RPEK1-03/B. Functional Description HA /2011. RPEK1-03 Modular Valve Assembly. D n 03 p max 250 bar (3626 PSI) Q max 60 l/min (15.

Transcription

1 REK-03 Modular Valve ssembly REK-03/ /0 D n 03 p max 50 bar (366 SI) Q max 60 l/min (5.8 GM) Compact modular valve system assembly Easy to build complex circuits he possibility of subsequent rebuilding or extending the valve assembly High variability of functional options Functional Description Modular assembly blocks are designed for the control of one or more hydraulic circuits, used in open hydraulic circuits. he high variability of the modular set design allows its wide use in the construction of lifting and handling equipment, machine tools and also in the field of mobile technique. he base of the modular set is the body of the section distributor REK-03. he bodies are manufactured in more several variants, which enable horizontal and vertical assembly (see REK-03 directional valve data sheet H 407). Channels, run through all horizontal sections. Inlet flow is 60 L/min nominal, sectional flow is limited with performance of REK directional valve 0 L/min (5.8 GM) nominal. Channel,, which run through the upper surface of the distributor body are provided with threads G/4, or SE6-9/6-8 UNF, all measuring ports are G/4 or SE4-7/6-0 UNF Unthreaded outlets on the upper or side ground surface of the body are prepared for assembly. ressure and flow supply can be provided on the face side by a inlet, plate / block or in the centre of the assembled block using a central plate with radial ports of channels,. Furthermore, the block can be provided with a built-in pressure relief valve, which protects channel against overloading, and the solenoid controlled valve that allows channels - connection thus relieving the source of the pressure fluid to tank. he supply block with the proportional distributor is used for the flow regulation in the channel. Combination of 3 way pressure compensator and proportional valve allows to cave constant regulated flow independent of load. Vertical assembly allows installation of valves into channels,. In vertical stacking assembly is possible to mount throttle valves, or ilot operated check valves, and secundar pressure relief valves, Horizontal direction blocks, plates and bodies of distributors are connected into one unit using 3 screws / bolts and 4 bolts in the vertical direction. ll connected plates are sealed. wo fastening angles serve to mount the complete block to the base by screwing them to the face surfaces, or by using threads M6 at the bottom side of the plates and blocks. modular set allows horizontal assembly up to eight sections or up to sixteen sections when the centre plate is used for feeding and the blocks are grouped from both sides. It is possible to group up to four blocks vertically. In cases of more complicated block assemblies we recommend to first create a hydraulic circuit diagram.

2 d b c f f h e g.. M 5.. i Horizontal and Vertical ssembly llustrative Figure. REK.. Coils.. Electrical connector i) ressure plug G/4 (SE 6). Inlet, plates H03-REK-MZ a) SDE- b) SR- c) V-063 d) RM Sandwich plate H03-REK-M e) SO-Q3 4. Sandwich plate H03-REK-M g) S-3 h) Minimes 5. End plate H03-REK O check valve VJR Extension plate V-03-REK-0 8. Sandwich plate V03-REK-MC f) VSV 9. Cover plate V03-REK-0 0.Kit studs.kit... f e f f 0

3 CONEN. General description Directional Control Valve REK ilot Operated Check Valves for vertical assembly Connecting threads overview ssembly Guidelines Horizontal lates Overview of components for horizontal assembly Inlet, plates with valves Centre, plates Inlet, and End plates without valves Horizontal sandwich plates with valves ccesories ssembly Guidelines Vertical lates Overview of components for vertical assembly Extension plate ilot Operated Check Valve Vertical sandwich plate with valves Cover plate -, ports Measuring plate -, ports ccesories

4 Directional Control Valves Solenoid Operated REK-03 H 407 /0 Size 03 p max up to 50 bar (365 SI) Q max up to 0 L/min (5.8 GM) Replaces H 407 /007 4/3-, 4/ way directional control valves with solenoid control Solenoids can be turned around their axis to any position ush button manual override ossibility of vertical and horizontal assembly, see data sheet a a b b Functional Description Distributors of the REK-03 type are the basic elements for building blocks through horizontal and vertical assembly. his catalogue describes the preparation of the main unit, made up of two to eight distributors, by horizontal assembly. he distributors controlling the direction of the working fluid s flow to the individual appliances share common channels and. During the circuit design it is always necessary to check if the flow through the common channels covers the consumption of all appliances in all phases of the hydraulic equipment working cycle. Channels, outputs at the upper surface of the body are provided with threads G/4 (type G), or SE 9/6-8 (type S), or are prepared for vertical assembly (type O) i.e. brought out onto a ground surface. Channels,,, outlets on the side surfaces of the body are prepared for horizontal assembly i.e. brought out onto a ground surfaces or provided with he standard design of the emergency control may be additionally fitted with a pushbutton with a rubber cover. a sealing ring recess. he individual distributor bodies are connected into a compact block using three bolts. Fastening angles serve to mount the block to the base with four screws. n assembled block feed is provided by a plate with connecting threads G3/8 in channels,. It is also possible to use plate with a built-in pressure relief valve to regulate the maximum pressure in the circuit. Use data sheet No. H 507 to create more complex assemblies with the use of the horizontal and vertical assembly, while also using additional building elements. he REK-03 directional control valves consist of cast iron housing (), control spool (5) with two centering springs (4) and operating solenoids (, 3). he three-position directional valves are fitted with two solenoids, two-position directional valves have either one solenoid. *he operating solenoids are DC solenoids supplied through connectors, (6, 7). For C supply the solenoids are provided with rectifiers, which are integrated directly into the connectors, (6, 7). the connectors can be turned by 90 around. y loosening the nut (8), the solenoid can be turned around its axis up to 360. In the case of solenoid malfunction or power failure, the spool of the valve can be repositioned by manual override (9), provided the pressure in the -port does not exceed 5 bar.he standard design of the emergency control may be additionally fitted with a pushbutton with a rubber cover. he basic surface treatment of the valve housing () is phosphate coated and the solenoids (, 3) are zinc coated. *Magnet coils are not included in the valve supply. he coil types selected by the customer must be ordered separately. ype of connection "O" ype of connection "G", "S" a b 4

