Disassembly. 1 Pull off the QUIK-LOK cable from the machine.

Size: px
Start display at page:

Download "Disassembly. 1 Pull off the QUIK-LOK cable from the machine."

Transcription

1 Special Tools Require Important! Torx TX0 bit 0 0 Screwdriver Torx Forcing Discs 0 Before beginning the maintenance work, perform an initial check with a high voltage test according to VDE (see chapter Electrical and Mechanical Test Instructions). Before all repair work, pull the power plug from the socket! Disassembly Removing the QUIK-LOK cable Pull off the QUIK-LOK cable from the machine. Loosen the screw () and take apart the plug into two parts () and (). The screw () has a centrical pin (see enlargement). It can only be removed with a respective Torx screwdriver with a cantrical boring (A)! This Torx screwdriver is part of the service tool kit. It can also be ordered with order number 0. Pull down the cable entry sleeve () slightly. Loosen the screw () and disassemble the inner plug into three parts (), (), and (). Remove the contacts () with cables. A Removing the housing Remove the four screws () from the front part of the housing () and pull the housing off towards the front. In case of stiffness, tap the receiver with a plastic hammer for support! Loosen the six screws () and take apart the housing ().

2 Disassembling the gear Pull the complete gear assembly from the housing (A) and remove the following parts: washer () bearing () anvil () shaft assembly () bearing () planetary wheels () gear () planetary wheels (). Machines with /"-receiver: remove additional bearings () from the pins of the gear (). A Disassembling the housing Put the housing () on the press as shown in the illustration, and press out the bearing () with aid of a bushing (Ø =. mm) (). A suitable bushing is, for example, the driver of 00K/0K (). Remove two O-rings () from the bearing (). Ø.mm

3 Machines with /"-receiver To remove the pin () and the spring () from the anvil, please proceed as follows: Disassembling the anvil Bend a paper clip or a piece of wire as shown in illustration, so it will be shaped like a hook (. mm). Insert the hook into the opening in the anvil and turn it 0, such that the hook reaches under the spring. Pull the hook upwards until the pin disengages from the spring. Pull out the pin to the side and the spring upwards.. mm 0 Machines with /"-receiver Disassembling the anvil Bend open the ring () and remove it. Remove the O-ring (). Disassembling the anvil Fix the anvil () in a vice and pull out the needle bearing () with aid of an interior extractor. Remove the ball () from the anvil.

4 Removing the balls Put the shaft assembly () on the press and press it together until both balls () fall out. Machines with /"-receiver Disassembling the shaft assembly Remove the following parts from the shaft (): ram () bearing () washer () spring (). Machines with /"-receiver Disassembling the shaft assembly Remove the following parts from the shaft (): ram () bearing () washer () spring () two washers ().

5 Disassembling the gear case Remove the following parts from the gear case (): gear () gear () washer () O-ring (). Pull out both carbon brushes () upwards. Pull the armature () together with the gear case from the field. Remove the gasket () from the gear case (). Dispose of the gasket (), it can t be reused! Removing the armature Insert the armature () with the gear case () into the sleeve () ( inner Ø = mm) and put it on the press as shown in illustration. Press the armature from the gear case () with the plunger of the press (). 0

6 Removing the bearing Put the gear case () with the sleeve () ( inner Ø = mm) on the press and press out the bearing (). Pressing off the bearing Remove the rubber cap () from the bearing (). Put the armature () and the forcing discs on the press as shown in illustration, and press off the bearing () facing the collector.

7 Disconnecting the electric parts Remove the following parts from the housing halves: field () with field connector () switch () with set of wires () and capacitor () blade housing () carbon brush holders () and carbon brushes six rubber bungs (). Pull the field connector () from the field ().

8 Maintenance General Cleaning Check for wear Electrical tests It is recommended to regularly submit the tool to maintenance. Clean all parts with the exception of the electrical parts with cold cleaning agent. Caution! No cleaning agent should penetrate into the bearing. Clean the electrical parts with a dry brush. Check the disassembled parts for wear (visual inspection) and replace worn parts. Before reassembling, perform an electrical test on all relevant parts (see chapter Electrical and Mechanical Test Instructions). Lubrication Each time maintenance is performed, the machine is to be lubricates as stated in the lubrication plan. After the machine is fully disassembled, completely remove the old grease and replace with new grease. The grease must be applied to the machine as indicated in the lubrication plan. Lubrication chart: Fill res. cover with a total of 0 g grease type Z (Order No.: -0-). g g g g g g g g g g Torques Housing screws. Nm Gear case screws. Nm

9 Assembly Assembling the electric parts Insert three rubber bungs () into each one of the housing halves. Put the field connector () on the field () and insert them both into the housing half (). Mount the switch () with the set of wires () and the capacitor (). For detailed wiring diagram, see page 0. Insert the blade housing () into the lower part of the housing half (). Mount the carbon brushes in the brush holders () but do not yet insert them into the housing (). First insert the armature, then insert the brush holders () with the carbon brushes into the housing ().

10 0 Wiring diagram Detail choking coil insert into housing to carbon brush black wire from switch Detail field connection white wire from switch black wire from switch blue wire from switch blue wire from the lower carbon brush Switch bottom view blue blue black brown black black lead wire through domes lead wire between pin and housing ribs inser wire and into this relief white wire to field connector black wire to upper carbon brush black wire to lower carbon brush lead wire through domes black wire to field connector (connection ) brown mains cable blue mains cable black wire to field connector (connection ) blue wire to field connector (connection ) anti-interference capacitor

11 Mounting the bearing on the armature Press the bearing facing the collector () onto the armature shaft. Pull the rubber cap () over the bearing (). Mounting the bearing in the gear case Press the bearing () into the gear case () as far as it will go, using a press. Pressing on the gear case Press the gear case () onto the armature shaft ().

