ADCATROL PNEUMATIC CONTROL VALVES PV16 ON-OFF (V16 globe valves series with linear actuators PA series)
|
|
- Arline Norton
- 5 years ago
- Views:
Transcription
1 TROL PNEUMTIC CONTROL VLVES PV16 ON-OFF (V16 globe valves series with linear actuators P series) DESCRIPTION The PV16G ON-Off valves are single seated, two-way body constructed with in-line straight connections. The P pneumatic actuator is rubber diaphragm and multi-springs. Its action can be D -direct action (air to close) or R-reverse action (air to open). Their wide application ranges allows to use this valve with the most common process fluids such as water, superheated water, steam, air, gas and other non corrosive fluids. MIN FETURES Single seated, two ways, direct or reverse action valve.valve top flange permanently attached to the body, removal is unnecessary for replacing the actuator. Soft sealing as standard. OPTIONS: USE: ir filter regulator Top-work manual handwheel Stainless steel construction. Saturated and superheated steam. Hot and superheated water. ir, gases and other noncorrosive fluids. VLVE BODY LIMITING CONDITIONS PV16G-OF Press. Temp. 16 bar -10 / 120ºC 15,5 bar 150ºC 14,7 bar 200ºC 13,9 bar 250ºC 12,8 bar 300ºC PV16I-OF Press. Temp. 16 bar -10 / 100ºC 14,5 bar 150ºC 13,4 bar 200ºC 12,7 bar 250ºC 11,8 bar 300ºC VILBLE MODELS: PV16G-OF - Nodular iron MX. IR SUPPLY PV16I-OF - Stainless steel PRESSURE: VLVE : DN15 to DN100 MBIENT TEMPERTURE: -20ºC...+70ºC CONNECTIONS: Flanged EN PN16 BONNET : From -5ºC to +220ºC (standard) Finned for temperature >220ºC CTUTORS: P-205; P-280; P-340; P-435 (from DN32 to DN100) STEM SELING: PTFE/GR V-Rings - up to 220ºC CTUTOR CONN: 1/4'' NPT-F (Standard bonnet) PLUG TYPES: On-Off (PT) PORT: Full port HOW TO SELECT: Never size the valve according to the pipe diameter in which it has to be fitted but according to the required actual flow of steam or water.refer to valve calculation data sheet or consult the factory. CE MRKING (PED - European Directive 97/23/EC) PN 16 Category DN15 to DN50 SEP - art. 3, paragraph3 DN65 to DN100 1 (CE Marked) VLSTEM IS PV16OF.70 E 10.06
2 DN DIMENSIONS - VLVE BODY (mm) B (mm) STD. C (mm) BONNET EXT (195) 265(295) (205) 270(300) (220) 300(330) *()Stainless steel version MTERILS POS. DESIGNTION MTERIL PV16G-OF MTERIL PV16I-OF 1 Valve Body GJS LT / CF8M / Bonnet CF8 / CF8 / ctuator (Steel) S235JRG2 / S235JRG2 / ctuator (St.steel) ISI 304 / ISI 304 / Diaphragm NBR 70 NBR 70 5 Yoke (Steel) C45E / C45E / Yoke (St.Steel) ISI 304 / ISI 304 / Valve seal PTFE/GR PTFE/GR 7 Standard packing PTFE/GR PTFE/GR Type DIMENSIONS - CTUTOR ø E (mm) D (mm) DN D/R WEIGHT Kgs P ,7 P ,8 P ,3 P ,5 FLOW RTE COEFFICIENTS DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 Kvs 3,8 5,1 9,4 15,4 22,2 40,1 63,4 89,7 136,7 Kvs in m3/h, see data sheet IS PV10.00 E ; For conversion Kvs = Cv(US) x 0,855 CTUTOR STROKE IN mm DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 Stroke VLSTEM IS PV16OF.70 E 10.06
3 MX. PERMISSIBLE PRESS.DROP IN bar - Normally closed valve (fluid to open) - CTUTOR (Pressure) MIN. IR PRESSURE DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 P-205 P-280 P-280B P-340 P-340B , ,5 4 5, , For valve sizes DN125 and above please consult. Special spring drops available on request. The pressure drop values must be used within the body rating limits CTUTOR MIN. IR (Pressure) PRESSURE DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 P-205 P-280B P-340B MX. PERMISSIBLE PRESS.DROP IN bar - Normally closed valve (fluid to close) - VLSTEM Important: not recommended for water and other liquids if fluid direction is over the plug (fluid to close). The pressure drop values are referred to closed valves CTUTOR MIN. IR (Pressure) PRESSURE DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 P-205 P-280 P-280B P-340B MX. PERMISSIBLE PRESS.DROP IN bar - Normally open valve (fluid to open) - Direct action actuator (air signal to close) , , For valve sizes DN125 and above please consult. The actuator pressure drops given with closed valve, are obtained with the following air pressures supply: ctuator signal 0,2 to 1 bar :air supply Special spring drops available on request. The pressure drop values must be used within the body rating limits. For electric actuator selection please consult catalogue IS EL E or our technical department. IS PV16OF.70 E 10.06
