DutyMax Hydraulic Sprayers

Size: px
Start display at page:

Download "DutyMax Hydraulic Sprayers"

Transcription

1 Repair DutyMax Hydraulic Sprayers 3A2247A EN - For professional use only - - Not approved for use in European explosive atmosphere locations - Models: 24M054 (EH200DI), 24M055 (GH200DI), 24M056 (EH300DI), 24M057 (GH300DI) 3300 psi (22.8 MPa, 228 bar) Maximum Working Pressure Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. See page 3 for model information. 3A A Blue Texture Gun Inline Texture Gun ti18188a

2 Table of Contents Models General Repair Information Pressure Relief Procedure Maintenance Troubleshooting Hydraulic Pump Removal Installation Fan Belt Removal Installation Electric Motor Starter Removal Installation Electric Motor Removal Installation Hydraulic Motor Rebuild Removal Installation Hydraulic Motor Hydraulic Oil/Filter Change Removal Installation Displacement Pump Removal Installation Check Valve Repair Removal Installation Wiring Diagram Notes Technical Data Graco Standard Warranty A2247A

3 Models Models GH200DI GH300DI EH200DI 240 VAC 50 Hz 1 Phase EH300DI CSA 400VAC 50 Hz 3 Phase BLUE GUN 1/4 in. x 3 ft WHIP 3/8 in. x 50 ft HOSE INLINE GUN 3/8 in. x 12 in. WHIP 1/2 in. x 50 ft HOSE 24M054 24M055 24M056 24M057 Electric Motor Kit Options Kit Number Sprayer Model Description 24M666 EH200DI Gas Conversion Kit 24M667 EH300DI Gas Conversion Kit 24M668 GH200DI Electric Conversion Kit 24M669 GH300DI Electric Conversion Kit 3A2247A 3

4 Models Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable. DANGER HIGH VOLTAGE ELECTRIC SHOCK HAZARD This equipment uses high voltage power. Improper contact with high voltage equipment will cause death or serious injury. Turn off and disconnect power cord before servicing equipment. This equipment must be grounded. Connect only to grounded power source. Use only 3-wire extension cords for 240V and single phase models. Use only 5-wire extension cords for 400 AC and three phase models. Ensure ground prongs are intact on power and extension cords. Do not expose to rain. Store indoors. All electrical wiring must be done by a qualified electrician and comply with all local codes and regulations. 4 3A2247A

5 Models WARNING FIRE AND EXPLOSION HAZARD Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion: Use equipment only in well ventilated area. Do not fill fuel tank while engine is running or hot; shut off engine and let it cool. Fuel is flammable and can ignite or explode if spilled on hot surface. Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static arc). Keep work area free of debris, including solvent, rags and gasoline. Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes are present. Ground all equipment in the work area. See Grounding instructions. Use only grounded hoses. Hold gun firmly to side of grounded pail when triggering into pail. Do not use pail liners unless they are antistatic or conductive. Stop operation immediately if static sparking occurs or you feel a shock. Do not use equipment until you identify and correct the problem. Keep a working fire extinguisher in the work area. SKIN INJECTION HAZARD High-pressure spray is able to inject toxins into the body and cause serious bodily injury. In the event that injection occurs, get immediate surgical treatment. Do not aim the gun at, or spray any person or animal. Keep hands and other body parts away from the discharge. For example, do not try to stop leaks with any part of the body. Always use the nozzle tip guard. Do not spray without nozzle tip guard in place. Use Graco nozzle tips. Use caution when cleaning and changing nozzle tips. In the case where the nozzle tip clogs while spraying, follow the Pressure Relief Procedure for turning off the unit and relieving the pressure before removing the nozzle tip to clean. Do not leave the unit energized or under pressure while unattended. When the unit is not in use, turn off the unit and follow the Pressure Relief Procedure for turning off the unit. Check hoses and parts for signs of damage. Replace any damaged hoses or parts. This system is capable of producing 3300 psi. Use Graco replacement parts or accessories that are rated a minimum of 3300 psi. Always engage the trigger lock when not spraying. Verify the trigger lock is functioning properly. Verify that all connections are secure before operating the unit. Know how to stop the unit and bleed pressure quickly. Be thoroughly familiar with the controls. PRESSURIZED EQUIPMENT HAZARD Fluid from the equipment, leaks, or ruptured components can splash in the eyes or on skin and cause serious injury. Follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing equipment. Tighten all fluid connections before operating the equipment. Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. 3A2247A 5

6 Models WARNING MOVING PARTS HAZARD Moving parts can pinch, cut or amputate fingers and other body parts. Keep clear of moving parts. Do not operate equipment with protective guards or covers removed. Pressurized equipment can start without warning. Before checking, moving, or servicing equipment, follow the Pressure Relief Procedure and disconnect all power sources. EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury. Do not operate the unit when fatigued or under the influence of drugs or alcohol. Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals. Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer s warnings. For complete information about your material, request MSDS from distributor or retailer. Do not leave the work area while equipment is energized or under pressure. Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use. Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer s replacement parts only. Do not alter or modify equipment. Alterations or modifications may void agency approvals and create safety hazards. Make sure all equipment is rated and approved for the environment in which you are using it. Use equipment only for its intended purpose. Call your distributor for information. Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not kink or over bend hoses or use hoses to pull equipment. Keep children and animals away from work area. Comply with all applicable safety regulations. PRESSURIZED ALUMINUM PARTS HAZARD Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical reaction and equipment rupture. Failure to follow this warning can result in death, serious injury, or property damage. Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents. Many other fluids may contain chemicals that can react with aluminum. Contact your material supplier for compatibility. SUCTION HAZARD Powerful suction could cause serious injury. Never place hands near the pump fluid inlet when pump is operating or pressurized. CARBON MONOXIDE HAZARD Exhaust contains poisonous carbon monoxide, which is colorless and odorless. Breathing carbon monoxide can cause death. Do not operate in an enclosed area. 6 3A2247A

7 Models WARNING TOXIC FLUID OR FUMES HAZARD Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed. Read MSDSs to know the specific hazards of the fluids you are using. Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines. BURN HAZARD Equipment surfaces and fluid that s heated can become very hot during operation. To avoid severe burns: Do not touch hot fluid or equipment. PERSONAL PROTECTIVE EQUIPMENT Wear appropriate protective equipment when in the work area to help prevent serious injury, including eye injury, hearing loss, inhalation of toxic fumes, and burns. This protective equipment includes but is not limited to: Protective eyewear, and hearing protection. Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer. 3A2247A 7

8 General Repair Information General Repair Information DANGER DA HIGH VOLTAGE ELECTRIC SHOCK HAZARD This equipment uses high voltage power. Improper contact with high voltage equipment will cause death or serious injury. Turn off and disconnect power cord before servicing equipment. This equipment must be grounded. Connect only to grounded power source. Use only 3-wire extension cords for 240V and single phase models. Use only 5-wire extension cords for 400 AC and three phase models. Ensure ground prongs are intact on power and extension cords. Do not expose to rain. Store indoors. All electrical wiring must be done by a qualified electrician and comply with all local codes and regulations. Grounding Ground sprayer with grounding clamp to earth ground for safe sprayer operation. SAE O-Ring Installation 1. Unscrew lock nut to touch fitting. A 2. Lubricate o-ring (A) ti5414a 3. Screw in fitting hand tight. To reduce risk of serious injury, do not touch moving parts with fingers or tools while testing repair. Shut off sprayer when repairing. Install all covers, gaskets, screws and washers before operating sprayer. Keep all screws, nuts, washers, gaskets, and electrical fittings removed during repair procedures. These parts are not normally provided with replacement assemblies. Test repair after problem is corrected. If sprayer does not operate properly, review repair procedure to verify procedure was done correctly. If necessary, see Troubleshooting, page 10, for other possible solutions. Install belt guard before operation of sprayer and replace if damaged. Belt guard reduces risk of pinching and loss of fingers; see preceding warning. Install hydraulic motor shield before operation and replace if damaged. Hydraulic motor shield reduces risk of pinching and loss of fingers; see preceding warning. ti5415a 4. Unscrew fitting until oriented properly. ti5416a 5. Tighten lock nut to indicated torque. (Make sure washer is seated properly without pinching o-ring). ti5417a 8 3A2247A

9 Pressure Relief Procedure Pressure Relief Procedure Follow the Pressure Relief Procedure whenever you see this symbol. 5. Turn prime valve down. This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing the equipment. 1. Set pump valve OFF. ti5266b If after following these steps you suspect the spray tip or hose is still clogged or that pressure has not been fully relieved, very slowly loosen tip guard retaining nut or hose end coupling to relieve pressure gradually. Then loosen completely. Maintenance NOTE: For detailed engine maintenance and specifications, see separate Honda owner s engine manual (supplied). ti9686a 2. Turn gas engine or electric motor OFF. DAILY: Check hydraulic oil level and fill as necessary. DAILY: Check gas engine oil level and fill as necessary. O I Electric Models Single Phase 3. Unplug power cord. I O Electric Models Three Phase OFF ON Gas Models DAILY: Check hose for wear and damage. DAILY: Check gun safety for proper operation. DAILY: Check pressure drain valve for proper operation. DAILY: Check that displacement pump is tight. DAILY: Check level of Throat Seal Liquid (TSL) in displacement pump packing nut. Fill nut, if necessary. Keep TSL in nut to help prevent fluid buildup on piston rod and premature wear of packings and pump corrosion. WEEKLY/DAILY: Remove any debris or media from hydraulic rod. ti18812a ti7529a 4. Turn pressure to lowest setting. Trigger gun into pail to relieve pressure. AFTER EACH 100 HOURS OF OPERATION: Change engine oil (see Honda engine owner s manual for correct oil viscosity). SEMI-ANNUALLY: Check belt wear, replace if necessary. YEARLY OR 2000 HOURS: Replace belt. Replace hydraulic oil and filter with Graco hydraulic oil (5 gallon/20 liter) or (1 gallon/3.8 liter) and filter SPARK PLUG: Use only BPRGES or W20EPR-U (NIPPONDENSO) plugs. Gap plug to in ( mm). Use spark plug wrench when installing or removing plug. 3A2247A 9

