Model AD-29A Automatic Air Spray Gun and Can Marking System
|
|
- Lawrence Gaines
- 1 years ago
- Views:
Transcription
1 Model AD-29A Automatic Air Spray Gun and Can Marking System Part A NORDSON CORPORATION. AMHERST, OHIO. USA
2 2-454d TECHNICAL PUBLICATION Nordson Corporation Finishing Equipment Division ISSUED 4/85 SUPERSEDES CONTENTS Description l. Specifications Theory of Operation Installation... ; Operation Maintenance Troubleshooting Disassembly Exploded View AD-29A Gun Parts List System Parts List LITHO
3 0 NO&on Nordson corporation TECHNICAL PUBLICATION 2-5-l Finishing Equipment Division, Amherst, Ohio 4400 SUPERSEDES ISSUED 485 NORDSON CAN MARKING SYSTEM Figure - Can Marking System DESCRIPTION The Nordson Can Marking System is designed to apply thermal sensitive marking fluid to can bodies prior to their going into the cooking cycle. Then the thermal sensitive marking fluid has been exposed to a specific temperature for a certain length of time, the dot or strip of fluid on the can changes color. Visual inspection of the cans immediately determines whether the canned food or beverage has been sufficiently cooked. The Nordson Can Marking System consists of a spray gun, a solenoid valve, a pressure pot, a metal proximity sensing device, and a solid state timing device. The air spray gun is mounted in a stationary position adjacent to the can body. The pressure pot supplies the gun with marking fluid, while the solid state timer determines how long the spray gun will apply the marking fluid. The duration timer can be adjusted for changes in line speed and variations in can sizes. USA. Q NORDSON CORPORATION 985 All Rights Reserved
4 2-5-2 TECHNICAL PUBLICATION Nordson Finishing Equipment Division ISSUED 485 SUPERSEDES SPECIFICATIONS U.S.A. METRIC Operating Temperature Ambient 2 Operating Air Pressure - Pot 0-40 PSIG kg/cm Operating Air Pressure - Gun PSIG kg/cm 2 Air Consumption - Gun Depends on application 2 SCFM maximum.944 Iiters/sec. Electrical Requirements - Controls 5 VAC, SO/SO Hz., 50 watts Figure 2 - AD-29A Gun W/Solenoid I- c4 A..OO in. (25.4 mm) U E. B in. (58.8 mm) F. c in. (88. mm) G. LW D in. (60.3 mm) Ii in. (7.5 mm) 5.38 in. (36.7mm) 2.00 in. (50.8 mm) 2.28 in. (57.9 mm) Figure 3 - Mounting Dimensions LITHO
5 0 NO&on Nordson corporation TECHNICAL PUBLICATION Finishing Equipment Division, Amherst, Ohio 4400 SUPERSEDES ISSUED 4/85 Figure 4 - Can Marking System Controls r D b-c-4 - I +--+I Proximity Amplifier Enclosure Model FET- Timer Figure 5 - Mounting Dimensions A in. (254.0 mm) A..50 in. (292. mm) B in. (90.5 mm) B in. (203.2 mm) c in. (4.3 mm) c. 4.2 in. (06.7 mm) D in. (84.2 mm) D in. (273. mm) E in. (33.4 mm) E in. (52.4 mm) U S A. Q NORDSON CORPORATlON 985 All R,-htc F)ecor~md
6 2-5-4 TECHNICAL PUBLICATION Nordson COtpOratiOn Finishing Equipment Division ISSUED 485 SUPERSEDES Proximity AD-29A Dua I Regulators Main SUPP Y Air Figure 6 - System Diagram THEORY OF OPERATION The Nordson Can Marking System consists of a spray gun (Model AD-29A), a solenoid valve, a 2 gal. pressure pot, a metal proximity sensing device, and a solid state time interval control (Model FET-). The pressure pot is available with an agitator also for fluids that may require agitation. Air is supplied to the pressure pot through a dual regulator. Atomizing air is supplied to the gun by a 3/8 O.D. polyethylene hose, while the marking fluid is delivered to the gun by a l/4 0. D. polyethylene hose. The AD-29A gun has a single pressure orifice to deliver marking fluid to the cans. Atomizing air is directed to the fluid through four air ports located in the air cap. A solid state duration timer will control the length of the spray pattern. The timer is signaled by a metal proximity sensing device. Fluid flow rate is directly related to the air pressure applied to the pressure pot. The flow rate can be further refined by adjusting the gun needle lift by using the adjustment screw at the top of the gun. NOTE: During operation cans must be aligned individually directly in front of the spray gun. LITHO U
7 Nordson Corporation TECHNICAL PUBLICATION 2- Is-5. Finishing Equipment Division, Amherst, Ohio 4400 INSTALLATION SUPERSEDES ISSUED 4/85 GUIDELINES. The Can Marking System should be installed in an area where: a. The cans are dry and free of oil. b. The ink on the cans has time to dry before the cans go into the cook cycle. 2. If the ink you are using requires agitation be sure to use the pressure pot with agitator, Nordson P/N Keep fluid line as short as possible. 4. AD-29A Can Marking Gun: a. It is recommended the gun be mounted to shoot horizontally or downward. b. Position the gun approximately l/2 inch from the can. c. The needle travel adjustment should be set as follows:. Loosen the locking nut 2. Turn the adjustment screw full clockwise until it stops (bottoms out against the needle) 3. Turn the adjustment screw counter-clockwise l/2 turn 4. Tighten the locking nut 5. The cans must pass by the gun in single file -- no overlapping. 6. Proximity Sensor: a. Mount the sensor directly above or below the gun. b. Position the sensor approximately l/4 inch from the can. NOTE: It is important not to have other metal objects near the sensor surface.. IJ S A. Q NORDSON CORPORATION 985 All Rights Reserved
