Propeller Assembly. 1. General

Size: px
Start display at page:

Download "Propeller Assembly. 1. General"

Transcription

1 Propeller Assembly GENERAL 61-10: PROPELLER ASSEMBLY 1. General The propeller assembly consists of a hollow aluminum hub which supports the propeller blades and also houses the pitch changing mechanism. Movement of propeller blades is controlled by a hydraulic piston/cylinder combination mounted on the front of the hub. Serials w/ Hartzell Propeller: The linear motion of the hydraulic piston is transmitted to each blade through a pitch change rod and fork. A pitch change knob at the base of each blade intersects with the fork. Serials w/ McCauley propeller: The linear motion of the hydraulic piston is transmitted to each blade through a piston rod, linkage assembly, and actuating pin. The actuating pin assembly is secured to the base of each blade with screws. Blade pitch is controlled by the governor. The governor supplies oil to the propeller hub to move the blades toward high pitch position (decreased RPM). Conversely, the propeller blades move toward low pitch position (increase RPM) as the governor drains oil away from the propeller hub. A mechanical spring is installed within the propeller to assist movement of the blades to a lower pitch position as RPM decays since blade centrifugal twisting moment is only present when the propeller is rotating. The mechanical spring will ensure that blade angle will reach the low pitch stop when the propeller is static. If oil pressure is lost at any time, the propeller will move to low pitch. The propeller assembly employs high-strength, aluminum or composite blades. An aluminum or composite spinner assembly enhances the appearance of the propeller and streamlines air flow over the propeller to improve performance. The spinner dome attaches to a spinner bulkhead at the rear of the propeller hub. It is essential that the propeller assembly be maintained in accordance with vendor recommended service procedures. Refer to the manufacturer s approved Instructions For Continued Airworthiness. 1

2 . Maintenance Practices A. Propeller - Serials w/ Hartzell Propeller (See Figure ) Ensure master and magneto switches are off, and ignition key is removed. (1) Removal - Propeller (a) Acquire necessary tools, equipment, and supplies. (b) Remove key from ignition. (c) Set BAT 1, BAT, and AVIONICS switches to OFF positions. (d) Move fuel selector to OFF position. (e) Place mixture control in idle cut-off. (f) Remove engine cowling. (Refer to 1-10) (g) (h) (i) (j) (k) (l) Description P/N or Spec. Supplier Purpose Hoist - Any Source Hoist propeller. Sling - Any Source Secure propeller to hoist. Drain Pan - Any Source Receive waste lubricant. To ensure spinner dome is reinstalled in same clocked position, draw a reference line across spinner dome and spinner bulkhead. Remove screws and washers securing spinner dome to spinner bulkhead. Remove spinner dome from airplane. Position hoist and lifting sling forward of airplane and attach sling to propeller. Place a drain pan beneath propeller to catch any spilled lubricant. Serials w/ Ice Protection: Remove bolt, washer, clamp, and nut securing slinger ring feed tube to bracket on engine baffle and remove feed tube nozzle from inside of slinger ring. Loosen and remove nuts and washers securing propeller to engine flange.

3 (m) (n) (o) (p) (q) Note orientation of propeller blades to engine to ensure propeller is reinstalled in correct clock position. Remove propeller from engine flange with care to prevent damaging the propeller mounting studs. Remove propeller from airplane. Serials w/ Ice Protection: Remove bolts, p-clips, washers, and nuts securing feed tubes to propeller hub. To ensure spinner bulkhead is reinstalled in same clocked position, draw a reference line across spinner bulkhead and propeller hub. Remove bolts, spacers, washers, and nuts securing spinner bulkhead to propeller hub. Remove O-ring from groove inside hub at flange mounting and discard. Remove drain pan and discard spilled lubricant. () Installation - Propeller (a) Acquire necessary tools, equipment, and supplies. Description P/N or Spec. Supplier Purpose Hoist - Any Source Hoist propeller. Sling - Any Source Secure propeller to hoist. Degreaser - Any Source Degrease components. O-Ring C Hartzell Propellers Inc. Sealing component for Hartzell propeller. (b) Apply a light coat of engine oil to new O-ring and bore surfaces of propeller. Insert O-ring into groove inside hub at flange mounting. Verify spinner bulkhead is in same clocked position as originally installed. 3

4 (c) (d) (e) (f) (g) (h) (i) (j) (k) Serials w/ Standard Weight Hub: Position spinner bulkhead to propeller hub and secure with bolts, spacers, washers, and nuts. Torque nuts 0 to ft-lb (.1 to 9.8 Nm). (Refer to 0-60) Serials w/ Light Weight Hub: Position spinner bulkhead to propeller hub and secure with bolts, spacers, washers, and nuts. Torque nuts 4 to 6 ft-lb (3.5 to 35. Nm). (Refer to 0-60) Serials w/ Ice Protection: Install bolts, p-clips, washers, and nuts securing blade feed tubes to propeller hub. Clean the engine shaft, propeller flange, and engine flange. Verify propeller is in same clocked position as originally installed. Care must be taken to avoid damaging hub or O-ring when installing propeller. Do not attempt to forcefully draw propeller onto engine flange with nuts. Using hoist and sling, align dowel pins in propeller flange with corresponding holes in engine mounting flange. Tighten nuts evenly to avoid hub damage. Install washers and nuts securing propeller to engine flange. Torque nuts 0 to 80 ft-lb (94.9 to Nm). (Refer to 0-60) Serials w/ Ice Protection: Position slinger ring feed tube to engine baffling bracket and to inside of slinger ring. Install bolt, washer, clamp, and nut securing feed tube to engine baffling. Verify spinner dome is in same clocked position as originally installed. Position spinner dome to front of propeller hub and secure to spinner bulkhead with screws and washers. Serials w/ Ice Protection: Check feed tube alignment. 1 Perform Inspection/Check - Blade Feed Tube Orientation. (Refer to 30-60) Perform Inspection/Check - Slinger Ring Feed Tube Orientation. (Refer to 30-60) (l) Install engine cowling. (Refer to 1-10) 4

5 Figure : Propeller Installation - Serials w/ Hartzell Propeller ENGINE PROP FLANGE (REF) NOTE Serials w/ Regular Weight Hub: Torque nuts to 0 - ft-lb ( Nm). Serials w/ Light Weight Hub: Torque nuts to 4-6 ft-lb ( Nm). Torque nuts to 50-0 in-lb ( Nm). Torque nuts to 0-80 ft-lb ( Nm) Serials w/ composite spinner. LEGEND 1. Spinner. Washer 3. Screw 4. Propeller Stud 5. O-ring 6. Spinner Bulkhead. Nut 8. Spacer 9. Propeller 10. Bolt 11. Feed Tube 1. P-Clip 13. Sealing Ring 14. Standoff 15. Slinger Ring 16. Bonded Seal 1. Propeller Boot, De-Ice 18. Wave Washer SR_MM61_5139 5

