Call for product recommendations and to place your order!
|
|
- Imogen Clarke
- 6 years ago
- Views:
Transcription
1 Driveline: Note: Driveshafts come with pinion yoke with 2.5 square bolt pattern. If using Mustang Cobra center section with 3.0 square pattern, call us Denny s Driveshaft, MkI and MkII Roadster, All New, High Speed Balanced, HD 1330 Series U-Joints w/o grease fitting, 28 Spline for T-5 and Tremec Includes Ford 8.8 Flange Yoke. Made in USA Denny s Driveshaft, MkI and MkII Roadster, All New, High Speed Balanced, HD 1330 Series U-Joints w/o grease fitting, 31 Spline Yoke for Tremec TKO 500 & 600. Includes Ford 8.8 Flange Yoke. Made in USA Denny s Driveshaft, Coupe/Spyder GT, All New, High Speed Balanced, HD 1330 Series U-Joints w/o grease fitting, 28 Spline for T-5 and Tremec Includes Ford 8.8 Flange Yoke. Made in USA Denny s Driveshaft, Coupe/Spyder GT, All New, High Speed Balanced, HD 1330 Series U-Joints w/o grease fitting, 31 Spline Yoke for Tremec TKO 500 & 600. Includes Ford 8.8 Flange Yoke. Made in USA Denny s Driveshaft, MkIII Roadster, All New, High Speed Balanced, HD 1330 Series U-Joints w/o grease fitting, 28 Spline for T-5 and Tremec Includes Ford 8.8 Flange Yoke. Made in USA. Note: In special case of using bellhousing, order Denny s Driveshaft, MkIII Roadster, All New, High Speed Balanced, HD 1330 Series U-Joints w/o grease fitting, 31 Spline Yoke for Tremec TKO 500 & 600. Includes Ford 8.8 Flange Yoke. Made in USA. printed 09/24/09, Page 1 of 10
2 70607 Denny s Driveshaft, MkIII Roadster, All New, High Speed Balanced, HD Special 28 Spline Yoke for use with AOD Automatic Transmission. Made in USA. $ Denny s Driveshaft, MkIII Roadster, All New, High Speed Balanced, HD 31 Spline Yoke for 4.6 L Engine using T-45 or 3650 Transmission. Made in USA Bolt, 12mm Self Locking, High Torque, for Driveshaft to Pinion Flange, OEM Ford $ Micro-Click Clutch Cable Adjuster and Billet Aluminum Quadrant Kit $90.00 Spring-ball detents and a ball bearing race to prevent the clutch cable action from rotating the adjuster. Clear anodized finish. Made in USA Micro-Click Clutch Cable Adjuster $59.00 Our design is made specifically for the MkIII Roadster and retains the Micro-Click detent and bearing feature while the threaded boss seats directly on the FFR steel foot-box front wall. No drilling or screws are required. Made in USA Clutch Quadrant Replaces the factory Mustang self-adjusting unit. Can be installed in two positions to take up more or less initial cable slack. Constant stock radius. Made in USA. $ Flywheel, Billet Steel, 157-tooth, w balance weights for zero, 28.2, and 50 oz.-in. applications. Includes dowel pins. Requires pressure plate screws. SFI approved. 24 lbs. Made in USA by Fidanza. $ printed 09/24/09, Page 2 of 10
3 35095 Flywheel, Aluminum, 157-tooth, w balance weights for zero, 28.2, and 50 oz.-in. applications. Lighter weight means lower moment of inertia which allows your engine to accelerate faster! Includes dowel pins. Requires pressure plate screws. SFI approved. 11 lbs. Made in USA by Fidanza. $ Fidanza Aluminum Flywheel and Carbon/Kevlar 10- Spline Clutch Combo (use with T-5 or TKO-500 transmissions) $ Fidanza offers a special combo price on their Aluminum Flywheel and Carbob/Kevlar Clutch. The lightweight aluminum flywheel (11 lbs) comes with balance weights for zero, 28.2 and 50 oz-in balanced small block Ford engine applications and includes dowel pins. The Fidanza 2.1 Performance Clutch Kit includes a pressure plate with 2400lb clamping force (OEM units are 1700lbs) without being hard on the leg, release and pilot bearings and an alignment tool. Torque rating is up to 530 ft-lb. This package price represents a $ $ savings over the flywheel ($375.00) and clutch kit ($ for 10 spline, $ for 26 spline) ordered separately! Requires 6 each Pressure Plate Screws for installation Fidanza Aluminum Flywheel and Carbon/Kevlar 26- Spline Clutch Combo (use with TKO-600 transmissions) $ Same description as above but with a 26 spline clutch disc to fit the TKO-600 Transmission input shaft Clutch Cable, Aftermarket, Non-adjustable $ Circlip, Clutch Cable Retainer $ Shield, Clutch Fork Cover $44.00 with stainless attaching screw (Ford List $46.58) printed 09/24/09, Page 3 of 10
4 30154 Fork, Clutch Release, OEM Ford $ Stud, Clutch Fork Pivot, OEM Ford $ Bearing, Clutch Release $29.95 FC Bearing, Transmission Input Shaft Pilot $ Flywheel Bolt Kit, ARP Made in USA. $ Screw/Washer, Pressure Plate to Flywheel (6 per car) M8 x 1.25 x 20mm for Ford 5.0 compatible pressure plates $ Dowel Pin, Flywheel (3 per car) $ M-6397-A302 Pressure Plate Screw and Dowel Pin Kit For dowel pin only order For screw only order $13.50 printed 09/24/09, Page 4 of 10
