INSTALLATION GUIDE. Directed Digital Solutions GM11. Designed by Installers for Installers

Size: px
Start display at page:

Download "INSTALLATION GUIDE. Directed Digital Solutions GM11. Designed by Installers for Installers"

Transcription

1 INSTALLATION GUIDE Directed Digital Solutions GM Designed by Installers for Installers 208 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle s electrical system and components

2 Contents Warning! Safety first... 3 Introduction... 4 Pre-installation and application warnings... 4 Vehicle application guide... 5 Wiring connections... 6 Main power harness (H), 2-pin thick gauge... 6 Auxiliary output harness (H2), 6-pin black... 6 Analog harness (H3), 8-pin white... 7 MC50 harness (H4), 8 thick-gauge wires (optional)... 7 Installation (wiring diagrams & vehicle wiring reference charts)... 8 Type with T-Harness (THGMC2)... 8 Type... 9 Type 2 with T-Harness (THGMC2)... 5 Type Type Type Type Connecting the module Important! Manual or automatic transmission selection Optional sensors RF Systems When used in conjunction with SmartStart Module programming LED diagnostics and troubleshooting... 3 Soft reset Hard reset Learning the Tach (not needed with Virtual Tach) Initializing Virtual Tach (not needed with hardwired or data tach applications) Limited lifetime consumer warranty Quick Reference Guide... 36

3 Warning! Safety first The following safety warnings must be observed at all times: Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation. The following precautions are the sole responsibility of the user; however, authorized Directed dealers should: Never use a test light or logic probe when installing this unit. Always use a multimeter. Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage). When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed toggle switch. It is the user s sole responsibility to properly handle and keep out of reach from children all remote controls to assure that the system does not unintentionally remote start the vehicle. USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES. Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. Except when performing the Safety Check outlined in this installation guide, () Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately. OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS. Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged parking brake. Do not allow anyone to stand in front of or behind the vehicle. This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such vehicles may pose certain risk. 3 Directed Digital Solutions GM

4 Introduction The GM firmware for Directed Digital Solutions is compatible with specific Buick, Cadillac, Chevrolet, GMC, Hummer, Pontiac, Saturn, and Suzuki vehicles. It is a complete solution for remote start, security (if applicable), bypass interface, and convenience. This guide provides information on the installation of the module using GM. If you would prefer using this system as a digital solution, go to and search for the make, model and year of the vehicle. This will allow you to find the proper firmware and corresponding installation guide. Warning! This module can only be programmed via the web tool, which can be found on or using the Directechs Mobile application for mobile devices. Features and functions will become accessible when you connect the module using the XKLoader. Pre-installation and application warnings Firmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle limitations. T-Harness compatible THGMC2 Keys required for programming Keys required for operation 0 The optional Plug & Play THGMC2 T-Harness is sold separately. The Cadillac SRX, Chevrolet Captiva Sport, Chevrolet Equinox, 208 Chevrolet Express Van, 208 GMC Savana, Pontiac Torrent, Saturn VUE and Suzuki XL7 are NOT compatible with optional T-Harness THGMC2. The Cadillac CTS, Chevrolet Impala/Impala Limited and Buick Lucerne require the trunk feature to be set to Electric Rear Hatch option for the trunk to work. The OBDII Diagnostic Connector features will remain the same even when the T-Harness is installed. Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic Refer to the "Vehicle wiring reference chart" following each installation type. General notes: This section highlights important information for this specific firmware. [] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin. [2] The siren is ONLY required when enabling the security features during module flashing. Additional parts required (maximum required): 87 Diode 6A 0 x A Diodes 87a x Relay esistor 00 0 x Resistor Fuse 7.5A 0 x Fuse 4 Directed Digital Solutions GM

5 Vehicle application guide The table below lists the vehicles and features which are compatible with this product. Refer to the following pages for more information on installation wiring, programming and troubleshooting for these vehicles. Vehicles PK-Immobilizer Bypass-Data No Key Req'd CC-Heated Seats Activation DL-Arm Factory Security DL-Disarm Factory Security Buick Enclave Lucerne Cadillac CTS CTS Coupe CTS Wagon DTS Escalade SRX Chevrolet Avalanche Caprice Captiva Sport Equinox Express Van Impala Impala Limited Monte Carlo Silverado Silverado 2500/ Suburban Tahoe Traverse GMC Acadia Savana Sierra Sierra 2500/ Yukon Hummer H Pontiac G8 Torrent Saturn Outlook VUE (4-Cylinder) VUE (V6) Suzuki XL Legend: CC: Comfort & Convenience Controls DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w/ FOB Remote PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock DL-Trunk / Hatch Release FOB-Control of aftermarket alarm with OEM remote RS-3x LOCK START (Start control using OEM Remote) RS-3x LOCK STOP (Stop control using OEM Remote) RS-RAP Shut Down (Retained ACC Power) RS-Remote Start Takeover RS-SmartStart RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin SS-Factory Alarm Trigger Monitoring ST-Brake Status (foot brake) ST-Door Locks Status ST-Ignition Status 5 Directed Digital Solutions GM

6 Wiring connections The wiring connections listed below are specific to this firmware. Main power harness (H), 2-pin thick gauge connector Conn./Pin Color Description H/ White Relay 3 COM Parking Light Output H/2 White/Brown Relay 3 N.O. Parking Light Input H/3 Brown/Red Relay 2 N.O. No Connection H/4 Yellow/Red Relay 2 COM Immobilizer Interrupt (conn. side) H/5 Orange/Red Relay 2 N.C. Immobilizer Interrupt (vehicle side) H/6 Yellow Relay COM (+) Ignition Output H/7 White Relay 3 COM Parking Light Output H/8 White/Brown Relay 3 N.O. Parking Light Input H/9 Black (-) Ground H/0 Red (+) 2V Input H/ Orange/Yellow Relay N.C. No Connection H/2 Brown Relay N.O. (+) 2 V Input Auxiliary output harness (H2), 6-pin black connector Conn./Pin Color Description H2/ Violet/Brown No Connection H2/2 Yellow/Black Clock H2/3 Orange/Black Data H2/4 Tan HS CAN Low H2/5 Tan/Black HS CAN High H2/6 Light Green Single Wire CAN H2/7 Orange/Green No Connection H2/8 Orange/Brown No Connection H2/9 Violet/Green No Connection H2/0 Green/Black (-) Parking Lights Output 2 H2/ White/Violet No Connection 2 H2/2 White/Red (+) Accessory Output 2 H2/3 Lt. Blue/Black (-) RAP Off Output 2 H2/4 Green/Red No Connection 2 H2/5 N/A No Connection H2/6 Violet/Yellow No Connection. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. 2. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. 6 Directed Digital Solutions GM

7 Analog harness (H3), 8-pin white connector Conn./Pin Color Description H3/ Lt. Blue/Red No Connection H3/2 Black/White (-) Parking Brake Input (manual transmission) 2 H3/3 Gray (-) Hood Input 2 H3/4 N/A No Connection H3/5 Gray/Black (+) Glow Plug Input 2 H3/6 Violet/White (AC) Tach Input 2 H3/7 Dark Blue No Connection H3/8 Brown/Black (-) Horn H3/9 Red/White No Connection H3/0 White/Green (-) Door Input 2 H3/ Yellow/Green (+) Door Input 2 H3/2 Blue/Red No Connection H3/3 Light Blue (-) Trunk Trigger Input 2 H3/4 Pink/Yellow (-) Activation (start) Input H3/5 Dark Green No Connection H3/6 Brown/White (+) Brake Input 2 H3/7 Brown (+) Siren Output H3/8 Blue/White (-) Ground When Running (status) Output MC50 harness (H4), 8 thick-gauge wires (optional) Conn./Pin Color Description H4/ Pink/White (+) Ignition 2/Flex Relay Output 3 H4/2 Red/White (+) Fused (30A) Ignition 2/Flex Relay Input H4/3 Pink (+) Ignition Output (also input to Yellow in ribbon cable) H4/4 Red (+) 2 Volt (battery) Input H4/5 Orange (+) Accessory Output H4/6 Red (+) 2 Volt (battery) Input H4/7 Green Starter Input (from key switch) 4 H4/8 Violet (+) Starter Output (to starter). If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. 2. These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle application guide" on page 5 for a list of compatible features. 7 Directed Digital Solutions GM

