Illustrated guide to changing the mode of a Spektrum DX6 transmitter
|
|
- Eugenia Henry
- 5 years ago
- Views:
Transcription
1 Page 1 of 8 Illustrated guide to changing the mode of a Spektrum DX6 transmitter Purpose Follow this process if you want to change the mode of your Spektrum DX6 transmitter. You can change between mode 1 and mode 2. It would be better, of course, to buy the transmitter in the preferred mode in the first place, or to organise an exchange with your supplier. Warning This process will void your warranty. Fine soldering is required. (There's a nice soldering guide at ) Don't blame the author if something terrible happens. You could wreck your device, burn yourself, poison yourself with lead solder and soldering fumes, or blind yourself with spattering particles of molten solder. Things you'll need Your Spektrum DX6 transmitter Phillips-head screwdrivers Long-nose pliers or tweezers Soldering iron and solder Paper clip or wire 1 x 1k Ohm resistor - Virtually any power rating ought to do. I used a 1/4 watt metal film type, as shown here. Part A - Mechanical This part of the procedure swaps the springs and ratchets between the elevator and throttle sticks. Step 1: Remove the back cover Remove the battery. The battery wire connector pulls straight out. Remove the 6 screws on the back of the transmitter case, and gently lift off the back cover. You'll see something like this:
2 Page 2 of 8 This transmitter is in its original mode 2 condition. I want to change it into mode 1 operation. Each of the stick assemblies is like the other, but rotated 180 degrees. Step 2: Remove the throttle ratchet spring The ratchet spring is the piece of metal that makes the throttle click. Undo the screw and remove it.
3 Page 3 of 8 Notice that the ridged plastic part under the ratchet spring is lubricated. Step 3: Remove the elevator spring and spring arm Move the elevator stick and notice which parts inside the transmitter move. You'll see a spring move - that's the elevator spring. You'll see a plastic arm connected to the spring move too - that's the elevator spring arm.
4 Page 4 of 8 Use long-nose pliers to disconnect the spring from the spring arm. Note how the spring arm is restrained at the end opposite the spring. Remove the spring arm. Note how the spring is hooked onto a catch at the base of the stick assembly. Remove the spring. Step 4: Replace the throttle ratchet spring Put the ratchet spring onto the stick assembly you want to use for throttle. Do up the screw. I just used my finger to transfer some of the lubricant from one ratchet to the other. I wasn't sure that any of the lubricants I had on hand were safe for plastic. Step 5: Replace the elevator spring and spring arm Hook the elevator spring onto the lower catch assembly that you want to use for
5 Page 5 of 8 elevator. Hook a paper clip through opposite end of the spring. Insert the elevator spring arm into its restraint. Extend the spring. Use the paper clip like a handle. Hook the spring onto the spring arm. Part B - Electronics This part of the procedure enables the Stick Mode menu option on the transmitter's system memu. Step 6: Remove the bind button board The bind button is connected to a suspended printed circuit board. The board is on stilts in between the stick assemblies. We need to remove that board to access the board underneath. Undo the screws securing that board. Place the board to the side. Be careful not to damage or stress any of the wires connected to that board. Step 7: Solder in the additional resistor and reset the device The main printed circuit board is in the shape of the letter 'T'. Find the two solder dots labeled R41 on the right-hand side of the T.
6 Page 6 of 8 Solder the additional resistor into that position. Resistors are not polarised, so it doesn't matter which way about it goes. Try not to laugh too much at my amateurish soldering job in the photo. Reconnect the battery. Turn on the transmitter. Use a paper clip to momentarily
7 Page 7 of 8 connect the two solder dots labeled 'RESET' - you'll hear a loud beep from the device. Turn off the transmitter. Remove the battery. Step 8: Replace the bind button board and back cover Put everything back together. Replace the battery. Part C - Setup Step 9: Use the new system menu option Use the new menu option on the system menu to set up your transmitter in the mode you prefer. Sources of information The process described here was based on the ideas presented at: hl=en&sl=de&u=
8 Page 8 of 8 3D68300e87dd e d30790%26postid%3D %26threadview% 3D1%26hilight%3D%26hilightuser% 3D&sa=X&oi=translate&resnum=2&ct=result&prev=/search%3Fq%3Ddx6%2Br41% 26hl%3Den%26client%3Dfirefox-a%26rls%3Dorg.mozilla:en-US:official%26hs%3D8vI About I developed this document as I performed the procedure. I changed a mode 2 transmitter to mode 1. All links were working in July Thank you I've gained a lot from the contributions of other radio control enthusiasts on various radio control internet forums over the years, especially RC Groups and Wattflyer. I owe a big debt to the online radio control community. I hope this document helps someone! -- digital21c, July 2007
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.
