Solenoid System KNURLED NUT TOP CORE GUIDE TUBE PLUNGER
|
|
- Marilynn Lester
- 5 years ago
- Views:
Transcription
1
2 EVI 7 S8 Solenoid System COIL The EVI7 S8 system by AMISCO includes a wide range of solenoid operators designed for pneumatic valves. All solenoids of this system have the guide tube with a diameter of 8 mm and the plunger with a diameter of 7 mm. The system is designed for use with air. Please contact Amisco for use with other media. All given information are subjected to changes without notice. KNURLED NUT TOP CORE GUIDE TUBE PLUNGER THREAD M12X0,5 COIL The coil is available both in 22 mm and in 30 mm size for increased performances. Types, power and other characteristics are described in the following pages. All coils feature: heat resistant bobbin moulded with 30% glass filled thermoplastic polyester material class H wire 200 C according to IEC built-in magnetic yoke made by low carbon iron encapsulation with high quality specially designed glass filled nylon. The use of other materials is possible upon special agreements. All coils are rated to class F and to IP 65 (with connector) or IP67 for the flying lead version. The coil is designed and constructed in accordance to EN and VDE 0580 and it is suitable for industrial ambient conditions. For use in special ambients with high humidity, please, take contact with Amisco. The coil is also in conformity with 94/9/EC ATEX for electrical apparatus of group II, category 3 (Ex na II 3 GD T4 o T5). OPERATOR Plunger and core are made by a magnetic stainless steel specially designed for solenoid applications. The guide tube is made with brass (stainless steel is possible upon special agreement). The plunger is normally equipped with NBR rubber seals. Other materials like FKM are available upon request. The armature assembly is designed for more than 50x10 6 cycles. COMPLETE SOLENOID OPERATOR The coil is fastened to the plungerguide tube by means of a knurled nut for ease of change over without interrupting the pneumatic circuit. The plungerguide tube is fixed to the valve body by means of a M12x0.5 thread. The suggested interface dimensions of the valve body are shown on the right side. Any change to the prescribed dimensions can effect the performances of the solenoid operator. 1
3 SOLENOID SYSTEMS for 3/2 way normally closed and normally open valves Coil EVI 7/8 Characteristics DC AC (50 Hz) AC (60 Hz) Electrical termination: Rated power DC W 5.5 Terminals AMP 6.3x0.8 Inrush power AC VA width 11 mm Rated power AC VA Code: 0708S... Coil temperature rise C Copper temperature rise C Coil EVI 30/8 Characteristics DC AC (50 Hz) AC (60 Hz) Electrical termination: Rated power DC W 4 Terminals DIN 43650A Inrush power AC VA (Bottom ground) Rated power AC VA Code: 3008D... Coil temperature rise C Copper temperature rise C Operator S8 Characteristics DC AC (50 Hz) AC (60 Hz) 3/2 way NC Inlet orifice Ø mm Exhaust orifice Ø mm Code: 08F... Working pressure bar /2 way NO Inlet orifice Ø mm (inlet from the top) Working pressure bar Code: 08F... Note: Voltage tolerance: ± 10% Temperature range: 10 C +50 C Duty cycle: 100% Standard voltages: Other voltages on request VAC VDC For different orifice sizes and pressures contact AMISCO. 2
4 EVI 7/8 EVI 30/8 3
5 COIL CODING SPECIFICATIONS CODE: X X 9 9 Y K * * TYPE 07 = EVI 7 30 = EVI 30 COIL BORING 08 = 8 mm ELECTRICAL CONNECTION S = AMP 6,3x0,8 D = DIN A SUPPLY CURRENT A = Alternating current (A.C.) D = Direct current (D.C.) R = Rectified alternating current NOMINAL VOLTAGE Example: 024 = 24V 220 = 220 V EVI 7/8 WINDING CODE Nominal Voltage Power Winding Code 12VDC 5.5W 02 24VDC 5.5W 02 24VAC 6.5VA VAC 6.5VA VAC 7.5VA 01 EVI 30/8 WINDING CODE Nominal Voltage Power Winding Code 12VDC 4W 05 24VDC 4W 05 24VAC 4VA VAC 4VA VAC 5VA 01 Alternative possibilities for CUSTOMER LOGO MARKING ZN = Standard - no logo AM = Standard + Amisco logo... = customer specifications 4
6 EXAMPLES OF MAIN APPLICATIONS 3/2 NC 3/2 NO 3/2 OPERATOR 5
7 OPERATOR CODING SPECIFICATIONS CODE: X X X A A A A A R 9 C Z K TYPE 08F = Thread DRAWING NUMBER 3/2 NC /2 NO SUPPLY CURRENT A = Alternating current D = Direct current FUNCTION 3 = 3/2 way FUNCTION C = Normally closed O = Normally open SEALS E = EPDM - V = FKM N = NBR FASTENING NUTS (Note: tightening torque max 0.6 Nm) FASTENING SYSTEM N = Without fastening system. Fastening nuts to be ordered separately as below. Plastic knurled nut Cod Plastic knurled nut for protected exhaust Cod Aluminium knurled nut Weavy washer Ø 8 DIN 137 type A Cod Cod
8 AMISCO S.p.a. Via Piaggio, Paderno Dugnano (Mi) Italy Tel Fax Rev. 3/2012
Solenoid System FLANGE MOUNTING VERSION
EVI 9S Solenoid System COIL The EVI 9S system by AMISCO includes a wide range of solenoid operators designed for pneumatic valves. All solenoids of this system have the guide tube with a diameter of 8
More informationEVI 5 S13 Solenoid System
EVI 5 S13 Solenoid System The EVI5 S13 system by AMISCO includes a wide range of solenoid operators designed for pneumatic valves. All solenoids of this system have the guide tube with a diameter of 13
More informationSolenoid System. The coil is also in conformity with 94/9/EC ATEX for electrical apparatus of group II, category 3 (Ex na II 3 GD T4 or T5).