8 2-5-6 TECHNICAL PUBLICATION Nordson COrpOratbn Finishing Equipment Division ISSUED 4/85 SUPERSEDES INSTALLATION Using a stationary type stand or bracket, (l/2 dia. bar, customer supplied) install the AD-29A spray gun at a distance of approximately l/2 to l-/2 inches from the can body, in the following manner:. Attach the solenoid valve to the gun using the l/8 NPT close nipple and l/4 NPT to l/8 NPT reducer and position gun approximately l/2 from the can body. Make certain all fittings are tightened securely. 2. Mount the FET- Timer and proximity amplifier enclosure near the work area. Make certain these controls are located in a protected area so that they do not come in contact with steam or cleaning material used in the cleaning operation. Also, do not subject these controls to excessive vibration or extreme ambient temperatures. 3. Mount the proximity amplifier in the enclosure. 4. Install the proximity sensor so it is mounted directly above or below the gun. 5. Connect the FET- Timer to the proper input power supply. Refer to the FET- Timer service manual for complete installation instructions. Electrical connections for the proximity amplifier are detailed on page Connect the fluid filter assembly to the pressure pot. 7. Attach an air supply line to the inlet side of the 3/8 NPS dual regulator assembly. 8. Attach l/4 NPS x l/4 NPT connector to the dual regulator assembly s output side. 9. Secure a l/4 NPT x l/8 NPT reducer to the connector. 0. Attach a l/8 NPT x 3/8 tube compression fitting to the reducer.. Secure the 3/8 black polyethylene tube to the compression fitting. 2. Secure the 3/8 black polyethylene tube to solenoid on the gun with another l/8 NPT x 3/8 tube compression fitting and another l/4 NPT to l/8 NPT reducer. 3. Attach the 3/8 NPS x l/4 NPT connector to the filter assembly on the pressure pot. 4. Secure another l/4 NPT x l/8 NPT reducer to the connector. 5. Install the 8 NPT x l/4 tube compression fitting. 6. Secure the l/s natural polyethylene tubing to the compression fitting. 7. Attach the open end of the natural tubing to the fluid inlet on the gun. LITHO U
9 Nordson Corporation TECHNICAL PUBLICATION Finishing Equipment Division, Amherst, Ohio 4400 SUPERSEDES ISSUED 4/85 OPERATION Before using the Nordson Can Marking System make certain that all air line and fluid line fittings are securely tightened and all electrical connections are properly completed and protected from damage. A 5 Make sure the pressure pot, proximity sensor, amplifier, timer, and solenoid are electrically grounded. Confirm that the AD-29A gun is securely mounted and positioned correctly. NOTE: If the gun is not positioned properly, the cans will not be accurately marked with the thermal sensitive ink. The air supply to the pressure pot must be clean and dry for the thermal sensitive ink to function properly. Initial Start-up. Set the FET- Time Interval Control to the low range setting (Refer to the FET- manual for the location of the slide switch). 2. Set the FET- Time Interval Control s delay to 0.00, Low Scale. 3. Set the FET- Time Interval Control s duration at the minimum setting for a consistent pulse. (Start at some refinement of the duration sequence may be necessary once the line begins to run.) 4. Pour the thermal sensitive ink into the pressure pot after loosening four (4) clamps and removing the cover. 5. Close the pot and secure all four (4) clamps. 6. Apply air pressure to the pot. a. fluid pressure - approximately 20 PSIC (45 PSIG Max.). b. gun air pressure - approximately 50 PSIC (70 PSIG Max.). NOTE: Final fluid pressure adjustment should be made at the fluid pressure regulator to obtain the desired deposit on the can - not by changing the gun needle adjustment. 7. Turn the FET- Time Interval Control llon l. The Nordson Can Marking System is now ready for operation Shut Down NOTE: Keep the system pressurized unless opening and refilling the pressure pot or removing pressure lines. By keeping the system pressurized, the ink will not drain out of the fluid lines. Keeping the fluid lines full will prevent ink residue from plugging the hoses and guns.. Shut off FET- Timer. Q, NORDSON CORPORATION 985 All Rights Reserved
10 2-5-8 TECHNICAL PUBLICATION Nordson COrpO! ation Finishing Equipment Division OPERATION ISSUED 4/85 (Continued) SUPERSEDES Start-Up. Turn on FET- Timer. 2. If possible, position substrate in front of gun and fire it a few times. Refillina the Pressure Pot. Shut off air pressure to pot. 2. Open pot relief valve. A T 0 es Do not loosen clamps until all pressure has been relieved. 3. Loosen four (4) clamps and remove pot cover. 4. Agitate fresh ink supply briefly. 5. Pour fresh ink into pot. NOTE: To keep the pot, fluid lines, and guns clean, it is a good idea to use a liner in the pot. This liner can be alternated as the pot is refilled keeping skimming of the pot at a minimum. 6. Close the pot and secure the four (4) clamps. 7. Turn on air pressure to the pot. MAINTENANCE The Can Marking system requires some daily maintenance to keep the system working at optimum levels.. Remove the air cap and clean the air ports and the area around the nozzle seat of all residual ink. Use a soft bristle brush only. Do not damage air cap or nozzle. 2. Check the inline filter on a regular basis. 3. Do not allow the inside walls of the pressure pot to skim over. 4. Flush the hydraulic part of the system regularly with fresh material if the system sits idle for any length of time (especially if the ink has fillers in it). LITHO U
