INSTALLATION INSTRUCTIONS
|
|
- Marvin Cunningham
- 5 years ago
- Views:
Transcription
1 INSTALLATION INSTRUCTIONS Trans4mer Grille Guard (Black) & (Chrome) Dodge Dakota / Durango 4x4 Trucks Parts List: Part No. Quantity Description Frame Ext, R.H Frame Ext, L.H Brace Side Member, Black Side Member, Chrome Tube, 2-1/2, Black Tube, 2-1/2, Chrome Tube, 1-1/2, Black Tube, 1-1/2, Chrome Washer, Nylon, 1-1/ Washer, Nylon, 2-1/ Shim Plate Torque Spec 3/8 31 lb/ft(42 N-m) 7/16 50 lb/ft(68 N-m) 1/2 75 lb/ft(102 N-m) This WARN Trans4mer system can be customized to give your Dakota or Durango a wide variety of looks, front-end protection and winch mounting capability. The system starts with this strong two-tube Grille Guard that attaches to the truck's frame with brackets designed by Warn engineers to handle up to a 9000 lb Winch. It is durable and good looking, even as a stand alone Grill Guard, but can be easily upgraded with some great options! You can add a third large size tube (Light Bar) that adds even more protection and includes tabs for mounting auxiliary lights. The tubes can be mounted in a variety of positions to achieved the look and function that you desire. You can mount a Winch Carrier Bracket that provides a permanent mount for a Warn winch. You may also add a Receiver Bracket that will handle the Warn Multi-mount winch system, a draw bar or any other accessory that fits the standard 2 inch receiver tube. Finally, Brush Guards that protect the headlights and front corners of the truck can be easily added to any of the options above. WARN Page RevA0
2 1. Remove bumper. Opening vehicle hood will expose bumper bolts to be removed, (2 per side). (Figure 1). The (5) plastic push fasteners located under bumper must also be removed. Be sure to disconnect any wiring or other items that may interfere with bumper removal. Leave factory bumper brackets attached to frame (Figure 2). FIGURE 1 BUMPER BOLTS 2. Remove body mount bolt and rubber from inside the front end of each frame rail. Remove 2 or 3 bumper bracket nuts (depending on vehicle) from inside each frame rail, then install the Frame Extensions and Shim Plates, inside the frame rails onto the factory bolts. (Figure 2) Leave nuts slightly loose. Note: Shim Plates may be needed to obtain a 32 distances between the outside surfaces of the Frame Extensions. Shim Plates are to be placed between Frame Extension and inner wall of frame. Note: If your vehicle had only (2) factory nuts install the supplied 1/2 x 1-1/4 bolt, lockwasher and nut to rear hole of Frame Extension, as shown (Figure 2). Leave fasteners slightly loose. WARN Page RevA0
3 FIGURE 2 FACTORY BUMPER BRACKET L.H. FRAME EXTENSION 1/2 x 1-1/4 BOLT LOCK WASHER NUT FACTORY NUTS REMOVE BODY MOUNT RUBBER INSULATOR SHIM PLATE 3. Cut slots into plastic lower bumper as shown in Figure 3. Note: Use CUTOUT A if you are installing the Diagonal Braces, use CUTOUT B if you are not installing the Diagonal Braces. Note: Use either ILLUSTRATION (1 or2), which ever best resembles your vehicle. FIGURE 3 WARN Page RevA0
4 ILLUSTRATION 1 ILLUSTRATION 2 WARN Page RevA0
5 4. If a Winch Carrier or Receiver Bracket is being installed, the Diagonal Braces must also be installed at this time. Use the supplied 3/8 x 1-1/2 bolt and nylock nut. Tighten fasteners fairly tight, but still allowing Diagonal Braces to be adjusted, Figure 4. FIGURE 4 3/8 x 1-1/2 BOLT NYLOCK NUT FRAME EXTENSION DIAGONAL BRACE 5. Reinstall bumper with Frame Extensions and Diagonal Braces (if installed) protruding through plastic. Tighten bumper bolts securely, Figure 5. Reattach any fasteners or other items previous removed. FIGURE 5 WARN Page RevA0
6 6. Install Side Members onto outer surface of Frame Extensions as shown in Figure 6. Install Winch Carrier and Large Tube with Nylon Washers at top of Side Members also shown in Figure 6. NYLON WASHER LARGE TUBE SMALL TUBE FIGURE 6 SIDE MEMBER 3/8 x 1 BUTTON HEAD BOLT WINCH CARRIER 7/16 x 1-1/4 ROUND HEAD BOLT LOCKWASHER NUT 7. The forward ends of the Diagonal Braces attach to bottom of Winch Carrier at rear winch mounting holes. (Figures 8). FIGURE 8 3/8 x 1-1/2 BOLT LOCKWASHER WARN Page RevA0