12 Inserting the armature Pull a new gasket () over the gear case (). Insert the gear case () together with the armature into the field () as far as it will go. Insert the carbon brushes () on both sides into the reliefs in the housing, next to the collector. Mount the following parts in the gear case (): O-ring () washer () gear () gear (). Machines with /"-receiver Assembling the shaft Mount the following parts on the shaft (): spring () washer () bearing () ram ().

13 Machines with /"-receiver Assembling the shaft Mount the following parts on the shaft (): two washers () spring () washer () bearing () ram (). Mounting the balls Put the shaft assembly () on the press and depress it against resilience (in direction of arrow) and insert both balls () into the grooves of the shaft. Slowly release the pressure. Mounting the anvil Insert the ball () into the anvil (). Press the needle bearing () into the anvil. Machines with /"-receiver Mounting the anvil First insert the pin (), then the spring () into the anvil (). The groove of the pin must be in the anvil! Depress the spring () with a hook (see page, illustration top), until the pin () engages.

14 Machines with /"-receiver Mounting the anvil Insert the O-ring () into the groove. Pull over the ring (). Mounting the housing Mount two O-rings () on the bearing (). Press the bearing () into the housing () with aid of a bushing (Ø =. mm) (). A suitable bushing is, for example, the driver of the machines 00K/0K (). 0 Assembling the gear Machines with /"-receiver: Mount three bearings () on the pins of the gear (). Mount the following parts on the gear shaft () and insert the assembly into the housing (A): bearing () planetary wheels () gear () planetary wheels () anvil () bearing () washer (). A

15 Mounting the housing Fix the housing halves () with six screws (). Put the complete front part of the gear case () on the machine, at the same time carefully insert the gear assembly into the machine and turn the square seat until the front part of the gear case () is flush with the motor housing. Fix the front part of the gear case () with four screws (). Insulating the mains cable Insulate the mains cable as shown in illustration. Meet the following measures: Insulating length of wires: approx. mm Wire length with insulation: approx. mm mm mm

16 Mounting the QUIK-LOK cable Producing a strain relief Insert the mains cable into the new crimping contacts () in accordance with regulations and make a correct crimp connection with aid of a crimping tool (see both illustrations of the crimp connection on the right). Only a correct crimp connection can meet all mechanical and electrical requirements! Insert the crimping contacts () with wires () into the sleeve. Insert the plug halves () and () into the sleeve () on both sides and fix them with the screw (). Provide mm wire for strain relief (see lower illustration)! correct crimp connection cross section: crimp barrel Insert the cable entry sleeve () and the assembled sleeve () into the plug (). Put together the two halves of the plug () and () and fasten them with the screw (). The screw () has a centrical pin (see enlargment). It can only be fastened with a Torx screwdriver with a respective centrical guide boring (A)! This Torx screwdriver is part of the service tool kit. It is also available as service bit Lfb (order number 0). A mm Test Run Electrical Test Test run the machine and pay attention to noises. Let the machine run-in. Perform an electrical test on the machine (see chapter Electrical and Mechanical Test Instructions).

SERVICE PARTS LIST. SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS M18 Sawzall STARTING SERIAL NO.

SERVICE PARTS LIST. SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS M18 Sawzall STARTING SERIAL NO. Pull both Brush Tubes (25) back before removing or installing the Armature (2) to prevent damage to the commutator. Brush Tube SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS

More information

TECHNICAL INFORMATION

TECHNICAL INFORMATION TECHNICAL INFORMATION Model No. Description CONCEPT AND MAIN APPLICATIONS Specification HR2800, HR2810, HR2811F HR2810T, HR2811FT Rotary Hammers 28mm (1-1/8") HR2800 series models have been developed as

More information

SERVICE PARTS LIST 1-1/8" ROTARY HAMMER MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON RD., BROOKFIELD, WI Drwg.

SERVICE PARTS LIST 1-1/8 ROTARY HAMMER MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON RD., BROOKFIELD, WI Drwg. 00 0 200 204 276 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS PAGE 1 OF 3 BULLETIN NO.

More information

TECHNICAL INFORMATION Model No. Description

TECHNICAL INFORMATION Model No. Description TECHNICAL INFORMATION Model No. Description CONCEPT AND MAIN APPLICATIONS Specification HR2450, HR2451, HR2452 24mm (15/16 " ) Rotary Hammer The above models are the advanced version of MAKITA's famous

More information

TECHNICAL INFORMATION

TECHNICAL INFORMATION TECHNICAL INFORMATION Model No. Description DP4010, DP4011 2-Speed Drill 13mm (1/2") L PRODUCT P 1/ 8 CONCEPT AND MAIN APPLICATIONS Models DP4010 and DP4011 have been developed as 13mm (1/2") Drill for

More information

Service Tools. Service and Repair Manual Model 900/950/990 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION ITEM PART NO.

Service Tools. Service and Repair Manual Model 900/950/990 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION ITEM PART NO. 12 1 3 2 4 5 8 10 6 7 9 11 14 24 12 13 17 22 29 18 23 25 19 26 15 20 27 21 16 22 33 37 38 32 31 36 30 34 35 40 41 42 43 ITEM PART NO. DESCRIPTION 1 9170 0231 30 LONG ALLEN KEY 2 9170 0737 20 3/32 PIN PUNCH

More information

TECHNICAL INFORMATION

TECHNICAL INFORMATION TECHNICAL INFORMATION PRODUCT P 1 / 15 Model No. Description HR2455 Rotary Hammer 24mm (15/16") L W CONCEPT AND MAIN APPLICATIONS Model HR2455 has been developed as a sister tool to Model HR2450, the Makita