6 B. Propeller - Serials w/ McCauley propeller (See Figure ) Ensure master and magneto switches are off, and ignition key is removed. (1) Removal - Propeller (a) Acquire necessary tools, equipment, and supplies. (b) Remove key from ignition. (c) Set BAT 1, BAT, and AVIONICS switches to OFF positions. (d) Move fuel selector to OFF position. (e) Place mixture control in idle cut-off. (f) Remove engine cowling. (Refer to 1-10) (g) (h) (i) (j) (k) (l) (m) Description P/N or Spec. Supplier Purpose Hoist - Any Source Hoist propeller. Sling - Any Source Secure propeller to hoist. Drain Pan - Any Source Receive waste lubricant. To ensure spinner dome is reinstalled in same clocked position, draw a reference line across spinner dome and spinner bulkhead. Remove screws and washers securing spinner dome to spinner bulkhead. Remove spinner dome from airplane. Remove spinner support and shim(s) from front of propeller hub. Position hoist and lifting sling forward of airplane and attach sling to propeller. Place a drain pan beneath propeller to catch any spilled lubricant. Serials w/ Ice Protection: Remove bolt, washer, clamp, and nut securing slinger ring feed tube to bracket on engine baffle and remove feed tube nozzle from inside of slinger ring. Loosen and remove nuts securing propeller to engine flange. Note orientation of propeller blades to engine to ensure propeller is reinstalled in correct clock position. 6

7 (n) (o) (p) (q) (r) Remove propeller from engine flange with care to prevent damaging the propeller mounting studs. Remove propeller from airplane. Serials w/ Ice Protection: Remove screws, washers, clamps, and nuts securing blade feed tubes to feed tube brackets. To ensure spinner bulkhead assembly is reinstalled in same clocked position, draw a reference line across spinner bulkhead assembly and propeller hub. Remove screws and washers securing spinner bulkhead assembly to propeller hub. Remove O-ring from groove inside hub at flange mounting and discard. Remove drain pan and discard spilled lubricant. () Installation - Propeller (a) Acquire necessary tools, equipment, and supplies. Description P/N or Spec. Supplier Purpose Hoist - Any Source Hoist propeller. Sling - Any Source Secure propeller to hoist. Degreaser - Any Source Degrease components. O-Ring A McCauley Propeller Systems Sealing component for McCauley propeller. Lubricant MIL-T Any Source Lubricate mounting studs and nuts on McCauley propeller. (b) Apply a light coat of engine oil to new O-ring and bore surfaces of propeller. Insert O-ring into groove inside hub at flange mounting. Verify spinner bulkhead assembly is in same clocked position as originally installed.

8 (c) (d) (e) (f) (g) (h) (i) (j) (k) Position spinner bulkhead to propeller hub and secure with screws and washers. Torque screws 5 to 85 in-lb (0.53 to 0.60 Nm). Safety wire screws in pairs. (Refer to 0-60) (Refer to 0-50) Serials w/ Ice Protection: Install screws, washers, clamps, and nuts securing feed tubes to feed tube brackets. Clean the engine shaft, propeller flange, and engine flange. Verify propeller is in same clocked position as originally installed. Care must be taken to avoid damaging hub or O-ring when installing propeller. Do not attempt to forcefully draw propeller onto engine flange with nuts. Using hoist and sling, align dowel pins in propeller flange with corresponding holes in engine mounting flange. Never use oil as a substitute for approved lubricant. Substitution of the approved grease with an unapproved lubricant (or no lubricant) could result in undertorquing or severe overtorquing of propeller attaching parts. Liberally apply lubricant to threads of studs and threads and faces of nuts. Install nuts securing propeller assembly to engine flange. Tighten nuts evenly to avoid hub damage. Secure propeller to engine flange and torque nuts 45 to 50 ft-lb (61.0 to 6. Nm). (Refer to 0-60) Serials w/ Ice Protection: Position slinger ring feed tube to engine baffling bracket and to inside of slinger ring. Install bolt, washer, clamp, and nut securing feed tube to engine baffling. Verify spinner dome is in same clocked position as originally installed. Position spinner support and shim(s) to front of propeller hub. NOTE Spinner installation holes should be approximately 0.05 inch (1. mm) from true alignment when shims are correctly adjusted. Lightly press spinner shell snug against support and check alignment of holes in bulkhead. 8

9 (l) (m) Pushing hard on shell, align installation holes with bulkhead. Secure spinner shell to spinner bulkhead with four equally spaced screws and washers. Relax force against shell and install remaining screws and washers. Serials w/ Ice Protection: Check feed tube alignment. 1 Perform Inspection/Check - Blade Feed Tube Orientation. (Refer to 30-60) Perform Inspection/Check - Slinger Ring Feed Tube Orientation. (Refer to 30-60) (n) Install engine cowling. (Refer to 1-10) 9

10 Figure : Propeller Installation - Serials w/ McCauley propeller ENGINE PROP FLANGE (REF) LEGEND 1. Spinner. Washer 3. Screw 4. Propeller Stud 5. O-ring 6. Spinner Bulkhead. Nut 8. Spacer 9. Propeller 10. Bolt 11. Feed Tube 1. Slinger Ring 13. Propeller Boot, De-Ice 14. Support 15. Shim 16. Adapter 1. Backing Plate 18. Bracket NOTE Apply lubricant to threads of studs and threads and faces of nuts. Torque nuts to ft-lb ( Nm). Torque screws to 5-80 in-lb ( Nm). Torque nuts to in-lb ( Nm). SR_MM61_

11 C. Adjustment/Test - Dynamic Balance Dynamic balancing reduces vibration produced by the propeller and powerplant. Small balance weights are added to the propeller/crankshaft assembly to correct for errors in mass distribution so vibration is reduced. Refer to the manufacturer's Instructions for Continued Airworthiness for pertinent information regarding dynamic balancing. D. Inspection/Check - Blade Track Blade track is the way one rotating blade tip follows the other in almost the same plane. Excessive difference in blade track may be an indication of bent blades or improper propeller installation. Refer to the manufacturer's Instructions for Continued Airworthiness for pertinent information regarding blade track. E. Inspection/Check - Loose Blades Although blades should be tight in the propeller, slight movement is acceptable if blade returns to original position when released. Blades with excessive movement, or that do not return to original position when released may indicate internal wear or damage. Refer to the manufacturer's Instructions for Continued Airworthiness for pertinent information regarding loose blades. F. Cleaning/Painting Propeller blades are painted with a durable specialized coating that is resistant to abrasion. If this coating becomes eroded, it is necessary to re-paint the blades to provide proper corrosion and erosion protection. Refer to the manufacturer's Instructions for Continued Airworthiness for pertinent information regarding painting. G. Repairs Nicks, gouges, and scratches on blade surfaces or on leading or trailing edges must be removed prior to flight. Refer to the manufacturer's Instructions for Continued Airworthiness for pertinent information regarding repairs. 11

