TIPSTER ELECTRICAL/HYDRAULIC INSTALLATION GUIDELINES 2DAK HOIST
|
|
- Milo Quentin Burke
- 5 years ago
- Views:
Transcription
1 Note: It is recommended that protective glasses be worn during installation. At no time should anyone be underneath the Tipster without using a proper safety device. When drilling holes into the pick-up bed or dash, care must be taken to ensure no wires or hoses are damaged. Installation Instructions 1. A. Remove the tailgate of pick-up truck including the hardware. B. Certain trucks may need to have the bumper lowered in order to have the tailgate work properly. C. Remove any obstructions off rear floor vertical face of pick-up truck (light clusters, etc.) 2. Drill two 11/16 or 5/8 holes in the bottom of the pick-up bed near the front right hand side, as shown. Insert provided grommets into the holes. TAILGATE CAB A CAB DETAIL A 1.00 HOLES FOR CABLES DRAWING #: D10136 PAGE 1 OF 7 ISSUE DATE: 07DEC2009
2 3. Place the tipster into the pick-up bed. Leave some space at the front for easy access. DUMP VALVE SOLENOID 4. Remove the front retaining bolt and nut holding the Tipster body to the frame, located at bottom right hand side of the hoist (see picture bellow). Removing bolt will allow the body to dump. HOIST A FRONT RETAINING BOLT DETAIL A DRAWING #: D10136 PAGE 2 OF 7 ISSUE DATE: 07DEC2009
3 5. Attach the 3 strand cable onto the solenoid as per wiring diagram, and install the provided 30 Amp. fuse holder. BATTERY CABLE 46A CABLE x 2 Ft A 3 STRAND CABLE x15 Ft. WHITE TOGGLE SWITCH BLACK 46A CABLE x 17 Ft. GREEN OR RED DUMP VALVE 30A SOLENOID MOTOR 6. Attach the battery cable onto the solenoid. 7. Feed the battery cable and the 3 strand cable through the holes in the corner of the bed. Use the supplied grommets in the holes to pass the cables. 8. Locate brake light on top bracket and secure with provided hardware. 9. Route wiring through washers in hoist cavity and secure on place. 10. Push the Tipster into the pick-up as far as possible. The rear base angle should be flush against the rear of the pick-up bed. Take care not to pinch or damage wires or cables. DRAWING #: D10136 PAGE 3 OF 7 ISSUE DATE: 07DEC2009
4 11. Drill two holes (1/2 DIA) into the rear of the pick-up bed, through the predrilled holes in the Tipster frame. Watch for wires behind. TIPSTER BODY B PICK-UP BOX O 1/2-2 HOLES THROUGH REAR ANGLE AND PICK-UP BED PICK-UP BED REAR ANGLE-TIPSTER BODY DETAIL B 12. Fasten the Tipster Body using the two bolts (1/2 x 1.50 ), flat washers, lock washers and nuts supplied. (Shims may be required on some units if rear angle does not fit flush to pick-up bed). BOLT (1/2" x 1.50) FLAT WASHER LOCK WASHER NUT(1/2") DRAWING #: D10136 PAGE 4 OF 7 ISSUE DATE: 07DEC2009
5 13. Raise the front of the Tipster either manually or hydraulically. IMPORTANT- BEFORE PROCEEDING MAKE SURE A SAFETY PROP IS USED. SAFETY PROP 14. Drill 2 holes (13/32) through the Tipster front frame into the pick-up floor HOLES DRAWING #: D10136 PAGE 5 OF 7 ISSUE DATE: 07DEC2009
6 15. Bolt the frame to the pick-up floor using the two bolts (3/8 x 1.50), washers and nuts supplied. BOLT (3/8 x 1.50) A NUT FLAT WASHER LOCK WASHER DETAIL A 16. Route the brake light conduit along underside of tipster between the cross members and body, and through the washers on top of the rear mounting angle. 17. Connect to brake logic module as per wiring diagram. 3 RD BRAKE LIGHT CONTROL MODULE TO BE LOCATED IN BODY CAVITY OF LEFT TAILLIGHT OR SIMILAR FOR PROTECTION FROM WEATHER. CONTROL MODULE RIGHT BRAKE/ TURN LEFT BRAKE/ TURN TRUCK BODY DRAWING #: D10136 PAGE 6 OF 7 ISSUE DATE: 07DEC2009