4 TROL PNEUMTIC CONTROL VLVES PPV25I ON-OFF (Complete stainless steel) (DN ½ 1 ) (V25I globe valves series with linear piston actuators PP series) DESCRIPTION The PPV25I on-off valves are single seated, two-way body constructed with in-line straight connections. The PPI pneumatic actuator is of the piston type. Their wide application ranges allows the use of this valve with the most common process fluids such as water, superheated water, steam, air, gas and other fluids. MIN FETURES Single seated, two ways, direct or reverse action valve. Soft sealing as standard. ctuator housing 360º rotation (clockwise). OPTIONS: ir filter regulator VLVE LIMITING Normally open and double effect CONDITIONS: Body design conditions: PN25 version. 25 bar at 10/50ºC Limit switch 21 bar at 200ºC Pilot solenoid valve 19,8 bar at 250ºC USE: Saturated and superheated steam. 18,5 bar at 300ºC Hot and superheated water. Min.working temperature: -10ºC ir, gases and other noncorrosive MX. IR SUPPLY fluids. PRESSURE: 8 bar VILBLE MBIENT MODELS: PPV25I - Stainless steel TEMPERTURE: -20ºC...+70ºC BONNET : From -5ºC to +220ºC (standard) VLVE : DN 1/2" to 1" STEM SELING: PTFE/GR V-Rings - up to 220ºC CONNECTIONS: Threaded ISO or NSI (Standard bonnet) CTUTORS: PPI-63 ( Stainless steel ) PLUG TYPES: On-Off (PT) CTUTOR CONN: G1/8" PORT: Full port as standard CONTROL SIGNL: 5-8 bar HOW TO SELECT: Never size the valve according to the pipe diameter in which it has to be fitted but according to the required actual flow of steam or water.refer to valve calculation data sheet or consult the factory. CE MRKING (PED - European Directive 97/23/EC) PN 25 Category DN 1/2" to 1" SEP - art. 3, paragraph3 VLSTEM IS PPV25I.50 E 01.09
5 MX. PERMISSIBLE PRESS.DROP IN bar - Normally closed valve (fluid to open) - CTUTOR DN 1/2" DN 3/4" DN 1" Kvs 5,2 Kvs 7,3 Kvs 11,7 PPI PPI Kvs in m3/h, see data sheet IS PV10.00 E ; For conversion Kvs = Cv(US) x 0,855 DIMENSIONS ( mm ) DN B C Ø D WEIGHT Kgs 1/2" , ,9 3/4" , ,9 1" , ,9 MTERILS POS. DESIGNTION MTERIL 1 Valve Body CF8M / Bonnet CF8M / ctuator Flange CF8 / ctuator Cover CF8 / Piston luminium 6 Indication Stem Plastic 7 Gland Nut ISI 316 / * Packing PTFE / GR 9 * Valve Plug / PTFE-GR * vailable spare parts VLSTEM IS PPV25I.50 E 01.09
6 ORDERING CODES PPV25I VLVE CODES Group Designation Pneumatic on-off valve Valve Model Two way straight design,stainless steel construction PPV.25I.X. PPV.25I Soft (PTFE/GR) PT Type Valve Plug 1 Pipe Connection Threaded BSP ISO 7/1 Rp Threaded NPT NSI B C Size DN 1/2" DN 3/4" DN 1" Fluid Direction Normally closed valve,fluid enter above the seat Normally closed valve,fluid enter below the seat ctuator Extras (3) B (1) E CTUTOR CODES ( pneumatic ) Group Designation Piston linear actuator ctuator Size Piston pneumatic actuator PPI 63 Piston pneumatic actuator PPI 90 PI. PI..63 To be introduced on ".X.", if supplied in combination with the valve. ctuator Type Direct action (air to close) Reverse action (air to open) ctuator Constrution Stainless steel.d.r (1)- Indicate actuator type. (2)- Omitted if the standard actuator is selected. (2) (3)- To be used only when a non-standard combination valve is supplied VLSTEM IS PPV25I.50 E 01.09
7 TROL PNEUMTIC CONTROL VLVES PPV16 ON-OFF (V16 globe valves series with linear piston actuators PPI series) DESCRIPTION The PPV16 on-off valves are single seated, two-way body constructed with in-line straight connections. The PPI pneumatic actuators are of the piston type. Their wide application ranges allows the use of this valve with the most common process fluids such as water, superheated water, steam, air, gas and other fluids. MIN FETURES Single seated, two ways, direct or reverse action valve. Soft sealing as standard. ctuator housing 360º rotation (clockwise). OPTIONS: USE: VILBLE MODELS: ir filter regulator Stainless steel construction. Normally open and double effect version. Limit switch Pilot solenoid valve Saturated and superheated steam. Hot and superheated water. ir, gases and other noncorrosive fluids. PPV16G - Nodular iron PPV16I - Stainless steel 12,8 bar 300ºC VLVE : DN15 to DN50 MX. IR SUPPLY CONNECTIONS: Flanged EN PN16 (PPV16G) PRESSURE: 8 bar Flanged EN PN16 (PPV16I) MBIENT CTUTORS: PPI-63, PPI-90 (Stainless steel) TEMPERTURE: -20ºC...+70ºC BONNET : From -5ºC to +220ºC (standard) CTUTOR CONN: G1/8" - G1/4" STEM SELING: PTFE/GR V-Rings - up to 220ºC (Standard bonnet) PLUG TYPES: On-Off (PT) PORT: Full port FLOW RTE COEFFICIENTS DN15 DN20 DN25 DN32 DN40 DN50 Kvs 5,2 7,3 11, VLVE BODY LIMITING CONDITIONS PPV16G Press. Temp. 16 bar -10 / 120ºC 15,5 bar 150ºC 14,7 bar 200ºC 13,9 bar 250ºC PPV16I Press. Temp. 16 bar -10 / 100ºC 14,5 bar 150ºC 13,4 bar 200ºC 12,7 bar 250ºC 11,8 bar 300ºC CE MRKING (PED - European Directive 97/23/EC) PN 16 Category DN15 to DN50 SEP - art. 3, paragraph3 VLSTEM IS PPV16.50 E 01.09
8 MX. PERMISSIBLE PRESS.DROP IN bar Normally closed valve (fluid to open) CT. Type IR PRESSURE DN15 DN20 DN25 DN32 DN40 DN50 PPI bar PPI bar Note: Waterhammer free design. MX. PERMISSIBLE PRESS.DROP IN bar Normally closed valve (fluid to close) CT. Type IR PRESSURE DN15 DN20 DN25 DN32 DN40 DN50 PPI bar PPI bar PPI bar PPI bar PPI bar PPI bar Note: not recommended when controlling liquids at high speed doing to waterhammer occurrence. DIMENSIONS (mm) C Ø D C Ø D DN B ctuator ctuator PPI-63 PPI-90 WHT. Kgs w/ppi63 WHT. Kgs w/ppi ,7 5, , , , ,7 11, ,7 13,2 MTERILS POS. DESIGNTION MTERIL PPV16G MTERIL PPV16I 1 Valve Body GJS LT / CF8M / Bonnet CF8 / CF8 / ctuator Flange CF8 / CF8 / ctuator Cover CF8 / CF8 / Piston luminium luminium 6 Indication Stem Plastic Plastic 7 Gland Nut ISI 316 / ISI 316 / * Packing PTFE / GR PTFE / GR 9 * Valve Plug / PTFE-GR / PTFE-GR * vailable spare parts VLSTEM IS PPV16.50 E 01.09
