DCMCW60 SERIES FEATURES

Transcription

1 DATASHEET DCMCW SERIES 4:1 Ultra Wide Input Voltage Ranges - C to +95 C Operating Temperature Single Outputs, Standard APPLICATIONS Distributed Power Systems Measurement Equipment Telecom Wireless Networks Industry Control Systems Battery Operated Equipment Military / Defense Applications FEATURES Single Outputs 4:1 Ultra Wide Input Voltage Range: 9-36VDC and 18-75VDC Watts Output Power 1500VDC I/O Isolation Up to 86% High Efficiency Lead Free Design, RoHS Compliant Operating Temperature Range: - C to +95 C (with derating) Remote ON/OFF Standard 2.40 x 2.28 x 0.5 Five-Sided Shielded Metal Case ±10% Output Trim Short Circuit, Over Voltage, Over Load, and Over Temperature Protection Custom Designs Available Optional Heatsink Available (Suffix HS ) DESCRIPTION The DCMCW series of isolated DC/DC power converters provides Watts of continuous output power in a standard 2.40 x 2.28 x 0.5 half-brick package. This series consists of 5V, 12V, and 24VDC single output models with 4:1 input voltage ranges of 9-36VDC or 18~75VDC. Some features include high efficiency up to 86%, remote on/off, adjustable output voltage, 1500VDC I/O isolation, - C~+95 C operating temperature range (with derating), and five-sided shielding. The DCMCW series is RoHS compliant and has short circuit, over load, over voltage, and over temperature protection. These converters are best suited for use in battery operated equipment, measurement equipment, telecom, wireless networks, industry control systems, military/defense applications and anywhere where isolated, tightly regulated voltages and compact size are required. 09/05/ Fax Page 1 of 5

2 TECHNICAL SPECIFICATIONS: DCMCW SERIES All specifications are based on 25 C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. SPECIFICATION TEST CONDITIONS Min Nom Max Unit INPUT SPECIFICATIONS Input Voltage Range 24VDC nominal input models VDC nominal input models VDC Input Surge Voltage 24VDC nominal input models 50 ms max. 48VDC nominal input models VDC Input Reflected Ripple Current Nominal Vin and full load 200 map-p Input Current Input Filter Pi Type Remote ON/OFF Converter ON Open or 3.5V < Vr < 12V Converter: OFF Short (to -Vin) or 0V < Vr < 1.2V Sourcing Current of Remote Control Pin Nominal Vin 0.2 ma Idle Input Current (at Remote OFF State) Nominal Vin 20 ma OUTPUT SPECIFICATIONS Output Voltage Voltage Accuracy Full load and nominal Vin % Output Current Output Trim See page % Minimum Load Capacitive Load Start-up Time Nominal Vin and constant resistive load 150 ms Line Regulation LL to HL at full load % Load Regulation 25% load to full load % Output Power 0 W Ripple & Noise 5VDC & 12VDC models 20MHz Bandwidth 15VDC models 200 mvp-p Temperature Coefficient %/ C Transient Response Overshoot di/dt=0.8a/µs % of Vo Transient Response Settling Time 50% load step change 7.7 ms Remote Sense See Page 4 PROTECTION 5VDC output models 6.2 Over Voltage Protection 12VDC output models Zener Diode Clamp 15 VDC 24VDC output models 27 Short Circuit Protection Hiccup, automatic recovery Over Load Protection % of full load at nominal input 110 % Thermal Shutdown 110 C GENERAL SPECIFICATIONS Efficiency Nominal input Isolation Voltage Input to Output 1500 VDC Isolation Resistance 500VDC 10 GΩ Isolation Capacitance 250 pf Switching Frequency 300 KHz ENVIRONMENTAL SPECIFICATIONS Operating Temperature With derating (see derating curve) C Storage Temperature C Maximum Case Temperature +105 C Relative Humidity 95 % RH Cooling Forced air cooling 1.5m/s MTBF 718,000 hours PHYSICAL SPECIFICATIONS Case Material Aluminum Base Material FR4 PCB Potting Material Silicon rubber (UL94V-0) Soldering Temperature Lead-free wave soldering 2 C/10sec max. Weight 3.42oz (97g) Dimensions (L x W x H) 2.40 x 2.28 x 0.50 inches (61.0 x 57.9 x 12.7 mm) 09/05/ Fax Page 2 of 5

3 MODEL SELECTION TABLE Model Number Input Voltage Output Output Current (1) Input Current Voltage Min Load Full Load No Load Full Load Output Power Efficiency (2) Maximum Capacitive Load DCMCW-24S05 5 VDC 50mA 12000mA 110mA 3205mA W 82% 0µF DCMCW-24S12 24 VDC (9 36 VDC) 12 VDC 50mA 5000mA 110mA 3086mA W 85% 330µF DCMCW-24S24 24 VDC 90mA 2500mA 110mA 3086mA W 85% µf DCMCW-48S05 5 VDC 50mA 12000mA 50mA 1582mA W 83% 0µF DCMCW-48S12 48 VDC (18 75 VDC) 12 VDC 50mA 5000mA 50mA 1524mA W 86% 330µF DCMCW-48S24 24 VDC 90mA 2500mA 50mA 1524mA W 86% µf 1. Output current below this value will not damage these converters; however, they may not meet all listed specifications. 2. Typical value tested at nominal input and full load. 3. For Heatsink option, add the suffix HS to the model number. DERATING CURVES 120 DCMCW-24S5 Power Derating Curve (Without Heatsink) 120 DCMCW-24S5 Power Derating Curve (With Heatsink) Output Power (%) 40 Output Power (%) Ambient Temperature ( C) Ambient Temperature ( C) EFFICIENCY 90 DCMCW-24S5 Input Voltage vs. Efficiency 90 DCMCW-24S5 Output Current vs. Efficiency Efficiency (%) Efficiency (%) Input Voltage (VDC) Output Current (A) 09/05/ Fax Page 3 of 5

