INSTALLATION INSTRUCTIONS

Transcription

1 Flash Shower Valve Rough INSTALLATION INSTRUCTIONS RU0, RU0 RU07, RU08 RU09, RU07E Thank you for selecting American-Standard... the benchmark of fine quality for over 40 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. RECOMMENDED TOOLS Phillips Screwdriver Flat Blade Screwdriver Tubing Cutter Adjustable Wrench Channel Locks Plumbers' Putty or Caulking ROUGHING-IN DIMENSIONS n To assure proper positioning in relation to wall, note roughing-in dimensions. mm (4-7/6") 6 mm (6-/8") FINISHED WALL 7/8" TO " ( TO 50 mm) RU0 OR /" NPT OR /" NPT RU09 CPVC /" NPT RU0 /" STUB OUT /" STUB OUT 4 mm (5-5/8") PLASTER GUARD 89 mm (-/") 0 mm (4") -/4" MAX. (69 mm) -/4" MIN. (45 mm) OPTIONAL TO FINISHED FLOOR USUALLY BETWEEN 65'' AND 78'' RU07 *RU07E 56 mm (6-/8") (ASTM F807-) (ASTM F807-) TOP OF TUB RIM BOTTOM OF TUB 4" (0 mm) /" NPT NOTE: TO AVOID SHOWER RISE OR OTHER RELATED ISSUES, DO NOT USE PEX CONNECTIONS ON ANY OF THE. 56 mm (6-/8") RU08 (ASTM F960) * (ASTM F960) * NOTE: Inlet elbows on RU07E and allows for 80 degree rotation. Product names listed herein are trademarks of AS America, Inc. AS America, Inc

2 STANDARD WALL INSTALLATION CAUTION Turn off hot and cold water supplies before beginning. n See Roughing-in diagram before starting. n Remove the PLASTER GUARD (8) for proper installation. n Mount VALVE BODY to cross brace (" X 4") with-in wall. Use wood screws to secure VALVE BODY to brace. n Connect HOT and COLD water supplies per connection method of selected valve. n Connect RISER PIPE () to VALVE BODY () top outlet marked UP. n Connect TUB FILLER PIPE () to bottom outlet. n Cap off shower pipe (4) and tub filler pipe (5). n With TEST CAP (7) in place and BONNET NUT (6) installed securely, turn on water supplies and check for leaks. n Remove cap 4 to flush the water through shower pipe. n Remove cap 5 to flush the water through tub filler pipe. n Install PLASTER GUARD (8) back onto the valve. Only remove PLASTER GUARD (8) when ready to install trim Kit. n Finished wall should allow for a 4" diameter opening (Use PLASTER GUARD for guidance) NOTE: Cross flow can occur, if hot and cold pressures are not equal during testing. For this situation purchase FLUSH PLUG (M9544) separately. See section for test procedures. CAUTION: After valve installation, inspect the VALVE BODY for any debris. It can damage Pressure Balance Valve cartridge. NOTE: For back to back installation, follow steps mentioned above. Reversal of Hot/Cold water supplies is accomplished by rotating cartridge (supplied with trim) 80 during installation. 4 SIDE VIEW CROSS BRACE -/" (00 mm) 7/8" TO " ( mm to 50 mm) 6 COLD WOOD SCREWS x 4 Cross Brace 4" (0 mm) HOT 7 -/4" MAX. (69 mm) -/4" MIN. (45 mm) 8 NOTE: TO AVOID SHOWER RISE OR OTHER RELATED ISSUES, DO NOT USE PEX CONNECTIONS ON ANY OF THE

3 THIN WALL INSTALL CAUTION Turn off hot and cold water supplies before beginning. n See Roughing-in diagram before starting. n Finished wall should allow for a -/" diameter opening (Use PLASTER GUARD for guidance). n Remove PLASTER GUARD (8), rotate 90 counter clockwise and install the two screws. (Thin wall text should be on top) n Use SELF-CENTERING HOLE GUIDES (9) as a guide for thin wall install. n LOCKING SCREW (0) keeps valve in place when installing. Completely Thread LOCKING SCREW (0) onto PLASTER GUARD (8). n During the installation, make sure to position the Locking feature screw as shown in Figure A below. Once the valve is positioned on the Thin Wall, turn counterclockwise as shown in Figure B to secure VALVE BODY () in place. n Connect HOT and COLD water supplies per connection method of selected valve. n Connect RISER PIPE () to VALVE BODY () top outlet marked UP. n Connect TUB FILLER PIPE () to bottom outlet. n Cap off shower pipe (4) and tub filler pipe (5). n With TEST CAP (7) in place and BONNET NUT (6) installed securely, turn on water supplies and check for leaks. n Remove cap 4 to flush the water through shower pipe. n Remove cap 5 to flush the water through tub filler pipe. NOTE: Cross flow can occur, if hot and cold pressures are not equal. For this situation purchase FLUSH PLUG (M9544) separately. See section for test procedures. CAUTION: After valve installation, inspect the VALVE BODY for any debris. It can damage Pressure Balance Valve cartridge. NOTE: For back to back installation, follow steps mentioned above. Reversal of Hot/Cold water supplies is accomplished by rotating cartridge (supplied with trim) 80 during installation. Fig. A SIDE VIEW Hex Wrench 4 mm COLD -/" 7 Fig. B HOT UNLOCK LOCK - -

4 TEST PROCEDURES FOR FLUSH PLUG (SOLD SEPARATELY) n Unthread BONNET NUT (). n Remove TEST CAP () and install FLUSH PLUG (). n Rotate FLUSH PLUG () so opening for inlet (HOT or COLD) directs water flow to selected outlet (SHOWER or TUB). n Secure FLUSH PLUG () by tightening BONNET NUT (). n Check for leaks and flush lines. n Repeat steps above to Test/Flush alternate flow paths. n Upon completion, unthread BONNET NUT (). Remove FLUSH PLUG (), replace with TEST CAP (), and tighten BONNET NUT ()

5 Flash Shower Valve Rough MODEL NUMBERS RU0 RU07 RU08 RU0, RU0 RU07, RU08 RU09, RU07E RU09 RU07E M A FIXATION RING KIT A /" SWEAT PLUG M A LOCKING CAM SCREW KIT RU0 PURCHASED SEPARATELY M A FIXATION RING KIT M A LOCKING CAM SCREW KIT M A DEEP ROUGH-IN KIT HOT LINE FOR HELP For toll-free information and answers to your questions, call: (800) Weekdays 8:00 a.m. to 6:00 p.m. EST IN CANADA (TORONTO ) Weekdays 8:00 a.m. to 7:00 p.m. EST IN MEXICO Product names listed herein are trademarks of AS America, Inc. AS America, Inc. 08 M A FLUSH PLUG - 5 -