9 ORDERING CODES PPV16 VLVE CODES Group Designation Pneumatic on-off valve Valve Model Two way straight design,nodular iron construction Two way straight design,stainless steel construction Valve Plug Soft (PTFE/GR) PT Type PPV PPV.16G.16I 1.X. Flanged EN1092 PN16 Pipe Connection L Size DN 15 DN 20 Fluid Direction Normally closed valve,fluid enter above the seat Normally closed valve,fluid enter below the seat ctuator Extras (3) B (1) E CTUTOR CODES ( pneumatic ) Group Designation Piston linear actuator ctuator Size Piston pneumatic actuator PPI 63 Piston pneumatic actuator PPI 90 PI. PI To be introduced on ".X.", if supplied in combination with the valve. ctuator Type Direct action (air to close) Reverse action (air to open) ctuator Constrution Stainless steel.d.r (1)- Indicate actuator type. (2)- Omitted if the standard actuator is selected. (2) (3)- To be used only when a non-standard combination valve is supplied VLSTEM IS PPV16.50 E 01.09
ADCATROL INTERMITTENT BLOWDOWN VALVES VPA 26 (Fabricated steel)
TROL INTERMITTENT BLOWDOWN VLVES VP 26 (Fabricated steel) DESCRIPTION The VP26 blowdown valve was specially designed for application on steam boilers removing the concentrations of solids avoiding boiler
More informationPNEUMATIC CONTROL VALVES V403 DN65 DN100 (V403 globe valves series with linear actuators PA or EL series)
PNEUMATIC CONTROL VALVES V403 DN65 DN100 (V403 globe valves series with linear actuators PA or EL series) DESCRIPTION The PV403 control valves are three-way valves for mixing or diverting service. The
More informationADCATROL Pneumatic Control Valves PV25G (V25G globe valves series with linear actuators PA series)
ADCATROL Pneumatic Control Valves PV25G (V25G globe valves series with linear actuators PA series) DESCRIPTION The PV25G control valves are single seated, two-way body constructed with in-line straight
More informationPILOT OPERATED PRESSURE REDUCING VALVES PRV47 (Steel) PRV47I (St.Steel)
PILOT OPERATED PRESSURE REDUCING VALVES PRV47 (Steel) PRV47I (St.Steel) DESCRIPTION The PRV47 pilot operated pressure reducing valves are designed for use on steam, compressed air, nitrogen and other gases
More informationNON-RETURN VALVE RT25
NON-RETURN VALVE RT25 DESCRIPTION The RT25 all stainless steel disc check valve has a compact design and was specially designed for use with steam and hot condensate. Connections are female screwed MAIN
More informationPILOT OPERATED PRESSURE REDUCING VALVES PRV47/2 DN65 DN100
PILOT OPERATED PRESSURE REDUCING VALVES PRV47/2 DN65 DN100 DESCRIPTION The PRV47/2 pilot operated pressure reducing valves are designed for use on steam, compressed air, nitrogen and other gases compatible
More informationUNIWORLD series PNEUMATIC VALVES
UNIWORLD series PNEUMATIC VALVES 5100AD/E 07 2013 SINGLE SEAT TWO WAY ON-OFF VALVES PED 97/23/CE / ATEX 94/9/CE / MACHINERY DIRECTIVE 2006/42/CE TYPE 5100 AD Normally open air closes Face-to-face ASME
More informationSPIRA-TROL. DN15 to DN50. LE, LF and LL Two-port Control Valves
Page 1 of 10 Cert. No. LRQ 0963008 ISO 9001 SPIR-TROL DN15 to DN100 LE, LF and LL Two-port Control Valves TI-P303-11 CH Issue 2 Description SPIR-TROL is a range of two-port single seat globe valves with
More informationBCV Blowdown Control Valves DN15 to DN50 (½" to 2")
Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without
More informationGACHOT TYPE V16 BALL VALVES CARBON STEEL / FULL BORE / DN 8 TO DN 150
CRBON STEEL / FULL BORE / DN 8 TO DN 150 Carbon steel, forged body full bore ball valve designed to international and European standards FETURES PPLICTIONS Saturated steam. mmonia, natural gas, propane
More informationSpira-trol TM Two-port Control Valves EN Standard LE, LF and LL DN15 to DN100 and ASME Standard LEA, LFA and LLA ½" to 4"
Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without
More informationXV en /5 XV Knife gate valve DN
-80-800-en-04 1/5 The Stafsjö knife gate valve is a compact bi-directional valve with full bore. The valve is specially designed with regard to good flow characteristics and simple maintenance which makes
More informationGVI Series Industrial Globe Valves for Flow Control
Series Industrial Globe Valves for Flow Control 2-way Flow Control Globe Valves ssured utomations Series Industrial Globe Valves are contructed with rugged carbon steel or stainless steel bodies. They
More informationPF6 Stainless Steel Piston Actuated On/Off Valves
Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without
More informationPF6 Stainless Steel Piston Actuated On/ Off Valves
Page of TI-P7- CH Issue Cert. No. LRQ 9 ISO 9 PF Stainless Steel Piston Actuated On/ Off Valves Description A -port pneumatically actuated on / off stainless steel valve for use on steam, water, air, oil
More informationBALL VALVE SERIES Pneumatic actuator - Actreg
B C D E BALL VALVE - 516 SERIES Pneumatic actuator - Actreg FIGURE: AD: Pneumatic actuator, double acting AS: Pneumatic actuator, spring return G F A L DIMENSIONS: (mm) DN L A B AD AD C D E F Kg AS C D
More informationGATE VALVES ALV-1 FORGED STEEL NOMINAL PRESSURE NOMINAL SIZE MATERIALS CONNECTIONS. ANSI Class PN /4-2 DN 8-50.