8 Installation (wiring diagrams & vehicle wiring reference charts) Type with T-Harness (THGMC2) Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ). TYPE HS CAN High: Tan/Black or Tan/White, pin 6 Immobilizer Control Module (under ignition switch) Single Wire CAN: Dk. Green, pin HS CAN Low: Tan, pin 4 OBDll Plug Black Connector Ignition Barrel TYPE 2 NOT USED HS CAN Low: Tan Single Wire CAN: Lt. Green HS CAN High: Tan/Black 6-Pin Black Connector THGMC2 (Optional T-Harness) Remote Start Safety Override Ignition Switch Drivers Window Switch (in drivers door) 8 (-) RAP Off Output: Lt. Blue/Black (-) Parking Lights Output: Lt. Green/Black 6 2 The Remote Start Safety Override Switch MUST be in the ON position (-) Driver Door Trigger: Gray/Black: pin 3 OR Hood Pin (-) Hood Input: Gray: 3 (-) Driver Door Trigger: Gray/Black: pin 0 BCM X6 connector BCM - X2 connector Siren (-) Parking Lights: Pin 8 (+) Siren Output: Brown: 7 2-Pin White Connector BCM X7 X6 X5 X4 X3 X2 X 8 Directed Digital Solutions GM

9 Type Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ). BCM - X2 connector (-) Parking Lights: Pin 8 HS CAN High: Tan/Black or Tan/White, pin 6 Single Wire CAN: Dk. Green, pin 8 OBDII Plug Black Connector 9 6 HS CAN Low: Tan, pin 4 HS CAN Low: Tan: 4 X7 X6 X5 X4 X3 X2 X BCM BCM - X4 connector 25 9 HS CAN High: Tan/Black: 5 Single Wire CAN: Lt. Green: BCM - X6 connector (-) Parking Lights Output: Green/Black: 0 (+) Accessory Output: White/Red: 2 (-) RAP Off Output: Lt. Blue/Black: 3 Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. (+) 2V: Pin (-) Drivers Door Trigger: Gray/Black, pin 0 Hood Pin (-) Hood Input: Gray: 3 2: Brown: (+) 2V Input 0: Red: (+) 2V Input 9: Black: (-) Ground Drivers Window Switch (in drivers door) OR (-) Drivers Door Trigger: Gray/Black, pin 3 Siren (+) Siren Output: Brown: 7 6: Yellow: (+) Ignition Output Ignition Barrel 5: Orange/Red: Immobilizer Interrupt (vehicle side) 4: Yellow/Red: Immobilizer Interrupt (conn. side) (+) Immobilizer Power: Pin CUT Immobilizer Control Module (under ignition switch) Ignition Switch Connector (black conn.) (+) Accessory: Brown, pin 3 (+) Ignition: Pink, pin 9 Directed Digital Solutions GM

10 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Buick Enclave Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM left of steering column, X4 Black 25 D Parking Lights Brown/White 8 (-) BCM left of steering column, X2 White 25 D "OUT " Buick Lucerne Gray/Black 0 (-) BCM left of steering column, X6 Pink 25 D Gray/Black 3 (-) Drivers window switch. Brown 6 E Immobilizer Interrupt Orange (+) Immobilizer control module. Black 5 A Ignition Pink (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/Yellow (+) BCM above passenger kick, X4 Black 25 F Parking Lights Lt. Blue/Tan 8 (-) BCM above passenger kick, X2 White 25 F Driver Door Trigger Gray/Black 3 (-) Drivers window switch. Brown 6 E 0 Directed Digital Solutions GM

11 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Cadillac CTS Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM above gas pedal, X4 Black 25 G Parking Lights Brown/White 8 (-) BCM above gas pedal, X2 White 25 G Driver Door Trigger Gray/Black 3 (-) Drivers window switch. Brown 6 E Cadillac CTS Coupe Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM above gas pedal, X4 Black 25 G Parking Lights Brown/White 8 (-) BCM above gas pedal, X2 White 25 G Driver Door Trigger Gray/Black 3 (-) Drivers window switch. Brown 6 E Cadillac CTS Wagon Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM above gas pedal, X4 Black 25 G Parking Lights Brown/White 8 (-) BCM above gas pedal, X2 White 25 G Driver Door Trigger Gray/Black 3 (-) Drivers window switch. Brown 6 E Cadillac DTS Immobilizer Interrupt Orange/Pink (+) Immobilizer control module. Black 5 A Ignition Pink (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/Yellow (+) BCM above passenger kick, X4 Black 25 F Parking Lights Lt. Blue 8 (-) BCM above passenger kick, X2 White 25 F Driver Door Trigger Gray/Black 3 (-) Drivers window switch. Brown 6 E Directed Digital Solutions GM

12 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Chevrolet Caprice Immobilizer Interrupt Ornage/Black (+) Immobilizer control module. Black 5 A Ignition Pink (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Orange/Red (+) BCM above gas pedal, X4 Black 25 G Parking Lights Brown/White 8 (-) BCM above gas pedal, X2 White 25 G "OUT " Chevrolet Impala Gray/Black or Brown/ White 0 (-) BCM above gas pedal, X6 Pink 25 G Gray/Black 3 (-) Drivers window switch. Brown 6 E Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM under driver dash, X4 Black 25 D Parking Lights Brown/White 8 (-) BCM under driver dash, X2 White 25 D Driver Door Trigger Gray/Black 0 (-) BCM under driver dash, X6 Pink 25 D Chevrolet Impala Limted Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM under driver dash, X4 Black 25 D Parking Lights Brown/White 8 (-) BCM under driver dash, X2 White 25 D Driver Door Trigger Gray/Black 0 (-) BCM under driver dash, X6 Pink 25 D Chevrolet Monte Carlo Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM under driver dash, X4 Black 25 D Parking Lights Brown/White 8 (-) BCM under driver dash, X2 White 25 D Driver Door Trigger Gray/Black 0 (-) BCM under driver dash, X6 Pink 25 D 2 Directed Digital Solutions GM

13 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Chevrolet Traverse Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM left of steering column, X4 Black 25 D Parking Lights Brown/White 8 (-) BCM left of steering column, X2 White 25 D "OUT " GMC Acadia Gray/Black 0 (-) BCM left of steering column, X6 Pink 25 D Gray/Black 3 (-) Drivers window switch. Brown 6 E Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM left of steering column, X4 Black 25 D Parking Lights Brown/White 8 (-) BCM left of steering column, X2 White 25 D "OUT " Pontiac G Gray/Black 0 (-) BCM left of steering column, X6 Pink 25 D Gray/Black 3 (-) Drivers window switch. Brown 6 E Immobilizer Interrupt Orange/Black (+) Immobilizer control module. Black 5 A Ignition Pink (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Orange/Red (+) BCM under driver dash, X4 Black 25 D Parking Lights Brown/White 8 (-) BCM under driver dash, X2 White 25 D "OUT " Gray/Black 0 (-) BCM under driver dash, X6 Pink 25 D Gray/Black 3 (-) Drivers window switch. Brown 6 E 3 Directed Digital Solutions GM

14 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Saturn Outlook Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) Parking Lights Brown/White 8 (-) "OUT " Gray/Black 0 (-) BCM in center dash below radio, X4 BCM in center dash below radio, X2 BCM in center dash below radio, X6 Black 25 H White 25 H Pink 25 H Gray/Black 3 (-) Drivers window switch. Brown 6 E 4 Directed Digital Solutions GM