7 8. If the Trans4mer is being installed only as a gille guard and a winch is not being mounted at this time, install the tubes in any desired position. If the Winch Carrier or Receiver Kit is being added, install a tube only in the top position and then refer to the specific instructions packaged with those items. Tighten the fasteners securely. 9. Install the winch as described in the Winch Installation Instructions, except use the 3/8 x 1-1/2 bolts thru the braces at the rear winch mounting holes. 10. Hold Side Members in alignment with bumper and tighten all fasteners. Reinstall body mount. 11. Install smaller tube above winch. WARN Page RevA0
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Mounting System Part No. 30090 (black) Part No. 30091 (chrome) for Chev & GMC S-series trucks NOTE: GMC SLE only: This model has a plastic bumper cover which protrudes
More informationPARTS LIST TORQUE SPECIFICATIONS
INSTALLATION INSTRUCTIONS Trans4mer Mounting System Toyota Tacoma Kit No. 32522(black) or 32523(chrome) PARTS LIST PART NO. QUANTITY DESCRIPTION 32503 1 FRAME EXTENSION, R.H. 32504 1 FRAME EXTENSION, L.H.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Mounting System Part No. 38475 (black) Part No. 38476 (chrome) for Chevy S-10 Truck & ZR2 NOTE: Please read these instructions thoroughly before starting installation
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Mounting System Ford F150 Kit No. 76259 (black) or 76260 (stainless steel) As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message has
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount For 2007 Toyota Tundra Kit 76380 (Black) and 76381 (Stainless) Your safety, and the safety of others, is very important. To help you make informed
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD SILVERADO 1500 PART #
INSTALLATION INSTRUCTIONS PART # 3-5863 4-0863 PARTS LIST: Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4 10-1.50mm x 30mm Hex Bolts 1 Driver/Left Mounting
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD GMC SIERRA 1500 EXCLUDES DENALI PART # 4084/
INSTALLATION INSTRUCTIONS GRILLE GUARD 14-15 GMC SIERRA 1500 PART # 4084/ 4084-2 PARTS LIST: GRILLE GUARD Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4
More information(W) INSTALLATION INSTRUCTIONS GRILLE GUARD 2014 GMC SIERRA 1500 EXCLUDES DENALI PART # /
(W) INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 508514/ 508515 PARTS LIST: GRILLE GUARD Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4 10-1.50mm x 30mm
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS For 63600 and 64040 Front Bumper and Winch Mount For Ford Super Duty Trucks As you read these instructions, you may see NOTES, CAUTIONS and WARNINGS. Each message has a specific
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HD BUMPER Kit 66240 (BLACK), 74760 (BLACK) & 74690 TUBELESS (TEXTURED BLK) For 03-Newer Chevy 3/4 Ton Trucks As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS.
More information(2) Top Support Backing Plates. Passenger/Right Top Bracket. (2) Frame Mounting Brackets. (2) 12mm x 35mm Single Bolt Plates
PARTS LIST: 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4 10-1.50mm x 30mm Hex Bolts 1 Driver/Left Mounting Bracket 8 10mm x 27mm OD x 3mm Flat Washers 1 Passenger/Right Mounting Bracket
More informationASSEMBLY & INSTALLATION INSTRUCTIONS
ASSEMBLY & INSTALLATION INSTRUCTIONS VEHICLE MOUNT KIT 99101087 AND VEHICLE CENTER MEMBER For 26 Series: 99100890 TO FIT 2009 & Later FORD F150 4x4 (without EcoBoost V6) 2011 & Later FORD F150 4x4 (with
More informationIMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
IMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE 2009 Toyota RAV-4 Stainless Steel Mesh Grilles L 30 G8P Fine Mesh Part #30-002-09 Quantity Description Part No. Upper Mesh Grille (includes):
More informationINSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063
INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063 PARTS LIST: 1 Grille Guard 2 10-1.5mm Nylon Lock Nuts 1 Driver/Left Frame Mounting Bracket 4 12mm Plastic Washers 1
More informationINSTALLATION INSTRUCTIONS FORD SUPER DUTY NOTE: (Vehicle Retains Tow Hook) PART # P3064
INSTALLATION INSTRUCTIONS 2011-14 FORD SUPER DUTY 250-550 NOTE: (Vehicle Retains Tow Hook) PART # P3064 PARTS LIST: Qty Description Qty Description 1 Grill Guard 2 10mm x mm Hex Bolts 1 Driver/Left Lower
More informationPassenger/Right Top Support Bracket. (2) 10mm Nut Plates