More informationPage 1 of 14 This install requires work on your supplemental restraint system and could cause injury or damage to your car. If you are not comfortable performing the steps detailed here then do not attempt
More informationFuel Pump & Sending Unit Repair
If your C4 s fuel gauge reads full regardless of how much fuel you actually have, the sending unit in the tank is most likely at fault. If you have priced a new sending unit, you realize that they run
More informationE46 FUEL FILTER CHANGE Pics from CI
1 of 10 5/3/2010 1:48 PM E46 FUEL FILTER CHANGE Pics from 2001 330CI Bellows Expansion Joints Metal Bellows Expansion Joints in Every Style from Flexicraft www.flexicraft.com/metal_bellows Ask a BMW Mechanic
More information1 of 2 9/4/ :27 AM
Ford Mustang IAC IAB - Solving your idle problems http://www.muscularmustangs.com/iac.php 1 of 2 9/4/2010 10:27 AM Solving idle problems part 1 - Cleaning your IAC Does your idle rise and fall over and
More informationMikuni RS Carburetor Conversion
Mikuni RS Carburetor Conversion After putting your carbies on the bench or the kitchen table if the wife is out, you will see that the linkages may be in different positions depending on which brand of
More informationCHAPTER 2: HEAD, BARREL, SUMP, BIGENDS, ALTERNATOR
CHAPTER 2: HEAD, BARREL, SUMP, BIGENDS, ALTERNATOR Posted on the Wildguzzi forum by Pete Roper: December 10, 2005: Contents: Head, barrel and sump off, bigend bearings, alternator off Pic 2-01: Note that
More informationThere is hence three things you can do - add oil, adjust the temp that the clutch begins to engage, or do both.
As most of you may be aware, I have been doing a lot of research lately on our cooling system in the 80's including the fact that we have a dead spot on the OEM temp gauge which prompted me to not rely
More informationAt Mark's suggestion I thought I'd write this up so future Coupe lovers can have as much fun* as I did with this job.
At Mark's suggestion I thought I'd write this up so future Coupe lovers can have as much fun* as I did with this job. My enormous thanks to forum members, particularly glorfindel, for their advice when
More informationBill Conkling July 2012
Bill Conkling July 2012 Introduction: For any ham, there are moments that are priceless, like snagging that elusive rare DX station on a deserted island that hasn t been activated in 52 years. And certainly,
More informationwhat you need to do is hit the taper housing as hard as you can with your hammers AT THE SAME TIME and at a slight angle, what will happen is you
first things first, get the car on axle stands and the wheels off. Open the bonnet to let more light through to the area in which you'll be working. The following guide shows the passenger side being done
More informationBrake System Rebuilding the brake calipers
Page 1 of 39 Brake System Rebuilding the brake calipers Written by the backyard hack mechanic Sean750 Document history: # 14 Jan 2004 added pictures of rear caliper rebuild kit # 13 Nov 2004 added more
More informationReplace clutch and flywheel * (Volkswagen Sharan 2010-Present)
Replace clutch and flywheel * (Volkswagen Sharan 2010-Present) *Caution! This instructions are created by random users and must be used as a reference only! Please, take all safety precautions, and if
More informationChanging the Power Steering Belt
Changing the Power Steering Belt Brett Dukes (Maverick) from the BigJimny Forum has contributed this article to the Website. Many thanks. Whilst off-roading on Sunday, my alternator Fan Belt snapped -
More informationCHAPTER 2. Current and Voltage
CHAPTER 2 Current and Voltage The primary objective of this laboratory exercise is to familiarize the reader with two common laboratory instruments that will be used throughout the rest of this text. In
More information4 pieces of silicone hose Unless you have AEM then you have 2 2.5, 1 3, and 1 3.5
The parts in your kit: 3 pieces of Mandrel-Bent Aluminized Tubing: 1 Straight 1 45 degree bend with straight section 1 curved section 4 pieces of silicone hose 1 2.5 1 3.5 2 3 Unless you have AEM then
More informationWalthers/Life-Like USRA Steam Locomotive
North Raleigh Model Railroad Club Installing Decoders in N Scale Locomotives Detailed Instructions Walthers/Life-Like USRA 2-8-8-2 Steam Locomotive by David Derway May 17, 2010 Table of Contents Introduction...
