PS AMA F (a) 0411 ( )

Transcription

1 PS AMA F (a) 0411 ( )

2 Table of Contents Body Style Versus Application Flow Coefficients (Cv) Versus Travel Shut-Off P Ratings Sizing Reference and Load Sizing Calculations Actuator Specification Factory Default Settings Actuator Orientations Dimensions and Weights Typical Construction Configurations Type 50 Three-Way Mixing Valve Stem Wipers provide outstanding packing protection. Heavy Bolted Bonnet Construction provides added durability and easy maintenance. Large Guiding Surfaces ensure smooth operation and stem stability. Skirt Guided Plug Assembly provides stability and precision linear flow characteristic. Large Internal Flow Patterns maximize CV capacities. Greater flow with smaller sizes reduces cost. Lower Unit disassembles for easy trim replacement or debris removal. TFE V-Ring Packing Spring-Loaded Stem lubricator is available as an option, but is not required for standard packing sets. Description: Warren Controls AMA Heavy Globe Control Valves feature rugged high capacity bodies of steel, or stainless steel with a variety of trim materials and port sizes. The linear plugs in the 3- way valves provide excellent modulating control of a wide variety of fluids. The AMA Series is ideally suited where value and long life are important objectives for applications including but not limited to the Chemical, District Energy, Food & Beverage, General Service, Marine, Power, and Refining industries with temperatures from -20 to 550ºF, severe service, high pressure drops, and corrosive fluids.

3 AmurAct Overview The AmurAct Actuator is a revolutionary product in both function and design with best-in-class performance at a price point previously ignored by other manufacturers. While when configured the valve can fully open from closed in about 8 seconds, the actual response time to a required heavy load change from a normal flow condition is only 2 3 seconds, on par with pneumatically actuated products. The AmurAct linkage has tremendous torque as it approaches closure allowing for increased close off pressure even on larger valves. Fail-Safe is of course included with Enerdive*. The patented Enerdrive System. The modern, electronic replacement for antiquated spring return actuator is a super capacitive fail-safe return system. * Enerdrive or the Enerdrive System is both a patent and trademark of National Environmental Products, Ltd. Since its introduction, Enerdrive has proven its versatility and dependability. As a system that is fully incorporated into the PC board for both low and line voltage service, the power generated and stored in its capacitors will drive the control valve at full rated torque to its safety position. It is 100% operational with the resumption of power. Each unit may be manually positioned with the clutch override that is standard on each actuator. Most importantly, the final fail position, either normally open or normally closed may be chosen at any time either before or after installation with the flick of a dip switch. Corrosion-resistant stainless steel safety enclosure. Base and linkage also constructed from corrosion-resistant stainless steel....the actual response time to a required heavy load change from a normal flow condition is only 2 3 seconds! Strong, long-life sintered bronze pre-lubricated bearings at pivot points. Articulated stem connection to extend valve packing life. Strong and compact... a single actuation package fits and operates a wide selection of valves. Laboratory & field tested for strength and durability. Optional configuration for higher-temperature applications AmurAct Fast Electric Actuator

4 Body Style Versus Application 3-Way Valves (Control of Liquids) Type 50 Three-Way Mixing Valve This valve has two inlets and one outlet, and is the simplest solution for mixing or bypass applications with an ANSI Class IV leakage rating. In normal applications the inlet pressures are near equal and control is possible from 5% to 95% of travel with inlet pressures up to 300 PSI. In the 1/2 through 2 inch sizes, the flow can be reversed for diverting if this port configuration is desirable. Sizes: 1/2, 3/4, 1, 1-1/2, 2 inch Body: WCB Steel or CF8M Stainless Steel 150LB Flange or 300LB Flange Trim: Linear, 316 Stainless Steel Packing: TFE V-Ring, Spring Loaded ( +32 to 450 F) TFE V-Ring Spring Loaded w/extension Bonnet (-20 to 550 F) Temperature: -20 to 550 F (150 or 300 FLG) Rangeability: 30:1 (sizes 1/2 thru 2) Flow Coefficients (Cv) Versus Travel 3-Way Valves (Control of Liquids) Valve Type 50 Flow Coefficients (Cv) Three-Way Mixing/Diverting Valve Valve Trim Trim Port Travel Size (IN) Style Size(IN) Size 100% 1/2 Linear Full SR SR /4 Linear Full SR SR SR Linear Full SR SR SR /2 Linear Full Linear Full 40.0 In the 1/2 through 2 inch sizes, the flow can be reversed for diverting if this port configuration is desirable. Stem Down Stem Up Upper Port Flow Flow Lower Port The upper port opens and the lower port closes Body Pressure-Temperature Ratings: Temperature (F) 150 FLG 300 FLG 150 FLG 300 FLG Steel Steel St Steel St Steel -20 To Pressure ratings are PSIG Common Port For applications below 32º consult factory Upper Port Flow Flow Lower Port The upper port closes and the lower port opens Common Port Type 50 Mixing % CV TYPICAL FLOW CURVE % TRAVEL Agency Approvals Agency Approvals UPPER LOWER COMBINED Flowing Differential Trim Materials Pressure Limit 316 Stainless Steel 100 PSID For additional applications, and/or products call: or visit: PS AMA F (a) 0411 ( )