11 Nordson Corporation TECHNICAL PUBLICATION 2-5-g Finishing Equipment Division, Amherst, Ohio 4400 SUPERSEDES ISSUED 4/85 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE Ink flowing, no atomization Atomizing air ports blocked. Ink flowing, atomization too Atomizing air ports blocked. soarse Ink flowing, atomization too Gun solenoid exhaust port blocked. fine No ink flow Pressure pot not sufficiently pressurized. No air pressure to gun. Timer not IOn? Timer not functioning. Gun solenoid failed. Needle lift improperly adjusted. Fluid line blocked. Air line blocked. Pressure pot empty. Ink build up on needle or nozzle. Too little ink flow Pressure pot not sufficiently pressurized. (20 PSIG /.4 kg /cm2 optimum). Needle lift adjusted too low. Fluid line blocked. Fluid filter plugged. Ink build up on needle or nozzle. Too much ink flow Pressure pot over 45 PSIW3.6 kg/cm2. Needle lift adjusted too high. Improper ink pattern (width) Atomizing air port(s) plugged. Fluid seat blocked. Ink dried on needle face. Gun positioned improperly. Improper ink pattern (length) Triggering device malfunction. Timer set incorrectly. Timer malfunctioning (see appropriate manual). Air escaping from ports in AD-29A air cylinder cover Ink leaking from ports in AD-29A cylinder cover or solenoid Piston seals need lubrication or replacement. Needle packing needs NORDSON CORPORATION 985 All Rights Reserved
12 TECHNICAL PUBLICATION Nordson COrpOratiOn Finishing Equipment Division ISSUED Q/85 SUPERSEDES AD-29A DISASSEMBLY The AD-29A gun disassembled by removing and nozzle/seat from the extrusion end of the gun. numbers and Loosen the air cylinder AD-29A REASSEMBLY To reassemble the D-29A gun, insert the nylon seal washer 2 in the gun body. 0 Place the O-ring in the recess located at the lower end of the needle packing Q 0. Insert the needle packing in the gun body. Thread the needle packing 0 securely in the gun body. Use a small amount of grease to lubricate the packing and needle as these parts are installed in the gun body. NOTE: Be certain the needle packing is tightened securely in the gun body. the shaft of the shut off Place the piston seal 6 over the piston and secure this assembly with the 0 Insert the needle assembly through the packing until the shut at the extrusion end of the gun. Place the piston ack-up on top of the air piston and thread the air cylinder cover 3 on the gun Complete r assembly by threading 6 seat 9 into the gun body, place the air cap 20 in the retaining nut 0 securing the retaining nut to the extrusion end 6 o the gun. LITHO U
13 Nordson Corporation TECHNICAL PUBLICATION 25- Finishing Equipment Division, Amherst, Ohio 4400 SUPERSEDES ISSUED f+/85 RESERVED FOR FUTURE NORDSON CORPORATION 985 All Rtghts Reserved
14 2.,5-2 TECHNICAL PUBLICATION Nordson Finishing Equipment Division ISSUED f+/85 SUPERSEDES 4 2 Figure 7 - AD-29A LITHO
15 a NO&On Nordson Corporation TECHNICAL PUBLICATION Finishing Equipment Division, Amherst, Ohio 4400 SUPERSEDES ISSUED W85 Key Part No. Description Gun, AD-29A Screw, Needle Stop Nut, Locking Cover, Air Cylinder Spring, Piston Back-Up Nut, Lock, Hex, l/ Washer, Piston Seal Seal, Piston Piston : Needle, Shut Off Packing, Needle O-ring, Viton, l/8 x l/ Washer, Seal 3. Body, Gun w/nameplate, AD-29A.. Body, Gun, AD-29A Nameplate, AD-29A Connector, l/8 NPT x l/4 Tube Mounting, Retainer Screw, Sq. Hd., 3/ Screw, Fil. Hd., lo-32 x l-/ Plug, Pipe, l/8 NPTF : Nozzle/Seat, AD-29A Air Cap, AD-29A Nut, Retaining Req d NORDSON CORPORATION 985 All Rights Reserved
16 TECHNICAL PUBLICATION Nordson Finishing Equipment Division ISSUED Q/85 SUPERSEDES 5 Figure 8-Optional Pressure Pot Figure 9 - Installation Components w/agitator POT AIR Figure 0 - System Components LITHO U
17 0 NO&On Nordson Corporation TECHNICAL PUBLlCATlON 2 I- 5-5 Finishing Equipment Division, Amherst, Ohio 4400 SUPERSEDES ISSUED 4/85 SYSTEM COMPONENTS Fig. Key Part No. Description Req d Pressure Pot, w/agitator, 2 Gal. (Optional) Bushing, Reducing, l/4 NPT x l/8 NPT Kit, Installation Connector, Swivel, l/4 NPT x l/4 NPS Connector, Swivel, l/4 NPT x 38 NPS : Connector, Tube, 3/8 O.D. x l/8 NPT Connector, El bow, 8 NPT x 38 Tube Connector, Male, 4 O.D. x l/8 NPT Reducer, l/4 NPT x l/8 NPT Wrench, Adjusting Gun, AD-29A, Can Marking Valve, Solenoid, 24 VDC, Explosion Proof FET-, Time Interval Control, 20 VAC Enclosure, Proximity Amplifier Amplifier, Proximity Sensor, Proximity Pressure Pot, 2 Gal Filter Tubing, 3/8 O.D., Polyethylene, Black, ft Tubing, l/4 O.D., Polyethylene, Natural, ft. NS NS Filter, Air NS NS Connector, Swivel NS NS Reducer, 3/8 NPS x l/4 NPT U S NORDSON CORPORATION 985 All Rights Reserved
18
Paint/Solvent/Dump Valve and Flow-Through Valve
Instruction Sheet P/N 08573D Paint/Solvent/Dump Valve and Flow-Through Valve. Description See Figure. The paint/solvent/dump valve is a normally-closed valve that opens to trigger and/or dump coating material.