More informationHere's the difference (externally) in the and 04+ bumper and headlights: (00-03 on top, 04 on bottom)
OK guys, I've been meaning to post this for awhile.. well here it goes. I did the '04 front end conversion on my '01 about 4-5 months ago, but then the dealer had to buy the car back for legal reasons.
More informationHow I Fitted the Digital Temperature Guage... By T-Cut
How I Fitted the Digital Temperature Guage... By T-Cut Here's one way to install the digital temperature gauge designed by Hans Schaaper. I decided to fit mine into the redundant slot above the CD-80 radio
More informationLakela nd H2 Low Speed Stator Coil Installation
Lakela nd H2 Low Speed Stator Coil Installation Step 1: Place the stator assembly on a padded surface to protect the plastic signal generators, and orient it as shown in figure 1. The low speed coil is
More informationDisco 3 Clock Spring / Rotary Coupler replacement
Disco 3 Clock Spring / Rotary Coupler replacement I recently had to change my Clock spring and thought some folks may find it helpful to see what it entailed. I did lots of reading around but couldn t
More information0500 Low Voltage on the Battery or Dead Cell in the Battery
0500 Low Voltage on the Battery or Dead Cell in the Battery Whenever you press the remote transmitter and you get one short beep from the control box, you press the remote and hear a warning buzzer but
More informationMaking Instructions Version 2.1 for Windows
Making Instructions Version 2.1 for Windows Ohbot Ltd. 2017 About Ohbot has seven motors. Each connects to the Ohbrain circuit board and this connects to a computer using a cable. Ohbot software allows
More informationAIRSTREAM LIFE'S (NEARLY) COMPLETE GUIDE TO AIRSTREAM MAINTENANCE BY RICH LUHR
Read Online and Download Ebook AIRSTREAM LIFE'S (NEARLY) COMPLETE GUIDE TO AIRSTREAM MAINTENANCE BY RICH LUHR DOWNLOAD EBOOK : Click link bellow and free register to download ebook: AIRSTREAM MAINTENANCE
More informationReplace C1U-H47 Carburator on Homelite
Replace C1U-H47 Carburator on Homelite Weed Whacker It's cheaper, quicker, and more reliable to replace your carburetor with a new one, rather than rebuilding it. Written By: Gil ifixit CC BY-NC-SA www.ifixit.com
More informationThere was some debate whether or not there was a write up, with Pictures, for replacing the ignition switch.
Replacing the Ignition Switch - Step by Step with Pictures. http://forums.audiworld.com/showthread.php?p=18927576 (Corey 02ALMSTT) (With updates/corrections by Dave F.) February 1, 2013 (I = Corey, mostly)
More informationTriumph Street Triple VSM Grip Heater Install
Triumph Street Triple VSM Grip Heater Install Introduction: With winter fast approaching and with painful memories of last winter riding with the club it was time to do something about getting some grip
More informationRaxiom Mustang Headlights (94-98) - Installation Instructions
Raxiom Mustang Headlights (94-98) - Installation Instructions The below installation instructions work for the following products: Dark Smoked Mustang Headlights (94-98) Raxiom Chrome Mustang Headlights
More informationDisconnect the negative battery cable!
Understanding Mod-3 on a C90 With Wiring Diagrams By DrJones18LC I do not have a C90 at my disposal (or audio/video equipment for that matter) so I can't make a live step by step how-to on doing Mod-3.
