INSTALLATION INSTRUCTIONS

Size: px

Start display at page:

Download "INSTALLATION INSTRUCTIONS"

Lisa Dickerson
5 years ago
Views:

1 INSTALLATION INSTRUCTIONS Accessory TRAILER HITCH Application 2011 ODYSSEY Publications No. AII Issue Date SEP 2010 PARTS LIST Trailer Hitch Kit P/N 08L92-TK8-100 Trailer Hitch Harness Kit P/N 08L91-TK8-100 Trailer hitch Control unit harness Socket harness Ball mount Hitch pin Control unit bracket Hitch pin clip Control unit Receiver cover EPT sealer 6 Hex bolts 11 Wire ties 6 Plain washers 2 Flange bolts 5 Clips Fuse (10A) Bumper edge trim 2 Fuses (7.5A) 2010 American Honda Motor Co., Inc. All Rights Reserved. AII (1009) 08L92-TK of 17

2 ATF Cooler Kit P/N RV0-305 ATF Cooler ATF Hose (265 mm) ATF Hose (335 mm) ATF Hose (295 mm) 3 Washer-bolts (6 x 12 mm) 4 Hose clamps TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Ratchet 6 mm and 12 mm Sockets Trim Tool Set (T/N SOJATP2014) Diagonal cutters Torque wrench Drill 3 mm and 10 mm Drill bits Blanket Eye protection (safety goggles, face shield, etc.) Isopropyl alcohol Shop towel Air saw (Snap on AT192A) Pushpin File 10 mm Open end wrench Hex wrench Masking tape Pliers Illustration of the Trailer Hitch Installed on the Vehicle Hose spacer (5 A/T) Mirror hang-tag TRAILER HITCH CONTROL UNIT SOCKET AD 2 of 17 AII (1009) 2010 American Honda Motor Co., Inc. All Rights Reserved.

3 INSTALLATION 4. Remove the driver s sliding door sill trim (five clips, six retaining tabs and two hooks). Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 4 RETAINING TABS 2 HOOKS NOTE: Allow the engine and transmission to cool down before installing the ATF cooler. Be careful not to damage the rear bumper or other finished surfaces of the body. Make sure to install the backup sensors before installing the trailer hitch. Do not damage the body paint finish. 1. Make sure you have the anti-theft code for the audio unit and navigation system (if equipped), then write down the radio station presets. 2. Remove the air duct (two clips). CLIP RETAINING TAB DRIVER S SLIDING DOOR SILL TRIM 5 CLIPS 5. Remove the rear trim panel. Using a shop towel and pliers, remove two threaded hooks BD AIR DUCT TRIM PANEL PLIERS AD 2 THREADED HOOKS 3. Disconnect the negative cable from the battery. THREADED HOOK SHOP TOWEL AD 2010 American Honda Motor Co., Inc. All Rights Reserved. AII (1009) 3 of 17

4 Pull away the weatherstrip from around the rear trim panel. Gently pull out on the rear trim panel to release eight clips and four retaining tabs, and remove the rear trim panel. WEATHERSTRIP Pull away. 8 CLIPS Fold down the third row seat. Pull away the weatherstrip from around the rear of the driver s side rear trim panel. Pull away the door opening seal from around the front of the driver s side rear trim panel. Gently pull out on the driver s side rear trim panel to release ten clips and ten retaining tabs. Unplug the vehicle connector, and remove the driver s side rear trim panel. If the vehicle is equipped with other vehicle connectors, unplug the vehicle connectors. WEATHERSTRIP Pull away. CONNECTOR CONNECTORS If equipped. 10 CLIPS 4 RETAINING TABS TRIM PANEL 6. Remove the driver s side rear trim panel. Using a shop towel and pliers, remove the threaded hook BD RETAINING TABS SIDE TRIM PANEL DOOR OPENING SEAL CD Pull away. THREADED HOOK THREADED HOOK SIDE TRIM PANEL PLIERS SHOP TOWEL AD 4 of 17 AII (1009) 2010 American Honda Motor Co., Inc. All Rights Reserved.