10 Troubleshooting Troubleshooting PROBLEM CAUSE SOLUTION Gas engine pulls hard (won't start) Hydraulic pressure is too high Turn hydraulic pressure knob counter clockwise to lowest setting. Gas engine does not start Switch OFF, low oil, no gasoline Consult engine manual, supplied. Gas engine doesn't work properly Faulty engine Consult engine manual, supplied. Elevation Consult engine manual, supplied. Electric motor does not start or starts slowly Electric motor does not work properly No power Cord not connected to power source Switch OFF Incorrect power source Incorrect amp setting on motor starter (3 phase motor only) Over current switch has tripped Hydraulic pressure is too high Incorrect power source Low voltage to motor 3 phase motors: A phase of three phase power has open circuit Faulty motor Check power source; check circuit breakers and/or fuses. Reset/replace as required. Connect plug to receptacle (grounded with properly sized circuit breaker and/or fuses). 1 phase motors: Turn on/off switch to ON. 3 phase motors: Push ON switch. Have a certified electrician or authorized Graco Repair Center evaluate and repair. See Technical Data, page 30. NOTE: If using the EH300DI (24M056) sprayer, the generator must be sized for 15 kw output minimum. Have a certified electrician or authorized Graco Repair Center evaluate and repair. See Technical Data, page 30. Have a certified electrician or authorized Graco Repair Center evaluate and repair. See Technical Data, page 30. Turn hydraulic pressure knob counter clockwise to lowest setting. Have a certified electrician or authorized Graco Repair Center evaluate and repair. See Technical Data, page 30. Have a certified electrician or authorized Graco Repair Center evaluate and repair. See Technical Data, page 30. Have a certified electrician or authorized Graco Repair Center evaluate and repair. See Technical Data, page 30. Have a certified electrician or authorized Graco Repair Center evaluate and repair. See Technical Data, page A2247A

11 Troubleshooting PROBLEM CAUSE SOLUTION Gas engine / electric motor operates but displacement pump does not operate Displacement pump operates, but output is low on upstroke Displacement pump operates but output is low on downstroke and/or on both strokes Paint leaks and runs over side of wetcup Hydraulic pump valve is OFF Set hydraulic pump valve ON. Pressure setting too low Increase pressure, page Operation manual. Displacement pump outlet filter (if used) Clean the filter. is dirty or clogged Tip or tip filter (if used) is clogged Remove tip and/or filter and clean. Hydraulic fluid too low Shut off sprayer. Add fluid*. Belt is off pulley, worn or broken Replace. See Repair manual. Hydraulic pump worn or damaged Bring sprayer to Graco distributor for repair. Dried paint seized paint pump rod Service pump. See manual Hydraulic motor not shifting Set pump valve OFF. Turn pressure down. Turn engine OFF. Pry rod up or down until hydraulic motor shifts. See Repair manual. For 3 Phase electric motor only: Red phase sequence light is ON, indicating motor rotating in the wrong direction Remove plug from receptacle and rotate plug phase screw. See Operation manual. Piston ball check not seating properly Service piston ball check. See manual Piston packings worn or damaged Replace packings. See manual Piston packings worn or damaged Intake valve ball check not seating properly Displacement pump air leak Tighten packing nut or replace packings. See manual Service intake valve ball check. See manual Loosen wet-cup Tighten wet-cup enough to stop leakage. Throat packings worn or damaged Replace packings. See manual Excessive leakage around hydraulic Piston rod seal worn or damaged Replace these parts. See Repair manual. motor piston rod wiper Fluid delivery is low Pressure setting too low Increase pressure, see Operation manual. Displacement pump outlet filter (if used) Clean filter. is dirty or clogged Hydraulic motor is worn or damaged Bring sprayer to Graco distributor for repair. Large pressure drop in fluid hose Use larger diameter or shorter hose. Sprayer overheats Paint build up on hydraulic components Clean hydraulic components. Oil level is low Fill with oil. See Operation manual. Inlet to hydraulic pump pulley/cooling fan Remove obstructions. is obstructed Inlet to 3 phase electric motor cooling fan Remove obstructions. is obstructed. Spitting from gun Air in fluid pump or hose Check for loose connections on siphon assembly, tighten, then reprime pump. Fluid supply is low or empty Refill supply container. Excessive hydraulic pump noise Low hydraulic fluid level Turn sprayer OFF. Add fluid*. Air in hydraulic lines Bleed lines. See Repair manual. *Check hydraulic fluid level often. Do not allow it to become too low. Use only Graco approved hydraulic fluid. 3A2247A 11

12 Hydraulic Pump Hydraulic Pump Removal 5. Raise electric motor (or gas engine) and remove belt (44). This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing the equipment. Let hydraulic system cool before beginning service. 1. Relieve pressure, page Place drip pan or rags under sprayer to catch hydraulic oil that leaks out during repair. 3. Remove drain plug (202) and oil filter (227) and allow hydraulic oil to drain. ti18350a 6. Remove two set screws (197) and fan pulley (96) ti18351a 7. Remove case drain tube (225) ti18348a Remove screw (172), nut (173) and belt guard (117). 8. Remove elbow (221). ti18352a ti18349a ti18353a 12 3A2247A

13 Hydraulic Pump 9. Remove hose (276) from elbow (226). Remove elbow (226) from hydraulic pump (220). 12. Remove four screws (277) and hydraulic pump (220) from reservoir cover (209) ti18354a Remove hydraulic hose (288) from reservoir cover (209). 209 ti18357a Installation 1. Install hydraulic pump (220) to reservoir cover (209) with four screws (277) (ensure o-rings 210 and 211 are in place); torque in-lb (10-12 N m) Remove eight screws (212) reservoir cover (209) filter assembly (206) and gasket (203) ti18355a 2. Install gasket (203) filter assembly (206) and reservoir cover (209) with eight screws (212). Torque in-lb (12-14 N m). 3. Install hydraulic hose (288) to reservoir cover (209). 4. Install elbow (226) in hydraulic pump (220). Install hose (276) in elbow (226). Torque to 15 ft-lb (20.3 N m). 5. Install elbow (221); torque to 15 ft-lb (20.3 N m). 6. Install case drain tube (225); torque to 15 ft-lb (20.3 N m). 7. Install fan pulley (96) with two set screws (197) Raise electric motor (or gas engine) and install belt (44). 203 ti18356a 9. Install belt guard (117) with screw (172) and nut (173). 10. Install drain plug (202). Install oil filter (227); tighten 3/4 turn after gasket contacts base. Fill hydraulic pump with Graco hydraulic oil, page 6, through elbow (221) port until full. Fill reservoir with remaining hydraulic oil. 11. Start up and allow pump to operate at low pressure for approximately 5 minutes to purge all air. 12. Check oil hydraulic oil and top off, if required. 3A2247A 13

14 Fan Belt Fan Belt Removal This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing the equipment. 1. Perform Pressure Relieve Procedure, page Loosen belt guard knob (55). 3. Rotate belt guard (117) up. 4. Lift electric motor or gas engine up to remove tension on belt (44). 5. Remove belt from pulley (43) and fan pulley (96). Installation 1. Thread belt (44) around drive pulley (43) and fan pulley (96). 2. Let electric motor (119) down to put tension on belt. 3. Rotate belt guard (117) down. 4. Tighten belt guard knob (55) ti18342a Belt Table Unit Part Number Description 24M V-Belt AX42 24M V-Belt AX41 24M V-belt AX48 24M V-Belt Ax A2247A

15 Electric Motor Starter Electric Motor Starter DANGER DA HIGH VOLTAGE ELECTRIC SHOCK HAZARD This equipment uses high voltage power. Improper contact with high voltage equipment will cause death or serious injury. Turn off and disconnect power cord before servicing equipment. This equipment must be grounded. Connect only to grounded power source. Use only 3-wire extension cords for 240V and single phase models. Use only 5-wire extension cords for 400 AC and three phase models. Ensure ground prongs are intact on power and extension cords. Do not expose to rain. Store indoors. All electrical wiring must be done by a qualified electrician and comply with all local codes and regulations. This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing the equipment. Removal 3 Phase, 400 VAC, 50 Hz, Electric Motor Starter ti18617a Relieve pressure, page 9. Unplug power cord. 2. Remove Fan Belt, page Loosen electric motor nut (205). Swing motor retainer bracket (204) out. 200 ti5384a 4. Remove motor assembly from sprayer. ti18749a 3A2247A 15