5 35102 Bellhousing, M-6392-E, Aluminum 302/ 351 to T-5 Transmission This is the stock Mustang 5.0 replacement and can be used to mate 302 or 351 blocks to the T-5 Transmission. Weighs 11lb. Includes clutch fork pivot ball stud. Takes the Clutch Fork Cover. $ M-6392-R58 Cobra R Bellhousing $ Bellhousing Kit, QuickTime RM6060, Steel, 302/351 to T- 5/ Tremec TKO Transmission This new steel bellhousing by QuickTime Inc is precision manufactured in USA to reduce weight and eliminate installation complexities common to other steel bellhousings. $ Does not require run-out checking and adjustment for street applications. Lowest point is equivalent to the bottom of the OEM mid-plate, so no trimming is required. This feature-packed kit includes the clutch fork pivot, block plate, centering rings for T-5 and TKO transmissions, and all fasteners for transmission, block and starter. The starter nose area is open. See for starter nose cover. There is no clutch fork cover available. Weight is 22.5 lb. Finish is semi-gloss black powder-coated Bellhousing Kit, QuickTime RM6065, Steel, Small Block Ford to T-5/TKO/T-5 Transmission, SFI Approved Includes block plate and all fasteners. See for starter nose cover. $ Starter Cover, Spun Aluminum for QuickTime RM6060 and RM6065 $ RM 8030 QuickTime Steel Bellhousing, Small Block Ford to T-56 Trans. Includes Fasteners This new steel bellhousing by Quick Time Inc is precision manufactured in USA to reduce weight and eliminate installation complexities common to other steel bellhousings. $ printed 09/24/09, Page 5 of 10
6 71018 EzePak Fasten-Driveline Talk about handy! Here are all the external fasteners for your driveline that are common to solid axle and IRS, with aluminum bellhousing. 44 pieces include: Engine mount nuts and bolts Starter to bellhousing bolts Mid-plate to bellhousing bolts Bellhousing to engine bolts Transmission to bellhousing bolts Transmission mount nuts and bolts Pinion flange bolts EzePak Fasten Driveline for FFR Complete Kits $48.00 $20.00 Same as above, but without the pinion flange bolts and engine mount nuts and bolts, which are supplied by Factory Five. Note: For TKO, mention in special instructions and add $ Super-Duty T-5 Transmission SHD World Class T-5 Transmission (M-7003-Z). 330ft-lb capacity, st,.63 5th. 10 spline input accepts M C302N HD Low Effort King Cobra Clutch, 28 spline output $1, Tremec TKO-500 Transmission Tremec TKO-500 Transmission (M-7003-R58W) st,.68 5th. 10 spline input accepts M-7560-C302N HD Low Effort King Cobra Clutch, 31 spline output. Requires M-6392-R58 aluminum bellhousing or Quick Time steel bellhousing. $2, Tremec TKO-600 Transmission Tremec TKO-600 Transmission (M-7003-R58H) st,.68 5th. 26 spline input (accepts #35293 clutch kit), 31 spline output. Requires M-6392-R58 aluminum bellhousing or Quick Time steel bellhousing. $2, Mount, Transmission, Energy Suspension, Polyurethane, Black Includes transmission mount to frame fasteners. Made in USA. $30.00 printed 09/24/09, Page 6 of 10
7 35066 HD Clutch Kit, M C302N, Low Effort (use with T-5 and TKO-500 transmissions) Includes clutch disk, pressure plate, and release bearing. $ Fidanza 2.1 Carbon Kevlar Clutch Kit, 10-Spline Disc (use with T-5 and TKO-500 transmissions) $ Includes clutch disk, pressure plate, release and pilot bearings, and alignment tool Fidanza 2.1 Carbon Kevlar Clutch Kit, 26-Spline Disc (use with TKO-600 transmissions) $ Includes clutch disk, pressure plate, release and pilot bearings, and alignment tool Boot, Shifter to Transmission, T-5 $ S Seal, Transmission Extension Housing $ Seal and Bushing Kit, Transmission Extension Housing $ Friction Modifier $ Fitting, Vent, Solid Axle $ Bearing, Rear Axle $15.95 printed 09/24/09, Page 7 of 10
8 8660S Seal, Rear Axle $ Axle Set, Fox Length, 5 on 4.5 bolt circle, Center Hub to Fit Turbo-Coupe Rear Rotors 28 spline with studs installed $ Axle Set, Fox Length, 5 on 4.5 bolt circle, Center Hub to Fit Rear Mustang Rotors 28 spline with studs installed $ RA311 Bearing Kit, 8.8 Differential Includes: Pinion and carrier bearings, pinion nut and seal, crush sleeve, silicone sealer, and gear marking compound. Note: IRS center section also requires 2 ea. FC66998 Axle Bearings and 2 ea seals purchased separately. $ M-4033-G1 Differential Girdle, Ford Racing Cast aluminum differential support cover with load bearing bolts for 8.8 solid axle. The best feature is that it includes fill and drain plugs. Made in USA. $ M-4006-B " Trac Lok Rear with 3.73:1 Gears IRS Differential Carrier Bushing Set, Energy Suspension, Polyurethane, Black $ IRS Differential Rear Mount Fastener Kit $11.00 Includes: Class mm Bolts, Washers, Self-Locking Flange Nuts printed 09/24/09, Page 8 of 10