EVI 7 S9 Solenoid System The EVI7 S9 system by AMISCO includes a wide range of solenoids, coils and operators, designed for pneumatic valves. All solenoids of this system have the guide tube with a diameter
More informationValve: brass guiding tube plunger and core made by a magnetic stainless steel specially designed for solenoid applications polyester valve body
22mm & 3mm Pneumatic Pilot Valve Systems In order to meet the growing demand of the pneumatic industrial automation, AMISCO offers a complete range of pneumatic solenoid pilot valves with 22 mm and 3 mm
More information15 mm Pilot Valve. More technical specifications are reported in the following pages. 1
15 mm Pilot Valve The 15 mm pilot valve has been designed and developped by Amisco as a logical evolution of the traditional product range manufactured for the pneumatic market. The 15 mm solenoid valve
More informationAPPLICATION OF SYSTEM 8
System 8 System 8 The name System 8 stands for a modular system of solenoid coils, armature systems, solenoid operators and solenoid valves. The diameter of the armatures of all valve components is approimately
More informationSystem 6. ü ( System 6
System 6 ü www.nassmagnet.com ( +9 511 676-0 System 6 The name System 6 stands for a modular system of solenoid coils, armature systems, solenoid operators and solenoid valves. The diameter of the armatures
More informationSystem 6. Solenoid Coils Armature Assemblies Valve Systems
Solenoid Coils Armature Assemblies Valve Systems a Kft. i r á g n u H t e n nass mag Precision Controls Kft. since 0 Nass Controls LP Nass Magnet GmbH Introduction.........................................
More informationSystem 8. Solenoid Coils Armature Assemblies Valve Systems. Nass Controls LP Nass Magnet GmbH Precision Controls Kft.
Solenoid Coils Armature Assemblies Valve Systems Nass Controls LP Nass Magnet GmbH Precision Controls Kft. Introduction......................................... Page 4-5 Solenoid Coil Width 22 mm Connection
More informationSolenoid coils VACF Type codes
Solenoid coils VACF Type codes VACF B B2 1A Type VACF Solenoid coil, F series Solenoid coil type A B Width 30 mm, for 8 mm armature tube Width 22 mm, for 8 mm armature tube A1 Connection pattern type A,
More informationSystem 13. ü ( System 13
System ü www.nassmagnet.com ( +9 676-0 System The name System stands for a modular system of solenoid coils, armature systems, solenoid operators and solenoid valves. The diameter of the armatures of all
More information2/2-way Solenoid Valve with servo diaphragm, G 3/8 - G 2
2/2-way Solenoid Valve with servo diaphragm, G 3/8 - G 2 Type 6281 can be combined with... User friendly - one solenoid for all orifices Waterhammer free and low noise NC or NO Manual override optional
More informationSeries PD directly operated solenoid valves
> Series PD solenoid valves CATALOGUE > Release 8.7 Series PD directly operated solenoid valves New /-way Normally Closed (NC) Note: all Series PD /-way solenoid valves are basically in DC. To operate
More informationData sheet. 2-way solenoid valves with Clip-on coils for neutral liquids and gases. January 2003 DKACV.PD.200.K B1472
Data sheet 2-way solenoid valves with Clip-on coils for neutral liquids and gases January 200 DKACV.PD.200.K.22 520B472 2 DKACV.PD.200.K.22 Danfoss A/S 0-200 Contents 2-way solenoid valves with Clip-on
More informationSeries PD directly operated solenoid valves
> Series PD solenoid valves CATALOGUE > Release 8.8 Series PD directly operated solenoid valves /-way - Normally Closed (NC) Please note that all Series PD solenoid valves are supplied with direct current
More informationMINI-SOLENOID VALVES ISO (CNOMO, size 15) interface direct operated, pad mounting body connector size 15
MINI-SOLENOID VALVES ISO 58 (CNOMO, size 5) interface direct operated, pad mounting body connector size 5 NC / Series 0 FEATURES Compact, monobloc solenoid pilot valve with spade-plug connector type EN
More informationSOGEAC SOLENOID VALVE NASS MAGNET: SYSTEM 8. s.r.l.