5 Ordering Code REK-03 / Solenoid Operated Directional Control Valve Nominal size no designation V Seals NR FM (Viton) ype of connection G/4 G SE 9/6-8 S without thread O Design form no designation standard through channels, ; inlets, with sealing rings Z one side inlets of channels, with sealing rings Z3 one side inlets of channels,,, with sealing rings Number of valve positions two positions three positions 3 no designation Manual override * standard Functional symbols see the table functional symbols *he standard design of the manual override may be additionally fitted with a pushbutton with a rubber cover (N). Note: solenoid coil, electrical connector and manual override (N) is not supplied as mounted on, must be ordered separately (see ordering number on page 0, ) echnical Data Nominal size 03 Maximum flow l/min (GM) see p-q characteristics Maximum operating pressure at ports,, bar (SI) 50 (365) Maximum operating pressure at port bar (SI) 0 (3045) ressure drop bar (SI) see p-q characteristics Hydraulic fluid Hydraulic oils of power classes (HL, HL) to DIN 5 54 Fluid temperature range NR C ( F) ( ) Fluid temperature range FM (Viton) C ( F) ( ) mbient temperature, max. C ( F) up to +50 (+) Viscosity range mm /s (SUS) ( ) Maximum degree of fluid contamination Class /8/5 to ISO 4406 (006) Maximum allowable voltage variation % C: 0 DC: 0 Maximum switching frequency /h Switching time, ON; at = 3 mm /s ms Switching time, OFF; at = 3 mm /s ms C: DC: Duty cycle % 00 Service life cycles 0 7 Enclosure type to EN see page 0 Weight - valve with solenoid - valve with solenoid Mounting position kg (Ib) 0.90 (.98),05 (.3) optional 5

6 Functional Symbols Designation Symbol Interposition Designation Symbol Interposition p-q Characteristic Measured at = 3 mm /s (56 SUS) Operating limits for maximum hydraulic power transferred by the directional valve. Operating pressure p in bar [SI] (366) (90) (76) (450) (75) 50,, 3, 4, ,, 3, 4, (.3) (.64) (3.96) (5.8) Flow Q in l/min [GM] Z Z5 R R C C5 H Y Y p-q Characteristic ressure drop p ralated to flow rate. Measured at = 3 mm /s (56 SUS) ressure drop p inbar[si] (76) (450) (75) (.3) (.64) (3.96) (5.8) Flow Q in l/min [GM] 6 Z C H Y R R Y5 C5 Z

7 Valve Dimensions Standard body version "G", "S" G S HRED G/4 SE6-9/6-8UNF D [mm] 0,9H3 5 +0,5 D [in] [mm (in)] (0.039) 0,5 (0.00) 56(.05) 33(.99) 3(0.5) 0(0.394) a () D HRED (5) (5) ((0.59)) ((0.59)) 8 3x 6,4(0.5) 9 x 8 (0.35) () Valve with two solenoids b, (0.480) 4(0.945) 4(0.945) 30,5(.0) 6(.40) 5,5(.8) 3(.0) (3,) ((0.50)) 4,(.6) 44,4(.748) 6(0.473) (0.47) 79(7.047) 59(.33) ( 0,8(0.45)) ( 5,3(0.09)),4(0.488) 8(0.35),4(0.055) 30(.8) Valve with one solenoid "a" Functional symbols R, R, Y5, C5, Z5 a 30(.8) 5,5(.8) Solenoid a * Solenoid b * 3 Manual override 4 Name plate 5 Square ring 9,5 x,68 ( ks.) supplied with valve 6 3 mounting holes 7 Retaining nut of the solenoid 8 Electrical connector, EN Space required to remove connector 0 Outlets / are only at the versions, Z; Z3, Seal 7,65x,68 * must be purchased separately (see page 7) 3,5(4.86) 7(0.75) Valve with one solenoid "b" Functional symbols H Required surface finish of interface b * must be purchased separately (see page 7) 7

8 Valve Dimensions Standard body version "O" Valve with two solenoids 8,5(0.335) 3x 6,4(0.5) 4xM (0.473) (0.47) 56(.05) 33(.99) 8(0.34) a () () (5) (5) (0.59) (0.59) x 8 (0.35) x45 (0.47) 5(0.59) b, (0.480) (3,) ((0.50)) 4,(.6) 44,4(.748) 5,8 (0.8) 4(0.945) 4(0.945) 30,5(.0) 6(.40) 59(.33) 79(7.047) ( 0,8(0.45)) ( 5,3 (0.09)),4(0.488) 8(0.35),4(0.055) 30(.8) 5,5(0.60) 3(.0) 4,6(0.8) 6,4(.039) ,(.64) Valve with one solenoid "a" Functional symbols R, R, Y5, C5, Z5 a 30(.8) 56,9(.40) 7(0.75) 5,5(0.60) Solenoid a * Solenoid b * 3 Manual override 4 Name plate 5 Square ring 9,5 x,68 ( ks.) supplied with valve 6 3 mounting holes 7 Retaining nut of the solenoid 8 Electrical connector, EN Space required to remove connector 0 Outlets / are only at the versions, Z3, Seal 7,65x,68 * must be purchased separately (see page 7) 3,5(4.86) Valve with one solenoid "b" Functional symbols H Required surface finish of interface b 8

9 Design form "G" ( "S"), "O" - "G"( "S") hrough channels, ; outlets, with sealing rings, - "O", 4xM5 for vertical assembly,, Z - "G"( "S") Z - "O" one side inlets of channels, with sealing rings (outlets, only on the upper surface),, Z3 - "G"( "S") combination of options Z a one side inlets of channels,,, with sealing rings Z3 - "O",, Spare Seal kit Dimensions, number Ordering nr. ype Sealing - ring O-ring Z Standard 9,5 x,68 NR 70 ( ks.) 6 x NR 90 (ks.) ype Dimensions, number Ordering nr. Sealing - ring O-ring Sealing - ring, Z3 Standard 9,5 x,68 NR 70 ( ks.) 6 x NR 90 ( ks.) 7,65 x,68 ( pcs.) Viton 9,5 x,78 ( pcs.) 6 x ( pcs.) 7,65 x,78 ( pcs.)

