Clutch Kit Install Guide

Size: px
Start display at page:

Download "Clutch Kit Install Guide"

Transcription

1 Jack up and support the car on jack stands Remove the exhaust system (some models) Remove the driveshaft (rear wheel drive) Remove CV axle (front wheel drive) Manual transmission removal Clutch Kit Install Guide Let's Get Started! This will show you a typical clutch replacement and help you with the little nuances which will give you the best result. A clutch is constructed using asbestos so use a mask before removing the clutch disc. Gloves and protective eyewear are a good idea as well. There will be several subsequent guides that will need to be performed before the clutch can be replaced which are listed below: 1. Remove the Clutch: Once the above jobs have been done it's time to inspect and remove the clutch pressure plate. The picture below shows what it looks like once the transmission has been removed which exposes the clutch assembly that is mounted onto the flywheel at the rear of the engine. Again this part deals with asbestos so an air mask is recommended. The pressure plate will be held onto the flywheel by 10 12mm, 13mm or 14mm bolts in most cases. When you start to undo the bolts the flywheel will want to move and turn the engine over so you will need to break the bolts loose by applying leverage inward or outward from the flywheel. An impact gun also works well for this. Do not remove all of the bolts at once because the pressure plate traps the clutch disc which can be heavy and can fall causing an injury. As the last bolts are undone have an extra hand to control both the pressure plate and disc. The pressure plate will start to move outward from the flywheel as the the bolts are undone.

2 While the last bolts are being removed keep your hands on the disc and plate to control these parts. Support the disc while using a finger which is a good method of holding the disc onto the pressure plate. Once the bolts have been removed the pressure plate may still be held onto the flywheel with 3 or more alignment dowels. Gently work the pressure plate from the flywheel using a standard screwdriver until free. 2. Inspect Clutch Wear: The clutch disc is the part that wears down much like a brake pad, in fact the clutch disc has brake pad material on either side of it which is held on by rivets. When this lining wears it allows the rivets to contact the flywheel or pressure plate which causes the clutch to slip. 3. Check the Flywheel: The clutch mating surface of the flywheel will now be exposed. You are looking for extreme heat checks, hot spots and cracks which are a sign the clutch was slipping for a long period of time and will warrant the flywheel's replacement. The flywheel below is what a the typical wear pattern looks like during a clutch replacement and can be re-machined which must be done anytime you are servicing the clutch. If this step is skipped when the new clutch is installed you will have a good chance that it will chatter when the clutch pedal is released and the job will need to be redone.

3 4. Replace Pilot Bearing: On rear wheel drive and some front wheel drive cars the clutch will have a pilot bearing which is designed to support the input shaft of the stick shift transmission. If this bearing locks up or becomes worn out it allows the input shaft to wonder and will cause the clutch to not disengage. The pilot bearing should be replaced during the clutch service. 5. Match the New Clutch: Place the old clutch next to the new clutch on a table. Check the diameter of the disc and the surface area of the clutch material. Also look at the pressure plate height with one next to the other, they should be fairly close. This will present a problem if they are way off in the operation of the clutch, either not releasing or engaging. Before re-installing the clutch disc back onto the flywheel fit the disc over the input shaft of the transmission. It should slide onto the shaft with little resistance. This is too help avoid a problem when reinstalling the transmission. 6. Install the New Clutch: This part is very important! The clutch disc can go onto the pressure plate in either direction but only one direction is correct. The part of the disc that is protruding outward must go toward the pressure plate or the clutch will not release so it's important to install the disc in the proper direction. Also it is important to use brake cleaner to remove grease and dirt from the flywheel and pressure plate clutch contact surfaces before installation.

4 Gently install the new clutch disc and pressure plate onto the alignment dowels of the newly resurfaced flywheel while installing the mounting bolts by hand. Leave the pressure plate bolts a little lose so the pressure plate can move around. This is so you can insert the clutch alignment tool included in the clutch kit. Locate the clutch alignment tool included in the clutch replacement kit. This is needed to line up the clutch disc to the pilot bearing so the transmission can be easily reinstalled. With the clutch disc loose position and install the clutch alignment tool into the clutch disc and pilot bearing. Slightly tighten the bolts further to hold the disc in place and move the tool in a circular motion. It will give some resistance in all directions and you want to find a good center point. This means the disc is in the middle of the pressure plate. Tighten the pressure plate evenly and slowly in a star pattern using a ratchet. Do not tighten any one bolt all at once and do not use air tools. This will bend the pressure plate and cause the clutch not to disengage. Work your way around the pressure plate slowly tightening several times until completely tight. You will notice the fingers of the pressure plate traveling inward as you tighten the bolts. You want this progression to be as even as possible. and 30 foot pounds. Again the flywheel will try and turn the engine over so tighten inward. If this step is not done correctly the clutch will not release properly which can cause hard shifting. Finish tightening the bolts to factory torque specifications which is usually between 25

5 Remove the clutch alignment tool and recheck all of the mounting bolts. 7. Replace Throughout Bearing: The throwout bearing is designed to push the fingers of the pressure plate inward to disengage the clutch. When these fingers are out or with no pressure on them the clutch is engaged. When replacing the clutch assembly it is highly advised to replace the throwout bearing because it has a high failure rate. Some throwout bearings are attached to the clutch slave cylinder which should be replaced as a unit. 8. Clutch Break-in and Adjustment: Once the transmission has been reinstalled slowly pump the clutch pedal until normal pedal operation is present. Watch and add clutch fluid (brake fluid) in the process. After the repair start the engine and push the clutch pedal down completely while shifting the transmission through its gears. It's normal for this operation to be a little rough while the clutch is in it's "break in" period. Normal shifting characteristics should return after a few miles.