5 7. On each side of the rear bumper, attach masking tape to the rear bumper, taillight, and rear fender as shown. On each side, release nine retaining tabs. 9 RETAINING TABS TAILLIGHT FENDER MASKING TAPES BD 8. Remove the rear bumper. Remove six self-tapping screws, four hex bolts, and five clips BD Have an assistant help you when removing the rear bumper. Place the rear bumper on a blanket after removal. 6 SELF-TAPPING SCREWS 5 CLIPS 4 HEX BOLTS CD BD 2010 American Honda Motor Co., Inc. All Rights Reserved. AII (1009) 5 of 17

6 Routing the Socket Harness and Control Unit Harness 9. On the outside of the vehicle at the rear panel, locate and discard the vehicle grommet. 13. Route the socket harness along the vehicle harness and secure it to the vehicle harness with three wire ties. SOCKET GROMMET HOLE SOCKET GROMMET PANEL 3 WIRE TIES OUTSIDE INSIDE SOCKET GROMMET Discard. SOCKET PANEL BD 10. Route the 4-pin connector side of the socket harness from the outside of the vehicle. Install the socket harness grommet into the rear panel. 11. Inside in the vehicle, use isopropyl alcohol on a shop towel to thoroughly clean the rear panel where the EPT sealer will attach. 14. Get the control unit harness. Plug the control unit harness 4-pin connector to the socket harness 4-pin connector. SOCKET 4-PIN CONNECTOR TRIM 4-PIN CONNECTOR AD TRIM PANEL SOCKET TRIM AD EPT SEALER AD 12. Attach the EPT sealer to the rear panel as shown. 6 of 17 AII (1009) 2010 American Honda Motor Co., Inc. All Rights Reserved.

7 15. Remove one vehicle ground bolt from the vehicle ground terminal. If the vehicle is equipped with accessory backup sensors, go to step 18; if not, go to step 20. With Accessory Backup Sensors 18. Unplug the accessory backup sensor harness 14-pin connector from the rear fuse box. VIEWED FROM ACCESSORY BACKUP SENSOR 14-PIN CONNECTOR FUSE BOX 14-PIN CONNECTOR GROUND BOLT GROUND TRIM TERMINAL GROUND TERMINAL AD 16. Secure the control unit harness ground terminal and the vehicle ground terminal with the vehicle ground bolt removed step in Route the control unit harness along the vehicle harness and secure the 4-pin connectors and control unit harness to the vehicle harness with six wire ties. 6 WIRE TIES SIDE TRIM 14-PIN CONNECTOR SIDE TRIM FUSE BOX AD 19. Plug the accessory backup sensor harness 14-pin connector into the control unit harness 14-pin connector. 4-PIN CONNECTORS AD 2010 American Honda Motor Co., Inc. All Rights Reserved. AII (1009) 7 of 17

8 20. Plug the control unit harness 14-pin connector to the 14-pin opening in the rear fuse box. VIEWED FROM FUSE BOX 22. Remove one fuse box bolt from the rear fuse box. FUSE BOX 14-PIN OPENING FUSE BOX DRIVER S SIDE TRIM PANEL OPENING 14-PIN CONNECTOR AD SIDE TRIM FUSE BOX BOLT Reuse AD 23. Install the control unit to the vehicle panel with the fuse box bolt removed in step Insert the control unit onto the control unit bracket. FUSE BOX CONTROL UNIT CONTROL UNIT BRACKET SIDE TRIM FUSE BOX BOLT Reuse AD AD 8 of 17 AII (1009) 2010 American Honda Motor Co., Inc. All Rights Reserved.

9 24. Plug the control unit harness 12-pin connector into the control unit. SIDE TRIM 12-PIN CONNECTOR CONTROL UNIT 27. Install two 7.5A fuses into the rear fuse box as shown. If two 7.5A fuses are already installed in the fuse box in the slots, go to step 28. VIEWED FROM FUSE BOX SIDE TRIM 7.5A FUSE OPENING CONTROL UNIT FUSE BOX WIRE TIE AD 25. Secure the control unit harness to the vehicle harness with one wire tie. 26. Install one 10A fuse into the rear fuse box as shown. If a 10A fuse is already installed in the fuse box in the slot, go to step A FUSE Installing the Trailer Hitch 28. Release the rubber mount from the muffler. NOTE: Be careful not to damage the muffler DD VIEWED FROM FUSE BOX SIDE TRIM RUBBER MOUNT 10A FUSE OPENING FUSE BOX 10A FUSE MUFFLER AD AD 2010 American Honda Motor Co., Inc. All Rights Reserved. AII (1009) 9 of 17

