Maytag MLG32PDB. For Internal Use Only. (ADG-435 Parts Manual) RETAIN THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE

Size: px

Start display at page:

Download "Maytag MLG32PDB. For Internal Use Only. (ADG-435 Parts Manual) RETAIN THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE"

Barbra O’Brien’
5 years ago
Views:

1 Maytag MLG32PDB (ADG-435 Parts Manual) 1999 For Internal Use Only RETAIN THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE Maytag One Dependability Square Newton, Iowa (515) MFM/mt ADC Part No

2 Retain This Manual In A Safe Place For Future Reference This product embodies advanced concepts in engineering, design, and safety. If this product is properly maintained, it will provide many years of safe, efficient, and trouble-free operation. ONLY properly licensed technicians should service this equipment. OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment or specified in the installation/ operator's manual included with the dryer. FOR YOUR SAFETY POUR VOTRE SECURITE Do not store or use gasoline or other Ne pas entreporer ni utiliser d essence ni d flammable vapors or liquids in the autres vapeurs ou liquides inflammables dans le vicinity of this or any other appliance voisinage de cet appareil ou de yout autre appareil We have tried to make this manual as complete as possible and hope you will find it useful. Manufacturer reserves the right to make changes from time to time, without notice or obligation, in prices, specifications, colors, and material, and to change or discontinue models. Important For your convenience, log the following information: DATE OF PURCHASE DISTRIBUTORS NAME Serial Number(s) MODEL NO. MLG32PDB (ADG-435PDB) For replacement parts, contact the distributor from which the dryer was purchased or contact: MAYTAG 403 West Fourth St. North Newton, Iowa (515) The illustrations on the following pages may not depict your particular dryer exactly. The illustrations are a composite of the various dryer models. Be sure to check the descriptions of the parts thoroughly before ordering. IMPORTANT NOTE TO PURCHASER Information must be obtained from your local gas supplier on the instructions to be followed if the user smells gas. These instructions must be posted in a prominent location near the dryer.

3 Table of Contents Control Door Assembly... 2 Main Computer/Coin Acceptor Assembly... 3 Microprocessor (Computer) Assembly... 4 Microprocessor Control Box Assembly... 5 Main Door Assembly... 6 Upper Front Panel Assembly... 7 Lower Front Panel Assembly... 8 Main Door Switch Assembly... 9 Coin Vault Assembly Lint Door Assembly Lint Coop Assembly Lint Drawer (Basket) II Assembly Lint Drawer (Basket) Switch Assembly...14 Basket (Tumbler)/Support Assemblies Temperature Sensor Bracket Assembly...16 Tumbler Bearing Assembly Motor Mount Assembly Direct Spark Ignition (DSI) Gas Valve Train Assembly... 19, 20 Burner Box/Gas Piping Assemblies... 21, 22 Sail Switch Assembly... 23, 24 Idler Bearing Assembly Exhaust Ducting Assembly Back Guard Assembly... 27

4 2 Control Door Assembly White Hinged Control Door Assembly (includes illus. no. 1, 2, 4, 5, and 7) Beige Hinged Control Door Assembly (includes illus. no. 1, 2, 4, 5, and 7) Bisque Hinged Control Door Assembly (includes illus. no. 1, 2, 4, 5, and 7) Control Door Top Black Trim (29-5/8 length) DP Control Door Lock (keyed XX4451) #10-32 x 1/4 Phillips Pan Head Screw /4 x 3/8 Neoprene Sponge Tape (sold by the foot) #8-18 x 7/16 Phillips Pan Head Screw Maytag Control Display Label

5 Main Computer/Coin Acceptor Assembly Microprocessor (Computer) (refer to Microprocessor (Computer) Assembly on page 4) Control Door (refer to Control Door Assembly on page 2) Hanke 25 Coin Accepter Assembly (includes illus. no. 3 through 6) Optic Switch ONLY for Hanke 25 Coin Accepter #6-32 x 1 Phillips Round Head Machine Screw

6 4 Microprocessor (Computer) Assembly Microprocessor (Computer) Display Lens Microprocessor (Computer) Mounting Panel Membrane Switch Push Button Molex Membrane Switch /2 x 1/4 Nylon Stand Off Microprocessor (Computer) Board Only #6-32 x 1/4 Hex Nut Microprocessor (Computer) Board Cover #8 Phillips Pan Head Type A Screw Tinnerman U Clip Neoprene Sponge Tape (sold by foot) #10 Steel Burr #8-32 Hex Nut