FORGED STEEL GTE VLVES LV-1 NOMINL PRESSURE NSI Class 150-1500 PN 16-250 NOMINL 1/4-2 DN 8-50 MTERILS Carbon Steel Low lloy Steel Stainless Steel CONNECTIONS Socket Weld Butt Weld Threaded Flanged XELVLVES
More informationPRESSURE REDUCING VALVE DIRECT ACTING PRV 25/2 S Forged steel body. Saturated steam, compressed air and other gases compatible with the construction.
PRESSURE REDUCING VALVE DIRECT ACTING PRV / S Forged steel body DESCRIPTION The PRV/S series direct acting pressure reducing valves are designed for use on steam, compressed air and other gases. They are
More informationDIAPHRAGM SENSING PRESSURE REDUCING VALVE P 7 DN ¼ 3/8
DIPHRGM SNSING PRSSUR RDUING VLV P 7 DN ¼ /8 DSRIPTION The P7 series direct acting, spring-loaded diaphragm sensing, pressure reducing valves, are designed for use on steam and compressed air and other
More informationBALL VALVE WITH ADA PNEUMATIC ACTUATOR
702-703 BALL VALVE WITH ADA PNEUMATIC ACTUATOR DESCRIPTION The 702-703 ball valves are dedicated to the automatic shut off of industrial fluid s lines. It is a 3 pieces full valve with internal screws
More informationTwo port valves. pneumatically actuated
Two port valves pneumatically actuated One valve - The Spirax Sarco range of KE valves and PN5000 and PN6000 pneumatic actuators are designed to give a comprehensive selection of control valves for use
More informationWAYS BALL VALVES WITH ADA ACTUATOR
783-786 3-WAYS BALL VALVES WITH ADA ACTUATOR MAIN CHARACTERISTICS The three-ways flanged ball valve type 783-785 à brides is dedicated to the mixing or deviating functions in process of fluids. With full
More informationVALFONTA SELF-ACTING PRESSURE REDUCING VALVE M1
SELF-ACTING PRESSURE REDUCING VALVE M1 M1-15A-ENG PRESSURE REDUCING VALVE MODEL M1 VALFONTA MAIN CHARACTERISTICS The M1 model is self-operated bellows sealed pressure reducing valve. This series of regulators
More informationGachot Ball Valve Type V16 carbon steel / reduced bore / DN 8 to DN 200
carbon steel / reduced bore / DN 8 to DN 200 Three-piece ball valve featuring a unique design for easy and fast maintenance Features pplications Saturated steam. mmonia, natural gas, propane and utilities.
More informationVALFONTA USE, INSTALLATION AND MAINTENANCE MANUAL PNEUMATIC CONTROL VALVE MODEL C1
USE, INSTALLATION AND MAINTENANCE MANUAL PNEUMATIC CONTROL VALVE MODEL C1 CONTROL VALVE MODEL C1 - Operation and Installation - 1 - manual C1-13B-ENG.doc JANUARY 2014 INDEX PAGE 1 IDENTIFICATION PLATE
More informationSTAINLESS STEEL ARES PNEUMATIC ANGLE-SEAT VALVE
FEATURES The stainless steel ARES valve is intended for the automatic shut-off of networks of fluids. The full-bore, inclined-seat body and the excellent flow-rate coefficients allow for very low pressure
More informationButterfly valve with ADA pneumatic actuator
1133-1135 Butterfly valve with ADA pneumatic actuator MAIN CARACTERISTICS The 1133-1135 lug butterfly valves are dedicated to the automatic shut off of standard fluids lines. The construction includes
More informationSeries 240 Pneumatic On-off Valve Type 3351
Series 240 Pneumatic On-off Valve Type 3351 Application Control valve with a tight shutoff of liquids, gases and steam in accordance with DIN or ANSI standards Nominal sizes DN 15 to 100 NPS ½ to 4 Nominal
More information2/2-way Angle Seat Valve, manually operated, for media up to +180 C
2/2-way Angle Seat Valve, manually operated, for media up to +180 C Position indication Adjustable flow rates Stainless steel valve body Compact industrial design with long service life /2702 can be combined
More informationwith pneumatic actuator Pneumatic process valve, Y-pattern DN ARI-STEVI AS 350 Pneumatic actuator - with screwed sockets
with pneumatic actuator Pneumatic process valve, Y-pattern DN 15-50 ARI-STEVI AS 350 - with screwed sockets Piston actuator Required air supply pressure, max. 10 bar Operating pressure, max. 16 bar Page
More informationPROCESS & AUTOMATED VALVES
Process & utomated Valves HYDC s line of Process and utomated Valves complements our isolation valve knowhow and ability to supply high quality solutions to your valve requirements. 3-1 HV Series Inline
More informationBRONZE ZEUS PNEUMATIC ANGLE-SEAT VALVE
FEATURES The bronze ZEUS valve is intended for the automatic shutoff of networks of fluids. The full-bore inclined-seat body and the excellent flow-rate coefficients allow for very low pressure drops.