1994 Mazda MX-5 Miata. CLUTCH 1994 Clutch

1994 Mazda MX-5 Miata. CLUTCH 1994 Clutch CLUTCH 1994 Clutch DESCRIPTION Miata uses a hydraulically operated clutch. HYDRAULIC SYSTEM BLEEDING 1. Remove bleeder screw cap, located at clutch release cylinder. Install vinyl hose onto bleeder screw.

More information

Self-Adjust Clutch Installation Guide

Self-Adjust Clutch Installation Guide Self-Adjust Clutch Installation Guide 0 STOP! READ CAREFULLY BEFORE INSTALLING CLUTCH This clutch must be installed by a qualified installer. Improper installation or failure to replace or resurface the

More information

Clutch Installation Guide

Clutch Installation Guide Clutch Installation Guide 0 STOP! READ CAREFULLY BEFORE INSTALLING CLUTCH This clutch must be installed by a qualified installer. Improper installation or failure to replace or resurface the flywheel,

More information

Troubleshooting. Pull Type Clutches - Poor Release

Troubleshooting. Pull Type Clutches - Poor Release Troubleshooting Pull Type Clutches - Poor Release Complaint Possible Causes Corrective Action Poor Release Intermediate plate sticking on drive lugs due to cocked drive pins (AS and EP 1402 only) (see

More information

Hawk Brake Pads ( Mustang GT/V6 Rear Pair)

Hawk Brake Pads ( Mustang GT/V6 Rear Pair) Hawk Brake Pads (1994-2004 Mustang GT/V6 Rear Pair) The below installation instructions work for the following products: Hawk HPS Brake Pads (1994-2004 Mustang GT/V6 Rear Pair) Hawk Performance Ceramic

More information

Tech Note Truck 14 & 15.5 Twin Plate Cast Iron Type Installation Guidelines

Tech Note Truck 14 & 15.5 Twin Plate Cast Iron Type Installation Guidelines 1. (14 & 15.5 ) Check condition of the flywheel. Grind to resurface or replace flywheel. Surface MUST BE machined or premature clutch failure can occur. Flywheel depth must be 2.938 (74.62mm) for 14 (350mm)

More information

Clutch Installation Guidelines Follow Service Manual Instructions For Step-By- Step Procedures

Clutch Installation Guidelines Follow Service Manual Instructions For Step-By- Step Procedures 9700063 Revision 12/20/10 Clutch Installation Guidelines Follow Service Manual Instructions For Step-By- Step Procedures FAILURE TO FOLLOW PROPER INSTALLATION OR BREAK-IN PROCEDURES WILL VOID ANY WARRANTY

More information

Clutches for Automobiles and Light Trucks

Clutches for Automobiles and Light Trucks Clutches for Automobiles and Light Trucks What does the Clutch do? Connects the engine torque to transmission when ENGAGED Unhooks engine from transmission when DISENGAGED Where is the driver s foot when

More information

DRAGON CLAW SHELBY 26 SPLINE

DRAGON CLAW SHELBY 26 SPLINE DRAGON CLAW 13-14 5.4 SHELBY 26 SPLINE *This Kit Requires a Min. 1 ⅝ in. Working Input Shaft Splines. *Professional Installation recommended *Power/Air tools NOT advised 1. Remove transmission assembly

More information

1992 Clutch. Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT

1992 Clutch. Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT Article Text ARTICLE BEGINNING 1992 Clutch Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT DESCRIPTION All clutches are single disc type. Pressure plate assembly uses a diaphragm spring to engage

More information

CLUTCH 6-1 CLUTCH CONTENTS

CLUTCH 6-1 CLUTCH CONTENTS TJ CLUTCH 6-1 CLUTCH CONTENTS page GENERAL INFORMATION CLUTCH COMPONENTS... 1 INSTALLATION METHODS AND PARTS USAGE... 1 DESCRIPTION AND OPERATION CLUTCH OPERATION... 1 DIAGNOSIS AND TESTING DIAGNOSTIC

More information

CROWERGLIDE AUTOMATIC CLUTCH Instruction Manual

CROWERGLIDE AUTOMATIC CLUTCH Instruction Manual CROWERGLIDE AUTOMATIC CLUTCH Instruction Manual Crower Cams & Equipment Co., Inc 6180 Business Center Court San Diego, CA. 92154 Phone: 619.661.6477 ext. 148 Fax: 619.690.7846 www.crower.com TABLE OF CONTENTS

More information

9000 Clutch Replacement By Jack Ashcraft

9000 Clutch Replacement By Jack Ashcraft 9000 Clutch Replacement By Jack Ashcraft The most usual reason for clutch (and associated parts) replacement in a Saab is clutch slippage. The clutches for the 9000 are very strong and usually will withstand

