Hydraulic Rotary Hammer Drill

Size: px
Start display at page:

Download "Hydraulic Rotary Hammer Drill"

Transcription

1 M a s c h i n e n f a b r i k G m b H Hydraulic Rotary Hammer Drill Type Techn. Doc. No. 262 Illustration can differ from the original Repair Manual and Spare Parts List _Inst_en_Version_06.doc

2 Repair Disassemble the tool until only if you are skilled and have the appropriate technical knowledge. Problems could be in the hydraulic power supply, the gearbox module, or the power and control (rear) module. Then only disassemble the tool as necessary to repair as required. Keep contaminants such as dirt and grit away from the internal parts at all times. Always determine and correct the cause of the problem prior to re-assemble. Further wear and tool failure can result, if the original cause is not corrected. Prior to disassembly Clean the exterior of the tool. Make sure to have all new seals so they can be replaced during reassembly. Note the orientation of seals before removal. Install new seals in the same position as the original seals. Note: For orientation of the parts refer to the sectional drawing and parts list located at the end of this manual. Re-assembly Before starting reassembly check all parts for wear and replace them if necessary. Wear parts are in particular O-rings, radial shaft seals and bearings. We recommend changing the grease in the gear housing after 300 hours of operation. Use a specialpurpose gear grease only: Consistency class 2 (DIN 51818) Saponification type Lithium Worked penetration 265 to 295 Temperature range -25 C to +125 C The proper quantity of grease is very important from the point of good lubrication and low heat generation. Spare Parts Only original spare parts may be used. There is no warranty for damages and liability is disclaimed, if nonoriginal spare parts and accessories are used _Inst_en_Version_06.doc Page 1 of 14

3 Spare Part List Hydraulic Rotary Hammer Drill Item Qty. Description Part and drawing no. Remarks 1 Output unit, assy see extra list 1 Hydraulic motor see extra list 1 Handle, assy Connection lug Counter sunk screw Socket head screw Socket head screw Gasket * 1 Second handle, assy see extra list 1 Cooling pipe see extra list 1 Hydraulic hose set Carrying case Multi-Oil Spray Type label Round head grooved pin Sign Sticker * Wear parts to be stored in case of continuous use _Inst_en_Version_06.doc Page 2 of 14

4 Spare Part List Hydraulic Rotary Hammer Drill _Inst_en_Version_06.doc Page 3 of 14

5 Spare Parts List Output unit, assy Item Qty. Description Part and Drawing no. Remarks Gearbox housing Tension sleeve Sliding sleeve Bushing Feather key Shifter sleeve, assy Cylinder, assy Impact piston Nut End piece Bevel gears Piston Piston pin, assy Cover Crankshaft Roller Gear pinion Bushing Output shaft Sealing Output unit housing Connecting rod Shaft seal * Slip clutch, assy O-ring * O-ring * O-ring * Pressure spring Feather key Roller O-ring * _Inst_en_Version_06.doc Page 4 of 14

6 Spare Parts List Output unit, assy Item Qty. Description Part and Drawing no. Remarks Scraper Pressure spring Feather key Needle sleeve * Needle sleeve * Socket head screw Grooved ball bearing * Snap ring O-ring * Snap ring Grooved ball bearing * Grooved ball bearing * Grooved ball bearing * Sealing ring * Snap ring Snap ring O-ring * Socket head-screw Sealing U-shape Sealing U-shape * O-ring * Sliding bearing * Shaft sealing ring * Snap ring O-ring * * Wear parts to be stored in case of continuous use! _Inst_en_Version_06.doc Page 5 of 14

7 Spare Parts List Output unit, assy _Inst_en_Version_06.doc Page 6 of 14

8 Spare Part List Hydraulic Motor Item Qty. Description Part and drawing no. Remarks Hydraulic motor with item Shaft sealing ring * Axial disc * Axial thrust bearing * Spacer Carrier Drive shaft O-ring * Cover disc Geroler element Rotary slide Bushing Housing, assy with item Motor cover, assy with item Centring cover, assy, Pinnion shaft Gear rim Pinion Planet carrier, assy Planet wheel Needle cage Grooved ball bearing * Washer Snap ring Snap ring Cylinder pin Socket head screw Gasket * Cylinder pin Driver shaft Socket head screw _Inst_en_Version_06.doc Page 7 of 14

9 Spare Part List Hydraulic Motor Item Qty. Description Part and drawing no. Remarks O-ring * Plug * Threaded pin Socket head screw Governor sleeve Glate Washer Pressure spring Locking washer Valve innert, assy item Snap ring Socket head screw Washer Governor piston valve Spring plate Slide Sleeve * Guide Pressure spring Locking washer O-ring * O-ring * O-ring * Threaded pin O-ring * O-ring * *Wear parts to be stored in case of continuous use _Inst_en_Version_06.doc Page 8 of 14

10 Spare Part List Hydraulic Motor _Inst_en_Version_06.doc Page 9 of 14

11 Spare Parts List Second handle, assy Item Qty. Description Part and Drawing no. Remarks Handle Holder Tensioning belt Hammer screw Knurled screw Depth stop _Inst_en_Version_06.doc Page 10 of 14

12 Spare Parts List Second handle, assy _Inst_en_Version_06.doc Page 11 of 14

13 Spare Parts List Cooling pipe, assy Item Qty. Description Part and Drawing no. Remarks 1 1 Flushing pipe Reducing nipple Ball valve hexagonal Gasket Hose nozzle _Inst_en_Version_06.doc Page 12 of 14

14 Spare Parts List Cooling pipe, assy _Inst_en_Version_06.doc Page 13 of 14

15 Note: _Inst_en_Version_06.doc Page 14 of 14

16 Maschinenfabrik GmbH Fellerstraße 4, Velbert Germany Tel.: Fax: spitznas@spitznas.de Internet: _Inst_en_Version_06.doc

Repair Manual and Spare Parts List

Repair Manual and Spare Parts List Hydraulic Drive Unit Type Techn. Doc. No. 362 and Accessories for Pipe Cutting Machine Darstellung kann vom Original abweichen Repair Manual and 580067000_Inst_en_Version_03 Repair General In general,