7 18. Run the battery cable and the 3 strand cable through the hole under the pick-up bed to the driver side, along the frame to the engine compartment. Secure the cables adequately to frame of pick-up truck 19. Mark the desired location of the toggle switch in the dashboard. Drill a ½ hole, insert the toggle switch and tighten. Extreme care is required to avoid damage to dash wiring/ or comp. 20. Feed the 3 wire cable up the firewall to the switch in the dash. 21. Use the heat shrink tubing supplied and attach the wires to the toggle switch, as per wiring drawing. Finish the wiring by attaching the battery cable to the positive terminal of the battery (see wiring diagram) through the150a fuse provided. 22. Add Dexron III transmission fluid, if required, below breather cap of reservoir tank with hoist down. IMPORTANT NOTE: The double acting tailgate should be used properly. Use the lower handle on the bottom of the tailgate to open the lower pins when dumping the material. Do not operate the Tipster when the top pins of the tailgate are open. Do not open the tailgate top pins and the tailgate lever (lower pins) simultaneously (see picture below). TIPSTER BODY TAILGATE TOP PIN LOWER HANDLE C PICK-UP BOX LOWER PIN DRAWING #: D10136 PAGE 7 OF 7 ISSUE DATE: 07DEC2009 DETAIL C
650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present
TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present Installing the Base Plate 1. Examine the interior and exterior
More informationand Original Series Pickup Lift Mounting Instructions Fullsize Chevy & GMC Trucks: 1500 & 2500 LD HD & 3500HD BOLT-ON GUSSET
r ve and Original Series Pickup Lift Mounting Instructions Fullsize Chevy & GMC Trucks: 1500 & 2500 LD 1999-2007 2500HD & 3500HD 2000-2007 Preparing the Gate 1. Remove the mounting hardware which is banded
More informationG-170. r ve Pickup Lift Mounting Instructions Fullsize Chevy & GMC Trucks- 1500, 2500 & 3500: 2007-present
Fullsize Chevy & GMC Trucks- 1500, 2500 & 3500: 2007-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting bracket kit (Figure 1 and Table 1). 18-5/8"
More information650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present
TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present Installing the Base Plate 1. Examine the interior
More informationand Original Series Pickup Lift Mounting Instructions Fullsize Nissan Titan Trucks present T-420 BOLT-ON GUSSET PART#5257
and Original Series Pickup Lift Mounting Instructions Fullsize Nissan Titan Trucks- 2004-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting bracket
More informationand Original Series Pickup Lift Mounting Instructions Fleetside Chevy & GMC Trucks Fleetside 4-door Chevy & GMC Trucks T-100
r ve and Original Series Pickup Lift Mounting Instructions Fleetside Chevy & GMC Trucks - 1960-1987 Fleetside 4-door Chevy & GMC Trucks - 1988-1991 Preparing the Gate 1. Remove the mounting hardware which
More informationand Original Series Pickup Lift Mounting Instructions T-150-T T-150 PART#5177 T-150-T
Fullsize Chevy & GMC Trucks- 988-999 Toyota Tundra- 2000-2006 Toyota T-00-993-999 Preparing the Gate r ve and Original Series Pickup Lift Mounting Instructions. Remove the mounting hardware which is banded
More informationSELF DRILL SCREWS FILLER STRIP
r ve Pickup Lift Mounting Instructions Fullsize Ford Trucks- F-150 2015-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting bracket kit (Figure
More informationPatriot. Aluminum and Steel 5spring. Step #1 Tarp Spool with Gear Motor (Includes Instructions for Optional Wind Deflector)
Aluminum and Steel 5spring Qty. Component Parts Description: LONG BOX: (1) 103 Aluminum Tarp Axle (2) 98 Upper Arms with 90 Degree Elbow (2) Lower Aluminum ( 84 ) (1) Aluminum Cross Tube SMALL HARDWARE
More informationand Original Series Pickup Lift Mounting Instructions Fullsize Ford Trucks- F present T-270 FILLER STRIP
Fullsize Ford Trucks- F-150 2015-present Preparing the Gate 1. Remo the mounting hardware which is banded to the liftgate. 2. Verify mounting bracket kit (Figure 1 and Table 1). 19-1/4" 3/4" 2-9/16" LEFT
More informationOwner s Manual TC-300 & 310 COMBINATION BODIES
Owner s Manual TC-300 & 310 COMBINATION BODIES TruckCraft Corporation Chambersburg, PA 1-800-755-3867 Rev 08/05 Copyright 2005 Craft Corporation Table Of Contents Page # Warranty 3 Warranty Registration
More informationINSTRUCTIONS, (FORD) SUPER DUTY INSTALLATION KIT (C2 PICKUP LIFTGATES)
LIFT CORPORATION Sht. 1 of 22 DSG# M-16-32 Rev. - Date: 12/13/16 INSTRUCTIONS, (FORD) SUPER DUTY INSTALLATION KIT (C2 PICKUP LIFTGATES) FORD SUPER DUTY F-250, F-350 & F-450 PICKUP TRUCKS, 2017 MODEL KIT
More informationPAGE DESCRIPTION REF. NO.