15 Type 2 with T-Harness (THGMC2) Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ). TYPE NOT USED HS CAN High: Tan/Black or Tan/White, pin 6 Immobilizer Control Module (under ignition switch) Single Wire CAN: Dk. Green, pin HS CAN Low: Tan, pin 4 OBDll Plug Black Connector Ignition Barrel TYPE 2 HS CAN Low: Tan Single Wire CAN: Lt. Green HS CAN High: Tan/Black 6-Pin Black Connector THGMC2 (Optional T-Harness) Remote Start Safety Override Ignition Switch Drivers Window Switch (in drivers door) 8 (-) RAP Off Output: Lt. Blue/Black (-) Parking Lights Output: Lt. Green/Black 6 2 The Remote Start Safety Override Switch MUST be in the ON position (-) Driver Door Trigger: Gray/Black: pin 3 OR Hood Pin (-) Hood Input: Gray: 3 BCM X6 connector BCM - X2 connector Siren (+) Siren Output: Brown: (-) Driver Door Trigger: Gray/Black: pin (-) Parking Lights: Pin 8 2-Pin White Connector BCM (left of steering column or under passenger side dash) X7 X6 X5 X4 X3 X2 X 5 Directed Digital Solutions GM

16 Type 2 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ). BCM - X2 connector (-) Parking Lights: Pin 8 HS CAN High: Tan/Black or Tan/White, pin 6 Single Wire CAN: Dk.Green, pin 8 OBDII Plug Black Connector 9 6 HS CAN Low: Tan, pin 4 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 Single Wire CAN: Lt. Green: 6 X7 X6 X5 X4 X3 X2 X BCM (left of steering column or under passenger side dash) BCM - X4 connector (+) 2V: Red/White, pin BCM - X6 connector (-) Parking Lights Output: Green/Black: 0 (+) Accessory Output: White/Red: 2 (-) RAP Off Output: Lt. Blue/Black: 3 Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. (-) Drivers Door Trigger: Gray/Black, pin 0 Hood Pin (-) Hood Input: Gray: 3 2: Brown: (+) 2V Input 0: Red: (+) 2V Input 9: Black: (-) Ground Drivers Window Switch (brown conn.) OR (-) Drivers Door Trigger: Gray/Black, pin 3 Siren (+) Siren Output: Brown: 7 6: Yellow: (+) Ignition Output Ignition Barrel Ignition Switch Connector (black conn.) (+) Accessory: Brown or Yellow, pin 3 5: Orange/Red: Immobilizer Interrupt (vehicle side) 4: Yellow/Red: Immobilizer Interrupt (conn. side) (+) Immobilizer Power: Red/White, pin CUT Immobilizer Control Module (under ignition switch) (+) Ignition: Pink, pin 2 6 Directed Digital Solutions GM

17 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Cadillac Escalade Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink 2 (+) Ignition Switch. Green 6 B Accessory Brown 3 (+) Ignition Switch. Green 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM left of steering column, X4 Black 25 D Parking Lights Lt. Blue 8 (-) BCM left of steering column, X2 White 25 D Driver Door Trigger Gray/Black 3 (-) Drivers window switch. Brown 6 E Chevrolet Avalanche Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink 2 (+) Ignition Switch. Green 6 B Accessory Brown 3 (+) Ignition Switch. Green 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM left of steering column, X4 Black 25 D Parking Lights Lt. Blue 8 (-) BCM left of steering column, X2 White 25 D Driver Door Trigger Gray/Black 3 (-) Drivers window switch. Brown 6 E Chevrolet Express Van Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink 2 (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM under passenger dash, X4 Black 25 F Parking Lights Lt. Blue 8 (-) BCM under passenger dash, X2 White 25 F "OUT " Gray/Black 0 (-) BCM under passenger dash, X6 Pink 25 F Gray/Black 3 (-) Drivers window switch. Brown 6 E 7 Directed Digital Solutions GM

18 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Chevrolet Silverado Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink 2 (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM left of steering column, X4 Black 25 D Parking Lights Lt. Blue 8 (-) BCM left of steering column, X2 White 25 D "OUT " Chevrolet Silverado 2500/ Gray/Black 0 (-) BCM left of steering column, X6 Pink 25 D Gray/Black 3 (-) Drivers window switch. Brown 6 E Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink 2 (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM left of steering column, X4 Black 25 D Parking Lights Lt. Blue 8 (-) BCM left of steering column, X2 White 25 D "OUT " Chevrolet Suburban Gray/Black 0 (-) BCM left of steering column, X6 Pink 25 D Gray/Black 3 (-) Drivers window switch. Brown 6 E Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink 2 (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM left of steering column, X4 Black 25 D Parking Lights Lt. Blue 8 (-) BCM left of steering column, X2 White 25 D Driver Door Trigger Gray/Black 3 (-) Drivers window switch. Brown 6 E Chevrolet Tahoe Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink 2 (+) Ignition Switch. Green 6 B Accessory Brown 3 (+) Ignition Switch. Green 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM left of steering column, X4 Black 25 D Parking Lights Lt. Blue 8 (-) BCM left of steering column, X2 White 25 D Driver Door Trigger Gray/Black 3 (-) Drivers window switch. Brown 6 E 8 Directed Digital Solutions GM

19 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. GMC Savana Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink 2 (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM under passenger dash, X4 Black 25 F Parking Lights Lt. Blue 8 (-) BCM under passenger dash, X2 White 25 F "OUT " GMC Sierra Gray/Black 0 (-) BCM under passenger dash, X6 Pink 25 F Gray/Black 3 (-) Drivers window switch. Brown 6 E Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink 2 (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM left of steering column, X4 Black 25 D Parking Lights Lt. Blue 8 (-) BCM left of steering column, X2 White 25 D "OUT " GMC Sierra 2500/ Gray/Black 0 (-) BCM left of steering column, X6 Pink 25 D Gray/Black 3 (-) Drivers window switch. Brown 6 E Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink 2 (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM left of steering column, X4 Black 25 D Parking Lights Lt. Blue 8 (-) BCM left of steering column, X2 White 25 D "OUT " GMC Yukon Gray/Black 0 (-) BCM left of steering column, X6 Pink 25 D Gray/Black 3 (-) Drivers window switch. Brown 6 E Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink 2 (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM left of steering column, X4 Black 25 D Parking Lights Lt. Blue 8 (-) BCM left of steering column, X2 White 25 D Driver Door Trigger Gray/Black 3 (-) Drivers window switch. Brown 6 E 9 Directed Digital Solutions GM

20 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Hummer H Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink 2 (+) Ignition Switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM left of steering column, X4 Black 26 D Parking Lights lt. Blue 8 (-) BCM left of steering column, X2 White 25 D "OUT " Gray/Black 0 (-) BCM, X6 Pink 25 D Gray/Black 3 (-) Drivers window switch. Brown 6 E 20 Directed Digital Solutions GM

21 Type 3 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ). BCM - X2 connector (-) Parking Lights: Brown/White, pin HS CAN High: Tan/Black or Tan/White, pin 6 Single Wire CAN: Dk Green, pin 8 OBDII Plug Black Connector 9 6 HS CAN Low: Tan, pin 4 HS CAN Low: Tan: 4 X7 X6 X5 X4 X3 X2 X BCM (under driver dash) BCM - X4 connector 25 9 HS CAN High: Tan/Black: Single Wire CAN: Lt. Green: 6 Drivers Window Switch (in drivers door) (-) Parking Lights Output: Green/Black: 0 (+) Accessory Output: White/Red: 2 (-) RAP Off Output: Lt. Blue/Black: 3 Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. (+) 2V: Red/White, Pin (-) Drivers Door Trigger: Gray/Black, pin 3 Hood Pin (-) Hood Input: Gray: 3 2: Brown: (+) 2V Input 0: Red: (+) 2V Input 9: Black: (-) Ground (+) Siren Output: Brown: 7 6: Yellow: (+) Ignition Output Siren 5: Orange/Red: Immobilizer Interrupt (vehicle side) 4: Yellow/Red: Immobilizer Interrupt (conn. side) (+) Immobilizer Power: Red/White, pin CUT Ignition Barrel Ignition Switch Connector (black conn.) Ignition Switch Connector (black conn.) (+) Accessory: Brown, pin 4 (+) Ignition: Pink, pin Immobilizer Control Module (under ignition switch) 2 Directed Digital Solutions GM