9 FC66998 Bearing, Independent Rear Axle to Differential Housing $ Fitting, Vent, IRS Center Section $ Seal, Independent Rear Axle $ EzePak IRS CV Joints and Axle Assembly $ Skip the nasty part of an IRS build! Find a whole day of free time! Know that you have all new CV joint assemblies. This EzePak really does make your life a whole lot easier. First, check to be sure you have the correct axles. Standard axles measure 18" while "Pin Drive" axles are 15.5" long. Once you are sure you have the correct axles, ship the axles only (no need to send grease or boot kits) to: Breeze Automotive, LLC 2341 NW 71st Place Gainesville, FL You will receive back a brand new pair of heavy duty CV Joint/Axle assemblies, made in USA.. Actual UPS Ground return shipping will apply. This is a 45lb package. We recommend you paint the axles between the inner boot grooves before shipping Differential Carrier Assembly, Cast Iron, with Trak-loc Differential A remanufactured Traction-loc Center section, cast iron case, modified with magnetic bottom drain plug, aluminum cover, all new 3.55:1 gears, clutches, spider gear axle, bearings and seals. 28 spline. Precision set-up. Recommended all HP levels. Made in USA Differential Carrier Assembly, Cast Iron, with Torsen Differential A remanufactured center section with Torsen differential, cast iron case, modified with magnetic bottom drain plug, aluminum cover, all new 3.55:1 gears, clutches, spider gear axle, bearings and seals. 28 spline. Precision set-up. Recommended 400 HP and below. Made in USA. $1, $1, printed 09/24/09, Page 9 of 10
10 35185 M-4204-T28 8.8" T-2 Torsen Differential, 28 Spline $ The ultimate autocross and roadrace differential. Allows maximum corner exit speed the secret to low lap times IRS Differential Support Cover This beefy cast aluminum cover is designed and made in USA by Control Freak Suspensions. Includes differential bearing cap supports, and fill and drain plugs. A nice way to add strength, functionality, and style to your 8.8 IRS differential. $ printed 09/24/09, Page 10 of 10
This is your one stop 4 Speed Toploader shop.
David Kee Toploader Transmissions, Inc. specializes in Ford 4 speed toploader transmissions from 1964 to 1973. We are the world s largest manufacturer of high quality 4 speed toploader parts. We can remanufacture
More informationDavid Kee Toploader Transmissions, Inc. Product Price Guide
Effective Date: March 16, 2009 David Kee Toploader Transmissions, Inc. Product Price Guide Effective Date: October 1, 2017 PARTS FOUND ON EXPLODED VIEW PAGE OF CATALOG DK296-1... 1 1/16 Bearing Retainer...$54.76
More informationREBUILT NV3550 TO FORD BRONCO
KIT CONSISTS OF: PAGE 1 OF 6 Page Rev. Date: 08-15-16 No. Qty Part No. Description 1. 1 26-3550R REMANUFACTURED NV3550 TRANSMISSION 2. 1 Kit 50-9920 TRANSFER CASE ADAPTER & TC SHIFTER BRKT. 3. 1 Kit 712544
More informationTRANSMISSIONS MANUAL
DMR-5023 Stick shift pilot bearing. Knurled for sure fit, self aligning for perfect fit and smooth running and shift. Fits ant GM manual stick transmission crank. Allows GM transmission in Ford cars. DMR-5022
More informationTo Order Call (562)
451 Park Industrial Dr. La Habra CA 90631 Phone: (562) 691-7006 Fax: (562) 691-5708 www.kugelkomponents.com 2017 PRICE SHEET #17 INDEPENDENT FRONT SUSPENSION SYSTEMS For All IFS Powder Coated (Black Only):
More informationNV3550 TO FORD BRONCO
NV3550 TO 1966-77 FORD BRONCO KIT CONSISTS OF: No. 1. 2. 3. 4. 5. Qty 1 1 Kit 1 Kit 1 Kit 1 Kit Part No. 26-3550 50-9920 712544 716000 716099 Description NV3550 TRANSMISSION TRANSFER CASE ADAPTER & TC
More informationSIZE PRESSURE APPLICATION NOTES PN BOLT WEIGHT BOLT STUD FLYWHEEL CIRCLE SET SET TOOTH COUNT
Pressure Plates RAM performance pressure plates are engineered and built to meet the demands of high horsepower street and competition cars and trucks. These are not converted or modified factory stock
More informationLAKEWOOD/QUICKTIME SAFETY BELLHOUSING INSTALLATION INSTRUCTIONS
LAKEWOOD/QUICKTIME SAFETY BELLHOUSING INSTALLATION INSTRUCTIONS Congratulations on your purchase of the finest quality steel bellhousing available today. 100% Manufactured in the USA! Please understand
More informationLATERAL LIMITER KIT TORSION BAR KIT
C42-429 C42-427 LATERAL LIMITER KIT Controls engine and transmission movement during hard acceleration or braking. With 4130 chromoly tubing and brackets, this kit is recommended when using motor plates.
More informationMagnesium Option, Late Model Front Seal, Viton, P/N 67256V Rear Seal, Viton, P/N 67257V Shifter Installed Heat Treated Yoke, P/N
DESCRIPTION OPTION Magnesium Option, Late Model 80100L Front Seal, Viton, P/N 67256V 80109 Rear Seal, Viton, P/N 67257V 80110L Shifter Installed 80112L Heat Treated Yoke, P/N 62946-6 80119-6 Heat Treated
More informationLoader Backhoe Front Axle Parts 2WD & 4WD
Loader Backhoe Front Axle Parts 2WD & 4WD SECTION G LOADER BACKHOE FRONT AXLE PARTS CASE 2WD AXLE PARTS G2 - G5 CARRARO APPLICATIONS G6 - G25 FRONT AXLE KITS G23 - G25 CASE POWER STEERING VALVES & PUMPS
More informationSECTION 3A FRONT DRIVE AXLE TABLE OF CONTENTS SPECIFICATIONS GENERAL SPECIFICATIONS. Description Drive Shaft Type. CV Joint Axle Housing Type
SECTION 3A FRONT DRIVE AXLE TABLE OF CONTENTS Specifications........................ 3A-1 General Specifications.................. 3A-1 Fastener Tightening Specifications......... 3A-2 Component Locator...................
