Troubleshooting 3Z8 038 Rev B

Size: px
Start display at page:

Download "Troubleshooting 3Z8 038 Rev B"

Transcription

1 Troubleshooting 3Z8 038 Rev B INSTRUCTIONS WARNING INJECTION HAZARD This form is only a quick reference for troubleshooting Graco sprayers. To reduce the risk of serious injury, including fluid injection, while operating, checking, or repairing the sprayer, follow the warnings and instructions in the appropriate complete instruction manual. General Applies to all Airless Paint Sprayers Problem Cause Solution Poor spray pattern, tails Spray tip is worn or too big. Replace the tip. Not enough pressure Paint is too thick. Thin the paint. Stall pressure is out of calibration. Recalibrate the stall pressure. Low fluid delivery Pressure setting is too low. Increase the pressure setting. Excessive surges at the gun Hose is too long, or the diameter is too large. Tip is plugged. Outlet filter is clogged. Pump parts are worn. For longer hoses, pressure drop is much less with 3/8 in. hose than with 1/4 in. hose. One 50 ft. (15 m) length of 3/8 in. hose can increase spraying pressure by as much as 300 psi (21 bar). Unplug the tip. Flush and clean the outlet filter. Check rod, cylinder, piston valve, and intake valve for wear. Repack the pump; use available kit. Paint runs or sags Tip is worn or too big. Replace the tip. Static sparking from gun Sprayer and/or work are not properly grounded. Hose is damaged or is not a static-free airless hose. Ensure that the sprayer and work are grounded. Replace the hose. Spray gun will not shut off Needle and/or diffuser is worn. Repair the gun; use available kit. Paint is built up between needle and diffuser. Clean the gun. Spray gun will not spray Paint supply is empty. Replenish the paint supply. Displacement pump output low Spray tip is clogged. Filter is clogged (gun or sprayer). Pump inlet screen is plugged. Piston ball check is not seating. Intake ball is not seating. Packings are worn or damaged. Clean the tip. Clean the filter. Clean the screen. Replace the piston ball. Replace the intake ball. Repack the pump; use available kit. General Troubleshooting continued

2 General Applies to all Airless Paint Sprayers (continued) Problem Cause Solution Paint leaks into wet-cup Throat packings are worn or damaged. Repack the pump; use available kit. Throat packing nut is loose. Piston rod is damaged. Tighten the throat packing nut just enough to stop the leakage. Replace the piston rod. Pump is hard to prime Air is trapped in the pump. Open the drain valve. When fluid appears, close it. There is an air leak in the connection between the pump and suction tube or siphon tube. Intake valve or piston valve is leaking or stuck. Packings are worn. Paint is too thick. Inlet screen is plugged Tighten the connection. Clean or replace the valve. Repack the pump; use available kit. Thin the paint. Clean or replace the screen. General Applies to Specified Types of Sprayers Problem Applies To: Cause Solution Sprayer will not start Electric sprayers Sprayer is not plugged in. Plug in the sprayer. Motor does not run, or it stops while spraying Electric sprayers ON/OFF switch is turned off. Turn on the switch. Sprayer was left pressurized. Trigger the gun. EM, GM, Ultra sprayers Pressure setting is too low. Motor is overheated. Circuit breaker is tripped, or power supply fuse is blown. Motor is damaged. Spray tip or filter is plugged. Bourdon tube is damaged from freezing or overpressurization. Increase the pressure. Allow the motor to cool. Reset the circuit breaker, or replace the power supply fuse. Replace the motor. Clean the tip or filter. Replace the control box. EM390, EM490 Extension cord is too long. Use a maximum 50 ft (15 m), 12 ga., grounded extension cord. AC motor labors when starting EM390, EM490 Capacitor has failed. Replace the capacitor. Circuit board has failed. Replace the circuit board. Gasoline engine will not start All gas-powered sprayers Gasoline tank is empty. Spark plug cable is disconnected. Refill the gasoline tank. Reconnect the cable. GM3500, GM5000 Oil level is low. Engine switch is not on. Add oil. Turn on the switch. General Troubleshooting continued

3 General Applies to Specified Types of Sprayers (continued) Problem Applies To: Cause Solution Gasoline engine will not start (continued) GH733 Battery is dead. Recharge or replace the battery. Excessive leakage around hydraulic motor piston rod wiper All hydraulicpowered sprayers Piston rod seal is worn or damaged. Replace the seal. Motor/engine runs, but pump does not work All sprayers Pressure setting is too low. Increase the pressure. Tip or filter is plugged. Clean the tip or filter. EH333, EH433 GH533, GH733 GM3500, GM5000 Outlet filter is plugged. Pump is stuck, because material has dried in it. Hydraulic fluid is low. Hydraulic pump is worn or damaged. Hydraulic motor is worn or damaged. Hydraulic motor is stalled. Pressure control switch is turned off. Clutch field is not energized. Clutch is sticking, worn, or damaged. Flush and clean the filter. Repack the pump; use available kit. Add hydraulic fluid. Replace the pump. Replace the motor. For EH333 and EH433, reset the hydraulic motor as follows: 1. Shut off the engine/electric motor to relieve pressure in the hydraulic motor. 2. Remove the nut from the top of the hydraulic motor. The spool is revealed. 3. Use a screwdriver to push down on the top of the spool about 1/2 in. until it is about 1 in. below flush with the top of the hydraulic motor. 4. Replace the nut on the top of the hydraulic motor. For GH533 and GH733, reset the hydraulic motor as follows: 1. Shut off the engine/electric motor to relieve pressure in the hydraulic motor. 2. Press the reset button on the top of the hydraulic motor. Turn on the switch. Check for loose connections; replace the clutch field. Replace the clutch.