More information

Hydraulic Angle Grinder for Underwater Use Type

Hydraulic Angle Grinder for Underwater Use Type M a s c h i n e n f a b r i k G m b H Hydraulic Angle Grinder for Underwater Use Type 1 1585 0010 Illustration can differ from the original Repair Manual and Spare Parts List Compiled: 18.01.13 115850010_Inst_en_Version_03

More information

Repair Manual and Spare Parts List

Repair Manual and Spare Parts List Pneumatic Drive Unit Type Techn. Doc. No. 352 and Accessories for Pipe Cutting Machine Darstellung kann vom Original abweichen Repair Manual and 580027000_Inst_en_Version_02 Repair General In general,

More information

Hydraulic Reciprocating Saw

Hydraulic Reciprocating Saw Hydraulic Reciprocating Saw Type 5 1220 0050 Darstellung kann vom Original abweichen Repair Manual and Spare Parts List Compiled: 29.04.11 www.csunitec.com Page 1 of 16 REPAIR INSTRUCTION Do not disassemble

More information

Pneumatic Angle Grinder also for Underwater Use Type

Pneumatic Angle Grinder also for Underwater Use Type M a s c h i n e n f a b r i k G m b H Pneumatic Angle Grinder also for Underwater Use Type 1 4311 0050 Illustration can differ from the original Repair Manual and Spare Parts List Compiled: 22.06.11 143110050_Inst_en_Version_00

More information

Hydraulic Impact Wrench Type

Hydraulic Impact Wrench Type M a s c h i n e n f a b r i k G m b H Hydraulic Impact Wrench Type 6 1520 0010 Illustration can differ from the original Operation and Maintenance Manual 615200010_en_Version_03 Page 1 of 19 TECHNICAL

More information

Pneumatic Circular Saw. Type Illustration can differ from the original. Spare Parts List

Pneumatic Circular Saw. Type Illustration can differ from the original. Spare Parts List Pneumatic Circular Saw Type Illustration can differ from the original Cleaning Regular cleaning is required for a continuous and proper operation. Clean the housing regularly with a soft cloth, it is important

More information

Pneumatic Corner Drill

Pneumatic Corner Drill Maschinenfabrik GmbH Pneumatic Corner Drill Type 2 1602 0030 Illustration can differ from the original Operation and Maintenance Manual Compiled: 31.07.08 216020030_en.doc Page 1 of 12 TECHNICAL SPECIFICATION

More information

Pneumatic Axial Die Grinder also for Underwater Use Type , 0050

Pneumatic Axial Die Grinder also for Underwater Use Type , 0050 M a s c h i n e n f a b r i k G m b H Pneumatic Axial Die Grinder also for Underwater Use Type 1 5077 0010 0020, 0050 Illustration can differ from the original Repair Manual and Compiled: 18.07.11 150770010_0020_0050_Inst_en_Version_00

More information

SERVICE PARTS LIST 1-1/8" ROTARY HAMMER MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON RD., BROOKFIELD, WI Drwg.

SERVICE PARTS LIST 1-1/8 ROTARY HAMMER MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON RD., BROOKFIELD, WI Drwg. 00 0 200 204 276 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS PAGE 1 OF 3 BULLETIN NO.

More information

Service Handbook High-Pressure Washer Pump

Service Handbook High-Pressure Washer Pump Service Handbook High-Pressure Washer Pump 9.120-014.0 2 A. Water Inlet Filter C. Nozzle Insert 1. Remove filter with a screwdriver. 2. Clean filter with warm water and mild soap. 3. Reinstall filter.

More information

Buy Karcher Parts Online: Need Technical Help? Call: Requests to:

Buy Karcher Parts Online:  Need Technical Help? Call: Requests to: Page 1 of 14 Karcher Model:HD 2700 DH Q/C ( 59588430 ) - Parts Section:1.0 PIECE PARTS 2 91823530 2 CONTROL KNOB 3 91963070 2 SAUCER-HEAD SCREW 5 91834050 2 RUBBER BUFFER 6 91963080 2 BOLT 7 91825060 2

More information

Buy Karcher Parts Online: Need Technical Help? Call: Requests to:

Buy Karcher Parts Online:  Need Technical Help? Call: Requests to: Page 1 of 12 Karcher Model:HD 3000 MTD ( 59588400 ) - Parts Section:1.0 PIECE PARTS 1 91825140 1 BOLT 2 91823530 2 CONTROL KNOB 3 91963010 2 SCREW 5 91834050 2 RUBBER BUFFER 6 91963080 2 BOLT 7 91825060

More information

SPARE PARTS LIST RIDERS P525 D, , 2016

SPARE PARTS LIST RIDERS P525 D, , 2016 SPARE PARTS LIST RIDERS P525 D, 967602101, 2016 CABIN P525 D, 967602101, 2016 CABIN P525 D, 967602101, 2016 Ref Part No Description Remark QTY KIT 1 501 99 86-01 DOOR 1 2 501 99 87-01 SEAL 1 3 579 86 79-01

More information

SPARE PARTS LIST. POWER CUTTERS K960 Chain,

SPARE PARTS LIST. POWER CUTTERS K960 Chain, SPARE PARTS LIST POWER CUTTERS K960 Chain, 2008-03 AIR FILTER K960 Chain, 2008-03 AIR FILTER K960 Chain, 2008-03 Ref Part No Description Remark QTY KIT 1 503 21 53-45 SCREW ITXSCM 2 2 544 87 46-01 LABEL

More information

SPARE PARTS LIST CHAIN SAWS GZ550

SPARE PARTS LIST CHAIN SAWS GZ550 SPARE PARTS LIST CHAIN SAWS ACCESSORIES ACCESSORIES Ref Part No Description Remark QTY KIT 1 501 69 17-01 COMBINATION WRENCH 1 CARBURETOR & AIR FILTER CARBURETOR & AIR FILTER Ref Part No Description Remark

