melt temperature sensors Galwanicznie galvanically odizolowany isolated czujnik temperatury sensor Length of metering tip Selection of metering tip length depends on the canal diameter and material viscosity. The length may vary between 0 and 25 mm in 5 mm long intervals. Ends are equipped with thermocouples Fe-CuNi of J, NiCr-Ni of K type or thermometric Pt100 resistors. 0 mm 5 mm 10 mm 15 mm 20 mm 25 mm For standard sensors, like for screens, we assure delivery of the ordered goods within 24 h from the moment of order placement.
4 Temperature sensor installation To make a hole to install the sensor, special tools and high skills are required. High tolerance and surface quality maintenance is difficult. For this reason, we suggest using reducer bushes. Warning! Temperature sensor disassembly Dimensions M18 x 1.5 mm Thread 1/2-20UNF-2A D1 M18 x 1.5 mm 1/2-20UNF-2A D2 Ø Ø D3 Ø Ø D4 Ø Ø a b c Before the transducer installation, the dimensions of the mounting thread should be controlled in regard to correct dimension maintenance and tolerance. Additionally, the hole should not contain any contamination or material remnants. We recommend using the plug before screwing in the sensor in order to check the thread and copper paste for easier sensor unscrewing during the disassembly. The transducer should be screwed in sealing surface (cone) without using a spanner. The moment of transducer installation for ½ -20UNF thread is 5 Nm, for M18x1,5 thread 10Nm. Sensor disassembly should be carried out in a heated state ( in the temperature of material melting).
5 Temperature sensors without an insulated metering tip series TFC / TFL TFC TFC line is intended for measuring temperature of all kind of molten polymer. These sensors are characterized by an exceptionally attractive price, reliability, versatility, compatibility and maximum quality. Cables and plugs located on the sensor head ensure a good connection quality. TFC sensors may be delivered with thermocouple Fe-CuNi of J, L types and NiCr-Ni of K type, as well as Pt 100-2, 3 and 4-wired. The installation is the same as for other sensors measuring liquid temperature. Technical data for TFC and TFL Sensor Output signal (integrated with the amplifier) Transfer of heat value Insulating sleeve Thermocouple or resistance sensor 0-10 VDC 4-20 ma (linear temp.) : 15W/m x k 2.5 W/m x k Material contacting the medium (optional) Isolation of the resistance in temperature sensors Max pressure of the molten medium at 20 o C, about 200 MOhm at 100 V, at 400 o C, about 2040 MOhm at 100 V 2000 bar Special features of temperature sensor: High quality and durability Golden plug connection High durability Attractive price Versatility, compatibility Suitable for temperature of up to 400 o C Melt temperature sensors TFL Special features of temperature sensor: TFL temperature sensor is a universal and at the same time practical sensor for temperature measurement thanks to the use of resistant thermocouple. It is a durable and resistant sensor for measuring temperature using a resistant thermocouple. It is a solid and resistant device, the figure of which is based on a one-piece shaft. The cable length between the sensor and the plug may vary according to customer s needs. The sensor may be equipped with a thermocouple Fe-CuNi of J, L types and NiCr-Ni of K type. The thermocouple Pt 100-2, 3 or 4-wired is also possible. Dimensions and threads are identical as in other types of liquid temperature transducers. High durability Universal compatible connection socket High quality and durability Suitable for temperature of up to 400 o C Different lengths of metering tips Perfect quality for the offered price
6 Temperature sensors without an insulated metering tip series TFC / TFL ( C ) ( B ) ( A ) 25 TFC SW ( D5 ) ( D4 ) ( D1 ) ( D3 ) D1 D2 D3 D4 D5 A B C SW M18 x /19 1/2-20UNF-2A ( L1 ) ( D2 ) ( C ) ( B ) ( A ) 11 TFL SW ( D1 ) ( D3 ) ( D2 ) D1 D2 D3 D4 D5 A B C SW M18 x /19 1/2-20UNF-2A ( L1 ) How to order Series TF Measurement tip Thread Thermocouple Measurement tip 0 = 0 mm 5 = cone 5 mm 10 = cone 10 mm 15 = cone 15 mm Thread 20 = cone 20 mm 1/2 = 1/2-20UNF-2A 18 = M18x1.5 Series C = standard 156 mm L = flexible 457 mm Thermocouple 1J = termocouple type J PT100 = thermocouple PT100 Example: TFC-1/2-5-1J Melt temperature sensor, standard 156 mm, thread 1/2-20UNF, cone tip 5 mm, integrated thermocouple type J. Example: TFL-1/2-10-1J Melt temperature sensor, flexible 457 mm, thread 1/2-20UNF, cone tip 10 mm, integrated thermocouple type J.