PARTS LIST: 1 Extreme Grille Guard 16 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Frame Mounting Bracket 10 12mm Lock Washers 1 Passenger/Right Frame Mounting Bracket 10 12mm Hex Nuts 1 Driver/Left
More information(2) 10mm Quick Release Bolts with Pivot Washers (4) 10mm Flat Washers (2) 10mm Nylon Lock Nuts. (4) 10mm Plastic Washers
PARTS LIST: EXTREME GRILLE GUARD 1 Extreme Heavy Duty Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left Frame Mounting Bracket 4 10mm x 24mm OD x 2.2mm Flat Washers
More informationINSTALLATION INSTRUCTIONS WARN FRONT RECEIVER For: DODGE RAM, 2500 and 3500, + 03 Kit Number: 65370
INSTALLATION INSTRUCTIONS WARN FRONT RECEIVER For: DODGE RAM, 2500 and 3500, + 03 Kit Number: 65370 USE EXTREME CAUTION WHEN DRILLING ON ANY VEHICLE. MAKE SURE THAT ALL FUEL LINES, BRAKE LINES, ELECTRICAL
More informationLeft and Right Bar Light L Brackets. Driver/Left Frame Bracket
PARTS LIST: 1 Bumper 14 12mm Nylon Lock Nuts 1 Bull Nose Hoop 2 10mm Double Bolt Plates 1 Winch Tray 4 10-1.5mm x 25mm Hex Bolts 1 Driver/left Frame Mounting Bracket 8 10mm x 30mm x 2.5mm Flat Washers
More informationTHE GLIDER 5th Wheel Attachment
April 2007 APPLICATION: INSTALLATION INSTRUCTIONS MODEL NO. 70460 70046 THE GLIDER 5th Wheel Attachment For use on short bed pickup applications US Patent No. 6247720 COMPLETE PARTS LIST Part Description
More informationINSTALLATION INSTRUCTIONS HIDDEN WINCH MOUNTING KIT No for Chevrolet & GMC Trucks (for Warn Winches M6000, M8000, XD9000 & HS9500 only)
INSTALLATION INSTRUCTIONS HIDDEN WINCH MOUNTING KIT No. 61770 for Chevrolet & GMC Trucks (for Warn Winches M6000, M8000, XD9000 & HS9500 only) Warn Light Bar 61090 and many other grille guards can be mounted
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA TOYOTA SEQUOIA PART # P2067
INSTALLATION INSTRUCTIONS GRILLE GUARD 07-14 TOYOTA TUNDRA 08-14 TOYOTA SEQUOIA PART # P2067 PARTS LIST: GRILLE GUARD 1 Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA TOYOTA SEQUOIA PART # 2067/2067-2
INSTALLATION INSTRUCTIONS 07-15 TOYOTA TUNDRA 08-15 TOYOTA SEQUOIA PART # 2067/2067-2 PARTS LIST: 1 Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left Frame Mounting
More informationHiniker Company th St. P.O. BOX 3407 Mankato, MN VEHICLE INSTALLATION INSTRUCTIONS FORD 4x4: SUPER DUTY F
Page of VEHICLE INSTALLATION INSTRUCTIONS FORD x: 00-007 SUPER DUTY F0 30 0 0 INSTRUCTION SHEET NO: 037 Rev. A IMPORTANT: Read The Snowplow Operators Manual Before Assembling This Kit. MFR. Snowplow Prep
More informationINSTALLATION INSTRUCTIONS ARMOUR FRONT BUMPER W/O LED LIGHTS FOR CHEVY COLORADO PART # AFB-CO15
INSTALLATION INSTRUCTIONS ARMOUR FRONT BUMPER W/O LED LIGHTS FOR CHEVY COLORADO 15-17 PART # AFB-CO15 ARMOUR FRONT BUMPER PARTS LIST: 1 ARMOUR Bumper Assembly 2 8mm x 25mm Hex Bolts 1 Driver/left Frame
More informationDODGE DAKOTA RT3 UNDERCARRIAGE MOUNTING INSTRUCTIONS (PART NO. LTA04902)
BOSS PRODUCTS A Division of Northern Star Industries, Inc. P.O. Box 787 Iron Mountain MI 49801-0787 www.bossplow.com 2000 2004 DODGE DAKOTA RT3 UNDERCARRIAGE MOUNTING INSTRUCTIONS (PART NO. LTA04902) PUSHING
More informationINSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063
INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063 PARTS LIST: 1 Grille Guard 2 10-1.5mm Nylon Lock Nuts 1 Driver/Left Frame Mounting Bracket 4 12mm Plastic Washers 1
More informationINSTALLATION INSTRUCTIONS 3063 / FORD F-150
INSTALLATION INSTRUCTIONS 3063 / 3063-2 2009-10 FORD F-150 PARTS LIST: Qty Description Qty Description 1 Grill Guard 4 12mm x 44mm OD Flat Washers 1 Driver/Left Lower Mounting 4 12mm Hex Nut 1 Passenger/Right
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY FRONT BUMPER CHEVY SILVERADO 1500
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Heavy Duty Bumper Assembly 16 12mm Nylon Lock Nuts 1 Driver Mounting Bracket 8 4mm x 10mm Socket Head Screws 1 Passenger Mounting Bracket 4 Sensor Plugs 4 Support
More informationChevy Nova Pro-Touring Front Suspension Installation Instructions
1962-1967 Chevy Nova Pro-Touring Front Suspension Installation Instructions 1-800-984-6259 www.totalcostinvolved.com 1 Pro-Touring Clip A-Arm Assembly Sway Bar Assembly Fender Panel Kit 8 7/16-20 * 1 ¼
More informationINSTALLATION GUIDE PREMIUM FRONT BUMPER FOR RAM AEV30304AA Last Updated: 09/18/17
AEV30304AA Last Updated: 09/18/17 PREMIUM FRONT BUMPER FOR RAM 1500 INSTALLATION GUIDE PLEASE READ BEFORE YOU START To guarantee a quality installation, we recommend reading these instructions thoroughly