16 Electric Motor Starter 5. Remove motor junction box cover (J). 6. Tilt motor junction box cover back and disconnect three power leads (brown, black, and grey wires) and the yellow and green ground wire (see Wiring Diagram, page 29). J Installation 3 Phase, 400 VAC, 50 Hz, Electric Motor Starter S ti18700a Remove cable strain relief fitting (S) from motor junction cover and pull motor power leads and motor ground wire from motor junction cover Remove six screws (200) from motor mounting bracket (195). 9. Remove motor starter assembly (198). 190 ti18617a Install motor starter (198) on motor starter bracket (195). 2. Install six screws (200), into motor starter (198). Torque screws to 20 in-lb (2.3 N m). 3. Remove motor junction box cover (J). 4. Remove strain relief fitting (S) from motor junction box cover (J). 5. Slide strain relief fitting (S) over motor cable power leads. 6. Screw strain relief fitting (S) into motor junction box cover (J). J S ti18700a 16 3A2247A

17 Electric Motor Starter 7. Be sure gasket is in position on motor junction box cover. Connect yellow and green ground wire to motor junction box ground connection. Connect power leads as follows: Brown wire to motor terminal U1 Black wire to motor terminal V1 Grey wire to motor terminal W1 See Wiring Diagram, page 29, for connection locations. Torque power leads to 28 in-lb (3.2 N m). Torque ground lead to 28 in-lb (3.2 N m). 8. Install motor junction box cover (J) to motor junction box. Torque junction box cover to 28 in-lb (3.2 N m). NOTICE Make sure wires are completely inside motor junction box and will not be pinched between motor junction box and motor junction box cover. Wires will be damaged and create an electrical hazard if pinched. 10. Swing electric motor retainer bracket (204) in. Tighten electric motor nut (205). ti5387a 11. Install Fan Belt, page Check to make sure fan pulley and motor pulley are in line. Also check to make sure fan pulley shaft and motor pulley shaft are parallel. Adjust as required. 9. Install motor assembly on sprayer. ti18748a 3A2247A 17

18 Electric Motor Electric Motor DANGER HIGH VOLTAGE ELECTRIC SHOCK HAZARD This equipment uses high voltage power. Improper contact with high voltage equipment will cause death or serious injury. Turn off and disconnect power cord before servicing equipment. This equipment must be grounded. Connect only to grounded power source. Use only 3-wire extension cords for 240V and single phase models. Use only 5-wire extension cords for 400 AC and three phase models. Ensure ground prongs are intact on power and extension cords. Do not expose to rain. Store indoors. All electrical wiring must be done by a qualified electrician and comply with all local codes and regulations. DA This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing the equipment. Removal 1 Phase, 240 VAC, 50 Hz Electric Motor ti18343a Relieve pressure, page 9. Unplug power cord. 2. Remove Fan Belt, page Loosen electric motor nut (205). Swing motor retainer bracket (204) out ti5384a 4. Remove motor assembly from sprayer. ti18192a 5. Remove four screws (30), nuts (174), handle (175), bottom isolator plate (190) and motor mounting plate (99) from electric motor. 6. Loosen set screws (133) and remove pulley (43) from electric motor. 18 3A2247A

19 Electric Motor 3 Phase, 400 VAC, 50 Hz, Electric Motor Loosen electric motor nut (205). Swing motor retainer bracket (204) out ti5384a Remove motor assembly from sprayer. 30 ti18617a Relieve pressure, page 9. Unplug power cord. 2. Remove Fan Belt, page Remove motor junction box cover (J). ti18749a 6. Tilt motor junction box cover back and disconnect three power leads (brown, black, and grey wires) and the yellow and green ground wire (see Wiring Diagram, page 29). J S ti18700a 7. Remove cable strain relief fitting (S) from motor junction cover and pull motor power lead (3) and motor ground wire from motor junction cover. 8. Remove four screws (30), nuts (174) and handle (175) from motor mounting bracket (99). 9. Remove four screws (23), nuts (174), and electric motor (119) from motor mounting bracket (99). 10. Loosen set screws (2) and remove pulley (43) from electric motor. 3A2247A 19

20 Electric Motor Installation 3. Install motor assembly on sprayer. 1 Phase, 240 VAC, 50 Hz Electric Motor ti18193a 4. Swing electric motor retainer bracket (204) in. Tighten electric motor nut (205). ti18343a ti5387a 5. Install Fan Belt, page Install pulley (43) and set screws (133). Torque set screws to 60 in-lb (6.8 N m). Make sure pulley is flush with end of electric motor shaft. 2. Install handle (175), bottom isolator plate (190) and rocker plate (99) to electric motor (119) with four screws (30) and nuts (174). Motor should be positioned all the way forward on rocker plate. Torque screws (30) to 225 in-lb (25.4 N m). 6. Check to make sure fan pulley and motor pulley are in line. Also check to make sure fan pulley shaft and motor pulley shaft are parallel. Adjust as required. Motor Pulley (133) (end of motor pulley should be flush with end of motor shaft) Motor Shaft Parallel Fan Pulley Shaft Fan Pulley (43) ti18697a In Line ti18750a 20 3A2247A

21 Electric Motor 3 Phase, 400 VAC, 50 Hz, Electric Motor Slide strain relief fitting (S) over motor cable power leads. 7. Screw strain relief fitting (5) into motor junction box cover (J). J S ti18617a Install pulley (43) and tighten set screws. Torque set screws to 60 in-lb (6.8 N m). Make sure pulley is flush with end of electric motor shaft. 2. Install four screws (23), nuts (174) and electric motor to motor mounting bracket (99). Motor should be centered in motor slots. Torque screws to 225 in-lb (25.4 N m). ti18700a 8. Be sure gasket is in position on motor junction box cover. Connect three power leads and ground. Connect yellow and green ground wire to motor junction box ground connection. Connect power leads as follows: Brown wire to motor terminal U1 Black wire to motor terminal V1 Grey wire to motor terminal W1 See Wiring Diagram, page 29, for connection locations. Torque power leads to 28 in-lb (3.2 N m). Torque ground lead to 28 in-lb (3.2 N m). 9. Install motor junction box cover (J) to motor junction box. Torque junction box cover to 28 in-lb (3.2 N m). NOTICE Make sure wires are completely inside motor junction box and will not be pinched between motor junction box and motor junction box cover. Wires will be damaged and create an electrical hazard if pinched. ti18696a 10. Install motor assembly on sprayer. 3. Install four screws (30), nuts (174) and handle (175) to motor mounting bracket (99). Torque screws to 225 in-lb (25.4 N m). 4. Remove motor junction box cover (J). 5. Remove strain relief fitting (S) from motor junction box cover (J). ti18748a 3A2247A 21

22 Electric Motor 11. Swing electric motor retainer bracket (204) in. Tighten electric motor nut (205). Motor Pulley (133) FLUSH (Motor pulley to end of motor shaft) ti5387a 12. Install Fan Belt, page Check to make sure fan pulley and motor pulley are in line. Also check to make sure fan pulley shaft and motor pulley shaft are parallel. Adjust as required. Parallel Motor Shaft ti18705a Fan Pulley Shaft Fan Pulley (43) In Line 22 3A2247A

23 Hydraulic Motor Rebuild Hydraulic Motor Rebuild Removal Installation This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing the equipment. 1. Perform Pressure Relief Procedure, page Place drip pan or rags under sprayer to catch hydraulic oil that leaks out during repair. 3. Remove Displacement Pump, page Remove hydraulic lines (271, 288) from fittings (226) at top left and right side of hydraulic motor. 5. Loosen jam nut (264). 6. Unscrew and remove hydraulic motor cap (265). 7. Slide piston rod/hydraulic motor cap assembly (A) from hydraulic motor cylinder (263). FLYING PARTS HAZARD Detent spring has high energy potential. If detent spring is released without due care detent spring and balls could fly into the eyes of the disassembler. Wear safety glasses when removing or installing detent spring and balls. Failure to wear safety glasses when removing detent spring could result in eye injury or blindness. 1. Slide piston rod assembly (A) into hydraulic motor cylinder (263). 2. Screw down hydraulic motor cap (268). Unscrew hydraulic motor cap until inlet and outlet align with hydraulic line fittings and test hole in hydraulic motor cap points toward belt guard (117). 3. Torque jam nut (264) against hydraulic motor cap (268) to 150 ft-lb (17 N m). 4. Install hydraulic lines (271, 288) to fittings (226) to top left and right side of hydraulic motor; torque to 40 ft-lb (54.2 N m). 5. Do Displacement Pump, Installation, page Start engine and operate pump for 30 seconds. Turn engine OFF. Check hydraulic oil level and fill with Graco hydraulic oil, page 25. 3A2247A 23

24 Hydraulic Motor Rebuild Hydraulic Motor test hole ti8817a A ti8818a 24 3A2247A

25 Hydraulic Oil/Filter Change Hydraulic Oil/Filter Change Removal This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing the equipment Perform Pressure Relieve Procedure, page Place drip pan or rags under sprayer to catch hydraulic oil that drains out. 3. Remove drain plug (202) page 12. Allow hydraulic oil to drain. 4. Unscrew filter (227) slowly - oil runs into groove and drains out rear. Installation 1. Install drain plug (202) and oil filter (227). Tighten oil filter 3/4 turn after gasket contacts base. ti18348a 2. Fill with five quarts of Graco hydraulic oil (5 gallon/20 liter) or (1 gallon/3.8 liter). 3. Check oil level. 3A2247A 25