12 Intentionally Left Blank 1

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL PROPELLER 1. GENERAL The airplane employs a 3 blade, constant speed, non-feathering propeller. The blades (composite or aluminum) are mounted in an aluminum hub which contains the pitch changing mechanism

More information

C I R R U S PROPELLER GENERAL

C I R R U S PROPELLER GENERAL PROPELLER 1. GENERAL The airplane employs a 3 blade, constant speed, non-feathering propeller. The blades (composite or aluminum) are mounted in an aluminum hub which contains the pitch changing mechanism

More information

SERVICE KIT. TITLE McCAULEY 2A34C203/90DCA-2 TWO BLADED THREADLESS PROPELLER INSTALLATION

SERVICE KIT. TITLE McCAULEY 2A34C203/90DCA-2 TWO BLADED THREADLESS PROPELLER INSTALLATION TITLE McCAULEY 2A34C203/90DCA-2 TWO BLADED THREADLESS PROPELLER INSTALLATION EFFECTIVITY: The following airplanes that are in a landplane, ski plane, seaplane, or amphibian configuration. MODEL SERIAL

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL ELEVATOR AND PITCH TRIM SYSTEM 1. DESCRIPTION This section describes that portion of the flight control system which controls the position and movement of the elevator. Included are; elevator system torque

More information

HARTZELL PROPELLER INC.

HARTZELL PROPELLER INC. HARTZELL PROPELLER INC. One Propeller Place Piqua, Ohio 45356-2634 U.S.A. Telephone: 937.778.4200 Fax: 937.778.4391 MANUAL REVISION TRANSMITTAL Manual (61-00-11) Propeller Owner's Manual and Logbook REVISION

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL MODEL SR0 YAW CONTROL AND TRIM. GENERAL This section describes that portion of the flight control system which controls the position and movement of the rudder. Included are; rudder system rigging, rudder

More information

pages 4-1 thru 4-4 pages 4-1 thru 4-4

pages 4-1 thru 4-4 pages 4-1 thru 4-4 HARTZELL PROPELLER INC. One Propeller Place Piqua, Ohio 45356-2634 U.S.A. Telephone: 937.778.4200 Fax: 937.778.4391 MANUAL REVISION TRANSMITTAL Manual (61-00-15) Propeller Owner's Manual and Logbook REVISION

More information

Yaw Control and Trim. 1. General. A. Yaw Control System. B. Yaw Trim System

Yaw Control and Trim. 1. General. A. Yaw Control System. B. Yaw Trim System CIRRUS AIRPLANE MAINTENANCE MANUAL MODELS SR AND SRT Yaw Control and Trim CHAPTER 7-0: YAW CONTROL AND TRIM GENERAL 7-0: YAW CONTROL AND TRIM. General This section describes that portion of the flight

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL POWER PLANT 1. GENERAL This chapter describes maintenance practices for the airplane systems which provide the means to induce and convert fuel-air mixture into power such as the engine, baffling, cowling,

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL INDICATING 1. DESCRIPTION This section describes that portion of the oil system which is used to indicate the quantity, temperature, and pressure of the oil. Components included are the oil filler cap/dipstick,

More information

C I R R U S COWLING DESCRIPTION

C I R R U S COWLING DESCRIPTION COWLING 1. DESCRIPTION Serials 22-0002 thru 22-019, 22-0821 thru 22-711: The engine cowling, fabricated from fiberglass and epoxy, consists of one upper and two lower halves. A one-piece (22-0002 thru

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL POWER CONTROL. DESCRIPTION This section describes those components which furnish a means of controlling engine power. Engine controls for the airplane include the following: control quadrant, throttle

More information

Flaps System. 1. General

Flaps System. 1. General CIRRUS AIRPLANE MAINTENANCE MANUAL Flaps System CHAPTER 27-50: FLAPS SYSTEM GENERAL 27-50: FLAPS SYSTEM 1. General This section describes that portion of the flight control system which controls the position

More information

WHIRLWIND. Owner s Manual 151H Series (Rev ) Model: 151H Serial Number: Manufacture Date: A V I A T I O N WHIRL WIND AVIATION

WHIRLWIND. Owner s Manual 151H Series (Rev ) Model: 151H Serial Number: Manufacture Date: A V I A T I O N WHIRL WIND AVIATION WHIRLWIND A V I A T I O N M a nufacturer of Composite Constant Speed P r o pellers Model: 151H Serial Number: Manufacture Date: Owner s Manual 151H Series (Rev 2014-2) WHIRL WIND AVIATION 1419 STATE ROUTE

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL AIR INTAKES 1. DESCRIPTION This section describes that portion of the power plant which directs mass air flow to the engine. Induction air enters the engine through a filter mounted on the left, forward

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL ELECTRICAL LOAD DISTRIBUTION. DESCRIPTION The power distribution system for this airplane consists of the main distribution bus and the essential distribution bus in the MCU along with the associated buses

More information

WHIRLWIND. Owner s Manual Series (Rev ) Serial Number: Manufacture Date: A V I A T I O N Model: WHIRL WIND AVIATION

WHIRLWIND. Owner s Manual Series (Rev ) Serial Number: Manufacture Date: A V I A T I O N Model: WHIRL WIND AVIATION WHIRLWIND A V I A T I O N Model: 100-4 Serial Number: 100-4- Manufacture Date: M a nufacturer of Composite Constant Speed P r o pellers Owner s Manual 100-4 Series (Rev 2014-2) WHIRL WIND AVIATION 1419

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL AIR INTAKES 1. DESCRIPTION This section describes that portion of the power plant which directs mass air flow to the engine. Induction air enters the engine through a filter mounted on the right, aft side

More information

Pitch Control and Trim

Pitch Control and Trim Pitch Control and Trim GENERAL 27-30: PITCH CONTROL AND TRIM. General This section describes that portion of the flight control system which controls the position and movement of the elevator. This includes