More informationDriver/left Corner Fill Panel. Passenger/Right Corner Fill Panel Left and Right Bar Light L Brackets. (2) Plastic Plugs. License Plate Bracket
LD1 FRONT BUMPER PART#R102615 R102618 PARTS LIST: 1 LD1 Bumper Assembly 8 10mm Lock Washers 1 Driver/left Frame Mounting Bracket 8 10mm Hex Nuts 1 Passenger/right Frame Mounting Bracket 2 8-1.25mm x 25mm
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Hidden Winch Mount For 2008 Ford Super Duty Kit 78105 Your safety, and the safety of others, is very important. To help you make informed decisions about safety, we have provided
More information4 th Gen 4 Runner Front Bumper - Installation Instructions:
www.shrockworks.com info@shrockworks.com 877-474-7625 4 th Gen 4 Runner Front Bumper - Installation Instructions: Thank you for purchasing a ShrockWorks product. We are confident you will enjoy it for
More informationINSTALLATION INSTRUCTIONS FOR MOUNTING
INSTALLATION INSTRUCTIONS FOR MOUNTING FRONT PARKING SENSOR RELOCATION BRACKETS ON THE FOLLOWING PROWLER MAX MODEL NOS.: 320713/321610, 310713/321610, 320713/321512 & 310713/321512 ON: (NOTE: TWO 390210
More informationINSTALLATION INSTRUCTIONS For 65800, 65801, 66355, 69250, Rear Bumper And Tire Carrier For Jeep XJ Cherokee
INSTALLATION INSTRUCTIONS For 65800, 65801, 66355, 69250, 69251 Rear Bumper And Tire Carrier For Jeep XJ Cherokee Your safety, and the safety of others, is very important. To help you make informed decisions
More informationINSTALLATION MANUAL. Level of Difficulty. Parts List. Product Image. Tools Required. Notes and Maintenance. Torque Specifications.
INSTALLATION MANUAL Parts List 1 Bull bar 2 Upper frame mounting bracket 1 Driver / left lower frame mounting bracket 1 Passenger / right lower frame mounting bracket 2 Button head bolt, 6mm 4 Flat washer,
More informationINSTALLATION INSTRUCTIONS FOR MOUNTING
INSTALLATION INSTRUCTIONS FOR MOUNTING LUVERNE GRILL GUARDS WITH THE FOLLOWING MODEL NOS.: 330714/330719 & 340714/340719 ON: 2007 AND NEWER CHEVROLET TAHOE, SUBURBAN & AVALANCHE 2007 AND NEWER GMC YUKON
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS APPLICATION: WINCH TRAY, SPORTSMAN GG WINCH TRAY KITS, & HDX GG WINCH TRAY KITS AUTOMOTIVE PRODUCTS, INC. 2015 & UP FORD F-150 APP PART #40-93835, 45-93830, 46-23835, 57-93830,
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS
COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0030 Fits: 2007-10 135i (E82, E88; with N54 engine) 2007-08 335i/xi (E90) 2007-10 335i (E92, E93; with N54 engine) Congratulations for being selective enough
More informationHD BULL NOSE FRONT BUMPER FORD SUPERDUTY F PARTS LIST:
PARTS LIST: 1 HD Bull Nose Bumper Assembly 1 Bumper Cover 1 Winch Tray Bracket Assembly 5 6mm Combo Button Head Bolts (cover) 2 3-hole Bracket Spacer Plates 1 Wrench (6mm Button Head) 2 Plastic Plugs for
More informationINSTALLATION INSTRUCTIONS HD BUMPER AND WINCH MOUNTING KIT Part Number: 74777, Application: 08-NEWER FORD SUPER DUTY WARNING
INSTALLATION INSTRUCTIONS HD BUMPER AND WINCH MOUNTING KIT Part Number: 74777, 76250 Application: 08-NEWER FORD SUPER DUTY Your safety, and the safety of others, is very important. To help you make informed
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationPARTS LIST: ELEVATION BULL NOSE FRONT BUMPER FORD SUPERDUTY F
PARTS LIST: 1 Elevation Bumper Assembly 2 8-1.25mm x 25mm Hex Bolts 1 Winch Tray Bracket Assembly 2 8-1.25mm x 16mm Hex Bolts 2 3-hole Bracket Spacer Plates 6 8mm x 24mm x 2mm Flat Washers 2 Plastic Plugs
More informationSNO-PRO Ford Super Duty F-250, F-350 & F Ford Super Duty F-250, F-350 (With Snow Plow Prep. Package ONLY)
SNO-PRO 000 0 Ford Super Duty F-0, F-0 & F-0 00-00 Ford Super Duty F-0, F-0 (With Snow Plow Prep. Package ONLY) Vehicle Mounting Kit: FK Revised February 0 Curtis Industries Inc. LLC, Higgins St., Worcester,
More informationINSTALLATION INSTRUCTIONS SEMI-HIDDEN WINCH MOUNT Part Number:70005 Application: Ford Super Duty
INSTALLATION INSTRUCTIONS SEMI-HIDDEN WINCH MOUNT Part Number:70005 Application: Ford Super Duty Your safety, and the safety of others, is very important. To help you make informed decisions about safety,
More informationCongratulations on your purchase from Rigid Industries, here are the instructions for installation of your new Rigid Lights.