With pleasure we introduce on the Italian market SYSTEM 8, produced NASS MAGNET of solenoid valve that thanks to their modularity give the possibility of a wide range of easy solutions. The solenoid valve
More informationFlow. group *2) G1/4 1, , B G1/ , B /4 NPT , B N/en
/ poppet valves electromagnetic actuated, directly controlled G /4, G / or /4 NPT Working from 0 bar up Short switching times Suited for fine vacuum down to,33 0 - mbar For a.c. solenoid systems with integrated
More informationOperating pressure (bar) kv factor (m 3 /h) *3)
/ poppet valves (stainless steel) electromagnetic actuated, directly controlled G /8, G /4 or /4 NPT Working from 0 bar up Assembled free of oil and grease Suited for fine vacuum down to,33 0 - mbar For
More informationMiniature coil (3W) encapsulated in synthetic material. Connection with 3-pin DIN type B plug. Degree of protection IP 65.
NAMUR 1/4 & 1/2 High Flow valves for actuator control Catalogue 4921/GB INDEX General Information...page 2 G 1/4 Series...page 4 G 1/2 Serie...page 6 Accessories...page 8 TECHNICAL DATA Function : Manual
More information2/2-way Solenoid Valve with servo diaphragm, G 3/8 - G 2
2/2-way Solenoid Valve with servo diaphragm, G 3/8 - G 2 Type 6281 can be combined with... User friendly - one solenoid for all orifices Waterhammer free and low noise NC or NO Manual override optional
More informationIndirect servo-operated 2/2-way solenoid valves Type EV220W 10 - EV220W 50, NBR and EPDM versions
Data sheet Indirect servo-operated 2/2-way solenoid valves Type EV220W 10 - EV220W 50, NBR and EPDM versions EV220W is a range of compact indirect servo- operated 2/2 way solenoid valves with connections
More information2/2 or 3/2-way Solenoid Valve, with pivoted armature and isolating diaphragm
2/2 or 3/2-way Solenoid Valve, with pivoted armature and isolating diaphragm Lockable manual override as standard For liquid, gaseous and aggressive media Long service life, even in non-lube conditions
More information2/2 or 3/2-way Solenoid Valve, with pivoted armature and isolating diaphragm
/ or 3/-way Solenoid Valve, with pivoted armature and isolating diaphragm Type 0330 can be combined with Lockable manual override as standard For liquid, gaseous and aggressive media Long service life,
More informationDirect-acting 3/2 way plunger valve
Direct-acting 3/2 way plunger valve Direct-acting, compact valve with diameter of up to DN 2.5 Vibration-proof, bolted coil system Banjo threaded connection for direct mounting on pneumatic valves Type
More information3/2-, 5/2- and 5/3-way Solenoid Valves for process pneumatics
/-, 5/- 5/-way Solenoid Valves for process pneumatics Type 658 stard High flow-rate capacity Reduced power consumption Single or manifold mounting stard Type 658/659 can be combined with... Stard-, EEx
More informationServo-operated 2/2-way solenoid valves Type EV220A
Data sheet Servo-operated 2/2-way solenoid valves Type is a compact servo-operated 2/2-way solenoid valve program, especially designed for use in machines and equipment with limited space. Features and
More informationSeries P directly operated solenoid valves
> Series P solenoid valves CATALOGUE > Release 8.7 Series P directly operated solenoid valves 3/-way NC and NO. The solenoid valves can be mounted on a single base (with M5 ports) as well as on manifolds
More information3/2, 5/2, 5/2 bistable and 5/3 way pneumatic solenoid valve
3/2, 5/2, 5/2 bistable and 5/3 way pneumatic solenoid valve Type 6518 Type 6519 Type 6518/6519 can be combined with... Single or block mounting Suitable for outdoor and chemical atmospheres Suitable for
More informationType 2511/12. Type Type 2030 Cable plug. ASI cable plug. Dosing control. General technical data Orifice Type 6518