26 Displacement Pump Displacement Pump NOTE: It is recommended that the check valve be repaired at the same time as the pump. For check valve repair, see manual 3A2338. Removal 6. Open clamp (247). 247 ti8833b This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing the equipment. 1. Flush pump. 2. Perform Pressure Relief Procedure, page Remove hydraulic motor guard. 7. Slide coupler cover (180) up to fully expose rod couplers (179) Remove rod couplers (179). 179 ti8829b 179 ti18701a 4. Separate drain hose from sprayer. ti8830b 9. Remove pump (111) from sprayer. 111 ti18703a 5. Remove pin. ti8832b 10. Remove paint hose fitting (67) and paint hose (63) from pump fitting. ti8831b NOTE: Support pump with your hand before opening T-handle ti9951b 26 3A2247A

27 Displacement Pump Installation 1. If needed, place pump rod in adjustment casting and pull pump to lengthen rod. 5. Slide coupler cover (180) up to expose pump rod. Install rod couplers (179) over rod ti8834b 2. Install pump (111) in sprayer. ti8956b 6. Slide couple cover (180) down over rod couplers (179). ti8959b Close clamp (247) around pump (111) and push it closed Install hydraulic motor guard. ti8955b ti8958b 4. Install paint hose fitting (190) and paint hose (63) to pump connection. ti18701a 8. Install pin. ti 8954b ti8957b 3A2247A 27

28 Check Valve Repair Check Valve Repair 2. Use 1.5 in. (38 mm) wrench to securely tighten check valve to pump. This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing the equipment. Removal 1. Flush pump. Perform Pressure Relief Procedure, page 9. ti18702a 3. Replace Displacement Pump, page Connect paint hose and hand tighten to 70 in-lb (8 N m). 2. Remove Displacement Pump, page Remove check valve assembly (64) from displacement pump (111). ti18600a 5. Verify latch lock is in locked position. ti18699a Installation 1. Apply pipe sealant to check valve inlet (64f) threads and install o-ring (64a) to housing (64b). ti18698a 6. Attach drain hose to sprayer. 64f 64b 64a ti18598a ti18703a 28 3A2247A

29 Wiring Diagram Wiring Diagram EH300 Models (3 Phase Motor) V2 W1 U2 V1 W2 U1 L3 MOTOR N N 2L3 2T3 2L2 2T2 2L1 2T1 L2 L1 N PLUG GREY BLACK GREEN/YELLOW BROWN MOTOR STARTER GREY BLACK BROWN GREEN/YELLOW BLUE ti18616a 3A2247A 29

30 Technical Data Technical Data EH200DI U.S. Metric Maximum Pressure psi (bar) Hydraulic Reservoir Capacity Gallons (Liters) Motor HP (kw) Voltage, Amperage Frequency Phase 220 VAC, 15.0 A, 50 Hz, 1 Phase 220 VAC, 15.0 A, 50 Hz, 1 Phase Maximum Tip size (paint) Maximum Delivery (paint) gpm (lpm) Fluid Inlet in. [npsm (m)] 1 1 Fluid Outlet in. [npsm (m)] 3/8 3/8 Hose Connection [npt (f)] 3/8 3/8 Cycles per gallon (l) (paint) Dimensions and Weight Length (handle bar retracted) in. (cm) Width in. (cm) Height (handle bar retracted) in. (cm) Weight lb (kg) Sound Levels (Measured at maximum normal load conditions) Engine HP Sound Pressure db(a) Sound Power db(a) Maximum back fuse rating for EH300DI: Fuse type am: 63 A Fuse type gl: 80 A NOTE: Under voltage release coil in motor starter for EH300DI will not energize if voltage is less than 85% of listed voltage in Technical Data table. Under voltage release coil in motor starter for EH300DI will de-energize and sprayer will stop if voltage drops to 85% of rated nominal voltage. Voltage will need to be increased and sprayer will need to be restarted. NOTE: To operate the EH300DI (24M056) sprayer with a generator, the generator must be sized for 15 kw output (minimum). Basic Sprayer Wetted Parts: Zinc and nickel-plated carbon steel, stainless steel, PTFE, acetal, chrome plating, leather, V-Max UHMWPE, aluminum, tungsten carbide, ceramic, nylon 30 3A2247A

31 Technical Data GH200DI U.S. Metric Maximum Pressure psi (bar) Hydraulic Reservoir Capacity Gallons (Liters) Motor HP (kw) Maximum Tip size (paint) Maximum Delivery (paint) gpm (lpm) Fluid Inlet in. [npsm (m)] 1 1 Fluid Outlet in. [npsm (m)] 3/8 3/8 Hose Connection [npt (f)] 3/8 3/8 Cycles per gallon (l) (paint) Dimensions and Weight Length (handle bar retracted) in. (cm) Width in. (cm) Height (handle bar retracted) in. (cm) Weight lb (kg) Sound Levels (Measured at maximum normal load conditions) Engine HP Sound Pressure db(a) Sound Power db(a) Maximum back fuse rating for EH300DI: Fuse type am: 63 A Fuse type gl: 80 A NOTE: Under voltage release coil in motor starter for EH300DI will not energize if voltage is less than 85% of listed voltage in Technical Data table. Under voltage release coil in motor starter for EH300DI will de-energize and sprayer will stop if voltage drops to 85% of rated nominal voltage. Voltage will need to be increased and sprayer will need to be restarted. NOTE: To operate the EH300DI (24M056) sprayer with a generator, the generator must be sized for 15 kw output (minimum). Basic Sprayer Wetted Parts: Zinc and nickel-plated carbon steel, stainless steel, PTFE, acetal, chrome plating, leather, V-Max UHMWPE, aluminum, tungsten carbide, ceramic, nylon 3A2247A 31

32 Technical Data EH300DI U.S. Metric Maximum Pressure psi (bar) Hydraulic Reservoir Capacity Gallons (Liters) Motor HP (kw) Voltage, Amperage Frequency Phase 400 VAC, 11.0 A, 50 Hz, 3 Phase 400 VAC, 11.0 A, 50 Hz, 3 Phase Maximum Tip size (paint) Maximum Delivery (paint) gpm (lpm) Fluid Inlet in. [npsm (m)] 1 1 Fluid Outlet in. [npsm (m)] 1/2 1/2 Hose Connection [npt (f)] 1/2 1/2 Cycles per gallon (l) (paint) Dimensions and Weight Length (handle bar retracted) in. (cm) Width in. (cm) Height (handle bar retracted) in. (cm) Weight lb (kg) Sound Levels (Measured at maximum normal load conditions) Engine HP Sound Pressure db(a) Sound Power db(a) Maximum back fuse rating for EH300DI: Fuse type am: 63 A Fuse type gl: 80 A NOTE: Under voltage release coil in motor starter for EH300DI will not energize if voltage is less than 85% of listed voltage in Technical Data table. Under voltage release coil in motor starter for EH300DI will de-energize and sprayer will stop if voltage drops to 85% of rated nominal voltage. Voltage will need to be increased and sprayer will need to be restarted. NOTE: To operate the EH300DI (24M056) sprayer with a generator, the generator must be sized for 15 kw output (minimum). Basic Sprayer Wetted Parts: Zinc and nickel-plated carbon steel, stainless steel, PTFE, acetal, chrome plating, leather, V-Max UHMWPE, aluminum, tungsten carbide, ceramic, nylon 32 3A2247A

33 Technical Data GH300DI U.S. Metric Maximum Pressure psi (bar) Hydraulic Reservoir Capacity Gallons (Liters) Motor HP (kw) Maximum Tip size (paint) Maximum Delivery (paint) gpm (lpm) Fluid Inlet in. [npsm (m)] 1 1 Fluid Outlet in. [npsm (m)] 1/2 1/2 Hose Connection [npt (f)] 1/2 1/2 Cycles per gallon (l) (paint) Dimensions and Weight Length (handle bar retracted) in. (cm) Width in. (cm) Height (handle bar retracted) in. (cm) Weight lb (kg) Sound Levels (Measured at maximum normal load conditions) Engine HP Sound Pressure db(a) Sound Power db(a) Maximum back fuse rating for EH300DI: Fuse type am: 63 A Fuse type gl: 80 A NOTE: Under voltage release coil in motor starter for EH300DI will not energize if voltage is less than 85% of listed voltage in Technical Data table. Under voltage release coil in motor starter for EH300DI will de-energize and sprayer will stop if voltage drops to 85% of rated nominal voltage. Voltage will need to be increased and sprayer will need to be restarted. NOTE: To operate the EH300DI (24M056) sprayer with a generator, the generator must be sized for 15 kw output (minimum). Basic Sprayer Wetted Parts: Zinc and nickel-plated carbon steel, stainless steel, PTFE, acetal, chrome plating, leather, V-Max UHMWPE, aluminum, tungsten carbide, ceramic, nylon 3A2247A 33

34 Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco s written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco. This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation. THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. Graco s sole obligation and buyer s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale. GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties. In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise. FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées. Graco Information For the latest information about Graco products, visit TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. Original instructions. This manual contains English. MM 3A2247 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. AND SUBSIDIARIES P.O. BOX 1441 MINNEAPOLIS MN USA Copyright 2011, Graco Inc. All Graco manufacturing locations are registered to ISO Revision A - 02/2012

Pro Shot Grease Dispense Valve

Pro Shot Grease Dispense Valve Instructions Parts List Pro Shot Grease Dispense Valve 309032J For high pressure grease dispense. 8000 psi (55 MPa, 552 bar) Maximum Working Pressure Model No. 242055, Series B, 1/4 npt Fluid Inlet Model

More information

RS Gun Front Adapter Kits

RS Gun Front Adapter Kits Kit Instructions RS Gun Front Adapter Kits 332520A EN For adapting the internal mix gun for specific field applications. For professional use only. Important Safety Instructions Read all warnings and instructions

More information

Fuel Meter. Instructions - Parts List. Contents B. Model , measures in gallons Model , measures in liters. For metering fuels.