More information

SPARE PARTS LIST. CHAIN SAWS 435 E from

SPARE PARTS LIST. CHAIN SAWS 435 E from SPARE PARTS LIST CHAIN SAWS 435 E from 2011-05- ACCESSORIES 435 E from 2011-05- ACCESSORIES 435 E from 2011-05- Ref Part No Description Remark QTY KIT 1 503 55 85-04 TOOL 1 CARBURETOR 435 E from 2011-05-

More information

SPARE PARTS LIST CHAIN SAWS 365 H,

SPARE PARTS LIST CHAIN SAWS 365 H, SPARE PARTS LIST CHAIN SAWS 365 H, 2013-12 ACCESSORIES 365 H, 2013-12 ACCESSORIES 365 H, 2013-12 Ref Part no. Description Remark Qty Kit 1 503 55 85-03 TOOL KIT 1 2 501 69 17-01 COMBINATION WRENCH 1 1

More information

Buy Karcher Parts Online: Need Technical Help? Call: Requests to:

Buy Karcher Parts Online:  Need Technical Help? Call: Requests to: Page 1 of 11 Karcher Model:HD 2500 MTD ( 59588500 ) - Parts Section:1.0 PIECE PARTS 1 91825140 1 BOLT 2 91823540 2 CONTROL KNOB 3 91963040 2 SAUCER-HEAD SCREW 5 91834050 2 RUBBER BUFFER 6 91963080 2 BOLT

More information

SPARE PARTS LIST. CHAIN SAWS 365 H from

SPARE PARTS LIST. CHAIN SAWS 365 H from SPARE PARTS LIST CHAIN SAWS 365 H from 2017-11- ACCESSORIES 365 H from 2017-11- ACCESSORIES 365 H from 2017-11- Ref Part No Description Remark QTY KIT 1 503 55 85-03 TOOL KIT 1 2 501 69 17-01 COMBINATION

More information

Spare Parts List Hydraulic Cutter

Spare Parts List Hydraulic Cutter Spare Parts List Hydraulic Cutter CombiCutter CC 1501 CC 1501 Part ident. 3363 0028 87 Valid from 02/2003 GB Spare Parts List Hydraulic Cutter CombiCutter CC 1501 Atlas Copco Construction Tools GmbH Atlas

More information

SPARE PARTS LIST. CHAIN SAWS 365SP from

SPARE PARTS LIST. CHAIN SAWS 365SP from SPARE PARTS LIST CHAIN SAWS 365SP from 2018-01- CHAIN BRAKE & CLUTCH COVER 365SP from 2018-01- CHAIN BRAKE & CLUTCH COVER 365SP from 2018-01- Ref Part No Description Remark QTY KIT 1 525 75 52-01 SCREW

More information

REPAIR MANUAL. Version 02/11/01 CD ZF GETRIEBE GMBH SAARBRÜCKEN

REPAIR MANUAL. Version 02/11/01 CD ZF GETRIEBE GMBH SAARBRÜCKEN REPAIR MANUAL 6 HP-26 Version CD ZF GETRIEBE GMBH SAARBRÜCKEN subject to alterations Copyright 2002 all rights reserved and published by ZF Getriebe GmbH, Saarbrücken, Department MKTD No part of this manual

More information

SPARE PARTS LIST CHAIN SAWS GZ381

SPARE PARTS LIST CHAIN SAWS GZ381 SPARE PARTS LIST CHAIN SAWS ACCESSORIES ACCESSORIES Ref Part No Description Remark QTY KIT 1 501 69 17-01 COMBINATION WRENCH 1 CARBURETOR CARBURETOR Ref Part No Description Remark QTY KIT 1 506 45 05-01

More information

1. General Description

1. General Description 1. General Description A: SPECIFICATIONS 1. Type Transmission gear ratio Front reduction gear Rear reduction gear 2. TRANSMISSION GEAR OIL Recommended oil Final Transfer 5-forward speeds with synchromesh

More information

SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 240 R,

SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 240 R, SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 240 R, 2005-09 ACCESSORIES 240 R, 2005-09 ACCESSORIES 240 R, 2005-09 Ref Part No Description Remark QTY KIT 501 19 22-01 TOOL CASING 1 501 60 02-03 SCREWDRIVER

More information

MG Spare parts list. Multi grapple. MG 2700 s/n BGF Construction Tools GmbH No

MG Spare parts list. Multi grapple. MG 2700 s/n BGF Construction Tools GmbH No MG 2700 Spare parts list Multi grapple MG 2700 s/n BGF057417-2017 Construction Tools GmbH No. 3390775501 2017-01-23 General information This spare parts list applies to the following: Part number Description

More information

SPARE PARTS LIST. CHAIN SAWS 455 Rancher

SPARE PARTS LIST. CHAIN SAWS 455 Rancher SPARE PARTS LIST CHAIN SAWS ACCESSORIES ACCESSORIES Ref Part No Description Remark QTY KIT 1 501 69 17-01 COMBINATION WRENCH 1 CARBURETOR & AIR FILTER CARBURETOR & AIR FILTER Ref Part No Description Remark

More information

SPARE PARTS LIST CHAIN SAWS CS2255

SPARE PARTS LIST CHAIN SAWS CS2255 SPARE PARTS LIST CHAIN SAWS ACCESSORIES ACCESSORIES Ref Part No Description Remark QTY KIT 1 501 69 17-01 COMBINATION WRENCH 1 CARBURETOR & AIR FILTER CARBURETOR & AIR FILTER Ref Part No Description Remark

More information

PARTS LIST. Clarke CRD1250 Rotary Hammer Drill. Part Number:

PARTS LIST. Clarke CRD1250 Rotary Hammer Drill. Part Number: PARTS LIST Clarke CRD1250 Rotary Hammer Drill Part Number: - 6482015 Quantity Description Part Number 1 SLIDE CLIP ASSY GRCRD62029 1 CIRCLIP GRCRD62030 1 FRONT CAP ASSY GRCRD62031 1 CON.ROD ASSY GRCRD62070

More information

SPARE PARTS LIST CHAIN SAWS CS2252,

SPARE PARTS LIST CHAIN SAWS CS2252, SPARE PARTS LIST CHAIN SAWS CS2252, 2012-07 ACCESSORIES CS2252, 2012-07 ACCESSORIES CS2252, 2012-07 Ref Part no. Description Remark Qty Kit 1 575 43 92-01 TOOL 1 2 522 52 11-01 COMBINATION WRENCH 1 1 3