3/2-, 5/2- and 5/3-way Solenoid Valves for process pneumatics Type 658 standard standard High flow-rate capacity Reduced power consumption Single or manifold mounting Standard-, EEx m and EEx i versions
More informationMFH MOFH JMFH JMFDH NVF3 MUFH VOFD VOFC VSNC VUVS
Solenoid coils Solenoid coils Product range overview Version Type For valve series Page/ Internet MFH MOFH JMFH JMFDH NVF3 MUFH VOFD VOFC VSNC VUVS F solenoid coil MSF VACF 3 N solenoid coil VACN-N 6 N
More information3/2-, 5/2- and 5/3-way Solenoid Valves for process pneumatics
/2-, 5/2-5/-way Solenoid Valves for process pneumatics Type 658 stard High flow-rate capacity Reduced power consumption Single or manifold mounting stard Type 658/659 can be combined with... Stard-, EEx
More information2/2-way Solenoid Valve for liquids and gases
2/2-way Solenoid Valve for liquids and gases Type 6213EV can be combined with... Coupled spring diaphragm system opened without differential pressure Waterhammer free and low noise HP00 version with increased
More informationBody: Seat disc: Anod. aluminium body NBR. Connection / Orifice Flow factors Temperature values ( C)
Parker Lucifer Data Sheet 22062004 General information Lucifer ref.: 341N31 Global ref.: 7341NAKBJNM0 Housing ref.: 2995 Coil ref.: 481865 Protection class: Assembly wt. (g): 510 Body: Seat disc: Anod.
More informationVALVES ISO 5599/1, SERIES IPV-ISV
VALVES ISO 5599/, SERIES IPV-ISV The assembly surface dimensions of ISO, ISO2 and ISO 3 valves are to ISO5599-. They are available in the 5-way versions with 2 and 3 positions and with pneumatic or solenoid
More informationElectrically operated spool valve. The manual override is detent and is operated by screw driver.
Valves > electrically operated valves > Series M-07 Technical details Connection G1/ Nominal size Temperature range Medium Series M-07 page Materials 9 mm -10 C... +70 C Filtered, oil-free and dried compressed
More informationSOLENOID VALVES AND PNEUMATIC VALVES
S E R I E S P Directly operated mini-solenoid valves Series P 3/ way N.C. or N.O. Ports M5 (for single base) Cartridge ø 3 and 4 (for manifold) Note: All the serie P electrovalves are basic in DC. For
More informationFeatures PNEUMAT IC VALVES. Pneumatic valves Vip - Pneumatic coaxial valve GENERAL FEATURES CONTROL MEDIA OPERATING MEDIA
OMAL S.p.a. Via Ponte Nuovo, 11-25050 Rodengo Saiano (BS) ITALY Phone +39 0308900145 - Fax +39 0308900423 Booked in the Enterprise Register of: Brescia number 1661640175 Share capital completely deposited:
More informationExplosion-proof Solenoids ATEX. II 2 G / II 2 D EEx dm IIC T4, T5, T6. Catalogue 8735/GB. Maximum photo
Explosion-proof Solenoids II 2 G / II 2 D EEx dm IIC T4, T5, T6 Catalogue Maximum photo ATEX Explosionproof solenoids with flameproof enclosure/encapsulation "dm" According to ATEX directive 94/9/EC and
More informationDirectional Control Valve Series D3W Soft Shift
Characteristics The D3W is a 3-chamber, electrically controlled 4/3 or 4/ way directional control valve. It is activated directly by solenoids with screwed in wet pin armature. The soft shifting of this
More informationFunction. Orifice (mm) NBR (Perbunan) 0 EPDM 1 FKM (Viton) 2 FFKM (Kalrez) / O-ring FKM 4
Working from 0 bar up Short switching times Suited for fine vacuum down to 1,33 10-3 mbar Assembled oil and grease-free For a.c. solenoid systems with integrated rectifier (40 to 60 Hz) These solenoid
More informationSolenoid Operator 0516 / 1216
nass magnet GmbH Edition no. 2 Eckenerstraße 4-6 2007-01-10 D-30179 Hannover Rev.2 070110 Solenoid Operator 0516 / 1216 Operating Instructions NN 8220 126 and EC Declaration of Conformity Dear Customer!