4 Ultra and Ultra Plus+ Electrical Troubleshooting NOTE: Check the GENERAL troubleshooting on the previous pages also. Problem Cause Solution Electrical problems Sprayer circuit breaker has popped up. Press the button to reset the circuit breaker. If the circuit breaker continues to open, see Electrical Short on page 6. Diagnosing circuit board indicator lamps. The normal condition is red lamp on, clear lamp on when board is telling pump to run. Condition A Both lamps on, pump does not operate, and motor is not running Motor brush leads or terminals are loose or damaged. Brushes are worn. Brushes should be at least 1/2 in. long. Leads from bridge to motor are not securely fastened and properly mated. G1 and G2 connections between circuit board and bridge or terminals are damaged or loose. Motor brush lead connections and terminals are loose. Brushes are worn. Brushes should be at least 1/2 in. long. Motor brush springs are broken or misaligned. Rolled portion of spring must rest squarely on top of brush. Motor brushes are binding in brush holders. Motor armature commutator has burn spots, gouges and extreme roughness. Motor armature has shorts. Bridge is not functioning properly. Tighten the terminal screws. Replace the terminals and brushes. Replace loose terminals; crimp to leads. Be sure male terminal blades are straight and firmly connected to their mating parts. Clean the circuit board male terminals. Replace loose or damaged terminals. Securely reconnect the leads. Tighten the terminal screws. Replace the brushes if the leads are damaged. Replace the brushes. NOTE: The brushes do not wear at the same rate on both sides of the motor. Check both brushes. Replace the spring if it is broken. Realign the spring with the brush. Clean the brush holders. Remove the carbon with a small cleaning brush. Align the brush leads with the slots in the brush holder to assure free vertical brush movement. Remove the motor cover and brush inspection plates to check. Remove the motor and have the motor shop resurface the commutator, if possible. Check the motor armature for shorts using an armature tester (growler), or perform the spin test. Replace the motor. Check the bridge by substituting it with a good bridge or by performing the bridge test. Replace the bridge. CAUTION Do not perform this check until the motor armature is determined to be good. A bad motor armature will immediately burn out a good bridge. Ultra and Ultra Plus+ Electrical Troubleshooting continued

5 Ultra and Ultra Plus+ Electrical Troubleshooting (continued) Problem Cause Solution Condition B Both lamps off Condition C Red lamps on, clear lamp off Unplug sprayer Low output Circuit breaker button has popped up. Power supply cord is damaged. ON/OFF switch is not working. Circuit breaker is not working. Motor thermal cutout switch is not working. Microswitch is not working. Microswitch is faulty. Circuit board is not functioning properly. Circuit board is not functioning properly. Bourdon tube flag and detector are not properly positioned. G1 and G2 leads from bridge to circuit board are defective. Circuit board is not functioning properly. Motor brush leads and terminals are loose. Motor brushes are worn. Motor brushes should be at least 1/2 in. long. Pressure control board is not functioning properly. Motor armature has shorts. Press the button to reset the circuit breaker. If the circuit breaker continues to open, see Electrical Short on page 6. Replace the cord. Replace the switch. Replace the circuit breaker. Allow the motor to cool, correct the cause of overheating, and replace the motor. Clean the microswitch terminals. Replace loose or damaged terminals. Securely reconnect the leads. Visually inspect the microswitch button. The adjustment stud should not press the button when the fluid pressure is zero. Press the button with a small screwdriver. An audible click indicates that the microswitch is in its normal position. If the microswitch is faulty, return the sprayer for repair. Check the circuit board by substituting it with a good board. Replace the circuit board. Replace the circuit board. Perform the pressure control adjustment procedure. If that does not correct the problem, replace the pressure control. Clean the circuit board male terminals. Replace loose or defective lead terminals. Securely reconnect the lead terminals to the board. Check the circuit board by substituting it with a new board. Replace the circuit board. Tighten the terminal screws. Replace the brushes if the leads are damaged. Replace the brushes. Check the pressure control board by substituting it with a good pressure control board. Replace, if necessary. Check the motor armature for shorts, using an armature tester (growler), or perform the spin test. Replace the motor.

6 Ultra and Ultra Plus+ Electrical Troubleshooting (continued) Motor Does Not Operate Type of Problem Basic electrical problems What to Check If check is OK, go to next check. 1. Check the pressure control safety circuit. NOTE: This is possible on Ultra Plus+ sprayers only. 2. Check the electrical supply with a volt meter. The meter should read 105 to 125 VAC. 3. Check the extension cord for damage, and check the extension cord continuity with a volt meter. 4. Check the sprayer power supply cord for damage, such as broken insulation or wires. 5. Check the motor brush leads, terminals, and brush length. Brushes should be at least 1/2 in. long. What to Do When check is not OK refer to this column. 1. Turn the pressure control ON/OFF switch to OFF to RESET. If the pressure control safety continues to trip, see Electrical Short on page Reset the building circuit breaker or replace the building fuse. Try another outlet. 3. Replace the extension cord. 4. Replace the power supply cord. 5. Tighten the terminal screws. Replace the brushes. Electrical Short Type of Problem Building circuit breaker opens as soon as sprayer switch is turned on. CAUTION Any short in any part of the motor power circuit will cause the control circuit to inhibit sprayer operation. Correctly diagnose and repair all shorts before checking and replacing control board. Building circuit breaker opens as soon as sprayer is plugged into outlet, and sprayer is NOT turned on. Sprayer quits after 5 to 10 minutes of operation. What to Check If check is OK, go to next check. 1. Check all electrical wiring for damaged insulation and all terminals for loose fit or damage. Also, check the wires between the pressure control and the motor that are encased in the conduit. 2. Check for missing inspection plate gasket, bent terminal forks, or other metal-to-metal contact points that could cause a short. 3. Check the motor armature for shorts. Use an armature tester (growler), or perform the spin test. Inspect windings for burns. 4. Check the pressure control board by substituting it with a good control board. 1. Check the basic electrical problems under Motor Does Not Operate above. 2. Check the ON/OFF switch. Be sure the sprayer is unplugged! Disconnect the wires from the switch. Check the switch with an ohmmeter. The reading should be infinity with the ON/OFF switch OFF, and zero with the switch ON. 3. Check for damaged or pinched wires in the pressure control. 1. Check the basic electrical problems under Motor Does Not Operate above. 2. Check the electrical supply with a volt meter. The meter should read 105 to 125 VAC. 3. Check the tightness of pump packing nut. Overtightening tightens the packings on the rod, restricts pump action, and damages the packings. What to Do When check is not OK refer to this column. 1. Repair or replace any damaged wiring or terminals. Securely reconnect all wires. 2. Correct any faulty conditions. 3. Replace the motor. 4. Replace the pressure control board with a new board. 1. Perform any necessary procedures. 2. Replace the ON/OFF switch. 3. Replace any damaged parts. 1. Perform any necessary procedures. 2. If the voltage is too high, do not operate the sprayer until it is corrected. 3. Loosen the packing nut. Check for leaking around the throat. Replace the pump packings if necessary.