More information

Pneumatic Axial Fan Type Tech. Doc. No. 802

Pneumatic Axial Fan Type Tech. Doc. No. 802 Pneumatic Axial Fan Type Tech. Doc. No. 802 Illustration can differ from the original Operation and Maintenance Manual Compiled: 06.08.13 815340300_en_Version_02 Page 1 of 11 ATTENTION!!! This pneumatic

More information

SPARE PARTS LIST. CHAIN SAWS 346 XP, from

SPARE PARTS LIST. CHAIN SAWS 346 XP, from SPARE PARTS LIST CHAIN SAWS 346 XP, from 2015-07 - ACCESSORIES 346 XP, from 2015-07 - ACCESSORIES 346 XP, from 2015-07 - Ref Part No Description Remark QTY KIT 1 503 55 85-01 TOOL 1 2 501 69 17-01 COMBINATION

More information

1. General Description

1. General Description 1. General Description A: SPECIFICATION 1. MANUAL TRANSMISSION AND FRONT DIFFERENTIAL Type Transmission gear ratio Front reduction gear Rear reduction gear Front differential Center differential Final

More information

PARTS LIST FOR NO. 3 SERIES PISTOL AND T HANDLE SCREWDRIVERS

PARTS LIST FOR NO. 3 SERIES PISTOL AND T HANDLE SCREWDRIVERS PARTS LIST FOR NO. 3 SERIES PISTOL AND T HANDLE SCREWDRIVERS NON-REVERSING HANDLE ASSEMBLY (SERIAL NO S. STARTING WITH B & D ) Fig. Part Form A278F Date 10-00/B Page 1 of 6 4. 14309 Ring O 5. 14312 Ring

More information

Printed from MediaCat

Printed from MediaCat Illustration A Crankcase Illustration A Crankcase Ref.Nr. Item code Quantity Description 1 1106 020 2506 1 Crankcase (2) 2-11 2 0000 988 5217 1 Connector (2) 3 0000 988 5200 2 Connector (2) 4 1106 641

More information

SPARE PARTS LIST CHAIN SAWS 465 RANCHER II,

SPARE PARTS LIST CHAIN SAWS 465 RANCHER II, SPARE PARTS LIST CHAIN SAWS CHAIN BRAKE CHAIN BRAKE Ref Part No Description Remark QTY KIT 1 574 60 35-01 CLUTCH COVER ASSY 1 3 735 31 08-20 E-CLIP 1 1 4 503 99 83-01 PAWL 1 1 5 525 38 87-01 CHAIN GUIDE

More information

UOW Series Repair Manual UOW-11 & UOW-T60 Series

UOW Series Repair Manual UOW-11 & UOW-T60 Series UOW Series Repair Manual UOW-11 & UOW-T60 Series 100000 SE Pine St., Portland, OR 97216 800-852-1368 503-254-6600 www.aimco-global.com Contents Page 1. Tools Needed for Repair 2 2. Disassembly and Reassembly

More information

SPARE PARTS LIST TRIMMERS/EDGERS 325 E X-SERIES,

SPARE PARTS LIST TRIMMERS/EDGERS 325 E X-SERIES, SPARE PARTS LIST TRIMMERS/EDGERS 325 E X-SERIES, 2001-01 ACCESSORIES 325 E X-SERIES, 2001-01 ACCESSORIES 325 E X-SERIES, 2001-01 Ref Part No Description Remark QTY KIT 501 60 02-03 SCREWDRIVER 1 502 11

More information

CB Spare parts list. Hydraulic concrete buster. CB 2500 s/n DEQ Construction Tools GmbH No

CB Spare parts list. Hydraulic concrete buster. CB 2500 s/n DEQ Construction Tools GmbH No CB 2500 Spare parts list Hydraulic concrete buster CB 2500 s/n DEQ169050-2018 Construction Tools GmbH No. 3390787501 2018-11-22 General information This spare parts list applies to the following: Part

More information

SPARE PARTS LIST. CHAIN SAWS 440 e II

SPARE PARTS LIST. CHAIN SAWS 440 e II SPARE PARTS LIST CHAIN SAWS ACCESSORIES ACCESSORIES Ref Part No Description Remark QTY KIT 1 503 55 85-04 TOOL 1 CARBURETOR CARBURETOR Ref Part No Description Remark QTY KIT 1 506 45 05-01 CARBURETTOR

More information

SPARE PARTS LIST. CHAIN SAWS 365 X-TORQ from

SPARE PARTS LIST. CHAIN SAWS 365 X-TORQ from SPARE PARTS LIST CHAIN SAWS 365 X-TORQ from 2017-11 - ACCESSORIES 365 X-TORQ from 2017-11 - ACCESSORIES 365 X-TORQ from 2017-11 - Ref Part No Description Remark QTY KIT 1 588 79 74-01 TOOL 1 2 501 69 17-01

More information

SPARE PARTS LIST CHAIN SAWS 455 E

SPARE PARTS LIST CHAIN SAWS 455 E SPARE PARTS LIST CHAIN SAWS ACCESSORIES ACCESSORIES Ref Part No Description Remark QTY KIT 1 501 69 17-01 COMBINATION WRENCH 1 CARBURETOR & AIR FILTER CARBURETOR & AIR FILTER Ref Part No Description Remark

More information

SPARE PARTS LIST CHAIN SAWS 365SP,

SPARE PARTS LIST CHAIN SAWS 365SP, SPARE PARTS LIST CHAIN SAWS 365SP, 2013-12 ACCESSORIES 365SP, 2013-12 ACCESSORIES 365SP, 2013-12 Ref Part no. Description Remark Qty Kit 1 503 55 85-01 TOOL 1 2 501 69 17-01 COMBINATION WRENCH 1 1 3 503

More information

OVERHAUL. 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance.