7 Microprocessor Control Box Assembly Multi-Tap Transformer Assembly /2-Amp (Slo Blo) Fuse Pole Motor Contractor RC Network with Connectors L-70 Ground Lug Interconnect Board SPST (Single-Pole-Single-Throw) Rocker Switch #6-32 x 1/4 Phillips Head Machine Screw #8-32 Pal Nut #10-16 X 1/2 Hex Washer TEK Screw V Micro Transformer Assembly Pin Female Connector Socket Position Connector Socket Pin Connector Socket

8 6 Main Door Assembly Black Plastic Main Door Assembly (latch type) Complete with Mechanical Fasteners (includes illus. nos. 1 and 5 through 9) /2 Stainless Steel Main Door Hinge Assembly #10-24 x 3/8 Phillips Pan Head Taptite Screw /4-20 Free Spin Wash Nut Main Door Gasket /16 Door Glass with (4) Holes Main Door Gasket/Glass Adhesive (10.3 oz cartridge) /2 Stainless Steel Flat Head Allen Screw Door Glass (Nylon) Spacer Main Door Latch Screw (#10 x 7/16 Dome Hex Head Screw)

9 Upper Front Panel Assembly White Upper Front Panel without Hinge (includes illus. no. 1 through 3 and 6) Beige Upper Front Panel without Hinge (includes illus. no. 1 through 3 and 6) Bisque Upper Front Panel without Hinge (includes illus. no. 1 through 3 and 6) /8 Pop Rivet Friction Door Latch Kit (includes illus. nos. 2 and 3) Maytag Logo with Tape #10-16 x 1/2 Hex Head TEK Crimptite Screw Rubber Grommet

10 8 Lower Front Panel Assembly White Lower Front Panel Assembly Complete without Hinge (includes illus. no. 1 through 3 and 5) Beige Lower Front Panel Assembly Complete without Hinge (includes illus. no. 1 through 3 and 5) Bisque Lower Front Panel Assembly Complete without Hinge (includes illus. no. 1 through 3 and 5) /8 Pop Rivet Friction Door Latch Kit (includes illus. nos. 2 and 3) #10-16 x 1/2 Phillips Hex Head TEK Screw Rubber Grommet

11 Main Door Switch Assembly #6-32 Hex Nut #6 Lock Washer Single Pole Door Switch Insulated Female Terminal /8 Standard Nylon Spacer /2 Stainless Steel Main Door Hinge #6 Stud Main Door Switch Housing ONLY #10-32 x 1/4 Phillips Pan Head TEK Screw Rubber Grommet

12 10 Coin Vault Assembly Coin Box only with magnet With Coin Box Faceplate ONLY Beige Coin Box Faceplate ONLY Bisque Coin Box Faceplate ONLY Ace Lock Assembly With Key 3* Ace Key Only White Coin Vault ONLY Beige Coin Vault ONLY Lower Front Panel (refer to Lower Front Panel Assembly on page 8) /4-20 Free Spin Wash Nut x 3/4 x.197 Magnet /32 Pop Rivet Rotational Sensor Magnetic Reed Switch Assembly * Specify key number when ordering.

13 Lint Door Assembly White Lint Door Assembly Complete (includes illus. no. 1, 2 and 4 through 6) Beige Lint Door Assembly Complete (includes illus. no. 1, 2 and 4 through 6) Bisque Lint Door Assembly Complete (includes illus. no. 1, 2 and 4 through 6) Lint Door Top Black Trim (29-5/8 length) DP Control Door Lock (keyed XX4451) Key Only (keyed XX4451) #10-32 x 1/4 Phillips Pan Head Screw /4 x 3/8 Neoprene Sponge Tape (sold by the foot) Black Kick Trim

14 12 Lint Coop Assembly AD-435 Wire Clip/Lint Coop Assembly W/Felt Lint Coop Baffle #10 x 16 x 1/2 Hex Washer Srews Pop Rivets Felt Seal Retainer Lint Basket Seal Pop Rivet

15 Lint Drawer (Basket) II Assembly White Locking Lint Drawer (Basket) II Assembly Complete less Lock (includes illus. no. 1 and 2) Beige Locking Lint Drawer (Basket) II Assembly Complete less Lock (includes illus. no. 1 and 2) Bisque Locking Lint Drawer (Basket) II Assembly Complete less Lock (includes illus. no. 1 and 2) /8 x 3/8 Neoprene Sponge Tape (sold by the foot) /4 x 3/8 Neoprene Sponge Tape (sold by the foot) Temperature Sensor Bracket (refer to Temperature Sensor Bracket Assembly on page 16) Lint Drawer (basket) Switch (refer to Lint Drawer Switch Assembly on page 14) Lint Drawer Lock Assembly (keyed to number XX4451) Key ONLY (key number XX4451) Cam ONLY... Not Illustrated