Congratulations on your purchase from Rigid Industries, here are the instructions for installation of your new Rigid Lights. 20 E-Series LED Light Bar with Cradle for Lower Grill Mount. Dually Fog Lights
More information(W) INSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA / SEQUOIA PART # &
(W) INSTALLATION INSTRUCTIONS PART # 501894 & 501895 PARTS LIST: 1 Grille Guard 4 3/8" Flat Washers 1 Driver/Left Frame 2 3/8" Nylon Lock Nuts 1 Passenger/Right Frame 4 12mm Plastic Washers 1 Driver/Left
More informationCAUTION. INSTALLATION INSTRUCTIONS Part Number Hidden Winch Kit with special XD 9000 Short Drum Winch For Ford F-150 Truck
INSTALLATION INSTRUCTIONS Part Number 69110 Hidden Winch Kit with special XD 9000 Short Drum Winch For Ford F-150 Truck As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message
More informationL Light Bracket Crossbar Light Mount Bracket. Driver/left Support Bracket
PARTS LIST: Qty Description Qty Description 1 Light Bar 4 8-1.25mm x 35mm Hex Bolts 1 Crossbar Light Mount Bracket 6 8-1.25mm x 30mm Hex Bolts 2 Universal s 14 8mm x 24mm x 2mm STD Flat Washers 1 Driver/Left
More informationPlease read BOTH these Installation Instructions and the General Information sheet prior to installing or operating this equipment.
2011-13 Mini Cooper Hardtop (Includes S) 2012-15 Mini Cooper Coupe (Includes S) 2009-15 Mini Cooper Convertible (Includes S) 2012-15 Mini Cooper Roadster (Includes S) 2008-14 Mini Cooper Clubman (Includes
More information(2) License Plate Plugs
PARTS LIST: 1 HD Bull Nose Bumper Assembly 12 12-1.75mm x 50mm 1 Driver/left Frame Mounting Bracket 40 12mm x 37mm OD x 3mm Flat Washers 1 Passenger/right Frame Mounting Bracket 20 12mm Lock Washers 1
More informationINSTALLATION INSTRUCTIONS WINCH MOUNTING KIT Part number: Application: Ford F150 Ecoboost
INSTALLATION INSTRUCTIONS WINCH MOUNTING KIT Part number: 88070 Application: 2011+ Ford F150 Ecoboost GENERAL SAFETY PRECAUTIONS Your safety, and the safety of others, is very important. To help you make
More informationINSTALLATION INSTRUCTIONS ELEVATION FRONT BUMPER DODGE RAM
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Elevation Bumper Assembly 24 12mm x 37mm OD x 3mm Flat Washers 2 Frame Mounting Brackets 12 12mm Nylon Lock Nuts 8 12-1.75mm x 50mm Hex Bolts 2 License Plate Mounting
More informationGM (New Style) 1500 Truck & Tahoe / Yukon 1500 (4x4 With VYU ONLY) Vehicle Mounting Kit: 1FK50
SNO-PRO 3000 2014 - GM (New Style) 1500 Truck & Tahoe / Yukon 1500 (4x4 With VYU ONLY) Vehicle Mounting Kit: 1FK50 Revised 17 September 2015 Curtis Industries LLC, 111 Higgins St., Worcester, MA 01606
More informationLexus NX Fine Mesh and Dynamic Radar Cruise Control Fine Mesh Grilles
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2015-16 Lexus NX Fine Mesh and Dynamic Radar Cruise Control Fine Mesh Grilles Upper Insert - factory chrome surround and emblem reused
More informationMustang GT Splitter Bracket Kit M-17A626-MB INSTALLATION INSTRUCTIONS
!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! Caution: If you are not confident that you can complete the installation safely, have it completed by a certified technician!