7 Notes

8 Notes GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN COPYRIGHT 1995, GRACO INC. PRINTED IN U.S.A. 3Z8 038 August 1995 TO PLACE AN ORDER, call Toll Free FOR TECHNICAL ASSISTANCE, call Toll Free

Instructions Parts List

Instructions Parts List Instructions Parts List 120 VAC, 15A ULTRAMAX 795 Airless Paint Sprayer 308800F 3000 psi (21 MPa, 210 bar) Maximum Working Pressure Model 232140, Series A Basic sprayer on upright cart without hose or

More information

290 Easy Airless Paint Sprayer

290 Easy Airless Paint Sprayer INSTRUCTIONS-PARTS LIST 308 745 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Rev. D Supercedes Rev. C ELECTRIC, 230 Vac, 50 Hz 290 Easy Airless Paint

More information

390sts Airless Paint Sprayer

390sts Airless Paint Sprayer INSTRUCTIONS PARTS LIST 308 548 This manual contains important warnings and information. READ AND RETAIN FOR REFERENCE Rev. D Supercedes Rev. C ELECTRIC, 120 VAC 390sts Airless Paint Sprayer 2750 psi (195

More information

395st Airless Paint Sprayer

395st Airless Paint Sprayer INSTRUCTIONS-PARTS LIST 308 714 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Rev. A ELECTRIC, 120 VAC 395st Airless Paint Sprayer 3000 psi (210 bar,

More information

495st Airless Paint Sprayer

495st Airless Paint Sprayer INSTRUCTIONS-PARTS LIST 308 750 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Rev. B Supercedes Rev. A ELECTRIC, 230 VAC, 50/60 Hz 495st Airless Paint

More information

ULTIMATE Plus+ 600 Airless Paint Sprayer

ULTIMATE Plus+ 600 Airless Paint Sprayer OWNER S MANUAL 820 204 Rev. K Supercedes Rev. G, H & J This manual contains important warnings and information. READ AND RETAIN FOR REFERENCE ELECTRIC, 120 VAC ULTIMATE Plus+ 600 Airless Paint Sprayer

More information

DURON Airless Paint Sprayers

DURON Airless Paint Sprayers INSTRUCTIONS-PARTS LIST 308715 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Rev. E DURON Airless Paint Sprayers ELECTRIC, 120 VAC 3000 psi (210 bar,

More information

ULTIMATE Mx 695 Airless Paint Sprayer

ULTIMATE Mx 695 Airless Paint Sprayer This manual contains important warnings and information. READ AND RETAIN FOR REFERENCE OWNER S MANUAL 824 135 Rev. B Supercedes Rev. A ELECTRIC, 120 VAC ULTIMATE Mx 695 Airless Paint Sprayer 3000 psi (210

More information

INSTRUCTIONS-PARTS LIST ULTRA PLUS AIRLESS PAINT SPRAYER

INSTRUCTIONS-PARTS LIST ULTRA PLUS AIRLESS PAINT SPRAYER INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. 308 560 Rev. D Supersedes Rev. B and unreleased Rev. C 220/240 VAC, 8 AMP ULTRA

More information

DISPLACEMENT PUMP INSTRUCTIONS-PARTS LIST Rev. K. Model , Series A Model , Series B Model , Series A

DISPLACEMENT PUMP INSTRUCTIONS-PARTS LIST Rev. K. Model , Series A Model , Series B Model , Series A INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. DISPLACEMENT PUMP 308190 Rev. K 3000 psi (210 bar) MAXIMUM WORKING PRESSURE Model

More information

L1900 and 1900 Airless Paint Sprayer

L1900 and 1900 Airless Paint Sprayer Repair Instructions and Parts List 309508 Rev. M L1900 and 1900 Airless Paint Sprayer For portable spray application of architectural paints and coatings 3000 psi (207 bar, 20.7 MPa) Maximum Working Pressure

More information

WARNING This manual should only be used by a qualified Service Technician. FinishPro 390/395 Airless/Air-Assisted Sprayer Repair Electrical Manual

WARNING This manual should only be used by a qualified Service Technician. FinishPro 390/395 Airless/Air-Assisted Sprayer Repair Electrical Manual FinishPro 390/395 Airless/AirAssisted Sprayer Repair Electrical Manual First choice when quality counts. Rev. B 10/11 /07 FinishPro 395 3.00 ti9026a Red Yel Yel Air Hose Connection FinishPro 390 Exhaust

More information

Repair and Parts. Pro 230ES and Pro 270ES Electric Airless Sprayers 3A2817A EN. Pro 230ES Model: Pro 270ES Model:

Repair and Parts. Pro 230ES and Pro 270ES Electric Airless Sprayers 3A2817A EN. Pro 230ES Model: Pro 270ES Model: Repair and Parts Pro 230ES and Pro 270ES Electric Airless Sprayers 3A2817A EN Pro 230ES Model: 262863 Pro 270ES Model: 262864 3000 psi (20.7 MPa, 207 bar) Maximum Working Pressure Important Safety Instructions

More information

INSTRUCTIONS-PARTS LIST ULTRA MAX 695. Table of Contents. Related Manuals. EUROPRO 650 Airless Paint Sprayer

INSTRUCTIONS-PARTS LIST ULTRA MAX 695. Table of Contents. Related Manuals. EUROPRO 650 Airless Paint Sprayer INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. First choice when quality counts. 309067 Rev. D ULTRA MAX 695 EUROPRO 650 Airless

More information

Electric Airless Sprayers

Electric Airless Sprayers Repair Electric Airless Sprayers 312496H EN - For portable spray application of architectural paints and coatings. For professional use only.- Maximum Working Pressure: 3300 psi (227 bar, 22.7 MPa) IMPORTANT

More information

590st Airless Paint Sprayer

590st Airless Paint Sprayer INSTRUCTIONS-PRTS LIST INSTRUCTIONS This manual contains important warnings and information. RED ND KEEP FOR REFERENCE. First choice when quality counts. 308 559 Rev. Supersedes Rev and PCN ELECTRIC, 100

More information

GM 3000 AIRLESS PAINT SPRAYERS Drive Housing Replacement Kit Pinion Housing Replacement Kit

GM 3000 AIRLESS PAINT SPRAYERS Drive Housing Replacement Kit Pinion Housing Replacement Kit INSTRUCTIONS 08660 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Rev. B GM 000 AIRLESS PAINT SPRAYERS Drive Housing Replacement Kit 869 Pinion Housing

More information

695 Standard Premium Standard Premium Standard * Premium *

695 Standard Premium Standard Premium Standard * Premium * Repair Ultimate Mx II 695/795/1095/1595 Airless Sprayers 3300 psi (227 bar, 22.7 MPa) Maximum Working Pressure 309942 Rev. F Vac Model Standard/ Premium 695 Standard 826048 826047 Premium 826041 826040

More information

Electric Airless Sprayer

Electric Airless Sprayer Repair Electric Airless Sprayer 332257A EN - For the application of architectural paints and coatings - - For professional use only - Model 278680 3300 psi (22.7 MPa, 227 bar) Maximum Working Pressure

More information

INSTRUCTIONS-PARTS LIST. ULTRA MAX 695 Airless Paint Sprayer 3000 psi (210 bar, 21 MPa) Maximum Working Pressure. Table of Contents.