7 Fe-CuNi, NiCr-Ni / Pt 100, Pt 500, Pt 1000 Thermocouple Thermocouple, known also as thermo-element or thermo-cell, is one of the automation elements to measure temperature. It is characterized by high reliability, fineness and elasticity of structure which allows to apply it in different conditions. Available with 1 or 2 thermo-cells. Thanks to its springs, the depth of thermocouple immersion can be steplessly regulated by the rotation of the bayonet cap. Technical data Number of thermocouples 1, 2 Diameter Ø 4 Ø 6 Ø 8 Type of tip Type of thermocouple Internal diameter of fastener, dipstick cap flat 120 o angle Fe-CuNi type J Fe-CuNi type L NiCr-Ni type K Pt 100/500/ mm Bushing thread Ø 12,2 Ø 14,5 SW1, length of 30mm M10 x 1 M12 x 1 M14 x 1.5 G 1/4 G 3/8 M12 x 1.75 G 1/2 Special features of thermocouples: No external power supply required Small dimensions Low thermal volume Low inertia time Wide range of measurements with good linearity Simple structure high reliability Melt temperature sensors
8 Fe-CuNi, NiCr-Ni / Pt 100, Pt 500, Pt 1000 Thermocouple Cable length Spring length Thermocouple T U J L E K N R, S B Material + Cu Cu Fe Fe NiCr NiCr NiCrSi Pt10Rh Pt30Rh - CuNi CuNi CuNi CuNi CuNi Ni NiSi Pt Pt6Rh Color Warning To connect and extend cables, the cable of the same type as the one of transducer is needed (except for Pt100 regular copper Cu cable)!!! How to order Series Type Tip Thread Cable Thermocouple Bayonet thread 10 = M10x1 12 = M12 14 = M14x1.5 Cable length 3 = 3 meter 5 = 5 meter 10 = 10 meter Diameter of tip 4 = Ø4 6 = Ø6 8 = Ø8 Thermocouple type J = thermocouple type J - 400ºC L = thermocouple type L - 410ºC PT100-3 = Thermocouple type PT100-3 wire PT100-4 = Thermocouple type PT100-4 wire Example: Thermocouple J Thermocouple, type J, diameter of tip Ø6, bayonet thread M14x1.5, cable length 5 meter.
9 Accessories Reducer bushing Reducer Bushing make it easy to make a hole for mounting the temperature and pressure sensors. The bushing is made of hardened and nitrided steel. To mount reducing bushing it is enough to use a regular M16, M18 or M24 tap metric. Reducer bushing types: M16 1/2-20 UNF - 2A M18x1,5 1/2-20 UNF - 2A M24 M18x1,5 flange sensor bushing Screwdrivers for reducer bushings Special screwdriver was designed to screw in and unscrew reducer bushings. It is required to avoid damaging the reducer bushing during tightening it with maximum torque. Reduction bushing socket cleaning tool Any contamination of sensor mounting thread can cause its destruction. To avoid this the socket and reduction bushing mounting thread should be cleande before every sensor replacement. This will extend the life of the sensor and reduction bushing. Accessories Plug tools All unused holes for pressure and temperature sensors should be closed with special closing plugs with suitable thread, assuring 100% hole tightness. Dimensions: 1/2-20 UNF - 2A M18 x 1,5 mm M24
10 Accessories Interconnect cables Standard cables have one plug at one end to connect with transducer. All standard interconnect cables are 3, 5,7.5 and 10 m long. Special sets of measuring cables may be delivered on special request (e.g. resistant to high temperature). Plugs Converters and temperature and pressure transducers are connected with high quality resistant and reliable plugs. All plugs have golden pins and they are compatible with EMC and assure the security in compliance with technological standards. SSR-Solid State Relay SSR type: 10 A / 25 A / 40 A / 60 A / 75 A Bayonet Threaded sleeve with a thermocouple holder, available in the following dimensions: M10x1 M12x1 M14x1.5 Bag Fast Clean High quality paste for cleaning metal elements from plastics and contamination. How to use: with our paste, metal elements may be cleaned from stuck or burnt plastics in two ways: Hot - put the paste on a preheated element (steel), place it equally on the whole surface and then using a brass brush located e.g. in the drill clean the given element Cold - the surface intended to be clean spray with oil and then using a brass brush scrape filings off the paste onto the element that is being cleaned. Using a brass brush located e.g. in the drill clean well the given element.