More informationMITSUBISHI TRITON MQ (2015 +) AEROSTYLE 4X4 2 POST 3 POST 4 POST 5 POST
INSTALLATION GUIDE BULLBAR MITSUBISHI TRITON MQ (2015 +) AEROSTYLE 4X4 2 POST 3 POST 4 POST 5 POST Version 171010_1 PLEASE READ THE INSTALLATION GUIDE CAREFULLY BEFORE FITTING PRODUCT TO VEHICLE WHEN INSTALLED
More informationINSTALLATION INSTRUCTIONS FOR MOUNTING
INSTALLATION INSTRUCTIONS FOR MOUNTING LUVERNE PROWLER MAX AND BAJA GUARD WITH THE FOLLOWING MODEL NO.: 320930/320933/350931 ON: 2009 AND NEWER DODGE RAM 1500 SERIES TRUCKS 1. READ THE INSTRUCTIONS COMPLETELY
More informationFITTING KIT No s : BULL BAR WINCH ( P/No ) BULL BAR NON WINCH ( P/No )
ARB WINCH / NON WINCH BULL BAR TO SUIT LANDROVER DISCOVERY 2003 ONWARD. FITTING KIT No s :- 617 1793 BULL BAR WINCH ( P/No 343 2120 ) 617 1794 BULL BAR NON WINCH ( P/No 323 2120 ) WARNING FOR VEHICLES
More informationINSTALLATION INSTRUCTIONS
Read instructions fully before commencing fitment. Left hand & Right hand components are determined as seated in the vehicle. Check for (& remove) any build up in all captive nuts fitted to the Bumper.
More informationLexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2013-15 Lexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements Part #1372-0102-13 / Black Ice
More informationINSTALLATION INSTRUCTIONS FRONT RUNNER GRILLE GUARD 2015 TRANSIT VAN (FULL SIZE)
INSTALLATION INSTRUCTIONS FRONT RUNNER GRILLE GUARD PARTS LIST: 1 Runner Grille Guard Center 6 12mm Lock Washers 1 Driver/Left Modular Wing 6 12mm Hex Nuts 1 Passenger/Right Modular Wing 2 8-1.25mm x 40mm
More informationINSTALLATION INSTRUCTIONS JEEP WRANGLER PART# 1050 /
INSTALLATION INSTRUCTIONS 2007-12 JEEP WRANGLER PART# 1050 / 1050-2 PARTS LIST: Qty Description Qty Description 1 Aries Grill guard 10 12mm Lock washers 1 Driver/left mounting bracket 10 12mm Hex nuts
More informationINSTRUCTIONS INSTRUCCIONES CONSIGNES
AUTOMOTIVE PRODUCTS, INC. INSTRUCTIONS INSTRUCCIONES CONSIGNES APPLICATION: 2013-UP FORD ESCAPE APP PART # 28-21010, 28-21015 STYLIZED RUNNING BOARD ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 2 RUNNING BOARDS
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 2011 Dodge Charger Road Defender 5000 Series Push Bumper Part Number 5076 Do not attempt to install this product on any vehicle other than the one it is designed for and listed
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INC. INSTALLATION INSTRUCTIONS APPLICATION: 2013-2015 DODGE RAM 1500 SSV PUSH BAR ELITE XD APP PART #: 36-53545 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 PUSH BAR ASSEMBLY RATCHET
More informationCHEVROLET/GMC K K K3500 4X BLAZER/JIMMY 4X ATTACHMENT KIT
6-203 August, 2003 1988-1999 CHEVROLET/GMC K1500 - K2500 - K3500 4X4 1992-1994 BLAZER/JIMMY 4X4 81001 ATTACHMENT KIT PARTS LIST ITEM STOCK DESCRIPTION QTY. ITEM STOCK DESCRIPTION QTY. 81001 MOUNTING CARTON
More informationUSE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT:
1962-1967 Chevy Nova Pro-Touring Front Suspension Installation Instructions Tech line: 1-855-693-1259 www.totalcostinvolved.com Read and understand these instructions before starting any work! USE THE
More informationHiniker Company th St. P.O. Box 3407 Mankato, MN 56002
VEHICLE INSTALLATION INSTRUCTIONS FOR: FORD 4x4: 008-06 SUPER DUTY F50-350 - 450-550 Page of 5 Hiniker Company 58766 40th St. P.O. Box 3407 Mankato, MN 5600 INSTRUCTION SHEET NO: 50370 Rev. B September
More information06-08 Passenger/Right Top Mounting Bracket Driver/Left Top. Mounting Bracket. Driver/Left Frame Mounting Bracket
PARTS LIST: 1 Grille Guard 4 12mm x 44mm OD x 3mm Flat Washers 1 Driver/Left Frame Mounting Bracket 12 12mm x 32mm OD x 3mm Flat Washers 1 Passenger/Right Frame Mounting Bracket 4 12mm Lock Washers 1 Driver/Left
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS POLICE PUSH BAR ELITE XD APPLICATION: 015-018 Ford F-150 PART NUMBER: 3-505 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 GRILLE GUARD ASSEMBLY 1MM SOCKET,3 LOWER MOUNTING BRACKET,