More information

TUBES, HOSES, AND FITTINGS

TUBES, HOSES, AND FITTINGS TUBES, HOSES, AND FITTINGS 1. DESCRIPTION This section contains instructions and specifications for aircraft system plumbing and fittings. Page 1 2. MAINTENANCE PRACTICES A. Ice Protection System Compression

More information

WHIRLWIND. Owner s Manual 400C-M14 Series (Rev ) Model: 400C-M14 Serial Number: Manufacture Date: A V I A T I O N WHIRL WIND AVIATION

WHIRLWIND. Owner s Manual 400C-M14 Series (Rev ) Model: 400C-M14 Serial Number: Manufacture Date: A V I A T I O N WHIRL WIND AVIATION WHIRLWIND A V I A T I O N M a nufacturer of Composite Constant Speed P r o pellers Model: 400C-M14 Serial Number: Manufacture Date: Owner s Manual 400C-M14 Series (Rev 2014-2) WHIRL WIND AVIATION 1419

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL NOISE SUPPRESSOR 1. DESCRIPTION Noise suppression is accomplished through use of a heat exchanger (Serials 0002 thru 019) or a heat exchanger and muffler (Serials 020 & subs) connected to the exhaust header

More information

C I R R U S CONTROLLING DESCRIPTION

C I R R U S CONTROLLING DESCRIPTION CONTROLLING 1. DESCRIPTION Serials 22-0002 & subs: An electric two-speed fuel pump provides boost (low speed) and prime (high speed) for the engine. A console mounted rocker switch located on the center

More information

WHIRLWIND. Owner s Manual 375RV Series (Rev ) Model: 375RV Serial Number: 375RV- Manufacture Date: A V I A T I O N WHIRL WIND AVIATION

WHIRLWIND. Owner s Manual 375RV Series (Rev ) Model: 375RV Serial Number: 375RV- Manufacture Date: A V I A T I O N WHIRL WIND AVIATION WHIRLWIND A V I A T I O N M a nufacturer of Composite Constant Speed P r o pellers Model: 375RV Serial Number: 375RV- Manufacture Date: Owner s Manual 375RV Series (Rev 2014-3) WHIRL WIND AVIATION 1419

More information

53-40 ATTACH FITTINGS

53-40 ATTACH FITTINGS ATTACH FITTINGS. DESCRIPTION Attach fittings are provided for attachment of the seats (Refer to -0), baggage straps (Refer to -0), rear seat harnesses (Refer to -0), cargo net straps (Refer to -0), cabin

More information

HARTZELL PROPELLER INC.

HARTZELL PROPELLER INC. HARTZELL PROPELLER INC. One Propeller Place Piqua, Ohio 45356-2634 U.S.A. Telephone: 937.778.4200 Fax: 937.778.4391 MANUAL REVISION TRANSMITTAL Manual (61-00-49) Propeller Owner's Manual and Logbook REVISION

More information

C I R R U S DISTRIBUTION DESCRIPTION

C I R R U S DISTRIBUTION DESCRIPTION MODELS SR AND SRT DISTRIBUTION. DESCRIPTION This section contains information on the distribution system. The fuel distribution system consists of electric and mechanical (engine-driven) fuel pumps, fuel

More information

HARTZELL PROPELLER INC.

HARTZELL PROPELLER INC. HARTZELL PROPELLER INC. One Propeller Place Piqua, Ohio 45356-2634 U.S.A. Telephone: 937.778.4200 Fax: 937.778.4391 MANUAL REVISION TRANSMITTAL Manual (61-00-39) Propeller Owner's Manual and Logbook REVISION

More information

WHIRLWIND. Owner s Manual 200C / 400C Series (Rev ) Model: Serial Number: Manufacture Date: A V I A T I O N WHIRL WIND AVIATION

WHIRLWIND. Owner s Manual 200C / 400C Series (Rev ) Model: Serial Number: Manufacture Date: A V I A T I O N WHIRL WIND AVIATION WHIRLWIND A V I A T I O N M a nufacturer of Composite Constant Speed P r o pellers Model: Serial Number: Manufacture Date: Owner s Manual 200C / 400C Series (Rev 2014-2) WHIRL WIND AVIATION 1419 STATE

More information

SERVICE LETTER. Model 1A162 Propeller, and the McCauley Fixed Pitch Propeller Service Manual.

SERVICE LETTER. Model 1A162 Propeller, and the McCauley Fixed Pitch Propeller Service Manual. September 4, 2009 TITLE MODEL 1A162/TCD6754 PROPELLER SERVICE INFORMATION UPDATE TO: FAA-Approved Propeller Repair Stations, Aircraft Manufacturers, Owners and Operators EFFECTIVITY Model 1A162 Propeller,

More information

WHIRLWIND. Owner s Manual 400 Rocket Series (Rev ) Model: 400 Rocket Serial Number: Manufacture Date: A V I A T I O N WHIRL WIND AVIATION

WHIRLWIND. Owner s Manual 400 Rocket Series (Rev ) Model: 400 Rocket Serial Number: Manufacture Date: A V I A T I O N WHIRL WIND AVIATION WHIRLWIND A V I A T I O N M a nufacturer of Composite Constant Speed P r o pellers Model: 400 Rocket Serial Number: Manufacture Date: Owner s Manual 400 Rocket Series (Rev 2014-2) WHIRL WIND AVIATION 1419

More information

Seabee Annual Inspection Procedures

Seabee Annual Inspection Procedures Procedures Due to the wide variety of Seabee s flying out there, these procedures should be modified to fit YOUR Seabee. Make sure that all AD s are complied with as well as any required Service Bulletins

More information

MANUAL REVISION TRANSMITTAL Manual 147 ( ) Propeller Owner's Manual and Logbook REVISION 13 dated July 2017

MANUAL REVISION TRANSMITTAL Manual 147 ( ) Propeller Owner's Manual and Logbook REVISION 13 dated July 2017 HARTZELL PROPELLER INC. One Propeller Place Piqua, Ohio 45356-2634 U.S.A. Telephone: 937.778.4200 Fax: 937.778.4215 MANUAL REVISION TRANSMITTAL Manual (61-00-47) Propeller Owner's Manual and Logbook REVISION

More information

C I R R U S COLLECTOR DESCRIPTION

C I R R U S COLLECTOR DESCRIPTION COLLECTOR 1. DESCRIPTION This section describes the portion of the exhaust system which collects the exhaust gases from the cylinder and conducts them overboard. Included are the exhaust headers and collector