More information

TECHNICAL INFORMATION

TECHNICAL INFORMATION TECHNICAL INFORMATION Model No. Description CONCEPT AND MAIN APPLICATIONS Specification GA4030, GA4530, GA5030 Angle Grinders 100mm (4"), 115mm (4-1/2"), 125mm (5") GA4030/ GA4530/ GA5030 are small diameter

More information

SERVICE PARTS LIST. 18 Volt Sawzall B58D BULLETIN NO CATALOG NO

SERVICE PARTS LIST. 18 Volt Sawzall B58D BULLETIN NO CATALOG NO Tab Square Groove CATALOG NO. 2620-20 SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 18 Volt Sawzall IMPORTANT Field (22) to be assembled with tapper to back and square groove

More information

SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS. M18 Sawzall

SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS. M18 Sawzall Pull both Brush Tubes (25) back before removing or installing the Armature (2) to prevent damage to the commutator. Brush Tube SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS

More information

SERVICE PARTS LIST. 18 Volt Sawzall STARTING SERIAL NO. B58B BULLETIN NO

SERVICE PARTS LIST. 18 Volt Sawzall STARTING SERIAL NO. B58B BULLETIN NO Tab Square Groove CATALOG NO. 2620-20 IMPORTANT Field (22) to be assembled with tapper to back and square groove to the top. Motor Cage (35) must be oriented with tab to the bottom. SERVICE PARTS LIST

More information

SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS. 18 Volt Sawzall STARTING SERIAL NO. See note on page 3.

SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS. 18 Volt Sawzall STARTING SERIAL NO. See note on page 3. Pull Brush Tubes () back before removing or installing the Armature (2) to protect commutator. SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 8 Volt Sawzall CATALOG NO. 2620-20

More information

TECHNICAL INFORMATION

TECHNICAL INFORMATION TECHNICAL INFORMATION Model No. Description GA5020C/GA6020C, GA5021C/GA6021C Angle Grinders 125mm (5") /150mm (6") L PRODUCT P 1/10 CONCEPT AND MAIN APPLICATIONS These four models have been developed as

More information

a. remove counterbalance valves, travel motors and travel drives

a. remove counterbalance valves, travel motors and travel drives * For further information, contact Caterpillar Service Technology Group. Start By: a. remove counterbalance valves, travel motors and travel drives 1. Remove the counterbalance valve. See, "Disassemble

More information

TECHNICAL INFORMATION

TECHNICAL INFORMATION TECHNICAL INFORMATION Models No. Description BHR202 Cordless Combination Hammer CONCEPT AND MAIN APPLICATIONS The subject model features 18V Li-ion Battery and 3 mode selection for ensuring an operator

More information

SERVICE PARTS LIST. M18 FUEL ONE KEY SAWZALL Reciprocating Saw H31A BULLETIN NO

SERVICE PARTS LIST. M18 FUEL ONE KEY SAWZALL Reciprocating Saw H31A BULLETIN NO 00 FIG. PART NO. DESCRIPTION OF PART NO. REQ. 1 45-12-0040 Gearcase Insulator 1 2 40-50-8805 Extension Spring 1 3 31-11-0105 Barrel Cam 1 4 34-60-3700 Retaining Ring 1 5 --------------- Front Cam 1 6 ---------------

More information

SERVICE PARTS LIST. SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS M18 FUEL SAWZALL Reciprocating Saw STARTING SERIAL NO.

SERVICE PARTS LIST. SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS M18 FUEL SAWZALL Reciprocating Saw STARTING SERIAL NO. 47(5x) 46 45 00 44 0 59 43 42 84 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). CATALOG NO. 2720-20 51 57 46 47 48 59 83 64 77 48 47(2x) 49(2x) 40 58 41 82 51 40

More information

SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS. 18 Volt Sawzall STARTING SERIAL NO. Spindle (38) to be assembled

SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS. 18 Volt Sawzall STARTING SERIAL NO. Spindle (38) to be assembled Pull Brush Tubes () back before removing or installing the Armature (21) to protect commutator. SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 18 Volt Sawzall CATALOG NO. 2620-20

More information

SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS METAL CUTTING SAW SERIAL NUMBER

SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS METAL CUTTING SAW SERIAL NUMBER 22-64-0437 SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS CATALOG NO. METAL CUTTING SAW 6370-20 SERIAL NUMBER A35C BULLETIN NO. 54-40-1627 REVISED BULLETIN DATE 54-40-1626 Sept.

More information

Service Handbook High-Pressure Washer Pump

Service Handbook High-Pressure Washer Pump Service Handbook High-Pressure Washer Pump 9.120-014.0 2 A. Water Inlet Filter C. Nozzle Insert 1. Remove filter with a screwdriver. 2. Clean filter with warm water and mild soap. 3. Reinstall filter.

More information

1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns

1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns STEERING COLUMN 1989 STEERING Jeep Steering Columns DESCRIPTION All models use collapsible steering columns. All columns have integral ignition switch and locking device. Optional tilt wheel is available

More information

Maintenance Information

Maintenance Information Form 16575334 Edition 1 April 2005 Electric Screwdrivers EL, EP and ET 34V DC Series Maintenance Information Save These Instructions WARNING Maintenance procedures have the potential for severe shock hazard

More information

Maintenance Information

Maintenance Information Form 04584058 Edition 1 November 2004 Air Impactool 2141P and 2141PSP Maintenance Information Save These Instructions Disassembly General Instructions 1. Do not disassemble the tool any further than necessary

More information

TECHNICAL INFORMATION

TECHNICAL INFORMATION TECHNICAL INFORMATION Model No. Description HR3200C, HR3210C, HR3210FCT Rotary Hammer 32mm (1-1/4") CONCEPT AND MAIN APPLICATIONS HR3200C series models have been developed as successor models of HR3000C,

More information

FE 35, 40, 55, EC Every time you open the housing, clean the motor with a soft brush.