Nordson Airless Nozzle Tester
Instruction Sheet P/N Nordson Airless Nozzle Tester. Introduction The Nordson airless nozzle tester is used to test the flow rate of flanged airless nozzles. The results of the tests can be used to determine
Solenoid Valve Installation Kit
Instruction Sheet P/N 7 5A Solenoid Valve Installation Kit WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related
H2O-C14 AAA FINE FINISH SERIES PUMP OUTFIT
PRODUCT INFORMATION H2O-C14 AAA FINE FINISH SERIES PUMP OUTFIT The H2O-C14 AAA pump system is an air assisted airless unit which combines airless and conventional or HVLP air atomization technologies to
B14 AAA FINE FINISH SERIES PUMP OUTFIT
PRODUCT INFORMATION B14 AAA FINE FINISH SERIES PUMP OUTFIT The B14 AAA pump system is an air assisted airless unit which combines airless and conventional or HVLP air atomization technologies to produce
Fast-Flo Pump INSTRUCTIONS-PARTS LIST. Table of Contents 1:1 RATIO
INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. First choice when quality counts. 07 7 Rev. Z Supersedes W Includes Rev. Y changes
RA-20 Paint/Solvent/Dump Valve
Instruction Sheet P/N 74B0 RA-0 Paint/Solvent/Dump Valve Description The paint/solvent valve is a normally closed valve used to trigger coating material. The valve may be used alone to actuate paint or
Fluidizing Pickup Tube Kits
Instruction Sheet P/N 303787-02 Introduction The fluidizing pickup tube kit retrofits your existing mobile powder system with fluidizing air. It injects fluidizing air at the pickup tube inlet with minimal
8. Illustrated Parts Lists
Hydraulics B 1-45 8. Illustrated Parts Lists To order parts, call the Nordson Customer Service Center or your local Nordson representative. Use these five-column parts lists, and the accompanying illustrations,
DISPLACEMENT PUMP INSTRUCTIONS-PARTS LIST Rev. K. Model , Series A Model , Series B Model , Series A
INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. DISPLACEMENT PUMP 308190 Rev. K 3000 psi (210 bar) MAXIMUM WORKING PRESSURE Model
Page 1 of 19. Part# /10/2006
Part# 1002733-01 10/10/2006 This manual contains important information concerning the installation and operation of the gun washers listed above. Read manual thoroughly and keep for future reference INSTRUCTIONS
Parts. Part B, Section 5. Model 3500 Voltage 1, 2. Manifold 6-Port (B or C) 2-Port (S or T) Issued 11/00 B5EN-05-[3-PARTS]-6
Part B, Section 5 Model 500 Voltage, Pump Piston (E) Manifold -Port (B or C) -Port (S or T) Control MultiScan (M) 000Nordson Corporation -000 Issued /00 B 5-0 -000 Issued /00 000 Nordson Corporation B
Module. Table of Contents. Section 9. Module NOTE: This section applies to applicators with CF200PAD right-angle modules.
9-1 Section 9 NOTE: This section applies to applicators with CF200PAD right-angle modules. Table of Contents.................................................... 9-1 Introduction................................................
8. Illustrated Parts Lists
Hydraulics B 1-41 8. Illustrated Parts Lists To order parts, call the Nordson Customer Service Center or your local Nordson representative. Use these five-column parts lists, and the accompanying illustrations,
A CAUTION: The kit should not be fitted on Series 3800 or 3900
Series 3000 O:l Pump Installation Kit Instructions 6-52 Page O:l SINGLE ACTING PUMP INSTALLATION (P/N 3 598) KIT INTRODUCTION. The O:l Single Acting Pump Installation Kit gives you all the necessary items
8. Illustrated Parts Lists
Hydraulics B 1-43 8. Illustrated Parts Lists To order parts, call the Nordson Customer Service Center or your local Nordson representative. Use these five-column parts lists, and the accompanying illustrations,
Colt Series C400, C500
Colt Series C400, C500 RP/IS-A-C400/C500 C400 OSY Reduced Pressure Zone Assemblies Reduced Pressure Detector Assemblies Sizes: 2 1 2" 10" (65 250mm) Installation Service Repair Kits Maintenance For other
Trilogy Air Spray and LVLP Automatic Spray Guns
Trilogy Air Spray and LVLP Automatic Spray Guns Customer Product Manual Part 1601058-03 Issued 3/14 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800)
0-500 PSI Soft Seat Fluid Pressure Regulator
Instruction Sheet P/N 0953A Description The Nordson 0-500 psi soft seat fluid pressure regulator is designed for use with nonabrasive liquid coatings. The regulator body is constructed of stainless steel
SP30 6:1 Piston Pump. Installation and Maintenance Instructions. Part D NORDSON CORPORATION AMHERST, OHIO USA
Installation and Maintenance Instructions Part NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments and inquiries about its products. Address all correspondence
NRPS-100 Rotary Sieve
NRPS-100 Rotary Sieve Customer Product Manual Part For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local Nordson representative.
Maintenance. Part A, Section 5. This section covers the following unit configurations.
Part A, Section 5 This section covers the following unit configurations. Model 3100V 3400V 3830V 3860V 3890V 3930V Voltage 1, 2 Pump AC Gear (K or L) Manifold 4-Port (J)) Control Vista Standard (V) Vista
Module. Table of Contents. Section 9. Module NOTE: This section applies to applicators with MB200 modules.
9- Section 9 NOTE: This section applies to applicators with MB200 modules. Table of Contents.................................................... 9- Introduction................................................
CAB TILT HYDRAULIC SYSTEM
OPERATION, MAINTENANCE and SERVICE INSTRUCTIONS CAB TILT HYDRAULIC SYSTEM WITH POWER-PACKER PUMP, CYLINDERS and LATCHES A division of Actuant Corporation 1-800-745-4142 1 www.powerpackerus.com Notice The
Installation and Service Instructions
FLX35-6 & FLX55-6 Series Rotary Sprinklers Installation and Service Instructions Introduction The FLX35-6 and FLX55-6 series full and part circle rotary sprinklers are designed specifically for golf course
INSTRUCTIONS. US Patent Pending HVLP Turbine Guns
INSTRUCTIONS 309317 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Rev. A US Patent Pending HVLP Turbine Guns 10 psi (0.07 MPa,.7 bar) Maximum Inlet
Air Spray Proportioning Valve
Instruction Sheet P/N Air Spray Proportioning Valve. Installation The air spray proportioning valve provides close regulation of air spray characteristics for air spray versions of the Pro-Flo dispensing
Module. Section 9. NOTE: This section applies to applicators with CC200 modules B Issued 6/01. Manual 42-CF200-CM-01
Section 9 NOTE: This section applies to applicators with CC200 modules. 9-0 Table of Contents i Table of Contents Section 9 1. Introduction............................................... 9-1 2. Specifications.............................................