More information

CIRRUS AMM TEMPORARY REVISION

CIRRUS AMM TEMPORARY REVISION CIRRUS AMM TEMPORARY REVISION MODEL SF50 SF50 AMM Temporary Revision --01 Brakes Affected Manuals: SF50 Airplane Maintenance Manual (18-001, Revision 1) Serial Numbers: SF50 Serials 0005 & subs Filing

More information

SPECIAL PURPOSE EQUIPMENT

SPECIAL PURPOSE EQUIPMENT All SPECIAL PURPOSE EQUIPMENT 1. GENERAL This section describes special purpose equipment on the airplane. This equipment includes the Cirrus Airplane Parachute System (CAPS) the aft tiedown ballast bracket,

More information

SAMPLE BLUE STAR CONVERSION INSTALLATION OF CONTINENTAL IO-470-N BEECH MODEL J35, K35, M35 LWS C-470-N. REVISION 2. September 16, 1992 STC SA5635SW

SAMPLE BLUE STAR CONVERSION INSTALLATION OF CONTINENTAL IO-470-N BEECH MODEL J35, K35, M35 LWS C-470-N. REVISION 2. September 16, 1992 STC SA5635SW BLUE STAR CONVERSION INSTALLATION OF CONTINENTAL IO-470-N BEECH MODEL J35, K35, M35. REVISION 2 September 16, 1992 STC SA5635SW SAMPLE 1 1992SAMPLE BLUE STAR CONVERSION Table of Contents Page Description

More information

Housing (Front) - Remove

Housing (Front) - Remove SENR9978-01 63 1. Lift the assembly (3) of the idler gear and the hub over the housing for the crankshaft front seal (2) and insert the hub into the recess in the cylinder block. Refer to illustration

More information

HARTZELL PROPELLER INC. ACTIVE SERVICE INSTRUCTION INDEX - February 09, 2018 (excluding HD series propeller and systems)

HARTZELL PROPELLER INC. ACTIVE SERVICE INSTRUCTION INDEX - February 09, 2018 (excluding HD series propeller and systems) 1A 09/23/75 Installation of C-2052, C-2052-1, or C-2052-3 Governor and T Drive Kit on Bonanza. 2 03/01/55 Installation of Tee Drive C-192-2 for hydraulic & vacuum pump. 3 12/01/52 Installation of HC-12X20-8/8428

More information

HARTZELL PROPELLER INC.

HARTZELL PROPELLER INC. HARTZELL PROPELLER INC. One Propeller Place Piqua, Ohio 45356-2634 U.S.A. Telephone: 937.778.4200 Fax: 937.778.4391 MANUAL REVISION TRANSMITTAL Manual (61-00-39) Propeller Owner's Manual and Logbook REVISION

More information

DOA No. E HAWKER A200CT. NOTE: aircraft maintenance. Published EASA.21J.020

DOA No. E HAWKER A200CT. NOTE: aircraft maintenance. Published EASA.21J.020 EASA STC No. 00369 96 INSTALLATION INSTRUCTIONS E-20422 MT-PROPELLER MODEL MTV-27--E-C-F-R(P)/CFR22-f ON HAWKER BEECHCRAFT CORPORATION 200, 200C, 200CT, 200T, A200 (C-2A, C-2C), A200CT (C-2D, FWC-2D, RC-2D),

More information

Service Bulletin. ATA 27-00: Flight Controls Rudder-Aileron Interconnect Modification

Service Bulletin. ATA 27-00: Flight Controls Rudder-Aileron Interconnect Modification Service Bulletin Issued: 09 May 2007 Models SR20 and SR22 ATA 27-00: Flight Controls Rudder-Aileron Interconnect Modification COMPLIANCE Mandatory: Accomplish this Service Bulletin within 25 Flight Hours

More information

WHIRLWIND. Owner s Manual 200RV Series (Rev ) Model: 200RV Serial Number: 200RV- Manufacture Date: A V I A T I O N WHIRL WIND AVIATION

WHIRLWIND. Owner s Manual 200RV Series (Rev ) Model: 200RV Serial Number: 200RV- Manufacture Date: A V I A T I O N WHIRL WIND AVIATION WHIRLWIND A V I A T I O N M a nufacturer of Composite Constant Speed P r o pellers Model: 200RV Serial Number: 200RV- Manufacture Date: Owner s Manual 200RV Series (Rev 2014-2) WHIRL WIND AVIATION 1419

More information

WHIRLWIND. Owner s Manual 200G-CS & 210 (Rev ) Model: Serial Number: Manufacture Date: A V I A T I O N WHIRL WIND AVIATION

WHIRLWIND. Owner s Manual 200G-CS & 210 (Rev ) Model: Serial Number: Manufacture Date: A V I A T I O N WHIRL WIND AVIATION WHIRLWIND A V I A T I O N M a nufacturer of Composite Constant Speed P r o pellers Model: Serial Number: Manufacture Date: Owner s Manual 200G-CS & 210 (Rev 2014-2) WHIRL WIND AVIATION 1419 STATE ROUTE

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL SYSTEM 55 AUTOPILOT 1. DESCRIPTION The S-TEC System 55 is a dual axis autopilot system that provides roll stability, heading hold, NAV/GPS tracking, altitude hold, vertical speed selection, automatic glideslope

More information

WHEELS 1. DESCRIPTION A.

WHEELS 1. DESCRIPTION A. WHEELS 1. DESCRIPTION A. Main Wheels Serials 22-0002 thru 22-4045 before SB2X-32-21, 22T-0001 thru 22T-0689 before SB2X-32-21: The main wheels are of aluminum construction and designed to be used with

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL STALL WARNING SYSTEM 1. DESCRIPTION A. Stall Warning System - Serials 05 thru 2015, 2016 & subs w/o Perspective Avionics The airplane uses an electro-pneumatic stall warning system. As the angle of attack

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL MODEL SR PASSENGER AND CREW DOORS. DESCRIPTION AND OPERATION Serials 000 thru 00: The two crew/passenger doors incorporate a flush-mount outside door handle, key-operated door lock, and a conventional

More information

NEUFORM 3-Blade-Variable Pitch Propeller R2 Series. Assembly and Maintenance Manual

NEUFORM 3-Blade-Variable Pitch Propeller R2 Series. Assembly and Maintenance Manual NEUFORM 3-Blade-Variable Pitch Propeller R2 Series for Rotax 912, 912S and 914 Manual control by hand lever (H) or electric constant speed control (ECS) Date: 28 April 2010 Your NEUFORM-Distributor: Table

More information

SERVICE MANUAL for. Engine-to-Generator. Part Number used on. John Deere Engine Driven Aircraft Ground Power Single-Bearing Generator Sets