TABLE OF CONTENTS VC 416 / 516 MANUAL PAGE DESCRIPTION REF. NO. 1 READ THIS FIRST... 416723 2 IMPORTANT WARNING... 416272 3 BODY PROP AND WARNING / CAUTION DECALS... 416288 4 DECAL LOCATIONS... 416128
More informationIn This DIY We Will Show You How To Install Recon Backup Lamps (part # To Run On A Separate Switch & In Reverse.
In This DIY We Will Show You How To Install Recon Backup Lamps (part # 264150 To Run On A Separate Switch & In Reverse. Please Note, There Are Many Ways of Installing These Lights, Including Wiring Methods,
More informationand Original Series Pickup Lift Mounting Instructions FILLER STRIP T-330 PART#13203 BOLT-ON GUSSET
Fullsize Dodge Trucks- 1500 2002-present 2500 & 3500 2003-present Preparing the Gate 1. Remo the mounting hardware which is banded to the liftgate. 2. Verify mounting bracket kit (Figure 1 and Table 1).
More informationImportant: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS
TITAN pt. no.: 99 0000 0509 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS I n B e d F u e l T a n k Shown
More informationTruckCraft Corporation Rev. 1/28/2016 I Table of Contents
TruckCraft Corporation Rev. 1/28/2016 I5-05579 TRUCKCRAFT CORPORATION 5751 Molly Pitcher Hwy. S. Chambersburg, Pa. 17202 Tel. 800.375.3867 Phone 717.375.2900 Fax 717.375.2975 www.truckcraft.com "WHERE
More informationLGT-311L Bumper LED Light Kit EZ-Go RXV Installation Instructions
LGT-311L Bumper LED Light Kit EZ-Go RXV Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative connections
More informationConflicts Note: Toyota Tacoma 2015 LED Bed Lights Preparation. Part Number: Accessory Code: BU1000
Toyota Tacoma 2015 LED Bed Lights Preparation Part Number: 00016-34089 Accessory Code: BU1000 Conflicts Note: Kit Contents Item # Quantity Reqd. Description 1 1 Hardware Kit 2 1 Driver s Side LED assembly
More informationACD-PRO Install in 2008 EvoX
Turning in a counter clockwise direction, unscrew ift knob ACD-PRO Install in 2008 EvoX Slide back and remove the floor console panel assembly Pull up to remove the center console tray Disconnect the plug
More informationVehicle Rear Observation System With Integrated Parking Sensors
Vehicle Rear Observation System With Integrated Parking Sensors Model: CAMSBAR Installation/User Manual Features: 2.5" LCD Color Display 2 Ultra Sonic Rear Obstacle Sensors On-screen Display Function Automatically
More informationInstallation Manual. LHS & LLBS Hide-A-Way Tuckunder Style
Installation Manual LHS & LLBS Hide-A-Way Tuckunder Style 10900 Kenwood Road Cincinnati, OH 45242 Ph: 513-891-6210 Toll-Free: 866-539-6261 Fax: 513-891-4901 www.leymanlift.com sales@leymanlift.com LML00136-5/1/15
More informationT-52. r ve Pickup Lift Mounting Instructions Chevy / GMC- Colorado/ Canyon: 2015-present. Preparing the Gate. Installing the Bolt-on Gussets
Chevy / GMC- Colorado/ Canyon: 2015-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting bracket kit (Figure 1 and Table 1). LEFT BRACKET (RIGHT
More informationTT-15 INSTALLATION INSTRUCTIONS SHOWN WITH OPTIONAL 2 PC. ALUMINUM PLATFORM AND LIGHT KIT
TM TOPLIFTER Tailgates By THIEMAN TT-15 INSTALLATION INSTRUCTIONS SHOWN WITH OPTIONAL 2 PC. ALUMINUM PLATFORM AND LIGHT KIT! IMPORTANT! KEEP IN VEHICLE! PLEASE READ AND UNDERSTAND THE CONTENTS OF THIS
More informationOUT FRONT ELECTRIC HYDRAULIC (W/E-47H) FOR STRAIGHT TRIPEDGE PLOWS (PULL AWAY MOUNTINGS)
80052 March 6, 1995 OUT FRONT ELECTRIC HYDRAULIC (W/E-47H) FOR STRAIGHT TRIPEDGE PLOWS (PULL AWAY MOUNTINGS) ITEM STOCK DESCRIPTION QTY. 51 15759 LIFT UNIT (E-47H) 1 52 817000 020 10" CYLINDER 2 53 15370
More informationRugby Manufacturing Direct Mount Unit Manual
Preface INSTALLATION & OPERATION MANUAL INTRODUCTION IMPORTANT!! Read this manual thoroughly prior to installation and operation. This manual outlines the installation and operation of a Direct Mount unit
More informationINSTRUCTION, DODGE TRUCKS INSTALLATION KIT (C2 LIFTGATES)
LIFT CORPORATION Sht. 1 of 23 DSG# M-14-25 Rev. B Date: 05/16/17 INSTRUCTION, DODGE TRUCKS INSTALLATION KIT (C2 LIFTGATES) DODGE 1500 PICKUPS, 2002 TO 2016 DODGE 2500 PICKUPS, 2003 TO 2016 KIT P/N 289492-01
More informationPart Name/Description Part No. PF3000 PF 3000 Pro U-Bracket Short Bracket PF3000 Pro
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part No. PF3000 PF 3000 Pro U-Bracket Short 2000105-2 1 PFadvantage Bracket PF3000 Pro 2000773 1 Cable Kit
More informationJEEP WRANGLER 5 DOOR 48L ADDITIONAL FUEL TANK FTJW003
JEEP WRANGLER 5 DOOR 48L ADDITIONAL FUEL TANK FTJW003 INSTALL TIME: 1.5 Hours IMPORTANT WARNING! IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE.