22 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Cadillac SRX Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink 2 (+) Ignition Switch. Green 6 B Accessory Brown 4 (+) Ignition Switch. Green 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM under driver dash, X4 Black 25 D Parking Lights Brown/White 8 (-) BCM under driver dash, X2 White 25 D Driver Door Trigger Gray/Black 3 (-) Drivers window switch. Brown 6 E 22 Directed Digital Solutions GM

23 Type 4 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ). BCM - X2 connector (-) Parking Lights: Lt.Blue, pin 8 HS CAN High: Tan/Black or Tan/White, pin 6 Single Wire CAN: Dk.Green, pin 8 OBDII Plug Black Connector 9 6 HS CAN Low: Tan, pin 4 HS CAN Low: Tan: 4 X7 X6 X5 X4 X3 X2 X BCM (in center console below radio) BCM - X4 connector 25 9 HS CAN High: Tan/Black: 5 Single Wire CAN: Lt. Green: BCM - X6 connector (-) Parking Lights Output: Green/Black: 0 (+) Accessory Output: White/Red: 2 (-) RAP Off Output: Lt. Blue/Black: 3 Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. (+) 2V: Red/White, pin (-) Drivers Door Trigger: Gray/Black, pin 0 OR Hood Pin (-) Hood Input: Gray: 3 2: Brown: (+) 2V Input 0: Red: (+) 2V Input 9: Black: (-) Ground Drivers Window Switch (in drivers door) Siren (+) Siren Output: Brown: 7 6: Yellow: (+) Ignition Output 5: Orange/Red: Immobilizer Interrupt (vehicle side) 8 4: Yellow/Red: Immobilizer Interrupt (conn. side) (+) Immobilizer Power: Red/White, pin CUT (-) Driver Door Trigger: Gray/Black: pin 3 Ignition Barrel Ignition Switch Connector (green conn.) Immobilizer Control Module (under ignition switch) (+) Ignition: Pink, pin 3 (+) Accessory: Yellow, pin 23 Directed Digital Solutions GM

24 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Chevrolet Captiva Sport Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink 3 (+) Ignition Switch. Green 6 B Accessory Yellow (+) Ignition Switch. Green 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM below radio, X4 Black 25 D Parking Lights Lt. Blue 8 (-) BCM below radio, X2 White 25 D "OUT " Saturn VUE (V6) Gray/Black 0 (-) BCM below radio, X6 Pink 25 D Gray/Black 3 (-) Drivers window switch. Brown 6 E Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink 3 (+) Ignition Switch. Green 6 B Accessory Yellow (+) Ignition Switch. Green 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) BCM in center dash below radio, X4 Parking Lights Lt. Blue 8 (-) BCM in center dash below radio, X2 "OUT " Gray/Black 0 (-) BCM in center dash below radio, X6 Black 25 D White 25 D Pink 25 D Gray/Black 3 (-) Drivers window switch. Brown 6 E 24 Directed Digital Solutions GM

25 Type 5 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ). BCM - X2 connector (-) Parking Lights: Brown/White, pin 8 HS CAN High: Tan/Black or Tan/White, pin 6 Single Wire CAN: Dk. Green, pin 8 OBDII Plug Black Connector 9 6 HS CAN Low: Tan, pin 4 X7 X6 X5 X4 X3 X2 X BCM (in center console below the radio) HS CAN Low: Tan: 4 BCM - X4 connector BCM - X6 connector HS CAN High: Tan/Black: 5 Single Wire CAN: Lt. Green: 6 (-) Parking Lights Output: Green/Black: 0 (+) Accessory Output: White/Red: 2 (-) RAP Off Output: Lt. Blue/Black: 3 Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position (+) 2V: Red/White, Pin (-) Drivers Door Trigger: Gray/Black, pin 0 OR Hood Pin (-) Hood Input: Gray: 3 2: Brown: (+) 2V Input 0: Red: (+) 2V Input Drivers Window Switch (in drivers door) 9: Black: (-) Ground (+) Siren Output: Brown: 7 6: Yellow: (+) Ignition Output 8 Siren 5: Orange/Red: Immobilizer Interrupt (vehicle side) : Yellow/Red: Immobilizer Interrupt (conn. side) (+) Immobilizer Power: Red/White or Yellow, pin CUT (-) Driver Door Trigger: Gray/Black: pin 3 Ignition Barrel Ignition Switch Connector Immobilizer Control Module (under ignition switch) (+) Accessory: Brown oryellow, pin 2 (+) Ignition: Pink, pin 25 Directed Digital Solutions GM

26 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Chevrolet Equinox Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink (+) Ignition switch. Black 6 B Accessory Brown 2 (+) Ignition switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) Parking Lights Brown/White 8 (-) "OUT " Pontiac Torrent Gray/Black 0 (-) BCM in center console below radio, X4 BCM in center console below radio, X2 BCM in center console below radio, X6 Black 25 D White 25 D Pink 25 D Gray/Black 3 (-) Drivers window switch. Brown 6 E Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink (+) Ignition switch. Black 6 B Accessory Brown 2 (+) Ignition switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) Parking Lights Brown/White 8 (-) "OUT " Gray/Black 0 (-) BCM in center console below radio, X4 BCM in center console below radio, X2 BCM in center console below radio, X6 Black 25 D White 25 D Pink 25 D Gray/Black 3 (-) Drivers window switch. Brown 6 E 26 Directed Digital Solutions GM

27 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Saturn VUE (4-Cylinder) Immobilizer Interrupt Red/White (+) Immobilizer control module. Black 5 A Ignition Pink (+) Ignition switch. Black 6 B Accessory Brown 2 (+) Ignition switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) Parking Lights Lt. Blue 8 (-) "OUT " Suzuki XL Gray/Black 0 (-) BCM in center dash below radio, X4 BCM in center dash below radio, X2 BCM in center dash below radio, X6 Black 26 D White 25 D Pink 25 D Gray/Black 3 (-) Drivers window switch. Brown 6 E Immobilizer Interrupt Yellow (+) Immobilizer control module. Black 5 A Ignition Pink (+) Ignition switch. Black 6 B Accessory Brown 2 (+) Ignition switch. Black 6 B HS CAN High Tan/Black or Tan/White 6 Data OBDII diagnostic Black 6 C HS CAN Low Tan 4 Data OBDII diagnostic Black 6 C SW CAN Green Data OBDII diagnostic Black 6 C (+) 2V Red/White (+) Parking Lights Brown/White 8 (-) "OUT " Gray/Black 0 (-) BCM in center console below radio, X4 BCM in center console below radio, X2 BCM in center console below radio, X6 Black 26 D White 25 D Pink 25 D Gray/Black 3 (-) Drivers window switch. Brown 6 E 27 Directed Digital Solutions GM

28 Connecting the module Important! Before connecting the Directed Digital Solutions, it is important to ensure that the proper feature and function programming is selected using the configuration wizard. Visit to use the latest version of the online tool. Flashing a module using your computer:. Disconnect the main module from any (+) 2V power source, then connect it to your computer using the XKLoader2. 2. Go to using Internet Explorer; the configuration wizard will be displayed automatically. 3. Follow the instructions in the pop up window that will be displayed when the module is detected. Flashing a module using your smartphone or tablet:. Disconnect the main module from any (+) 2V power source, then connect it to the XKLoader3. 2. Launch the Directechs Mobile app on your smartphone or tablet. 3. Select FLASH YOUR MODULE and follow the on-screen instructions. When the flashing operation is successful, you can proceed with the instructions below. Manual or automatic transmission selection The yellow loop on the Directed Digital Solutions controls which transmission type the unit is configured for. The state of the loop (uncut or cut) when the main module is powered up will determine which type is selected. Uncut (default): Manual transmission. Cut: Automatic transmission. For safety reasons, all Directed Digital Solutions are shipped ready to use with a manual transmission (the yellow loop is untouched). If the loop is cut after power has been applied, it is necessary to cycle power to the main module (via the white 2- pin main power harness) so the unit will see the state change on the loop and appropriately configure the transmission type. Ready mode To successfully remote start a vehicle equipped with a manual transmission, the Ready Mode feature must be enabled before exiting the vehicle. Please refer to the Owner s Guide for more details on this required process. Additional connections required for vehicles equipped with a manual transmission (if not supported by firmware) Connection (-) E-Brake Status Input (Black/White, pin 2) (-) Door Trigger Input (White/Green, pin 0) OR (+) Door Input (Yellow/ Green, pin ) (AC) Tachometer Input (Violet/White, pin 6) Description Must be connected to a working emergency brake in the vehicle. Although most vehicles have simple (-) trigger emergency brake circuits note some vehicles do not and may require unique integration methodologies. Must be connected to a working door trigger in the vehicle, which monitors all doors. The unit must monitor the door pins to allow the Ready Mode process to be enabled. Note: Some vehicles may require unique integration methodologies for this circuit. For more information, refer to Must be connected to a working tachometer signal in the vehicle (fuel injector, ignition coil, true tach, etc.) and learned successfully to the Directed Digital Solutions. 28 Directed Digital Solutions GM