INSTRUCTIONS-PARTS LIST. ULTRA MAX 695 Airless Paint Sprayer 3000 psi (210 bar, 21 MPa) Maximum Working Pressure. Table of Contents. INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. First choice when quality counts. 308852 Rev. F ULTRA MAX 695 Airless Paint Sprayer

More information

D Instructions/Parts. Siphon Feed Detail Spray Gun D

D Instructions/Parts. Siphon Feed Detail Spray Gun D Instructions/Parts D-5-55 Siphon Feed Detail Spray Gun FOR PRODUCT INFORMATION CALL: 1-800-742-7731 309991D Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions.

More information

Electric Airless Sprayers Operating Instructions

Electric Airless Sprayers Operating Instructions Electric Airless Sprayers Operating Instructions 309365 Rev. A 3000 psi (210 bar, 21 MPa) Maximum Working Pressure How To Perform: Component Identification....... 3 Setup........................... 4 Startup..........................

More information

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN INSTRUCTIONS-REPAIR INSTRUCTIONS KEEP FOR REFERENCE. Read this and all related manuals for important warnings and instructions. First choice when quality counts. 308922 Rev. B Supercedes Rev. A 495st Airless

More information

MGFHVLP. Instructions/Parts. Mini Gravity Feed System E. Part No Includes MGFHVLP Mini Gravity Feed Spray Gun and MGC 125 Gravity Cup.

MGFHVLP. Instructions/Parts. Mini Gravity Feed System E. Part No Includes MGFHVLP Mini Gravity Feed Spray Gun and MGC 125 Gravity Cup. Instructions/Parts MGFHVLP Mini Gravity Feed System FOR PRODUCT INFORMATION CALL: 1-800-742-7731 309989E For gravity feed spraying of automotive colors and clears. Ideal for touch-up and detail work. Important

More information

309420L. Operation, Repair, and Parts. * The best operating pressure is the lowest pressure that provides an even paint supply to the roller and

309420L. Operation, Repair, and Parts. * The best operating pressure is the lowest pressure that provides an even paint supply to the roller and Operation, Repair, and Parts 309420L For portable spray application of architectural paints and coatings Model 233792, Series B 2800 psi (193 bar, 19 MPa) Maximum Working Pressure* * The best operating

More information

Oregon Fuel Injection

Oregon Fuel Injection Cummins PT Fuel Pump Diagnostic No Start, with no smoke 1. This could be caused by the fuel pump not turning or a seized gear pump. Remove the fuel supply hose and the fuel inlet fitting from the gear

More information

For portable spray application of architectural paints and coatings. For professional use only.

For portable spray application of architectural paints and coatings. For professional use only. Repair and Parts SP200, SP300, AllPro Mustang 2400, Mustang 3100 3A0997F EN For portable spray application of architectural paints and coatings. For professional use only. Important Safety Instructions

More information

Fast-Flo Pump INSTRUCTIONS-PARTS LIST. Table of Contents 1:1 RATIO

Fast-Flo Pump INSTRUCTIONS-PARTS LIST. Table of Contents 1:1 RATIO INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. First choice when quality counts. 07 7 Rev. Z Supersedes W Includes Rev. Y changes

More information

INSTRUCTIONS-PARTS LIST. ULTiMATE Mx 695 Airless Paint Sprayer. Table of Contents. Related Manuals 120 VAC

INSTRUCTIONS-PARTS LIST. ULTiMATE Mx 695 Airless Paint Sprayer. Table of Contents. Related Manuals 120 VAC INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. 309069 Rev. C ULTiMATE Mx 695 Airless Paint Sprayer 3000 psi (207 bar, 20.7 MPa)

More information

Heavy Duty Sprayer Owners Manual Model MS-O

Heavy Duty Sprayer Owners Manual Model MS-O Heavy Duty Sprayer Owners Manual Model MS-O Table of Contents Warranty 4 Warning 5 Assembly and Preparation 6 Operation 7 Cleaning and Storage 7 Standard Spray Gun & Parts List 8 Trigger Style Spray Gun

More information

T-Max 405 Texture Sprayer

T-Max 405 Texture Sprayer Repair T-Max 405 Texture Sprayer 309977H EN For water-based materials only. For professional use only. Not approved for use in European explosive atmosphere locations. Model 248195, Series A Model 248269,

More information

AX Airless Sprayer. Repair B. - For portable spray applications of architectural paints and coatings - (Specifications, page 3)

AX Airless Sprayer. Repair B. - For portable spray applications of architectural paints and coatings - (Specifications, page 3) Repair AX Airless Sprayer 313249B - For portable spray applications of architectural paints and coatings - (Specifications, page 3) Important Safety Instructions Read all warnings and instructions in this

More information

Repair. Clutch Replacement Kit C. GMax and LineLazer Airless Paint Sprayers WARNING. Pressure Relief Procedure

Repair. Clutch Replacement Kit C. GMax and LineLazer Airless Paint Sprayers WARNING. Pressure Relief Procedure Repair Clutch Replacement Kit 309890C EN IMPORTANT SAFETY INSTRUCTIONS Read all warnings and instructions in this manual. Save these instructions. GMax and LineLazer Airless Paint Sprayers Pressure Relief

More information

Troubleshooting the Transmission Hydraulic System

Troubleshooting the Transmission Hydraulic System Testing and Adjusting IT28F INTEGRATED TOOLCARRIER POWER TRAIN Testing And Adjusting Introduction Reference: For Specifications with illustrations, refer to SENR5974, IT28F Integrated Toolcarrier Power

More information

Spray Nozzle Adapters

Spray Nozzle Adapters INSTRUCTIONS-PARTS LIST 306 788 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. First choice when quality counts. Rev. G Supersedes Rev. F DIRECTIONAL

More information

M-3025CB-AV Fuel Pump

M-3025CB-AV Fuel Pump SAVE THESE INSTRUCTIONS M-3025CB-AV Fuel Pump Owner s Manual TABLE OF CONTENTS General Information... 2 Safety Instructions... 2 Installation... 3 Operation... 4 Maintenance... 4 Repair... 5 Troubleshooting...