More information502 brass ball valve with ADA pneumatic actuator
502 brass ball valve with ADA pneumatic actuator MAIN CHARACTERISTICS The 502 valve is a brass ball valve dedicated to the automatic shut off of lines of standard fluids like water or air. With chromed
More informationPNEUMATIC VALVES HYGIENIC series
PNEUMATIC VALVES HYGIENIC series 1500AD/E 01 2004 THREE WAY DIVERTING CONTROL VALVES PED 97/23/CE Art.3 Section.3 Type 1500 AD TYPE 1500 AD Normally closed port C on air failure C = CLOSE A-B = OPEN DESCRIPTION
More informationBUTTERFLY VALVE WITH ADA PNEUMATIC ACTUATOR
1121-1125 BUTTERFLY VALVE WITH ADA PNEUMATIC ACTUATOR MAIN CARACTERISTICS The 1121 to 1125 wafer butterfly valves are dedicated to the automatic shut-off of medium pressure industrial fluids lines up to
More informationBUTTERFLY VALVE 1234P SERIES
FIGURE: AD: Pneumatic actuator, double acting AS: Pneumatic actuator, spring return ASRO: Pneumatic actuator, spring return, spring to open, air to close BUTTERFLY VALVE 1234P SERIES With pneumatic actuator
More informationControl Valves Series 2000 Heavy Duty valve 2 way
Series 2000 Heavy Duty valve 2 way Technical data Size (DN) DN 15 150 Pressure rating PN16, PN40 ANSI 300 Connections Flanges UNI/DIN PN16, PN40 Flanges ANSI 300 Type sealing Metallic (Class IV - V), soft
More informationELECTRIC ACTUATORS 400 N
ELECTRIC CTUTORS 400 N SE4 PPLICTION Electric actuator SE4 is suitable to drive valve body series in HVC systems. Two action types are available: - floating (3-point) - modulating Vdc and m. ctuator is
More informationBALL VALVE - 340BA SERIES Pneumatic actuator - El-O-Matic
C D E BALL VALVE - 30BA SERIES Pneumatic actuator - El-O-Matic FIGURE: PD: Pneumatic actuator, double acting PE: Pneumatic actuator, spring return G F DIMENSIONS: (mm) Ø DN C PD PE PD D E F Kg PE D E G
More information2/2-way Angle Seat Valve, manually operated, for media up to +180 C
2/2-way Angle Seat Valve, manually operated, for media up to +180 C Position indication Adjustable flow rates Stainless steel 316L valve body Compact industrial design with long service life /2702 can
More informationSPIRA-TROL. ½" to 4" ASME (ANSI) Two-port KEA, KFA and KLA Control Valves
Page 1 of 11 MNGMNT SYSTMS TI-P375-1 Issue 3 SPIR-TROL ISO 91 ½" to 4" SM (NSI) Two-port K, KF and KL ontrol Valves ert. No. LRQ 9638 Description SPIR-TROL is a range of two-port single seat globe valves
More informationBUTTERFLY VALVE - N1234 SERIES Pneumatic actuator - Actreg
B C D BUTTERFLY VALVE - N1234 SERIES Pneumatic actuator - Actreg FIGURE: AD: Pneumatic actuator, double acting AS: Pneumatic actuator, spring return G F L DIMENSIONS: (mm) DN L B AD AS AD C D F Kg AS C
More informationButterfly valve with ADA pneumatic actuator
A B Butterfly valve with ADA pneumatic actuator MAIN CARACTERISTICS The 1133-1135 lug butterfly valves are dedicated to the automatic shut off of standard fluids lines. The construction includes a long
More informationBOA-CVP H. Type Series Booklet
Control Valve BOA-CVP H PN 16/25 DN 20-150 Type Series Booklet Legal information/copyright Type Series Booklet BOA-CVP H KSB Aktiengesellschaft Pegnitz All rights reserved. Contents provided herein must
More informationSpecial Kv available. Classification according pressure equipment Directive, 2014/68/UE
SELF-OPERATED PRESSURE REGULATORS PRESSURE REDUCING VALVE MODEL PRV45 PRODUCT FEATURES Self-actuating pressure reducing valve balancing by diaphragm used to provide a constant downstream still there being
More informationBUTTERFLY VALVE - 18/28 SERIES Pneumatic actuator - El-O-Matic
B C D FIGURE: PD: Pneumatic actuator, double acting PE: Pneumatic actuator, spring return BUTTERFLY VALVE - 18/28 SERIES Pneumatic actuator - El-O-Matic G F L The pneumatic actuator is calculated for 6
More information2- and 3-port valves with flanged connections, PN 16
4 404 VXF43.. ACVATIX 2- and 3-port valves with flanged connections, PN 16 From the large-stroke valve line VXF43.. High-performance valves for medium temperatures from -20 220 C Valve body of nodular
More informationCE43 1" (DN25) to 4" (DN100) Carbon Steel Cage Design, Two Port Control Valves
Globe 13 CE43 1" (DN25) to 4" (DN) Carbon Steel Cage Design, Two Port Description The CE43 series is a range of carbon steel two port, cage trim, control valves conforming to ANSI B16.34, ASME VIII standards