More information

CLUTCH COMPONENT LOCATION INDEX

CLUTCH COMPONENT LOCATION INDEX 2005 TRANSMISSION Clutch - MX-5 Miata CLUTCH COMPONENT LOCATION INDEX Fig. 1: Identifying Clutch Components GENERAL PROCEDURES (CLUTCH) PRECAUTION Clutch pipe If any clutch pipe has been disconnected anytime

More information

CL - Clutch Replacement

CL - Clutch Replacement 2003 3.2CL - Clutch Replacement Special Tools Required Pressure plate compressor 07AAE-P8EA000 Clutch alignment shaft 07AAF-P8EA000 Pressure plate compressor adapter 07AAK-P8EA000 Ring gear holder 07LAB-PV00100

More information

De clunking your MGB rear axle. By Stuart Clarke

De clunking your MGB rear axle. By Stuart Clarke De clunking your MGB rear axle By Stuart Clarke Do you have that annoying clunking noise when accelerating or decelerating, or even when you lift off to change gear, well it s possible to resolve the issue

More information

The Driveshaft Shop One Piece Aluminum Driveshaft Install for GT/BOSS

The Driveshaft Shop One Piece Aluminum Driveshaft Install for GT/BOSS The Driveshaft Shop One Piece Aluminum Driveshaft Install for 2011-14 GT/BOSS Tools and Equipment needed: Install time: approximately 2-3 hours Ratcheting socket wrench socket extensions 1/2 drive breaker

More information

CLUTCH Toyota Celica DESCRIPTION ADJUSTMENTS CLUTCH PEDAL HEIGHT Clutch. Celica

CLUTCH Toyota Celica DESCRIPTION ADJUSTMENTS CLUTCH PEDAL HEIGHT Clutch. Celica CLUTCH 1993 Toyota Celica 1993 Clutch Celica DESCRIPTION The single, dry disc type clutch uses a hydraulically operated master cylinder and a release cylinder mounted on clutch housing. Clutch release

More information

This file is available for free download at

This file is available for free download at This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing

More information

DRAGON CLAW PRE 86 BIG BLOCK CHEVY 10 SPLINE

DRAGON CLAW PRE 86 BIG BLOCK CHEVY 10 SPLINE DRAGON CLAW PRE 86 BIG BLOCK CHEVY 10 SPLINE *This Kit Requires a Min. 1 ⅝ in. Working Input Shaft Splines. *Professional Installation recommended *Power/Air tools NOT advised 1. Inspect input shaft splines

More information

AUTOMATIC CLUTCH Models

AUTOMATIC CLUTCH Models AUTOMATIC CLUTCH 1940 Models Source of this material is from 1940 Series, Issue 4, January 1940 Hudson Service Magazine AUTOMATIC CLUTCH 1940 MODELS The automatic clutch installation and adjustment procedure

More information

Figure 1 Factory G50 update and old Shift Fork Shaft

Figure 1 Factory G50 update and old Shift Fork Shaft 911 Clutch Job So you have one of the best 911s there is, a 87-89 G50 Porsche. However, after many years of service, it is time for a clutch. Maybe, the rubber clutch disc has failed, or the clutch is

More information

CONCEPT 10.5 DUAL DISC INSTALLATION INSTRUCTIONS

CONCEPT 10.5 DUAL DISC INSTALLATION INSTRUCTIONS CONCEPT 10.5 DUAL DISC INSTALLATION INSTRUCTIONS Congratulations on your purchase of the RAM Concept 10.5 Dual disc clutch system. Please completely read and carefully follow the setup instructions, and

More information

page CLUTCH DIAGNOSIS 2

page CLUTCH DIAGNOSIS 2 6-1 CONTENTS page DIAGNOSIS 2 COMPONENTS MECHANICAL COMPONENTS The clutch mechanism in A D models with a gas or diesel engine consists of a single, dry-type clutch disc and a diaphragm style clutch cover.

More information

Mitsubishi Lancer Oil Change (2.0L I4 DOHC)

Mitsubishi Lancer Oil Change (2.0L I4 DOHC) 2002-2007 Mitsubishi Lancer Oil Change (2.0L I4 DOHC) Change the oil in your '02-'07 Mitsubishi Lancer, with 2.0L I4 DOHC engine, to improve engine performance and longevity. Written By: Phillip Takahashi

More information

Tools needed: Here is a pic of the shift kit I used. It is a Transgo brand and as you can see, it just a bag full of springs and one valve.