FE 35, 40, 55, EC Every time you open the housing, clean the motor with a soft brush. FE 35, 40, 55, EC 70 1 Service Manual FE 35, FE 40, FE 55 Electric Trimmers, EC 70 Electric Edger As the design concept of the FE 35 and FE 40 trimmers is almost identical, the descriptions and servicing

More information

Repair Manual 11/99 PS-34. Page 1

Repair Manual 11/99 PS-34. Page 1 Repair Manual /99 PS-4 Page Table of contents Index Technical Data page Special tools 4 Repair instructions, general 0 Chain brake 6 0 Centrifugal clutch 8 0 Oil pump 9-04 Ignition system - 0 Starting

More information

Repair instruction for HYDRAULIC DRIVE UNITS HA1ES / HA \r04eng 0697

Repair instruction for HYDRAULIC DRIVE UNITS HA1ES / HA \r04eng 0697 Repair instruction for HYDRAULIC DRIVE UNITS HA1ES / HA2 Contents list page Safety rules General instructions 1 Operating faults and how to clear them 2 Replacement parts lists 31070 HA1ES 4 31375 HA2

More information

Transmission Overhaul Procedures-Bench Service

Transmission Overhaul Procedures-Bench Service How to Assemble the Lower Reverse Idler Gear Assembly Special Instructions In 1996 Eaton changed the reverse idler system design. In the nut design, the reverse idler bearing was lubricated through a hole

More information

MAINTENANCE PROCEDURE FOR MK21

MAINTENANCE PROCEDURE FOR MK21 MAINTENANCE PROCEDURE FOR MK21-1 - MAINTENANCE PROCEDURE FOR MK 21 1 ST STAGE WARNING: this maintenance procedure is only for appointed Scubapro technicians that followed a complete course on equipment

More information

SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 1" D-HANDLE ROTARY HAMMER SERIAL NUMBER G43A See page 6.

SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 1 D-HANDLE ROTARY HAMMER SERIAL NUMBER G43A See page 6. 00 0 CATALOG NO. EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). = Component of the 14-4-525 522-21 Maintenance Service Kit SEE PAGE TWO FOR THE PROCEDURE ON CHECKING

More information

Pull out clutch E snap ring and withdraw complete clutch pack of clutch E. 6 HP 26 ZF Getriebe GmbH Saarbrücken CD

Pull out clutch E snap ring and withdraw complete clutch pack of clutch E. 6 HP 26 ZF Getriebe GmbH Saarbrücken CD Press down cup spring in the mandrel press with assembly bracket 5x46 002 566 and remove snap ring with suitable pliers. Take out planet carrier and cup spring. Take the O-ring seal off the planet carrier.

More information

Page 1 of 15 Transmission, Model S5-42 ZF Model S5-42 ZF Disassembly NOTE: For 4x4 and F-Super Duty vehicles, skip to Step 5. 1. Attach the transmission to the Bench Mounted Holding Fixture T57L-500-B

More information

Maintenance Information

Maintenance Information 16572679 Edition 2 May 2014 Air Drill QP Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these potentially

More information

VC-NR-100 SERIES STAINLESS STEEL, VERTICAL CANISTER PNEUMATIC ACTUATOR & SSBT SERIES CONTROL TOPS

VC-NR-100 SERIES STAINLESS STEEL, VERTICAL CANISTER PNEUMATIC ACTUATOR & SSBT SERIES CONTROL TOPS VC-NR-100 SERIES STAINLESS STEEL, VERTICAL CANISTER PNEUMATIC ACTUATOR & SSBT SERIES CONTROL TOPS BRADFORD VC-NR-100 SERIES ACTUATOR & CONTROL TOP FEATURES SPECIFICATIONS & DIMENSIONS FEATURES Excellent

More information

13. CRANKCASE/CRANKSHAFT/BALANCER/PISTON/CYLINDER

13. CRANKCASE/CRANKSHAFT/BALANCER/PISTON/CYLINDER 13. CRANKCASE/CRANKSHAFT/BALANCER/PISTON/CYLINDER COMPONENT LOCATION 13-2 SERVICE INFORMATION 13-3 TROUBLESHOOTING 13-4 CRANKCASE SEPARATION 13-5 CRANKSHAFT 13-7 MAIN JOURNAL BEARING 13-9 CRANKPIN BEARING

More information

SPECIAL TOOLS. Core Drilling Machines SERVICE MANUAL. Page 1

SPECIAL TOOLS. Core Drilling Machines SERVICE MANUAL. Page 1 SPECIAL TOOLS Core Drilling Machines Page 1 SERVICE MANUAL Service Manual Necessary Tools for machine assembly BEAST by BBTEC Core Drilling Machines 1 Soft Hammer (preferred plastic head) Art. 6.512.096

More information

Steering Column. Disassembly. 1. Remove instrument panel cover and reinforcement from vehicle as described in this section.

Steering Column. Disassembly. 1. Remove instrument panel cover and reinforcement from vehicle as described in this section. Page 1 of 14 Section 11-04A: Steering Column, Ranger 1997 Aerostar/Ranger Workshop Manual DISASSEMBLY AND ASSEMBLY Procedure revision date: 05/17/2000 Steering Column Disassembly 1. Remove instrument panel

More information

Maintenance Information

Maintenance Information 16575243 Edition 2 October 2013 Air Screwdrivers 1R Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these

More information

MODEL D 10YB POWER TOOLS TECHNICAL DATA AND SERVICE MANUAL ANGLE DRILL D 10YB SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT

MODEL D 10YB POWER TOOLS TECHNICAL DATA AND SERVICE MANUAL ANGLE DRILL D 10YB SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT MODEL D 10YB POWER TOOLS D ANGLE DRILL D 10YB TECHNICAL DATA AND SERVICE MANUAL LIST No. 0193 Jun. 2000 SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT Notice for use Specifications and