More information

Electric Diesel Pump EDP/12, EDP/24

Electric Diesel Pump EDP/12, EDP/24 INSTRUCTION MANUAL Electric Diesel Pump EDP/1, EDP/4 S1940, Rev C Congratulations on purchase of this World Class Electric Diesel Pump! Portable Diesel transfer pumps designed for everyday use in Agricultural,

More information

T1-Titanium Non-HVLP Spray Gun

T1-Titanium Non-HVLP Spray Gun T1-Titanium Non-HVLP Spray Gun THE SPRAY GUN PEOPLE FOR PRODUCT INFORMATION CALL: 1-800-742-7731 Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions.

More information

FinishPro II 395/595 Airless/Air-Assisted Sprayer

FinishPro II 395/595 Airless/Air-Assisted Sprayer Repair FinishPro II 395/595 Airless/Air-Assisted Sprayer 333126A EN For the application of architectural paints and coatings. For professional use only. Not approved for use in explosive atmospheres or

More information

190ES/210ES/210ES Plus Electric Airless Sprayer

190ES/210ES/210ES Plus Electric Airless Sprayer Repair 190ES/210ES/210ES Plus Electric Airless Sprayer 312805A - For portable spray application of architectural paints and coatings - 190ES Stand Model: 255847, 255848 210ES Stand Model: 255851 210 Plus

More information

Airless Spray Gun INSTRUCTIONS DP psi (345 bar) Maximum Working Pressure

Airless Spray Gun INSTRUCTIONS DP psi (345 bar) Maximum Working Pressure INSTRUCTIONS DP-6376 Airless Spray Gun 5000 psi (345 bar) Maximum Working Pressure INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Table of Contents Warnings......................................

More information

ILT - Series. Troubleshooting: ILT Twinfold Dual Cylinder Folding Unit

ILT - Series. Troubleshooting: ILT Twinfold Dual Cylinder Folding Unit - Troubleshooting: Twinfold Dual Cylinder Folding Unit Table of content: Page 1) Gate overview...2 2) Gate does not lower down.3 3) Gate is not lifting up....4 4) Electrical schematic 5 5) Hydraulic schematic...6

More information

Viscount I Hydraulic Motor and Displacement Pump

Viscount I Hydraulic Motor and Displacement Pump INSTRUCTIONS-PARTS LIST 308 674 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Rev. C Supersedes Rev. B Viscount I Hydraulic Motor and Displacement Pump

More information

EM 5000 INSTRUCTIONS-PARTS LIST AIRLESS PAINT SPRAYER. Rev. C Supersedes Rev. B and PCN C. ELECTRIC POWERED, 220/240 VAC, 50 Hz, 10 Amp

EM 5000 INSTRUCTIONS-PARTS LIST AIRLESS PAINT SPRAYER. Rev. C Supersedes Rev. B and PCN C. ELECTRIC POWERED, 220/240 VAC, 50 Hz, 10 Amp INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. First choice when quality counts. 307 913 Rev. C Supersedes Rev. B and PCN C ELECTRIC

More information

ULTIMATE Mx 1595 AIRLESS PAINT SPRAYER

ULTIMATE Mx 1595 AIRLESS PAINT SPRAYER This manual contains important warnings and information. READ AND RETAIN FOR REFERENCE OWNER S MANUAL 824165 Rev D 120 VAC ULTIMATE Mx1595 AIRLESS PAINT SPRAYER 3000 psi (210 bar, 21 MPa ) Maximum Working

More information

INSTRUCTIONWFIELD REPAIR

INSTRUCTIONWFIELD REPAIR INSTRUCTIONWFIELD REPAIR 307-670 This manual contains IMPORTANT WARNINGS and INSTRUCTIONS READ AND RETAIN FOR REFERENCE ORAC0 Rev D SUPERSEDES C ULTRA@ 433 AIRLESS PAINT SPRAYER 07 bar 3000 psi) MAXIMUM

More information

HVF110, 210, 310, 410HD

HVF110, 210, 310, 410HD 342 N. Co. Rd. 400 East Valparaiso, IN 46383 219-464-8818 Fax 219-462-7985 www.heatwagon.com Installation and Maintenance Manual Please retain this manual for future reference. HVF110, 210, 310, 410HD

More information

Electric Airless Sprayers

Electric Airless Sprayers Repair Electric Airless Sprayers - For portable spray application of architectural paints and coatings - Maximum Working Pressure: 3300 psi (227 bar, 22.7 MPa) IMPORTANT SAFETY INSTRUCTIONS Read all warnings

More information

Instructions -Repair/Parts

Instructions -Repair/Parts Instructions -Repair/Parts 309879L 2300 and M2300 Airless Sprayer - For portable spray application of architectural paints and coatings - Important Safety Instructions Read all warnings and instructions

More information

Model and Series 115 VAC INDUSTRIAL DIAPHRAGM PUMPS. PumpAgents.com - buy pumps and parts online INDUSTRIAL DIAPHRAGM PUMPS

Model and Series 115 VAC INDUSTRIAL DIAPHRAGM PUMPS. PumpAgents.com - buy pumps and parts online INDUSTRIAL DIAPHRAGM PUMPS Model 31801 and 31800 Series 115 VAC INDUSTRIAL DIAPHRAGM PUMPS INDUSTRIAL DIAPHRAGM PUMPS FEATURES Run Dry Ability Self-Priming Thermal Overload Protected Motor Easy Installation Low Amp Draw Compact

More information

OWNER S MANUAL SELF-PRIMING PORTABLE UTILITY PUMP

OWNER S MANUAL SELF-PRIMING PORTABLE UTILITY PUMP Model 54011-0 OWNER S MANUAL SELF-PRIMING PORTABLE UTILITY PUMP Questions, problems, missing parts? Before returning to the store call AQUAPRO Customer Service 8 a.m. - 5 p.m., EST, Monday-Friday 1-844-242-2475

More information

Maintenance Information

Maintenance Information 45530136 Edition 1 July 2008 Electric Screwdrivers EL 24V DC Series Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing maintenance on this tool.