Tools needed: Here is a pic of the shift kit I used. It is a Transgo brand and as you can see, it just a bag full of springs and one valve. Before installing a shift kit, be sure the transmission is in good operating order. If your transmission is making noises, slipping, shifting bad or the fluid looks brown or smells burnt, take the transmission

More information

3.2 quarts Pennzoil Synchromesh transmission fluid (optional, but recommended)

3.2 quarts Pennzoil Synchromesh transmission fluid (optional, but recommended) List of tools and materials: Floor jack, jack stands, and car ramps 3/8 drive ratchet, with long and medium extensions 3/8 drive swivel 3/8 breaker bar / cheater bar 7/8 combo wrench 8mm, 10mm, 13mm, 15mm,

More information

Transmission Overhaul Procedures-Bench Service

Transmission Overhaul Procedures-Bench Service How to Assemble the Lower Reverse Idler Gear Assembly Special Instructions In 1996 Eaton changed the reverse idler system design. In the nut design, the reverse idler bearing was lubricated through a hole

More information

Service Manual. LL30002 Rev. 7/03. HEAVY DUTY PUSH/PULL TYPE CLUTCHES

Service Manual. LL30002 Rev. 7/03.  HEAVY DUTY PUSH/PULL TYPE CLUTCHES Service Manual LL30002 Rev. 7/03 HEAVY DUTY PUSH/PULL TYPE CLUTCHES www.haldex.com Table of Contents Section One - Push Type Clutches Clutch Assembly Cutaway Detail............................1 Clutch

More information

SACHS Clutches The Intelligent Choice for the Long Haul

SACHS Clutches The Intelligent Choice for the Long Haul SACHS Clutches The Intelligent Choice for the Long Haul Twin XTend Clutch Installation Objectives: Identification Operation Tools Installation Troubleshooting Identification 15.5 Self Adjusting Clutch

More information

INSTALLATION INSTRUCTIONS South Highway 11 Westminster, SC Toll Free (888) (864) FAX (864)

INSTALLATION INSTRUCTIONS South Highway 11 Westminster, SC Toll Free (888) (864) FAX (864) These instructions apply to the servicing of the Lift Technologies MaxiMizer Integral Sideshifters Cylinder Head. WARNING! Unless the steps in the following Installation Instructions are properly followed

More information

Honda Civic Oil Change

Honda Civic Oil Change 1988-1991 Honda Civic Oil Change Change the oil in your '88-'91 Honda Civic to improve engine performance and longevity. Written By: Phillip Takahashi ifixit CC BY-NC-SA www.ifixit.com Page 1 of 13 INTRODUCTION

More information

Honda CRV Oil Change

Honda CRV Oil Change 1995-2001 Honda CRV Oil Change Change the oil in your '95-'01 Honda CRV to improve engine performance and longevity. Written By: Phillip Takahashi ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION

More information

Replace clutch and flywheel * (Volkswagen Sharan 2010-Present)

Replace clutch and flywheel * (Volkswagen Sharan 2010-Present) Replace clutch and flywheel * (Volkswagen Sharan 2010-Present) *Caution! This instructions are created by random users and must be used as a reference only! Please, take all safety precautions, and if

More information

WARNING: Only perform this installation if you are experienced, fully equipped mechanic.

WARNING: Only perform this installation if you are experienced, fully equipped mechanic. DYNATRAC V3.2 2005-Present Ford Super Duty 250/350-4x4, Front Axle, Free Spin Conversion Kit Some of the less common tools, which will be required: 6 point Spanner socket (OTC #7090-A or equivalent). These

More information

DYNATRAC PRODUCTS V5.3

DYNATRAC PRODUCTS V5.3 DYNATRAC PRODUCTS V5.3 2000-2008 Dodge Hub Kit Stage 1 4x4, Front Axle Free Spin Conversion Kit Note: This Kit is not Approved for 2007 & up 3500 Cab and Chassis Trucks Due to a Larger U-Joint (If U-Joint

More information

INSTRUCTION MANUAL INSTALLING NEW GREASE IN UT SERIES PNEUMATIC ACTUATOR

INSTRUCTION MANUAL INSTALLING NEW GREASE IN UT SERIES PNEUMATIC ACTUATOR INSTRUCTION MANUAL INSTALLING NEW GREASE IN UT SERIES PNEUMATIC ACTUATOR This instruction manual explains the steps required to degrease and install new grease into the Max-Air UT series pneumatic actuator.

More information

Installation Instructions

Installation Instructions Installation Instructions Rear Disc Brake Conversion Kit Item # RC4001, RC4001X Applications: Mopar 7.25, 8.25, 9.25 Axles Thank you for choosing Leed Brakes for your automotive product needs. Before you

More information

CLUTCH 6-1 CLUTCH CONTENTS

CLUTCH 6-1 CLUTCH CONTENTS Z CLUTCH 6-1 CLUTCH CONTENTS page page CLUTCH DIAGNOSIS... 2 CLUTCH SERVICE... 9 CLUTCH COMPONENTS MECHANICAL COMPONENTS The clutch mechanism in Grand Cherokee models with manual transmission consists

More information

Installation Instructions

Installation Instructions Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to

More information

Ford 8, 9 Small Bearing Installation Instructions Rear Disc Conversion

Ford 8, 9 Small Bearing Installation Instructions Rear Disc Conversion Ford 8, 9 Small Bearing Installation Instructions Rear Disc Conversion This kit is for Ford 9 rear axles with the small (2.835 ) style bearing and Ford 8 rear ends. This kit is designed to work with axles

More information

MANUAL TRANSMISSION SERVICE

MANUAL TRANSMISSION SERVICE MANUAL TRANSMISSION SERVICE Introduction Internal combustion engines develop very little torque or power at low rpm. This is especially obvious when you try to start out in direct drive, 4th gear in a