SERVICE MANUAL for. Engine-to-Generator. Part Number used on. John Deere Engine Driven Aircraft Ground Power Single-Bearing Generator Sets TO-216 SERVICE MANUAL for Engine-to-Generator FLEXIBLE COUPLING Part Number 181267 used on John Deere Engine Driven Aircraft Ground Power Single-Bearing Generator Sets manufactured by HOBART BROTHERS COMPANY

More information

SD3-60 AIRCRAFT MAINTENANCE MANUAL ASSEMBLY (FIVE-BLADED PROPELLERS) - MAINTENANCE PRACTICES

SD3-60 AIRCRAFT MAINTENANCE MANUAL ASSEMBLY (FIVE-BLADED PROPELLERS) - MAINTENANCE PRACTICES AMM 1.0.0.0PROPELLER ASSEMBLY (FIVE-BLADED PROPELLERS) - MAINTENANCE PRACTICES NOTE: For six-bladed propeller assemblies (aircraft equipped with PT6A-67R engines), refer as follows: 1. Servicing Model

More information

18SP680Rev3 EPA04 MBE 4000 Car Hauler Low Pressure Fuel Lines

18SP680Rev3 EPA04 MBE 4000 Car Hauler Low Pressure Fuel Lines 8SP680Rev3 EPA04 MBE 4000 Car Hauler Low Pressure Fuel Lines KIT DESCRIPTION These service kits include all necessary parts to replace the low pressure fuel lines between the fuel filter housing and fuel

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL VISION SF50 CHAPTER 32-42: BRAKES GENERAL. Brakes 32-42: BRAKES. 1. General

CIRRUS AIRPLANE MAINTENANCE MANUAL VISION SF50 CHAPTER 32-42: BRAKES GENERAL. Brakes 32-42: BRAKES. 1. General Brakes GENERAL 32-2: BRAKES 1. General This chapter describes that portion of the system which provides for stopping the aircraft while on the ground and taxiing/directional control of the aircraft. Includes

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL ANALYZERS - ENGINE MONITORING. DESCRIPTION This section describes that portion of the engine indicating system which is used to analyze engine performance, temperature, and condition. Serials 00 thru 8

More information

Passenger And Crew Door

Passenger And Crew Door CIRRUS AIRPLANE MAINTENANCE MANUAL Passenger And Crew Door CHAPTER 5-10: PASSENGER AND CREW DOOR GENERAL 5-10: PASSENGER AND CREW DOOR 1. General The two crew/passenger doors incorporate a flush-mount

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL BRAKES. DESCRIPTION The brake system consists of single disc brake assembly on each main landing gear wheel, master cylinder for each rudder pedal, hydraulic fluid reservoir, parking brake, and associated

More information

Accident Prevention Program

Accident Prevention Program Accident Prevention Program Maintenance Aspects of Owning Your Own Airplane Introduction As an owner-pilot, FAR Part 43 allows you to perform certain types of inspections and maintenance on your airplane.

More information

1. Previous testing found a large oil leak from the front of the engine when running at high power.

1. Previous testing found a large oil leak from the front of the engine when running at high power. Bearhawk #164 Three Sigma Checkout Report Date: 23-27 Apr 08 Objectives: 1. Find and address the source of the engine oil leak 2. Adjust propeller governor high RPM stop 3. Adjust carburetor idle mixture

More information

PROPELLERS - PROPELLER SLIP RING MOUNTING PLATE INSPECTION AND REPAIR

PROPELLERS - PROPELLER SLIP RING MOUNTING PLATE INSPECTION AND REPAIR Beechcraft TITLE: PROPELLERS - PROPELLER SLIP RING MOUNTING PLATE INSPECTION AND REPAIR 1. Planning Information A. Effectivity (1) Airplanes Airplanes that have accomplished installation of Hartzell STC

More information

CHAPTER 65 TAIL ROTOR DRIVE SYSTEM. Section Title Page

CHAPTER 65 TAIL ROTOR DRIVE SYSTEM. Section Title Page CHAPTER 65 TAIL ROTOR DRIVE SYSTEM Section Title Page 65-00 Description........................................ 65.1 65-10 Tail Rotor Drive Fan Shaft.............................. 65.1 65-20 Tail Rotor

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL SPECIAL PURPOSE EQUIPMENT 1. GENERAL This section describes special purpose equipment on the airplane. This equipment includes the Cirrus Airplane Parachute System (CAPS) and the aft tiedown ballast bracket.

More information

WHIRL WIND PROPELLERS Ground Adjustable (GA) Aircraft Propeller Installation & Maintenance Instructions. Propeller Model: GA-UL350.

WHIRL WIND PROPELLERS Ground Adjustable (GA) Aircraft Propeller Installation & Maintenance Instructions. Propeller Model: GA-UL350. WHIRL WIND PROPELLERS Ground Adjustable (GA) Aircraft Propeller Installation & Maintenance Instructions Propeller Model: GA-UL350 Engine: UL350 WHIRLWIND PROPELLERS CORPORATION 1800-C Joe Crosson Drive

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL FLIGHT SURFACES. DESCRIPTION The flaps are mounted to the trailing edge of each wing between the inboard end of the ailerons and the fuselage. The ailerons are located near the wing tips and hinge to the

More information

DISASSEMBLY. Engine. Special Tool(s) Locking Tool, Camshaft Phaser Sprocket Special Tool(s)

DISASSEMBLY. Engine. Special Tool(s) Locking Tool, Camshaft Phaser Sprocket Special Tool(s) 303-01B-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Rear Slinger 303-514 (T95P-6701-AH) Special Tool(s) 303-01B-1 Locking Tool, Camshaft Phaser Sprocket 303-1046 Remover, Crankshaft Rear Seal

More information

OPERATOR'S MANUAL NO, 136 TRW HARTZELL REVERSIBLE PROPELLER PRESSURE CONTROL UNIT ( )

OPERATOR'S MANUAL NO, 136 TRW HARTZELL REVERSIBLE PROPELLER PRESSURE CONTROL UNIT ( ) OPERATOR'S MANUAL NO, 136 TRW HARTZELL REVERSIBLE PROPELLER ( 1HC-H )Y( k7 PRESSURE CONTROL UNIT 3-4270-( ) JUNE 21, 1982 1. OPERATION 2. INSTALLATION INSTRUCTIONS 3. INSTALLATION OF PRESSURE CONTROL UNIT

More information

SCHEDULED MAINTENANCE

SCHEDULED MAINTENANCE SCHEDULED MAINTENANCE 1. DESCRIPTION These inspections meet the intent of 14 CFR 91.409 and Part 43, Appendix D. In addition to the inspections prescribed by this schedule, the altimeter instrument and