More informationnickel-plated brass - PBT technopolymer HNBR, FKM stainless steel
CATALOGUE > Release 8.8 > Series A solenoid valves Series A directly operated solenoid valves /-way - Normally Closed (NC) and Normally Open (NO) 3/-way - Normally Closed (NC) and Normally Open (NO)»»
More information3/2-way Rocker Solenoid Valve for pneumatic systems
3/-way Rocker Solenoid Valve for pneumatic systems EEx ia versions Direct-acting High cycling rate Reduced power consumption Type 6104 can be combined with... Sub-base connection Approvals: Type 654 Servo-assisted
More information300 SERIES DRESSER NUT VALVES PENTAIR CLEAN AIR SYSTEMS
DRESSER NUT VALVES PENTAIR CLEAN AIR SYSTEMS CONSTRUCTION FEATURES VALVE Cover Diecast aluminium (anodised) Body Diecast aluminium (anodised) Pilot base Brass (chromed) Pilot Diaphragm NBR Bolts and screws
More information3/2-way Small Solenoid Valve, G 1/8 - G 1/4 and sub-base
3/2-way Small Solenoid Valve, G 1/8 - G 1/4 and sub-base Sub-base Direct-acting, normally closed and normally open Brass and stainless steel body Electrical cable plug Form A With or without manual override
More informationSOLENOID VALVES PIV.M 15 mm
SOLENOID VALVES PIV.M mm / NC/NO direct control microvalves Possible assembly on single and multiple bases Monostable manual actuation as standard Assembly in any position Operation with filtered lubricated
More informationnickel-plated brass - PBT technopolymer HNBR, FKM stainless steel
CATALOGUE > Release 8.7 > Series A solenoid valves Series A directly operated solenoid valves /-way, 3/-way NC and NO. Monostable - bistable (with magnetic memory) Ports M5 - G1/8 - R1/8 - cartridge ø4
More informationSolenoid Operator 0513 / 1213
nass magnet GmbH Run Nr. 5 Eckenerstraße 4-6 24.10.2006 D-30179 Hannover Rev. 5 061024 Solenoid Operator 0513 / 1213 Operating Instructions NN 8220 112 and EC Declaration of Conformity Dear Customer! In
More informationSeries MI-01, MI-02, MI-03
Valves > standardized valves > electrically operated > Series MI-01, MI-02, MI-03 ISO 99/1, Size 1 to 3 Technical details Series Connection MI-01, MI-02, MI-03 ISO 99/1 Nominal size Temperature range Medium
More informationMINI-SOLENOID VALVES direct operated subbase mounted, CNOMO (15 mm width) connector size 15
MINI-SOLENOID VALVES direct operated subbase mounted, CNOMO ( mm width) connector size / Series 0 FEATURES Low consumption (0,W) Compact, monobloc solenoid pilot valve with spade-plug connector type AMP,8x0,
More informationTechnical Data Sheet
Technical Data Sheet Type 52 2/2-way solenoid valve NC - Valve normally closed (as standard) NO - Valve normally open (as option) Direct operated piston design valve. No differential pressure is necessary
More information3/2-way Solenoid Valve, direct-acting, NC or NO
3/2-way Solenoid Valve, direct-acting, NC or NO Electrical connection cable plug, Form A With or without manual override as standard Threaded port and sub-base s Impulse optional Type 6014 can be combined
More informationDirect-acting 2/2-way plunger valve
Direct-acting 2/2-way plunger valve Type can be combined with Direct-acting and compact valve up to diameter of DN 6.0 Vibration-proof, bolted coil system Increased leak-tightness with welded plunger guiding
More informationK Series 3 Way Direct Acting Balanced Poppet Solenoid Valve
Ex d Ex m IP5 Series 3 Way Direct Acting Balanced Poppet Solenoid Valve DB2S-M2C \ Ex d IIC with Integral Stainless \ Steel Junction Box. \ Valve. \ Manual Override, Option M2. J77072S-M2 \ Ex m II NASS
More informationType Modular Water Valve System servo-assisted; variable and extendable. 2/2 way; DN mm; 1 up to 7 bar Advantages / Benefits
2/2 way; DN 10-13 mm; 1 up to 7 bar Advantages / Benefits Reduction of Cost of Ownership up to 60% Modular system design Block assembly by lock technology Easy change between distributing and collecting
More informationHigh Flow Valve Actuation Range. NAMUR Valves G1/4" & G1/2" Piped Valves G1/4" & G1/2" Banjo Valves G1/8" & G1/4"
31-37 High flow NAMUR valves G1/ and G1/ aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding High Flow Valve Actuation
More informationProportional solenoid valve for pneumatic application V PR M
Proportional solenoid valve for pneumatic application 3 Product group V PR M Function 2/2 NC Proportional direct-acting Armature pressure tight up to 16 bar static pressure Short correction times High
More informationCOILS, CONNECTORS, SOLENOID VALVES
COILS, CONNECTORS, SOLENOID VALVES 117 10 mm solenoids Solenoid valve 10 mm 00.441.0 Tension 24V DC ±10% Temperature range -5 C...+60 C (23 F... 140 F) Power 0.5... 1 W Operating pressure 0... 7 bar (0...