OVERHAUL. 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance. 4168 OVERHAUL 410F701 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance. 0.10 to 0.40 mm (0.0039 to 0.0157 in.) 0.40 mm (0.0157 in.) C80538 2. INSPECT

More information

ELECTRIC TOOL PARTS LIST

ELECTRIC TOOL PARTS LIST Hitachi Power Tools LIST E493 ELECTRIC TOOL PARTS LIST ROTARY HAMMER Model 2006 7 3 (E1) 1 2 3 4 501 502 48 11 12 13 14 15 24 25 26 30 31 32 25 5 6 16 17 18 19 27 28 33 34 35 7 8 20 29 21 9 22 10 23 36

More information

SPARE PARTS LIST. CHAIN SAWS 450 e II

SPARE PARTS LIST. CHAIN SAWS 450 e II SPARE PARTS LIST CHAIN SAWS CHAIN BRAKE & CLUTCH COVER CHAIN BRAKE & CLUTCH COVER Ref Part No Description Remark QTY KIT 1 544 21 72-01 CLUTCH COVER ASSY 1 2 504 54 28-01 COVER LID 1 1 3 537 04 30-01 BRAKE

More information

K950 RING. model_enhet_yyyy-mm

K950 RING. model_enhet_yyyy-mm A K950 RING 2 3 5 7 1 4 6 8 model_enhet_yyyy-mm Page A K950 Ring Pos. Part No. Description Quantity Notes New Part 1 506 28 09-02 BELT GUARD 1 Incl. 2, 3 2 544 87 25-01 LABEL 1 3 503 20 34-19 SCREW 4 4

More information

TUBULAR HANDLE ASSY CLAMP FILLISTER HEAD SCREW 6X FILLISTER HEAD SCREW 5.5X20

TUBULAR HANDLE ASSY CLAMP FILLISTER HEAD SCREW 6X FILLISTER HEAD SCREW 5.5X20 1 1 038310020 TUBULAR HANDLE ASSY. 2 038310060 CLAMP 3 908006145 FILLISTER HEAD SCREW 6X14 4 913455204 FILLISTER HEAD SCREW 5.5X20 6 957114060 AIR VALVE CPL. 7 038114630 GRIP PLATE 8 038117020 CATCH LEVER

More information

SPARE PARTS LIST. CHAIN SAWS 440 E from

SPARE PARTS LIST. CHAIN SAWS 440 E from SPARE PARTS LIST CHAIN SAWS 440 E from 2011-05 - ACCESSORIES 440 E from 2011-05 - ACCESSORIES 440 E from 2011-05 - Ref Part No Description Remark QTY KIT 1 503 55 85-04 TOOL 1 CARBURETOR 440 E from 2011-05

More information

SPARE PARTS LIST CHAIN SAWS CS2258,

SPARE PARTS LIST CHAIN SAWS CS2258, SPARE PARTS LIST CHAIN SAWS CS2258, 2012-05 ACCESSORIES CS2258, 2012-05 ACCESSORIES CS2258, 2012-05 Ref Part no. Description Remark Qty Kit 1 575 43 92-01 TOOL 1 2 522 52 11-01 COMBINATION WRENCH 1 1 3

More information

SPARE PARTS LIST RIDERS RIDER 111 B, , , , ,

SPARE PARTS LIST RIDERS RIDER 111 B, , , , , SPARE PARTS LIST RIDERS RIDER 111 B, 965996801, 965996885, 966663185, 967186501, 2011-02 CHASSIS & ENCLOSURES RIDER 111 B, 965996801, 965996885, 966663185, 967186501, 2011-02 CHASSIS & ENCLOSURES RIDER

More information

SPARE PARTS LIST. CHAIN SAWS 435 from

SPARE PARTS LIST. CHAIN SAWS 435 from SPARE PARTS LIST CHAIN SAWS 435 from 2011-05 - ACCESSORIES 435 from 2011-05 - ACCESSORIES 435 from 2011-05 - Ref Part no. Description Remark Qty Kit 1 503 55 85-04 TOOL 1 CARBURETOR 435 from 2011-05 -

More information

Hydraulic Motors. Radial Piston Motors Precision drives with fixed displacement RM 80N... - RM 250N... series Vg = 80 ccm/rev ccm/ccm

Hydraulic Motors. Radial Piston Motors Precision drives with fixed displacement RM 80N... - RM 250N... series Vg = 80 ccm/rev ccm/ccm Hydraulic Motors Radial Piston Motors Precision drives with fixed displacement RM 80N... - RM 250N... series Vg = 80 ccm/rev - 250 ccm/ccm Repair Manual Doc.-No. HM3-013 UK Seite 2 Table of contents 1.

More information

Model No. EK8100 POWER CUTTER

Model No. EK8100 POWER CUTTER 1 / 7 2 / 7 3 / 7 4 / 7 5 / 7 6 / 7 7 / 7 1 / 5 Item Parts No. Description I/C Qty N/O Opt. 1 Opt. 2 Note 001 168507-3 TANK CAP COMPLETE 1 D10 INC. 2 002 213080-9 O RING 29.5 1 003 163499-1 SUCTION HEAD

More information

SPARE PARTS LIST. CHAIN SAWS CS2166 from

SPARE PARTS LIST. CHAIN SAWS CS2166 from SPARE PARTS LIST CHAIN SAWS CS2166 from 2013-11 - ACCESSORIES CS2166 from 2013-11 - ACCESSORIES CS2166 from 2013-11 - Ref Part No Description Remark QTY KIT 1 588 79 74-01 TOOL 1 1 2 501 69 17-01 COMBINATION

More information

Illustration Engine. PTX 2710 (EPA 3) Pole pruner. 3/27/2017 Page Copyright COMET USA, INC.