More information

57-20 AUXILIARY STRUCTURE

57-20 AUXILIARY STRUCTURE AUXILIARY STRUCTURE 1. DESCRIPTION The leading edge of the wing is manufactured from composite materials. This airplane has a one-piece wing with individual wing tips. The wing tips are manufactured from

More information

Installation of C-2052, C , C or C Governor and "T" Drive Kit on Bonanza

Installation of C-2052, C , C or C Governor and T Drive Kit on Bonanza INSTRUCTIONS NO. 1A Installation of C-2052, C-2052-1, C-2052-2 or C-2052-3 Governor and "T" Drive Kit on Bonanza These instructions are provided for the installation of Hartzell "T" drive on Continental

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL OVERHAUL AND REPLACEMENT SCHEDULE 1. DESCRIPTION The following items must be overhauled or replaced at the following intervals unless otherwise noted. To ensure correct observation of these times, the

More information

SD3-60 AIRCRAFT MAINTENANCE MANUAL ASSEMBLY - MAINTENANCE PRACTICES (SIX-BLADED PROPELLERS, MODEL HC-A6A-3A, POST HARTZELL SERV. BULL.

SD3-60 AIRCRAFT MAINTENANCE MANUAL ASSEMBLY - MAINTENANCE PRACTICES (SIX-BLADED PROPELLERS, MODEL HC-A6A-3A, POST HARTZELL SERV. BULL. SD3-60 AIRCRAFT MAINTENANCE MANUAL z AMM 3.0.0.0PROPELLER ASSEMBLY - MAINTENANCE PRACTICES (SIX-BLADED PROPELLERS, MODEL HC-A6A-3A, POST HARTZELL SERV. BULL. 168) NOTE: Five-bladed propeller assemblies

More information

X-Trainer 43mm fork service manual. Beta USA, Inc This work should be performed by a trained motorcycle technician.

X-Trainer 43mm fork service manual. Beta USA, Inc This work should be performed by a trained motorcycle technician. X-Trainer 43mm fork service manual Beta USA, Inc. 2016 This work should be performed by a trained motorcycle technician. Table of contents Page Introduction/special tools... 2 Fork exploded view... 3 Legend.

More information

1996 Aerostar/Ranger/Explorer

1996 Aerostar/Ranger/Explorer Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding

More information

57-50 FLIGHT SURFACES

57-50 FLIGHT SURFACES FLIGHT SURFACES 1. DESCRIPTION The flaps are mounted to the trailing edge of each wing between the inboard end of the ailerons and the fuselage. The ailerons are located near the wing tips and hinge to

More information

Installation Guide Current Ford F-250 & Ford F-350 Super Duty. Product Code: 109 & 119

Installation Guide Current Ford F-250 & Ford F-350 Super Duty. Product Code: 109 & 119 Installation Guide 2008 - Current Ford F-250 & Ford F-350 Super Duty Product Code: 109 & 119 September 1, 2012 Tools Needed Components Included 3/8" Drill P2 Tip #2 Philips Screwdriver 1/2" Drill Bit Hinged

More information

DC Generation. 1. General. A. DC Generation

DC Generation. 1. General. A. DC Generation CIRRUS AIRPLANE MAINTENANCE MANUAL DC Generation CHAPTER -0: DC GENERATION GENERAL -0: DC GENERATION 1. General (See Figure -0-1) This section covers the systems to generate, regulate, control, and indicate

More information

1994 Mazda MX-5 Miata. CLUTCH 1994 Clutch

1994 Mazda MX-5 Miata. CLUTCH 1994 Clutch CLUTCH 1994 Clutch DESCRIPTION Miata uses a hydraulically operated clutch. HYDRAULIC SYSTEM BLEEDING 1. Remove bleeder screw cap, located at clutch release cylinder. Install vinyl hose onto bleeder screw.

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL AUXILIARY STRUCTURE 1. DESCRIPTION The leading edge of the wing is manufactured from composite materials. This airplane has a one-piece wing with individual wing tips. The wing tips are manufactured from

More information

Brake System H TX, H2.0TXS [B475]; H TX [B466] Safety Precautions Maintenance and Repair

Brake System H TX, H2.0TXS [B475]; H TX [B466] Safety Precautions Maintenance and Repair HMM180001 Brake System H1.5-1.8TX, H2.0TXS [B475]; H2.5-3.5TX [B466] Safety Precautions Maintenance and Repair When lifting parts or assemblies, make sure all slings, chains, or cables are correctly fastened,

More information

Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)

Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR) SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,

More information

O-540-F1B5 SERIES PARTS CATALOG WIDE CYLINDER FLANGE CRANKCASE MODEL ENGINES

O-540-F1B5 SERIES PARTS CATALOG WIDE CYLINDER FLANGE CRANKCASE MODEL ENGINES INTRODUCTION This illustrated parts catalog contains a complete parts listing for the Lycoming O-540-F1B5 series wide cylinder flange crankcase model aircraft engines. Major assembly and sub-assembly parts

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL STORAGE 1. DESCRIPTION A. Fuel Storage System - Serials 1005 thru 1885 The fuel storage system consists primarily of a vented integral 30.3-gallon (114.5-liters) capacity fuel tank in each wing, a fuel

More information

C I R R U S BRAKES DESCRIPTION

C I R R U S BRAKES DESCRIPTION BRAKES. DESCRIPTION The brake system consists of a single disc brake assembly on each main landing gear wheel, master cylinder for each rudder pedal, hydraulic fluid reservoir, parking brake, and associated

More information

Storage. 1. General. A. Fuel Storage System

Storage. 1. General. A. Fuel Storage System CIRRUS AIRPLANE MAINTENANCE MANUAL Storage CHAPTER 28-10: STORAGE GENERAL 28-10: STORAGE 1. General A. Fuel Storage System The fuel storage system consists primarily of a vented integral 47.5-gallon (180-liters)

More information

LANCAIR LEGACY PRE-TEST FLIGHT INSPECTION (8-04)

LANCAIR LEGACY PRE-TEST FLIGHT INSPECTION (8-04) LANCAIR LEGACY PRE-TEST FLIGHT INSPECTION (8-04) OWNER PHONE # ADDRESS N SERIAL # AIRCRAFT TYPE DATE / / TACH TIME hrs. TOTAL TIME hrs. EMPTY WEIGHT CG. PAINT & INTERIOR? YES NO ENGINE TYPE PROPELLER ALL

More information

D'Shannon Products, Ltd County Road 134 Buffalo, MN Supplemental Type Certificate SA2200SW. Installation Instructions