More information

GM 3000 AIRLESS PAINT SPRAYERS Drive Housing Replacement Kit Pinion Housing Replacement Kit

GM 3000 AIRLESS PAINT SPRAYERS Drive Housing Replacement Kit Pinion Housing Replacement Kit INSTRUCTIONS 08660 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Rev. B GM 000 AIRLESS PAINT SPRAYERS Drive Housing Replacement Kit 869 Pinion Housing

More information

MODEL HM A01

MODEL HM A01 BREAKER HAMMER MODEL HM800 06-03 5 4 3 2 0 9 8 7 6 5 4 3 2 6 7 8 36 35 32 3 30 9 20 25 26 24 23 22 2 29 28 27 57 56 55 54 53 52 5 50 49 48 47 46 45 44 43 42 39 4 40 4 38 37 34 33 2 3 A0 23 2 Model HM800

More information

57-1. Front door. Tools. Special tools and equipment. T Socket 3320/2 Bit insert for Socket T Assembly tool

57-1. Front door. Tools. Special tools and equipment. T Socket 3320/2 Bit insert for Socket T Assembly tool 57-1 Front door Tools Special tools and equipment T 10011 Socket 3320/2 Bit insert for 3320 3410 Socket T 10034 Assembly tool 57-2 Front door, assembly overview Note: The instrument panel must be removed

More information

Maintenance Information

Maintenance Information 45530136 Edition 1 July 2008 Electric Screwdrivers EL 24V DC Series Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing maintenance on this tool.

More information

TECHNICAL INFORMATION

TECHNICAL INFORMATION TECHNICAL INFORMATION PRODUCT P 1/ 11 Model No. Description TM3010C Multi tool L CONCEPT AND MAIN APPLICATIONS Model TM3010C has been developed based on model TM3000C and equipped with the tool-less accessory

More information

1990 SUSPENSION Front ES250, LS400

1990 SUSPENSION Front ES250, LS400 SUSPENSION - FRONT Article Text 1990 Lexus LS 400 For Lextreme Copyright 1998 Mitchell Repair Information Company, LLC Thursday, January 29, 2004 04:56PM ARTICLE BEGINNING 1990 SUSPENSION Front ES250,

More information

CARTER DOWNDRAFT CARBURETOR Terraplane All Models. Technical Information

CARTER DOWNDRAFT CARBURETOR Terraplane All Models. Technical Information CARTER DOWNDRAFT CARBURETOR 1934 Terraplane All Models Technical Information . Carter W-1 Downdraft Carburetors 1934 Terraplane Challenger, Model KS NOTE: Terraplane Models. Carburetor fitted with Anti-

More information

Installation Instructions

Installation Instructions Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to

More information

MANUAL TRANSAXLE Return to Main Table of Contents

MANUAL TRANSAXLE Return to Main Table of Contents MANUAL TRANSAXLE Return to Main Table of Contents GENERAL... 2 MANUAL TRANSAXLE CONTROL... 12 SHIFT LEVER ASSEMBLY... 14 MANUAL TRANSAXLE... 15 MANUAL TRANSAXLE ASSEMBLY... 17 FIFTH SPEED SYNCHRONIZER

More information

CARBURETION. Tank Mount, Horizontal Crankshaft. Vacu-Jet - All

CARBURETION. Tank Mount, Horizontal Crankshaft. Vacu-Jet - All Page 1 of 1 Vacu-Jet - All Carburetor Adjustment Initial 1. Turn adjustment needle clockwise until it makes light contact with the seat. Do not force. 2. The initial setting of adjustment needle is made

More information

./#0#. 1"&." 1994 ELECTRICAL Suzuki of America Corp. - Starters. Swift

./#0#. 1&. 1994 ELECTRICAL Suzuki of America Corp. - Starters. Swift !"" #$%!& '()!)((*(+,*)- 1994 ELECTRICAL Suzuki of America Corp. - Starters Swift Two types of starter motors are used, conventional and reduction gear. Both types of starters consist of yoke assembly,

More information

Engine, disassembling and

Engine, disassembling and Page 1 of 38 13-1 Engine, disassembling and assembling Lock carrier, moving into service position Special tools and equipment 3369 support tool 1 - Bolts 2 - Bolts 3 - Bolts 4 - Bolts 5 - Bore 45 Nm (33

More information

TECHNICAL INFORMATION

TECHNICAL INFORMATION TECHNICAL INFORMATION Model No. Description SP6000 Plunge Cut Circular Saw 165mm (6-1/2") CONCEPT AND MAIN APPLICATIONS Model SP6000 is the first Makita plunge cut saw. Features great conveniences such

More information

2001 Dodge RAM 3500 PICKUP

2001 Dodge RAM 3500 PICKUP 1 of 76 9/14/2012 7:02 PM 2001 Dodge RAM 3500 PICKUP Submodel: Engine Type: L6 Liters: 5.9 Fuel Delivery: FI Fuel: DIESEL Subarticles MANUAL- NV3500 - DISASSEMBLY MANUAL- NV3500 - DISASSEMBLY MANUAL -

More information

Maintenance Instructions. World Leader in Modular Torque Limiters. JSE AEA Extruder Clutch

Maintenance Instructions. World Leader in Modular Torque Limiters. JSE AEA Extruder Clutch World Leader in Modular Torque Limiters PROTECTING EQUIPMENT& MACHINERYYEARSInstallation and Maintenance Instructions JSE.5-0234AEA Extruder Clutch 1304 Twin Oaks Street Wichita Falls, Texas 76302 (940)