More information

South Bend Duramax DD

South Bend Duramax DD South Bend Duramax DD Installation Instructions Torque specifications: Flywheel to crank 140-150 ft. lbs. Pressure plate to flywheel is 45 ft. lbs. Unbolt pressure plate from flywheel in a star pattern

More information

CLUTCH 6-1 CLUTCH TABLE OF CONTENTS

CLUTCH 6-1 CLUTCH TABLE OF CONTENTS PL CLUTCH 6-1 CLUTCH TABLE OF CONTENTS page DESCRIPTION AND OPERATION MODULAR CLUTCH ASSEMBLY....1 CLUTCH CABLE...1 CLUTCH INTERLOCK/UPSTOP SWITCH....1 DIAGNOSIS AND TESTING CLUTCH SYSTEM DIAGNOSIS...2

More information

TCI Trans-Scat

TCI Trans-Scat Page 1 of 5 Return to Instruction Sheet index TCI 400000 Trans-Scat Turbo Hydramatic 400-1965-Up This kit will allow you to re-program your transmission valve body. This kit will give you firm positive

More information

Wheel Bearing Replacement Passat TDI

Wheel Bearing Replacement Passat TDI Rear Bearing/hub assembly replacement This is a fairly straight forward process. Pictures are not necessary for most of this procedure for a person with skills to do this repair. Anyone who thinks they

More information

Cylinder Installation Compression/Stripper, for Models, 22HF, 16HF, 1600 machines

Cylinder Installation Compression/Stripper, for Models, 22HF, 16HF, 1600 machines Knowledge Base Article Type: Instructions Cylinder Installation Compression/Stripper, for Models, 22HF, 16HF, 1600 machines Description: Instructions on How to properly install stripper beam and compression

More information

Dexter Never-Adjust Brake Install

Dexter Never-Adjust Brake Install Dexter Never-Adjust Brake Install Arctic Fox 2007 29-5T Warning: This involves lifting your trailer, working under and around it. If you do not have the correct equipment and knowledge for this, please

More information

List of parts needed below. Tools needed

List of parts needed below. Tools needed 1 BMW 645 Coolant leak repair (Cap with Seal Repair and Expanding Coolant Pipe Installation w Pics) By Michael R. Brown (Estimated time to complete the job is 6-8 hrs) List of parts needed below. BMW PART

More information

INSTALLATION GUIDE. Clutch Cable Actuated Models Manual Revision:

INSTALLATION GUIDE. Clutch Cable Actuated Models Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE Clutch Cable Actuated Models 191-800 Manual Revision: 061810 2002 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise,

More information

1. General GENERAL CL-2

1. General GENERAL CL-2 SYSTEM GENERAL 1. General The clutch is of a dry, single plate type with a diaphragm spring. The clutch is a push type clutch. When the pedal is depressed, the release bearing will press the center of

More information

CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL

CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL 2 Table of Contents Section 1: General Information Page Handle Assembly Instructions 4 Maintenance All Models 6 Oil Change Procedures All Models 9 Height Adjustment

More information

Mini Cooper Mini Cooper. Vehicle Type: Two-Door Hatchback. Windshield. AutoGlass Field Guide 53

Mini Cooper Mini Cooper. Vehicle Type: Two-Door Hatchback. Windshield. AutoGlass Field Guide 53 Vehicle Type: Two-Door Hatchback NAGS number:* FW02305GTY (Heat) (Rain Sensor) or FW02304GTY. Original-equipment-manufacturer part numbers are 51311505850 (Heat) (Rain Sensor), or 51311505875. FD21652-53

More information

Part No amatic 350

Part No amatic 350 Watch our installation video on YouTube Installation Instructions Shift Improver Kit Part No. 30262 1968-1981 TurboHy urbohydr drama amatic 350 B&M Racing and Performance Products 2002 Congratulations!

More information

TCI Trans-Scat

TCI Trans-Scat Page 1 of 5 Return to Instruction Sheet index TCI 350000 Trans-Scat Installation Instructions For TURBO HYDRAMATIC 350 This kit will allow you to reprogram your transmission to meet your driving needs

More information

Kysor On/Off Rear Air Fan Drive

Kysor On/Off Rear Air Fan Drive . Proper precautions must be taken to prevent personal injury from contact with moving parts, unintended engine start or other hazards present when working with powered equipment. Refer to the vehicle

More information

B&M / INTRODUCTION

B&M / INTRODUCTION INSTALLATION INSTRUCTIONS FOR B&M AUTOMATIC TRANSMISSIONS REPLACING GM TH350, TH400, and TH700R4 / 4L60 (not including 4L60E / electronic shift models) B&M part numbers: 102002-103005 - 107101-107104 107105-107106

More information

INSTALLATION GUIDE CRF150R Manual Revision:

INSTALLATION GUIDE CRF150R Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE CRF150R 191-810 Manual Revision: 032508 2002 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise, Idaho 83714 208-426-0659

More information

FORK FREE PISTON MODIFICATION 2011 HONDA CRF250R

FORK FREE PISTON MODIFICATION 2011 HONDA CRF250R 217 Lorain Place Los Gatos, California 95032 408.406.2089 www.smartperformanceinc.com www.spi-racing.com FORK FREE PISTON MODIFICATION 2011 HONDA CRF250R WHAT? All production versions of the 2011 HONDA