More information2/2-way Globe Valve for media up to +180 C, DN
2/2-way Globe Valve for media up to +180 C, DN 10-100 Compact globe valve version Flange, threaded and welded ports as standard Stainless steel 316L valve body vailable with flow direction below and above
More informationFLANGED BALL VALVES ASME CLASS 150 & 300
FLNGED BLL VLVES SME CLSS 150 & REDUCED BORE: 1/2 (DN 15 500) SERIES 7000 The Jamesbury polymer-seated flanged ball valves provide industry leading performance and reliability. Offered in a wide variety
More information771 XS BALL VALVE WITH ADA PNEUMATIC ACTUATOR
771 XS BALL VALVE WITH ADA PNEUMATIC ACTUATOR MAIN CHARACTERISTIC The 771 XS wafer ball valve is dedicated to the automatic shut-off of low and medium pressure industrial fluids lines up to 16 bar. The
More informationBBV Automatic or Manually Actuated Boiler Blowdown Valves DN15 to DN65
Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development improvement of the product, we reserve the right to change the specification without
More informationARI-STEVI 450 / 451 (DN15-150) Control valve - 3-way-form (mixing/diverting valve) (optional with screwed seat ring)
With pneumatic and electric actuators Control valve - 3-way-form (mixing/diverting valve) (optional with screwed seat ring) ARI-STEVI 450 / 451 Pneumatic actuator ARI-DP 32-34T Reversible pneumatic actuator
More information736XS-746 XS VALVE WITH AP PNEUMATIC ACTUATOR
736XS-746 XS VALVE WITH AP PNEUMATIC ACTUATOR VALVE FEATURES The 736 XS-746 XS is a 3 pieces full bore ball valve for industrial fluids, especially made to be easily actuated and to offer a good and long
More informationSTERI-TROL Clean Service 'S' series Two-port and Three-port Control Valves - DN15 (½") to DN100 (4")
Page 1 of 17 Cert. No. LRQ 09608 ISO 9001 STERI-TROL Clean Service 'S' series Two-port and Three-port Control Valves - DN15 (½") to DN100 (4") TI-P183-02 CH Issue 3 Description STERI-TROL 'S' series are
More informationBALL VALVE SERIES Pneumatic actuator - Actreg
FIGURE: ADA: Pneumatic actuator, double acting ASR: Pneumatic actuator, spring return ASRO: Pneumatic actuator, spring return, spring to open, air to close BALL VALVE - 254 SERIES Pneumatic actuator -
More informationVALFONTA PRESSURE REGULATOR WITHOUT AUXILIARY ENERGY EXCESS PRESSURE VALVE (PRESSURE RELIEF VALVE) MODEL S1 MAIN CHARACTERISTICS
PRESSURE REGULATOR WITHOUT AUXILIARY ENERGY EXCESS PRESSURE VALVE (PRESSURE RELIEF VALVE) MODEL S1 MAIN CHARACTERISTICS The S1 model is self-operated bellows sealed pressure excess valve. This series of
More informationARI-STEVI 448 / 449 (DN15-100) Control valve in straightway form with screwed seat ring With pneumatic and electric actuators
ARI-STEVI 8 / 9 (DN5-00) Control valve in straightway form with screwed seat ring With pneumatic and electric actuators ARI-STEVI 8 / 9 Pneumatic actuator ARI-DP 30-3 Reversible pneumatic actuator Actuator
More informationVALVE FEATURES AVAILABLE MODELS LIMITS OF USE IP 67
VALVE FEATURES The resilient seat gate valve type is dedicated to the shut off of clear water and sewage water pipes. The motorization with the REGADA actuator allows the automation and the remote control
More informationValve Series V2001 Globe Valve Type 3321 with Pneumatic or Electric Actuator
Valve Series V2001 Globe Valve Type 3321 with Pneumatic or Electric Actuator Application Control valves designed for mechanical and plant engineering. Suitable for liquids, gases and steam Nominal size
More informationSoft sealing gate valves F4-F5 PN16. TYPE 02400/BV Soft sealing gate valve F4-F5 PN16
SLES SERVICE +8 (0)7 6 info@econosto.fi TYPE 000 DN0-0 TYPE 000 DN0-00 Soft sealing gate valves Nominal diameter options (DN) 0-00 Nominal pressure options (PN) 6 TYPE 000/BV-0-7 Soft sealing gate valve
More information2- and 3-port valves with flanged connections, PN 16
4 404 VVF43.. VVF43..K VXF43.. ACVATIX 2- and 3-port valves with flanged connections, PN 16 From the large-stroke valve line VVF43.. VXF43.. High-performance valves for medium temperatures from -20 220
More informationDiaphragm Valve, Metal
Diaphragm Valve, Metal Construction The GEMÜ pneumatically operated 2/2-way diaphragm valve has a low maintenance actuator. Normally Closed, Normally Open and Double Acting control functions are available.