More informationC40008 & C40009 EXHAUST BRAKES
EXHAUST BRAKES C40008 & C40009 1995 2003 Ford F250 / F350 7.3 L Powerstroke Diesel with manual transmissions 1995 1998 Ford F250 / F350 7.3 L Powerstroke Diesel with automatic transmission* *Requires the
More informationINSTALLATION INSTRUCTIONS
TM WEIGHTLIFTER Tailgates By THIEMAN TWL 125, 16, 20 INSTALLATION INSTRUCTIONS! IMPORTANT! KEEP IN VEHICLE! PLEASE READ AND UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING THE EQUIPMENT. NTEA T
More informationInstallation Instructions Rotation Control Kit
Installation Instructions Rotation Control Kit 45-101, REV. 11/14 1 TABLE OF CONTENTS SECTION 1 PURPOSE... 3 SECTION 2 INSTALLATION... 4 Test Installation...6 Disabling The System...6 Operation...6 2 45-101,
More informationCTC 200 Cab Trailer Communication Power Line Carrier Technology Communications for Trucks and Trailers
WHEEL MONITOR CTC 200 Cab Trailer Communication Power Line Carrier Technology Communications for Trucks and Trailers Installation Manual for the CTC-200 Modules 2004 Wheel Monitor Inc. 1-905-641-0024 Page
More informationINSTRUCTIONS, RAM DUAL REAR WHEEL TRUCKS INSTALLATION KIT (C2 LIFTGATES)
LIFT CORPORATION Sht. 1 of 23 DSG# M-15-25 Rev. B Date: 05/31/2017 INSTRUCTIONS, RAM DUAL REAR WHEEL TRUCKS INSTALLATION KIT (C2 LIFTGATES) RAM 3500 DUAL REAR WHEEL PICKUP TRUCKS, 2013 TO 2015 KIT P/N
More informationPAGE DESCRIPTION REF. NO.
TABLE OF CONTENTS VC 416 / 516 MANUAL PAGE DESCRIPTION REF. NO. 1 READ THIS FIRST... 416723 2 IMPORTANT WARNING... 416272 3 BODY PROP AND WARNING / CAUTION DECALS... 416288 4 DECAL LOCATIONS... 416128
More informationCANOPY WIRING PATCH KIT INSTALLATION INSTRUCTIONS Holden Colorado RG
CANOPY WIRING PATCH KIT INSTALLATION INSTRUCTIONS Holden Colorado RG IMPORTANT! Read instructions carefully before installation. It is strongly recommended that installation is conducted by an authorized
More informationInstallation Instructions
Installation Instructions SD-600 Serial No. X2-100038 and higher SD-1400 Serial No. X3-100019 and higher Madison Heights, Michigan 48071 800-SALTERS www.snowexproducts.com CUSTOMER COPY TrynEx International
More informationYour Legal Fuel Tank Source.