Blow Off Valve Retrofit Kit
Instruction Sheet P/N 37 56C low Off Valve Retrofit Kit WRNING: llow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation..
AMIAD Automatic Filters
1. Model EBS AMIAD Automatic Filters Maintenance Guidelines General inspection In order to check the proper operation of the filter, close the low-pressure 1/4" valve to the pressure differential switch
Val-Matic Air / Oil Hydraulic Panel Pump Control System. Operation, Maintenance and Installation Manual
Manual No. 5AOP-OM1-2 Val-Matic Air / Oil Hydraulic Panel Pump Control System Operation, Maintenance and Installation Manual INTRODUCTION... 1 RECEIVING AND STORAGE... 1 DESCRIPTION OF OPERATION... 1 INSTALLATION...
SPEEFLO. PowrTex 300dd / 600dd Texture Sprayers. Owner s Manual For professional use only. Do not use this equipment before reading this manual!
Owner s Manual For professional use only Do not use this equipment before reading this manual! SPEEFLO PowrTex 300dd / 600dd Texture Sprayers These sprayers are for use with water-based materials only!
Engine Oil, Cooling System
Engine Oil, Cooling System OIL FILTER 6. Refill the engine with the recommended oil. Engine oil change capacity (including filter): () 4.4 US qt (4.2 ) () 4.5 US qt (4.3 ) 7. Replace the engine oil fill
Preventive Maintenance for Pail Melters
Instruction Sheet P/N Preventive Maintenance for Pail Melters 1. Introduction These procedures are recommended in addition to the standard preventive maintenance. Use them to keep yourvista controlled
CONTROLS. Bray Pneumatic Actuators & Accessories. Technical Manual. A Division of BRAY INTERNATIONAL, Inc.
CONTROLS A Division of BRAY INTERNATIONAL, Inc. Bray Pneumatic Actuators & Accessories Technical Manual TM-056 Pneumatic Actuator - 08//00 Bray Pneumatic Actuators & Accessories Technical Manual - Table
Optimiser 2K HVLP Two Component Adhesive Spray Gun
INSTRUCTIONS-PARTS LIST 308 34 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. First choice when quality counts. Rev. G Supersedes F Optimiser 2K HVLP
Putty 2000 Chop Check Start-Up Instructions
Putty 2000 Chop Check Start-Up Instructions MAGNUM VENUS PRODUCTS Putty 2000 Chop Check Start-Up Instructions START-UP INSTRUCTIONS NOTE: The regulators marked pump, air lift and ram extraction should
Post Driver Attachment
Attachment (Shown with Optional Power Cell Rotator) Models - 600, 850 Safety Instructions This safety alert symbol indicates important safety messages in this manual. When you see this symbol, carefully
CARCO ES-370 AKT Spray Gun The ES-370 AKT Automatic Spray Gun is a production spray gun designed to apply a wide range of marking fluids, including Carco pigmented and dye type marking fluids. CONNECTIONS:
ETP-5G & ETP-10G ECO-TECH PLUS GAS CONVECTION STEAMER PARTS AND SERVICE MANUAL
ETP-5G & ETP-10G ECO-TECH PLUS GAS CONVECTION STEAMER PARTS AND SERVICE MANUAL EFFECTIVE JANUARY 10, 2018 Superseding All Previous Parts Lists. The Company reserves the right to make substitution in the
PRO Auto Xs Air Spray Gun
Instructions/Parts List ELECTROSTATIC, FOR WATERBORNE COATINGS PRO Auto Xs Air Spray Gun 309457G EN Part No. 244591, Series A 100 psi (0.7 MPa, 7 bar) Maximum Air Inlet Pressure 100 psi (0.7 MPa, 7 bar)
EP-2 Three-Piston Pump
EP- Three-Piston Pump Customer Product Manual Issued 0/ For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) -99 or contact your local Nordson representative.
Baumann Mikroseal Control Valve
Instruction Manual 81000 Valve Baumann 81000 Mikroseal Control Valve Contents Introduction... 1 Scope of Manual... 1 Safety Precautions... 2 Maintenance... 3 Installation... 3 Air Piping... 4 Flow Direction...
Pressure Relief Valve Maintenance Manual
Technical Manual 1098T Pressure Relief Valve Maintenance Manual Farris Engineering Division of Curtiss-Wright Flow Control Corporation TABLE OF CONTENTS - Manual Revision 0 Introduction & Safety Tips...