10 Manual Override SNDRD RUER OO NO DESIGNION N Ordering number / Kit KI N 8(0.709) 9,5(.6) Standard model of the manual override. Standard retaining nut of the solenoid. Dimensions of Coils C4 Manual override protected by rubber boot. Kit must be purchased separately. Connector design E, E EN E3, E4 M Junior imer E, E3 Deutsch D04- rotection degree I65 rotection degree I65 rotection degree I67, I69 0(0.79) 3,4(0.53) 30(.8) 34,(.34) 3,4(0.53) 30(.8) 39,3(.55) 3,4(0.53) 30(.8) 4(.6) 4(.6) 4(.6) 0 Coils C4 Nominal voltage Nominal current Connector ype code Note: * Coil version 05 are suitable for the rectified voltage of 30V /50Hz, Rectifier in coil included Other designs available at request. Ordering number VDC,83 E - EN C4-000E-6,55N VDC 0,9 E - EN C4-0400E-6,N V DC* 0,08 E - EN C4-0500E-476N VDC,83 E - E with quenching diode C4-000E-6,55N VDC 0,9 E - E with quenching diode C4-0400E-6,N VDC,83 E3 - M Junior imer ( pins; male) C4-000E3-6,55N VDC 0,9 E3 - M Junior imer ( pins; male) C4-0400E3-6,N VDC,83 E4 - E3 se zhášecí diodou C4-000E4-6,55N VDC 0,9 E4 - E3 se zhášecí diodou C4-0400E4-6,N VDC,83 E - Deutsch D04- C4-000E-6,55N VDC 0,9 E - Deutsch D04- C4-0400E-6,N VDC,83 E3 - E se zhášecí diodou C4-000E3-6,55N VDC 0,9 E3 - E se zhášecí diodou C4-0400E3-6,N

11 Spare arts Electrical connector Solenoid coil - see coils table 3 Nut with seal 4 Seal kit 3 b a 4 Solenoid retaining nut with seal ype of the nut - Mu 3 Nm(.lbs-ft) Seal ring Ordering number Standard nut 3 x Manual Override N Electrical connector, EN ype designation K K K3 K4 K5 Model without rectifier - M6x,5 bushing bore 6-8 mm ( in) without rectifier with LED and quenching diode M6x,5 bushing bore 6-8 mm ( in) with rectifier - M6x,5 bushing bore 6-8 mm ( in) with rectifier with LED and quenching diode - M6x,5 bushing bore 6-8 mm ( in) without rectifier - M6x,5 bushing bore 4-6 mm ( in) Max. input voltage Connector grey Ordering number Connector black 30 V C/DC V DC V C V C V C/DC Caution When the distributor contains two electromagnets any of the two electromagnets can be switched on only after the other one switches off. Distributors with other interconnections than those shown in the catalogue can be supplied on request. he packaging foil can be recycled he transport base plate can be returned to the manufacturer. he mentioned data only serve to describe the product and in no case are to be understood in terms of law as guaranteed characteristics.

12 ilot Operated Check Valves Sandwich lates VJR5-03/M H 507 /0 Size 03 p max up to 50 bar (365 SI) Q max up to 0 l/min (5.8 GM) Sandwich plate design for use in vertical stacking assemblies 3 models: leakfree closure of both sides with check valves in lines and leakfree closure with check valve in line leakfree closure in line Functional Description hydraulic lock serves to close tightly a hydraulic circuit under pressure. It provides a load against a pressure drop and secures a stable position of piston of the cylinder under pressure also for a longer period. he valve consist of an aluminium body (), one or two check valves (), (3) and a control piston (4). If a fluid is flowing in the direction from () into (), a ball lifts ()or (3), and the control piston (4) shifts at the same time to the right (left) and pushes out the ball (3) or () from the seat. his releases the connection ( ). If the pressure drops in channels and (e.g. when the distributor shifts to the centre position), the spring presses the ball springs () and (3) into the seats and the cylinder circuit is closed under pressure. o ensure a tight seal of the spaces and, the distributor with Y interconnection must be used, which, when in the centre position, connects both sides of the control piston (4) with the tank. Without surface finish.

13 Ordering Code VJR5-03/M ilot Operated Check Valve Sandwich late no designation V Seals NR FM (Viton) Nominal size Modular design C Functional Symbols check valve in line * check valve in line * check valves in lines and * * see the table Functional symbols Functional Symbols rrangement of the check valves in the valve body VJR5-03/M VJR5-03/M VJR5-03/MC echnical Data Nominal size 03 Maximum flow L/min (GM) 0 (5.8) Maximum operating pressure bar (SI) 50 (365) Cracking pressure bar (SI) 0,5 (3.65) Hydraulic fluid Hydraulic oils of power classes (HL, HL) to DIN 554 Fluid temperature range (NR) C ( F) ( ) Fluid temperature range (Viton) C ( F) ( ) Viscosity range mm /s ( ) Maximum degree of fluid contamination Class /8/5 to ISO 4406 (006) rea ratio (pilot piston / poppet) 3 : Mounting position optional Weight kg (lb) 0, (0.44) 3

14 p-q Characteristics Measured at = 3 mm /s (56 SUS) ressure drop p related to flow rate. ressure loss with distributor REK-033/Y ressure drop p [bar (SI)] Flow in direction ( ) ( ) Flow Q [L/min (GM)] Valve Dimensions 6 (.40) 5.8 (.079) 4. (.68) 4. (0.6).4 (0.449).8 (0.858) 30 (.8) 40 (.575) 4x 5.3 (0.09) 0 (0.787) Required surface finish of interface 0.9 (0.49) 4. (0.6) 5 (0.59) 4 mounting holes Square ring 9.5 x.68 ( pcs.) supplied with valve 4 Spare arts Seal kit ype Dimensions, quantity Square ring O-ring Ordering number Standard NR70 9,5 x,68 ( pcs.) 4,47 x,78 ( pcs.) Viton - 9,5 x,78 ( pcs.) 4,47 x,78 ( pcs.)

15 ( hreaded Chambers for the REK Kit Connecting INLE/OULE ORS FOR HORIZONL ND VERICL SSEMLY G3/8..., G/4... M,, 0,(0.004) 0,( ) +0,5 3 ( ) G3/8 + ( , C ) 0,0) ,( 0,(0.004) 0,( ) 0 +0, (0.79 ) G/4 + ( , C 0,0) ,( SE8-3/4-6 UNF..., SE6-9/6-8 UNF..., , (.8 ) 0,65+0,05 ( ) 30 0,(0.008) 3, +0, ( ,7 0,05 ( ) 3. C 0,(0.004) 4,3 (0.56 ) ,5 (0.69 ) +0, ,( ) +0, ,5 ( /6-8 UNF )),7 (0.5 5,5 0, (0.6 ) G/..., SE4-7/6-0 UNF... M 0. 0,( ) +0, (.0 ) G/ ) + ( , C 7 0,( ,0) 5