29 Optional sensors Note: The sensor port is only active on hybrid systems. The 4-pin sensor port is compatible with a number of different Directed sensors including, but not limited to: Shock Sensor 504D Field Disturbance Sensor 508D Ultrasonic Sensor 509U Note: In the case of 508D, power and ground must be hardwired to the vehicle power and ground should NOT be obtained from the 4-pin sensor port. Each sensor will have its own instructions, which must be followed for installation and adjustment. RF Systems An RF System consists of one or multiple remotes, a Control Center (antenna), and an antenna cable various combinations exist. An RF System allows the vehicle owner to control the system with enhanced range. Two-way models are available. Please follow the instructions included with the kit for appropriate installation and programming information. When flashing the Directed Digital Solutions, make sure to pick the remote you will be using. This way the main module will have the necessary firmware to interact with the remote and Control Center (antenna) combination. When used in conjunction with SmartStart Disconnect power from the Directed Digital Solutions before connecting the SmartStart module. Failing to do so could damage main module. To enable D2D communication between the Directed Digital Solutions and the SmartStart one of the following actions must be executed: SmartStart with Loops The brown loop must be cut. SmartStart with Pigtails The gray wire must be connected to a ground source. Loops Pigtails DO NOT connect the SmartStart 2-pin power harness when using the Directed Digital Solutions. Power and ground will be provided by the D2D connector on main module. Refer to the SmartStart documentation for further details. 29 Directed Digital Solutions GM

30 Module programming Refer to "LED diagnostics and troubleshooting" on page 3 for more information and for troubleshooting purposes. To connect the module: 2 Please ensure that the vehicle is in a safe location and cannot move forward during programming. For vehicles equipped with a manual transmission, make sure the gearshift lever is in the neutral position. Connect all the harnesses to the Directed Digital Solutions, EXCEPT the 2-pin main power harness. Connect all but the 2-pin harness 3 Connect the 2-pin main power harness, and wait until the LED turns ON solid red. Must be connected LAST & Solid 4 Insert and turn the key to the ON position. The LED turns ON solid green for 3 seconds, Key IN START & & then shuts off. It may take up to minute. Solid x 3 secs Off OFF ON Key OUT 5 Turn vehicle ignition OFF once the module is successfully programmed. START OFF ON 6 7 Pair remotes (if applicable). For information on how to pair a specific remote, please refer to its corresponding owner documentation, which can be found inside the product packaging of the complete system or on By default, the tachometer is preprogrammed for the vehicle. For instructions on how to program tach, see page 34. Pair remotes* Initialize tachometer * Your aftermarket remote may differ from the model shown in the illustrations. You have successfully completed the module programming sequence. 30 Directed Digital Solutions GM

31 LED diagnostics and troubleshooting This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation. Module programming LED Description Troubleshooting Module has no power. Make sure the D2D harness is connected and that 2 Volt is present between the red and black wires. If 2 Volt is present, the module may be defective. Waiting to begin the programming sequence. Ensure the correct programming procedure is being followed. Initialization failed. Reset the module and complete the programming again. If the issue persists, please contact Technical Support. Transponder functions were skipped. (If compatible) when the RXT mode is not desired or convenience features are needed, please reset and reprogram the module. All required CAN networks has been detected. Normal operation. of 2 CAN networks has been detected. Normal operation. Key2GO initiated. Please follow the steps indicated in "Pre-installation and application warnings" on page 4 to complete the Key2GO programming. Solid green x 3 secs Module was successfully programmed with all functions. Normal operation. Solid orange x 3 secs Module was successfully programmed without transponder functions. Normal operation. Off Solid red Flashes red & green Solid orange Flashes green Flashes orange Flashes orange slowly Module programming Error codes LED Flashes red x Flashes red x Flashes red x 2 Flashes red x 3 Flashes red x 4 Flashes red x 5 Flashes red x 6 Flashes red x 7 Description Troubleshooting CAN2 not detected. Check the CAN2 Orange/Green and Orange/Brown wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times. J850 not detected. Check the J850 wire connection. Wake up the data bus by turning the ignition on and try again. CAN not detected. Check the CAN Tan and Tan/Black wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times. Bypass data not detected. Check the bypass line connection. If more than one wire is used, make sure they are not inverted. Ensure the vehicle still operates correctly using the factory key. Bypass processing error. The bypass calculation failed. Reset the module and try again. If the condition persists, please contact Technical Support. ISO not detected. The Yellow/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams, fuse selection & vehicle wiring reference charts)" on page 8 to check the connections. ISO 2 not detected. The Orange/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams, fuse selection & vehicle wiring reference charts)" on page 8 to check the connections. MUX not detected. The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to "Installation (wiring diagrams, fuse selection & vehicle wiring reference charts)" on page 8 to check the connections. External module synchronization LED Description Troubleshooting (Flashes red, red, then orange) x 0 OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. 3 Directed Digital Solutions GM

INSTALLATION GUIDE. Directed Digital Solutions HONDA4. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions HONDA4. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions HONDA4 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to

More information

INSTALLATION GUIDE. Directed Digital Solutions HKHT1. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions HKHT1. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions HKHT1 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to

More information

Directed Digital System

Directed Digital System Directed Digital System HYUNDAI2 Firmware Specific Guide This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional

More information

INSTALLATION GUIDE. Directed Digital Solutions GM5. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions GM5. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions GM5 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

INSTALLATION GUIDE. Directed Digital Solutions TL6. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions TL6. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions TL6 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

INSTALLATION GUIDE. Directed Digital Solutions TL5. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions TL5. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions TL5 Designed by Installers for Installers 07 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

DS4+ INSTALLATION GUIDE TL10. Designed by Installers for Installers

DS4+ INSTALLATION GUIDE TL10. Designed by Installers for Installers INSTALLATION GUIDE DS+ TL0 Designed by Installers for Installers 0 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person

More information

INSTALLATION GUIDE. Directed Digital Solutions FORD4. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions FORD4. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions FORD Designed by Installers for Installers 0 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

INSTALLATION GUIDE. Directed Digital Solutions GM4. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions GM4. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions GM4 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

Vehicle Application Guide... Installation (Wiring Diagram & Vehicle Wiring Reference Charts)...