D'Shannon Products, Ltd County Road 134 Buffalo, MN Supplemental Type Certificate SA2200SW. Installation Instructions 1992 D'Shannon Products, Ltd. Supplemental Type Certificate SA2200SW Installation Instructions Teledyne Continental IO-520-B, -BA, -BB and IO-550-B Engines Series II Beechcraft 35 and 33 Airplanes Eligible

More information

Page 1 of HP B&S Vanguard Engine

Page 1 of HP B&S Vanguard Engine 1405 Page 1 of 41 14 HP B&S Vanguard Engine 1405 Page 2 of 41 14 HP B&S Vanguard Engine Ref # Part Number Qty S/P/F Description BS-28Q777-0647-E1 1 14 HP B&S Vanguard Engine 1 BS-496412 1 Cylinder Assembly

More information

C I R R U S BRAKES DESCRIPTION

C I R R U S BRAKES DESCRIPTION BRAKES. DESCRIPTION The brake system consists of a single disc brake assembly on each main landing gear wheel, master cylinder for each rudder pedal, hydraulic fluid reservoir, parking brake, and associated

More information

SAMPLE BLUE STAR CONVERSION INSTALLATION OF CONTINENTAL IO-470-C OR IO-470-N BEECH MODELS THROUGH F-33 LWS STC # SA5527SW REVISION 5

SAMPLE BLUE STAR CONVERSION INSTALLATION OF CONTINENTAL IO-470-C OR IO-470-N BEECH MODELS THROUGH F-33 LWS STC # SA5527SW REVISION 5 BLUE STAR CONVERSION INSTALLATION OF CONTINENTAL IO-470-C OR IO-470-N BEECH MODELS 35-33 THROUGH F-33 LWS 470-33 STC # SA5527SW REVISION 5 FEBRUARY 5, 1996 BLUE STAR CONVERSION TABLE OF CONTENTS PAGE DESCRIPTION

More information

1 search parameters. 75 results. Exact Match. Model. Engine Fuel & Control - Installation of Improved Carburetor Airboxes

1 search parameters. 75 results. Exact Match. Model. Engine Fuel & Control - Installation of Improved Carburetor Airboxes 1 search parameters 08.17.04 Category Model Value 76 Duchess ME-Serials> Occurance Exact Match 75 results 1055 Engine Fuel & Control - Installation of Improved Carburetor Airboxes 1051 5 2 Doors - Replace

More information

Service Bulletin. ATA 52-10: Passenger and Crew Doors Door Latching Assembly Upgrade

Service Bulletin. ATA 52-10: Passenger and Crew Doors Door Latching Assembly Upgrade Service Bulletin Issued: 5 Oct 00 Models SR0 and SR ATA 5-10: Passenger and Crew Doors Door Latching Assembly Upgrade COMPLIANCE Optional: Accomplishment of this Service Bulletin is at the owner s option.

More information

Maintenance Instruction 23.1

Maintenance Instruction 23.1 Subject: Replacement of engine GROB 2500 E1/D1 by engine LIMBACH L 2400 EB1.AA Affected Aircraft: Motor glider GROB G 109 (B) Aircraft: Type G 109 (B) Registration Propeller: Type MTV-1-A/L160-03 Serial

More information

Storage. 1. General. A. Fuel Storage System

Storage. 1. General. A. Fuel Storage System Storage GENERAL 28-10: STORAGE 1. General A. Fuel Storage System The fuel storage system consists primarily of a vented integral 149.25-gallon (1009-liter) capacity main fuel tank in each wing, an integral

More information

Page 1 of 21 303-01C Engine 5.4L (3V) 2009 F-150 REMOVAL Procedure revision date: 03/26/2009 Cylinder Head Special Tool(s) 3 Jaw Puller 303-D121 or equivalent Compressor, Valve Spring 303-1039 Holding

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING DIAGNOSIS AND TESTING SUSPENSION AND STEERING SYSTEM 2007 SUSPENSION Suspension - Nitro CONDITION POSSIBLE CAUSES CORRECTION FRONT END NOISE 1. Loose or worn wheel bearings. 1. Replace wheel bearings.

More information

MANDATORY SERVICE BULLETIN The Subject Matter of this Service Bulletin is Incorporated In Whole or in Part in an FAA Airworthiness Directive

MANDATORY SERVICE BULLETIN The Subject Matter of this Service Bulletin is Incorporated In Whole or in Part in an FAA Airworthiness Directive TELEDYNE CONTINENTAL AIRCRAFT ENGINE MANDATORY SERVICE BULLETIN The Subject Matter of this Service Bulletin is Incorporated In Whole or in Part in an FAA Airworthiness Directive SUBJECT: MAGNETO TO ENGINE

More information

SECTION C Engine 6.0L Diesel

SECTION C Engine 6.0L Diesel 303-01C-i Engine 6.0L Diesel 303-01C-i SECTION 303-01C Engine 6.0L Diesel CONTENTS PAGE IN-VEHICLE REPAIR Cylinder Head RH... 303-01C-2 303-01C-2 Engine 6.0L Diesel 303-01C-2 IN-VEHICLE REPAIR Cylinder

More information

Illustrated Parts Manual. 700 Diesel

Illustrated Parts Manual. 700 Diesel ATV Illustrated Parts Manual A R C T I C C A T 700 Diesel Model Number A2007TBT4DUSR (Red) Model Number A2007TBT4DUSG (Green) Model Number A2007TBT4DOSG (Green - International) MORE TO GO ON. TABLE OF

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL SCHEDULED MAINTENANCE 1. DESCRIPTION These inspections meet the intent of 14 CFR 91.409 and Part 43, Appendix D. In addition to the inspections prescribed by this schedule, the altimeter instrument and

More information

Parts List Single Reduction Models, Cast Iron Units

Parts List Single Reduction Models, Cast Iron Units Parts List Single Reduction Models, Cast Iron Units 60 51 51 10 24 11 11 9 24 12 19 17 27 31 8 23 7 14 20 28 26 5 1 2 6 44 60 50 23 7 6 30 27 30 4 3 30 13 29 14 22 18 27 43 48 50 8 15 16 12 25 9 51 51

More information

TYPE CERTIFICATE DATA SHEET

TYPE CERTIFICATE DATA SHEET TYPE CERTIFICATE DATA SHEET No. IM.P.137 for Propeller 3C1 ( ) series propellers Type Certificate Holder One Propeller Place Piqua, OH 45356 2634 USA For Model: 3C1 R919A1 3C1 L675A1 TE.CERT.00050 001

More information