More information

Installing Rear Brake Pads on a WK Jeep

Installing Rear Brake Pads on a WK Jeep Installing Rear Brake Pads on a WK Jeep Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your rear brake pads. This is what I did after

More information

Advanced Auto Tech. ASE A 3 Test Preparation Clutch & Drive Line Service

Advanced Auto Tech. ASE A 3 Test Preparation Clutch & Drive Line Service Advanced Auto Tech ASE A 3 Test Preparation Clutch & Drive Line Service The clutch and the drive line both have their own unique symptoms and noises, separate from the transmissions used to change torque

More information

Return to Instruction Sheet index TCI Installation Instructions for Turbo Hydramatic 350C & 250C

Return to Instruction Sheet index TCI Installation Instructions for Turbo Hydramatic 350C & 250C Page 1 of 6 Return to Instruction Sheet index TCI 326300 Installation Instructions for Turbo Hydramatic 350C & 250C NOTE: This kit was not intended for installation in transmissions that are in poor general

More information

Borg & Beck Clutch Information

Borg & Beck Clutch Information Borg & Beck Clutch Information After the clutch is bolted to the flywheel, under no circumstance should the release lever, or the release lever plate if equipped, be pulled away from the flywheel against

More information

Motorcycle/ATV Lift. Max. Capacity: 1,500 lbs. Parts List

Motorcycle/ATV Lift. Max. Capacity: 1,500 lbs. Parts List SPX Corporation 655 Eisenhower Drive Owatonna, MN 55060-0995 USA Phone: (507) 55-7000 Tech. Serv.: (800) 533-627 Fax: (800) 955-89 Order Entry: (800) 533-627 Fax: (800) 283-8665 International Sales: (507)

More information

TH400 STREETFIGHTER SERIES VALVE BODY MANUAL/AUTO VALVE BODY INSTALLATION INSTRUCTIONS

TH400 STREETFIGHTER SERIES VALVE BODY MANUAL/AUTO VALVE BODY INSTALLATION INSTRUCTIONS 1 INSTRUCTIONS TH400 STREETFIGHTER SERIES VALVE BODY 1965-87 MANUAL/AUTO VALVE BODY INSTALLATION INSTRUCTIONS TCI 222400 TCI 222400 ALLOWS AUTOMATIC SHIFT FEATURES IN THE DRIVE POSITION Thank you for choosing

More information

Rear Parking Brake Cable (93 Cobra)

Rear Parking Brake Cable (93 Cobra) Rear Parking Brake Cable (93 Cobra) Materials in the box: Brake Cable Tools Needed: One jack and four jack stands. One socket wrench with a 12mm, 13mm ( ½ inch, 12 point DEEP WALL DO NOT FORGET THIS) and

More information

Saab 9-3 Krona Downpipe Installation Instructions. What's Included:

Saab 9-3 Krona Downpipe Installation Instructions. What's Included: www.kronaperformance.com 2003-2010 Saab 9-3 Krona Downpipe Installation Instructions What's Included: (1) 3 stainless downpipe (with or without catalyst) (1) 3-2.5 stainless downpipe adapter pipe (1) Turbo

More information

EZ LITE CRUISER. Service & Maintenance Manual

EZ LITE CRUISER. Service & Maintenance Manual EZ LITE CRUISER Service & Maintenance Manual Table Of Contents Introduction to the EZ Lite Cruiser 3 Identification of Components 4 Controller System Component Diagram 6 Controller System I/O Ports Detail

More information

1 M-3000-H4 F150 4X4 Lowering Kit

1 M-3000-H4 F150 4X4 Lowering Kit READ INSTRUCTIONS COMPLETELY THROUGH BEFORE STARTING. IT IS RECOMMENDED THAT INSTALLATION BE DONE BY A QUALIFIED MECHANIC. REPLACE ALL STOCK PARTS THAT ARE DAMAGED OR WORN. ALWAYS WEAR EYE PROTECTION.

More information

Module 1: Introduction to Drive Trains

Module 1: Introduction to Drive Trains Introduction ÂÂ Basic Components of a Drive Train Operation of a Drive Train Working Applications Types of Drives Types of Gears Formula for Calculating Gear Ratio Determining Gear Rotation Introduction

More information

www.clubsuprafrance.com CLUTCH 1996 Toyota Supra 1995-96 Clutch Supra DESCRIPTION The single, dry-type disc clutch uses a hydraulicallyoperated master cylinder with a clutch release cylinder mounted on

More information

GROUP 6 CLUTCH CONTENTS SPECIFICATIONS

GROUP 6 CLUTCH CONTENTS SPECIFICATIONS GROUP 6 CLUTCH CONTENTS Page CLUTCH 6-1 Specifications.... 1 Transmission Main Drive Pinion Pilot Bushing... 5 Special Tools. 1 Clutch Release Bearing 6 Torque Reference 1 Torque Shaft and Bearings...