11 Poland Toruńska 8 PL Gliwice office@bagsik.net Phone: Mob: Germany Obere Heide 5 D Üchtelhausen office@bagsik.net Phone: kom: Russia RU Kazan Vosstanija str gulnaz.iamilova@mail.ru Phone: kom: Ukraine UA Wyshgorod, Kievskaia oblast office@bagsik.net Phone: kom:
INTERNATIONAL METAL ENGINEERING
INDICATING TEMPERATURE TRANSMITTER WITH HART 8080HT UNIVERSAL SETTINGS WITH HART PROTOCOL FOR VARIOUS INPUT SIGNALS 2 WIRE TECHNOLOGY, 4 TO 20mA ANALOG OUTPUT HIGH ACCURACY IN TOTAL AMBIENT TEMPERATURE
More informationElectronic Monitoring Systems
JJ Electronic digital thermometer JJ Multi-channel temperature indicator JJ Temperature sensors JJ KombiTemp Electronic Monitoring Systems and Temperature Sensors DS_Electronic_monitoring_systems_and_temperature_sensors
More informationElectronic Monitoring Systems
JJ Electronic digital thermometer JJ Multi-channel temperature indicator JJ Temperature sensors JJ KombiTemp Electronic Monitoring Systems and Temperature Sensors DS_Electronic_monitoring_systems_and_temperature_sensors
More informationMetal-Protected Measuring Inserts
Product Information 176 Metal-Protected Measuring Inserts Thermocouples and Resistance Thermometers DIN 43 735 The following table shows in comparison the different types of measuring inserts. They are
More informationELECTRONIC MONITORING SYSTEMS AND TEMPERATURE SENSORS
JJ Electronic digital thermometer JJ Temperature sensors JJ KombiTemp JJ CargoTemp roller JJ Display and monitoring systems ELECTRONIC MONITORING SYSTEMS AND TEMPERATURE SENSORS DS_Electronic_monitoring_systems_and_temperature_sensors
More informationTemperature sensor type T.3., Construction type 3, plug-in sensor for protection tube with lateral cable outlet (Pt100/Pt1000, NTC)
Temperature sensor type T.3., Construction type 3, plug-in sensor for protection tube with lateral cable outlet (Pt100/Pt1000, NTC) Measuring principle Temperature range Protection class Mounting Material
More informationOperating Instructions TF04
10 Brent Drive Hudson, MA 01749 Tel: +1-978-212-0006 Fax: +1-978-568-0060 Borsigstrasse 24 D-65205 Wiesbaden-Nordenstadt Tel: 06122 / 7055-0 Fax: 06122 / 7055 50 Operating Instructions TF04 Temperature
More informationThermocouples TE Measuring Insert. rigid Model TC 001 flexible Model TC 002. Electronic Temperature Measurement
TE 65.01 Thermocouples Measuring Insert Electronic Temperature Measurement rigid Model TC 001 flexible Model TC 002 Services intended Exchangeable measuring insert for all industrial and laboratory applications.
More informationJUMO thermocor. Portable measuring system for AMS2750 and CQI-9. Brief description. Block diagram. Special features. JUMO thermocor.
Page 1/8 JUMO thermocor Portable measuring system for AMS2750 and CQI-9 Brief description The JUMO thermocor is a high-precision documenting test device with 12 analog inputs for thermocouples. The use
More informationhotrod Cartridge Heaters
hotrod Cartridge Heaters hotrod Cartridge Heaters Components We provide our customers with an extensive portfolio of ments, thermal sensors and control technology. Since 1973, we have manufactured heating
More informationC T EM P ERATU R E S ENS OR. we get to the point... Gräff GmbH Bonner Strasse 54 D Troisdorf Tel: +49(0) Fax: +49(0)
TEMPERATURE SENSORS C T EM P ERATU R E S ENS OR we get to the point... Gräff GmbH Bonner Strasse 54 D - 53842 Troisdorf Tel: +49(0)2241-4907-0 Fax: +49(0)2241-4907-77 INTERESTING FACTS Gräff GmbH Competence
More informationKombiTemp. Head form B / Head form J Cable socket, angle type Diesel engine dial thermometers. Temperature Sensors with local display
JJ Head form B / Head form J JJ Cable socket, angle type JJ Diesel engine dial thermometers KombiTemp Temperature Sensors with local display Including products with: DS_KombiTemp 8/5 Dual temperature control
More informationArticle on Sheath materials, Thermowells, Fittings, and Terminations
Article on Sheath materials, Thermowells, Fittings, and Terminations 1. INTRODUCTION Temperature sensor element for laboratory and industrial use should normally be protected by some form of sheath or
More informationJUMO safetym TB/TW Temperature limiter, temperature monitor according DIN EN
JUMO GmbH & Co. KG Delivery address:mackenrodtstraße 14, 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: +49 661 6003-0 Fax: +49 661 6003-607 e-mail: mail@jumo.net Internet: www.jumo.net
More informationTemperature Sensors. Accessories. for Injection Molding. Types 6192B, 6193B,
Accessories Temperature Sensors for Injection Molding Types 6192B, 6193B, 6194B, 6195B Temperature sensors for measuring the contact temperature directly in the cavity at the surface of the solidified
More informationHead form B Head form J Cable socket, angle type KOMBITEMP TEMPERATURE SENSOR WITH LOCAL DISPLAY. Including products with:
JJ Head form B JJ Head form J JJ Cable socket, angle type KOMBITEMP TEMPERATURE SENSOR WITH LOCAL DISPLAY Including products with: DS_KombiTemp 5/ Dual temperature control with only one measuring point!