More information2005 Mustang Workshop Manual
SECTION 205-00: Driveline System General Information 2005 Mustang Workshop Manual GENERAL PROCEDURES Procedure revision date: 07/29/2004 Driveline Angle Inspection Printable View (122 KB) Special Tool(s)
More informationDIM Drive Train Systems
2014 NATEF JOB TASKS COMPLETION REQUIREMENT: P1-95% P2-70% P3-25% Student Name: DETAILED COURSE CONTENT II. DRIVE TRAIN A. CLUTCH -- The student will be able to: P1 P2 P3 Level Date 1. Identify causes
More information3.2 quarts Pennzoil Synchromesh transmission fluid (optional, but recommended)
List of tools and materials: Floor jack, jack stands, and car ramps 3/8 drive ratchet, with long and medium extensions 3/8 drive swivel 3/8 breaker bar / cheater bar 7/8 combo wrench 8mm, 10mm, 13mm, 15mm,
More informationTransmission, disassembling and assembling
Page 1 of 27 34-43 Transmission, disassembling and assembling Disassembly sequence Page 34-55. Transmission overview 1-1st gear 2-2nd gear 3-3rd gear 4-4th gear 5-5th gear 6 - Reverse gear Removing and
More informationBig Block Installation
Factory Five Racing, Inc. Big Block Installation 427 Shown here with fuel injection. 1 These instructions are designed to supplement the assembly manual where the assembly process is different from the
More informationIlustrated Parts List
Spicer Drive Axles Ilustrated Parts List Spicer All Wheel 4 x 4 Drive System AXIP-0400 November 1999 Page to Insert The Spicer 4x4 Drive System Axle models and other equipment covered in this publication
More informationM-2300-T 6-Piston Mustang Brake Kit INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationFront Suspension 2015 E-Series REMOVAL AND INSTALLATION Procedure revision date: 08/11/2014. Axle
204-01 Front Suspension 2015 E-Series REMOVAL AND INSTALLATION Procedure revision date: 08/11/2014 Axle 1 N620604 Axle pivot nut 2 N806859 Axle pivot bolt 3 3007 LH/ 3006 RH LH/ 3006 RH Axle Removal NOTICE:
More informationCall for product recommendations and to place your order! Remote Oil Filter Hose Kit, Braided Stainless
Engine Compartment: www.breezeautomotive.com 70080 Remote Oil Filter Hose Kit, Braided Stainless $83.00 This kit connects the remote oil filter to the engine block adapter for cars with shorty headers
More informationTelephone (925) Fax (925) Lawrence Drive, Livermore, CA 94551
Telephone (95) 454-9500 Fax (95) 454-950 5 Lawrence Drive, Livermore, CA 9455 PARTS MANUAL INDEX STEERABLE DRIVE AXLE ASSEMBLY STEERABLE DRIVE END ASSEMBLY BRAKE CALIPER ASSEMBLY TO USE THIS BOOK:. Refer
More informationFor Sale RWHP 1995 Mustang SVT Cobra
For Sale - 800 RWHP 1995 Mustang SVT Cobra 52,000 mile 1995 Mustang Cobra with Rio Red exterior and Black Leather interior. Purchased bone stock by the current owner in December of 2000 with 40,000 miles.
More informationThe many different faces of the T5
The many different faces of the T5 Not all Borg Warner/TREMEC T-5's are the same. The first T-5 five speeds were introduced to market in 1980, in all things, an AMC Spirit/Concord. In 1983, T-5's were
More informationDodge Light Duty Axle Applications. X510-5 September, Supersedes X510-5DSD dated January 1999
Dodge 1999-2001 Light Duty Axle Applications X510-5 September, 2001 Supersedes X510-5DSD dated January 1999 SAFETY INFORMATION WARNING - Failure to follow these instructions could affect vehicle performance
More information1964 1/2-70 Mustang Torque Arm Rear Suspension Installation Instructions
1964 1/2-70 Mustang Torque Arm Rear Suspension Installation Instructions 1-800-984-6259 www.totalcostinvolved.com Version 2 (c) 2008 Total Cost Involved Engineering, Inc. All Rights Reserved. Page 1 of
More informationPARTS MANUAL FOR R22N/H REAR AXLE
PARTS MANUAL FOR REAR AXLE MARMON-HERRINGTON ALL-WHEEL DRIVE 13001 Magisterial Drive Louisville, KY 40223 TABLE OF CONTENTS REPLACEMENT PARTS & WARRANTY CLAIM PROCEDURE......... 3 DIFFERENTIAL CARRIER
More informationTRANSMISSION INSTALLATION CONTENTS
A REGAL-BELOIT Company TRANSMISSION INSTALLATION CONTENTS RICHMOND 6-SPEED TRANS AM, CAMARO, CHEVELLE, GTO, CUTLASS, WITH T-10/MUNCIE............2 RICHMOND 6-SPEED 1963 TO 1982 CORVETTE WITH T-10 OR MUNCIE..............................3
More informationMERITOR PRODUCT PORTFOLIO FOR THE AFTERMARKET THE RIGHT PARTS FOR THE RIGHT POINTS OF YOUR JOURNEY.
