Installation Instructions

Transcription

1 Installation Instructions for /" top spud Urinals Certified to comply with: ASSE 07 ANSI/ASME A.9. ADA Compliant 0 AS America, Inc. MODEL NUMBERS 0.0 FOR TOP SPUD APPLICATIONS CLOG RESISTANT Self-cleaning piston valve prevents clogging and reduces maintenance. OPERATING PRESSURE: Overall Range: 0- psi ** Recommended: psi (flowing) - 80 psi (static) FLOW REQUIREMENT: 0gpm (7.9 L/min). Flush valves include sweat solder kit. **Water pressure over 80 psi is not recommended with most plumbing fixtures NOTE TO INSTALLER: Please give this manual to the customer after installation. To learn more about American Standard Faucets visit our website at: or U.S. customer's us at: faucetsupport@americanstandard.com For Parts, Service, Warranty or other Assistance, please call (In Canada: ) (In Toronto Area only: )

2 Thank you for selecting American-Standard...the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Products Are Water Tested At Our Factory. Some Residual Water May Remain In The Valve During Shipping.. Remove the Flush Valve items from the carton. The illustration below shows all items after they have been removed from the carton. Some items may be packaged partially assembled to other items.. Flush Valve Assembly. Down Tube and Vacuum Breaker. Spud Coupling Nut and Washers. Spud Flange. Sweat Solder Adapter. Cover Tube 7. Wall Escutcheon 8. Supply Stop 9. Installation Instructions CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE Installation Instructions for /" top spud Urinals Certified to comply with: ASSE 07 ANSI/ASME A.9. ADA Compliant 0 AS America, Inc. MODEL NUMBERS 0.0 FOR TOP SPUD APPLICATIONS CLOG RESISTANT Self-cleaning piston valve prevents clogging and reduces maintenance. OPERATING PRESSURE: Overall Range: 0- psi ** Recommended: psi (flowing) - 80 psi (static) FLOW REQUIREMENT: 0gpm (7.9 L/min). Flush valves include sweat solder kit. **Water pressure over 80 psi is not recommended with most plumbing fixtures NOTE TO INSTALLER: Please give this manual to the customer after installation. To learn more about American Standard Faucets visit our website at: or U.S. customer's us at: faucetsupport@americanstandard.com For Parts, Service, Warranty or other Assistance, please call (In Canada: ) (In Toronto Area only: )

3 Fig. Roughing-in Dimensions 08mm-mm (-/" to -/") FINISHED WALL 8mm-7mm (-/-") GENERAL DESCRIPTION: for /" Top Spud Fixtures Exclusive, self cleaning piston-operated flush valve. SUPPLY DN 9mm (/" I.P.S. For /" Top Spud) *CRITICAL LEVEL /" VACUUKM BREAKER SHOWN mm () (Min.) 9mm (-/") mm (-/") -C-L- -C-L- OPERATING PRESSURE: Overall Range: 0- psi ** Recommended: 0 psi (flowing)- 80 psi (static) FLOW REQUIREMENT: 0gpm (7.9 L/min). **Water pressure over 80 psi is not recommended with most plumbing fixtures *Note: The Critical Line (-C-L-) on Vacuum Breaker must typically be " (mm) minumim above fixture. Consult Codes for details. Right or Left Hand Installation See (Section 8) for converting Flush Valve to Left Hand Installation. RECOMMENDED TOOLS; Fig. Fig Teflon Tape Flat Blade Screwdriver (For adjusting Supply Stop) Adjustable Wrench Tape Measure Hacksaw Tubing Cutter File For Sweat Connection; Solder and Torch.mm Hex Wrench.mm Hex Wrench 0' PRIOR TO INSTALLATION Note: Prior to installing the Selectronic Flush Valve the following items must be installed.. Urinal. Drain line. Water supply line IMPORTANT: All plumbing must be installed in accordance with applicable codes and regulations. Water supply lines must be sized to provide an adequate volume of water for each fixture. Flush all water lines prior to operation (See Step ). Dirt and debris can cause flush valve to run continuously. With the exception of Supply Stop Inlet, DO NOT use pipe sealant or plumbing grease on any valve component or coupling! Protect the chrome or special finish on the Flushometer. DO NOT USE toothed tools on finished surfaces to install or service these valves. Also see Care and Cleaning section of this manual. This product contains mechanical and/or electrical components that are subject to normal wear. These components should be checked on a regular basis and replaced as needed to maintain the valve s performance.