More informationJUMO thermocor. Portable measuring system for AMS2750 and CQI-9. Brief description. Block diagram. Special features. JUMO thermocor.
sales@jumo.co.uk info.us@jumo.net Page 1/8 JUMO thermocor Portable measuring system for AMS2750 and CQI-9 Brief description The JUMO thermocor is a high-precision documenting test device with 12 analog
More informationMELT PRESSURE TRANSMITTERS K7 SERIES PERFORMANCE LEVEL c
MELT PRESSURE TRANSMITTERS K7 SERIES PERFORMANCE LEVEL c Voltage output The K7 Performance Level c series of Gefran are pressure transmitters for using in high temperature environment. The main characteristic
More informationMELT PRESSURE TRANSMITTERS K7 SERIES PERFORMANCE LEVEL c
MELT PRESSURE TRANSMITTERS K7 SERIES PERFORMANCE LEVEL c Voltage output The K7 Performance Level c series of Gefran are pressure transmitters for using in high temperature environment. The main characteristic
More informationCable thermocouple Model TC40
Electrical temperature measurement Cable thermocouple Model TC40 WIKA data sheet TE 65.40 for further approvals see page 11 Applications For direct installation into the process Machine building Motors
More informationProcess controller. for pneumatic and electric actuators. Process controller V. Process controller
for pneumatic and electric actuators Process controller 110-240V Process controller dtron 316 in Rittal-cabinet with current loop sensor input for controlling pneumatic and electric actuators with a position
More informationAnalog input module. Brief description. Page 1/8. Data Sheet
JUMO GmbH & Co. KG Delivery address:mackenrodtstraße 14, 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: +49 661 6003-0 Fax: +49 661 6003-607 e-mail: mail@jumo.net Internet: www.jumo.net
More informationhotrod Cartridge Heaters Application Fields
For heating applications: - Packaging machines - Extruders - Casting machines - Hot melt - Cutting knives - Analytical equipment in laboratories Custom options: - Power distribution - Numerous attachments
More informationPULL HANDLES THERMOPLASTIC CAST IRON ALUMINUM STAINLESS STEEL BIG HAND STYLE P U L L H A N D L E S
473 THERMOPLASTIC CAST IRON P U L L H A N D L E S ALUMINUM PULL HANDLES Manual Clamps 9 TriMax Vises 81 Pneumatic Workholding 121 Supports, Stops & Set Up Accessories 137 Precision Tooling Plates, Blocks
More informationVoltage Output MELT PRESSURE TRANSMITTERS IN SERIES TECHNICAL SPECIFICATIONS
MELT PRESSURE TRANSMITTERS IN SERIES Voltage Output The IMPACT series of Gefran, are pressure transmitters, without transmission fluid, for using in High temperature environment (350 C). Medium pressure
More informationCable thermocouple Model TC40
Electrical temperature measurement Cable thermocouple Model TC40 WIKA data sheet TE 65.40 Applications For direct installation into the process Machine building Motors Bearings Pipelines and vessels Special
More informationCylinder Pressure Sensor
Pressure Cylinder Pressure Sensor 6613CG... for On-Line Combustion Control Piezoelectric pressure with galvanic isolated 4 20 ma output signal for continuous cylinder pressure measurement for medium and
More informationSafety technology/equipment
Safety technology/equipment Reliable electronic and electro-mechanical products according to DIN EN 14597 Contact Phone: +49 661 6003-727 Email: automation@jumo.net Dear Readers, Safety and reliability
More informationScrew-in melt thermocouples
JUMO Instrument Co. td. Data sheet 901090 Page 1/5 k Temperature range from -40... +600 C k Available with different thermocouples k Stainless steel thermowell and probe tip k Structure insulated or connected
More informationTemperature Sensors. Accessories XST. for Injection Molding. Type 6192A..., 6193A..., 6194A...
Accessories XST Temperature Sensors for Injection Molding Type 6192A..., 6193A..., 6194A... Temperature sensors for recording the contact temperature directly in the cavity at the surface of the solidified
More informationThis is trial version
Z-Standards Contents (Alphabetical order, terms partly according to DIN 16750) A All dimensions shown in this catalogue are specified in mm, given tolerances refer to an ambient temperature of 20 C Prod.-No.
More informationFor the plastics machinery industry Fixed bayonet thermocouple Model TC47-FB
Electrical temperature measurement For the plastics machinery industry Fixed bayonet Model TC47-FB WIKA data sheet TE 67.24 Applications Plastics and rubber industry For direct installation into the process
More informationSeries 09SVP Single Axis Valve Gate Nozzle
Series 09SVP Single Axis Valve Gate Nozzle Stabilize your Process CAT-01-0065_EN-Rev03 EN 01 / 2018 Product Description - Technical Data NOTICE Valve Pin Operation Operation medium Pressure range Flowrate
More informationModules for fine machining. Guhring modules 6x6 and 4x4. NEW: Module 6x6
NEW: Module 6x6 simple, quick and highly accurate setting of 6-fluted tools minimal tension thanks to 6 setting elements perfect balancing with 6 balancing screws Modules for fine machining Guhring modules
More informationINSTALLATION AND MAINTENANCE OF TOP LOADING ARM
INSTALLATION AND MAINTENANCE OF TOP LOADING ARM D TABLE OF CONTENTS 1. INTRODUCTION 04 2. SPECIFICATION OF THE REDLANDS LOADING ARM 04 3. INSTALLING THE LOADING ARM 3.1. Installation Procedures 05 4.