16 14 Lint Drawer (Basket) Switch Assembly Top Lint Drawer Switch Harness ONLY Bottom Lint Drawer Switch Harness ONLY Top Lint Door Switch Assembly Bottom Lint Door Switch Assembly

17 Basket (Tumbler)/Support Assemblies Basket (Tumbler)/Support Assembly Complete (includes illus. no. 1 through 11) * 1 Basket (Tumbler) without Felt Collar Short Tapered Rib Tall Tapered Rib /16 x 3/8 Socket Head Screw /8-16 x 31 Tie Rod /8 Flat Washer #10-16 x 1/2 TORX Head Crimptite Screw TORX Hand Driver (for removal of TORX Head Screw) Basket (Tumbler) Support ONLY /8-16 Hex Nut /8 Lock Washer /8 Flat Washer Felt Collar ONLY #847 Adhesive for Felt Collar (5 oz tube) * Felt collar is not included and must be ordered separately.

18 16 Temperature Sensor Bracket Assembly Temperature Sensor Bracket (II) Complete (includes illus. no. 1 through 7) Temperature Sensor Bracket ONLY #6 Star Washers #6-32 x 1/4 Round Head Machine Screw º Thermostat ONLY #6-32 Hex Nut Thermister Sensor Bracket Harness (top)... Not Illustrated Sensor Bracket Harness (bottom)... Not Illustrated

19 Tumbler Bearing Assembly ADG-435PDB Tumbler Support Complete (includes Illustration numbers 1-13) ADG-435 PDB Tumbler Support only /8 Pillow Block Bearing /8 Flat Washer /8 Lock Washer /8-16 Hex Nut /8-16 x 1 1/2 Hex Nut /16-18 Hex Nut /16 Lock Washer /16 Flat Washer /16-18 x 1-1/2 Hex Bolt /16-18 x 1/2 Allen Set Srew /16-18 x 3 Hex Bolt /16-18 x 4 Hex Bolt /8 Flange Bearing /8 Lock Washer /8 Hex Nut /16-18 x 1 Allen Set Screw /4 x 1/4 x 7/8 Key L-650 V-Belt Pulley

20 18 Motor Mount Assembly

21 Motor Mount Assembly 19 Illus No. Part No. Qty. Description L-410 V-Belt (motor to idler) /2 x 2 1/4 Motor Pulley Pin Socket Connector or 8 Socket Terminal ONLY Pin/Socket Extraction Tool /16 x 3/4 Hex Head Machine Bolt /16 Lock Washer /16 Flat Washer /2 HP 120/230v 60 Hz Motor with Plug /4 x 1/2 Phillips Round Head Machine Screw Idler Support Bracket /4 Lock Washer /4 Hex Nut /4 x 1 Self Clinching Stud /8 x 1-1/2 Washer /4 Free Spin Nut /2 Nylon Clamp /4 Hex Nut /16 x 3/4 Hex Head Machine Bolt /16 Lock Washer /16 Flat Washer /2 HP Motor Mount ONLY /2 HP 120/230v Motor Mount Assembly (includes illus. no. 2, 5 through 8 and 18 through 28) Noise Suppressor Tape (sold by the foot) /16 Tinnerman Nut /2 Flat Washer /2 Impeller with 1/2 Bore /8 x 1/8 x 1-1/2 Key /2 Flat Washer /2 Left Hand Jam Nut

22 20 Direct Spark Ignition (DSI) Gas Valve Train Assembly /2 x 1/2 Street Elbow Pin Terminal ONLY Pin/Socket Extraction Tool Pin Connector ONLY /2 Union Shut Off With Tail Piece Gas Valve Pipe Bracket #8-10 x 7/16 Phillips Pan Head TEK Screw Bulkhead Fitting /4 Aluminum Tubing (sold by the foot) º Line Adapter