MERITOR PRODUCT PORTFOLIO FOR THE AFTERMARKET THE RIGHT PARTS FOR THE RIGHT POINTS OF YOUR JOURNEY. UPTIME FROM START TO FINISH. At Meritor, we re going to every extreme to deliver the uptime that your
More informationCONVERTING NON POSI REAR END TO POSI Chevrolet passenger car and Corvette
By Tom Parsons CONVERTING NON POSI REAR END TO POSI 55 64 Chevrolet passenger car and 56 62 Corvette This article will be specifically directed at converting the 55-64 Chevrolet full size pass car and
More informationM-4851-M8A SUPER 8.8 IRS MUSTANG AUTOMATIC PINION FLANGE KIT
Please visit fordperformanceracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND
More informationCLICK for More Info Online
CLICK for More Info Online Floater Axle System and Radial-Mount Caliper with Drum-Style Parking Brake System Today s top pro-touring, autocross and road race vehicles often feature some of the largest
More informationHalfshaft. Special Tool(s) Differential Plug (T89P-4850-B) Differential Seal Protector Halfshaft Removal Tool
Halfshaft Special Tool(s) Differential Plug 205-294 (T89P-4850-B) Differential Seal Protector 205-461 Halfshaft Removal Tool 205-475 Hub Remover/Replacer 204-069 (T81P-1104-C) Metric Hub Remover Adapter
More informationListed below are updated Bills of Material (B/M) that are in the Dodge, X510-5DSD parts catalog. Please make the following changes to your catalog.
DSD BILLS OF MATERIAL DODGE CATALOG CORRECTIONS DATE: December 15, 1997 AXL-PNI-40 PART NUMBER TO: All Spicer Light Axle Distributors Listed below are updated Bills of Material (B/M) that are in the Dodge,
More informationPage 1 of 7 Section 05-03A: Axle, Front Drive, Dana Models 44 and 50 1996 Bronco/F-Series Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 06/19/2000 Hubs, Automatic Lock Refer to Section
More informationFactory Five Racing, Inc. Roadster Complete Kit Assembly manual revision 3p update
Factory Five Racing, Inc. Roadster Complete Kit Assembly manual revision 3p update Kit Parts Prep...3 Body Removal...3 Aluminum Removal...5 Front upper control arm...7 Adjusting the upper control Arm...10
More informationREMOVAL AND INSTALLATION
204-00-1 Suspension System 204-00-1 REMOVAL AND INSTALLATION Wheel Bearing, Hub, Knuckle, Upper Arm and Lower Arm Rear Special Tool(s) 3. Remove the parts in the order indicated in the following illustrations
More informationMANUAL TRANSMISSIONS Mitsubishi F4M20, F5M20, F5M30 & KM200 Series TRANSMISSION APPLICATION
Article Text ARTICLE BEGINNING MANUAL TRANSMISSIONS Mitsubishi F4M20, F5M20, F5M30 & KM200 Series APPLICATION TRANSMISSION APPLICATION Vehicle Application Transmission Model Chrysler Motors (2WD) 4-Speed
More informationSPARE PARTS BOOK. Front Axle FSDP-09/10-S. Book No. 201 (12/2009)
SPARE PARTS BOOK Front Axle S Sisu Axles, Inc. Autotehtaantie 1 PO Box 189 FIN-13101 Hameenlinna Finland Phone +358 20 55 2999 Fax +358 20 55 2900 1.12.2009 1 Axle L577 10 8 9 12 1 13 11 "A" "B" 6 5 1
More informationINSTALLATION INSTRUCTIONS 88518
INSTALLATION INSTRUCTIONS 88518 For Rancho Suspension Systems RS6518: 2009 FORD F-150 4WD READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev A IMPORTANT NOTES! WARNING:
More informationConverting a Chevy Non-positraction rear-end to a positraction rear using an Eaton posi unit.
Converting a 56-62 Chevy Non-positraction rear-end to a positraction rear using an Eaton posi unit. Tom Parsons Non-posi unit Posi unit 1 Converting a 56-62 Chevy Non-positraction rear-end to a positraction
More informationM-2300-M Mustang GT Rear Disc Brake Bracket Kit INSTALLATION INSTRUCTIONS
Please contact the Tech Line for the most current instruction information (800) 367-3788!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! INTRODUCTION: This kit allows for the
More information2017 Thunder Series 602 Thunder Series Rules
2017 Thunder Series 602 Thunder Series Rules Chassis: 1. Must follow FASTRAK rules. 2. Chassis must be built prior to 2014 Body: 1. Must follow FASTRAK body rules 2. 8 spoiler permitted 3. No 12 side braces
More information04-08 FORD F150 6 KIT
957600 THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. 0-08 FORD F50 6 KIT Rough Country recommends a certified technician install this system. In addition to these instructions, professional
More informationFRONT AXLE PARTS BOOK TH636C TH644C TH842C TH844C
I FRONT AXLE PARTS BOOK TH636C TH6C THC THC I DATE: --05 SPICER CLARK-fnJRTH /60 AXLE 7-9-69 STEERENG CYUNDER DIFFERENTIAL LOCK TEREX HANDLERS 55 N. Superior Ave., Baraga, MI 990 PH: (906) 353-3500; FAX:
More informationX Light Axle Parts for Nissan Applications August 2014
Light Axle Parts for Nissan Applications August 2014 The Spicer is a comprehensive catalog that delivers the information you need about light axle parts for Nissan applications all in one convenient place.
More informationTION AND OPERATION Procedure revision date: 01/22/1999
TION AND OPERATION Procedure revision date: 01/22/1999 Main Components and Functions AX4S Main Components http://www.fordtechservice.dealerconnection.com/pubs/content/~wsww/~mus~len/20/sww71006.htm (1
More information*1576BAG9* 1576BAG FORD F KIT C THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS.