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
2011-13 Mini Cooper Hardtop (Includes S) 2012-14 Mini Cooper Coupe (Includes S) 2009-15 Mini Cooper Convertible (Includes S) 2012-14 Mini Cooper Roadster (Includes S) 2008-14 Mini Cooper Clubman (Includes
More information09-12 Dodge 4WD Leveling Kit
9235900 09-12 Dodge 4WD 1500 2.5 Leveling Kit Thank you for choosing Rough Country for all your suspension needs. DOES NOT FIT TRX PACKAGE VEHICLES!! Rough Country recommends a certified technician install
More informationSNO-PRO GM Silverado / Sierra 2500, 3500 New Style (With Snow Plow Prep. ONLY)
SNO-PRO 3000 2011 - GM Silverado / Sierra 2500, 3500 New Style (With Snow Plow Prep. ONLY) Vehicle Mounting Kit: 1FK47 Revised 15 February 2011 Curtis Industries Inc. LLC, 111 Higgins St., Worcester, M
More informationBASEPLATE KIT INSTALLATION INSTRUCTIONS
Item Qty. Length Width Name Part No. 1... 4... 30mm... 10mm... 10mm x 1.5 x 30mm... 356101-00 2... 8... 10mm... 10mm FENDER WASHER... 355716-00 3... 4... 10mm... 10mm x 1.5 NUT... 356230-00 4... 4... 10mm...
More informationWildcat System Instructions
Wildcat System Instructions NOTE: Most steps contained in these instructions will need to be repeated on the other side of the vehicle. Prior to assembly of windshield it is necessary to establish what
More informationINSTALLATION INSTRUCTIONS ELITE SERIES REAR BUMPER AND TIRE CARRIER Part Number: 89525/89800 Application: Jeep JK
INSTALLATION INSTRUCTIONS ELITE SERIES REAR BUMPER AND TIRE CARRIER Part Number: 89525/89800 Application: 2007+ Jeep JK GENERAL SAFETY PRECAUTIONS Your safety, and the safety of others, is very important.
More informationINSTALLATION INSTRUCTIONS ELITE SERIES REAR BUMPER AND TIRE CARRIER Part Number: 89525/89800 Application: Jeep JK
INSTALLATION INSTRUCTIONS ELITE SERIES REAR BUMPER AND TIRE CARRIER Part Number: 89525/89800 Application: 2007+ Jeep JK GENERAL SAFETY PRECAUTIONS Your safety, and the safety of others, is very important.
More informationFor CJ ( ) installation, please refer to instructions starting on page 3.
976-006 Jeep CJ, Wrangler XHD Bumper 56.0 Contents:. M x 60 HHCS. M Washer 3. D-Ring. Side Frame Bracket 5. Nut Plate 6. Sub-Frame 7. Bumper 8. M x 35 HHCS 9. M0 Self-Tapping Bolt* Quantity: 8 3 5 6 7
More informationbaseplate Chevrolet Equinox
, Rev 3 06/16 baseplate 9518316 Chevrolet Equinox Pin height - 14-3/4 Centers - 24-1/4 25. ITEM PART # QTY DESCRIPTION 1 00057 2.25 LOCKWASHER 2 00059 8.375 FLATWASHER 3 00060 24.375 LOCKWASHER 4 00061
More informationINSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS
June 2004 INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS Please be sure that this document is given to the end user of this product. It contains many important items relating to the proper usage of
More informationPORTA-DOCK, INC. 65A 1155 DOUBLE PERSONAL WATERCRAFT LIFT
Page 1 of 9 PORTA-DOCK, INC. 65A 1155 DOUBLE PERSONAL WATERCRAFT LIFT Thank you for purchasing our product! Please read these instructions and follow them step by step.* STEP 1. Separate and group like
More informationDriver/Left Mounting Bracket. Passenger/Right Mounting Bracket. Bolt Plates
PARTS LIST: 1 Bull Bar 6 12-1.75mm Nylon Lock Nut 1 Driver/Left Mounting Bracket 4 Bolt Assembly 1 Passenger/Right Mounting Bracket 1 LED Light Bar with mounting bolts 2 12x1.75mm x 30mm Double 2 12 x
More informationI-Sheet Number Rev.B 3-1/2 OVAL BULL BAR DODGE RAM 1500
PARTS LIST: 1 Bull Bar 2 10-1.5mm x 35mm Hex Bolts 2 Tube Brackets (Bull Bar) passenger or driver side 2 10mm Lock Washers 2 Upper Frame Brackets (models w/o tow hooks only) 4 10mm x 27mm OD x 3mm Flat
More information***Be sure that the loaded trailer weight does not exceed 24,000 lbs. or the vertical load rating does not exceed 6000 lbs.