4 INSTALL SWEAT SOLDER ADAPTER; Fig. CAUTION Turn water supplies off before beginning Note: Install Optional Sweat Solder Adapter (Supplied) for copper pipe supply line. Fig.. Fig. FINISHED WALL A Fig.a CENTER LINE OF FIXTURE SPUD. Measure the distance (A) from the finished wall to the center of the inlet spud on the fixture.. Cut the supply pipe -/" (A-B=C) shorter then the measurement taken in Step. File any rough edges off the end of the supply pipe. (A-B)= C FILE EDGES CLEAN B mm (-/). Clean the end of the supply pipe. Push the threaded Adapter on until it is seated against the internal stop. Sweat the Adapter to the pipe. ADAPTER SOLDER ADAPTER INSTALL COVER TUBE, WALL ESCUTCHEON and SUPPLY STOP; Fig.. Measure from finished wall to first thread of Adapter or threaded supply pipe (dimension X ). Cut COVER TUBE () to length (X). Apply Teflon Tape to the threaded end of the Adapter or supply pipe. Fig. a.. Push the COVER TUBE () into the WALL ESCUTCHEON (). Slide both onto the SUPPLY PIPE (). Fig. b.. Push the COVER TUBE () in to expose the threads of the supply pipe. Fig. c. With a wrench thread the SUPPLY STOP () onto the SUPPLY PIPE (). Align and tighten. Fig. c.. Pull COVER TUBE () against SUPPLY STOP () and push WALL ESCUTCHEON () against finished wall. INSTALL DOWN TUBE AND VACUUM BREAKER; Fig. Fig. Fig. a Fig. b Fig. c Fig. X FINISHED WALL TEFLON TAPE X. Place the SPUD FLANGE () over the spud on the Fixture.. Thread SPUD COUPLING NUT () onto Spud. Make sure SEAL WASHER () and FRICTION WASHER () are installed. Do not tighten fully.. Insert the DOWN TUBE () into the SPUD COUPLING NUT () and push it down. Note: If cutting Down Tube () to size, note that Critical Line (C/L) on Vacuum Breaker must typically be " (mm) minumim above fixture. Consult Code for details. /" TOP SPUD

5 INSTALL FLUSH VALVE; Fig. a & b. As shown in Fig. a, insert the side INLET FLANGE () on the FLUSH VALVE () into the SUPPLY STOP (). Lubricate the INLET FLANGE O-RING () with water if necessary. Lightly tighten COUPLING NUT (). Fig. a. Important: Do not use lubricants (other than water) or any type of thread sealing paste or tape. Fig. a. Align the FLUSH VALVE () (Fig. b) directly above the DOWN TUBE (7) and VACUUM BREAKER COUPLING NUT (). Make sure that GASKET (0) is installed. Note: There is a + mm, ( + /) tolerance for the mm (-/) dimension. Fig. b.. Pull the DOWN TUBE (7) up to meet the threaded FLUSH VALVE CONNECTION (8) and hand tighten the VACUUM BREAKER COUPLING NUT (). Align all components of the flush valve assembly. Fig. b.. Lightly tighten the COUPLING NUT () connection first, then the VACUUM BREAKER COUPLING NUT () and finally the SPUD COUPLING NUT (9). Once alligned correctly, use a wrench to tighten couplings to make water tight connections. Fig. b. Fig. b mm, + mm (-/)( + /) FLUSH OUT SUPPLY LINES; Fig. 7. Remove COVER () from SUPPLY STOP (). Make sure supply stop is closed. Fig. 7. Remove FLUSH VALVE CAP (). Pull out PISTON (). Replace FLUSH VALVE CAP () and tighten.. With a flat blade screwdriver open SUPPLY STOP (). to flush line of any debris or sediment.. Close SUPPLY STOP (). Remove FLUSH VALVE CAP (). Replace PISTON (). Replace FLUSH VALVE CAP () and tighten. COUNTER-CLOCKWISE OPENS CONTROL STOP REMOVE COVER CLOCKWISE CLOSES CONTROL STOP