Illustration Engine. PTX 2710 (EPA 3) Pole pruner. 3/27/2017 Page Copyright COMET USA, INC. Documents Engine Starter assy and clutch Tank and air filter Adjustable telescopic pole Pruner Carburetor WT-1150 Accessories 3/27/2017 Page 1-16 Illustration Engine 3/27/2017 Page 2-16 Illustration Engine

More information

1. Spare Parts List 1.1 Preface The spare parts list is only valid for the type and versions of transmission, as shown below. You will find the transm

1. Spare Parts List 1.1 Preface The spare parts list is only valid for the type and versions of transmission, as shown below. You will find the transm S P A R E P A R T S L I S T A N D E X P L O S I O N V I E W P A S C A T A L O G U E R T R E A S P ZF 15 MIV (HBW 150 V) Cod. 310.01.0100 1. Spare Parts List 1.1 Preface The spare parts list is only valid

More information

SPARE PARTS LIST. CHAIN SAWS 365 X-TORQ from

SPARE PARTS LIST. CHAIN SAWS 365 X-TORQ from SPARE PARTS LIST CHAIN SAWS 365 X-TORQ from 2013-11 - ACCESSORIES 365 X-TORQ from 2013-11 - ACCESSORIES 365 X-TORQ from 2013-11 - Ref Part No Description Remark QTY KIT 1 588 79 74-01 TOOL 1 2 501 69 17-01

More information

Spare Parts List Hydraulic Cutter

Spare Parts List Hydraulic Cutter Spare Parts List Hydraulic Cutter CombiCutter CC 4000 CC 4000 002582 Valid from: 07/2002 GB Spare Parts List Hydraulic Cutter CombiCutter CC 4000 Atlas Copco Construction Tools GmbH Atlas Copco Construction

More information

EXPLODED VIEW SERVICE MANUAL PRESSURE WASHER PSI Models Rev. 08/12. (Reversed View) (Reversed View) WARNING

EXPLODED VIEW SERVICE MANUAL PRESSURE WASHER PSI Models Rev. 08/12. (Reversed View) (Reversed View) WARNING SERVICE MANUAL PRESSURE WASHER 26 2 EXPLODED VIEW 14 (Reversed View) 3 18 22 1 17 27 This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive

More information

MODEL DPC7311 POWER CUTTER 14" Tank and Handle Grips Model DPC7310 DPC7311

MODEL DPC7311 POWER CUTTER 14 Tank and Handle Grips Model DPC7310 DPC7311 Tank and Handle Grips 12" 14" POWER CUTTER DPC7310 MODEL 9 11 4 2 3 8 12 14 7 10 25 24 19 22 13 5 30 16 20 29 33 15 1 28 6 18 21 31 26 17 23 27 32 34 37 36 35 209 208 07-05 1 Model DPC7310 Hood, Air filter,

More information

SPARE PARTS LIST TRIMMERS/EDGERS 323 LD,

SPARE PARTS LIST TRIMMERS/EDGERS 323 LD, SPARE PARTS LIST TRIMMERS/EDGERS 323 LD, 2008-03 ACCESSORIES 323 LD, 2008-03 ACCESSORIES 323 LD, 2008-03 Ref Part No Description Remark QTY KIT 1 531 00 92-48 FILTER OIL 1 2 502 28 59-01 STOP 1 3 501 60

More information

HR930 Rotary Rake. Illustrated Parts Breakdown. Tongue & Main Frame. Gearbox & Tine Arm

HR930 Rotary Rake. Illustrated Parts Breakdown. Tongue & Main Frame. Gearbox & Tine Arm HR0 Rotary Rake Illustrated Parts Breakdown Page Page Page Page Page Page Tongue & Main Frame Guards Gearbox & Tine Arm Axle Assembly Rotary Gearbox PTO Shaft 0//0 Tongue & Main Frame 0 0 0 0 Ref# Description

More information

BP 3050, 3050 R. Spare parts list. Bulk pulverizer. BP 3050 s/n DEQ BP 3050 R s/n DEQ

BP 3050, 3050 R. Spare parts list. Bulk pulverizer. BP 3050 s/n DEQ BP 3050 R s/n DEQ BP 3050, 3050 R Spare parts list Bulk pulverizer BP 3050 s/n DEQ169179 - BP 3050 R s/n DEQ169179-2018 Construction Tools GmbH No. 3390758101 2018-01-01 General information This spare parts list applies

More information

BP 2050, 2050 R. Spare parts list. Bulk pulverizer. BP 2050 s/n DEQ BP 2050 R s/n DEQ

BP 2050, 2050 R. Spare parts list. Bulk pulverizer. BP 2050 s/n DEQ BP 2050 R s/n DEQ BP 2050, 2050 R Spare parts list Bulk pulverizer BP 2050 s/n DEQ169181 - BP 2050 R s/n DEQ169181-2018 Construction Tools GmbH No. 3390756701 2018-01-01 General information This spare parts list applies

More information

rev 1_09/20/2017 PS-35C EA3500SR

rev 1_09/20/2017 PS-35C EA3500SR C 1 Tank, Handle 5 7 6 8 17 9 1 2 10 11 12 13 18 19 20 3 21 4 22 23 14 16 2 1 Tank, Handle 1 1 168507-3 TANK CAP COMPLETE 1 1 INC. 2 1 2 213080-9 O RING 29.5 1 1 1 3 163447-0 GASOLINE FILTER 1 1 1 4 195757-7

More information

TCI Trans-Scat

TCI Trans-Scat Page 1 of 5 Return to Instruction Sheet index TCI 400000 Trans-Scat Turbo Hydramatic 400-1965-Up This kit will allow you to re-program your transmission valve body. This kit will give you firm positive

More information

SPARE PARTS LIST CHAIN SAWS

SPARE PARTS LIST CHAIN SAWS SPARE PARTS LIST CHAIN SAWS 61. 2017-08 ACCESSORIES 61. 2017-08 ACCESSORIES 61. 2017-08 Ref Part No Description Remark QTY KIT 1 503 55 85-04 TOOL 1 2 503 62 12-01 GREASE 1 3 501 91 14-01 GREASE GUN 1

More information

SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 223 L,

SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 223 L, SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 223 L, 2006-01 ACCESSORIES 223 L, 2006-01 ACCESSORIES 223 L, 2006-01 Ref Part No Description Remark QTY KIT 1 501 78 33-01 SUSPENSION BAIL 1 2 503 21 83-16 SCREW