More information2/2-way Solenoid Valve with servo diaphragm
2/2-way Solenoid Valve with servo diaphragm Type 5282 can be combined with... Pivoted armature pilot drive with manual override Magnetic drive completely isolated from fluid by diaphragm Circuit function
More informationSolenoid valve 2/2 way N.C. With pilot control
Solenoid valve 2/2 way N.C. With pilot control 21H7KV1 21H8KV1 PRESENTATION: S.V. with pilot control for interception of fluids compatible with the construction materials. A minimum operational pressure
More information3/2 Directional Control Valves Direct solenoid operated poppet valves Internal thread G1/4, 1/4-18 NPT or flanged with NAMUR interface
3/ Directional Control Valves Direct solenoid operated poppet valves Internal thread G1/4, 1/4-18 NPT or flanged with NAMUR interface Suitable for instrumental air, neutral gaseous and liquid fluids and
More informationNAMUR Technical details
Valves > standardized valves > electrically operated > Series MN-06 NAMUR Technical details Connection Series Nominal MN-06 size Temperature range Medium G1/4, Namur 6 mm -10 C... +70 C Filtered, oil-free
More information200 SERIES THREADED VALVES PENTAIR CLEAN AIR SYSTEMS
THREADED VALVES PENTAIR CLEAN AIR SYSTEMS Lock nut DESCRIPTION The is a range of diaphragm valves suitable for dust collector applications, in particular for reverse pulse-jet filter cleaning of filter
More informationMECAIR 300 SERIES DRESSER NUT VALVES CLEAN AIR SOLUTIONS PRODUCT LEAFLET
300 SERIES DRESSER NUT VALVES CLEAN AIR SOLUTIONS GENERAL CHARACTERISTICS CONSTRUCTION FEATURES VALVE FLUIDS PRESSURE RANGE Filtered air and oil free Standard Nitrile: 20 C/+80 C Optional Viton: 30 C/+200
More informationSolenoid Valves & Accessories. Incorporating Solenoid Valves in. Custom Products. Solenoid Operated. Custom Products
PNEUMADYNE, INC. Catalog 24 Phone 763-559-177 Fax 763-559-547 Incorporating Solenoid Valves in Custom Products For over 3 years, manufacturers have relied on Pneumadyne for innovative solutions to their
More informationDirectional Control Valve Series D1VW
Characteristics The NG6 directional control valve series D1VW provides high functional limits up to 8 l/min in combination with a very low, energy-saving pressure drop. A wide variety of spool options
More informationType 6213 EV, 6281 EV
Type 6213 EV, 6281 EV 2/2-way solenoid valve 2/2-Wege-Magnetventil Électrovanne 2/2 voies Operating Instructions Bedienungsanleitung Manuel d utilisation 1 OPERATING INSTRUCTIONS The operating instructions
More information2/2-way and 3/2-way Normally Closed (NC) and Normally Open (NO)
Series CFB solenoid valves /-way and 3/-way Normally Closed (NC) and Normally Open (NO)»» Solenoid valves for air and water»» Great reliability over time, even in heavy working conditions The valve function
More informationVALVES ISO 5599/1, SERIES IPV-ISV
The assembly surface dimensions of ISO1, ISO2 and ISO 3 valves are to ISO5599-1. They are available in the 5-way versions with 2 and 3 positions and with pneumatic or solenoid actuation. TECHNICAL DATA
More information600/700 SERIES FLANGED VALVES PENTAIR CLEAN AIR SYSTEMS
FLANGED VALVES PENTAIR CLEAN AIR SYSTEMS CONSTRUCTION FEATURES VALVE Cover Body Pilot Diaphragm Bolts and screws Diaphragm backing disk Diaphragm spring Diecast aluminium (anodised) Diecast aluminium (anodised)
More information2/2-way Compact Solenoid Valve, G 1/4 - G 1/2
2/2-way Compact Solenoid Valve, G 1/4 - G 1/2 Stainless steel body Type 6027 Compact can be combined with Direct-acting, normally closed Brass and stainless steel body Electrical connection cable plug
More informationDIRECTIONAL CONTROL VALVES CETOP 3/NG6
CETOP 3/NG06 STANDARD SPOOLS CH. I PAGE 0 AD.3.E... CH. I PAGE AD.3.E...J* CH. I PAGE 2 AD3.XS... CH. I PAGE 3 AD3.XD... CH. I PAGE 4 AD.3.V... CH. I PAGE 5 AD.3.L... CH. I PAGE 6 OTHER OPERATOR CH. I