16 HORIZONL SSEMLY LES - 8 sections (up to 6 sections when using centre feeding plate with bolt threads from both sides) Complete valves in modular configuration REK-03 Dn03 Data sheet H L=3 mm (. in) ype Cavity Connecting threads Inlet, lates with Valves Ordering number age Description (to select the studs) H03-REK-M / - 7/8-4UNF G 3/8 -,, G /4 - M H03-REK-M-S / - 7/8-4UNF SE 8 -,, SE 4 - M H03-REK-M / - 7/8-4UNF G 3/8 -,, G /4 - M H03-REK-M-S / - 7/8-4UNF SE 8 -,, SE 4 - M H03-REK-M / - 7/8-4UNF G / -,, G /4 - M H03-REK-MZ / - 7/8-4UNF G 3/8 -, H03-REK-MZ-S / - 7/8-4UNF SE 8 -, Centre, lates olt threads from both sides H03-REK-0 G 3/8 -,, H03-REK-0-S SE 8 -, H03-REK-0 G 3/8 -,, G /4 - M H03-REK-0-S SE 8 -,, SE 4 - M Straight-through holes for bolts H03-REK-03 G 3/8 -, L=3 mm (. in) H03-REK-03-S SE 8 -, L=3 mm (. in) H03-REK-04 G 3/8 -,, G /4 - M L=3 mm (. in) H03-REK-04-S SE 8 -,, SE 4 - M L=3 mm (. in) Inlet, and End lates without Valves Without recess for sealing rings H03-REK L3=4 mm (0.55 in) H03-REK-06 G 3/8 -,, G /4 - M L=3 mm (. in) H03-REK-06-S SE 8 -,, SE 4 - M L=3 mm (. in) With sealing rings recess H03-REK-07 G 3/8 -,, G /4 - M L=3 mm (. in) H03-REK-07-S SE 8 -,, SE 4 - M L=3 mm (. in) H03-REK L3=4 mm (0.55 in) Horizontal Sandwich lates with Valves H03-REK-M 3/ - 3/4-6UNF G /4 - M L=40 mm (.57 in) H03-REK-M-S 3/ - 3/4-6UNF SE 4 - M L=40 mm (.57 in) H03-REK-M 3/ - 3/4-6UNF G /4 - M L=40 mm (.57 in) H03-REK-M-S 3/ - 3/4-6UNF SE 4 - M L=40 mm (.57 in) H03-REK-MC / - 3/4-6UNF L=40 mm (.57 in) H03-REK-MD / - 3/4-6UNF L=40 mm (.57 in) H03-REK-M / - 3/4-6UNF G /4 -, L=40 mm (.57 in) H03-REK-M-S / - 3/4-6UNF SE 6 -, L=40 mm (.57 in) H03-REK-M M0x,5 G /4 -, L=40 mm (.57 in) H03-REK-M-S M0x,5 SE 6 -, L=40 mm (.57 in) H03-REK-M / - 3/4-6UNF L=40 mm (.57 in) Other possible assembly parts - for connecting material see pages 3, pressure plug can be ordered measuring outlet and off the, - G/4 valve outlet. - pressure plug can be ordered measuring outlet and off the, - SE 6 valve outlet. - pressure plug can be ordered to blank off the M - SE 4. 6

17 Inlet alate H03-REK-M/-(S) /(93400) Z Z Z Z Z3 Z3 L Z4 Z4 Z4 M Z3 REK-03 Z X Y X = Z, Z3, Z4, Z5 Y = Z, Z, Z3, Z5 os. Name ype Max. L [mm (in)] Weight [kg (Ib)] Data sheet Ordering nummer Inlet alate H03-REK-M ,83(.79) H03-REK-M-S Z Directional valve SDE- 8 (3.3) H 4060 Z ressure valve SR- 65 (.56) H 5064 Z3 Directional valve SD3E- 8 (3.3) H 4063 Z4 Check valve SCF- 8 (.0) H 507 Z5 lug /-7/8-4UNF 0 (0.39) Valve Dimensions - M/-(S) xm6/(0.47) 3,5(.8) YE G 9,5 (.6) 56 (.0) SE 3(.) 54 (.3) 37(.45) 4,5(0.57) 50(.97) 48(.90) xm6/(0.47) 5,5(0.6) 35(.38) 3xM6/4(0.55) 5,6 (0.) 68(.68) 5,5() 4,5(0.57) 4(0.94) 4(0.94) 38,5(.5) 43,5(.7) 65(.56) 4(0.94) 4(0.94) 38,5(.5) 4,5(0.57) 77(3.03) 5,5(),(0.48) 4,(.6) 44,4(.74) Cavity: / way 7/8-4 UNF Connecting threads:,... G3/8, (SE 8) Measuring output: M... G/4, (SE 4) 7

18 Inlet alate H03-REK-M/-(S) /(934300) M REK-03 Z L Z Z os. Name ype Max. L [mm (in)] Weight [kg (Ib)] Data sheet Ordering nummer H03-REK-M Inlet alate 0,407(0.897) H03-REK-M-S Z ressure valve SR- 65 (.56) H 5064 Valve Dimensions - M/-(S) xm6/(0.47) (0.83) 4,5(0.57) 48(.90) 77(3.03) 50(.97) xm6/(0.47) 5,5(0.6) 35(.38) 3,5(.4) 3xM6/4(0.55) 5,6 (0.),(0.48) 4,(.6) 44,4(.74) 68(.68) 4,5(0.57) 4(0.94) 4(0.94) 9(0.75) 4(0.94) 4(0.94) 4,5(0.57) 38,5(.5) 57(.4) (0.83) 4(.65) Cavity: / way 7/8-4 UNF Connecting threads:,... G3/8, (SE 8) Measuring output: M... G/4, (SE 4) 8

19 Inlet alate H03-REK-M Z Z L Z4 Z3 Z4 Z Z3 X M Y REK-03 Z X = Z, Z3, Z4, Y = Z os. Name ype Max. L [mm (in)] Weight [kg (Ib)] Data sheet Ordering nummer Inlet alate H03-REK-M (.059) Z Directional valve SDE- 8 (3.3) H 4060 Z ressure valve SR- 65 (.56) H 5064 Z3 Directional valve SD3E- 8 (3.3) H 4063 Z4 lug /-7/8-4UNF 0 (0.39) Valve Dimensions - M xm6-6h/(0.47) 58(.8) 35(.38) 86(3.39) xm6-6h/(0.47) 8(0.7) 8,5.) 7(.8) 86(3.4) 50(.97) 3xM6-6H/4(0.55) 8 44,4(.75 ) 4,5(0.57) 48(.89) 77(3.03) 7,5(0.67) 48(.89) 4,5(0.57) 3(.6) 3,5(.8) 4,5(0.57) 48(.89) (0.7) 34(.34) 38,5(.5) Cavity: / way 7/8-4 UNF Connecting threads:,... G / Measuring output: M... G/4 9