10 29. Install the trailer hitch to the vehicle frame with six plain washers and six hex bolts. NOTE: Have an assistant help you when installing the trailer hitch. Torque the hex bolts: 80 N m (8.1 kgf m, 59 lbf ft). 32. While wearing eye protection, drill the front two pierced marks of the rear bumper. First drill with a 3 mm drill bit, and finish with a 10 mm drill bit. Remove any burrs. DRILL 3 mm 10 mm DRILL BIT FRAME 2 MARKS BD TRAILER HITCH 33. Drill the rear two pierced marks of the rear bumper. First drill with a 3 mm drill bit, and finish with a 10 mm drill bit. 6 PLAIN WASHERS 6 HEX BOLTS BD 30. Reinstall the rubber mount to the muffler. 31. Inside the rear bumper, locate four scribe marks. Using a pushpin, pierce the center of each scribe mark on the rear bumper as shown. DRILL 3 mm 10 mm DRILL BIT 2 MARKS PUSHPIN 2 SCRIBE MARKS AD PUSHPIN 2 SCRIBE MARKS AD 10 of 17 AII (1009) 2010 American Honda Motor Co., Inc. All Rights Reserved.

11 34. Using an air saw, cut the rear bumper along the scribe line as shown. Remove any burrs. 36. Using a felt-tip pen, mark the centers of the bumper edge trim holes. Cut. FELT-TIP PEN SCRIBE LINE EDGE TRIM AIR SAW AD MARK MARK AD 35. Install the bumper edge trim to the rear bumper. 37. Remove the bumper edge trim. 38. Using a pushpin, pierce the two marks on the rear bumper. PUSHPIN EDGE TRIM BD MARK MARK AD 2010 American Honda Motor Co., Inc. All Rights Reserved. AII (1009) 11 of 17

12 39. While wearing eye protection, drill the rear bumper. First drill with a 3 mm drill bit, and finish with a 10 mm drill bit. Remove any burrs. 41. While wearing eye protection, use an air saw to cut the rear bumper along the scribe line as shown. Remove any burrs. AIR SAW SCRIBE LINE DRILL 3 mm 10 mm DRILL BIT MARK MARK AD Cut. 40. Attach the bumper edge trim to the rear bumper with two clips. Cut. SCRIBE LINE AIR SAW AD 2 CLIPS Supplied. EDGE TRIM EDGE TRIM AD 12 of 17 AII (1009) 2010 American Honda Motor Co., Inc. All Rights Reserved.

13 42. Secure the socket harness to the trailer hitch with two flange bolts. Make sure that the socket harness is in the correct position and orientation. 44. Reinstall the rear bumper. NOTE: Have an assistant help you when installing the rear bumper. 6 SELF-TAPPING SCREWS Reuse. TRAILER HITCH 2 FLANGE BOLTS SOCKET SOCKET CLIP CLIP Reuse. 2 CLIPS Reuse. CLIP Supplied. 2 CLIPS Supplied. CLIP Reuse. 4 HEX BOLTS Reuse CD 45. Secure the ball mount to the trailer hitch with the hitch pin and one hitch pin clip. TRAILER HITCH TRAILER HITCH BD 43. Secure the socket harness to the trailer hitch with the socket harness clip. TRAILER HITCH HITCH PIN HITCH PIN BALL MOUNT HITCH PIN CLIP AD 46. Check that all wire harnesses are routed properly and all connectors are plugged in. 47. Reinstall all removed parts. 48. Reconnect the negative cable to the battery. 49. Enter the customer s anti-theft code for the radio and navigation system (if equipped), and reset the radio station presets. 50. Reset the clock American Honda Motor Co., Inc. All Rights Reserved. AII (1009) 13 of 17

14 Installing The AT Cooler NOTE: Before starting work, allow the ATF and the surrounding parts to cool. 51. Remove the front grille cover (refer to the service manual). 52. Remove the front bumper (refer to the service manual). 53. Remove the front splash shield (refer to the service manual). 54. Remove the left headlight assembly (refer to the service manual). 55. Remove the A/C condensor upper mount brackets (refer to the service manual). 56. Remove the bolts from the power steering line. 57. Detach the clips, then remove the left air guide. LEFT AIR GUIDE 58. Cut the left air guide along the lines as shown. Then remove and discard the cut piece. BOLT 9.8 N m (1.0 kgf m, 7.2 lbf ft) Cut here 59. Install the left air guide. 14 of 17 AII (1009) 2010 American Honda Motor Co., Inc. All Rights Reserved.