More informationSimple Eurorack Row. Kit Builder's Guide. 4mspedals.com
Simple Eurorack Row Kit Builder's Guide 4mspedals.com ' Simple Eurorack Row This guide is for building a single-row eurorack case with a power supply. When completed, the case is ready to accept eurorack
More informationYep no change - it still pumps out hot air no matter how things were set.
Page 1/5 Frequently Asked Questions Question Heating fails to adjust to the temperature you set Answer If you have Dual Zone Heating / Ventillation / Air Conditioning you might find that either side continues
More informationHow to fit the remote parking heater module
How to fit the remote parking heater module The function of this project is to convert a standard fuel burning heater on the diesel models of the Rover 75 and MG ZT to a remote controlled parking heater.
More informationStand Alone Fog Lights Installation Instructions
Tools Required: 1. Trim Removal tool or protected flat screwdriver 2. #2 Phillips Screwdriver 3. 10mm socket 4. 10mm wrench 5. 8mm or 5/16 socket 6. Adjustable Pliers 7. Electrical Tape WARNING!!! Disconnect
More informationU-Score U-Score AAC Rank AAC Rank Vocabulary Vocabulary
go 1 927 you 2 7600 i 3 4443 more 4 2160 help 5 659 it 6 9386 want 7 586 in 8 19004 that 9 10184 like 10 1810 what 11 2560 make 12 1264 is 13 10257 on 14 6674 out 15 2350 do 16 2102 here 17 655 eat 18
More informationBODY-24, Late Model 944 ( and Newer) Dash Replacement
BODY-24, Late Model 944 (1985.5 and Newer) Dash Replacement Introduction Replacing the dash in a late model 944 is not overly difficult. However, it is very tedious and a lot of patience is required. It's
More informationVEHICLE TOWING SAFETY
When you've got the correct gear, some practice and confidence, towing can be as easy as single-vehicle driving. Yet safety should always be your main concern when you're pulling a trailer. Because no
More informationPrint Page Close Window
Page 1 of 14 Print Page Close Window Battery R/C into a USAT GP-9 Printed from: mylargescale.com Forums Topic URL: http://www.mylargescale.com/forum/topic.asp?topic_id=35848 Printed on: 01 Jan 2006 Topic:
More informationLockpicking Tools: User Guide
Lockpicking Tools: User Guide Tips & Tricks for using Lockpicking Tools Contents Introduction..3 Padlock Shims..5 Comb Picks....7 Jiggler Keys...9 The Lock Gun..11 Bypass Sheets....13 Bump Keys...14 Other
More informationDouble Horse 9116 Technical Manual
Double Horse 9116 Technical Manual Compiled from contributions by owners of the DH9116 RC helicopter and members of RC Groups Discussion Forums via the Double horse 9116 Heli Thread at http://www.rcgroups.com/forums/showthread.php?t=1540154
More informationBMW F10 Premium / Professional Audio system - adding a sub woofer part two
BMW F10 Premium / Professional Audio system - adding a sub woofer part two I accept no liability for any work carried out as a result of this guide. Any damage caused to equipment or your car (or you)
More informationSimple DIY Rev Switch Switch on or off anything at an adjustable engine rpm!
Simple DIY Rev Switch Switch on or off anything at an adjustable engine rpm! By Julian Edgar So what about making it a general-purpose rev switch, able to switch pretty well any electrical loads? That
More informationHow To: Fix That Ugly Hanging E-Brake Cable A CFans Members Mod Project by dirtydawg
How To: Fix That Ugly Hanging E-Brake Cable A CFans Members Mod Project by dirtydawg Skill Level: Easy Disclaimer: Please use caution and seek professional assistance when necessary. ColoradoFans.com,
More informationLincoln Mark VII T5 Swap Version submitted by 5.0 bird
Lincoln Mark VII 1984-1989 T5 Swap Version 20070611 submitted by 5.0 bird I've decided to make an article to assist with the T5 swap for the 84-89 Mark VIIs, since I was just in there because my DOA didn't
More informationConversion of a Turnigy 9X to Hall effect sensors
Conversion of a Turnigy 9X to Hall effect sensors Because English is not my mother language I kindly ask to be gracious. Unfortunately I had several times some problems with the low quality potentiometers
More informationVolkswagen New Beetle Headlight Bulb
Volkswagen New Beetle Headlight Bulb Replacement Replace the headlight bulb in a 2002 and later Volkswagen New Beetle. Written By: Nick Ivanov ifixit CC BY-NC-SA www.ifixit.com Page 1 of 7 INTRODUCTION
More information2007 Crown Victoria Police Interceptor (P71) Blend Door Actuator Replacement (If I did it, you can too.)