More informationSOLENOID VALVES FOR REFRIGERATING SYSTEMS
SOLENOID VALVES 17 SOLENOID VALVES FOR REFRIGERATING SYSTEMS APPLICATIONS The solenoid valves, shown in this chapter, are classified Pressure accessories in the sense of the Pressure Equipment Directive
More informationSOLENOID VALVES AND PNEUMATIC VALVES
A S E R I E S Catalogue 001 Directly operated solenoid valves Series A / way, 3/ way monostable, stable (with magnetic memory) Ports M5, G1/8, cartridge ø 4 The Series A solenoid valves are of the directly
More informationType Operating Instructions. Bedienungsanleitung Manuel d utilisation. 2/2-way solenoid valve 2/2-Wege-Magnetventil Électrovanne 2/2 voies
Type 6027 2/2-way solenoid valve 2/2-Wege-Magnetventil Électrovanne 2/2 voies Operating Instructions Bedienungsanleitung Manuel d utilisation 1 OPERATING INSTRUCTIONS The operating instructions contain
More information97100 Inline 3/2, 5/2 & 5/3 spool valves electromagnetic actuated, indirectly controlled G 1/4, 1/4 NPT
97 Inline /, 5/ & 5/ spool valves electromagnetic actuated, indirectly controlled G /, / NPT For single and double operated actuators Crossover-free switching, switch-over function guaranteed even with
More informationDIRECT OPERATED SOLENOID PILOT VALVES Product Index
DIRECT OPERATED SOLENOID PILOT VALVES Product Index ports/positions Function pipe connections * - instant fittings O.D. (mm) w - internal thread (ØG) x - external thread (ØG) n - pad mount : - pad mount,
More informationNAMUR Technical details
Valves > standardized valves > electrically operated > Series KN-0, KN- NAMUR Technical details Connection Nominal size Series KN-0, KN- Temperature range Medium G1/4, Namur 6 mm -10 C... +70 C Filtered,
More information97100 NAMUR. Technical data
9700 NAMUR /2-, /2- and / Directional control valves Actuation: electromagnetic Indirectly controlled soft seal spool valves Port size: G /4, /4 NPT NAMUR Interface For single and double operated actuators
More information400 SERIES MANIFOLD MOUNT VALVES PENTAIR CLEAN AIR SYSTEMS
MANIFOLD MOUNT VALVES PENTAIR CLEAN AIR SYSTEMS CONSTRUCTION FEATURES VALVE Cover Body Pilot Diaphragm Bolts and screws Diaphragm backing disk Diaphragm spring Diecast aluminium (anodised) Diecast aluminium
More informationPneumatic Valve 4V100 Series
tic Valves Pneumatic Valve 4V100 4V100 Low power consumption exhaust for the pilot and main valve, small size, large flow, good appearance, flexible, can be integrated installation, high wear resistant
More informationDirect-acting 2/2- or 3/2-way pivoted armature valve
0330 Direct-acting 2/2- or 3/2-way pivoted armature valve Direct-acting, media-separated valve with diameter of up to DN 5 Maintenance-free pivoted armature technology Vibration-proof, block screwed coil
More informationProportional solenoid valve for pneumatic application V PR M
Proportional solenoid valve for pneumatic application 3 Product group V PR M Function / NC Proportional direct-acting Armature space pressure tight up to 16 bar static pressure High linearity Quick response
More informationGEMÜ 205 Electrically operated solenoid valve
Electrically operated solenoid valve Features Hermetic separation between medium and actuator In case of power failure operation possible by manual override Standard integral optical position indicator
More informationComplete Range of Movement Solutions
Complete Range of Movement Solutions A complete range of Movement Solutions are available from your Local Pirtek Centre. ISO & VDMA Pneumatic Cylinders Compact Cylinders Guided Cylinders Non-Standard Cylinders
More informationSolenoid coil for control in potentially explosive areas Type BZ
Data sheet Solenoid coil for control in potentially explosive areas Type BZ BZ is a solenoid coil with ATEX / IECEx approval, applicable for zone 1 and 2 Ex environments. The coils are designed to be used
More informationSOLENOID VALVES AND PNEUMATIC VALVES