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A126-2 1988-98 C1500 2WD 10" REAR DRUM Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read

More information

Clutch Diagnosis - Causes of Failure

Clutch Diagnosis - Causes of Failure Clutch Diagnosis - Causes of Failure Guide Tube wear, Spline wear, Mainshaft Bearing wear Worn Flywheel Bearing, ridged or heat damaged Flywheel surface Worn/siezed Release Arm pivots, friction lining

More information

Rear End Installation and Bearing Kit - 8.8in (86-12 V8; V6)

Rear End Installation and Bearing Kit - 8.8in (86-12 V8; V6) Rear End Installation and Bearing Kit - 8.8in (86-12 V8; 11-13 V6) Tools Required: Jack Stands 5 Floor Jack 2 Oil Pans 1 Wheel Blocks 2 Differential Oil 3 qts Friction Modifier 3 bottles Tube of Black

More information

Clutch System Troubleshooting Guide-Service Tips

Clutch System Troubleshooting Guide-Service Tips DESCRIPTION AND OPERATION Clutch System The purpose of the clutch is to connect and disconnect a manually operated transmission and the remainder of the powertrain system from the engine. This permits

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS DISC BRAKE CONVERSION KITS A120-4 & A120-5 1964-1/2-66 Ford & Mercury Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to

More information

DBK FULL-SIZE CHEVY DISC BRAKE conversion KIT

DBK FULL-SIZE CHEVY DISC BRAKE conversion KIT DBK5964 1959-1964 FULL-SIZE CHEVY DISC BRAKE conversion KIT impala, bel air, biscayne Installation Instructions does not fit 14" rims must ust 15" or larger for this kit to be installed correctly on your

More information

CLUTCH CONTENTS SERVICE DIAGNOSIS. (a) Worn or damaged disc assembly. (b) Grease or oil on disc facings. (c) Improperly adjusted cover assembly.

CLUTCH CONTENTS SERVICE DIAGNOSIS. (a) Worn or damaged disc assembly. (b) Grease or oil on disc facings. (c) Improperly adjusted cover assembly. CLUTCH CONTENTS -GROUP 6 Page CLUTCH HOUSING ALIGNMENT... 6 CLUTCH PEDAL FREE PLAY 1 CLUTCH RELEASE BEARING 5 CLUTCH RELEASE FORK... 5 CLUTCH SERVICING 2 PILOT BUSHING CRANKSHAFT TO TRANSMISSION DRIVE

More information

Clutch, servicing. Special tools, testers and auxiliary items required. Flywheel retainer Thrust pad 3062

Clutch, servicing. Special tools, testers and auxiliary items required. Flywheel retainer Thrust pad 3062 Page 1 of 10 30-36 Clutch, servicing Special tools, testers and auxiliary items required Flywheel retainer 10-201 Thrust pad 3062 Page 2 of 10 30-37 Centering mandrel 3176 Grease G 000 100 Notes: Observe

More information

Group 4 CONTENTS DATA AND SPECIFICATIONS

Group 4 CONTENTS DATA AND SPECIFICATIONS PARKING BRAKE 1 Group 4 PARKING BRAKE CONTENTS Paragraph Page Parking Brake 5 4 Disassembly Assembly Adjustment Parking Brake Cable 6 5 Removal Installation Service Diagnosis 1 2 DATA AND SPECIFICATIONS

More information

ATASA 5 th Study Guide Chapter 36 Pages Clutches 74 Points. Clutches. Be Certain to Read the Summary

ATASA 5 th Study Guide Chapter 36 Pages Clutches 74 Points. Clutches. Be Certain to Read the Summary ATASA 5 th Study Guide Chapter 36 Pages 1071 1091 74 Points Be Certain to Read the Summary 1. The provides a mechanical coupling between the engine s & the transmission s shaft. The clutch allows the engine

More information

How to install the Barnett clutch and the stronger Oil Pump Drive Gear

How to install the Barnett clutch and the stronger Oil Pump Drive Gear How to install the Barnett clutch and the stronger Oil Pump Drive Gear Written by WildFred I m from Germany so please excuse my English and the spelling. The following procedure is a combination of the

More information

This is the Unpacking Guide for the Optibike Pioneer Allroad electric bicycle. The Guide provides information required to remove the Allroad from the

This is the Unpacking Guide for the Optibike Pioneer Allroad electric bicycle. The Guide provides information required to remove the Allroad from the This is the Unpacking Guide for the Optibike Pioneer Allroad electric bicycle. The Guide provides information required to remove the Allroad from the box and assemble it. If you have not assembled a bicycle

More information

CLUTCH. Section IV DATA AND SPECIFICATIONS CHRYSLER SERVICE MANUAL. Page. Clutch Pedal Adjustment 74. Clutch Disassembly 77. Clutch Assembly 78

CLUTCH. Section IV DATA AND SPECIFICATIONS CHRYSLER SERVICE MANUAL. Page. Clutch Pedal Adjustment 74. Clutch Disassembly 77. Clutch Assembly 78 CLUTCH 73 Section IV CLUTCH Page Clutch Pedal Adjustment 74 Clutch Disassembly 77 Clutch Assembly 78 Service Diagnosis 81 DATA AND SPECIFICATIONS MODEL TYPE 1376 (Borg-Beck) Single Plate, Dry Disc FACINGS