More information

SPARE PARTS LIST. CHAIN SAWS CS2166 from

SPARE PARTS LIST. CHAIN SAWS CS2166 from SPARE PARTS LIST CHAIN SAWS CS2166 from 2016-10 - ACCESSORIES CS2166 from 2016-10 - ACCESSORIES CS2166 from 2016-10 - Ref Part No Description Remark QTY KIT 1 588 79 74-01 TOOL 1 1 2 501 69 17-01 COMBINATION

More information

SPARE PARTS LIST. CHAIN SAWS CS2172 from

SPARE PARTS LIST. CHAIN SAWS CS2172 from SPARE PARTS LIST CHAIN SAWS CS2172 from 2013-11 - ACCESSORIES CS2172 from 2013-11 - ACCESSORIES CS2172 from 2013-11 - Ref Part No Description Remark QTY KIT 1 588 79 74-01 TOOL 1 2 501 69 17-01 COMBINATION

More information

SPARE PARTS LIST FRONTRIDERS FR2312 MA, , ,

SPARE PARTS LIST FRONTRIDERS FR2312 MA, , , SPARE PARTS LIST FRONTRIDERS FR2312 MA, 966639801, 966639885, 2011-02 CHASSIS & ENCLOSURES FR2312 MA, 966639801, 966639885, 2011-02 CHASSIS & ENCLOSURES FR2312 MA, 966639801, 966639885, 2011-02 Ref Part

More information

SPARE PARTS LIST. CHAIN SAWS 140 E from

SPARE PARTS LIST. CHAIN SAWS 140 E from SPARE PARTS LIST CHAIN SAWS 140 E from 2012-01 - ACCESSORIES 140 E from 2012-01 - ACCESSORIES 140 E from 2012-01 - Ref Part no. Description Remark Qty Kit 1 503 55 85-04 TOOL 1 CARBURETOR 140 E from 2012-01

More information

ON-THE-VEHICLE BRAKE LATHE

ON-THE-VEHICLE BRAKE LATHE 800 ON-THE-VEHICLE BRAKE LATHE Parts Identification READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit in a binder near the machine for ease

More information

SPARE PARTS LIST. CHAIN SAWS 140 from

SPARE PARTS LIST. CHAIN SAWS 140 from SPARE PARTS LIST CHAIN SAWS 140 from 2012-01 - ACCESSORIES 140 from 2012-01 - ACCESSORIES 140 from 2012-01 - Ref Part no. Description Remark Qty Kit 1 503 55 85-04 TOOL 1 CARBURETOR 140 from 2012-01 -

More information

SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 325 RX,

SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 325 RX, SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 325 RX, 2008-03 ACCESSORIES 325 RX, 2008-03 ACCESSORIES 325 RX, 2008-03 Ref Part No Description Remark QTY KIT 1 531 00 92-48 FILTER OIL 1 2 502 28 59-01 STOP

More information

ALL PRODUCT INDEX RCK60B-22BX

ALL PRODUCT INDEX RCK60B-22BX ALL PRODUCT INDEX RCK60B-22BX UNIVERSAL JOINT GEAR BOX/PULLEY/BLADE MOWER DECK/WHEEL LINKAGE/LIFT ARM ACCESSORIES Ref. RCK60B-22BX Page 65160 Item Part No. Description Book UNIVERSAL JOINT 01A001 UNIVERSAL

More information

Disassembling and assembling transmission

Disassembling and assembling transmission 27-640 Disassembling and assembling transmission Preceding work: Removing and installing transmission with torque converter (27-600). Operation number of operation texts and operation values or standard

More information

DPC6430. Documents DPC Tank and handle grips. 2 Hood, air filter. 3 Muffler, connecting muff. 4 Carburetor. 5 Starter assy., ignition assy.

DPC6430. Documents DPC Tank and handle grips. 2 Hood, air filter. 3 Muffler, connecting muff. 4 Carburetor. 5 Starter assy., ignition assy. Documents 1 Tank and handle grips 2 Hood, air filter 3 Muffler, connecting muff 4 Carburetor 5 Starter assy., ignition assy. 6 Cylinder, crankshaft, clutch 7 Cutting device, protection hood 8 Blades, tools

More information

SPARE PARTS LIST CHAIN SAWS 545

SPARE PARTS LIST CHAIN SAWS 545 SPARE PARTS LIST CHAIN SAWS 545 ACCESSORIES 545 ACCESSORIES 545 Ref Part no. Description Remark Qty Kit 1 575 43 92-01 TOOL 1 2 522 52 11-01 COMBINATION WRENCH 1 1 3 503 55 86-01 SPANNER 1 1 4 503 55 86-02

More information

Installation and Maintenance Instructions JSE MAEAD Extruder Clutch. World Leader in Modular Torque Limiters

Installation and Maintenance Instructions JSE MAEAD Extruder Clutch. World Leader in Modular Torque Limiters World Leader in Modular Torque Limiters Installation and Maintenance Instructions JSE.5-0104MAEAD Extruder Clutch 1304 Twin Oaks Street Wichita Falls, Texas 76302 (940) 723-7800 Fax: (940) 723-7888 E-mail:

More information

Instructions for Parts Books

Instructions for Parts Books Instructions for Parts Books The heading at the top of the page will be the same for the picture of the parts at it is for the page with the part numbers. Definition of column headings on part number pages:

More information

K 970 Ring. Reservdelar Spare parts Ersatzteile Pieces de rechange Piezas de repuesto Ricambi Peças sobresselente

K 970 Ring. Reservdelar Spare parts Ersatzteile Pieces de rechange Piezas de repuesto Ricambi Peças sobresselente IPL, K 970 Ring, 20-2, 576 4 8-0 K 970 Ring Reservdelar Spare parts Ersatzteile Pieces de rechange Piezas de repuesto Ricambi Peças sobresselente 576 4 8-0 HUSQVARNA CONSTRUCTION PRODUCTS No. Pos. Description

More information

MG 400. Spare parts list. Multi grapple. MG 400 s/n BGF Construction Tools GmbH No

MG 400. Spare parts list. Multi grapple. MG 400 s/n BGF Construction Tools GmbH No MG 400 Spare parts list Multi grapple MG 400 s/n BGF074759-2016 Construction Tools GmbH No. 3390774801 2016-07-21 General information This spare parts list applies to the following: Part number Description

More information

Parts Breakdown DCS9010

Parts Breakdown DCS9010 Page 1 of 12 2/8/2008 Page 2 of 12 2/8/2008 Page 3 of 12 2/8/2008 Page 4 of 12 2/8/2008 Page 5 of 12 2/8/2008 Page 6 of 12 2/8/2008 Page 7 of 12 2/8/2008 Page 8 of 12 2/8/2008 Fig # Part ID Part Name Quantity

More information

Spare parts list. Centrifugal pumps CP

Spare parts list. Centrifugal pumps CP Spare parts list Centrifugal pumps CP 000 www.cp.com CP 000 9800 0 0a CP 000 Contents Contents General information............................................................... Spare parts list....................................................................