More information

Maintenance Information

Maintenance Information Form 16575334 Edition 1 April 2005 Electric Screwdrivers EL, EP and ET 34V DC Series Maintenance Information Save These Instructions WARNING Maintenance procedures have the potential for severe shock hazard

More information

k. Components not properly adjusted. Refer to machine technical manual for proper adjustment of components.

k. Components not properly adjusted. Refer to machine technical manual for proper adjustment of components. General Troubleshooting Charts General Troubleshooting Charts Use the charts on the following pages to help in listing all the possible causes of trouble when you begin diagnosing and testing of a machine.

More information

Hydraulic Pumping System

Hydraulic Pumping System Hydraulic Pumping System Easy-Kleen Pressure Systems LTD. 41 Earnhardt Road Sussex Corner, NB E4E 6A1 1 800 315 5533 1 HD SERIES PUMPING SYSTEM WITH HYDRAULIC MOTOR: OPERATION 1. Place unit on level and

More information

LAWN SPRINKLER, IRRIGATION PUMP

LAWN SPRINKLER, IRRIGATION PUMP LAWN SPRINKLER, IRRIGATION PUMP MODEL #, SP0P, SP5P, SP20P, EL0P, EL5P, EL20P SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product.

More information

H3700 Airless Sprayer

H3700 Airless Sprayer Repair H3700 Airless Sprayer 310994E rev.c - For Portable Airless Spraying of Architectural Paints and Coatings- Maximum Working Pressure: 3300 psi (227 bar, 22.7 MPa) IMPORTANT SAFETY INSTRUCTIONS Read

More information

RUFNEX Series Low Profile Wrenches Operation and Maintenance Manual

RUFNEX Series Low Profile Wrenches Operation and Maintenance Manual RUFNEX Series Low Profile Wrenches Operation and Maintenance Manual http://www.torsionx.com Use the RUFNEX Series Ultra-Low Profile Wrenches to install and remove large bolts that have minimal wrench clearance.

More information

6 Litre Oil-Less Air Compressor

6 Litre Oil-Less Air Compressor Operator s Manual 6 Litre Oil-Less Air Compressor WARNING! Before using this appliance, read the Operator s manual and follow all its safety rules and instructions. SPECIFICATION HWKAC1 1.1 kw / 1.5 HP

More information

Portable Oil Free Silent Series Compressor Operating Instructions

Portable Oil Free Silent Series Compressor Operating Instructions Portable Oil Free Silent Series Compressor Operating Instructions NOTICE Carefully read this instruction manual before attempting to operate this compressor. MODEL # SERIAL # 1-800-551-2406 www.eaglecompressor.com

More information

6L Oil-less Air Compressor 53103

6L Oil-less Air Compressor 53103 6L Oil-less Air Compressor 53103 Operating Instructions Please read and save these instructions before attempting to assemble, install, operate or maintain the product. Protect yourself and others by observing

More information

Instructions Parts List

Instructions Parts List Instructions Parts List : RATIO Fast Flo Pump Air operated piston transfer pump for low viscosity fluids. For professional use only. Only models that are EX certified are approved for use in European explosive

More information

Troubleshooting WARNING

Troubleshooting WARNING Troubleshooting WARNING Before troubleshooting or attempting to service, read the following safety rules to avoid accidental exposure to chemical and also risk of electric shock. Note: A reserve, clean

More information

Electric, Heated, Plural Component Proportioner For spraying polyurethane foam and polyurea coatings. Not for use in explosive atmospheres.

Electric, Heated, Plural Component Proportioner For spraying polyurethane foam and polyurea coatings. Not for use in explosive atmospheres. Repair - Parts 309574M Electric, Heated, Plural Component Proportioner For spraying polyurethane foam and polyurea coatings. Not for use in explosive atmospheres. Important Safety Instructions: Read all

More information

3 Phase Smart Controller

3 Phase Smart Controller 3 Phase Smart Controller Installation and Owner s Manual STP-SCIII 208-230 VAC, 60Hz, 120 Volt Coil Franklin Fueling 3760 Marsh Rd. Madison WI 53718 USA Tel: +1 608 838 8786 800 225 9787 Fax: +1 608 838

More information

2015 EDITION SUBMERSIBLE MOTORS AIM MANUAL. APPLICATION INSTALLATION MAINTENANCE 60 Hz, Single-Phase and Three-Phase Motors. franklinwater.

2015 EDITION SUBMERSIBLE MOTORS AIM MANUAL. APPLICATION INSTALLATION MAINTENANCE 60 Hz, Single-Phase and Three-Phase Motors. franklinwater. 0 EDITION AIM MANUAL SUBMERSIBLE MORS APPLICATION INSTALLATION 60 Hz, Single-Phase and Three-Phase Motors franklinwater.com All Motors System Troubleshooting Motor Does Not Start A. No power or incorrect

More information

Hydraulics. Part B, Section 1. This section covers the following unit configurations. 3700V

Hydraulics. Part B, Section 1. This section covers the following unit configurations. 3700V Part B, Section 1 Model Voltage Pump Manifold Control This section covers the following unit configurations. 3500V 3700V 3860 3890 3930 3960 All Piston (D) 4-Port (A) 6-Port (B or C) 2-Port (S or T) Vista

More information

P-200 Plastic Utility Pump for Petroleum Products

P-200 Plastic Utility Pump for Petroleum Products P-200 Plastic Utility Pump for Petroleum Products Owner s Manual 5252 East 36th Street North Wichita, KS USA 67220-3205 TEL: 316-686-7361 FAX: 316-686-6746 A Great Plains Ventures Subsidiary www.gpi.net

More information

FBC CODES AND TRANSLATIONS TRANSLATION

FBC CODES AND TRANSLATIONS TRANSLATION FBC CODES AND TRANSLATIONS CODE TRANSLATION 500 air cleaning system checked 501 air cleaner housing found cracked 502 repaired cracked air cleaner housing 503 renewed air cleaner housing 504 air intake

More information

WEBER CARBURETOR TROUBLESHOOTING GUIDE

WEBER CARBURETOR TROUBLESHOOTING GUIDE This guide is to help pinpoint problems by diagnosing engine symptoms associated with specific vehicle operating conditions. The chart will guide you step by step to help correct these problems. For successful

More information

F PRO. 12 Volt Electric Sprayer. Part #AS76 Copyright 2014 by Hydro-Force Rev. 1/14