20 RGO-HYOS HD 4057 Inlet alate H03-REK-MZ/-(S) /(934400) xm6/(0.47) 3,5(.4) 34,5(.34) 7(0.67) 3(.) 3,5(.8) 70(.76) 35(.38) V Z4 Z L REK-03 Z3 Z4 Z Z Z Z3 os. Name ype Max. L [mm (in)] Max. V [mm (in)] Weight [kg (Ib)] Data sheet Ordering nummer Inlet alate H03-REK-MZ H03-REK-MZ-S Z Directional valve SDE- 8 (3.3) H 4060 (.865) Z ressure valve SR- 65 (.56) H ,846 Z3 3 way ressure compensator V (.65) H 568 Z4 roportional valve RM (5.5) (4.76) H 505 Z3 lug /-7/8-4UNF 0 (0.39) Valve Dimensions - MZ/-(S) 4,5(0.57) 50(.97) xm6/(0.47) 48(.90) 5,5(0.6) 35(.38) 3,5(.4) 3xM6/4(0.55) 5,6 (0.),(0.48) 0,75(0.03) 5,(0.) 5,5(0.6) 4,(.6) 44,4(.74) 68(.68) 34(.34) 4,5(0.57) 4(0.94) 4(0.94) 5() 4(0.94) 4(0.94) 4,5(0.57) 9(0.75) 38,5(.5) 38,5(.5) 77(3.03) 3(0.5),5(0.85),7(0.50) 4xM5/3(0.5) 30,(.9) 40,5(.59) Cavity: / way 7/8-4 UNF Connecting threads:,... G 3/8/ (SE 8) 0

21 C Centre, late H03-REK-0/-(S) /( ) - olt threads from both sides xm6/(0.47) 48(.89) 5,5(0.6) 4,5(.) 5,6 (0.) 8,5(0.73) x,4(0.49) 3xM6/4(0.55) x 8(0.3),(0.48) 4,(.6) 44,4(.74) 34(.34) 68(.68) 3xM6/4(0.55) x 8(0.3) 5,6 (0.) 44,4(.74) 5,5(0.6) 4(0.94) 4(0.94) 4,5(.) 5,5(0.6) 4(0.94) 4(0.94) 4,5(.) 38,5(.5) 3(.) 77(3.03) Centre, late H03-REK-0/-(S) /( ) - olt threads from both sides xm6/(0.47) 48(.89) 5,5(0.6) 4,5(.) 5,6 (0.) M x,4(0.49) x 8(0.3),(0.48) 4,(.6) 44,4(.74) 68(.68) 3xM6/4(0.55) x 8(0.3) 5,6 (0.) 44,4(.74) 3xM6/4(0.55) 5,5(0.6) 4(0.94) 4(0.94) 4,5(.) 3(.) 4(0.94) 4(0.94) 4,5(.) 38,5(.5) 77(3.03) 5,5(0.6) YE C,5 3 0 G (0.89) (.60) (0.79) SE 0, (0.8) (.4) (0.94) Name ype ort size Ordering number Weight [kg (Ib)] M late+seals H03-REK-0 G3/8 G3/ ,38 late+seals H03-REK-0-S SE 8 SE (0.70) late+seals H03-REK-0 G3/8 G3/8 G/ ,38 late+seals H03-REK-0-S SE 8 SE 8 SE (0.70)

22 Centre, late H03-REK-03/-(S) /( ) - through holes for bolts - straight xm6/(0.47) 48(.89) 5,5(0.6) 4,5(.) 5,6 (0.) 8,5(0.73) x,4(0.49) 3x 6,4(0.5),(0.48) 4,(.6) 44,4(.74) 34(.34) 68(.68) x 8(0.3) HRU 5,5(0.6) 4(0.94) 4(0.94) 4,5(.) 77(3.03) 38,5(.5) 5,5(0.6) 3(.) Centre, late H03-REK-04/-(S) /( ) - through holes for bolts - straight xm6/(0.47) 48(.89) 5,5(0.6) 4,5(.) 5,6 (0.) M C x,4(0.49) 3x 6,4(0.5) HRU,(0.48) 4,(.6) 44,4(.74) 68(.68) x 8(0.3) HRU 5,5(0.6) 4(0.94) 4(0.94) 4,5(.) 3(.) 77(3.03) 30,5 5,5(0.6) YE C G,5 3 0 (0.89) (.60) (0.79) SE 0, (0.8) (.4) (0.94) Name ype ort size Ordering number Weight [kg (Ib)] M late+seals H03-REK-03 G3/8 G3/ ,35 late+seals H03-REK-03-S SE 8 SE (0.694) late+seals H03-REK-04 G3/8 G3/8 G/ ,305 late+seals H03-REK-04-S SE 8 SE 8 SE (0.67)

23 End late H03-REK without sealing rings 5,8 (0.3) 3x 6,4 HRU (0.5 HRU) 44,4(.74) 56(.30) 4(0.94) 4(0.94) 6,5(0.5) 4(0.55) 6(.40) Inlet, late H03-REK-06/-(S) /( ) - without recess for sealing M YE G 3 (0.9) 3 (0.9) SE 8 (0.7) (0.83) xm6/(0.47) 5,5(0.6) 48(.89) 4,5(.),5(0.49) 5,6 (0.) 50,5(.99) 8(0.7) 3x 6,4(0.5) HRU x 8(0.3),(0.48) 4,(.6) 44,4(.74) 68(.68) 3(.) 4(0.94) 4(0.94) 4,5(.) 38,5(.5) 77(3.03) Name ype ort size Ordering number Weight [kg (Ib)] M late H03-REK ,30 (0.87) late H03-REK-06 G3/8 G3/8 G/ late H03-REK-06-S SE 8 SE 8 SE ,35 (0.694) 3