February 23, 2015 IS# 808 Page 1 of 13 THANK YOU FOR PURCHASING A TRANSFER FLOW 40 GALLON TOOLBOX REFUELING SYSTEM. PLEASE READ THE FOLLOWING PROCEDURES CAREFULLY BEFORE STARTING THE INSTALLATION. CAUTION:
More informationInstallation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com Indianapolis, IN
More informationOwner s Manual TC-515 with Reversed Hoist, Sub-Frame, Deck, & Hitch Mount
Proudly built in the USA Owner s Manual TC-55 with Reversed Hoist, Sub-Frame, Deck, & Hitch Mount TruckCraft Corporation Chambersburg, PA -800-755-87 Copyright c 0 www.truckcraft.com TruckCraft Corporation
More informationLR-3510 Install and Operation Manual
RUGBY MANUFACTURING CO. INDUSTRIAL PARK 515 1st St. NE. RUGBY, NORTH DAKOTA 58368 03 6048 Install and Operation Manual LATEST EDITION: 1st (January 4, 2001) FIRST EDITION: January 4, 2001 Page 2 of 9 WARNINGS:
More informationTAILGATE SPREADER INSTALLATION & OWNER S MANUAL TABLE OF CONTENTS
A Division of Northern Star Industries, Inc. P.O. Box 788 Iron Mountain MI 49801-0788 www.bossplow.com SMARTHITCH 1100 TAILGATE SPREADER INSTALLATION & OWNER S MANUAL TABLE OF CONTENTS S & CAUTIONS...
More informationONBOARD AIR SYSTEM FOR ALL VEHICLES APPLICATIONS
ONBOARD SYSTEM FOR ALL VEHICLES APPLICATIONS Thank you and congratulations on the purchase of a Pacbrake onboard air system. Please read the manual prior to starting to ensure you can complete the installation
More informationAddictive Desert Designs
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationRzr Heater System Part #
Rzr Heater System Part # 2878135 NOTE: This heater unit installs below the center of the dash. If you have a radio mount kit (Polaris Part # 2876897) you may need to cut the top front corner off the mount
More informationLethal Performance Dual FPDM Harness Kit Installation
Lethal Performance Dual FPDM Harness Kit Installation The Lethal Performance Dual FPDM Harness Kit is a plug-and-play modification. Depending on whether you are using the Lethal Performance wire upgrade
More informationM REV B SEPTEMBER 2017
M-16-33 REV B SEPTEMBER 2017 To fi nd maintenance & parts information for your TE-25 or TE-30 Liftgate, go to www. maxonlift.com. Click the PRODUCTS, TUK-A-WAY and TE-25/TE-30 buttons. Open the Maintenance
More informationM JULY 2017 GPTLR Liftgate www. maxonlift.com PRODUCTS, TUK-A-WAY GPTLR Maintenance Manual PRODUCT DOCUMENTATION PARTS PORTAL TUK-A-WAY GPTLR
M-16-24 JULY 2017 To find maintenance information for your GPTLR Liftgate, go to www. maxonlift.com. Click the PRODUCTS, TUK-A-WAY & GPTLR buttons. Open the Maintenance Manual in the PRODUCT DOCUMENTATION
More informationINSTALLER S MANUAL FOR THE AHT TAIL LIFT
ALUHEBETECHNIK Gesellschaft mbh Office: Factory: Hauptplatz 23 Bahnstraße 34 A-2474 Gattendorf Tel. (43) 2142 64260 (43) 2142 64360 E-Mail: Fax. (43) 2142 6434 (43) 2142 64366 office@aht-mhw.com INSTALLER
More informationSL15/20-6 AND SL15/20-10 INSTALLATION INSTRUCTIONS
STOWAWAY SideLoader Tailgates By THIEMAN SL15/20-6 AND SL15/20-10 INSTALLATION INSTRUCTIONS! IMPORTANT! KEEP IN VEHICLE! READ AND UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING THE EQUIPMENT.
More informationM SEPTEMBER 2017
M-17-33 SEPTEMBER 2017 To fi nd maintenance & parts information for your TE-15 or TE-20 Liftgate, go to www. maxonlift.com. Click the PRODUCTS, TUK-A-WAY and TE-15/TE-20 buttons. Open the Maintenance Manual
More informationM REV. F AUGUST 2014 INSTALLATION MANUAL
M-06-02 REV. F AUGUST 2014 INSTALLATION MANUAL MAXON Lift Corp. 2014 TABLE OF CONTENTS SUMMARY OF CHANGES: M-06-02, REVISION F... 4 SAFETY INSTRUCTIONS... 5 WARNINGS... 5 MM-1300 LIFTGATE COMPONENTS...
More informationFailure to heed to any of the following warnings could result in severe bodily injury and/or equipment damage.