F PRO. 12 Volt Electric Sprayer. Part #AS76 Copyright 2014 by Hydro-Force Rev. 1/14 F PRO SPRAYER by 12 Volt Electric Sprayer Part #AS76 Copyright 2014 by Hydro-Force Rev. 1/14 Table of Contents Feature and Benefits... 3 Specifications... 3 Complete Sprayer Diagram... 4 Complete Sprayer

More information

Owner s Manual. LTS Hide-A-Way Truck Side Gate

Owner s Manual. LTS Hide-A-Way Truck Side Gate Owner s Manual LTS Hide-A-Way Truck Side Gate 10900 Kenwood Road Cincinnati, OH 45242 Ph: 513-891-6210 Toll-Free: 866-539-6261 Fax: 513-891-4901 www.leymanlift.com sales@leymanlift.com LML00410-11/6/15

More information

DP556 Pump. 55:1, Air-operated, Grease. General. Operation. Technical Data. Installation. Mounting with Reinforced Cover (Recommended)

DP556 Pump. 55:1, Air-operated, Grease. General. Operation. Technical Data. Installation. Mounting with Reinforced Cover (Recommended) DP556 Pump 55:1, Air-operated, Grease General The DP556 Pump is a compressed air-operated reciprocating piston pump. This high capacity demand pump is compatible with mineral and synthetic grease and suitable

More information

HALLMARK INDUSTRIES INC

HALLMARK INDUSTRIES INC Performance Part No. HP. CONVERTIBLE JET PUMP USER S MANUAL GPH of Water @ Total Discharge Pressure of 40 psi Max. Pressure Max suction (shallow well) Max Suction (deep well) Max GPM (@0 head) Max Discharge

More information

PARTS. Ultra Max 1595 and Mark V Airless Paint Sprayers 3300 psi (227 bar, 22.7 MPa) Maximum Working Pressure. Rev. C

PARTS. Ultra Max 1595 and Mark V Airless Paint Sprayers 3300 psi (227 bar, 22.7 MPa) Maximum Working Pressure. Rev. C PARTS 309268 Rev. C Ultra Max 1595 and Mark V Airless Paint Sprayers 3300 psi (227 bar, 22.7 MPa) Maximum Working Pressure Type Series Model Vac Ultra Max 1595 A 245048 245099 230 100 120 (Japan/Taiwan)

More information

Table 6-1. Problems and solutions with pump operations. No Fluid Delivery

Table 6-1. Problems and solutions with pump operations. No Fluid Delivery Table 6-1. and solutions with pump operations No Fluid Delivery Fluid level in the reservoir is low. Oil intake pipe or inlet filter is plugged. Air leak in the inlet line prevents priming or causes noise

More information

OWNER/OPERATOR MANUAL. Airmotor effective dia. in. 2.5

OWNER/OPERATOR MANUAL. Airmotor effective dia. in. 2.5 MODELS 282050, 282716 & 283513 AIR OPERATED CHASSIS PUMP SERIES A OWNER/OPERATOR MANUAL SPECIFICATIONS Airmotor effective dia. in. 2.5 Airinlet Material outlet 1/4 NPTF 1/4 NPTF Liquid to Air Pressure

More information

DIAGNOSTIC FLOW CHART FOR E-58H & E-61H ELECTRO LIFT UNITS WITH TOUCH PAD

DIAGNOSTIC FLOW CHART FOR E-58H & E-61H ELECTRO LIFT UNITS WITH TOUCH PAD DIAGSTIC FLOW CHART FOR E-58H & E-61H ELECTRO LIFT UNITS WITH TOUCH PAD These charts are intended to be used as an aid in diagnosing problems on the Electro Lift units. They are not a substitute for factory

More information

PRODUCT INFORMATION BULLETIN #3365 DIGITAL MOTOR CONTROL PLATTER SYSTEMS For Serial Number and After

PRODUCT INFORMATION BULLETIN #3365 DIGITAL MOTOR CONTROL PLATTER SYSTEMS For Serial Number and After PRODUCT INFORMATION BULLETIN #3365 DIGITAL MOTOR CONTROL PLATTER SYSTEMS For Serial Number 28640996 and After Record Platter System Identification Numbers Here: Model # Serial # Table of Contents Program

More information

PROBLEM SOLVING GUIDE ELMECO SLUSH MACHINE MODEL FCM

PROBLEM SOLVING GUIDE ELMECO SLUSH MACHINE MODEL FCM A01 INSTRUCTIONS ON HOW TO READ REFERENCES...2 A10 FEATURES AND TECHNICAL SPECIFICATIONS...3 A15 RECOMMENDED PREVENTIVE MAINTENANCE SPARE PARTS KIT...3 A20 IMPORTANT INFORMATION ON FUNCTIONALITY OF THE

More information

Electric Fuel Pump FPM

Electric Fuel Pump FPM INSTRUCTION MANUAL Electric Fuel Pump FPM S1590, Rev B LISTED MOTOR FPM-12, FPM-24, FPM-115, FPM-220 Congratulations on purchase of this World Class Electric Fuel Pump! Elbow This is an Electric Fuel Pump.

More information

Pressure Roller with 24-inch Fixed Extension - For application of architectural paints and coatings -

Pressure Roller with 24-inch Fixed Extension - For application of architectural paints and coatings - Instructions Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. 311082D Pressure Roller with 24-inch Fixed Extension - For application of architectural

More information

180 Lake Ave North Paynesville, MN Phone: (320) MASTER MANUFACTURING MASTER GARDNER

180 Lake Ave North Paynesville, MN Phone: (320) MASTER MANUFACTURING MASTER GARDNER 180 Lake Ave North Paynesville, MN 56362 Phone: (320) 340-6464 www.master-mfg.com MASTER MANUFACTURING MASTER GARDNER Part Number PCD-E3-009B-MM July 2017 Note: Do not return product to the distributor/dealer

More information

Ultra Max II/Ultimate Mx II

Ultra Max II/Ultimate Mx II Repair Ultra Max II/Ultimate Mx II Korean patent10-0579681 311365E - For Portable Airless Spraying of Architectural Coatings and Paints - IMPORTANT SAFETY INSTRUCTIONS. Read all warnings and instructions

More information

DIAGNOSTIC FLOW CHART FOR E-57 & E-60 ELECTRO LIFT UNITS WITH TOUCH PAD

DIAGNOSTIC FLOW CHART FOR E-57 & E-60 ELECTRO LIFT UNITS WITH TOUCH PAD DIAGSTIC FLOW CHART FOR E-57 & E-60 ELECTRO LIFT UNITS WITH TOUCH PAD These charts are intended to be used as an aid in diagnosing problems on the Electro Lift units. They are not a substitute for factory

More information

BRIVIS DUCTED INVERTER SERVICE MANUAL DRCi

BRIVIS DUCTED INVERTER SERVICE MANUAL DRCi BRIVIS DUCTED INVERTER SERVICE MANUAL DRCi 1 TABLE OF CONTENTS TABLE OF CONTENTS... 2 IMPORTANT NOTE... 3 FAULT FINDING AND DIAGNOSTICS... 3 ABBREVIATIONS... 3 PCB S... 4 OUTDOOR MAIN PCB... 4 INDOOR PCB...