Fuel Meter. Instructions - Parts List. Contents B. Model , measures in gallons Model , measures in liters. For metering fuels. Instructions - Parts List Fuel Meter 311309B For metering fuels. 80 psi (0.55 MPa, 5.5 bar) Maximum Working Pressure Model 260405, measures in gallons Model 260414, measures in liters Important Safety

More information

Model For petroleum products and other fluids compatible with aluminum and buna-n seals.

Model For petroleum products and other fluids compatible with aluminum and buna-n seals. Instructions - Parts List Piston Hand Pump 311308C Model 260407 For petroleum products and other fluids compatible with aluminum and buna-n seals. Model 260406 For herbicides and other chemicals or fluids

More information

Pressurized oil drain for collection of used lubricants and anti-freeze.

Pressurized oil drain for collection of used lubricants and anti-freeze. Instructions - Parts List 24-Gallon (90-Liter) Oil Ace 30864B Pressurized oil drain for collection of used lubricants and anti-freeze. Model 9577 Series A 8 psi (55 kpa,5 bar) Maximum Working Pressure

More information

Displacement Pump. Instructions C EN. Model psi (3.7 MPa, 37 bar) Maximum Working Pressure 12 gpm Flow Rate

Displacement Pump. Instructions C EN. Model psi (3.7 MPa, 37 bar) Maximum Working Pressure 12 gpm Flow Rate Instructions Displacement Pump 308486C EN For use with petroleum-based lubricants only. For professional use only. Model 237527 540 psi (3.7 MPa, 37 bar) Maximum Working Pressure 12 gpm Flow Rate Important

More information

Field Sensitive Magnetic Proximity Cycle Switch

Field Sensitive Magnetic Proximity Cycle Switch Instructions Field Sensitive Magnetic Proximity Cycle Switch 3A0884A EN Bulletin 15600 4-pin micro FSM proximity switch use with MX, MXP & MGO Valve sections. Dry contact, ceramic magnet proximity switch

More information

Repair D EN. Displacement Pump. Model , Series A 190ES/ 210ES, 190LTS/210LTS Pro 230ES, Pro 270ES Pro 270GS

Repair D EN. Displacement Pump. Model , Series A 190ES/ 210ES, 190LTS/210LTS Pro 230ES, Pro 270ES Pro 270GS Repair Displacement Pump 312015D EN Model 255198, Series A 190ES/ 210ES, 190LTS/210LTS Pro 230ES, Pro 270ES Pro 270GS Maximum Working Pressure 3300 psi (223 bar, 23 MPa) Important Safety Instructions Read

More information

Vertical Hydraulic Driver

Vertical Hydraulic Driver Repair-Parts Vertical Hydraulic Driver 3A001C EN For use with a vertically mounted proportioning pump. For professional use only. D30 - Vertical Hydraulic Driver 100 psi (8. MPa, 8.7 bar) Maximum Working

More information

Pressure Roller with 24-inch Fixed Extension - For application of architectural paints and coatings -

Pressure Roller with 24-inch Fixed Extension - For application of architectural paints and coatings - Instructions Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. 311082D Pressure Roller with 24-inch Fixed Extension - For application of architectural

More information

Universal Hand Pump. Instructions D EN. - For transferring grease to Grease Jockey and G3 Systems - Part No Hand Operated - 35# Pump

Universal Hand Pump. Instructions D EN. - For transferring grease to Grease Jockey and G3 Systems - Part No Hand Operated - 35# Pump Instructions Universal Hand Pump 31758D EN - For transferring grease to Grease Jockey and G3 Systems - Part No. 47886 Hand Operated - 35# Pump 600 psi (4.13 MPa, 41.3 bar) Maximum Working Pressure 85 ml

More information

Merkur Displacement Pump

Merkur Displacement Pump Repair/Parts Merkur Displacement Pump 32792G EN For use with high-performance finishing and coating pumps in hazardous and non-hazardous locations. For professional use only. Important Safety Instructions

More information

Low Pressure Fluid Filters

Low Pressure Fluid Filters Instructions - Parts List Low Pressure Fluid Filters 311775D EN For filtering large volumes of industrial paints and other industrial fluids. For professional use only. See page 3 for model numbers. 500

More information

Horizontal Hydraulic Driver

Horizontal Hydraulic Driver Repair-Parts Horizontal Hydraulic Driver 3A000A ENG For use with two horizontally mounted proportioning pumps. For professional use only. Not for use in explosive atmospheres. 5877 - Horizontal Hydraulic

More information

Instructions 3A4793B EN. See page 3 for a complete list of model descriptions and part numbers.

Instructions 3A4793B EN. See page 3 for a complete list of model descriptions and part numbers. Instructions Variable Frequency Drives 3A4793B EN Variable frequency drives (VFDs) to power and control electric motor driven agitators. For professional use only. Not approved for use in explosive atmospheres

More information

15H882 Slider Bearing Kit

15H882 Slider Bearing Kit Instructions 15H882 Slider Bearing Kit 311616D ENG To replace slider bearings on E-Flo 4-Ball Piston Pumps. For professional use only. Important Safety Instructions Read all warnings and instructions in

More information

Stainless Steel 1000cc Lower

Stainless Steel 1000cc Lower Instructions - Parts List Stainless Steel 1000cc Lower 311716C ENG Designed for low to medium pressure, medium volume circulation of finishing materials. For professional use only. Not approved to European

More information

Stainless Steel Air Motor Conversion Kits

Stainless Steel Air Motor Conversion Kits Instructions Stainless Steel Air Motor Conversion Kits 096D Conversion Kit 650 For 00 Pumps Conversion Kit 65 For 590 Pumps Conversion Kit 65 For 50 Pumps Model 650 Model 65 Model 65 Installation Pressure

More information

Pump Package Conversion Kits

Pump Package Conversion Kits Instructions - Parts Pump Package Conversion Kits A0B ENG To install an L00CM or L500CM Check-Mate Displacement Pump on an existing motor. For professional use only. Not for use in explosive atmospheres.

More information

PROVEN QUALITY, LEADING TECHNOLOGY

PROVEN QUALITY, LEADING TECHNOLOGY Instructions Parts List Fluid Outlet Filter 303Z For filtering of finishing materials. For professional use only. Important Safety Instructions Read all warnings and instructions in this manual. Save these

More information

Displacement Pump. Repair-Parts. Contents D ENG. Part No psi (13.8 MPa, 138 bar) Maximum Working Pressure

Displacement Pump. Repair-Parts. Contents D ENG. Part No psi (13.8 MPa, 138 bar) Maximum Working Pressure Repair-Parts Displacement Pump 313383D ENG For use with polyurethane foam, polyurea, and similar non-flammable material. For professional use only. Not for use in explosive atmospheres. Part No. 257344

More information

Old Proportioning Pumps

Old Proportioning Pumps Repair - Parts Old Proportioning Pumps 311391F For proportioning pumps on Gusmer and Old Graco H-25 and H-XP2 Hydraulic Proportioners. Important Safety Instructions Read all warnings and instructions in

More information

Motor Mounting Kits. Instructions J EN. 16C487 Motor Coupler Kit includes 2.25 in. (57.2 mm) key For NEMA 182/184 TC Frame ATEX Electric Motors

Motor Mounting Kits. Instructions J EN. 16C487 Motor Coupler Kit includes 2.25 in. (57.2 mm) key For NEMA 182/184 TC Frame ATEX Electric Motors Instructions Motor Mounting Kits 31160J EN To install electric motors on E-Flo 4-Ball Piston Pumps. For professional use only. (Kits do not include motors.) 16C487 Motor Coupler Kit includes 2.2 in. (7.2

More information

Pump/Manifold Kits. Instructions F ENG. To convert E-Flo 4-Ball Piston Pumps to a different size lower. For professional use only.

Pump/Manifold Kits. Instructions F ENG. To convert E-Flo 4-Ball Piston Pumps to a different size lower. For professional use only. Instructions Pump/Manifold Kits 311611F ENG To convert E-Flo 4-Ball Piston Pumps to a different size lower. For professional use only. See page 2 for a list of available kits. Important Safety Instructions

More information

INSTRUCTIONS PARTS LIST

INSTRUCTIONS PARTS LIST INSTRUCTIONS PARTS LIST 30812 This manual contains important warnings and information. READ AND RETAIN FOR REFERENCE See manual 308393 for complete gun washer warnings and instructions. Rev. B AIR SPRAY

More information

Electronic Pulse Meters

Electronic Pulse Meters Instructions - Parts List Electronic Pulse Meters 308245P EN For use with petroleum-based lubricants only. 1500 psi (10.3 MPa, 103 bar) Maximum Working Pressure EFC (Electronic Fluid Commander): Model

More information

Instructions-Parts 3A2801G. See page 2 for model part numbers, maximum fluid working pressure, and approvals.