INSTALLATION OF HYDRAULIC KIT Page of Bulletin MIH9RRFR08B (Rev 0) SAFETY PRECAUTIONS If any installation problems are encountered, please call G&B Specialties, Inc. for technical assistance before continuing
More informationCantilever Series Mounting Instructions Chevy Express (AD) present
Chevy Express (AD)- 2003-present Preparing the Gate 1. Remove the platform, mounting kit, and bridge assemblies, which are banded to the main assembly. Leave the banding that holds the folding cylinder
More informationP Original Series Cargo Van Lift Mounting Instructions Fullsize Ford Van present. Preparing the Gate
Fullsize Ford Van- 1992-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting kit (Figure 1 and Table 1). S-400-40 STRAP VAN MOUNTING EAR BENT BRACKET
More informationINSTALLER S MANUAL FOR THE AHT TAIL LIFT
ALUHEBETECHNIK Gesellschaft mbh Office: Factory: Hauptplatz 23 Bahnstraße 34 A-2474 Gattendorf Tel. (43) 2142 64260 (43) 2142 64360 E-Mail: Fax. (43) 2142 6434 (43) 2142 64366 office@aht-mhw.com INSTALLER
More informationOne piece harness installation instructions (standard wiring) with 2 plugs 2018 & After
One piece harness installation instructions (standard wiring) with 2 plugs 2018 & After (it requires light kit 800084,800085 or 800086) Page 1 Installation instructions Warning: - Top of battery needs
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2012 RIDGELINE Publications No. AII 12006 Issue Date NOV 2011 PARTS LIST Back-up sensor harness 3 Wire ties with small clips (2 Not used)
More informationINSTRUCTIONS, (FORD) SUPER DUTY INSTALLATION KIT (C2 PICKUP LIFTGATES)
LIFT CORPORATION Sht. 1 of 20 DSG# M-14-32 Rev. B Date: 05/31/2017 INSTRUCTIONS, (FORD) SUPER DUTY INSTALLATION KIT (C2 PICKUP LIFTGATES) FORD SUPER DUTY F-250 PICKUP TRUCKS, 1999-2016 FORD SUPER DUTY
More informationC WD 2 WHEEL LOW KIT FOR DODGE RAM 4WD VEHICLES
C18056-4WD 2 WHEEL LOW KIT FOR 1994-2002 DODGE RAM 4WD VEHICLES Pacbrake s 4WD 2 Wheel Low Kit allows the vehicle operator to engage the transfer case into 4WD low range without engaging the front wheel
More informationC FORD F250 / F L POWERSTROKE DIESEL WITH AUTOMATIC TRANSMISSIONS ONLY
EXHAUST BRAKES C40019 1999-2003 FORD F250 / F350 7.3L POWERSTROKE DIESEL WITH AUTOMATIC TRANSMISSIONS ONLY Getting Started Thank you and congratulations on your purchase of a Pacbrake exhaust retarder.
More informationHummer H up A Hummer H3T up A. 3-5 Hours INSTALLATION GUIDE INSTALLATION TIME SKILL LEVEL.
INSTALLATION GUIDE APPLICATION MODEL YR PART # Hummer H3 2006 - up 5116-01A Hummer H3T 2009 - up 5116-01A INSTALLATION TIME 3-5 Hours Professional installation recommended SKILL LEVEL 1 2 3 = Experienced
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2010 RIDGELINE Publications No. AII 42117 Issue Date AUG 2009 PARTS LIST Back-up sensor harness 3 Wire ties with small clip (2 Not used)
More informationTailgates By THIEMAN M16, 20, 25, 30 MLB16, 20, 25, 30 INSTALLATION INSTRUCTIONS
STOWAWAY Tailgates By THIEMAN M16, 20, 25, 30 MLB16, 20, 25, 30 INSTALLATION INSTRUCTIONS M-25 shown! IMPORTANT! KEEP IN VEHICLE! PLEASE READ AND UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING
More informationCTC 400 Cab Trailer Communication Power Line Carrier Technology Communications for Trucks and Trailers
WHEEL MONITOR CTC 400 Cab Trailer Communication Power Line Carrier Technology Communications for Trucks and Trailers Installation Manual for the CTC-400 Cab and Trailer Modules Wheel Monitor Inc. 1-905-641-0024
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Accent light Kit Pathfinder 999F3 XZ000 - Accent Lighting Kit. Item QTY Description Service Part
More informationGuardian GRD502-A Adapter Matrix
Guardian GRD502-A Adapter Matrix Note: Based on vehicle age and transmission code, it may be necessary to use one of the adapters listed below along with the GRD501 or GRD502 part number. Adapter Application
More informationCantilever Series Mounting Instructions Fullsize Sprinter Van (US) WB (AB) present
Fullsize Sprinter Van (US) 3500 144 WB (AB)- 2007-present Preparing the Gate 1. Remove the platform, mounting kit, license plate assembly, and bridge assemblies, which are banded to the main assembly.
More information8436, 8437, 8438, 8439, 8442, 27480, 27780, 28028, & ISOLATION MODULE ELECTRICAL SYSTEM
September 11, 2003 Lit. No. 27808 8436, 8437, 8438, 8439, 8442, 27480, 27780, 28028, & 28400 ISOLATION MODULE ELECTRICAL SYSTEM Installation Instructions Read this document before installing the snowplow.