More information

3.2 DRIVE TORQUE HUB. Roll, Leak and Brake Testing SECTION 3 - CHASSIS & TURNTABLE. 3-2 JLG Lift

3.2 DRIVE TORQUE HUB. Roll, Leak and Brake Testing SECTION 3 - CHASSIS & TURNTABLE. 3-2 JLG Lift 3.2 DRIVE TORQUE HUB Roll, Leak and Brake Testing 10 LUG PATTERN Torque-Hub units should always be roll and leak tested before disassembly and after assembly to make sure that the unit's gears, bearings

More information

TCI Trans-Scat

TCI Trans-Scat Page 1 of 5 Return to Instruction Sheet index TCI 400000 Trans-Scat Turbo Hydramatic 400-1965-Up This kit will allow you to re-program your transmission valve body. This kit will give you firm positive

More information

REPAIR MANUAL. Version 02/11/01 CD ZF GETRIEBE GMBH SAARBRÜCKEN

REPAIR MANUAL. Version 02/11/01 CD ZF GETRIEBE GMBH SAARBRÜCKEN REPAIR MANUAL 6 HP-26 Version CD ZF GETRIEBE GMBH SAARBRÜCKEN subject to alterations Copyright 2002 all rights reserved and published by ZF Getriebe GmbH, Saarbrücken, Department MKTD No part of this manual

More information

STARTER - HITACHI Isuzu Trooper II DESCRIPTION TESTING STARTER PERFORMANCE TESTS Starters HITACHI. Isuzu

STARTER - HITACHI Isuzu Trooper II DESCRIPTION TESTING STARTER PERFORMANCE TESTS Starters HITACHI. Isuzu STARTER - HITACHI 1986 Trooper II 1984 Starters HITACHI DESCRIPTION Starter is a conventional 12-volt, 4-pole brush-type motor, with direct or reduction gear drive. The starter-mounted solenoid shifts

More information

Repair Manual. General Pump is a member of the Interpump Group. Ref Rev.A 09-13

Repair Manual. General Pump is a member of the Interpump Group. Ref Rev.A 09-13 Repair Manual General Pump is a member of the Interpump Group 8 INDEX 1. INTRODUCTION..................................................Page 3 2. REPAIR GUIDELINES..............................................Page

More information

The steering column is of a modular construction and features easy to service electrical switches.

The steering column is of a modular construction and features easy to service electrical switches. file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a01.htm~gen~ref.htm Page 1 of 3 Section 11-04A: Steering Column, Ranger DESCRIPTION AND OPERATION 1997 Ranger Workshop Manual Steering Column NOTE:

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS --1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767-- 2505 Lowering Spindle Assembly Installation Instructions ½ TON SILVERADO

More information

4357 / 4860 MX Multi Adjuster

4357 / 4860 MX Multi Adjuster 12_234 Frontfork 4357 / 4860 MX Multi Adjuster Introduction 2 Exploded view 3 Disassembly forkleg 4 Disassembly screw-cap 15 Assembling screw-cap 17 Disassembly cartridge 18 Disassembly compression holder

More information

CHAPTER 22 STARTER Models J05C-TD, J08C-TP and TR

CHAPTER 22 STARTER Models J05C-TD, J08C-TP and TR 1 INDEX STARTER 22-1 22-114E-03 CHAPTER 22 STARTER TROUBLESHOOTING...22-2 STARTER...22-4 22 22-2 STARTER 1 page 1 TROUBLESHOOTING Symptom Possible cause Remedy Engine does not crank, or cranks slowly Key

More information

DM-TRSL (English) Dealer's Manual. ROAD MTB Trekking. City Touring/ Comfort Bike. Shifting lever DEORE XT SL-T8000 DEORE SL-T6000

DM-TRSL (English) Dealer's Manual. ROAD MTB Trekking. City Touring/ Comfort Bike. Shifting lever DEORE XT SL-T8000 DEORE SL-T6000 (English) DM-TRSL001-01 Dealer's Manual ROAD MTB Trekking City Touring/ Comfort Bike URBAN SPORT E-BIKE Shifting lever DEORE XT SL-T8000 DEORE SL-T6000 CONTENTS IMPORTANT NOTICE... 3 TO ENSURE SAFETY...

More information

2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES

2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES 2002-04 DRIVE AXLES Axle Shafts - Front - Ram Pickup 1500 4WD DESCRIPTION Vehicles equipped with 4WD and C205F front axle assembly use equal length axle shaft system to deliver power from front differential

More information

Steering Cylinders. Remove Steering Cylinders. Disassembly and Assembly 920 & 930 WHEEL LOADER VEHICLE SYSTEMS

Steering Cylinders. Remove Steering Cylinders. Disassembly and Assembly 920 & 930 WHEEL LOADER VEHICLE SYSTEMS Disassembly and Assembly 920 & 930 WHEEL LOADER VEHICLE SYSTEMS Steering Cylinders Remove Steering Cylinders 1. Turn the machine all of the way to the left to remove the right steering cylinder. Turn the

More information

CorkSport ort Mazda 3 Adjustable Shifter Mazdaspeed 3, Mazda 3 6-speed and Mazda3 SkyActiv 6-speed

CorkSport ort Mazda 3 Adjustable Shifter Mazdaspeed 3, Mazda 3 6-speed and Mazda3 SkyActiv 6-speed Part # Axl-6-963 CorkSport ort Mazda 3 Adjustable Shifter 2010-2013 Mazdaspeed 3, 2010-2013 Mazda 3 6-speed and 2012-2013 Mazda3 SkyActiv 6-speed Pre-Installation Notes: The CorkSport Adjustable Short

More information

Workshop manual 5018 PDS Product Exploded View Disassembly & Assembling. Shock absorber 5018 PDS OEM Shock absorber 5018 PDS /2002