More information

Конференция "Обменяемся опытом. Нива" NIVA-FAQ. undefined

Конференция Обменяемся опытом. Нива NIVA-FAQ. undefined NIVA-FAQ Gearbox removal By Volodjushka NOVELTIES FAQ THE SITEMAP SEARCH ON THE SITE Конференция "Обменяемся опытом. Нива" NIVA-FAQ undefined Works in the motor compartment Remove the battery negative

More information

LIFT-507 BMF Lift Kit E-Z-Go RXV Gas or Electric Installation Instructions

LIFT-507 BMF Lift Kit E-Z-Go RXV Gas or Electric Installation Instructions LIFT-507 BMF Lift Kit E-Z-Go RXV Gas or Electric Installation Instructions Contents of LIFT-507 E-Z-Go RXV BMF Lift Kit: a (1 ea.) BMF A-Arm Assembly b (1 ea.) Driver Side Shock Tower c (1 ea.) Passenger

More information

BMW Throttle Body Reconditioning. Reconditioning BMW 750il throttle assemblies./

BMW Throttle Body Reconditioning. Reconditioning BMW 750il throttle assemblies./ Reconditioning BMW 750il throttle assemblies./ My 1990 BMW 750il was not idling well, and I was starting to get "EML" errors on startup. The "EML" light would stay on when I started the car, and the engine

More information

TCI TRANS-SCAT

TCI TRANS-SCAT Page 1 of 9 Return to Instruction Sheet index TCI 360000 TRANS-SCAT Installation Instructions for FORD C-6 Transmissions TCI s TRANS-SCAT kit will allow you to calibrate the performance of your transmission.

More information

User Manual. Please read this user manual before use Edition

User Manual. Please read this user manual before use Edition User Manual Please read this user manual before use. 2015.7.9 Edition Information on how to use GT Roller Flex3 GT Roller Flex3 is a new type trainer that has unique structure and characters. Read this

More information

Installation Guide: Front Brake Pad

Installation Guide: Front Brake Pad Installation Guide: Front Brake Pad Ninety percent of the brake pad changes you make during the life of your vehicle will be to the front brakes because they do 60% to 70% of the braking. On most cars,

More information

Mopar 8 3/4 & 9 3/4 (Dana) Installation Instructions Rear Disc Conversion

Mopar 8 3/4 & 9 3/4 (Dana) Installation Instructions Rear Disc Conversion Mopar 8 3/4 & 9 3/4 (Dana) Installation Instructions Rear Disc Conversion This kit is for either Mopar 8 ¾ or Mopar 9 ¾ (Dana). This kit is designed to work with axles with either GM 5 x 4.75 Bolt Pattern

More information

2006 Hyundai Tiburon GT

2006 Hyundai Tiburon GT Fig. 5: Identifying Clutch Cover & Disc Component With Torque Specifications REMOVAL 1. Drain the clutch fluid and transaxle gear oil. 2. Remove the transaxle assembly. 3. Insert the special tool (09411-25000)

More information

INSTALLATION & USER S GUIDE

INSTALLATION & USER S GUIDE REKLUSE MOTOR SPORTS The Rekluse Core EXP Kit for Cable-Actuated Motorcycles INSTALLATION & USER S GUIDE Doc ID: 191-7706A Doc Rev: 062215 OVERVIEW This kit replaces the OEM core clutch components including

More information

Installation Instructions

Installation Instructions Instructions Created by an: Suzuki Samurai Replacement Clutch (SKU# STM-CC) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools and

More information

COLD AIR INTAKE INSTALLATION INSTRUCTIONS

COLD AIR INTAKE INSTALLATION INSTRUCTIONS COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0030 Fits: 2007-10 135i (E82, E88; with N54 engine) 2007-08 335i/xi (E90) 2007-10 335i (E92, E93; with N54 engine) Congratulations for being selective enough

More information

Brake Shoe: Service and Repair Removal Procedure

Brake Shoe: Service and Repair Removal Procedure 2000 Buick Century V6-3.1L VIN J Copyright 2013, ALLDATA 10.52 Page 1 Brake Shoe: Service and Repair Removal Procedure ^ Tools Required - J38400 Brake Shoe Spanner and Spring Remover Caution: Keep fingers

More information

Installation Notes: #86000-R Race Series +3.5 L/T Kit

Installation Notes: #86000-R Race Series +3.5 L/T Kit 159 North Maple St. Unit J, CORONA CA 92880 P. 951-737-9682 F. 951-737-9006 WWW.CHAOSFAB.COM Installation Notes: #86000-R Race Series +3.5 L/T Kit Factory manual is recommended for removal and re-installation

More information

1 Part Number: M-2300-Y Part Description: S550 Mustang-Shelby Brake Upgrade Kit Installation Instructions

1 Part Number: M-2300-Y Part Description: S550 Mustang-Shelby Brake Upgrade Kit Installation Instructions Please visit www.performanceparts.ford.com for the most current instruction and warranty information. PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT

More information

C3 Syncro Drive Proclimb 1100 Installation Instructions

C3 Syncro Drive Proclimb 1100 Installation Instructions Revision 4 Nov 8-2013 201A Old Town Road, Sicamous, BC. V0E 2V4 Ph 250-833 3538 Fax 888-716 5903 www.c3powersports.com Thank you for purchasing a ProClimb M, ProCross F & XF SyncroDrive Note: This modification

More information