More informationFORD BRONCO BODY LIFT KIT INSTALLATION INSTRUCTIONS KIT # KIT #843
FORD BRONCO BODY LIFT KIT INSTALLATION INSTRUCTIONS 1992-1996 2 KIT #842 1992-1996 3 KIT #843 This kit should only be installed on a vehicle that is in good working condition. Before you install the kit,
More informationLPE C5 Battery Relocation Kit
LPE C5 Battery Relocation Kit The LPE C5 Corvette battery relocation kit improves vehicle weight distribution by moving weight to the rear of the vehicle. The improved weight distribution increases traction
More informationOne piece harness installation instructions (standard wiring) with 2 plugs
One piece harness installation instructions (standard wiring) with 2 plugs (it requires light kit 800084 or 800086) Page 1 Installation instructions Warning: - Top of battery needs to be protected. If
More informationInstallation Instructions for TLC79DCA Toyota Landcruiser VDJ79 Series 90lt Auxiliary Tank
Installation Instructions for TLC79DCA Toyota Landcruiser VDJ79 Series 90lt Auxiliary Tank 1. Carry out wiring of PG200 switch gauge unit, suggested switch location is in the large rectangle blank on the
More informationLGT-312L E-Z-Go TXT Light Bar Bumper Kit Installation Instructions
LGT-312L E-Z-Go TXT 2014+ Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More informationEASY DUMP RD3100 / RD3106 (Standard)-(60/40 Split)-(60/40 Divider)- (70/30 Split with Bayne) USER S MANUAL
EASY DUMP RD3100 / RD3106 (Standard)-(60/40 Split)-(60/40 Divider)- (70/30 Split with Bayne) USER S MANUAL *** Important *** Read User s Manual Completely Prior to Operating Par-Kan Company Phone: 1-800-291-5487
More informationInstallation Instructions Clamp Opening Control - Switch Operated
Installation Instructions Clamp Opening Control - Switch Operated 45-078, REV. 8/14 1 TABLE OF CONTENTS SECTION 1 PURPOSE... 3 SECTION 2 INSTALLATION... 4 Test Installation...6 Disabling The System...6
More informationINSTALLATION INSTRUCTIONS
ELECTRIC RETRACTABLE HARD TONNEAU COVER INSTALLATION INSTRUCTIONS BedLocker shown on 2002 Dodge Ram Pace Edwards Company 2400 Commercial Blvd. Centralia WA 98531 (800) 338-3697 toll free (360) 736-9991
More informationINSTRUCTIONS, NISSAN TITAN TRUCK INSTALLATION KIT (C2 PICKUP LIFTGATES)
LIFT CORPORATION Sht. 1 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 INSTRUCTIONS, NISSAN TITAN TRUCK INSTALLATION KIT (C2 PICKUP LIFTGATES) NISSAN TITAN PICKUP TRUCKS, 2004-2015 KIT P/N 295040-01 MOUNTING
More informationPhoto below shows the yellow wire on the left and the black on the right.
2000 pound lift installation photos and troubleshooting helps This photo shows a wired lift. Shown in this photo User will install: From the control cable: small blue wire on front solenoid terminal small
More informationrevised. You can make sure you are looking at the most recent KEEPING SERVICE INFORMATION CURRENT
1 part 1: WELCOME to the Kwikee Products Service Training. It is our sincere hope that the information you gain from this training will enhance your confidence in and familiarity with the products we manufacture.
More informationVEHICLE SPECIFIC ELECTRICAL INSTALLATION INSTRUCTIONS
WESTERN PRODUCTS, P.O. BOX 245038, MILWAUKEE, WI 53224-9538 Lit. No. 63723 VEHICLE SPECIFIC ELECTRICAL INSTALLATION INSTRUCTIONS FORD BRONCO F-150 4x4 F-250/350 4x4 and 2WD FORD SUPER DUTY 1980-1991 Model
More informationPAGE DESCRIPTION REF. NO.