2007 Crown Victoria Police Interceptor (P71) Blend Door Actuator Replacement (If I did it, you can too.) I'm not saying this is the only way, or even the right way, but it worked for me. First time I've
More informationProjector39/Umnitza BMW Headlight & Re-Installation for E39s Predator Angel Eyes, and Lamin-X Installation
Projector39/Umnitza BMW Headlight & Re-Installation for E39s Predator Angel Eyes, and Lamin-X Installation Now it is time to remove the headlights! Obviously you have to open the hood to do this. 100_3630.jpg
More informationLeafBox manual, v How to set the LeafBox?
LeafBox manual, v1.0 LeafBox should be installed to accelerator pedal plug of Nissan Leaf. It does not matter generation or year of production, but there are various settings depend on your driving mood,
More informationENG-16, Turbocharger Replacement (Including Tips on K27 Turbocharger Installation)
ENG-16, Turbocharger Replacement (Including Tips on K27 Turbocharger Installation) Introduction Replacing the turbocharger on a 951 is not extremely difficult. However, it is very tedious because there
More informationJDM B16 & OBD0 HONDA DISTRIBUTOR REPAIR
PDF Built By: tonyguns Source: Honda Tech JDM B16 & OBD0 HONDA DISTRIBUTOR REPAIR There are two things you should be checking before you begin. First, check the condition of the wiring harness. Pay close
More informationFord Racing BOSS 302 Engine Oil Cooler (11-14 GT)
Tools needed: 14mm hex socket 7mm socket/wrench 8mm socket/wrench Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT) 10mm socket (for airbox removal) ¾ inch or 19mm wrench Torque wrench Appropriate ratchets
More informationJRSC + BBK Install on SVTF. Neil A. Shah medicnas on focaljet September 2006
JRSC + BBK Install on SVTF Neil A. Shah medicnas on focaljet September 2006 ECU up here. When removing make sure the smaller bundles of wires don t get wrapped around the bottom edge and break - this almost
More informationHow to Replace the Main Axle Gear on the Bachmann Spectrum GScale using the NWSL # upgrade gear.
How to Replace the Main Axle Gear on the Bachmann Spectrum GScale 4-4-0 and 2-6-0 Mogul (2001era), using the NWSL #2223-6 upgrade gear. By Paul M. Newitt (all text and photos Copyright Paul M. Newitt,
More informationBuild Instructions and User Guide
Build Instructions and User Guide Getting Started To build the Rock Drill 4069 you will need: Solder Wire Cutters Soldering Iron Small pliers The kit is suitable for beginners or more experienced builders
More informationInstall a starter Relay to cure the Le Sharo s non starting condition
Install a starter Relay to cure the Le Sharo s non starting condition Inspired by Moljinar from VW Vortex Forum Adapted by Jacques Pagé from Yahoo LESHARO OWNERS Group Most starters use an electromagnetic
More informationLast updated: February 15, 2007
Last updated: February 15, 2007 NOTICE: We sell these with complete wiring packs, and with just the Vegtherm tube itself plus the relay, wiring plug for relay, and circuit breaker. There are two different
More informationFront Bumper Installation Instructions
Front Bumper Installation Instructions 1) Remove the factory bumper, air dam, and frame cover (optional). A) Remove the air dam by pulling on the plastic clips holding it in place with a set of pliers.
More informationHow to Choose a Truck Scale Intercom System
How to Choose a Truck Scale Intercom System IntercomsOnline.com When drivers pull on to a truck scale, there often needs to be some form of communication so they know what's expected of them. There are
More information1100MM P-51 Mustang ELECTRIC POWERED REMOTE CONTROL AIRPLANE ELEVENHOBBY.COM
1100MM P-51 Mustang ELECTRIC POWERED REMOTE CONTROL AIRPLANE ELEVENHOBBY.COM WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to
More informationDoor Panel Removal & Window Stop Adjustment
Door Panel Removal & Window Stop Adjustment By: Jeff Wolford Disclaimer: This is simply an article of how I fixed my car. I m not responsible if you break, scratch, or mess up anything following my example.