Vehicle Application Guide... Installation (Wiring Diagram & Vehicle Wiring Reference Charts)... Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The GM

More information

INSTALLATION GUIDE. Directed Digital Solutions FORD6. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions FORD6. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions FORD6 Designed by Installers for Installers 208 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to

More information

INSTALLATION GUIDE. Directed Digital Solutions NISS3HT. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions NISS3HT. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions NISS3HT Designed by Installers for Installers 208 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to

More information

INSTALLATION GUIDE. Directed Digital Solutions GM2. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions GM2. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions GM2 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

INSTALLATION GUIDE. Directed Digital Solutions TL11. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions TL11. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions TL11 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to

More information

INSTALLATION GUIDE. Directed Digital Solutions FORD6. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions FORD6. Designed by Installers for Installers INSTALLATI GUIDE Directed Digital Solutions FORD6 Designed by Installers for Installers 2016 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

INSTALLATION GUIDE. Directed Digital Solutions MIT2. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions MIT2. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions MIT2 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to

More information

INSTALLATION GUIDE. Directed Digital Solutions HK7. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions HK7. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions HK7 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

INSTALLATION GUIDE. Directed Digital Solutions MIT6. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions MIT6. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions MIT6 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to

More information

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER13. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER13. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions CHRYSLER13 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

INSTALLATION GUIDE. Directed Digital Solutions FORD12. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions FORD12. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions FORD12 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to

More information

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER10. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER10. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions CHRYSLER10 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

Directed Digital System

Directed Digital System Directed Digital System TL Firmware Specific Guide This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional

More information

INSTALLATION GUIDE. Directed Digital Solutions TL1. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions TL1. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions TL Designed by Installers for Installers 207 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

INSTALLATION GUIDE. Directed Digital Solutions VW08. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions VW08. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions VW08 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to

More information

INSTALL GUIDE FLC-GM(RS)-GM10-[FLRSGM10]-EN

INSTALL GUIDE FLC-GM(RS)-GM10-[FLRSGM10]-EN INSTALL GUIDE DOCUMENT NUMBER 9 REVISION DATE FIRMWARE FLC-GM(RS)-GM0-[FLRSGM0] HARDWARE FLRSGM0 ACCESSORIES FLPROG (REQUIRED) FLRF// (OPTIONAL) CARLINK ASCL (OPTIONAL) NOTICE The manufacturer will accept

More information

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER7. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER7. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions CHRYSLER7 Designed by Installers for Installers 2016 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

INSTALL GUIDE OEM-GM(RS)-GM10-[OL-RS-GM10]-EN

INSTALL GUIDE OEM-GM(RS)-GM10-[OL-RS-GM10]-EN INSTALL GUIDE OEM-GM(RS)-GM0-[OL-RS-GM0]-EN DOCUMENT NUMBER 555 REVISION DATE 05 FIRMWARE OEM-GM(RS)-GM0-[OL-RS-GM0] HARDWARE OL-RS-GM0 ACCESSORIES OL-LOADER (REQUIRED) NOTICE The manufacturer will accept

More information

Vehicle Application Guide...

Vehicle Application Guide... Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide Door

More information

DS4+ INSTALLATION GUIDE GM2. Designed by Installers for Installers

DS4+ INSTALLATION GUIDE GM2. Designed by Installers for Installers INSTALLATION GUIDE DS4+ GM2 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by

More information

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER6. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER6. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions CHRYSLER6 Designed by Installers for Installers 208 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

INSTALLATION GUIDE. Directed Digital Solutions NISS2HT. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions NISS2HT. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions NISS2HT Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

DS4+ INSTALLATION GUIDE TL11. Designed by Installers for Installers

DS4+ INSTALLATION GUIDE TL11. Designed by Installers for Installers INSTALLATION GUIDE DS4+ TL11 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by

More information

Directed Digital System

Directed Digital System Directed Digital System MIT4 Firmware Specific Guide This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional

More information

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER12. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions CHRYSLER12. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions CHRYSLER2 Designed by Installers for Installers 207 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

INSTALLATION GUIDE Chevrolet Silverado GM Designed by Installers for Installers

INSTALLATION GUIDE Chevrolet Silverado GM Designed by Installers for Installers INSTALLATION GUIDE DB3 2010 Chevrolet Silverado 1500. 403.GM11 1.08 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only!

More information

INSTALL GUIDE FLC-GM(RS)-GM10-[FLRSGM10]-EN

INSTALL GUIDE FLC-GM(RS)-GM10-[FLRSGM10]-EN INSTALL GUIDE DOCUMENT NUMBER 498 REVISION DATE 0804 FIRMWARE FLC-GM(RS)-GM0-[FLRSGM0] HARDWARE FLRSGM0 ACCESSORIES FLPROG (REQUIRED) FLRF//4 (OPTIONAL) CARLINK ASCL (OPTIONAL) TERMS OF USE: Automotive

More information

INSTALLATION GUIDE. Directed Digital Solutions TL3. Designed by Installers for Installers

INSTALLATION GUIDE. Directed Digital Solutions TL3. Designed by Installers for Installers INSTALLATION GUIDE Directed Digital Solutions TL3 Designed by Installers for Installers 206 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install

More information

INSTALL GUIDE OL-GM(RS)-GM10-[OL-RS-GM10]-EN

INSTALL GUIDE OL-GM(RS)-GM10-[OL-RS-GM10]-EN INSTALL GUIDE DOCUMENT NUMBER 54253 REVISION DATE 20180918 FIRMWARE OL-GM(RS)-GM10-[OL-RS-GM10] HARDWARE OL-RS-GM10 ACCESSORIES OL-LOADER (REQUIRED) RF-10/30/50-EDP (OPTIONAL) LINKR (OPTIONAL) TERMS OF

More information

DS4+ INSTALLATION GUIDE GM9. Designed by Installers for Installers

DS4+ INSTALLATION GUIDE GM9. Designed by Installers for Installers INSTALLATION GUIDE DS4+ GM9 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by

More information

INSTALLATION GUIDE Chevrolet Impala GM Designed by Installers for Installers

INSTALLATION GUIDE Chevrolet Impala GM Designed by Installers for Installers INSTALLATION GUIDE DB3 2001 Chevrolet Impala - 403.GM2 4.04 Designed by Installers for Installers 2016 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

GM3. Audiovox Electronics Corp.

GM3. Audiovox Electronics Corp. Audiovox Electronics Corp. INSTALL GUIDE FLC-AL(DL)-GM3-EN Available for : FLCAN Rev. Date: June, 202 Doc. No.: ##9336## 2020607 GM3 please visit www.flash-it.com for complete product details The brand

More information

Important! This product is NOT compatible with vehicles equipped with a manual transmission. Vehicle Application Guide...

Important! This product is NOT compatible with vehicles equipped with a manual transmission. Vehicle Application Guide... Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide Door

More information

Automotive Data Solutions Inc. Rev. Date: June 11, 2012 Doc. No.: ##9333##

Automotive Data Solutions Inc. Rev. Date: June 11, 2012 Doc. No.: ##9333## Automotive Data Solutions Inc. INSTALL GUIDE ADS-DL-3-EN Available for : ADS-DL Rev. Date: June, 202 Doc. No.: ##9333## 2020607 3 Version FRançaise disponible en ligne au www.idatalink.com please visit

More information

DS4+ INSTALLATION GUIDE VW08. Designed by Installers for Installers

DS4+ INSTALLATION GUIDE VW08. Designed by Installers for Installers INSTALLATION GUIDE DS4+ VW08 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by

More information

Directed Digital System

Directed Digital System Directed Digital System GM0 Firmware Specific Guide This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional

More information

Directed Digital System

Directed Digital System Directed Digital System AUDI02 Firmware Specific Guide This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional

More information

INSTALLATION GUIDE Chevrolet Spark GM Designed by Installers for Installers

INSTALLATION GUIDE Chevrolet Spark GM Designed by Installers for Installers INSTALLATION GUIDE DB3 2015 Chevrolet Spark - 403.GM10 4.07 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

DS4+ INSTALLATION GUIDE FORD12. Designed by Installers for Installers

DS4+ INSTALLATION GUIDE FORD12. Designed by Installers for Installers INSTALLATION GUIDE DS4+ FORD12 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product

More information

INSTALLATION GUIDE Dodge/Ram CHRYSLER Designed by Installers for Installers

INSTALLATION GUIDE Dodge/Ram CHRYSLER Designed by Installers for Installers INSTALLATION GUIDE DB3 2016 Dodge/Ram 1500-403.CHRYSLER6 2.04 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

INSTALLATION GUIDE Toyota Corolla (H Key) TL Designed by Installers for Installers

INSTALLATION GUIDE Toyota Corolla (H Key) TL Designed by Installers for Installers INSTALLATION GUIDE DB3 2017 Toyota Corolla (H Key) - 403.TL10 2.18 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only!