Solenoid Operated Block Valves A2800 Series
Solenoid Operated Block Valves A2800 Series Installation and Parts Liquid Controls An IDEX Fluid & Metering Business Installation: M400-40 Table of Contents Introduction Safety Procedures... 3 A2800 Series
Fisher D2T FloPro Control Valve
Instruction Manual D2T FloPro Valve Fisher D2T FloPro Control Valve Contents Introduction... 1 Scope of Manual... 1 Description... 1 Educational Services... 2 Specifications... 3 Installation... 3 Setting
OPERATOR S MANUAL X INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
OPERATOR S MANUAL 651616-X INCLUDING: OPERATION, INSTALLATION & MAINTENANCE INCLUDE MANUALS: 66516 X FOLLOWER PLATE (PN 97999 854), 67195 X FOLLOWER PLATE (PN 97999 841) & S 635 GENERAL INFORMATION (PN
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical 17 Engine-Lubrication system (Page GR-17)
17 Engine-Lubrication system (Page GR-17) Lubrication system components, removing and installing Oil pressure and oil pressure switch, checking Sump, removing and installing Valve gear, servicing (Page
TS1251 PRESSURE DISPENSER USER'S MANUAL
TS1251 PRESSURE DISPENSER USER'S MANUAL TABLE OF CONTENTS SECTION DESCRIPTION PAGE NUMBER 1.0 CAUTIONS AND WARNINGS... 3 2.0 INTRODUCTION... 4 3.0 DESCRIPTION... 4 & 5 4.0 SET UP AND INSTALLATION... 6
Introduction. Installation. Maintenance. Bill of Materials
Table of Contents Introduction Specitications... 3 Operation... 4 Installation New Installations... 6 Retrofit Installations... 6 Flow Control Switch... 7 Dimensions... 8 E-7 Valve... 28 E-7 Valve with
Owner's Manual. Model: ( ) (150 Gallon, 5.5 HP Skid Sprayer) Technical Specifications. General Information. Warranty/Parts/Service
Owner's Manual Model: -0 (00) (0 Gallon,. HP Skid Sprayer) Technical Specifications General Information Thank you for purchasing this product. The purpose of this manual is to assist you in operating and
Super T QR20 INSTRUCTIONS GENERAL RULES
INSTRUCTIONS GENERAL RULES 1. Where specified, assemble and disassemble the shock absorption system using the MARZOCCHI special tools only. 2. On reassembling the suspension system, always use new seals.
Kinetix Electrostatic Spray Gun Automatic Version 60 kv Air Spray and KVLP Waterborne
Kinetix Electrostatic Spray Gun Automatic Version 60 kv Air Spray and KVLP Waterborne Customer Product Manual Issued 8/08 For parts and technical support, call the Industrial Coating Systems Customer Support
OPERATOR S CARD. Select Series H-440 Hot Melt Dispensing Guns. Safety. Description. Nordson Corporation P/N D
Nordson Corporation OPERATOR S CARD P/N 321 198D Select Series H-440 Hot Melt Dispensing Guns Safety WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions
USE and MAINTENANCE INSTRUCTION MANUAL W-300 W-300 WB LPH-300 GRAVITY. SPRAY GUN Series. en it fr es pt de se
USE and MAINTENANCE INSTRUCTION MANUAL W-300 W-300 WB LPH-300 GRAVITY SPRAY GUN Series en it fr es pt de se TECHNICAL DATA High T.E.C. series Nozzle_Needle set Combination W-300 WB W-300 W-300-081G 0.8
OPERATION MANUAL NT50 NOMAD TRANS-FLO AIR-OPERATED DOUBLE DIAPHRAGM PUMPS. A JDA Global Company. 7/11 rev. 1
OPERATION MANUAL NT50 NOMAD TRANS-FLO AIR-OPERATED DOUBLE DIAPHRAGM PUMPS A JDA Global Company 7/11 rev. 1 CAUTION SAFETY POINTS TEMPERATURE LIMITS: Neoprene -17.8 C to 93.3 C 0 F to 200 F Buna-N -12.2
ICS Integrated Cleaning System. Rechargeable Battery
ICS 8900 Integrated Cleaning System Rechargeable Battery THANK YOU FOR CHOOSING OUR PRODUCTS Hydro Systems manufactures quality chemical proportioners. Please use this equipment carefully and observe all
AMIAD Automatic Filters
AMIAD Automatic Filters Filtomat M100-6800 Series Models: M104XLP, M106XLP, M108LP, M110P Hydraulically-Controlled Serial number: Order number: Catalog number: Filtration degree: Tested by: Installation,
Models CHASSIS LUBE ELECTRIC GREASE PUMP Series "C" - Q3. MAY FORM Section
Models 94822 CHASSIS LUBE ELECTRIC GREASE PUMP Series "C" - Q3 MAY - 2004 FORM 403468 Section Page - 14B 13.00" (330 mm) 17.72" (450 mm).35" (9 mm) Mounting Holes 4.72" (120 mm) 9.84" (250 mm) Figure 1
OWNERS MANUAL GM C4500/C5500 4X4 DANA MODEL S135 REAR AXLE 2005-NEWER MODELS LINK MFG. PART NO. 8M PROUDLY INSTALLED BY : COMPANY :
OWNERS MANUAL GM C4500/C5500 4X4 DANA MODEL S135 REAR AXLE 2005-NEWER MODELS LINK MFG. PART NO. 8M000060 Link Mfg. Ltd. 223 15th St. N.E. Sioux Center, IA USA 51250-2120 (712) 722-4874 Fax (712) 722-4876
Air Operated Diaphragm Pumps
Instructions Air Operated Diaphragm Pumps 30898ZAC For fluid transfer applications. For professional use only. Only models marked with (*) are approved for use in European explosive atmosphere locations.
Moniteur INSTALLATION & OPERATING INSTRUCTIONS. SERIES 40 Positioners. Installation and Operating Instructions Series 40 Positioners.