Instructions-Parts 3A2801G. See page 2 for model part numbers, maximum fluid working pressure, and approvals. Instructions-Parts Mix Manifold Kit 3A2801G EN For at-the the-gun mixing of 2 component materials when used with a ProMix PD2K Proportioner. For professional use only. Important Safety Instructions Read

More information

Single Acting and Double Acting Paint Spray Guns for RoadLazer RoadPak Line Striping System

Single Acting and Double Acting Paint Spray Guns for RoadLazer RoadPak Line Striping System Instructions Single Acting and Double Acting Paint Spray Guns for RoadLazer RoadPak Line Striping System 308613H EN - For the application of road marking paints and coatings - - For professional use only

More information

24G621 Agitator Speed Controller Accessory

24G621 Agitator Speed Controller Accessory Instructions-Parts 24G62 Agitator Speed Controller Accessory 3A35A ENG Accessory kit to control and automatically maintain the speed of an air-powered agitator. For professional use only. Important Safety

More information

Stainless Steel Air Motor Conversion Kits

Stainless Steel Air Motor Conversion Kits Instructions Stainless Steel Air Motor Conversion Kits 096B Conversion Kit 650 For 00 Pumps Conversion Kit 65 For 590 Pumps Conversion Kit 65 For 50 Pumps Model 650 Model 65 Model 65 Graco Inc. P.O. Box

More information

Color Change Valve. Instructions Parts List K

Color Change Valve. Instructions Parts List K Instructions List Color Change Valve 0K For color changing or distribution of industrial paints and coatings or fluids. 00 psi (0. MPa, bar) Maximum Air Inlet Pressure 00 psi (. MPa, bar) Maximum Fluid

More information

390 Airless Sprayer. Parts J EN. Models: , , , , , ,262024, , , , Hi-Boy.

390 Airless Sprayer. Parts J EN. Models: , , , , , ,262024, , , , Hi-Boy. Parts 390 Airless Sprayer 37J EN Models: 253958, 254998, 2209, 25498, 25499, 2539,22024, 2539, 25392, 2548, 82084 Important Safety Instructions Read all warnings and instructions in the Operation and Repair

More information

950SeriesSealantGun. Instructions-Parts D. Models Palm Grip Gun: Pistol Grip Gun: ENG

950SeriesSealantGun. Instructions-Parts D. Models Palm Grip Gun: Pistol Grip Gun: ENG Instructions-Parts 950SeriesSealantGun 309968D ENG For dispensing sealant from caulking tubes. For professional use only. Important Safety Instructions Read all warnings and instructions in this manual.

More information

Hose Heat Control Kit

Hose Heat Control Kit Instructions - Parts 248921 Hose Heat Control Kit 310798D For monitoring and controlling fluid temperature in low voltage heated hose. Not for use in explosive atmospheres. Important Safety Instructions

More information

Ultimate Mx II. Parts List E psi (228 bar, 22.8 MPa) Maximum Working Pressure. Vac Model Type Lo-Boy Hi-Boy. Sherwin Williams 120V

Ultimate Mx II. Parts List E psi (228 bar, 22.8 MPa) Maximum Working Pressure. Vac Model Type Lo-Boy Hi-Boy. Sherwin Williams 120V Parts List Ultimate Mx II 3437E 3300 psi (228 bar, 228 MPa) Maximum Working Pressure Vac Model Type Lo-Boy Hi-Boy Sherwin Williams 20V Sherwin Williams 20V 695 Standard 826068 826067 Premium 826070 826069

More information

Instructions Parts List

Instructions Parts List Instructions Parts List WITH OR WITHOUT ELECTRONIC METERS V5 V12 EM6 and EM12Dispense Valves 308642N For dispense of petroleum and synthetic based oils. 1500 psi (10 MPa, 102 bar) Maximum Working Pressure

More information

Operation. GMAX II 3900/5900/5900HD/5900 Convertible/7900 TexSpray 5900HD Convertible/7900HD Airless Sprayers 3A0242B

Operation. GMAX II 3900/5900/5900HD/5900 Convertible/7900 TexSpray 5900HD Convertible/7900HD Airless Sprayers 3A0242B Operation GMAX II 3900/5900/5900HD/5900 Convertible/7900 TexSpray 5900HD Convertible/7900HD Airless Sprayers - For Portable Airless Spraying of Architectural Coatings and Paints - 3300 psi (22.8 MPa, 228

More information

310820H EN. 390 Electric Airless Sprayers. Operation. - For portable spray applications of architectural paints and coatings - Hi-Boy ProStep

310820H EN. 390 Electric Airless Sprayers. Operation. - For portable spray applications of architectural paints and coatings - Hi-Boy ProStep Operation 390 Electric Airless Sprayers 310820H EN - For portable spray applications of architectural paints and coatings - 3300 psi (227 bar, 22.7 MPa) Maximum Working Pressure Important Safety Instructions

More information

Displacement Pump Used in the Ultra Max 695 Sprayers 3000 psi (207 bar, 21 MPa) MAXIMUM WORKING PRESSURE

Displacement Pump Used in the Ultra Max 695 Sprayers 3000 psi (207 bar, 21 MPa) MAXIMUM WORKING PRESSURE INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. 308815 Rev. J Displacement Pump Used in the Ultra Max 695 Sprayers 3000 psi (207

More information

EH 200 HDI Hydraulic Sprayer

EH 200 HDI Hydraulic Sprayer Repair EH 200 HDI Hydraulic Sprayer 312159A 230 Vac, 50 Hz, 14A - Use with Architectural Coatings and Paints - 3300 psi (2.8 MPa, 230 bar) Maximum Working Pressure Model: 253581 Sprayer Model: 255094 Sprayer,

More information

Displacement Pump INSTRUCTIONS-PARTS LIST psi (250 bar, 24.8 MPa) Maximum Working Pressure Model , Series A. Model , Series A

Displacement Pump INSTRUCTIONS-PARTS LIST psi (250 bar, 24.8 MPa) Maximum Working Pressure Model , Series A. Model , Series A INSTRUCTIONS-PARTS LIST 309277 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. First choice when quality counts. Rev. B Displacement Pump 3600 psi (250

More information

3600 psi (250 bar, 24.8 MPa) Maximum Working Pressure Model , Series A Ultra Max II and Ultimate Mx II 695 and 795

3600 psi (250 bar, 24.8 MPa) Maximum Working Pressure Model , Series A Ultra Max II and Ultimate Mx II 695 and 795 Repair Displacement Pump 310643H 3600 psi (250 bar, 24.8 MPa) Maximum Working Pressure Model 248204, Series A Ultra Max II and Ultimate Mx II 695 and 795 Model 248205, Series A Ultra Max II and Ultimate

More information

Model , Series A 9 in. (23 cm) roller frame with 45 angle and 12 in. reach 1/2 in. (13 mm) nap roller cover

Model , Series A 9 in. (23 cm) roller frame with 45 angle and 12 in. reach 1/2 in. (13 mm) nap roller cover Operating Instructions 309899 Rev. A This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. INSTRUCTIONS Manufactured by Model 246818, Series A 9 in. (23 cm) roller frame

More information

ST Max 395/495/595 ST Max II 490/495/595

ST Max 395/495/595 ST Max II 490/495/595 Parts ST Max 395/495/595 ST Max II 490/495/595 309706P EN For professional use only. 3300 psi (22.8 MPa, 228 bar) Maximum Working Pressure See page 2 for model information. Important Safety Instructions

More information

Cleaning System. Instructions/Parts A

Cleaning System. Instructions/Parts A Instructions/Parts Cleaning System 310623A 234533 For use with Multi-Orifice Linear Streaming Applicator (MOLSA) to apply automotive Liquid Applied Sound Deadener (LASD) materials. 100 psi (0.68 MPa, 6.8

More information

4:1 Fusion Static Mixer Kit

4:1 Fusion Static Mixer Kit Instructions-Parts 4:1 Fusion Static Mixer Kit 1294A For use with 4:1 ratio material and Graco Fusion MP gun only. Not for use in explosive atmospheres. 500 psi (24.5 MPa, 245 bar) Maximum Fluid Working

More information

DISPLACEMENT PUMP INSTRUCTIONS-PARTS LIST Rev. K. Model , Series A Model , Series B Model , Series A

DISPLACEMENT PUMP INSTRUCTIONS-PARTS LIST Rev. K. Model , Series A Model , Series B Model , Series A INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. DISPLACEMENT PUMP 308190 Rev. K 3000 psi (210 bar) MAXIMUM WORKING PRESSURE Model

More information

ProMix Auto Color and Catalyst Change Kits

ProMix Auto Color and Catalyst Change Kits Installation - Parts ProMix Auto Color and Catalyst Change Kits 311396C EN For proportional mixing of plural component coatings. For professional use only. See page 2 for kit information. Important Safety

More information

Carbon Steel 1000cc Lower

Carbon Steel 1000cc Lower Instructions - Parts List Carbon Steel 000cc Lower 377E ENG Designed for low to medium pressure, medium volume circulation of finishing materials. For professional use only. Not approved to European explosive

More information

Fast-Flo Air Motor 12.5 bar (1.25 MPa, 180 psi) Maximum Air Working Pressure

Fast-Flo Air Motor 12.5 bar (1.25 MPa, 180 psi) Maximum Air Working Pressure 03652 Instructions Parts List Fast-Flo Air Motor 12.5 bar (1.25 MPa, 180 psi) Maximum Air Working Pressure 307456S Model 215963, Series A 101.6 mm (4 in.) stroke NOTE: To replace Air Motor 215963, order

More information

Elevators and Pump Supports

Elevators and Pump Supports Instructions Parts List Elevators and Pump Supports 306287V Used to raise and lower select Graco circulation and supply pumps. For professional use only. 200 psi (.4 MPa, 4 bar) Maximum Air Input Pressure

More information

Spray Nozzle Adapters

Spray Nozzle Adapters INSTRUCTIONS-PARTS LIST 306 788 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. First choice when quality counts. Rev. G Supersedes Rev. F DIRECTIONAL

More information

SaniForce Air Motors. Instructions/Parts 3A1211N

SaniForce Air Motors. Instructions/Parts 3A1211N Instructions/Parts SaniForce Air Motors 3A2N EN For use on SaniForce piston pumps, which are used to transfer medium to high viscosity fluids in applications requiring high sanitation. For professional

More information

Displacement Pump 3600 psi (250 bar, 24.8 MPa) Maximum Working Pressure Model , Series A

Displacement Pump 3600 psi (250 bar, 24.8 MPa) Maximum Working Pressure Model , Series A INSTRUCTIONS-PARTS LIST 309277 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. First choice when quality counts. Rev. M Displacement Pump 3600 psi (250

More information

Integrated and 2-Button Interlock Air Controls for use with Supply Systems.