More information

DS4+ INSTALLATION GUIDE CHRYSLER12. Designed by Installers for Installers

DS4+ INSTALLATION GUIDE CHRYSLER12. Designed by Installers for Installers INSTALLATION GUIDE DS4+ CHRYSLER2 Designed by Installers for Installers 7 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product

More information

INSTALLATION GUIDE Honda Accord HONDA Designed by Installers for Installers

INSTALLATION GUIDE Honda Accord HONDA Designed by Installers for Installers INSTALLATION GUIDE DB3 2011 Honda Accord - 403.HONDA56 3.22 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

INSTALLATION GUIDE Toyota Camry (G Key) TL Designed by Installers for Installers

INSTALLATION GUIDE Toyota Camry (G Key) TL Designed by Installers for Installers INSTALLATION GUIDE DB3 2013 Toyota Camry (G Key) - 403.TL5 4.00 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only!

More information

install guide OEM-GM(RS)-GM10-[FLRSGM10]-EN

install guide OEM-GM(RS)-GM10-[FLRSGM10]-EN install guide Document number 13581 Revision Date 2420 firmware OEM-GM(RS)-GM10-[FLRSGM10] hardware FLRSGM10 accessories FLPROG (REQUIRED) NOTICE The manufacturer will accept no responsability for any

More information

The SUBARU1 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Subaru vehicles.

The SUBARU1 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Subaru vehicles. Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The SUBARU

More information

INSTALLATION GUIDE Chevrolet Cruze GM Designed by Installers for Installers

INSTALLATION GUIDE Chevrolet Cruze GM Designed by Installers for Installers INSTALLATION GUIDE DB3 2011 Chevrolet Cruze - 403.GM10 4.12 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

The HYUNDAI4 firmware for DBALL2 is an all-in-one door lock and override module compatible with. Vehicle Application Guide...

The HYUNDAI4 firmware for DBALL2 is an all-in-one door lock and override module compatible with. Vehicle Application Guide... Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The HYUNDAI4

More information

This module can only be flashed and configured using XpressVIP at or using the Directechs

This module can only be flashed and configured using XpressVIP at   or using the Directechs Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The NISS08

More information

INSTALLATION GUIDE Dodge/Ram Grand Caravan CHRYSLER Designed by Installers for Installers

INSTALLATION GUIDE Dodge/Ram Grand Caravan CHRYSLER Designed by Installers for Installers INSTALLATION GUIDE DB3 2014 Dodge/Ram Grand Caravan - 403.CHRYSLER 7.23 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer

More information

Directed Digital System

Directed Digital System Directed Digital System VW02 Firmware Specific Guide This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional

More information

INSTALLATION GUIDE Toyota Camry (Smart Key). 933.TL Designed by Installers for Installers

INSTALLATION GUIDE Toyota Camry (Smart Key). 933.TL Designed by Installers for Installers INSTALLATION GUIDE DS4+ 2010 Toyota Camry (Smart Key). 933.TL1 5.02.179 Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer

More information

This module can only be flashed and configured using XpressVIP at or using the Directechs

This module can only be flashed and configured using XpressVIP at  or using the Directechs Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The HYUNDAI

More information

INSTALLATION GUIDE Acura TL (Smart Key). 933.HONDA Designed by Installers for Installers

INSTALLATION GUIDE Acura TL (Smart Key). 933.HONDA Designed by Installers for Installers INSTALLATION GUIDE DS4+ 202 Acura TL (Smart Key). 933.HONDA56 3.26.85 Designed by Installers for Installers 207 Directed, Vista CA This product is intended for installation by a professional installer

More information

The GM9 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Buick, Cadillac, Chevrolet and GMC vehicles.

The GM9 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Buick, Cadillac, Chevrolet and GMC vehicles. Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The GM9

More information

GM3. Audiovox Electronics Corp.

GM3. Audiovox Electronics Corp. Audiovox Electronics Corp. GM INSTALL GUIDE FLC-AL(DL)-GM-EN Available for : FLCAN Rev. Date: January, 0 Doc. No.: ##7## please visit for complete product details The brand names and logos found in this

More information

The NISS3HT firmware for DBALL2 is an all-in-one door lock and override module compatible with. Vehicle Application Guide...02

The NISS3HT firmware for DBALL2 is an all-in-one door lock and override module compatible with. Vehicle Application Guide...02 Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The NISS3HT

More information

The TL1 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific TOYOTA and LEXUS vehicles.

The TL1 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific TOYOTA and LEXUS vehicles. Platform: DBALL Firmware: TL Rev.: 005 Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing

More information

The SUBARU3 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Subaru vehicles.

The SUBARU3 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Subaru vehicles. Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The SUBARU3

More information

The TL4 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Toyota and Lexus vehicles.

The TL4 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Toyota and Lexus vehicles. Rev.: 0700 Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation

More information

The FORD3 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Ford and Lincoln vehicles.

The FORD3 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Ford and Lincoln vehicles. Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The firmware

More information

Vehicle Application Guide... Key2GO...

Vehicle Application Guide... Key2GO... Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide Door

More information

INSTALLATION GUIDE Nissan Altima (Smart Key) NISS3HT 3.08 RSR. Designed by Installers for Installers

INSTALLATION GUIDE Nissan Altima (Smart Key) NISS3HT 3.08 RSR. Designed by Installers for Installers INSTALLATION GUIDE DB3 2009 Nissan Altima (Smart Key) - 403.NISS3HT 3.08 RSR Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer

More information

INSTALLATION GUIDE Mazda 6 (Smart Key) MA RSR. Designed by Installers for Installers

INSTALLATION GUIDE Mazda 6 (Smart Key) MA RSR. Designed by Installers for Installers INSTALLATION GUIDE DB3 2009 Mazda 6 (Smart Key) - 403.MA1 4.00 RSR Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only!

More information

Alarms & Remote Start

Alarms & Remote Start Alarms & Remote Start INSTALL GUIDE OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN DOCUMENT NUMBER 990 REVISION DATE 008 FIRMWARE OEM-AL(RS)-CH0-[OL-MDB-ALL] HARDWARE OL-MDB-ALL ACCESSORIES OL-LOADER (REQUIRED) NOTICE

More information

Important! This product is NOT compatible with vehicles equipped with a manual transmission.

Important! This product is NOT compatible with vehicles equipped with a manual transmission. Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The TL

More information

Important! NOT compatible with vehicles equipped with a manual transmission. Vehicle Application Guide...02

Important! NOT compatible with vehicles equipped with a manual transmission. Vehicle Application Guide...02 Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The NISS3HT

More information

Important! This product is NOT compatible with vehicles equipped with a manual transmission. Vehicle Application Guide...

Important! This product is NOT compatible with vehicles equipped with a manual transmission. Vehicle Application Guide... Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The CHRYSLER9

More information

INSTALL GUIDE OEM-AL(RS)-NI9-[FLCAN]-EN

INSTALL GUIDE OEM-AL(RS)-NI9-[FLCAN]-EN INSTALL GUIDE DOCUMENT NUMBER 5506 REVISION DATE 08098 FIRMWARE OEM-AL(RS)-NI9-[FLCAN] HARDWARE FLCAN ACCESSORIES FLPROG (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly

More information

Vehicle Application Guide... Installation (Wiring Diagrams & Vehicle Wiring Reference Charts) Type 1... Type 2... Type 3...