6 ADJUST SUPPLY STOP; Fig. 8 IMPORTANT: To avoid overflowing, the SUPPLY STOP () must never be opened to the point where the flow from the valve exceeds the flow capacity of the fixture. The fixture and drain must be able to handle a continuous flow in case of a flush valve failure. Valve is designed to provide stated flush volume with a 0 GPM flow rate.. Remove COVER () from SUPPLY STOP ().Turn on water supply / turn to / turn(ccw) and test for leaks. Note: Unit may flush for approximately to 0 sec. when water is first turned on.. Actuate the FLUSH VALVE by pulling handle down.. Adjust SUPPLY STOP () after each flush until the stated flush volume is achieved, no splashing occurs and the fixture is properly cleansed.. When adjustment is complete, replace COVER () and tighten to ensure vandal-resistance. Fig. 8 CLOCKWISE CLOSES CONTROL STOP REMOVE COVER COUNTER-CLOCKWISE OPENS CONTROL STOP 7 HOW TO RETROFIT OUR VALVE; Fig. 9 (Replaces Industry Standard Manual and Electronic Valves) Note: In most Retrofits the wall escutcheon, supply stop, cover tube and vacuum breaker do not have to be replaced. If these items do need replacement they must be purchased separately or order the complete flush valve assembly from American Standard.. Remove COVER () from SUPPLY STOP () if installed. Fig. 9. Fig. 9 Fig. 9a Fig. 9b CLEAN CONNECTIONS. Turn water supply off. Fig. 9.. Loosen SPUD COUPLING NUT (). Unthread COUPLING NUT () and VACUUM BREAKER COUPLING NUT (). Remove FLUSH VALVE (). Fig. 9a.. Clean all threaded connections before installing the new flush valve. Fig. 9a.. Refer to Sections, and to complete the retrofit installation. Fig. 9b. LEFT OR RIGHT HAND INSTALLATION; Fig. 0 8 Fig. 0 Right or Left Hand Installation. The FLUSH VALVE can be installed either as a right or left hand installation.. Orientate the FLUSH VALVE as shown in Fig. 0 to desired position for a left or right hand installation. Left Hand Right Hand

7 for Top Spud Urinals MODEL NUMBERS 0.0 M A CAP SEAL M A CUP SEAL M999D A PISTON ASSEMBLY M A HANDLE ASSEMBLY OPTIONAL ADJUSTABLE TAILPIECE (Purchased Separately) M98-000A (8-/" to 9-/" Rough-in) M98-000A (7-/" to 8-/" Rough-in) M98-000A (-/" to 7-/" Rough-in) M98-000A (-/" to -/" Rough-in) M A ADJUSTABLE TAILPIECE (-/" to -/" Rough-in) M A VACUUM BREAKER REPAIR KIT M9-000A /" VACUUM BREAKER ASSEMBLY M9-000A /" INLET PIPE ASSEMBLY M A STAMPED FLANGE M A COVER TUBE M A SWEAT ADAPTER M90-000A /" SUPPLY STOP M A CAP M9-000A /" SPUD ASSEMBLY HOT LINE FOR HELP For toll-free information and answers to your questions, call: (800) -90 Weekdays 8:00 a.m. to :00 p.m. EST IN MEXICO IN CANADA (TORONTO ) Weekdays 8:00 a.m. to 7:00 p.m. EST Product names listed herein are trademarks of AS America, Inc. AS America, Inc. 0