More information

EVAPORATIVE EMISSIONS TESTER KLI9210DLX OPERATION MANUAL

EVAPORATIVE EMISSIONS TESTER KLI9210DLX OPERATION MANUAL EVAPORATIVE EMISSIONS TESTER KLI9210DLX OPERATION MANUAL Table of Contents GENERAL INFORMATION...1 UNPACKING & SETUP...2 Inlcuded Accessories...2 CHECK LIST...4 SELF-TEST INSTRUCTIONS...4 CALIBRATING

More information

Owner's Manual. Remote Switch: Outdoor agricultural sprayer kit used to remotely turn On/Off the boom. Read this manual.

Owner's Manual. Remote Switch: Outdoor agricultural sprayer kit used to remotely turn On/Off the boom. Read this manual. M22851A.2 Owner's Manual Remote Switch: Outdoor agricultural sprayer kit used to remotely turn On/Off the boom. WARNING Read this manual. Serious injury or death can result if safety instructions are not

More information

Owner s Manual. SLP Hide-A-Way Tuckunder Style

Owner s Manual. SLP Hide-A-Way Tuckunder Style Owner s Manual SLP Hide-A-Way Tuckunder Style 10900 Kenwood Road Cincinnati, OH 45242 Ph: 513-891-6210 Toll-Free: 866-539-6261 Fax: 513-891-4901 www.leymanlift.com sales@leymanlift.com LML00302-2/05/15

More information

OWNER S MANUAL. Model: LG-30-TRL ( ) (30 Gallon Lawn & Garden Trailer Sprayer)

OWNER S MANUAL. Model: LG-30-TRL ( ) (30 Gallon Lawn & Garden Trailer Sprayer) OWNER S MANUAL Model: LG-30-TRL (5302317) (30 Gallon Lawn & Garden Trailer Sprayer) Technical Specifications 30 Gal. Corrosion-Resistant Polyethylene Tank 12 Volt Diaphragm Pump, 2.1 g.p.m. 60 psi 15 Ft.

More information

Troubleshooting The Transmission Hydraulic System

Troubleshooting The Transmission Hydraulic System 416B, 426B, 428B, 436B, & 438B BACKHOE LOADERS TRANSMISSION Testing And Adjusting Troubleshooting The Transmission Hydraulic System Make reference to the following warning and pressure tap locations for

More information

Repair - Parts M

Repair - Parts M Repair - Parts 312066M Electric, Heated, Plural Component Proportioner. For spraying polyurethane foam and polyurea coatings. For professional use only. Not for use in explosive atmospheres. ENG Important

More information

- For portable spray application of architectural paints and coatings. For professional use only.-

- For portable spray application of architectural paints and coatings. For professional use only.- Repair Electric Airless Sprayers 312361H EN FR ES NL DE - For portable spray application of architectural paints and coatings. For professional use only.- Maximum Working Pressure: 3300 psi (22.7 MPa,

More information

INSTRUCTIONS. US Patent Pending HVLP Turbine Guns

INSTRUCTIONS. US Patent Pending HVLP Turbine Guns INSTRUCTIONS 309317 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Rev. A US Patent Pending HVLP Turbine Guns 10 psi (0.07 MPa,.7 bar) Maximum Inlet

More information

Instructions D. Important Safety Instructions For detailed sprayer information and warnings, see Operation manual. Pressure Relief Procedure

Instructions D. Important Safety Instructions For detailed sprayer information and warnings, see Operation manual. Pressure Relief Procedure Instructions Inlet/Outlet Valve Repair Kit for Project Painter 5, Project Painter 7, X5, X7, LTS 15, LTS 17, Project Painter Plus, M3+, M5+, L10+, Pro Plus 20, Pro Plus 30, and Pro Plus 45 irless Sprayers

More information

VP12 High Viscosity Piston Pump

VP12 High Viscosity Piston Pump 5252 East 36th Street North Wichita, KS USA 67220-3205 TEL: 316-686-7361 FAX: 316-686-6746 VP12 High Viscosity Piston Pump Owner s Manual A Great Plains Ventures Subsidiary www.gpi.net 1-800-835-0113 INSTALLATION

More information

Engine Does Not Start or Is Hard to Start Cause of Trouble. 1. Open the drain screw, and check Fuel not supplied (1) Fuel tank empty

Engine Does Not Start or Is Hard to Start Cause of Trouble. 1. Open the drain screw, and check Fuel not supplied (1) Fuel tank empty 20. Engine Does Not Start or Is Hard to Start 20-1 Engine Output Insufficient 20-2 Poor Performance at Low Speed and Idling 20-3 Poor Performance at High Speed 20-3 Unsatisfactory Operation 20-4 Fuel Gauge

More information

Old. Repair - Parts J

Old. Repair - Parts J Repair - Parts Old 311300J Hydraulic, Heated, Plural Component Proportioner For spraying polyurethane foam and polyurea coatings. Not for use in explosive atmospheres. Important Safety Instructions Read

More information

OWNER S MANUAL SUBMERSIBLE UTILITY PUMP

OWNER S MANUAL SUBMERSIBLE UTILITY PUMP Model 51101-0 OWNER S MANUAL SUBMERSIBLE UTILITY PUMP Questions, problems, missing parts? Before returning to the store call AQUAPRO Customer Service 8 a.m. - 5 p.m., EST, Monday-Friday 1-844-242-2475

More information

Typical Install Instructions

Typical Install Instructions Typical Install Instructions Read & understand all steps of these instructions before beginning this installation. WEBER Conversion Kit, VW T-1/2, up to 1835cc 32 / 36 DFEV Weber Carburetor These instructions

More information