More informationBHW Engine Coolant Temperature Replacement
BHW Engine Coolant Temperature Replacement NEVER perform this procedure on a hot engine. Parts: 059 919 501 A dual temperature sensor 032 121 142 retaining spring N 903 168 02 sensor round seal N 905 216
More informationwww.odometergears.com Mercedes-Benz Mechanical Odometer Repair This how to can be used for all mechanical repairs as the only difference will be the removal of the instrument cluster. http://www.dieselgiant.com/repairyourodometer.htm
More informationMidnite Kid Basic Solar Charging Kit
What does my kit come with? 1pc MNKID-B 30-amp MPPT Charge Controller 1pc MNBIGBABY- 4 position breaker box 2 pcs MNEPV30- PV and battery breaker 1 pc GFP63 Ground Fault Protection Breaker 2pcs each Strain
More informationRear Wheel Removal (by BassCliff)
Rear Wheel Removal (by BassCliff) Hello to my GS riding friends! After picking up a nail in my rear tire (while on the freeway at 75mph!) I thought I would take a few pictures to help illustrate the rear
More informationSTEPS FOR REMOVING REAR ASHTRAY & CUP HOLDER, CENTER ARMREST, E- BRAKE CONSOLE, FRONT ASHTRAY, LOWER CENTER CONSOLE AND GLOVE BOX
Please give credit where credit is due! This DIY was completed ENTIRELY by the hardest working VW Vortex moderator on the site!! Gary Thompson, Ph.D. - vortex ID VGRT6, email address vgrt6@yahoo.com. Please
More information64MM F-16 Fighting Falcon V2
64MM F-16 Fighting Falcon V2 SIMPLE Simple assembly RIGID STRONG DURABLE EPO STABLE SMOOTH FLYING PERFORMANCE FMSMODEL.COM Table of Contents Introductions 3 Contents of Kit 4 Assemble the plane 5 Battery
More informationECHO. User Manual. Model: PFBD77
ECHO User Manual Model: PFBD77 Thank you for choosing ProFlight. Please read this user manual before using this drone and keep it safe for future reference. CONTENTS Safety 3 Battery Charging 4 Transmitter
More informationLV2000. revision 1.5. Low Voltage Power Supply Retrofit Kit for Wells-Gardner Color XY Monitor, model 19K6100. Installation Instructions ! WARNING!
LV2000 revision 1.5 Low Voltage Power Supply Retrofit Kit for Wells-Gardner Color XY Monitor, model 19K6100 Installation Instructions! WARNING! To successfully install this kit requires that you have good
More informationCelestron CGE Mount PEC Improvement
Celestron CGE Mount PEC Improvement By Mike Dodd, May 26, 2006 Introduction The Celestron CGE is an excellent mid-range telescope mount. It is solidly-built, has a payload capacity of 65 pounds, and uses
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM 2005 ACCORD All 27511 (DX, LX) 2-AND 4-DOOR Issue Date AUG 2004 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit
More informationAutomatic Roof Hatch Opener
Automatic Roof Hatch Opener Installation Guide REQUIRED TOOLS (These tools are required to complete the installation) Cordless Drill 1/8 1/4 Drill Bits 1/8 Pin Punch #2 Philips Bit Rachet Sharpie Hammer
More informationI hope this guide helps you as much as Boomer Bob helped me. We re just sharing what we know to help out other folks. Best of luck! Phil C.
A brief tutorial on swapping cams for the Victory Cross Roads and Cross Country on the Victory Freedom 106 inch V-Twin Engine with 6 speed over drive transmission Disclaimer: Swapping cams on a Victory
More informationThese instructions show how to build the Remote Controlled Fart machine Sound Kit.