957600C THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. 0-08 FORD F50-6 KIT Rough Country recommends a certified technician install this system. In addition to these instructions, professional
More informationMustang Clutch Cable Installation Instructions
Five and Six speed conversion specialists" 1965-66 Mustang Clutch Cable Installation Instructions Tool List Hand drill, 1 unibit drill, 7/16 wrench, two ½ wrenches, two 9/16 wrenches, 1/2 ratchet, 9/16
More informationFirst, check and record the camber and caster readings, they will be adjusted later.
First, check and record the camber and caster readings, they will be adjusted later. The caliper-mounting bosses are machined perpendicular to the spindle so they are an excellent place for the level.
More informationDemand the original. Axle Components
Axle Components Driveshaft Components Repair Kits Axle Components OE Quality Driveline Components Designed for Chrysler RAM Products Axle Components Driveshaft Components Repair Kits Only original equipment
More informationSPARE PARTS BOOK. Rear Tandem Axle FRDP FRDP16S0879/011&013 Up to S/N (Nov 2004) Book No. 247 (2/2007)
SPARE PARTS BOOK Rear Tandem Axle ) Sisu Axles, Inc. Autotehtaantie 1 PO Box 19 FIN-101 Hameenlinna Finland Phone +35 20 55 99 Fax +35 20 55 00 2.2.2007 1 Axle L71 2 1 5 3 9 7 10 11 1 1 15 Breather 1 Breather
More informationMUSTANG FLYER MARCH 2018
MUSTANG FLYER MARCH 2018 AJM000 Catalogue of early Mustang parts available. Will help you see if what you want is available 03.60 ACCESSORIES: AJM060 Fender/wing cover 21.62sp BUMPERS AJM002 64-66 Front
More informationPRE-INSTALLATION. INSTALLATION INSTRUCTIONS Front Ford F150 4WD 4" Suspension Lift Kit
2015 Ford F150 4WD 4" Suspension Lift Kit PRE-INSTALLATION 2 - Knuckle (Driv/Pass) 2 - Crossmember (Front/Rear) 2 - Differential Bracket (Driv/Pass) 1 - Diff. Brace Bracket (Pass) 2 - Front Brake Line
More informationAUT 231 (A3) MANUAL TRANSMISSION/TRANSAXLE AND DRIVETRAIN
AUT 231 (A3) MANUAL TRANSMISSION/TRANSAXLE AND DRIVETRAIN COURSE DESCRIPTION: Prerequisites: TRN 120 Corequisites: None This course covers the operation, diagnosis, and repair of manual transmissions/transaxles,
More information2015 SLED PULL Rules and Regulations
Super Stock Diesel Trucks Maximum weight of 7500lbs with driver. All drivers must have a valid state driver s license OEM or equivalent SFI restraint system is mandatory and must be worn. 2015 SLED PULL
More information1984 Dodge W250 PICKUP
1984 Dodge W250 PICKUP Submodel: Engine Type: V8 Liters: 5.2 Fuel Delivery: CARB Fuel: GAS Dana 44 MODELS THROUGH 1984 2. Raise and safely support the vehicle, then remove the wheel hub and bearings as
More informationFord Frame and Suspension
20 1941-48 FORD Hot Rod Suspension Parts Please see page 12 For information on our 1941-48 Frame exchange program FRONT SHOCK KIT Super strong - 3 point mounting on upper bracket insures against breakage.
More informationUSE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT:
1962-1967 Chevy Nova Pro-Touring Front Suspension Installation Instructions Tech line: 1-855-693-1259 www.totalcostinvolved.com Read and understand these instructions before starting any work! USE THE
More informationAxle Components. 12,000 lbs. Capacity
12,000 lbs. Heavy Duty Components 27-358 Unitized Oil Seal - disc or drum (Dimensions are 3.125 x 4.506 x.605) 2 010-056-00 27-342 3984 Inner Bearing (Inside diameter 2.625 ) 3 031-020-02 27-343 3920 Inner
More informationFeatured Products STAY CONNECTED TOLL FREE: CLUTCH.1. Page 4. Page 9. Optimum-V Clutches. 5.5" Steel Bellhousing Kits
Featured Products Page 4 Page 9 5.5" Steel Bellhousing Kits Optimum-V Clutches Page 11 Page 16 Service Kits Ultra-Duty Starters Page 21 Page 24 Carbon Fiber Driveshafts Quick Change Gears STAY CONNECTED
More informationHeavy Duty Front-Drive Steer Axles MX-140 and MX-160 Series
Revised 11/2009 Heavy Duty Front-Drive Steer Axles MX-140 and MX-160 Series Catalog PB-0349 Strength Power Speed Agility MERITOR PARTS. RIGHT FROM THE START. TABLE OF CONTENTS MX-17/19/21-140 and MX-21/23-160
More informationDISASSEMBLY AND ASSEMBLY (Continued)
205-03-23 Front Drive Axle/Differential Ford 8.8-Inch Ring Gear 205-03-23 49. Measure the ring gear backlash at four places to obtain a consistent reading. 1 Mount the special tools on the indicator base.
More informationIllustrated Parts List
Spicer Drive Axles Illustrated Parts List AXIP0201 September 2006 DSH40(P), DSH44(P), DDH40(P), DDH44(P), RSH40, RSH44, RDH40, RDH44, 22060SH TABLE OF CONTENTS TABLE OF CONTENTS Models... 2 General Information...