Vehicle Application Guide... Installation (Wiring Diagrams & Vehicle Wiring Reference Charts) Type 1... Type 2... Type 3... Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide Door

More information

Alarms & Remote Start

Alarms & Remote Start Alarms & Remote Start INSTALL GUIDE DOCUMENT NUMBER 80 REVISION DATE 008 FIRMWARE OEM-AL(RS)-VW-[OL-MDB-ALL] HARDWARE OL-MDB-ALL ACCESSORIES OL-LOADER (REQUIRED) NOTICE The manufacturer will accept no

More information

INSTALL GUIDE OEM-GM(RS)-GM2-[OL-RS-GM2]-EN

INSTALL GUIDE OEM-GM(RS)-GM2-[OL-RS-GM2]-EN INSTALL GUIDE OEM-GM(RS)-GM-[OL-RS-GM]-EN DOCUMENT NUMBER 0 REVISION DATE 0 FIRMWARE OEM-GM(RS)-GM-[OL-RS-GM] HARDWARE OL-RS-GM ACCESSORIES OL-LOADER (REQUIRED) NOTICE The manufacturer will accept no responsability

More information

INSTALL GUIDE OEM-AL(RS)-NI8-[FLCAN]-EN

INSTALL GUIDE OEM-AL(RS)-NI8-[FLCAN]-EN INSTALL GUIDE DOCUMENT NUMBER 5679 REVISION DATE 084 FIRMWARE OEM-AL(RS)-NI8-[FLCAN] HARDWARE FLCAN ACCESSORIES FLPROG (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly

More information

The FORD12 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Ford and Lincoln

The FORD12 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Ford and Lincoln Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The FORD12

More information

GUIDE ID: GM VEHICLE COMPATIBILITY. Make Model Trim Years Firmware Diag

GUIDE ID: GM VEHICLE COMPATIBILITY. Make Model Trim Years Firmware Diag Page 1 of 6 MODEL OL-HRN-RS-GM10 GUIDE ID GM1020180131 AVAILABLE ACCESSORIES OL-HRN-RS-PWR (Adapt to any brand remote start) DISCLAIMER: The manufacturer of this product nor its affiliates accept any responsibility

More information

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: May 16, 2017 Doc. No.: ##39298##

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: May 16, 2017 Doc. No.: ##39298## Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-GM1-EN AVAILABLE FOR : ADS-AL CA Rev. Date: May 16, 2017 Doc. No.: ##39298## GM1 U.S. PATENT NO. 8,856,780 PLEASE VISIT WWW.IDATALINK.COM FOR COMPLETE

More information

Alarms & Remote Start

Alarms & Remote Start Alarms & Remote Start INSTALL GUIDE DOCUMENT NUMBER 809 REVISION DATE 0608 FIRMWARE COL-AL(RS)-VW6-[OL-MDB-ALL] HARDWARE OL-MDB-ALL ACCESSORIES OL-LOADER (REQUIRED) OMEGA-CARLINK-GPS (OPTIONAL) NOTICE

More information

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: March 6, 2019 Doc. No.: ##59564##

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: March 6, 2019 Doc. No.: ##59564## Automotive Data Solutions Inc. ADS-AL(DL)-GM1-EN AVAILABLE FOR : ADS-AL CA Rev. Date: March 6, 2019 Doc. No.: ##59564## GM1 PATENT NO. US 8,856,780 CA 2759622 PLEASE VISIT WWW.IDATALINK.COM FOR COMPLETE

More information

DS4+ INSTALLATION GUIDE. Analog Mode (Viper & Automate) Designed by Installers for Installers

DS4+ INSTALLATION GUIDE. Analog Mode (Viper & Automate) Designed by Installers for Installers INSTALLATION GUIDE DS4+ Analog Mode (Viper & Automate) Designed by Installers for Installers 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts

More information

Automotive Data Solutions Inc. Rev. Date: November 16, 2012 Doc. No.: ##10129##

Automotive Data Solutions Inc. Rev. Date: November 16, 2012 Doc. No.: ##10129## Automotive Data Solutions Inc. INSTALL GUIDE DBI-AL(DL)-GM-EN Available for : DBI-AL CA Rev. Date: November, 0 Doc. No.: ##09## 0 GM Version FRançaise disponible en ligne au www.idatalink.com please visit

More information

Important! This product is NOT compatible with vehicles equipped with a manual transmission.

Important! This product is NOT compatible with vehicles equipped with a manual transmission. Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide This

More information

Automotive Data Solutions Inc. Rev. Date: October 04, 2011 Doc. No.: ##6617##

Automotive Data Solutions Inc. Rev. Date: October 04, 2011 Doc. No.: ##6617## Automotive Data Solutions Inc. INSTALL GUIDE DBI-AL(DL)-GM GM Available for : DBI-AL CA Rev. Date: October 04, 0 Doc. No.: ##667## 0004 Version FRançaise disponible en ligne au www.idatalink.com please

More information

Important! This product is NOT compatible with vehicles equipped with a manual transmission. Vehicle Application Guide...

Important! This product is NOT compatible with vehicles equipped with a manual transmission. Vehicle Application Guide... Platform: DBALL Rev.: 058 Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.

More information

Vehicle Application Guide... Installation Type 1... Type 2... Type 3... Wiring Reference Charts...

Vehicle Application Guide... Installation Type 1... Type 2... Type 3... Wiring Reference Charts... Platform: DBALL/DBALL Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation

More information

U.S. Patent No. 8,856,780 INSTALL TYPE SELECTION. features. PoWer SlIDInG Door (r) rap SHUtDoWn ctrl rear DefroSt ctrl* PoWer SlIDInG Door (l)

U.S. Patent No. 8,856,780 INSTALL TYPE SELECTION. features. PoWer SlIDInG Door (r) rap SHUtDoWn ctrl rear DefroSt ctrl* PoWer SlIDInG Door (l) Automotive Data Solutions Inc. INSTALL GUIDE ADS-DL-1-EN AVAILABLE FOR : ADS-DL Rev. Date: May 16, 2017 Doc. No.: ##39300## 1 U.S. PATENT NO. 8,856,780 PLEASE VISIT WWW.IDATALINK.COM FOR COMPLETE PRODUCT

More information

GM2. Alarms & Remote Start. Automotive Data Solutions Inc.

GM2. Alarms & Remote Start. Automotive Data Solutions Inc. Alarms & Remote Start Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-GM Available for : ADS-AL CA Rev. Date: March 3, 0 Doc. No.: ##8855## 003 GM The brand names and logos found in this guide

More information

INSTALL GUIDE OEM-AL(RS)-TL7-[FLCAN]-EN

INSTALL GUIDE OEM-AL(RS)-TL7-[FLCAN]-EN INSTALL GUIDE DOCUMENT NUMBER 545 REVISION DATE 08098 FIRMWARE OEM-AL(RS)-TL7-[FLCAN] HARDWARE FLCAN ACCESSORIES FLPROG (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly

More information

GM2 OL-AL(MDB)-GM2. Available for : OL-MDB-ALL. please visit for complete product details

GM2 OL-AL(MDB)-GM2. Available for : OL-MDB-ALL. please visit   for complete product details Omega R&D Inc. INSTALL GUIDE OL-AL(MDB)-GM Available for : OL-MDB-ALL Rev. Date: March 3, 0 Doc. No.: ##887## 003 GM please visit www.caralarm.com for complete product details The brand names and logos

More information

INSTALL GUIDE OEM-GM(RS)-GM2-[ADS-GM2]-EN

INSTALL GUIDE OEM-GM(RS)-GM2-[ADS-GM2]-EN INSTALL GUIDE DOCUMENT NUMBER 0 REVISION DATE FIRMWARE OEM-GM(RS)-GM-[ADS-GM] HARDWARE ADS-GM ACCESSORIES ADS-USB (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical damage

More information

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: May 31, 2017 Doc. No.: ##39828##

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: May 31, 2017 Doc. No.: ##39828## Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-GM-EN AVAILABLE FOR : ADS-AL CA Rev. Date: May 3, 07 Doc. No.: ##3988## GM U.S. PATENT NO. 8,856,780 PLEASE VISIT WWW.IDATALINK.COM FOR COMPLETE

More information

The optional Plug & Play T-Harness THCHD3 (sold separately) provides simpler and faster installation.

The optional Plug & Play T-Harness THCHD3 (sold separately) provides simpler and faster installation. Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide This

More information