April 2006 INSTALLATION INSTRUCTIONS MODEL NO. 70680 07068 24K 5th Wheel with Heavy Duty EZ-ROLLER For use on shortbed P/U applications US Pat. No. 6247720 PARTS INCLUDE: 1. 1675-07 Head Assembly (1) 15.
More informationINSTALLATION INSTRUCTIONS HD BUMPER AND WINCH MOUNTING KIT Part Number: 70650, 70651, Application: 05-NEWER FORD SUPER DUTY WARNING
INSTALLATION INSTRUCTIONS HD BUMPER AND WINCH MOUNTING KIT Part Number: 70650, 70651, 73990 Application: 05-NEWER FORD SUPER DUTY Your safety, and the safety of others, is very important. To help you make
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationP3066 INSTALLATION MANUAL
P3066 INSTALLATION MANUAL Parts List 1 Grille guard 1 Driver / left frame bracket Level of Difficulty Moderate Scan for helpful install tips 1 Passenger / right frame bracket 1 Driver / left top bracket
More information2011 Honda Accord Coupe Fine Mesh Grille
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! TOOLS REQUIRED 2011 Honda Accord Coupe Fine Mesh Grille Replacement Upper / Lower Overlay Part #: Complete #1124-0102-11 / Black Ice
More informationDetroit Speed, Inc. Rear QUADRAlink Conversion Kit Camaro/Firebird P/N:
Detroit Speed, Inc. Rear QUADRAlink Conversion Kit 1982-92 Camaro/Firebird P/N: 041721 The Detroit Speed Inc. QUADRAlink Conversion Kit, eliminates the factory torque arm configuration. It features no-compromise
More informationDriver Side Support Bracket pictured in "no-tow hook" direction. Reverse direction for tow hook equipped vehicles
PARTS LIST: 1 Bull Bar 2 10-1.5mm x 35mm Hex Bolts 2 Tube Brackets (Bull Bar) passenger or driver side 2 10mm Lock Washers 2 Upper Frame Brackets (models w/o tow hooks only) 4 10mm x 27mm OD x 3mm Flat
More informationToyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Transmission cooler relocation brackets Torque Wrench
2016-2017 Toyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Items Included: Small flat head screw driver Winch Mount Ratchet, 10mm, 12mm, 14mm, 17mm & Skid Plate 19mm sockets Transmission
More informationInstallation Instructions BX1641 Monte Carlo SS
Installation Instructions BX1641 Monte Carlo SS 2000-03 Serial No. The front bumper and headlights are removed for baseplate installation. The lower plastic rock guard is temporarily removed from the front
More information09-12 Dodge 4WD /4 Body Lift
92RC80000 09-12 Dodge 4WD 1500 1 1/4 Body Lift Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this kit. Attempts to install
More informationTESLA MODEL S REAR UNDER SPOILER & DIFFUSER SYSTEM
TESLA MODEL S Thank you for purchasing your Unplugged Performance Rear Under Spoiler & Diffuser System for the Tesla Model S! Please read this manual carefully prior to installation. REAR UNDER SPOILER
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS OUTLAW FRONT BUMPER APPLICATION: 2013-2018 Dodge Ram 1500 PART NUMBER: 58-61025 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 OUTLAW FRONT BUMPER 18MM WRENCH 2 1 UPPER SKID PLATE
More informationmm Hex Nuts. (2) 10mm x 35mm Bolt Plates
PARTS LIST: SPORT BAR 1 Sport Bar 8 12mm x 24mm OD x 2.5mm STD Flat Washers 1 Driver/Left Frame 6 12mm Lock Washers 1 Passenger/Right Frame 4 12-1.75mm Hex Nuts 1 Driver/Left Tube 2 10-1.50mm x 30mm Hex
More information20964/B 20964/B 2014 TOYOTA TUNDRA TUNDRA. Billet Grille. Fig 1. Fig 2
Billet Grille TOOLS REQUIRED: PARTS LIST: Socket Set (6) U-Nuts Flat/Phillips Screw Drivers (8) #10 Screws Pliers (2) #8 Screws ¾ (2) 2 Flange Bracket (1) Top Plate Overlay Bracket - driver (1) Top Plate
More informationSubaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI
Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following
More information