23 21 Direct Spark Ignition (DSI) Gas Valve Train Assembly (continued) /2 24 VAC DSI Redundant (natural gas) Gas Valve /2 24 VAC L.P. (liquid propane) Conversion Kit Socket Terminal ONLY Pin Socket Connector ONLY Gas Valve Train Wiring (Top Gas Train) Gas Valve Train Wiring (Bottom Gas Train) DSI (Direct Spark Ignition) Module ONLY DSI (Direct Spark Ignition) Module Mounting Bracket ONLY #6 Star Washer #6-32 Pal Nut #8-32 x 1/2 Self Clinching Stud #8 Star Washer #8-32 Hex Nut Notched Pipe Bracket /8 Clear Flexite /16 Nylon Clamp Single-Port Manifold ONLY Pipe Bracket /8 Nylon Clamp * 1 Natural Gas Valve Train Assembly Complete Less Orifice (includes illus. no. 1 through 3 and 5 through 36) Gas Valve Train Slide ONLY #8-32 x 1/2 Self-Clinching Stud #8 Star Washer Burner Tube Bracket #8-32 Pal Nut DSI (Direct Spark Ignition) Up-Shot Burner Tube ONLY Spark Electrode #6 x 3/8 Phillips Flame Sensor Open/Closed Bushing 37** #23 Burner Orifice (Natural Gas) ONLY #42 Burner Orifice (Liquid Propane) ONLY DSI (Direct Spark Ignition) L.P. Conversion Kit * Orifices are not included and must be ordered separately ** Consult factory for elevations over 2,000 feet.

24 22 Burner Box/Gas Piping Assemblies

25 Burner Box/Gas Piping Assemblies #8-18 x 7/16 Phillips Pan Head TEK Screw Burner Box with Spreader Assembly #8-18 x 7/16 Phillips Pan Head TEK Screw Top Pipe Support Bracket #10 x 1/2 Hex Head TEK Screw /2 Union Shut Off with Tailpiece /2 x 40 Long Pipe #10 x 1/2 Hex Head TEK Screw Pipe Bracket /2 Union Manifold Inlet #8-18 x 7/16 Phillips Pan Head TEK Screw Burner Box with Spreader #8-18 x 7/16 Phillips Pan Head TEK Screw /2 Union #10 x 1/2 Hex Head TEK Screw Pipe Bracket /2 x 40 Long Pipe /2 Union Shut Off with Tail Piece º Hi-Limit #10 x 1/2 Hex Head TEK Screw Burner Box Clean Out Cover #10-32 x 1/2 Hex Head TEK Screw Spreader Assembly ONLY

26 24 Sail Switch Assembly Sail Switch Damper (embossed) Sail Switch Rod and Damper Assembly (includes illus. no. 1 through 3) Sail Switch Rod /8 Push-on Fastener #4 x 3/4 Pan Head A Machine Screw Sail Switch ONLY Sail Switch Bracket Assembly (includes illus. no. 4 through 7) Sail Switch Bracket Twin Speed Nut #6-32 x 1/2 Phillips Round Head Machine Screw #6 Star Washer #6-32 Hex Nut

27 25 Idler Bearing Assembly L-400 V-belt (idler to motor) x 2-1/2 Key /16-18 x 5/16 Allen Set Screw L-660 V-Belt (idler to basket [tumbler]) /16 x 3/16 x 1-3/8 Key /8 x 3/4 Idler Shaft /4-20 x 2-1/4 Carriage Bolt /8 Flange Bearing /4 Lock Washer /4-20 Hex Nut /8-16 x 1 Hex Head Machine Bolt /8 Lock Washer /8 Flat Washer /16-18 Standard Square Nut /16-18 Hex Nut Idler Bearing Assembly Complete (includes illus. no. 6 through 17) Idler Bearing Mounting Bracket ONLY /16-18 x 3 Hex Head Machine Bolt

28 Exhaust Ducting Assembly 26 Illus No. Part No. Qty. Description Wye Branch Round x 45º Elbow Round x 7 Oval Straight Boot /2 Long x 7 Oval Duct Oval x 45º Elbow Round x 7 Oval Straight Boot Round x 45º Elbow Aluminum Duct Tape (sold by the foot) Exhaust Brace Split Lock Washer /4 x 20 x 1/2 Bolts /4 x 20 Hex Nut

29 27 Back Guard Assembly Illus No. Part No. Qty. Description Back Guard Assembly #8-18 x 7/16 Phillips Pan Head TEK Screw Plate Cover (Top Electric Box) #8-18 x 7/16 Phillips Pan Head TEK Screw Top Pipe Support Bracket #10 x 1/2 Hex Head TEK Screw Leveling Leg

30 MAYTAG /04/99-25

D-3030 Parts Manual. J.L.A. Meadowcroft Lane, Halifax Road Ripponden W. Yorkshire, England HX6 4AJ Telephone: / Fax:

D-3030 Parts Manual. J.L.A. Meadowcroft Lane, Halifax Road Ripponden W. Yorkshire, England HX6 4AJ Telephone: / Fax: D-3030 Parts Manual J.L.A. Meadowcroft Lane, Halifax Road Ripponden W. Yorkshire, England HX6 4AJ Telephone: 1 422 822282 / Fax: 1 422 824390 091802JCARRITA/wmarelli ADC Part No. 450215 Retain This Manual