More informationSPARE PARTS BOOK. Rear Tandem Axle FRDP-13/16-S. Since No (11/2004) Book No. 292 (5/2009)
SPARE PARTS BOOK S Sisu Axles, Inc. Autotehtaantie 1 PO Box 189 FIN-13101 Hameenlinna Finland Phone +358 204 55 2999 Fax +358 204 55 2900 31.1.2012 1 Axle L870 2 1 11 12 12 5 12 10 12 3 9 6 4 7 15 13 14
More informationTRANSAXLE
5072-10 5080-10 BUGPACK SUPER DIFFS After years of intensive research, we are now able to offer the FINEST transaxle Super Diffs ever made. Starting with a high quality, nonporous steel alloy casting and
More informationOVERVIEW: KIT INCLUDES:
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More information2014 SLED PULL Rules and Regulations
Maximum weight of 7500lbs with driver. Diesel Super Stock Trucks 2014 SLED PULL All drivers must wear a helmet (Must have helmet meeting Snell SA2005, K2005, M2005, SA2010, SAH2010, K2010, M2010 or SFI
More information2004 DRIVELINE/AXLE. Rear Drive Axle - Corvette. Fastener Tightening Specifications Specification Application
2004 DRIVELINE/AXLE Rear Drive Axle - Corvette SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Differential Case Bolts 55 N.m
More informationSPARE PARTS BOOK. Front Axle SSDP-12-S. Book No. 209 (4/2010)
SPARE PARTS BOOK Front Axle Sisu Axles, Inc. Autotehtaantie 1 PO Box 189 FIN-13101 Hameenlinna Finland Phone +8 20 2999 Fax +8 20 2900 16.8.2012 1 Axle L96 2 22 2 7 8 9 10 20 21 1 26 27 22 2 23 19 13 21
More informationINSTALLATION INSTRUCTION 88148
INSTALLATION INSTRUCTION 88148 Rev C For Rancho Suspension Systems RS6548, RS6549 & RS6550: GM 2500HD, 2500, and 1500HD Trucks READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION
More informationSPARE PARTS BOOK. Industrial Axle SRDP SRDP-30-S Since S/N (7/2005) Book No. 349 (6/2007)
SPARE PARTS BOOK Industrial Axle Sisu Axles, Inc. Autotehtaantie 1 PO Box 189 FIN-13101 Hameenlinna Finland Phone +358 204 55 2999 Fax +358 204 55 2900 15.6.2007 1 Axle L1049 5 6 2 1 3 4 11 9 10 13 15
More informationADVANCE ADAPTERS INC. Fixed Yoke kit (S.Y.E. Kit)
ADVANCE ADAPTERS INC. Fixed Yoke kit (S.Y.E. Kit) Instruction Sheet P/N: 50-7905 & 50-7906 KIT CONSISTS OF: No. Qty Part No. Description 1. 1 51-7906 TAILHOUSING, DIECAST 2. 1 52-7905 SHAFT, MAIN OUTPUT
More informationMOPAR B-BODY
MOPAR B-BODY 1962-1970 TKO 5-SPEED MANUAL TO MANUAL TRANSMISSION CONVERSION INSTALLATION MANUAL FOLLOW FACTORY SERVICE MANUAL (FSM) RECOMMENDED SAFETY PRECAUTIONS. TRANSMISSION REMOVAL AND INSTALLATION
More informationINSTALLATION INSTRUCTIONS CHEVROLET NOVA (NVR-301) INDEPENDENT REAR SUSPENSION
INSTALLATION INSTRUCTIONS 68-74 CHEVROLET NOVA (NVR-301) INDEPENDENT REAR SUSPENSION Please read these instructions completely before starting your installation. Assemble suspension on vehicle before powder-coating
More informationSlide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided.
Slide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided. Put the urethane bushings into the upper antiroll-bar-link eyebolt. Coat the bushings
More informationTKO Parts Catalog. January January 2007 TKO Parts Catalog. Technology in motion. Bulletin No. TRAP
TKO Parts Catalog Bulletin No. TRAP0090107 Technology in motion January 2007 January 2007 TKO Parts Catalog i F C A E A F C D A B C TTC 2007, All rights reserved. ii TREMEC Transmissions Contents Contact
More information1994 Mitsubishi Eclipse GS
APPLICATIONS CHRYSLER MOTORS MANUAL TRANS OVERHAUL - MITSUBISHI W5M & W6M SERIES MANUAL TRANSMISSIONS Mitsubishi W5M31, TRANSMISSION APPLICATIONS (CHRYSLER MOTORS) Vehicle Application Transmission Model
More information04-08 FORD F150 4 KIT
9257700 04-08 FORD F50 4 KIT THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. Rough Country recommends a certified technician install this system. In addition to these instructions, professional
More informationM Ring and Pinion Installation
!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. Axle Shaft Removal (1994-2012 Mustang typical) STEP 1: STEP 2: Remove the 10 differential housing cover bolts and drain
More informationMustang GT / GT500 / V6 1 Piece CV Driveshaft
2005 2014 Mustang GT / GT500 / V6 1 Piece CV Driveshaft Not checking this will void the warranty: Please Note: Vehicles with a live rear axle (2005 2014 Mustang) must be checked with the rear suspension
More information4WD RANGER/BRONCO II WD EXPLORER CLASS II INSTALLATION INSTRUCTIONS
4WD RANGER/BRONCO II 8-97 4WD EXPLORER 90-94 CLASS II INSTALLATION INSTRUCTIONS Before beginning the installation, read these instructions and the enclosed driver s WARNING NOTICE thoroughly and completely.