More informationARI-STEVI BBD 415 (DN25-50) Straight through blow down valve
With pneumatic actuator ARI-STEVI BBD 415 (DN25-50) Straight through blow down valve ARI-STEVI BBD 415 Pneumatic actuator Required air supply pressure max. 6 bar Options: - Assembly of additional devices
More informationARI-STEVI 450 / 451 (DN15-150) Control valve - 3-way-form (mixing/diverting valve) (optional with screwed seat ring)
With pneumatic and electric actuators ARI-STEVI 450 / 451 (DN15-150) Control valve - 3-way-form (mixing/diverting valve) (optional with screwed seat ring) ARI-STEVI 450 / 451 Pneumatic actuator ARI-DP
More informationARI-STEVI 450 / 451 Pneumatic actuator ARI-DP 32-34T. Electric actuator ARI-PREMIO 2,2-25 kn ARI-PREMIO-Plus 2G 2,2-25 kn
ARI-STEVI 450 / 451 (DN15-150) Control valve - 3-way-form (mixing/diverting valve) (optional with screwed seat ring) With pneumatic and electric actuators ARI-STEVI 450 / 451 Pneumatic actuator ARI-DP
More informationSeries 240 Type 3351 Pneumatic On/off Valve
Series 240 Type 3351 Pneumatic On/off Valve Application Shut-off valve with tight shut-off for liquids, gases and vapors according to DIN or ANSI standards Valve size DN 15 to 100 NPS ½ to 4 Pressure rating
More informationSPIRA-TROL Two-port Control Valves ASME Standard KEA, KFA and KLA ½" to 8"
SPIRA-TROL Two-port Description SPIRA-TROL is a range of two-port single seat globe valves with cage retained seats conforming to ASME standard. These valves are available in three body materials in sizes
More informationControl Valve, Plastic/Metal
Control Valve, Plastic/Metal Construction The GEMÜ 2/2-way control valve has a stainless steel piston actuator. ll metallic actuator components are made of stainless steel. It is available with a normally
More informationPNEUMATIC VALVES HYGIENIC series
PNEUMATIC VALVES HYGIENIC series 1200AD/E 01 2004 SINGLE SEAT TWO WAYS PED 97/23/CE Art.3 Section 3 TYPE 1200 AD Normally open Air closes DESCRIPTION The 1200 HYGIENIC pneumatic control valves are with
More information715 XS BALL VALVE + ADA PNEUMATIC ACTUATOR
715 XS BALL VALVE + ADA PNEUMATIC ACTUATOR MAIN CHARACTERISTICS The 715 XS isolating valve is a two pieces ball valve for industrial applications with all compatible fluids. The body and the trim are full
More informationARI-STEVI ANSI (NPS 1/2" - 2") with electric and pneumatic actuators Control valve in straightway form
with electric and pneumatic actuators Control valve in straightway form ARI-STEVI 440 - ANSI Pneumatic actuator ARI-DP 32-33 Reversible pneumatic actuator Actuator with rolling diaphragm Air supply pressure
More informationBIDIRECTIONAL WAFER Knife Gate Valve
31/07/2014 BIDIRECTIONAL WAFER Knife Gate Valve - Bidirectional wafer-design knife gate valve. - One-piece cast body. - Provides high flow rates with low pressure drop. - Various seat and packing materials
More information516VX1VSSBIPD Pneumatic actuator - El-O-Matic
DN B 00 mm D E 56VXVSSBIPD Pneumatic actuator - El-O-Matic F E A L DIMENSIONS: (mm) DN L A B PD PE PD D E F Kg PE D E G Kg 5 5 53 6 25 266 286 59, 0 239 259 20 5,7 20 20 52 53 25 273 293 59, 65 258 278
More informationSTEVI 440 / 441. Straight through control valve DN
with electric and pneumatic actuators Straight through control valve DN 15-100 Electric actuator ARI-PREMIO Enclosure IP 65 2 torque switches 1 travel switch Handwheel Additional devices available, e.g.
More information600, 630. Diaphragm Valve, Plastic
Diaphragm Valve, Plastic Construction The /630 pneumatically operated 2/2-way valves have a low maintenance piston actuator which can be controlled by inert gaseous media. They have an integral optical
More informationBALL VALVE SERIES Pneumatic actuator - Actreg
B C D E BALL VALVE - 1515 SERIES Pneumatic actuator - Actreg FIGURE: AD: Pneumatic actuator, double acting AS: Pneumatic actuator, spring return G F A L DIMENSIONS: (mm) DN L A B AD AS AD C D E F Kg AS
More informationARI-STEVI 470 / 471 (DN15-150)
With pneumatic and electric actuators ARI-STEVI 470 / 47 (DN5-50) Control valve - straight through with screwed seat ring, shaftguided plug and blow-out protected stem ARI-STEVI 470 / 47 Pneumatic actuator
More informationSeries 2000 Top Guided Control Valve
Series 2000 Top Guided Control Valve Series 2000 Control Valve Series 2000 process Control Valves. Sturdy design with special service trims available for: Cavitation Control Noise Reduction Top entry construction
More informationPython Series Control Valves
Python - 1500 Series Control Valves Control valves are a key component in any pressure or temperature control application. With the increasing cost of fuel, delivering media in the most efficient way increases
More informationCONTROL EQUIPMENT STAZ-16, STBZ-16
CONTROL EQUIPMENT STZ-16, STZ-16 INSTLLTION & MINTENNCE 3-PORT SET VLVES VXF31 Used as a control valve for mixing and distribution of heating, ventilation and air conditioning systems. Only for closed
More informationData Sheet T EN
Data Sheet T 8015-1 EN Series 240 Types 3241 1 PSA, -7 PSA, -9 PSA Pneumatic Control Valves Type 3241 PSA Globe Valve Application Control valves for PSA plants (Pressure Swing Adsorption) Valve sizes DN