24 Inlet, late H03-REK-07/-(S) /( ) - with sealing rings M YE G 3 (0.9) 3 (0.9) SE 8 (0.7) (0.83) xm6/(0.47) 5,5(0.6) 48(.89) 4,5(.),5(0.49) 5,6 (0.) 50,5(.99) 8(0.7) 3x 6,4(0.5) HRU x 8(0.3),(0.48) 4,(.6) 44,4(.74) 68(.68) 3x,4(0.49) 3(.) 4(0.94) 4(0.94) 4,5(.) 38,5(.5) 77(3.03) End late H03-REK with sealing rings 5,8 (0.3) x,4(0.48) x 6,4/ DEE 5 (0.5/DEE 0.),(0.48) 4,(.6) 44,4(.74) 56(.30) 3 x 6,4 HRU (0.5 HRU) 4(0.94) 4(0.94) 6,5(0.5) 4(0.55) 6(.40) 4 Name ype ort size Ordering number Weight [kg (Ib)] M late+seals H03-REK-07 G3/8 G3/8 G/ ,34 (0.69) late+seals H03-REK-07-S SE 8 SE 8 SE late+seals H03-REK ,35 (0.98)

25 Sandwich late H03-REK-M/-(S) /( ) M Flow in direction M Z Z Z3 L Z Z Z Z Z3 os. Name ype Valve Dimensions - M/-(S) Max. L [mm (in)] Weight [kg (Ib)] Data sheet Ordering number Sandwich plate + seals H03-REK-M ,35(0.76) H03-REK-M-S Z ressure valve S-3 77 (3.03) H 543 Z Directional valve SDE-3 70 (.75) H 404 Z3 lug 3/4-6UNF 5 (0.0) Spare Seal kit- Square ring Standard - NR70 9,5 x,68 ( pcs.) Viton 9,5 x,78 ( pcs.) (.8) x,4( 0.49) 3x 6,4(0.5) HRU x 8(0.3),(0.48) 4,(.6) 44,4(.74) 56(.0) 5,8 (0.3) 0(0.79) 40(.57) 4(0.94) 4(0.94) 77(3.03) 30,5(.0) 6,5(0.5) 8(.0) Cavity: 3/ way 3/4-6 UNF Measuring output: M...G/4, (SE 4 ) M 0(0.79) 5

26 Sandwich late H03-REK-M/-(S) /(934400) Flow in direction M M Z Z Z3 L Z Z Z Z Z3 os. Name ype Max. L [mm (in)] Weight [kg (Ib)] Data sheet Ordering number Sandwich late + seals H03-REK-M ,35(0.76) H03-REK-M-S Z ressure reducing valve S-3 77 (3.03) H 543 Z Directional valve SDE-3 70 (.75) H 404 Z3 lug 3/4-6UNF 5 (0.0) Spare Seal kit- Square ring Standard - NR70 9,5 x,68 ( pcs.) Viton 9,5 x,78 ( pcs.) Valve Dimensions - M/-(S) 30(.8) x,4( 0.49) 3x 6,4(0.5) HRU x 8(0.3) 56(.0) 0(0.79) 40(.57) 77(3.03) 30,5(.0) 6,5(0.5) 8(.0) 0(0.79),(0.48) 4,(.6) 44,4(.74) 5,8 (0.3) 4(0.94) 4(0.94) M Cavity: 3/ way 3/4-6 UNF Measuring output: M...G/4, (SE 4 ) 6

27 Sandwich late H03-REK-MC CONNECION -, - Z Z REK-03 Z L Z Z Z Z Z os. Name ype max L [mm (in)] Weight [kg (Ib)] Data sheet Ordering number lock + seals H03-REK-MC 0,379 (0.835) Z ressure valve SR- 49,5 (.95) H 5063 Z lug /- 3/4-6UNF 7,5 (0.9) Spare Seal kit- Square ring Standard - NR70 9,5 x,68 ( pcs.) Viton 9,5 x,78 ( pcs.) , 44,4 34, 9 5,8 x,4 /,4 56 3x 6,4 RŮCHOZÍ x , Cavity: /-3/4-6 UNF 7

28 Sandwich late H03-REK-MD CONNECION -, - Z REK-03 Z Z Z Z Z L Z3 Z3 Z Z Z Z3 Z os. Name ype Max. L [mm (in)] Weight [kg (Ib)] Data sheet Ordering number Sandwich late + seals H03-REK-MD 0,378(0.833) Z ressure valve SR- 49,5 (.95) H 5063 Z Directional valve SDE- 70 (.75) H 4040 Z3 lug 3/4-6UNF 7,5 (0.9) Spare Seal kit- Square ring Standard - NR70 9,5 x,68 ( pcs.) Viton 9,5 x,78 ( pcs.) Valve Dimensions - MD 34(.34) 9(0.75) 5,8 (0.3) HRU 3x 6,4(0.5) x,4(0.49) x 8(0.3),(0.48) 4,(.6) 44,4(.74) 56(.0) 0(0.79) 40(.57) 4(0.94) 4(0.94) 77(3.03) 38,5(.5) 0(0.79) Cavity: / way 3/4-6 UNF 8

29 Sandwich late H03-REK-M/-(S) /(934400) Z-Z3 Z-Z3 REK-03 Z L Z Z Z3 Z Z3 Z Z Z3 os. Name ype Max. L [mm (in)] Weight [kg (Ib)] Data sheet Ordering number Sandwich late + seals H03-REK-M ,407(0.897) H03-REK-M-S Z Directional valve SD3E- 70 (.75) H 4043 Z Directional valve SDE- 70 (.75) H 4040 Z3 lug 3/4-6UNF 7,5(0.9) Spare Seal kit- Square ring Standard - NR70 9,5 x,68 ( pcs.) Viton 9,5 x,78 ( pcs.) Valve Dimensions - M/-(S) 34(.34) 5,8 (0.3) x,4(0.49) 3x 6,4(0.5) HRU x 8(0.3),(0.48) 4,(.6) 44,4(.74) 56(.0) 34(.34) 0(0.79) 40(.57) 4(0.94) 4(0.94) 77(3.03) 38,5(.5) 0(0.79) 0(0.79) Cavity: / way 3/4-6 UNF Connecting threads:,...g/4, (SE6) 46(.8) 5,5(0.6) 9