INSTALLATION & OPERATING INSTRUCTIONS SERIES 40 Positioners Form IO2-0406 Description of Device Moniteur's Series 40 pneumatic (3-15psi) and electropneumatic (4-20mA) positioners are advanced control devices
TECHNICAL DATA 1-1/2 (dn40)
July 1, 2011 Deluge Valves 209a DESCRIPTION The Viking Model E-3 1-1/2 Deluge Valve is a quick-opening, differential type flood valve with a rolling diaphragm clapper. The deluge valve is used to control
t EVAPORATOR PRESSURE REGULATING VALVES
CATALOG 201 Page 63 t EVAPORATOR PRESSURE REGULATING VALVES (S)ORIT-12, -15 and -20 Features n High side pilot for improved temperature control and low P operation n Adjustable n Optional solenoid stop
SHORTENING FILTER. Operating Instructions INSPECT CARTON SPECIFICATIONS PARTS. MODEL NO'S 102 & 107 CE Series
Operating Instructions SHORTENING FILTER INSPECT CARTON MODEL NO'S 102 & 107 CE Series Remove product from carton... If damaged : Notify carrier Save carton and packing material Contact your Dealer, Distributor
OWNER S MANUAL REMOTE CONTROL, DUAL HEAD FOGGING SYSTEMS
OWNER S MANUAL Sentinel II 5500 REMOTE CONTROL, DUAL HEAD FOGGING SYSTEMS Read all instructions carefully before starting the installation. Save this manual for future use. 2 OWNER S MANUAL SAFETY Always
Fisher 1051 and 1052 Style H and J Sizes 40, 60 and 70 Rotary Actuators
Instruction Manual 1051 and 1052 H & J Actuators Fisher 1051 and 1052 Style H and J Sizes 40, 60 and 70 Rotary Actuators Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications...
Mounting and Operating Instructions EB 8222 EN. Type 3310/AT and Type 3310/3278 Pneumatic Control Valves. Type 3310 Segmented Ball Valve
Type 3310/AT and Type 3310/3278 Pneumatic Control Valves Type 3310 Segmented Ball Valve Fig. 1 Type 3310/3278 with positioner Fig. 2 Type 3310/AT Mounting and Operating Instructions EB 8222 EN Edition
Assembly / Operation Instructions / Parts
Assembly / Operation Instructions / Parts TSU SKU# 0 VENDOR# ATV 0 CL GALLON DELUXE ATV SPRAYER - NOZZLE Polyethylene Tank Volt Diaphram Pump.0 G.P.M. Lever Handgun Ft. of / Hose (handgun) Pressure Gauge
Sure Coat 90 Degree Spray Extension
Instruction Sheet P/N 076A Sure Coat 90 Degree Spray Extension Description The 90 Degree Spray Extension is used on Sure Coat Automatic Powder Spray Guns. It allows powder to be sprayed at right angles
A system of lubricant dispensing devices (oil or grease) connected by piping to a central pumping unit that is operated automatically or manually.
Air/Oil Systems: A lubrication system in which small measured quantities of oil are introduced into an air/oil mixing device which is connected to a lube line that terminates at a bearing, or other lubrication
Welker Sampler. Installation, Operation, & Maintenance Manual. Model GSS-4HP
Installation, Operation, & Maintenance Manual Welker Sampler Model GSS-4HP The information in this manual has been carefully checked for accuracy and is intended to be used as a guide to operations. Correct
Form No Parts List for: MODEL B ELECTRIC HYDRAULIC PUMP. Maximum Capacity: 10,000 PSI PE55TWP-IBT-115. Sheet No. 1 of 8
Parts List for: Form No. 1000457 PE55TWP-IBT-115 MODEL B ELECTRIC HYDRAULIC PUMP Maximum Capacity: 10,000 PSI 1 2 3 7 SPX Hydraulic Technologies, Rockford, IL 61109 USA www.powerteam.com Made in USA 309219Rev7
Distributed By: M&M Control Service, Inc Product Product Code Technical Instructions Page #
Table of Contents Product Product Code Technical Instructions Page # Pneumatic Air Station Equipment 201/656/908 155-005/049/086/137P25 H-3 Pressure Gauges GA142AP 155-025P25 H-7 External Restrictors 184
INSTRUCTIONS This manual contains important warnings and information. READ AND RETAIN FOR REFERENCE
INSTRUCTIONS 307 378 INSTRUCTIONS This manual contains important warnings and information. READ AND RETAIN FOR REFERENCE Rev. H Supersedes G Model 600 Air Spray Gun 100 psi (7 bar) Maximum Working Fluid
Calibration and Switching Module. User s Manual. A Swagelok Pre-Engineered. Subsystem. Pre-engineered subsystems available in weeks, not months.
Calibration and Switching Module User s Manual A Swagelok Pre-Engineered Subsystem Pre-engineered subsystems available in weeks, not months. Field-tested design ensures optimum system performance. Contents
To ensure proper installation, digital pictures with contact information to before startup.
Check List for Optimal Filter Performance? There should be no back-pressure on the flush line. A 1 valve should have a 2 waste line, and 2 valve should have a 3 waste line. Do not use rubber hosing or
LEAD FREE * LFF113RFP Flood Protection Shut Down Valve
Technical Bulletin TB-ACV-LFF11RFP LEAD FREE * LFF11RFP Flood Protection Shut Down Valve Installed upstream of Reduced Zone Backflow Preventer. Normally Open Valve - Closes when continuous discharge from
VA-908x Series Electric Rotary Actuators for Two-Position and Modulating Service
VA-908x Series Electric Rotary Actuators for Two-Position and Modulating Service Installation Instructions VA-908x Code No. LIT-12011566 Issued August 24, 2009 Applications The VA-908x Series Electric
Service Handbook. High-Pressure Washer Pump
Pump 629 9/28/01 3:22 PM Page 1 Service Handbook High-Pressure Washer Pump 3.532-629.0 10.00 Pump 629 9/28/01 3:22 PM Page 2 Pump 629 9/28/01 3:22 PM Page 3 TROUBLESHOOTING OVERVIEW How to Use This Manual
Installation Instructions
Installation Instructions Individual Built-In Wall Shower with Concealed Supplies Table of Contents Pre-Installation Information...2...3 Repair parts...4 Metering Valve Troubleshooting...5 Cleaning and
WORKHORSE PSE. Assembly / Operation Instructions / Parts
WORKHORSE S P R A Y E R S Assembly / Operation Instructions / Parts by PSE, a Division of Green Leaf, Inc ATV BL DELUXE ATV BOOMLESS SPRAYER Polyethylene Tank Volt Diaphram Pump.0 G.P.M. or.0 G.P.M. Lever
Series 72 Electri-SAFE On/Off Operation Including CLC Option Installation, Operation and Maintenance Instructions
WCAIM2049 (Part 18960) Series 72 Electri-SAFE On/Off Operation Including CLC Option Installation, Operation and Maintenance Instructions Series 72 actuators are electro-hydraulic quarterturn valve actuators.