5 AMA Shut-Off P Rating AMA Series Type 50 lower seat Shutoff Motor Choices UPPER seat Shutoff Motor Choices sizes Seat Diameter F3 & F5 F4 & F6 F3 & F5 F4 & F6 1/2-3/ / / / Shut-Off P Ratings NOTE: 1. For maximum trim life observe maximum sustained flowing differential pressure trim limits. See page 3 2. Under power fail conditions the valve leakage rate is at the next lower ANSI leakage class. Sizing Reference Load Sizing Calculations Steam Table Steam Temp. Temp. Sensible Latent Total Pressure F C Heat Heat Heat PSIG BTU/Lb. BTU/Lb. BTU/Lb Rectangular Tank Capacity in Gallons Gallons = or Height x Width x Length (inches) 230 Gallons = H x W x L (Ft.) x 7.5 Circular Tank Storage Capacity in Gallons Storage = 6D 2 x L (Gallons) Where: D = Tank Diameter in Feet L = Length in Feet Heating Water with Steam Quick Method GPM Lbs./Hr. = x T 2 Accurate Method GPM x 500 x T Lbs./Hr. = h fg Heating or Cooling Water with Water GPM 1 = GPM 2 x Heating or Cooling Water GPM = F water 2 temp. rise or drop F water 1 temp. rise or drop BTU / Hr. ( F water temp. rise or drop ) x 500 Heating Oil with Steam Lbs./Hr. = GPM 4 x ( F oil temp. rise) Conversion Factors 1 Lb. Steam / Hr. = 1000 BTU / Hr. 1 Cubic Meter = 264 U.S. Gallons 1 Cubic Foot Water = 62.4 Lbs. 1 PSI = 2.04 Inches of Mercury 1 PSI = 2.3 Feet of Water 1 PSI = 27.7 Inches of Water 1 U.S. Gallon Water = 231 Cubic Inches 1 U.S. Gallon Water = 8.33 Lbs. Heating Air with Water CFM x ( F air temp. rise) GPM = 2.16 x 1000 x ( F water temp. drop) Heating Liquids with Steam Lbs./Hr. = GPM x 60 x Cp x W h fg Heating Liquids in Steam Jacketed Kettles Gallons x Cp x S x 8.33 Lbs./Hr. = h fg x t General Liquid Heating Lbs./Hr. = W x Cp h f g x t x T Heating Air with Steam Lbs./Hr. = CFM x T 900 Glossary of Terms t = Time in Hours Cp = Specific Heat of Liquid S = Specific Gravity of Fluid W = Weight in Lbs. T = Temperature Rise or Fall in F h fg = Latent Heat of Steam x T x T 2600 Emrick Blvd., Bethlehem, PA Tel: or Fax:

6 Actuator Specifications & Factory Default Settings AmurAct Electric Motor Actuator Specifications: Control Signal: Control Action: Output: Power Supply: Power Consumption: Timing: Feedback Signal: Fail Safe: Calibration: Analog 4-20 madc (Factory Default), or 2-10 Vdc (Call Factory at for other options) 2-Way Valves, Increasing Signal Opens Valve (Factory Default) Reversible, Dip-Switch Selectable 3-Way Valves, Increasing Signal Raises Stem (Opening the L port and Closing the U port, Factory Default) Reversible, Dip-Switch Selectable Linear Stem Lift (Factory Default), Non-linear Stem Lift Dip-Switch Selectable 120 (110 to 130) VAC 50/60 Hz, 24 VAC, or 30 Vdc (F3 & F4), 220 (220 to 250) VAC 50/60 Hz (F5 & F6) 50VA Peak, 30VA Normal Operation 12 Seconds Typical 4-20 madc (Factory Default),or 2-10 Vdc, Dip-Switch Selectable Yes (Enerdrive Failsafe System, Stem Down (Factory Default), or Stem Up, Dip-Switch Selectable) Push Button Auto-Calibration Torque: 120 in-lbs (F3 & F5), 240 in-lbs (F4 & F6) Motor: Motor Rating: Connections: Wiring: Locations: Temperature Limits: Relative Humidity: Brushless DC 100% Duty Cycle Screw Terminal Block 18 AWG Minimum No Rating (Standard), NEMA 4X (Optional with LS Standard Linkage Orientation) Ambient... 0 o F to 150 o F 5 to 95% Non-Condensing Weight: 5 Lbs (F3 & F5), 8 Lbs (F4 & F6) Approvals: UL pending, CE, c CSA us, AMURACT FACTORY DEFAULT SETTINGS Unless a purchase order specifically requests it to be configured differently, an AmurAct control valve will accept a 4-20 madc input signal, provide 4-20 ma feedback, will fail shut (lower port shut for 3-way valves) upon loss of either operating power or input signal or both, and will have linear stem lift. Linear Stem Lift vs. Non-linear Stem Lift Linear stem lift is the factory default dipswitch selection. Linear stem lift means the stem position is linear with respect to the input signal. For example if the valve is closed with a 0% input signal, the valve will be at 25% Stroke with a 25% input signal, at 50% Stroke with a 50% input signal, at 75% Stroke with a 75% input signal, and at 100% Stroke with a 100% input signal. Linear stem lift preserves the inherent flow characteristic of the valve. When non-linear stem lift is selected the actuator has an ever gain changing stroke curve that accelerates in the last half of the stroke and is relatively slow on startup. Extreme gain changes as present in the Non- linear configuration are difficult for a control system to manage. If an application s turndown requirements are only 3:1 to 5:1 for example such that a valve could be sized to only operate from 50% to 100% of stroke, some level of speed of response can be achieved in the Non-linear configuration. Otherwise, in all other circumstances, the Linear Stem Lift (factory default) will be the desired setting. In either case, correct control valve sizing is critical to good operation. NOTES: 1. Linkage Model LS at factory is aligned with the pipe center line. It is specified when line media are below 250 deg. F., or 340 deg. F. when the valve body is insulated. 2. Linkage Model LE must be installed perpendicular to the pipe center line. It is specified when line media flowing through un-insulated valves exceed 250 deg. F., or 340 deg. F. through insulated valves. The 180-degree offset anti-rotation tailpiece is integral to this design. 3. Actuators F3, F4, F5 and F6 are identical in appearance. 4. Loosening either the stem or bonnet connection will affect performance, may cause damage and will void the warranty. Refer to procedures in the IO&M instruction document. Contact the Warren Controls factory at (610) before attempting to reconfigure or reposition either the motor or linkage. Failure to do so will void the warranty 6 For additional applications, and/or products call: or visit: PS AMA F (a) 0411 ( )

7 Actuator Orientations Factory default and alternate actuator orientations are shown. If the alternate actuator orientation is required, select code A under special options in AmurAct order code. IMPORTANT SELECT THE CORRECT ACTUATOR ORIENTATION Each AmurAct actuator is precision factory calibrated on each valve prior to shipment. Field re-orientation of the actuator due to piping or other considerations can disturb the calibration and damage your AmurAct voiding the warranty. To prevent unneccessary field re-orientation be sure to select and order each AmurAct with the actuator in the correct orientation. DEFAULT ACTUATOR ORIENTATION ALTERNATE ACTUATOR ORIENTATION DEFAULT ACTUATOR ORIENTATION ALTERNATE ACTUATOR ORIENTATION

8 Dimensions & Weights LS LS LE 8 For additional applications, and/or products call: or visit: PS AMA F (a) 0411 ( )

9 Dimensions & Weights LS With Nema 4 Enclosure Dimension (IN) Type 50 Valve Size (IN) 1/2 3/ / / A 150FLG 7-1/4 7-1/4 7-1/4 8-3/ /8 11-3/4 13-7/8 17-3/ FLG 7-1/2 7-5/8 7-3/4 9-1/4 10-1/2 11-1/2 12-1/2 14-1/2 18-5/8 22 B 150FLG 6-1/2 6-1/2 6-1/2 6-1/ /4 11-1/4 13-7/8 15-7/ FLG 6-5/8 6-3/4 6-3/4 6-1/2 10-1/4 10-5/8 11-5/8 14-1/8 16-1/4 18 C Standard 5-1/2 5-1/2 5-1/2 6-1/8 8-1/8 8-7/8 9-5/8 10-3/8 13-7/8 15 Extension Bonnet CF CF CF CF CF CF 14-5/8 CF 17-5/8 C Weight (LB) Standard CF CF CF CF CF Extension Bonnet CF CF CF CF CF CF 215 CF 555 C 3-WAY Face to face dimensions conform to ANSI/ISA S75.03 CF = Consult factory N/A = Not Available Actual Shipping Weights May Vary Weight Motor lbs Dimensions F3 & F5 5 lbs 9.13 x 5.2 x 3.55 F4 & F6 8 lbs 9.13 x 5.2 x 3.55 Weight Linkage lbs Dimensions LS 11 lbs 9.5 x 9.5 x 3.25 LE 11.2 lbs x 9.5 x Emrick Blvd., Bethlehem, PA Tel: or Fax:

10 AmurAct Actuator LS Typical Construction 10 For additional applications, and/or products call: or visit: PS AMA F (a) 0411 ( )

11 LS Typical Construction AmurAct Actuator 2600 Emrick Blvd., Bethlehem, PA Tel: or Fax:

12 AmurAct Actuator LE Typical Construction 12 For additional applications, and/or products call: or visit: PS AMA F (a) 0411 ( )

13 LE Typical Construction AmurAct Actuator 2600 Emrick Blvd., Bethlehem, PA Tel: or Fax:

14 AmurAct Order Code SERIES: AMA A M A 5 0 L S Model VBA Series V A L V E B O D Y Valve Type Size Body Material End Connection Trim Style Trim Material Trim Cv Packing Type Bonnet Construction 1/2-1 1/ /2 inch 075 3/4 inch inch /4 inch /2 inch inch W WCB F CF8M F 150 lb. Flanged G 300 lb. Flanged L Linear S 316 SS F Full Port 1 1st Port Reduction 2 2nd Port Reduction 3 3rd Port Reduction Port reductions see page 3 T Teflon S 450 O F Tmax G 550 O F Tmax w. /Ext.Bonnet Temperature Limits Body Material End Connection Packing Type Bonnet Valve Type Code Code Code Construction Code T MAX T MIN 50 3-Way WCB W, CF8M F 150 lb F, 300 lb G Teflon T Standard S 450ºF 32ºF Mixing WCB W, CF8M F 150 lb F, 300 lb G Teflon T Extension Bonnet G 550ºF -20ºF NOTE: -20ºF T MIN temperature limit is for indoor applications with low humidity where ice will not form on the stem. 14 For additional applications, and/or products call: or visit: PS AMA F (a) 0411 ( )

15 L i n k a g e M o t o r E N C L O S U R E R a t i n g s p e c i a l LS Standard Linkage with orientation parallel to the pipe line LE Extended Temperature Linkage with orientation perpendicular to the pipeline and motor extended beyond linkage box. NOTE: LE linkage is required on valves with an extension bonnet. F3 120 in-lb Torque Motor with Enerdrive Fail Safe Back-Up 120VAC, 24VAC or 30Vdc Power Supply F4 F5 F6 240 in-lb Torque Motor with Enerdrive Fail Safe Back-Up 120VAC, 24VAC or 30Vdc Power Supply 120 in-lb Torque Motor with Enerdrive Fail Safe Back-Up 220VAC Power Supply 240 in-lb Torque Motor with Enerdrive Fail Safe Back-Up 220VAC Power Supply 00 No rating, somewhat splash resistant with proper fittings E2 NEMA 4X enclosure with heater and thermostat for use on 24 vac supply voltage only. (Check availability before ordering.) E3 NEMA 4X enclosure with heater and thermostat for use on 115 vac supply voltage only. (Check availability before ordering.) N4 Enclosure option for NEMA 4X. NOTE: Enclosure rating MUST match the operating voltage supplied to the motor. 0 No Special Options S Special Options verbally described on order, priced separately A Alternate actuator orientation IMPORTANT Size MOTOR TO USE TYPE 50 1/2 inch F3 or F5 YES F4 or F6 YES 3/4 inch YES YES 1 inch YES YES 1-1/2 inch YES YES 2 inch NO YES Notes: Please refer to page 5 for Shut-off P ratings. SELECT THE CORRECT ACTUATOR ORIENTATION Each AmurAct actuator is precision factory calibrated on each valve prior to shipment. Field re-orientation of the actuator due to piping or other considerations can disturb the calibration and damage your AmurAct voiding the warranty. To prevent unneccessary field re-orientation be sure to select and order each AmurAct with the actuator in the correct orientation Emrick Blvd., Bethlehem, PA Tel: or Fax:

16 PS AMA F (a) 0411 ( )