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION AXLE SHAFTS & BEARINGS Removal CAUTION: Failure to turn off air suspension power before raising vehicle may result in unexpected inflation or deflation of air springs. DO NOT reconnect
More informationPBS S4/S5 KIT PICK SHEET
Updated 5/5/15 STANDARD OR OPTION (CIRCLE ONE) STANDARD ITEM OPTION DRIVE FLANGES S45-5934 PBS-5930 BELL HOUSING + MATCHING INPUT SHAFT + MATCHING T/O BEARING PBS-615CHEV-KIT PBS-615VW-KIT STANDARD ITEMS
More informationDRIVE AXLES. Differentials & Axle Shafts - Corvette
DESCRIPTION & OPERATION 1998-99 DRIVE AXLES Differentials & Axle Shafts - Corvette A Getrag 625 model differential is used on both the automatic and manual transmissions. Differential carrier and case
More informationIllustrated Parts List
Spicer Drive Axles Illustrated Parts List AXIP-0487 February 201 S140 Model Table of Contents General Information... 2 How To Use Illustrated Parts List... 2 Model Identification... 3 Axle Parts Explode...
More informationHoffman Auto Racing Sale List
Hoffman Auto Racing Sale List 0/9/0 NEW Winters 4.: w/5: light black axle and Black Thermal coating Winters 4.: Medium weight axle Weld Direct Mount Hubs Ultra light w/ bearings pair Titanium spindles
More informationAxle Components. Demand the original. Axle Components Driveshaft Components Repair Kits
Axle Components Driveshaft Components Repair Kits Axle Components OE Quality Driveline Components Designed for Chrysler RAM Products www.demand.com Axle Components Driveshaft Components Repair Kits Only
More informationMustang Differential Gears - Installation Instructions
Mustang Differential Gears - Installation Instructions The below installation instructions work for the following products: Ford Racing Gears - 3.73 Gears for 8.8" Ford Rear End Ford Racing Gears - FRPP
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS FOR FORGED SUPERLITE BIG BRAKE FRONT HUB KIT WITH 3.00 DIAMETER VENTED ROTOR 968-969 FORD MUSTANG (DISC BRAKE SPINDLE ONLY) PART NUMBER GROUP 0-950 WARNING INSTALLATION OF THIS KIT
More information1 Part Number: M-2300-Y Part Description: S550 Mustang-Shelby Brake Upgrade Kit Installation Instructions
Please visit www.performanceparts.ford.com for the most current instruction and warranty information. PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT
More informationMustang/Cougar Clutch Cable Installation Instructions
Five and Six speed conversion specialists" 1967-68 Mustang/Cougar Clutch Cable Installation Instructions Tool List Hand drill, 1 uni bit drill, 7/16 wrench, two ½ wrenches, two 9/16 wrenches, 1/2 ratchet,
More informationTH400 (3L80), 375, 3L80-HD(475) RWD 3 SPEED Toll Free: Click here to visit our website Page 1
TH400 (3L80), 375, 3L80-HD(475) RWD 3 SPEED Page 1 1 2 3 4 5 6 7 8 9 11 10 12 13 14 15 16 17 18 19 Forward Clutch Drum 20 21 22 23 24 23 25 26 27 28 29 30 31 32 33 34 35 36 37 Direct Clutch Drum 38 39
More informationNext, set the bar level and tighten it down. Do this on both the driver and passenger sides.
Next, set the bar level and tighten it down. Do this on both the driver and passenger sides. Using two tape measures, measure the outside width at the front and the rear of the tubes. The front dimension
More informationModel Series 660 & 670
Model Series 0 & 0 Part. -0A Harness Assembly. -0 Hex TT-Tap Scr. /-0 x. Lg.. -0 Hex Bolt /-0 x. Lg.. -00 Hex Bolt /- x. Lg.. -0 Speed Nut /-0 Thd.. -00A Flange L-Nut /- Thd.. -00 Hex Nut /-0 Thd.. -0
More informationFRONT RACK, BODY PANEL, AND HEADLIGHT ASSEMBLIES
FRONT RACK, BODY PANEL, AND HEADLIGHT ASSEMBLIES 0747-506 1 2506-107 1 Rack, Front - Assembly (inc. 2) 2 0411-576 1 Decal, Warning - Load 3 0441-592 4 Bushing 4 8410-835 4 Screw, Cap 5 0423-669 4 Spacer
More informationALUMINUM & STEEL BELLHOUSINGS & COMPONENTS
ALUMINUM & STEEL BELLHOUSINGS & COMPONENTS B R O W E L L B E L L H O U S I N G. C O M A TRACK RECORD OF PERFORMANCE! Browell Bellhousing custom builds SFI certified, aluminum and steel bellhousings for
More informationDIFFERENTIAL. OL = Overall Length
3 Rear Axle Shafts Blazer 3- Jimmy 3-34-4 REAR AXLE SHAFT -/ GEAR WD BLZ JIM 3- ().44 4. 34- REAR AXLE SHAFT -/ GEAR WD BLZ JIM - () 4.4. 34- REAR AXLE SHAFT -/ GEAR 4WD BLZ JIM 3- ().44 4. 34- REAR AXLE
More informationPart # Mustang Complete CoilOver Kit
Front Components: Part # 12100109 67-70 Mustang Complete CoilOver Kit 1 12103509 Non Adjustable Front CoilOvers 1 12102899 Lower StrongArms 1 12103699 Upper StrongArms Rear Components: 1 12106509 Non Adjustable
More informationPARTS CATALOG MODELS 320, 420, 520, 620, 820 GRAIN CART. Unverferth
Unverferth Manufacturing Company, Inc. P.O. Box 357 Kalida, Ohio 45853 (419) 532-3121 FAX (419) 532-2468 Grain Carts PARTS CATALOG MODELS 320, 420, 520, 620, 820 GRAIN CART Unverferth Manufacturing Co.,
More information