ETF-600 Sensor Operated Lavatory Faucet
INSTALLATION INSTRUCTIONS OPTIMA SYSTEMS SENSOR OPERATED LAVATORY FAUCET ETF-600 I.I. Code No. 0816318 ETF-600 Sensor Operated Lavatory Faucet Includes Instructions for Installation of Optional Back Checks
PLUNGER PUMP SERVICE MANUAL
PLUNGER PUMP SERVICE MANUAL INSTALLATION AND START-UP INFORMATION Optimum performance of the pump is dependant upon the entire liquid system and will be obtained only with the proper selection, installation
1991 TRANSMISSION SERVICING Automatic Transmission. Mitsubishi: Eclipse, Galant, Mirage, Montero, Pickup, Precis, 3000GT
Article Text ARTICLE BEGINNING 1991 TRANSMISSION SERVICING Automatic Transmission Mitsubishi: Eclipse, Galant, Mirage, Montero, Pickup, Precis, 3000GT IDENTIFICATION MITSUBISHI AUTOMATIC TRANSMISSION APPLICATIONS
DP3 Pump. 3:1, Air-operated, Oil. General. Operation. Technical Data. Installation R0 10/09. 35a 35b 35c
DP3 Pump 3:1, Air-operated, Oil General The DP3 Pump is a compressed air-operated piston reciprocating medium pressure pump. Suitable for medium flow transfer of high viscosity lubricants and for oil delivery
Installation Instructions for Series 3100V Low Level Indicator
Instruction Sheet P/N Installation Instructions for Series 3100V Low Level Indicator WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document
Model: ATVTS-60-12V 60 Gallon Trailer Sprayer W/7 Nozzle Boom ASSEMBLY / OPERATION INSTRUCTIONS / PARTS
5301192 Model: ATVTS-60-12V 60 Gallon Trailer Sprayer W/7 Nozzle Boom ASSEMBLY / OPERATION INSTRUCTIONS / PARTS ASSEMBLY INSTRUCTIONS The sprayer is assembled except for the pressure gauge, axle, wheels
JARVIS. Model 30CL-ABC Beef Aitch Bone Cutter
Model 30CL-ABC Beef Aitch Bone Cutter EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page 30CL--ABC Aitch Bone Cutter Front Entry... 4025102 Rear Entry... 4025111 Hydraulic Power Unit... 4027266
Quick Opening Closure Operating Instructions
Quick Opening Closure Operating Instructions To prevent SERIOUS INJURY and PROPERTY DAMAGE, you should read, understand and follow these Operating Instructions. Keep for future reference. 1 Safety Information
Section 5. Maintenance. Risk of Burns. Relieving Pressure. Important when Using Cleaning Agents. Maintenance 5-1
5-1 Section 5 WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation. NOTE: is an important
Baumann Sanitary Diaphragm Angle and Inline Control Valve
Instruction Manual 84000 Valve Baumann 84000 Sanitary Diaphragm Angle and Inline Control Valve Contents Introduction... 1 Scope of Manual... 1 Safety Precautions... 2 Maintenance... 2 Flow Direction...
Optima ETF-600/ETF-610
Optima ETF-600/ETF-610 4B ETF-610 1C 4A 5 6 7 7 6 ETF-600 1A 1C PARTS LIST ETF-600 AND ETF-610 FAUCETS Item No. Code No. Part No. Description 1A. 065086 ETF-54-A Faucet and Sensor Assembly (ETF-600). 065117
CHEM-TEX POWER MAX 25 GOLD EDITION TRUCK MOUNT MANUAL
CHEM-TEX POWER MAX 25 GOLD EDITION TRUCK MOUNT MANUAL Congratulations On your purchase of a Power Max 25 Gold Edition Truck mount. The Power Max 25 Gold Edition are designed for the professional cleaning
KJ Motor/Pump Assembly. Jetter. Printed in U.S.A. Ridge Tool Company/Elyria, Ohio, U.S.A.
KJ-000 Motor/Pump Assembly NOTE: Order parts by Number Only. 0 0 0 Gasoline Engine, Hp Manual Start 0 Gasoline Engine, Hp Electric Start Decal, Warning 0 Decal, Fuel Warning Decal, Model. KJ-000 Key, /
1 CONDIMENT DISPENSING SYSTEMS MODELS MCD-1 & MCD-2
1 CONDIMENT DISPENSING SYSTEMS MODELS MCD-1 & MCD-2 THIS EQUIPMENT CHAPTER SHOULD BE INSERTED IN THE EQUIPMENT MANUAL MANUFACTURED FOR McDONALD S BY PERFECTION EQUIPMENT, INC. 4259 LEE AVENUE GURNEE, ILLINOIS
Electric Airless Sprayers Operating Instructions
Electric Airless Sprayers Operating Instructions 309365 Rev. A 3000 psi (210 bar, 21 MPa) Maximum Working Pressure How To Perform: Component Identification....... 3 Setup........................... 4 Startup..........................
Airsweep Installation & Maintenance Manual. Airsweep Models VA-06 VA-12 VA-51 SECTION THREE SOLENOID VALVES
Airsweep Installation & Maintenance Manual Airsweep Models VA-06 VA-12 VA-51 SECTION THREE SOLENOID VALVES Model DV1251 / Conduit & DIN Connection Model DV06 / RDV / MCA / RCA Diaphragm Valves Goyen Model