15 60. Assemble the ATF cooler. NOTE: Apply ATF when installing the hoses. When connecting the hoses, make sure to insert the hose until it hits the bulge of the pipe. Install each hose clamp with the tip of the clip located 7 mm from the edge of the hose. Get the ATF hoses, the ATF cooler and the two hose clamps from the kit. Attach the 335 mm hose (6AT:295 mm hose) to the upper pipe of the ATF cooler with a clamp. Attach the 265 mm hose to the lower pipe of the ATF cooler with a clamp. 5AT: Remove the hose that connects the ATF pipe B comp and ATF pipe C assy, and put plugs in both ATF pipe B comp and ATF pipe C assy to prevent leaks. ATF COOLER UPPER PIPE ATF HOSE 295 mm (6AT) 7±1 mm ATF HOSE 335 mm (5AT) ATF PIPE B COMP ATF PIPE C ASSY 6AT: Remove the hose that connects the ATF filter and ATF pipe C assy, and put plugs in both ATF filter and ATF pipe C assy to prevent leaks. ATF PIPE C ASSY ATF COOLER LOWER PIPE ATF HOSE 265 mm 61. Route the hoses installed on the ATF cooler through the hole cut in the left air guide, and fit the ATF cooler into place on the bulkhead. Install the three washerbolts from the kit through the ATF cooler into the threaded holes into the front bulkhead. Tighten the bolts securely. ATF FILTER 6 x12 mm WASHER-BOLT 9.8 N m (1.0 kgf m, 7.2 lbf ft) 62. Raise the vehicle on a lift American Honda Motor Co., Inc. All Rights Reserved. AII (1009) 15 of 17

16 63. Connect the ATF hose. NOTE: When installing the hose clamps, make sure they do not interfere with the surrounding parts. 5AT: Remove the plug from the ATF pipe B comp, and connect the ATF cooler upper hose. Install the hose clamp. Remove the plug from the ATF pipe C assy, and connect the ATF cooler lower hose. Install the hose clamp. ATF PIPE B COMP 7±1 mm 7±1 mm ATF COOLER LOWER HOSE ATF PIPE C ASSY 64. 5AT: Attach the hose spacer between the two hoses at the white paint on the ATF hose. ATF COOLER UPPER HOSE 6AT: Remove the plug from the ATF filter, and connect the ATF cooler upper hose. Install the hose clamp. Align the paint marks as shown. PAINT MARK ATF COOLER UPPER HOSE 7±1 mm ATF FILTER PAINT MARK HOSE SPACER 65. Install the power steering line mounting bolts. 66. Install the A/C condensor upper mount brackets (refer to the service manual). 67. Install the left headlight assembly (refer to the service manual). 68. Install the front splash shield (refer to the service manual). 69. Install the front bumper and the front grille cover (refer to the service manual). 70. Inspect the ATF fluid level and adjust as required. 71. Install the hang-tag around the rearview mirror. 16 of 17 AII (1009) 2010 American Honda Motor Co., Inc. All Rights Reserved.

17 Give a copy of this page to your customer Installing the Receiver Cover Whenever you remove the hitch pin clip, the hitch pin, and the ball mount, store them securely in the cargo area. Install the receiver cover into the opening at the end of the trailer hitch. When you reinstall the ball mount, store the receiver cover in the cargo area. RECEIVER COVER TRAILER HITCH AD Install the ball mount the trailer hitch using a hitch pin clip and hitch pin. TRAILER HITCH HITCH PIN HITCH PIN BALL MOUNT HITCH PIN CLIP AD After the first 600 miles (1,000 km) of towing, have your Honda Dealer re-check the tightness of the trailer hitch bolts American Honda Motor Co., Inc. All Rights Reserved. AII (1009) 17 of 17

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory TRAILER HITCH Application 2012 ODYSSEY Publications No. AII 46755 Issue Date SEP 2011 PARTS LIST Trailer Hitch Kit P/N 08L92-TK8-100 Trailer Hitch Harness Kit P/N 08L91-TK8-100