More informationDME HYDRAULIC LOCKING CORE PULL CYLINDERS Specification No. ME-E (A) Part No. HLCP-PS02 Page 1 of 13
Specification No. ME-E32-0002(A) Part No. HLCP-PS02 Page 1 of 13 IMPORTANT SAFETY INFORMATION 1. To avoid injury, exercise caution by reading these instructions before servicing or operating the system.
More informationThermocouples W A T L O W
W A T L O W Over 90 years of manufacturing, research and design makes Watlow a world class supplier of temperature measurement products. We have designed and manufactured millions of thermocouples for
More informationE a s y B - S e r i e s M o d u l e s M o u n t i n g I n s t r u c t i o n s f o r E a s y P I M a n d E a s y P A C K M o d u l e s
E a s y B - S e r i e s M o d u l e s M o u n t i n g I n s t r u c t i o n s f o r E a s y P I M a n d E a s y P A C K M o d u l e s IFAG IPC Edition 2011-02-02 Published by Technologies AG 59568 Warstein,
More informationINOX PrOgram made by eisele
EISELE INOXline Program Stainless steel connection solutions Quality solutions Made by EISELE INOX 2 Quality solutions - Made by EISELE EISELE IS QUALITY MADE IN GERMANY Over 30 patents, more than 5.000
More informationAir vane motors for special applications
Screwdriving technology Automation Air motors Air tools Air vane motors for special applications drilling motors 80-600 W milling motor 400 W grinding motors 150-1000 W robust and precise bearing high
More informationConveyors 12. slide strips roller Conveyors roller elements Conveyor rollers Chain Transfer
Conveyors slide strips roller Conveyors roller elements Conveyor rollers Chain Transfer Application example conveyors Transport solutions and goods provision 1 2 3 4 5 6 7 8 362 9 1 slide strips Low-wear
More informationShort Form Catalogue AJ Thermosensors
Thermocouples Short Form Catalogue AJ Thermosensors Resistance thermometers Head mounted Probe style Application specific Accessories See the individual datasheets for more detailed information on each
More informationVane pump upgrade kit 180F4161 isave 21 ERD Disassembling and assembling
Service guide Vane pump upgrade kit 180F4161 isave 21 ERD Disassembling and assembling hpp.danfoss.com Table of Contents Contents 1. General Introduction...2 1.1 Parts included in the vane pump upgrade
More informationRegloplas- Temperiertechnik. Temperature Control Technology. bringt Qualität in short, und Rentabilität auf. in quality and profitability!
MASTER OF TEMPERATURE CONTROL Regloplas- Temperiertechnik Temperature Control Technology bringt Qualität in short, und Rentabilität auf a decisive den increase Punkt! in quality and profitability! Regloplas
More informationALWAYS follow all Webasto installation and repair instructions and observe all warning instructions.
Water heater unit Feel drive Thermo Top E Auxiliary Heating Thermo Top C Auxiliary Heating Thermo Top P Auxiliary Heating e 00 000 e 00 000 e 00 004 Installation instructions Toyota RAV 4 Petrol From model
More informationTemperature sensors. and accessories for heat and cooling measurement points. Applications. Benefits. Features
Temperature sensors and accessories for heat and cooling measurement points Applications Temperature sensors are metrological components for heat or cold measuring points. They are used in pairs and measure
More informationFor the plastics machinery industry Adjustable bayonet thermocouple Model TC47-AB
Electrical temperature measurement For the plastics machinery industry Adjustable bayonet Model TC47-AB WIKA data sheet TE 67.20 Applications Plastics and rubber industry For direct installation into the
More informationHot Runner Thermocouples Model TC46
Electrical Temperature Measurement Hot Runner Thermocouples Model TC46 WIKA Data Sheet TE 65.46 Applications Plastics and rubber industry Hot Runner bushings, drops and nozzles Hot Runner manifolds Moulds
More informationContact dial thermometer
Data Sheet 608523 Page 1/8 Contact dial thermometer Special features Temperature controller with process value display as panel-mounting or add-on device Class 1.5 Protection rating IP 65 Case sizes :
More informationRepairing the CIS Jetronic Alloy adjustable Bosch Fuel distributor
CIS-Jetronic.com 07.3-0997-06-01 Repairing the CIS Jetronic Alloy adjustable Bosch Fuel distributor When do you have to repair your CIS Bosch fuel distributor? If your car has rough idle, low power, high
More informationMANUAL FOR. SHAFT GROUNDING ASSEMBLY WITH mv-meter AND AMPLIFIER FOR ALARM OUTPUTS
MANUAL FOR SHAFT GROUNDING ASSEMBLY WITH mv-meter AND AMPLIFIER FOR ALARM OUTPUTS BAC ORDER NO: 539630 Copyright: BAC CORROSION CONTROL A/S Færøvej 7-9 DK-4681 Herfølge Denmark telephone +45 7026 8900