More informationBALL VALVE HIT SERIES Pneumatic actuator - El-O-Matic
B C D E BALL VALVE - 516 HIT SERIES Pneumatic actuator - El-O-Matic FIGURE: PD: Pneumatic actuator, double acting PE: Pneumatic actuator, spring return G F A L DIMENSIONS: (mm) DN L A B PD PD C D E F Kg
More informationSPIRA-TROL 1/2" to 4" ANSI Two-port KEA, KFA and KLA Control Valves
1/2" to 4" ANSI Two-port KEA, KFA and KLA Description SPIRA-TROL is a range of two-port single seat globe valves with cage retained seats conforming to ASME/ANSI standards. These valves are available in
More information3/2-Way Valve DN 15 up to DN 40
3/-Way Valve 78 DN up to DN Pneumatically operated 3/-way valve for the control of neutral and slightly aggressive media. (Stainless steel version, Data sheet Type 78) ompact design Unaffected by lightly
More informationT 8053 EN Type and Type Pneumatic Control Valves Type 3252 High-pressure Valve
T 8053 EN Type 3252-1 and Type 3252-7 Pneumatic Control Valves Type 3252 High-pressure Valve Application Control valve especially designed for controlling low flow rates in process engineering Valve sizes
More informationZEUS type BRONZE PNEUMATIC ACTUATED VALVE
CHARACTERISTICS The ZEUS bronze pneumatic actuated valve is dedicated to the automatic shut-off of fluid pipework. The full bore angle body and the great flow rates permit to have very limited pressure
More information2-Port Seat Valves with Flange, PN 25
4 7 2-Port Seat Valves with Flange, PN 25 VVF52... Nodular cast iron EN-GJS-400-8-LT valve body DN 5...40 k vs 0.6...25 m /h Can be equipped with SQX- electromotoric or SKD...- or SKB...- electrohydraulic
More informationSafety Relief Valves Commanche Techmatic Controls
Safety Relief Valves Commanche Techmatic Controls Product description Material Properties Connection W. Pres (Bar) W. Temp ( ) 1. Commanche-317 ISO 9001 (DN 12-50) SV-B27 Bronze Without lever Threaded
More informationSPIRA-TROL 1/2" to 4" ANSI Two-port LEA, LFA and LLA Control Valves
1/2" to 4" ANSI Two-port LEA, LFA and LLA Description SPIRA-TROL is a range of two-port single seat globe valves with cage retained seats conforming to ASME/ANSI standards. These valves are available in
More informationUniwat. Resilient Seated Gate Valves
Uniwat Resilient Seated Gate Valves www.comeval.es Resilent Seated Gate Valves - UNIWAT 504/507 Copyright COMEVAL VALVE SYSTEMS - Data subject to revision - Regularly updated data on www.comeval.es - DS01
More informationT EN Type 3347/3379 Pneumatic Control Valve Type 3347 Hygienic Angle Valve
T 8097-3 EN Type 3347/3379 Pneumatic Control Valve Type 3347 Hygienic Angle Valve Application Control valve for hygienic applications in the food and pharmaceutical industries Valve size DN 6 to NPS ¼
More informationFASANI PRESSURE SEAL CAST GLOBE VALVES - STYLE B Y AND T PATTERN
A wide range of globe valves specifically designed for high pressure and high temperature applications, where low pressure loss is required. FEATURES GENERAL APPLICATION Our pressure seal globe valves
More informationMaterials : Carbon steel or stainless steel
Size : Ends : Min Temperature : Max Temperature : DN 50 to 600 mm Between PN25 or PN16 flanges 29 C + 210 C Max Pressure : 25 Bars Specifications : Double eccentric Wafer type Fire safe according to ISO
More informationG4 Series. ...Extremely sensitive and accurate PILOT OPERATED PRESSURE REDUCING VALVES PRESSURE EQUIPMENT DIRECTIVE (PED) Adjusting Screw
G4 Series PILOT OPERATED PRESSURE REDUCING VALVES...Extremely sensitive and accurate The G4 pressure reducing valve is designed for use on steam, air and gases. It will maintain a constant outlet pressure
More informationMADE OF STAINLESS...
MADE OF STAINLESS... Size : Ends : Min Temperature : Max Temperature : DN 50 to 600 mm ( NPS 2" to 24" ) Between Class 150 (PN20) flanges 29 C + 210 C Max Pressure : 20 Bars Specifications : Double eccentric
More informationMaterials : Cast iron
Size : Ends : Min Temperature : Max Temperature : DN 15 to DN 200 Flanges ISO PN16-10 C + 300 C Max Pressure : 16 Bars Specifications : Rising rotating stem and handwhell Bolted bonnet and gland packing
More informationSeries 240 Pneumatic Control Valve Type and Type Globe Valve Type 3241
Series 240 Pneumatic Control Valve Type 3241-1 and Type 3241-7 Globe Valve Type 3241 Application Control valve for process engineering and industrial applications Nominal size DN 15 to 300 Nominal pressure
More informationwith electric and pneumatic actuators Control valve straight through with V-port plug DN ARI-STEVI 425 / 426
with electric and pneumatic actuators Control valve straight through with V-port plug DN 300-500 ARI-STEVI 425 / 426 Electric actuator AUMA SAR with LE Electric multiturn actuator capable of high closing
More informationARI-STEVI 440 / 441 DVGW type approval
ARI-STEVI 440 / 441 DVGW type approval Control valve in straightway form for combustible gases DIN-DVGW type approval DN 15-100 ARI-STEVI 440-G / 441-G for electric and pneumatic actuators DIN-DVGW type
More information