Remote Controlled Fart Machine Assembly Instructions These instructions show how to build the Remote Controlled Fart machine Sound Kit. Tools Required Drill with 7/64, 3/16, and ¼ drill bits. Holt melt
More informationHow To: Fit an enclosed induction kit to the V6
How To: Fit an enclosed induction kit to the V6 As a couple have done this I thought I'd have a go, but do a write up at the same time. Here's a quick summary of the equipment you'll be needing: 1 x Universal
More informationHOW TO REPLACE THE SPOILER ON YOUR GEN 3 PRIUS
HOW TO REPLACE THE SPOILER ON YOUR GEN 3 PRIUS Yup, it happened. The spoiler on your beloved Prius has departed this earth and now is in the great junkyard in the sky. This is how you make it all better
More informationReplacing gauge lamps with LED's
Replacing gauge lamps with LED's To pull the gauges just to replace a small bulb is quite a nuisance and the existing bulbs are not all that bright and easily blow. It is thus worthwhile replacing them
More informationRear End Installation and Bearing Kit - 8.8in (86-12 V8; V6)
Rear End Installation and Bearing Kit - 8.8in (86-12 V8; 11-13 V6) Tools Required: Jack Stands 5 Floor Jack 2 Oil Pans 1 Wheel Blocks 2 Differential Oil 3 qts Friction Modifier 3 bottles Tube of Black
More informationFitting Radio Control to a Mamod Boulton
Fitting Radio Control to a Mamod Boulton How To Fit Radio Control To A Mamod Boulton using FlySky Equipment I assume that you already have a Mamod Boulton and have fitted rechargeable AA batteries instead
More information7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions
7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions Nissan GT-R (R35) Silicone Hose Kit Congratulations on your purchase of the COBB GT-R Silicone Hose Kit for your Nissan GT-R. The following
More informationLegacy 3.6R CVT Cooler Installation
2015-2017 Legacy 3.6R CVT Cooler Installation WARNING!! - Modification and working on your car involves some dangers and risks and may cause injury to you or damage to your vehicle if not done properly
More informationM1A1 Thompson Upgrade
M1A1 Thompson Upgrade If you are mechanically inclined at all. This should be no problem. I'll start off with a list of things you will need. Thompson M1A1 Whisky Cigarettes Tools: Flat screwdriver No.
More informationHeadlamp Adjusters motorised conversion by: Ant (Banjo1981)
Headlamp Adjusters motorised conversion by: Ant (Banjo1981) What you will need: E30 adjuster switch assembly E30 Headlight adjusters E36 Adjuster motors (pref with the plugs still attached) Variable resistor
More informationAdjusting Carbs For Re-Jetting (Procedure written for an Intruder 1500 LC) NEWLY UPDATED: APRIL 2003
SECTION ONE: Get Prepared - Tools Adjusting Carbs For Re-Jetting (Procedure written for an Intruder 1500 LC) NEWLY UPDATED: APRIL 2003 Courtesy of: Half-Crazy Get a manual impact driver (the kind you hit
More informationIntroduction Easy operations Advanced owners Filling the Tank Filler cap Refueling
TABLE OF CONTENTS Introduction...4.3 Easy operations...4.4 Advanced owners...4.7 Filling the Tank...4.9 Filler cap...4.10 Refueling...4.11 Checking and Filling...4.12 Hood release...4.13 Engine compartment...4.15
More informationGeneral Purpose Flasher Circuit
General Purpose Flasher Circuit By David King Background Flashing lights can be found in many locations in our neighbourhoods, from the flashing red light over a stop sign, a yellow warning light located
More informationGENERAL LINK-Module 2.4GHz
GENERAL LINK-Module 2.4GHz Operating Instructions NE480133 The GENERAL LINK SYSTEM GENERAL LINK is a Plug-and-Play module that may be used with your FUTABA radio control system to control models from the
More informationWritten By: Evan Noronha
iphone 6s Plus Battery Replacement Replace the battery in an iphone 6s Plus. Written By: Evan Noronha ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION Use this guide to bring life back to your
More informationGeschreven door: Walter Galan
Replacing the battery in your iphone 6 is something you can do yourself with a few tools. Geschreven door: Walter Galan ifixit CC BY-NC-SA nl.ifixit.com Pagina 1 van 20 INTRODUCTIE Bring life back to your
More informationHasse Mods for the Ampeg J20 Guitar Amp
Hasse Mods for the Ampeg J20 Guitar Amp The following is adapted from a post I put up on The Gear Page, in the Amp Techincal forum. It shows the mods I did to my Ampeg J20. Okay, here s my mods for this
More informationCLASSIC PEDAL KIT. Assembly Instructions WHEN YOU CAN T BUY IT BUILD IT. StewMac Monarch RARE / VINTAGE / HARD TO GET
Sheet #i-2205 Updated 2/8 StewMac Monarch CLASSIC PEDAL KIT Kit case is unpainted IN COLLABORATION WITH EarthQuakerDevices Assembly Instructions The Monarch Overdrive is an all discrete, FET-based dirt
More informationInstalling the Audiovox CCS-100 Cruise Control.