More information4357 / 4860 MX Multi Adjuster
12_234 Frontfork 4357 / 4860 MX Multi Adjuster Introduction 2 Exploded view 3 Disassembly forkleg 4 Disassembly screw-cap 15 Assembling screw-cap 17 Disassembly cartridge 18 Disassembly compression holder
More informationCable Glands & Accessories
Cable Glands & Accessories This catalog features ITC s extensive range of liquid-tight, strain relief cord connectors (cable glands) and accessories, including locknuts, sealing washers, plugs, etc. These
More information2014 /2015. Product Overview. Instrumentation and Control. Temperature Measurement and Monitoring
Instrumentation and Control TEMPERATURE Product Overview 2014 /2015 Temperature Measurement and Monitoring Temperature Measurement and Monitoring PT-00 TD-01 PT-01 Surface Resistance Thermometer Compact
More informatione ALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Unit Thermo Top P Additional Heater e 00 004 Installation Instructions Toyota Land Cruiser J0 Diesel 4 5 6 from Model Year 005 For left-hand drive vehicles only Manual air conditioning not
More informationALWAYS follow all Webasto installation and repair instructions and observe all warning instructions.
Water Heater unit Feel drive Supplementary heating Thermo Top C e 00 000 Installation instructions Dodge Caliber Diesel From model year 007 For left-hand drive vehicles only WARNING! Hazard warning: Incorrect
More informationTN1250 Technical note
Technical note Press-fit ACEPACK power modules mounting instructions Introduction ST introduces the ACEPACK Power Module family, designed for easy mounting and reliable performance in rugged applications.
More information1.1 VTS: Manufacturer No. 1 in the world constituents of success
Air curtain 01 VTS GROUP 1.1 VTS: Manufacturer No. 1 in the world 1.2 3 constituents of success 02 WING 2.1 WING air curtains 2.2 Silence and power 2.3 Design and performance 2.4 Quality and design 2.5
More informationRectangular profiles RE 40
8.3 luminium profiles Rectangular profiles Features Universal precision, clamping and machining surface s a stabiliser for machine and subframe constructions luminium, ly anodised Produced in accordance
More informationThermocouples. General Applications Tube and Wire. Thermal Devices, Inc. Mount Airy, Maryland USA
Watlow is a world class supplier of temperature measurement products, with more than 90 years of manufacturing, research and design expertise. Companies engaged in critical process control of food and
More informationAutomatic Drilling and Tapping Units
Automatic Drilling and Tapping Units Contents Page Automatic drilling and tapping units... 25 Dimension sketches... 23 Introduction More mechanization in your drilling operations Simple and cost effective,
More informationThermocouples. General Applications Tube and Wire. Performance Capabilities. Features and Benefits. Typical Applications. Construction and Tolerances
Watlow is a world class supplier of temperature measurement products, with more than 90 years of manufacturing, research and design expertise. Companies engaged in critical process control of food and
More informationLevel indicators, screw plugs
Level indicators, screw plugs 885 Product overview Level indicators, screw plugs Oil level gauges K0443 Plastic plugs K0452 Oil level gauges K0444 Page 888 Aluminium plugs K0453 Page 894 Oil level sight
More informationG221 25/30 A Left/Right
Spare parts list (014/08) db 1 3 Spare parts list casing G1 A 1 4 Remarks G1 30 A Right PG G1 30 A Left Ordering no. G1 5 A Right Description G1 5 A Left Pos 1 Side panel right 5-4 blue left 8 738 17
More informationExhaust gas temperature sensors MBT 5113 and MBT 5116
Data sheet Exhaust gas temperature sensors MBT 5113 and MBT 5116 Heavy-duty sensors used for measuring exhaust gas from diesel engines, turbines and compressors within stationary and marine applications.
More informationECT Applications. Features
Industrial Pressure Transmitter Swiss based Trafag is a leading international supplier of high quality sensors and monitoring instruments for measurement of pressure and temperature. The economical pressure
More informationMounting and Operating Instructions EB 8135/8136 EN. Series V2001 Valves Type 3535 Three-way Valve for Heat Transfer Oil
Series V2001 Valves Type 3535 Three-way Valve for Heat Transfer Oil Type 3535 Three-way Valve with bellows seal and rod-type yoke (partial view) Mounting and Operating Instructions EB 8135/8136 EN Edition
More informationWater heater unit. Installation instructions. Peugeot Partner. Citroen Berlingo. Supplementary heating Thermo Top C. Table of Contents.