Workshop manual 5018 PDS Product Exploded View Disassembly & Assembling. Shock absorber 5018 PDS OEM Shock absorber 5018 PDS /2002 Shock absorber 5018 PDS OEM 2000 Introduction 2 Exploded view 3 Disassembly shock absorber 4 Disassembly piston-rod 11 Disassembly adaptor DU-bush 15 Assembling adaptor DU-bush 17 Assembling piston-rod

More information

Installation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog#

Installation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog# Installation Instructions COMPETITION/PLUS SHIFTER 2015-2017 Ford Mustang MT82 6-Speed Manual Transmission Catalog# 3916037 Rev. 00 WORK SAFELY! For maximum safety, perform this installation on a clean,

More information

Servicing front brakes

Servicing front brakes 46-1 Servicing front brakes C54 brake caliper, servicing Special tools and workshop equipment required VAG 1331 Torque wrench (or equivalent) VAG 1410 Torque wrench (or equivalent) VAG 1869/2 Brake pedal

More information

Removing and installing trim panel

Removing and installing trim panel Removing and installing trim panel vw-wi://rl/a.en-gb.a03.5106.29.wi::31914802.xml?xsl=3 1. oldal, összesen: 1 oldal Removing and installing trim panel Removing Carefully prise out trim panel -1- in direction

More information

TECHNICAL INFORMATION Model No. Description

TECHNICAL INFORMATION Model No. Description TECHNICAL INFORMATION Model No. Description 4114, 4114S Angle Cutter 355mm (14") PRODUCT P 1 / 6 CONCEPT AND MAIN APPLICATIONS Model 4114S is the 355mm (14") version of the current 4112S 305mm (12") Angle

More information

1984 Dodge W250 PICKUP

1984 Dodge W250 PICKUP 1984 Dodge W250 PICKUP Submodel: Engine Type: V8 Liters: 5.2 Fuel Delivery: CARB Fuel: GAS Dana 44 MODELS THROUGH 1984 2. Raise and safely support the vehicle, then remove the wheel hub and bearings as

More information

J2 Remove sound insulation/knee guard 1 and side panel 2 on center console

J2 Remove sound insulation/knee guard 1 and side panel 2 on center console J1 Preparations Drive car forward on a level surface so that wheels are straight. Disconnect battery negative lead. Turn ignition key to position 1 so that steering lock is off. J2 Remove sound insulation/knee

More information

2008 Toyota RAV ELECTRICAL Charging (2AZ-FE) - RAV4

2008 Toyota RAV ELECTRICAL Charging (2AZ-FE) - RAV4 2008 ELECTRICAL Charging (2AZ-FE) - RAV4 CHARGING SYSTEM PRECAUTION 1. Check that the battery cables are connected to the correct terminals. 2. Disconnect the battery cables if a quick charge is given

More information

M-7210-Z3 Focus Short-Throw Shifter (fits 2000-April 2002) INSTALLATION INSTRUCTIONS

M-7210-Z3 Focus Short-Throw Shifter (fits 2000-April 2002) INSTALLATION INSTRUCTIONS Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE

More information

SECTION SAFETY AFTERMARKET PRODUCT GUIDE SAFETY

SECTION SAFETY AFTERMARKET PRODUCT GUIDE SAFETY AFTERMARKET PRODUCT GUIDE 1 2 WARNING! Be certain to disengage PTO shaft and to turn off the tractor before making any operational maintenance inspections or repairs. Keep clear of the machine until all

More information

Shock absorber for Automotive TTX36 P/ IL. Workshop Manual

Shock absorber for Automotive TTX36 P/ IL. Workshop Manual TTX6P TTX6IL Shock absorber for Automotive TTX6 P/ IL Workshop Manual Safety precautions General Warnings Note! The shock absorber/front fork/steering damper is an important part of the vehicle and will

More information

Installation Manual TWM Performance Short Shifter Subaru Forester up to 2005

Installation Manual TWM Performance Short Shifter Subaru Forester up to 2005 - 1 - Installation Manual TWM Performance Short Shifter Subaru Forester up to 2005 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift

More information

LJ20 Distributor - Disassembly Inspection Repair

LJ20 Distributor - Disassembly Inspection Repair LJ20 Distributor - Disassembly Inspection Repair Old Codger New To Old Suzuki Jeeps The odometer on this 1972 LJ20 indicated the distributor had less than 10,000 miles of wear but during that time it had

More information

NOTE: Visit our website at for video repair procedures, under the Tools section.

NOTE: Visit our website at   for video repair procedures, under the Tools section. Repair Instructions Hypro Repair Tools: Tool Box No. 3010-0168 1/4" Allen Wrench No. 3020-0008 Support Bars (2) No. 3010-0064 Port Brush No. 3010-0066 1/16" Allen Wrench No. 3020-0009 Brush Holder No.

More information

Dismantling and assembling automatic transmission (A5S560Z) (transmission removed)

Dismantling and assembling automatic transmission (A5S560Z) (transmission removed) 24 00 585 Dismantling and assembling automatic transmission (A5S560Z) (transmission removed) Secure transmission to assembly frame with special tool 24 0 180. Drain off transmission oil. Screw special

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CENTER BEARING SUPPORT ASSEMBLY Removal 1. With transmission in neutral and parking brake off, raise vehicle. Scribe alignment marks on all flange/yokes and slip joints to be disassembled

More information

2004 Lexus LS430. Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS

2004 Lexus LS430. Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS 2004 Lexus LS430 Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS OVERHAUL If the airbag connector is disconnected with the ignition switch in the ON position, DTCs will be recorded. When

More information

TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase.

TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase. TRANSMISSION 6.7 GENERAL See Figure 6-45. The transmission is a five-speed constantmesh type housed in an extension of the crankcase. Mainshaft Neutral Mainshaft st Gear b06x6x Countershaft 4 Out 5 Countershaft

More information

DRIVE SHAFT LOCATION INDEX

DRIVE SHAFT LOCATION INDEX DRIVE SHAFT LOCATION INDEX 2005 DRIVELINE/AXLE Drive Shaft - MX-5 Miata Fig. 1: Identifying Drive Shaft Location DRIVE SHAFT PRE-INSPECTION 1. Inspect the dust boot on the drive shaft for cracks, damage,

More information

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388).