Integrated and 2-Button Interlock Air Controls for use with Supply Systems. Instructions-Parts Air Controls 312374A Integrated and 2-Button Interlock Air Controls for use with Supply Systems. Important Safety Instructions Read all warnings and instructions in this manual. Save

More information

Mechanical Pulse Meter

Mechanical Pulse Meter Instructions Parts List Mechanical Pulse Meter Part No. 215474 Measures in pints, quarts, and gallons 308847D Part No. 215475 Measures in liters For antifreeze or oil. Sends 10 pulses per quart (11 pulses

More information

Air Actuated Dispense Valve

Air Actuated Dispense Valve Instructions-Parts Air Actuated Dispense Valve 312782B To dispense plural component fluids and solvents. Part No. 15X303 High Pressure Dispense Valve 3000 psi (21 MPa, 210 bar) Maximum Fluid Working Pressure

More information

RAZOR Siphon Feed Gun

RAZOR Siphon Feed Gun Instructions - Parts List RAZOR Siphon Feed Gun 312106G EN A premier gun for the automotive refinish market for use with thin to medium viscosity materials (14-20 seconds Zahn #2 cup). If spraying heavier

More information

Displacement Pump. Repair-Parts. Contents B EN. Part No psi (22.7 MPa, 227 bar) Maximum Working Pressure

Displacement Pump. Repair-Parts. Contents B EN. Part No psi (22.7 MPa, 227 bar) Maximum Working Pressure Repair-Parts Displacement Pump 313123B EN For use with polyurethane foam, polyurea, and similar non-flammable material. Not for use in explosive atmospheres. Part No. 2577 3300 psi (22.7 MPa, 227 bar)

More information

Dura-Flo Lowers A

Dura-Flo Lowers A Instructions - Parts Dura-Flo Lowers 311825A Carbon Steel or Stainless Steel Lowers, with Severe-Duty Rod and Cylinder Dura-Flo 1800 (430 cc) Lowers Dura-Flo 2400 (580 cc) Lowers Important Safety Instructions

More information

Displacement Pump 3600 psi (250 bar, 24.8 MPa) Maximum Working Pressure Model , Series A

Displacement Pump 3600 psi (250 bar, 24.8 MPa) Maximum Working Pressure Model , Series A INSTRUCTIONS-PARTS LIST 308798 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. First choice when quality counts. Rev. U Displacement Pump 3600 psi (250

More information

Instructions Parts List. Table of Contents F. Part No Part No

Instructions Parts List. Table of Contents F. Part No Part No Instructions Parts List PrecisionFlo XL Metering Valve For use when dispensing fluids that meet at least one of the following conditions for non-flammability: The fluid has a flash point above 140F (60C)

More information

Air Actuated Dispense Valve

Air Actuated Dispense Valve Instructions-Parts Air Actuated Dispense Valve 312782D EN To dispense plural component fluids and solvents. For professional use only. Part No. 15X303 High Pressure Dispense Valve 3000 psi (21 MPa, 207

More information

Husky 515/Husky 716 Drum Pump Kits and Packages

Husky 515/Husky 716 Drum Pump Kits and Packages C/ Maximiliano Thous, 22B. 46009, Valencia (España) Tlf: 902 304 36 Fax: 902 876 377 www.quilinox.com quilinox@quilinox.com Husky 55/Husky 76 Drum Pump Kits and Packages 3096D Important Safety Instructions

More information

XHF Spray Gun. Instructions - Parts 3A2799A EN. Part No , Series A

XHF Spray Gun. Instructions - Parts 3A2799A EN. Part No , Series A Instructions - Parts XHF Spray Gun 3A2799A EN For spraying viscous materials at high flow rates. For professional use only. Part No. 262854, Series A Includes an XHD RAC Guard and XHD429 SwitchTip 7250

More information

Split Manifold Kits. Installation Parts List C. Converts Husky 307 Diaphragm Pump to dual fluid inlet or outlet

Split Manifold Kits. Installation Parts List C. Converts Husky 307 Diaphragm Pump to dual fluid inlet or outlet Installation Parts List Split Manifold Kits 0849C Converts Husky 07 Diaphragm Pump to dual fluid inlet or outlet Part No. 2720 For Husky 07 Polypropylene Pumps Part No. 272 For Husky 07 cetal Pumps Important

More information

RoadLazer Skid-Mount OEM Striping Package

RoadLazer Skid-Mount OEM Striping Package RoadLazer Skid-Mount OEM Striping Package - For OEM use in customized line striper applications only - 310664D EN Model 234672 Hydraulic Stainless Steel 2000 psi (138 bar) Maximum Working Pressure Read

More information

PROVEN QUALITY. LEADING TECHNOLOGY.

PROVEN QUALITY. LEADING TECHNOLOGY. Instructions Stainless Steel, Air Operated Dispensing Valve 306715M EN 3000 psi (21 MPa, 210 bar) Maximum Working Pressure Model No. 205612, Series B Without seat or fluid needle. Model No. 205435 Includes

More information

Merkur Spray Packages

Merkur Spray Packages Instructions - Parts List Merkur Spray Packages 309463N Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. TI20A TI202A TI203A II 2 G Contents Manual

More information

Mark V Premium and Mark V Max Electric Airless Sprayers

Mark V Premium and Mark V Max Electric Airless Sprayers Parts Mark V Premium and Mark V Max Electric Airless Sprayers 3A2245B EN For Portable Airless Spraying of Architectural Coatings and Paints. For professional use only. Not approved for use in European

More information

Air Regulator 100 psi (.7 MPa, 7 bar) Maximum Air Inlet Pressure

Air Regulator 100 psi (.7 MPa, 7 bar) Maximum Air Inlet Pressure INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. First choice when quality counts. 30934 Rev. A Air Regulator 00 psi (.7 MPa, 7

More information

Dura-Flo Lowers. Instructions - Parts F ENG. Dura-Flo 1800 (430 cc) Lowers Dura-Flo 2400 (580 cc) Lowers

Dura-Flo Lowers. Instructions - Parts F ENG. Dura-Flo 1800 (430 cc) Lowers Dura-Flo 2400 (580 cc) Lowers Instructions - Parts Dura-Flo Lowers 3825F ENG Carbon Steel or Stainless Steel Lowers, with Severe-Duty Rod and Cylinder. Dura-Flo 800 (430 cc) Lowers Dura-Flo 2400 (580 cc) Lowers Important Safety Instructions

More information

Zip-Tex Spray Gun. Instructions A. Model psi (0.86 MPa, 8.6bar) Maximum Working Pressure

Zip-Tex Spray Gun. Instructions A. Model psi (0.86 MPa, 8.6bar) Maximum Working Pressure Instructions Zip-Tex Spray Gun 311159A - For water-based materials only - (Consult your material supplier for Warnings and Application Requirements) Model 249458 125 psi (0.86 MPa, 8.6bar) Maximum Working

More information

NXT Air Motor for FRP

NXT Air Motor for FRP Instructions - Parts NXT Air Motor for FRP AB EN For use with composites in hazardous or non-hazardous locations. For professional use only. Model M0LNL 00 psi (0. MPa,.0 bar) Maximum Working Pressure

More information

Airless Spray Gun. Instructions Parts List H. Model , Series H psi (21.0 MPa, 210 bar) Maximum Working Pressure

Airless Spray Gun. Instructions Parts List H. Model , Series H psi (21.0 MPa, 210 bar) Maximum Working Pressure Instructions Parts List Airless Spray Gun 306796H Model 206408, Series H 3000 psi (21.0 MPa, 210 bar) Maximum Working Pressure Important Safety Instructions Read all warnings and instructions in this manual.