Water heater unit Feel the drive Supplementary heating Thermo Top C e1 00 0002 Installation instructions Peugeot Partner Citroen Berlingo 6 4 1 2 3 5 Gasoline and diesel From model year 2003 Only for left-hand
More informationTemperature sensors and transmitters
JJ For machinery and plant engineering JJ For marine applications and shipbuilding JJ For HVAC applications JJ Temperature Transmitters Temperature sensors and transmitters DS_Temperature_sensors_and_transmitters
More informationRTD and Thermocouple Assemblies Reference Manual
RTD and Thermocouple Assemblies Reference Manual www.rosemount.com RTD and Thermocouple Mounting and Installation Advice for Resistance Thermometers and Thermocouple Assemblies NOTICE Read this manual
More informationHotset High-Watt Density Cartridge Heaters
Cartridge Heaters hotset High-Watt Density Cartridge Heaters Hotset High-Watt Density Cartridge Heaters proven technology founded on our long term experience with many outstanding advantages. For applications
More informationIndustrial flue gas probes. Instruction manual
Industrial flue gas probes Instruction manual 2 1 Contents 1 Contents 1 Contents... 3 2 Safety and the environment... 4 2.1. About this document... 4 2.2. Ensure safety... 4 2.3. Protecting the environment...
More informationSafety switches for hinges
Safety switches for hinges Selection diagram ACTUATORS L L6 L9 L16 FR FM FX FZ FK CONTACT BLOCKS 6 7 9 14 18 snap action 1NO+1N, make before break, shifted, close 21 4 66 NC 2NO+ 1NO+ CONDUIT ENTRIES Threaded
More informationMessing. screw-in connectors
Messing screw-in connectors 2 Quality solutions - Made by EISELE EISELE IS QUALITY MADE IN GERMANY Over 30 patents, more than 8,000 standard articles, and 2,000 customized solutions impressively underline
More informationSEMITOP2,3,4 Press-Fit
Mounting Instruction SEMITOP2,3,4 Press-Fit Revision: 03 Issue date: 2017-08-28 Prepared by: Roberto Agostini Approved by: Werner Obermaier Keyword: SEMITOP, mounting instructions, one screw mounting,
More informationTemperature sensors. Fluidcontrol
Temperature sensors Changes in the viscosity of hydraulic oil and lubricants due to the temperature requires precisely monitoring and stabilising the operating temperature. Carefully monitoring the temperature
More informationDigital ph transmitter
Digital ph transmitter Compact, remote versions for DN 15 to 200 Fully programmable ph transmitter functions for all kinds of ph-measurement tasks Large range of process connections with various fittings
More informationInstruction Manual Extruder Sensor Rheomex 252/254
Instruction Manual Extruder Sensor Rheomex 252/254 Part No. 002-8632 3-1-014-2 08.1992 Thermo Haake Thermo Haake (USA) Rheo s.a. (France) Dieselstraße 4 53 W. Century Road 99 Route de Versailles D-76227
More informationIEC60309 PLUGS AND SOCKETS
High performance for each condition and every environment The industrial plugs and sockets are designed to withstand highly specific operating conditions that widely vary depending in which place and situation
More informationDigital ph transmitter
Digital ph transmitter Compact, remote versions for DN 15 to 200 Fully programmable ph transmitter functions for all kinds of ph-measurement tasks Large range of process connections with various fittings
More informationPRESSURE TRANSDUCERS. Specifications. Individual Specifications
00 Series and 00 Heavy Duty Series Compact OEM Pressure Transmitters 0 50 psi to 0-0,000 psi ranges (0-.5 bar to 0-,00 bar) High Proof Pressures Broad Choice of Outputs RoHS Compliant For OEMs that need
More informationSPLIT MOUNTED HT750/H1000/NT600 INSTALLATION MANUAL
9/26/16 HIGH TEMP BEARINGS SPLIT MOUNTED HT750/H1000/NT600 INSTALLATION MANUAL www.hightempbearings.com HTB Split Mounted HT750/1000/NT600 Sleeve Bearings Installation HTB Manual REV A REV A Split Mounted
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Unit Feel the drive Thermo Top E Additional Heater Thermo Top C Additional Heater Thermo Top P Additional Heater e 00 0003 e 00 000 e 00 004 Installation Instructions Mitsubishi Pajero Diesel
More informationTemperature Measurement Resistance thermometers
Temperature transmitters for mounting in the connection head The following temperature transmitters are available for mounting in the connection head: SITRANS TH100 Programmable two-wire temperature transmitter
More informationKTR Torque Limiters Overload Protection Systems
KT Torque Limiters Overload Protection Systems UFLEX - Friction Disk - Zero Backlash Ball Detent KT SI - Ball/oller Bearing Style KT SI Compact - Zero Backlash Ball Detent Catalog Contents (Metric) Page
More informationOwner smanual. Banks Monster-Ram Intake and Grid Heater Delete Kit. For Racing Only Ram 6.7L Pickup Trucks. with Installation Instructions
with Installation Instructions Owner smanual Banks Monster-Ram Intake and Grid Heater Delete Kit For Racing Only 2007-2017 Ram 6.7L Pickup Trucks THIS MANUAL IS FOR USE WITH SYSTEM 42788, 42788-PC, 42790,
More informationMOBILE MEASUREMENT TECHNOLOGY
WWW.CSM.DE WWW.SAB-WORLDWIDE.COM MOBILE MEASUREMENT TECHNOLOGY FOR HV COMPONENTS Also for AD and Pt measurement modules! CONTENT The companies S BRÖCKSKES GmbH & Co. KG und CSM GmbH - Computer-Systeme-Messtechnik........