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388). TX420 & 425 240000299 & lower 4. Remove the LH side panel (Fig. 0388). Hydraulic Tandem Pump Removal Note: Cleanliness is a key factor in a successful repair of any hydraulic system. Thoroughly clean all

More information

Performance Brake Caliper Guide Bushing Set Installation Guide

Performance Brake Caliper Guide Bushing Set Installation Guide Performance Brake Caliper Guide Bushing Set Installation Guide Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those

More information

TABLE OF CONTENTS. Cordless Impact Driver. Model No. EY7542. Europe Oceania

TABLE OF CONTENTS. Cordless Impact Driver. Model No. EY7542. Europe Oceania Order Number PTD0707X38CE Cordless Impact Driver Model No. EY7542 Europe Oceania TABLE OF CONTENTS PAGE 1 Warning-------------------------------------------------------------- 2 2 Specifications -----------------------------------------------------

More information

SCION tc STRUT TIE BAR Preparation

SCION tc STRUT TIE BAR Preparation SCION tc 2005 - STRUT TIE BAR Preparation Part Number: 00016-80440 Code: YY1 Kit Contents 1 1 DS Mount Plate 2 1 PS Mount Plate 3 1 Cross Bar 4 1 Hardware Bag Hardware Bag Contents 1 4 8mm Screws 2 4 8mm

More information

PAH, PAHT, PAHT G pumps PAH , PAHT and PAHT G Disassembling and assembling

PAH, PAHT, PAHT G pumps PAH , PAHT and PAHT G Disassembling and assembling Servie guide PAH, PAHT, PAHT G pumps PAH 10-12.5, PAHT 10-12.5 and PAHT G 10-12.5 Disassembling and assembling hpp.danfoss.com Table of Contents 1. Disassembling the pump...3 2. Inspection...7 2.1. Port

More information

MAINTENANCE MANUAL DP-265

MAINTENANCE MANUAL DP-265 MAINTENANCE MANUAL DP-265 Drive Gears Sisu Axles, Inc. Autotehtaantie 1 P.O. Box 189 FIN-13101 Hämeenlinna Finland Phone int + 358 204 55 2999 Fax int + 358 204 55 2900 DP265DG.PDF (2/2003) k Table of

More information

Drive Shaft, Disassemble and Reassemble

Drive Shaft, Disassemble and Reassemble Page 1 of 9 Drive Shaft, Disassemble and Reassemble 1. Illustration of drive shaft 1. Drive shaft 2. Needle roller bearing 3. 5th gear (driving) 4. Radial needle roller bearing 5. 3rd gear (driving) 6.

More information

TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase.

TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase. TRANSMISSION 6.7 GENERAL See Figure 6-46. The transmission is a five-speed constantmesh type housed in an extension of the crankcase. b06x6x Neutral st Gear Mainshaft Mainshaft 4 5 4 5 Countershaft Out

More information

ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type)

ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type) ENGINE MECHANICAL - Engine Tune-Up EM-17 ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT (See steps 1 and 2 on page CO-4) INSPECTION OF ENGINE OIL (See steps 1 and 2 on page LU-5) INSPECTION OF BATTERY (See

More information

I. TWO-STROKE MECHANICAL EN- GINE PARTS

I. TWO-STROKE MECHANICAL EN- GINE PARTS I. TWO-STROKE MECHANICAL EN- GINE PARTS 1. UNIBLOCK ENGINES (AV520-600-750-125) a) INTRODUCTION Fig. 1 shows the short block. Fig. 2 shows an exploded view of the engine. As may be seen the momoblock is

More information

Front seats. j a t CAUTION! Before beginning repairs on the electrical system: Obtain the anti-theft radio security code. Switch the ignition off.

Front seats. j a t CAUTION! Before beginning repairs on the electrical system: Obtain the anti-theft radio security code. Switch the ignition off. j a t Front seats 72-1 CAUTION! Before beginning repairs on the electrical system: Obtain the anti-theft radio security code. Switch the ignition off. Search Advanced Search Disconnect the battery Ground

More information

INSTALLATION GUIDE. KTM 125, 144, Stroke KTM 250, Stroke KTM 250 SXF, XC, XC-W KTM 450, 505 SXF Manual Revision:

INSTALLATION GUIDE. KTM 125, 144, Stroke KTM 250, Stroke KTM 250 SXF, XC, XC-W KTM 450, 505 SXF Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE KTM 125, 144, 200 2-Stroke KTM 250, 300 2-Stroke KTM 250 SXF, XC, XC-W KTM 450, 505 SXF 191-836 Manual Revision: 050307 2002 Rekluse Motor

More information

PR 3. PROPELLER SHAFT FRONT PROPELLER SHAFT ASSEMBLY (for 4WD) DISASSEMBLY

PR 3. PROPELLER SHAFT FRONT PROPELLER SHAFT ASSEMBLY (for 4WD) DISASSEMBLY OPELLER SHAFT FRONT OPELLER SHAFT ASSEMBLY (for 4WD) 3 C029928 DISASSEMBLY 1. INSPECT FRONT OPELLER SHAFT ASSEMBLY (a) Check that the propeller shaft is not damaged or deformed. If necessary, replace the

More information

1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza

1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza 1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza ARTICLE BEGINNING 1995-98 ENGINES Subaru - 1.8L & 2.2L 4-Cylinder 1995-97: Impreza (1.8L) 1995-98: Impreza (2.2L), Legacy (2.2L) * PLEASE READ THIS FIRST

More information