More information

SPARE PARTS LIST POLE PRUNER/POLE SAWS 327 P4

SPARE PARTS LIST POLE PRUNER/POLE SAWS 327 P4 SPARE PARTS LIST POLE PRUNER/POLE SAWS ACCESSORIES ACCESSORIES Ref Part No Description Remark QTY KIT 1 537 04 07-10 ACCESSORY BAG 1 2 501 69 17-01 COMBINATION WRENCH 1 3 502 21 58-01 WRENCH 1 4 503 97

More information

Remanufactured Transmissions, Spare Parts, and Kits Catalog

Remanufactured Transmissions, Spare Parts, and Kits Catalog S5-42 Spare Parts - Gearbox Housing Group 01.010 1307 201 005 Main Housing 050/051/064/118 1307 201 076 Main Housing 056/057/059/100/102/103/108/109/110/111 1307 201 080 Main Housing 053/054/120 01.012

More information

rev 9_ EK7301 PC-7414 PC-7412

rev 9_ EK7301 PC-7414 PC-7412 1 Fuel Tank, Handle 215 216 217 80 83 217 11 12 58 81 14 30 25 24 19 22 5 16 20 29 33 15 31 79 6 18 214 21 28 17 23 26 27 32 34 38 37 35 209 208 2 1 Fuel Tank, Handle 1 5 394-114-101 SCREW PLUG 4 4 4 1

More information

rev 4_ EK8100 PC-8216

rev 4_ EK8100 PC-8216 1 Fuel Tank, Handle 215 216 217 80 83 217 11 12 58 81 14 30 25 24 19 22 5 16 20 29 33 15 31 79 6 18 214 21 28 17 23 26 27 32 34 38 37 35 209 208 2 1 Fuel Tank, Handle 1 5 394-114-101 SCREW PLUG 4 4 1 5

More information

SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 336 FR

SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 336 FR SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS BEVEL GEAR BEVEL GEAR Ref Part No Description Remark QTY KIT 1 544 21 64-01 GEAR 1 2 537 29 59-02 GEAR HOUSING 1 1 3 738 21 99-00 BALL BEARING 1 1 4 505 13 33-01

More information

SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 135 R

SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS 135 R SPARE PARTS LIST BRUSHCUTTERS/CLEARING SAWS ACCESSORIES ACCESSORIES Ref Part No Description Remark QTY KIT 1 501 19 22-01 TOOL 1 2 531 00 92-48 FILTER OIL 1 3 503 97 65-01 GREASE 1 4 502 28 59-01 STOP

More information

15.Main Shaft Assembly

15.Main Shaft Assembly 15.Main Shaft Assembly A: REMOVAL 1) Remove the manual transmission assembly from vehicle. 2) Remove the transfer case with extension case assembly.

More information

BC Spare parts list. Bucket crusher. BC 2500 s/n DEQ Construction Tools GmbH No

BC Spare parts list. Bucket crusher. BC 2500 s/n DEQ Construction Tools GmbH No BC 2500 Spare parts list Bucket crusher BC 2500 s/n DEQ159235 2018 Construction Tools GmbH No. 3390786201 2018-01-01 General information This spare parts list applies to the following: Part number Description

More information

Pull out clutch E snap ring and withdraw complete clutch pack of clutch E. 6 HP 26 ZF Getriebe GmbH Saarbrücken CD

Pull out clutch E snap ring and withdraw complete clutch pack of clutch E. 6 HP 26 ZF Getriebe GmbH Saarbrücken CD Press down cup spring in the mandrel press with assembly bracket 5x46 002 566 and remove snap ring with suitable pliers. Take out planet carrier and cup spring. Take the O-ring seal off the planet carrier.

More information

SPARE PARTS LIST. POLE PRUNER/POLE SAWS 327 P5x

SPARE PARTS LIST. POLE PRUNER/POLE SAWS 327 P5x SPARE PARTS LIST POLE PRUNER/POLE SAWS ACCESSORIES ACCESSORIES Ref Part No Description Remark QTY KIT 1 537 04 07-10 ACCESSORY BAG 1 2 501 69 17-01 COMBINATION WRENCH 1 3 502 21 58-01 WRENCH 1 4 503 98

More information

Instructions for Parts Books

Instructions for Parts Books Instructions for Parts Books The heading at the top of the page will be the same for the picture of the parts at it is for the page with the part numbers. Definition of column headings on part number pages:

More information

DS 3000 T (EPA 3) Brushcutter. Documents. DS 3000 T (EPA 3) Brushcutter. Engine. Starter assy and clutch. Tank and air filter.

DS 3000 T (EPA 3) Brushcutter. Documents. DS 3000 T (EPA 3) Brushcutter. Engine. Starter assy and clutch. Tank and air filter. Documents Engine Starter assy and clutch Tank and air filter Transmission Carburetor WT-1150 Accessories Illustrated parts list (Head "Load&Go" D.130) 4/26/2016 Page 1-16 Illustration Engine 4/26/2016

More information

396 Series - General Parts

396 Series - General Parts MTU - Product Code 31-48 - 51 396 Series - General Parts Item Description Product_ Code On Hand Qty 0000535858 VALVE STEM SEAL 31 105 0165314283 BAYONET COUPLING 31 2 0165313783 BAYONET COUPLING 31 4 0165310683

More information