More information

Mark V Premium, Mark V Max, Mark VII Max, Mark X Premium, and Mark X Max Electric Airless Sprayers

Mark V Premium, Mark V Max, Mark VII Max, Mark X Premium, and Mark X Max Electric Airless Sprayers Operation Mark V Premium, Mark V Max, Mark VII Max, Mark X Premium, and Mark X Max Electric Airless Sprayers 3A2243B EN For Portable Airless Spraying of Architectural Coatings and Paints. For professional

More information

Lubricator Gun: 10,000 psi (700 bar) Maximum Delivery Pressure when disconnected from Dispenser

Lubricator Gun: 10,000 psi (700 bar) Maximum Delivery Pressure when disconnected from Dispenser INSTRUCTIONS-PARTS LIST 30 455 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Rev. C Supercedes B Hand-Operated Portable Grease Dispenser Buckshot Luber

More information

Viscount I Hydraulic Motor and Displacement Pump

Viscount I Hydraulic Motor and Displacement Pump INSTRUCTIONS-PARTS LIST 308 674 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Rev. C Supersedes Rev. B Viscount I Hydraulic Motor and Displacement Pump

More information

GH 130, GH 200, GH 230, GH 300 Hydraulic Sprayers

GH 130, GH 200, GH 230, GH 300 Hydraulic Sprayers Repair GH 130, GH 200, GH 230, GH 300 Hydraulic Sprayers 311797N EN - Use with Architectural Coatings and Paints - For professional use only. Not approved for use in explosive atmosphere locations 3300

More information

INSTRUCTIONS-PARTS LIST. BLACK MAX Airless Spray Gun psi (24.8 MPa, 248 bar) Maximum Working Pressure. Rev. F Supersedes D and PCN E

INSTRUCTIONS-PARTS LIST. BLACK MAX Airless Spray Gun psi (24.8 MPa, 248 bar) Maximum Working Pressure. Rev. F Supersedes D and PCN E INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. First choice when quality counts. 307 821 Rev. F Supersedes D and PCN E BLACK

More information

Proportioning pumps and hydraulic cylinders used on Hydraulic Proportioners. Model : 2000 psi (13.8 MPa, 138 bar) Maximum Working Pressure

Proportioning pumps and hydraulic cylinders used on Hydraulic Proportioners. Model : 2000 psi (13.8 MPa, 138 bar) Maximum Working Pressure - Parts Proportioning Pumps 3068F Proportioning pumps and hydraulic cylinders used on Hydraulic Proportioners. Important Safety Instructions Read all warnings and instructions in this manual and in manuals

More information

Split Manifold Kits. Installation - Parts List D. Converts Huskyt 307 Diaphragm Pump to dual fluid inlet or outlet

Split Manifold Kits. Installation - Parts List D. Converts Huskyt 307 Diaphragm Pump to dual fluid inlet or outlet Installation - Parts List Split Manifold Kits 0849D Converts Huskyt 07 Diaphragm Pump to dual fluid inlet or outlet Part No. 2720 For Husky 07 Polypropylene Pumps Part No. 272 For Husky 07 cetal Pumps

More information

Ultra Platinum Sprayers

Ultra Platinum Sprayers Parts Ultra Platinum Sprayers 313565F EN For Portable Airless Spraying of Architectural Coatings and Paints. For professional use only. Not approved for use in European explosive atmosphere locations.

More information

LUBRICATOR GUN INSTRUCTIONS-PARTS LIST. 10,000 psi (700 bar) Maximum Delivery Pressure. Detachable-type

LUBRICATOR GUN INSTRUCTIONS-PARTS LIST. 10,000 psi (700 bar) Maximum Delivery Pressure. Detachable-type INSTRUCTIONS-PARTS LIST 306 460 INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Rev. E Supercedes D Detachable-type LUBRICATOR GUN 10,000 psi (700 bar)

More information

Texture Gun & Hopper B

Texture Gun & Hopper B Operation and Parts Texture Gun & Hopper 309584B For Water-Based Materials Only Model 245924 100 psi (7 bar, 0.7 MPa) Maximum Working Air Pressure 60 psi (4.1 bar, 0.41 MPa) Maximum Working Fluid Pressure

More information

Old Seal Kits. Instructions - Parts B. Piston Seal Kits, see page 2. Cylinder Seal Kits for A-Side Pumps, see page 2

Old Seal Kits. Instructions - Parts B. Piston Seal Kits, see page 2. Cylinder Seal Kits for A-Side Pumps, see page 2 Instructions - Parts Old Seal Kits 32348B To replace proportioning pump piston seal sets or cylinder seal sets used on Gusmer and Old Graco H-25 and H-XP2 Hydraulic Proportioners. Important Safety Instructions

More information

Pistol Grip Mastic Flo Gun

Pistol Grip Mastic Flo Gun Instructions Parts List Pistol Grip Mastic Flo Gun 308206E For spraying highly filled texture materials. 4050psi (27.6 MPa, 276 bar) Maximum Working Pressure Model 224990, Series A; Model 289670 With Diffuser,

More information

Displacement Pump. FOR USE WITH REACTOR ELECTRIC PROPORTIONERS 3500 psi (24.5 MPa, 245 bar) Maximum Working Pressure

Displacement Pump. FOR USE WITH REACTOR ELECTRIC PROPORTIONERS 3500 psi (24.5 MPa, 245 bar) Maximum Working Pressure Repair - Parts Displacement Pump 309577G FOR USE WITH REACTOR ELECTRIC PROPORTIONERS 3500 psi (4.5 MPa, 45 bar) Maximum Working Pressure Component A (ISO) Pumps with wet-cup flush feature Part No. 46830,

More information

Airless Spray Gun INSTRUCTIONS DP psi (345 bar) Maximum Working Pressure

Airless Spray Gun INSTRUCTIONS DP psi (345 bar) Maximum Working Pressure INSTRUCTIONS DP-6376 Airless Spray Gun 5000 psi (345 bar) Maximum Working Pressure INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Table of Contents Warnings......................................

More information

Water Sandblaster Kit

Water Sandblaster Kit a Instructions - Parts List Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. Water Sandblaster Kit 308544 - For suction fed injection of sand into

More information

Instructions Parts List

Instructions Parts List Instructions Parts List DOUBLE ACTING Falcon and Falcon II Air Motors 08995E Part No. 41504, Series C Falcon Air Motor 150 psi (1.0 MPa, 10 bar) Maximum Air Input Pressure Part No. 41505, Series C Falcon

More information

INSTRUCTIONS-PARTS LIST

INSTRUCTIONS-PARTS LIST INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. First choice when quality counts. 307 620 Rev. M Supersedes J and PCN K PORTABLE

More information

High-Flo Lowers. Instructions - Parts List M ENG

High-Flo Lowers. Instructions - Parts List M ENG Instructions - Parts List High-Flo Lowers 3690M ENG Designed for low pressure, medium volume circulation of finishing materials. For professional use only. Important Safety Instructions Read all warnings

More information

UltraMix Pumps. Repair - Parts A

UltraMix Pumps. Repair - Parts A Repair - Parts UltraMix Pumps 310671A Read warnings and instructions. See page 3 for model information, including maximum working pressure and approvals. TI4598a Graco Inc. P.O. Box 1441 Minneapolis, MN

More information

MGFHVLP. Instructions/Parts. Mini Gravity Feed System E. Part No Includes MGFHVLP Mini Gravity Feed Spray Gun and MGC 125 Gravity Cup.

MGFHVLP. Instructions/Parts. Mini Gravity Feed System E. Part No Includes MGFHVLP Mini Gravity Feed Spray Gun and MGC 125 Gravity Cup. Instructions/Parts MGFHVLP Mini Gravity Feed System FOR PRODUCT INFORMATION CALL: 1-800-742-7731 309989E For gravity feed spraying of automotive colors and clears. Ideal for touch-up and detail work. Important

More information

Plus Mark V Mark V Plus

Plus Mark V Mark V Plus Parts List Ultra Max II 3363K ENG 3300 psi (228 bar, 228 MPa) Maximum Working Pressure Vac Model Lo-Boy Hi-Boy 240 Europe 240 Europe Multi-cord 240 Asia 695 25534 249663 795 249666 25349 795 Plus 25665

More information

695 Standard Premium Standard Premium Standard * Premium *

695 Standard Premium Standard Premium Standard * Premium * Repair Ultimate Mx II 695/795/1095/1595 Airless Sprayers 3300 psi (227 bar, 22.7 MPa) Maximum Working Pressure 309942 Rev. F Vac Model Standard/ Premium 695 Standard 826048 826047 Premium 826041 826040

More information

Instructions/Parts List

Instructions/Parts List Instructions/Parts List FOR 2: RATIO STANDARD PUMPS Standard Air Motor 30785L 80 psi (.25 MPa, 2.5 bar) Maximum Air Working Pressure Model 204464, Series B For Pump Model 204456 Model 204722, Series C

More information

President Pump WITH PRIMING PISTON

President Pump WITH PRIMING PISTON Instructions Parts List President Pump WITH PRIMING PISTON 306746K 24:1 Ratio Models 4320 psi (29.8 MPa, 298 bar) Maximum Fluid Working Pressure Part No. 205791, Series E 5 & 10 gallon (19 & 38 liter)

More information

Repair. GH 200, GH 230, GH 300; Series A & B EH 200, Series A Hydraulic Sprayers P. - Use with Architectural Coatings and Paints -

Repair. GH 200, GH 230, GH 300; Series A & B EH 200, Series A Hydraulic Sprayers P. - Use with Architectural Coatings and Paints - ti5380a Repair GH 200, GH 230, GH 300; Series A & B EH 200, Series A Hydraulic Sprayers ti5380a 310778P EN - Use with Architectural Coatings and Paints - 3300 psi (2.8 MPa, 228 bar) Maximum Working Pressure

More information