4 REMOTE SENSE APPLICATION CIRCUIT The Remote Sense function is used to compensate for the voltage drop incurred when the load is located physically far away from the DC/DC converter providing its power. The remote sense pins are connected as close to the load as possible. The DC/DC converter s regulation specifications are maintained across the points where the remote sense wires are connected at the load. This will remove the effect of the voltage drop caused by the resistance of the wires used to conduct the power from the DC/DC converter to the load. This is represented by R CL1 and R CL2. With the use of remote sense, the effects of R CL1 and R CL2 are eliminated. If the Remote Sense function is not used, the +Sense has to be connected to +Vout and the -Sense has to be connected to -Vout as close to the DC/DC converter as possible. +Vout R CL1 +Vin -Vin +Sense -Sense -Vout Load R and R are line resistors CL1 CL2 R CL2 EXTERNAL OUTPUT TRIM The output is adjustable ±10% of rated output voltage. To trim the output voltage up, place the trim resistor between the Trim and -Vo pins. To trim the output voltage down, place the trim resistor between the Trim and +Vo pins. Trim Up Trim Down DCMCW-XXS05 TRIM TABLE -V o Trim R U Trim +V o R D Trim Trim up R up Trim down R down 10% 5.5V 0.4kΩ 4.5V 0.48kΩ 7.5% 5.375V 5.175kΩ 4.625V 6.08kΩ 5% 5.25V 16.8kΩ 4.75V 17.28kΩ 2.5% 5.125V 49.59kΩ 4.875V 50.89kΩ DCMCW-XXS12 TRIM TABLE DCMCW-XXS24 TRIM TABLE Trim Trim up R up Trim down R down Trim Trim up R up Trim down R down 10% 13.2V 1.06kΩ 10.8V 1.19kΩ 10% 26.4V 5.4kΩ 21.6V 0kΩ 7.5% 12.9V 6.74kΩ 11.1V 23.01kΩ 7.5% 25.8V 13.2kΩ 22.2V 63.9kΩ 5% 12.6V 18.11kΩ 11.4V 66.64kΩ 5% 25.2V 28.8kΩ 22.8V 197kΩ 2.5% 12.3V 52.22kΩ 11.7V 197.5kΩ 2.5% 24.6V 75.6kΩ 23.4V 596kΩ 09/05/ Fax Page 4 of 5

5 MECHANICAL DRAWINGS Standard Heatsink Option (Suffix HS ) Unit: inches (mm) Unit: inches (mm) 2.26 (57.50) 4-M3x0.5 (thru-hole) 2.40 (61.00) 2.00 (50.) (5.08) 0.40 (10.16) 0.50 (12.70) 0.19 (4.) BOTTOM VIEW 1.90 (48.26) (7.62) 0.30 (5.08) (7.62) (5.08) 0.30 (7.62) 0.04 (1.00) (5.10) 0.50 (12.70) 1.85 (46.89) 2.39 (.) 2.00±0.004 (50.±0.10) 1.9±0.004 (48.26±0.10) 0.39 (9.85) 0.58 (14.85) 1. (45.) 0.50 (12.70) (5.10) 2.28 (57.90) 1.74 (44.30) PIN CONNECTIONS Pin Single 1 +Vin 2 -Vin 3 Remote ON/OFF 4 -Sense 5 +Sense 6 +Vout 0.43 (11.00) 0.08 (2.00) 1.85 (46.89) 0.93 (23.70) (5.10) 7 -Vout 2.78 (57.90) PHYSICAL 1. All dimensions are for reference only Weight: 3.42oz (97g) 2. Pin Diameter: 0.04 (1.0) Case Material: Aluminum 3. Tolerance: ±0.02 (±0.5) Base Material: FR4 PCB Potting Material: Silicon rubber (UL94V-0) 8 Trim 1. All dimensions are for reference only 2. Weight: 1.23oz (35g) 3. Material: Aluminum COMPANY INFORMATION Wall Industries, Inc. has created custom and modified units for over 50 years. Our in-house research and development engineers will provide a solution that exceeds your performance requirements on-time and on budget. Our ISO certification is just one example of our commitment to producing a high quality, well-documented product for our customers. Our past projects demonstrate our commitment to you, our customer. Wall Industries, Inc. has a reputation for working closely with its customers to ensure each solution meets or exceeds form, fit and function requirements. We will continue to provide ongoing support for your project above and beyond the design and production phases. Give us a call today to discuss your future projects. Contact Wall Industries for further information: Phone: Toll Free: Fax: Web: Address: (3) (888) (3) sales@wallindustries.com 5 Watson Brook Rd. Exeter, NH /05/ Fax Page 5 of 5