Installing the Audiovox CCS-100 Cruise Control. This article was written by: Lon Lawrence w650kawasaki@leaco.net Cruise Control : Audiovox CCS-100 ($89) Webpage : www.summitracing.com Message: I've installed
More informationAssembly and User Guide
Assembly and User Guide 2 Amp Adjustable Electronic Load 30V and 20 Watts Max Powered by: 9V Battery Pico Load is a convenient constant current load for testing batteries and power supplies. The digital
More informationUpgrade v3 to v3.2. SeeMeCNC Guides. Upgrade v3 to v3.2. Rostock Max v3 Uprgade to v3.2. Written By: SeeMeCNC seemecnc.dozuki.
SeeMeCNC Guides Upgrade v3 to v3.2 Rostock Max v3 Uprgade to v3.2 Written By: SeeMeCNC 2018 seemecnc.dozuki.com/ Page 1 of 34 INTRODUCTION This guide is intended to Upgrade a Rostock Max v3 to a Rostock
More informationInstalling LED lights in a Hypercharger By Keith Edwards Joker s Wild! (Wildjokr)
Installing LED lights in a Hypercharger By Keith Edwards Joker s Wild! (Wildjokr) THINGS YOU WILL NEED: A Hypercharger (duh!) LEDs (The ones I got were from Benny Bryant at Fantasies on Wheels in Sylacauga,
More information* Ql! ^0f. B-17 Flying Fortress. 3 axis stabilization
G3&nw * Ql! ^0f B-17 Flying Fortress 3 axis stabilization (HK)EASYSKY ENTERPRISE LIMITED Website: www.easy-sky.net E-mail: rcmodel@easy-sky.net sales@easy-sky.net Tel: 86-755-27891 659 Fax:86-755-27372071
More informationAmp Camp Amp V1.6 Build Guide
Amp Camp Amp V1.6 Build Guide Amp Camp Amp 1.6 illustrated build guide Written By: 6L6 2018 guides.diyaudio.com/ Page 1 of 41 INTRODUCTION This is the build guide for the Amp Camp Amp v1.6. The differences
More informationFitting the Bell Auto Services (B-A-S) TDV6 EGR Blanking Kit to a 2006 model Discovery 3 TDV6 HSE
Fitting the Bell Auto Services (B-A-S) TDV6 EGR Blanking Kit to a 2006 model Discovery 3 TDV6 HSE Before I describe how I did this, I must first thank other members of the Disco3.co.uk forum (namely J,moore
More informationFlip Extension Install Instructions
Tools Required: Tape Measure, knife, Allen key set, Phillips screwdriver, a 1/2" wrench, and a 1/2" socket 1.0 Preparing TRUCKBOSS Deck. 1.1 Remove the plastic end caps from the rear of the TRUCKBOSS deck.
More informationPLEASE READ THROUGH THE WHOLE WRITE UP BEFORE ACTUALLY USING IT!!!!
JDM power folding mirror switch install into stock USDM harness. By: Greg L., Zeke21 on twinturbo.net PLEASE READ THROUGH THE WHOLE WRITE UP BEFORE ACTUALLY USING IT!!!! This is how I was able to get the
More informationInstallation Manual for LCD Boost Controller device.
Installation Manual for LCD Boost Controller device. Main Black box front view. The lonely white 4pin connector above means this box is equipped with the optional serial expansion card. Main black box
More information