30 Sandwich late H03-REK-M/-(S) /( ) REK-03 Z-Z3 L Z4-Z5 Z-Z3 3 Z-Z3 Z4-Z5 Z4-Z5 3 Z-Z3 os. Name ype Max. L [mm (in)] Weight [kg (Ib)] Data sheet Ordering number Sandwich late +seals H03-REK-M ,53(.73) H03-REK-M-S Z Overcentre valve SO-Q3 47 (.85) H 500 Z Overcentre valve SO5-Q3/I 47 (.85) H 50 Z3 Overcentre valve SO5-Q3/I 47 (.85) H 50 Z4 Check valve SC5H-Q3/I 7 (0.7) H 57 Z5 Check valve SCC5H-Q3/I 7 (0.7) H 5 Spare Seal kit- Square ring Standard - NR70 9,5 x,68 ( pcs.) Viton 9,5 x,78 ( pcs.) Valve Dimensions - M/-(S) 5,8 (0.3) 34(.34) 3x 6,4(0.5) HRO x,4(0.49) x 8(0.3),(0.48) 4,(.6) 44,4(.74) 56(.0) 34(.34) 9,5(0.77) 4(0.94) 4(0.94) 7(.06) 40(.57) 5(.00) (0.87) 0(0.79) 30(.8) 36(.4) 0(4.0) Cavity: M0x,5 30

31 Sandwich late H03-REK-M Z-Z5 Z5 L Z4 Z Z Z Z 3 Z3 Z3 Z Z Z3 Z4 Z4 Z5 Z5 os. Name ype Max. L [mm (in)] Weight [kg (Ib)] Data sheet Ordering number Sandwich late +seals H03-REK-M 0,45(0.95) Z Flow valve VSV-J-3/4-6UNF (0.87) H Z Directional valve SD3E- 70 (.75) H 4043 Z3 Directional valve SDE- 70 (.75) H 4040 Z4 lug 3/4-6UNF 7,5 (0.9) Z5 lug 3/4-6UNF 3 (0.) Spare Seal kit- Square ring Standard - NR70 9,5 x,68 ( pcs.) Viton 9,5 x,78 ( pcs.) DKR 000N7033 7,65 x,68 ( pcs.) Valve Dimensions - M 5,8 (0.3) 34(.34) 56(.0) 3x 6,4(0.5) HRU x 8(0.3) x,4(0.49),(0.48) 3,(0.5] 4,(.6) 44,4(.74) 34(.34) 0(0.79) 9(0.35) 4,4(0.57) 0(0.79) 40(.57) 4(0.94) 4(0.94) 39(.54) 77(3.03) Cavity: / way 3/4-6 UNF 3

32 Mounting ngle 7(0.8) 6,5(0.7) (0.08) 6,4(0.5) 4(0.55) 6,5(0.69) 6 7,5(0.30) 6,75(0.7) 8(0.7) 4(0.98) 4(0.94) (0.08) sada Kit (0.08) (0.08) 6,5(0.69) 48(.89) 6(.40) Name ightening torque Ordering number / Kit Kit Mounting ngle ( pc.) old M6 x ( pcs.) Washer 6 ( pcs.) (8.85) [Nm (Ibf-ft)] Spare arts - lates Seal kit - Square ring Name Dimensions, number Ordering number Standard - NR70 9,5 x,68 ( pcs.) Viton 9,5 x,78 ( pcs.)

33 M6 OLS/SUDS LENGH for Horizontal ssembly (Mu - (8.85)[Nm (Ibf-ft)]) L = (L x X) + (L x X) + (L3 x X) + Y L = total length (to 00 cm screw bolt hereinafter) L= 40 mm (.57 in) (Horizontal plate with lenght 40 mm (.57 in)) L= 3 mm (. in) (Horizontal plate with lenght 3 mm (. in)) L3= 4 mm (0.55 in) (End plate) X = Number of plates of the given width (see page 3) Y = 4 mm (0.55 in) for bolts - dditional length of bolt thread used for nuts mounting 5 mm (0.98 in) for studs - dditional length of bolt thread used for nuts mounting L [mm (in)] Ordering number / Kit L [mm (in)] Ordering number / Kit -OLS - SUDS 45 (.77) (7.835) (.36) (7.99) (.953) (8.8) (3.346) (8.6) (3.937) (8.89) SUDS 9 (9.05) (4.9) (9.9) (4.57) (9.646) (4.9) (9.96) (5.4) (0.078) (5.35) (0.97) (5.630) (0.433) (5.787) (0.748) (5.984) (0.984) (6.8) (.99) (6.47) (.64) (6.575) (.8) (6.77) (.65) (7.047) (.36) (7.36) (.59) (7.638) (.93) Note: Select the bolt or screw length according to the nearest dimension available in the table. 33

34 Vertical ssembly llustrative Figure a) b) End late lock lock Extension late Extension late Measuring late V03-REK-05 VERICL SSEMLY - 4 Section Extension late ype Cavity Connecting threads Ordering number age Description (to select the studs) V03-REK L=40 mm (.57 in) ilot Operated Check Valve VJR5-03 Dn 03 Katalog H L=40 mm (.57 in) Vertical Sandwich late with Valves V03-REK-MC / - 3/4-6UNF L=40 mm (.57 in) VSVJ-03/MC Mx L=40 mm (.57 in) VSVJ-03/MD Mx L=40 mm (.57 in) Cover late -, orts V03-REK-0, - G/ L=6 mm (.0 in) V03-REK-0-S, - SE 6 40 L=6 mm (.0 in) V03-REK-03, - G/4 - side L=6 mm (.0 in) V03-REK-03-S, - SE 6 - side L=6 mm (.0 in) V03-REK-04, - G3/8 - side L=6 mm (.0 in) Measuring late -, orts V03-REK-05, - G/ L=6 mm (.0 in) 34

35 Extension late V03-REK Extension late 4,4(.63),4(0.45) 4x 5,3(0.) HRU 4,(0.6) 40(.58),8(0.86) = = 30(.8) 5,8(.08) 6(.40) 4,(0.6),4(0.05) x 5,3(0.) x,4(0.49) he application of a extension plate is required only in vertical assembly situation in case no ilot Operated Check valve is used and is required a free space for electrical connectors of REK directional valve (see example of assembly in picture). Name ype ort size Ordering number Weight [kg (Ib)] Extension late+ seals V03-REK ,89 (0.436) 35

36 ilot Operated Check Valve H 507 VJR5-03/M VJR5-03/M VJR5-03/MC os. Name ype Weight [kg (Ib)] Data sheet Hydraulic lock + seals VJR5-03/Mx 0, (0.44) H 507 Valve Dimensions Ordering number Spare Seal kit Square ring O-ring Standard - NR70 9,5 x,68 ( pcs.) 4,47 x,78 ( pcs.) Viton - 9,5 x,78 ( pcs.) 4,47 x,78 ( pcs.) (.40) 5.8 (.079) 4. (.68) 4. (0.6).4 (0.449).8 (0.858) 0 (0.787) 0.9 (0.49) 4. (0.6) 30 (.8) 40 (.575) 4x 5.3 (0.09) 5 (0.59) 36