TABLE OF CONTENTS VC 416 / 516 MANUAL PAGE DESCRIPTION REF. NO. 1 READ THIS FIRST... 416733 2 IMPORTANT WARNING... 416272 3 BODY PROP AND WARNING / CAUTION DECALS... 416288 4 DECAL LOCATIONS... 416128
More informationTOYOTA PRIUS FOG LIGHT (Halogen or LED)
Part Number: TPR-413 / TPR-813 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 1 Lower Grill 3 1 Switch Assembly 4 1 Fog Light Operation guide 5 1 Harness Bag Hardware Bag Contents Item
More informationAdjustable Light Kits E-Z-Go TXT All Models Installation Instructions
Adjustable Light Kits E-Z-Go TXT All Models 1996-2013 Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More informationADDICTIVE DESERT DESIGNS
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationInstallation Instructions for Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights
Installation Instructions for 2015-2018 Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights This kit is designed to allow use of your factory fog light operation along with an addition auxiliary
More informationAssembly and Modular Table Power System Installation Instructions for Train Tables
Assembly and Modular Table Power System Installation Instructions for Train Tables Table of Contents Topic Attach Stretcher to Legs Attach Base To Table Top Attach Modesty Panel to Assembly Page 2 3 4
More informationInstallation Manual MDL, DS, DT, SB
www.waltco.com Phone: 800.411.5685 parts@waltco.com Fax: 800.411.5684 Installation Manual MDL, DS, DT, SB 1250 lb. - 3000 lb. Capacity Rail Liftgates Last Change Date Page(s) Description 9-2013 14, 15,
More informationSTEALTH. The MOST Versatile and Easiest To Use Towed Vehicle Braking System available! NEED HELP? Call WARNING
0 STEALTH The MOST Versatile and Easiest To Use Towed Vehicle Braking System available! INSTALLATION manual NEED HELP? Call - -00-0- Read all instructions before installing or operating the Stealth. Failure
More informationINSTRUCTIONS. w w w. h d o n l i n e s h o p. d e SPRINGER AUXILIARY LAMP KIT 1WARNING -J03497 REV General.
INSTRUCTIONS -J097 REV. 0-0-00 Kit Number 6986-0A General Auxiliary/fog lamps are not included in this kit. The lamps must be purchased separately. HDI (International) motorcycles should only use approved
More informationJODALE PERRY. Parts List & Mounting Instructions. Jacobsen HR9016 JDP BUILT FOR LIFE
JODALE PERRY Parts List & Mounting Instructions Jacobsen HR9016 JDP BUILT FOR LIFE Jacobsen HR9016 Mounting Instructions Standard Parts 1 - LH Rear Mounting Bracket 1 - RH Rear Mounting Bracket 1 - Front
More informationRemoving the power steering gear. General. Tools. The description only applies to left-hand drive vehicles with a chassis front end width of 1,020 mm.
General General The description only applies to left-hand drive vehicles with a chassis front end width of 1,020 mm. IMPORTANT! On vehicles with front axle air suspension, the frame must be supported on
More informationWALKER MANUFACTURING COMPANY ASSEMBLY INSTRUCTIONS FOR P/N SC8660 OPERATOR CAB (MD/MT)
WLKER MNUFCTURING COMPNY SSEMLY INSTRUCTIONS FOR P/N SC8660 OPERTOR C (MD/MT) NOTE: This kit has been revised to allow installation on units equipped with the Hi-dump. 1. Remove the two 5/16 whiz lock
More informationGN-3A Polaris General SSV Works 3 Speaker Audio Kit
GN-3A Polaris General SSV Works 3 Speaker Audio Kit pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 17 Kick Panel Speakers Installation pg 21 MRB3 and Dash
More informationConflicts. TOYOTA Prius Foglights. Part Number: Accessory Code: LF1. Factory Fog Lights
TOYOTA Prius 2011- Foglights Part Number: 00016-47401 Accessory Code: LF1 Conflicts Factory Fog Lights Item # Quantity Reqd. Description 1 2 Fog Lamps 2 2 Fog Lamp s bezels 3 1 Switch Assembly 4 1 Fog
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Accent light Kit Versa Note 999F3 4Z000 - Accent Lighting Kit. 999Q9 AY000 - Accessory Service Connector
More informationPARTS LIST: Components. ` Bi-Fold Tonneau Cover
` Bi-Fold Tonneau Cover Fits: 2004-2014 TFX3401 - Ford F150 5.5 2004-2014 TFX3402 - Ford F150 6.5 2015 TFX3403 - Ford F150 5.5 2015 TFX3404 - Ford F150 6.5 1999-2007 TFX3405 - Ford F250/F350 6.5 2008-2015
More informationDetroit Speed, Inc. Selecta-Speed Wiper Kit Corvette P/N:
Detroit Speed, Inc. Selecta-Speed Wiper Kit 1968-72 Corvette P/N: 121621 A downpour of rain will no longer hinder your ability to clearly see the road. The Detroit Speed Selecta-Speed Wiper Kit provides
More informationCantilever Series Mounting Instructions Ram Promaster Extended Body (AH) Present
Ram Promaster Extended Body (AH)- 2014-Present Preparing the Gate 1. Remove the platform, mounting kit, and bridge assemblies, which are banded to the main assembly. Leave the banding that holds the folding
More information2017 Current Ford Raptor Bump Stop Kit Installation Instructions
2017 Current Ford Raptor Bump Stop Kit Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend
More information