9 S E R I E S Electropneumatically and pneumatically operated valves Series 9 Assembly with sub-base (ISO 5599/1 Standards) Sizes 1, and 3 001 The Series 9 electropneumatically or pneumatically operated
More informationMECAIR 200 SERIES THREADED VALVES CLEAN AIR SOLUTIONS PRODUCT LEAFLET
200 SERIES CLEAN AIR SOLUTIONS - 200 SERIES CONSTRUCTION FEATURES VALVE Lock nut DESCRIPTION COVER Diecast aluminium (anodised) BODY Diecast aluminium (anodised) PILOT BASE Aluminium (anodised) PILOT Stainless
More informationHERION SERIES Indirect solenoid actuated soft seal
HERION 9700 SERIES Indirect solenoid actuated soft seal spool valves with NAMUR interface /, 5/ - G/ For single and double acting actuators Crossover-free switching, switchover function guaranteed even
More informationFor mounting on subbase or footprint in accordance with CNOMO recommendation E 06620N Part numbers (and voltages) Voltage max. power consumption U nom
Intrinsically Safe Miniature Solenoid Valves Order/Technical Support Tel: (800) 6775 / FAX: (800) 677865 / www.crouzetusa.com 5/6 5 For mounting on subbase or footprint in accordance with CNOMO recommendation
More informationIntrinsically Safe Miniature Solenoid Valves
Intrinsically Safe Miniature Solenoid Valves 5 Order/Technical Support Tel: (800) 6775 / FAX: (800) 677865 / www.crouzetusa.com 5/6 Intrinsically safe miniature solenoid valves EEx ia T6 approval no. 9
More informationMN-06. Standardized valve series 3/2-way acc. to NAMUR, 750 Nl/min (0.762 Cv) Technical data for series. Order code MN HN-142
Standardized valve series 3/2-way acc. to NAMUR, 750 Nl/min (0.762 Cv) Technical data for series Order code -310-HN-142 Series and function Standard coil 1) (with plug socket 28-ST-01) 141 = 12 V DC, 4.2
More informationPilot Operated Directional Control Valves Series D31DW, D31NW, D*1VW
Characteristics The pilot operated valves are available in 4 sizes: D31DW NG10 (standard) D31NW NG10 (high flow) D41VW NG16 D81VW NG5 (for port diameter up to 6 mm) D91VW NG5 (for port diameter up to 3
More information4/3, 4/2 proportional directional valves solenoid operated (for open loop control)
/, / proportional directional valves solenoid operated (for open loop control) RE -/7. Replaces: RE7/.7 / Type L (LCP) Size Series Maximum operating pressure bar [ psi] Nominal flow rated l/min [.7 gpm]
More informationType EV224B. Servo-operated 2/2-way solenoid valves for high pressure air. Data sheet
Data sheet Servo-operated 2/2-way solenoid valves for high air Type EV224B EV224B for compressed air, is a high indirect servo-operated 2/2-way solenoid valve with working up to 40 bar, medium temperature
More informationDL /116 ED SOLENOID OPERATED DIRECTIONAL CONTROL VALVE COMPACT VERSION SERIES 10 SUBPLATE MOUNTING ISO p max 320 bar Q max 125 l/min
41 330/116 ED SOLENOID OPERATED DIRECTIONAL CONTROL VALVE COMPACT VERSION SUBPLATE MOUNTING ISO 4401-05 p max 320 bar Q max 125 l/min MOUNTING INTERFACE OPERATING PRINCIPLE ISO 4401-05-04-0-05 (CETOP 4.2-4-05-320)
More information2/2 or 3/2 way direct acting rocker solenoid valve
2/2 or 3/2 way direct acting rocker solenoid valve With isolating diaphragm Ultra low dead volume Type 6126 can be combined with... High back-pressure tightness Normally closed, normally open or universal
More informationDL /118 ED SOLENOID OPERATED DIRECTIONAL CONTROL VALVE COMPACT VERSION SUBPLATE MOUNTING ISO p max 280 bar Q max 50 l/min
41 211/118 ED DL3 SOLENOID OPERATED DIRECTIONAL CONTROL VALVE COMPACT VERSION SUBPLATE MOUNTING ISO 4401-03 p max 280 bar Q max 50 l/min MOUNTING SURFACE OPERATING PRINCIPLE ISO 4401-03-02-0-05 (CETOP
More informationEx m Solenoid Operator Type 0519
nass magnet GmbH Eckenerstrasse 4-6 D-30179 Hannover Doc. No. 113-720-0002 Revision No. 2 01.06.2015 Ex m Solenoid Operator Type 0519 Operating Instructions Dear Customer! To ensure the function and for
More information