37 Sandwich late V03-REK-Mx Z(Z) Z L Z Z(Z) Z Z C Z(Z) Z(Z) Z Z os. Name ype Max. L [mm (in)] Weight [kg (Ib)] Data sheet Ordering number Sandwich plate +seals V03-REK-Mx 0,349 (0.769) Z ressure valve SR- 78 (3.07) H 5063 Z lug 3/4-6UNF 7,5 (0.9) Spare Seal kit- Square ring Standard - NR70 9,5 x,68 ( pcs.) Viton 9,5 x,78 ( pcs.) Valve Dimensions - MC 4,(0.6) 30(.8),4(0.45) 30(.8) 4,4(.63) 5,8(.08) 0(0.79) 40(.57) 4,(0.6) 0(0.79),8(0.86) 0,9(0.43) 5(0.59) x 5,3(0.) 5(0.59) x,4(0.49) 30(5.) 4x 5,3(0.) HRU 4,(0.6) 34,5(.36) 6(.40] Cavity : / -3/4/6UNF 37

38 Sandwich late V03-REK-Mx Screw-in Cartridge hrottle Valve with ypass Check Valve M L M Z Z Z MC Z Z Z os. Name ype Max. L [mm (in)] Weight [kg (Ib)] Data sheet Ordering nummer Sandwich plate+seals V03-REK-MC 0,36(0.795) Z Flow valve VSV (only model -, - J) (0.43) H 53 Z lug VSV/ Mx (0.43) Spare Seal kit- Square ring Standard - NR70 9,5 x,68 ( pcs.) Viton 9,5 x,78 ( pcs.) Valve Dimensions - MC 4,4(.63) 5,8(.08) 40(.58) 4,(0.6) 0(0.79),8(0.86) 0,9(0.43) 30(.8) 0(0.79),4(0.05) 30(.8),4(0.45) 5(0.59) x 5,3(0.) x,4(0.49) 6(4.56) 5(0.59) 4x 5,3(0.) HRU 4,(0.6) 7,5(.08) 6(.40) Cavity: Mx 38

39 Sandwich late V03-REK-Mx Screw-in Cartridge hrottle Valve with ypass Check Valve ME L MF Z Z Z MD Z Z Z os. Name ype Max. L [mm (in)] Weight [kg (Ib)] Data sheet Ordering nummer Sandwich plate +seals V03-REK-MD 0,36(0.795) Z Flow valve VSV (only model -, - J) (0.43) H 53 Z lug VSV/ Mx (0.43) Spare Seal kit- Square ring Standard - NR70 9,5 x,68 ( pcs.) Viton 9,5 x,78 ( pcs.) Valve Dimensions - MD 30(.8) 4,(0.6),4(0.45) 30(.8) 4,4(.63) 5,8(.08) 0(0.79) 40(.57),4(0.05) 0(0.79),8(0.86) 0,9(0.43) 5(0.59) x 5,3(0.) x,4(0.49) 6(4.56) 5(0.59) 4x 5,3(0.) HRU 4,(0.6) 7,5(.08) 6(.40] Cavity: Mx 39

40 Cover late V03-REK-0- /(S) /( ) V03-REK-0 V03-REK-0-S (0.47),4(0.06) 40(.57) 6(.0) x 5,3(0.) 30(.8) x,4(0.49) 6(.40),8(0.86) 0,9(0.43) 4,(0.6) 4,(0.6) 5(0.59) 4x 5,3(0.) HRU V03-REK-0,4(0.45) 30(.8) 5,8(.08) V03-REK-0-S,8(0.86) 0,9(0.43) 4,(0.6) 4,(0.6) 5(0.59) 4x 5,3(0.) HRU,4(0.45) 30(.8) 5,8(.08) Connecting threads: :,... G/4 (SE6) Name ype ort size Ordering number Weight [kg (Ib)] 40 Cover plate + seals V03-REK-0 G/4 G/ V03-REK-0-S SE 6 SE ,7 (0.379)

41 Cover late V03-REK-03-/(S) /( ),8(0.86) 0,9(0.43) 4x 5,3(0.) HRU 30(.8),(0.83),4(0.45) 3(0.5) 6(.0) 4,(0.6) 30(.8) 5,8(.08),4(0.05) 3(0.5) 5(0.59) x 5,3(0.) x,4(0.49) 95(3.74) 5(0.59) Connecting threads:,... G/4 (SE 6) Cover late V03-REK ,8(0.86) 0,9(0.43) 4x 5,3(0.) HRU 30(.8),(0.83),4(0.45) 3(0.5) 6(.0) 4,(0.6) 30(.8) 5,8(.08),4(0.05) 3(0.5) 5(0.59) x 5,3(0.) x,4(0.49) 95(3.74) 5(0.59) Connecting threads:,... G 3/8 Name ype ort size Ordering number Weight [kg (Ib)] V03-REK-03 G/4 G/ Cover plate +seals 0,3 (0.89) V03-REK-03-S SE 6 SE Cover plate +seals V03-REK-04 G3/8 G3/ ,77 (0.390) 4

42 Measuring late V03-REK ,8(0.86) 0,9(0.43) 4x 5,3(0.) HRU 30(.8) 4,(0.6),(0.83),4(0.45) 30(.8) 5,8(.08) 3(0.5),4(0.05) 6(.0) 3(0.5) 5(0.59) x 5,3(0.) x,4(0.49) 95(3.74) 5(0.59) Connecting threads:,... G/4 Name ype ort size Ordering number Weight [kg (Ib)] Measuring plate +seals V03-REK-05 G/4 G/ ,77 (0.390) Spare arts - lates Seal kit - Square ring Name Dimensions, number Ordering number Standard - NR70 9,5 x,68 ( pcs.) Viton 9,5 x,78 ( pcs.) M5 SCREWS LENGH for Vertical ssembly (Mu - 5(3.69) [Nm (Ibf-ft)]) L [mm ( in)] RGO-HYOS s.r.o CZ Vrchlabí tel.: info.cz@argo-hytos.com L = (L x X) + L + 9 L = total length L= 40 mm (.57 in) (Vertical plates with hight 40 mm (.57 in)) L= 6 mm (.0 in) (Vertical plates with hight 6 mm (.0 in)) X = Number of plates of the given width (see page 3) Ordering number/kit (4x bolts) 75 (.95) (4.57) (6.0) Note: Select the bolt or screw length according to the nearest dimension available in the table. 4 Subject to alteration without!