More informationCATALOGUE. Metzerplas
CATALOGUE Metzerplas C E R T I F I C A T I O N 3 SP pipe is approved by standards institutes around the world Institute Certificate No. Product Standard Country IAPMO 4755 Pex-Al-Pex Composite pressure
More informationTHERMASGARD TF 43 THERMASGARD TF 65
THERMASGARD TF 65 Patented quality product (Immersion sensor patent no. DE 10 2012 017 500.0) THERMASGARD TF 43 is a resistance thermometer with a passive output, enclosure made from impact-resistant plastic
More informationHot runner thermocouple Model TC46
Electrical temperature measurement Hot runner thermocouple Model TC46 WIKA data sheet TE 65.46 for further approvals see page 7 Applications Plastics and rubber industry Hot runner bushings, drops and
More informationExternal gear pump Series G
External gear pump Series G RE 10 093/04.14 Replace RE 10 093/06.13 AZPG-22 Fixed pumps V = 22.5...100 cm 3 / rev Overview of contents Contents Page General 2 Product overview 3 Ordering code single pumps
More informationExternal Gear Pumps Series F
External Gear Pumps Series F RA 10089/08.11 Replaces: RA 10097 1/60 AZPF-... Fixed pumps Size 4.0...28 cm 3 /rev (.25-1.71 in 3 /rev) Overview of contents Contents Page General 2 Product overview 3 single
More informationSCM CLOCK MOVEMENT 03 USER MANUAL
SCM CLOCK MOVEMENT 03 USER MANUAL Issue 1.0 22.07.2016 draw 2 TABLE OF CONTENT 1. INTRODUCTION... 4 2. CLOCK MOVEMENTS VERSIONS... 6 3. INSTALLATION... 7 4. TURNING ON AND TURNING OFF... 9 5. SERVICE...
More informationSP A, SP. Submersible pumps Submersible motors Accessories. 50 Hz
SP A, SP Submersible motors Accessories For raw water supply, irrigation systems, groundwater lowering, pressure boosting and various industrial applications. 5 Hz TM 7318 2298 Contents General data Performance
More informationLOCKING BUSHES & SHAFT COLLARS
LOCKING BUSHES & SHAFT COLLARS INDEX TAPER BUSHES Page 3 WELD-ON HUBS Page 4 QD BUSHES Page 5 MECHANICAL LOCKING BUSHES CAL1 (Not Self-Centering) Page 6 CAL2 (Not Self-Centering) Page 7 CAL3 (Self-Centering)
More informationTechnical Data and Operating Instructions Thermal Dry Running Protection ATLS-T1
Technical Data and Operating Instructions Thermal Dry Running Protection ATLS-T1 Operational data for thermal dry running protection according to order data sheet Order No.: Ident No. ATLS-T1: Machine
More informationPOWER PRICE UNI. powerful UNF METAL. UNCPower. power ful GOLD FOR. powerful TOP GEOMETRIES UNF PERFECT CHOICE VER. perfect thread form.
MADE BY UNIVERSALtaps TOP GEOMETRIES FORM EUNIVERSAL UNIVERSAL TAPS powerful perfect UNF longideal flutes choice tool life PROCESS RELIABLE PERFECT universal power ful UNC-THREAD ISO-METRIC THREADS GUHRING
More informationScrew-in Thermocouples
TT30..39 s Application Thermocouples are suited for direct temperature measurement of gaseous and liquid media. The applications of the measuring inserts are not limited to the specified thermocouples.
More informationWater Heater Unit. Thermo Top C Additional Heater. Installation Instructions. FORD Connect. Gasoline and Diesel. not with automatic transmission
Water Heater Unit Thermo Top C Additional Heater e 00 000 Installation Instructions FORD Connect Gasoline and Diesel 4 5 6 not with automatic transmission only applies to left-hand drive vehicles See Page
More informationGRUNDFOS DATA BOOKLET SP A, SP. Submersible pumps, motors and accessories 50 Hz
GRUNDFOS DATA BOOKLET SP A, SP, motors and accessories 5 Hz Contents General data Performance range Page 3 Applications Page 4 Type key Page 4 Pumped liquids Page 4 Operating conditions Page 4 Curve conditions
More information