DISASSEMBLY TRANSAXLE DISASSEMBLY AND ASSEMBLY. Part 1 Of 3

Size: px
Start display at page:

Download "DISASSEMBLY TRANSAXLE DISASSEMBLY AND ASSEMBLY. Part 1 Of 3"

Transcription

1 2004 Mitsubishi Truck Endeavor V6-3.8L SOHC Vehicle > Transmission and Drivetrain > Automatic Transmission/Transaxle > Service and Repair > Overhaul > F4A5A > Disassembly and Assembly DISASSEMBLY TRANSAXLE DISASSEMBLY AND ASSEMBLY Part 1 Of 3 1/37

2 Part 2 Of 3 2/37

3 3/37

4 Part 3 Of 3 [F4A5A] Part 1 Of 4 4/37

5 Part 2 Of 4 5/37

6 Part 3 Of 4 6/37

7 Part 4 Of 4 7/37

8 [W4A5A> 8/37

9 DISASSEMBLY CAUTION: ^ Because the automatic transaxle is manufactured from high-precision parts, care must be taken not to scratch or damage these parts during disassembly and assembly. ^ The working area should be covered with a rubber mat to keep it clean at all times. ^ Do not wear any cloth gloves and do not use any shop towels during disassembly. Use only nylon cloth, paper towels or any other lint-free material. ^ Parts which have been disassembled should all be cleaned. Metal parts can be cleaned with normal detergent, but they should be dried completely using compressed air. ^ Clutch discs, plastic thrust plates and rubber parts should be cleaned with automatic transmission fluid ( ATF ). ^ If the transaxle body has been damaged, disassemble and clean the cooler system. 1. Remove the transfer and O-ring [W4A5A> 2. Use a dial gauge to measure the input shaft end play. 3. Remove the torque converter. 4. Remove each bracket. 5. Remove the dipstick. 6. Remove the eye bolt, gaskets and the oil cooler feed tube. 9/37

10 7. Remove the input shaft speed sensor and output shaft speed sensor. CAUTION: The manual control lever tightening nut must be removed before removing the valve body. If the valve body is removed before the nut, the park/neutral position switch will be damaged. 10/37

11 8. Loosen the manual control lever tightening nut, and then remove the manual control lever, and the park/neutral position switch. 9. Remove the sealing cap and O-ring. 11/37

12 10. Remove the valve body cover. 11. Remove the manual control shaft detent. 12/37

13 12. Disconnect the solenoid valve harness from the valve body by undoing the fluid temperature sensor and all the connectors. CAUTION: ^ Make sure that the manual control lever and the park/neutral position switch are removed. See step 8. ^ Do not remove the bolts (four pieces) shown in the illustration. 13. Remove the valve body mounting bolts (twenty seven pieces). 13/37

14 CAUTION: Do not lose the two steel balls. 14. Remove the valve body, gasket and the two steel balls. 15. Remove the snap ring from the connector and then push the connector into the transaxle case and remove the solenoid valve harness. 14/37

15 16. Remove the strainer and the second brake retainer oil seal. 15/37

16 17. Remove each accumulator piston and spring. 18. Remove the manual control lever shaft roller. 19. Remove the manual control lever shaft and the parking pawl rod. 16/37

17 20. Remove the torque converter housing mounting bolts (18 pieces), and then remove the torque converter housing. 21. Remove the differential bearing outer race and spacer from the torque converter housing. 22. Remove the O-rings (two pieces). 17/37

18 23. Remove the differential. 24. Remove the differential bearing outer race from the transaxle case. 25. Remove the oil filter. 18/37

19 26. Remove the oil pump mounting bolts (six pieces). 27. Install special tool MD in hole "A." 19/37

20 28. Turn special tools MD to remove the oil pump. 29. Remove the oil pump gasket. 30. Remove thrust washer number /37

21 31. Holding the input shaft, remove the underdrive clutch and input shaft. 32. Remove thrust bearing number /37

22 33. Remove the underdrive clutch hub. 34. Remove the rear cover. 35. Remove thrust race number Remove the seal rings (four pieces). 37. Remove the input shaft rear bearing. 22/37

23 38. Remove the O-rings (three pieces). 39. Remove the reverse and overdrive clutch and thrust bearing number /37

24 40. Remove overdrive clutch hub and thrust bearing number Remove thrust bearing number /37

25 42. Remove the planetary reverse sun gear. 43. Remove the snap ring. 25/37

26 44. Remove the second brake piston and the return spring. 45. Remove the pressure plate, brake discs and brake plates. 26/37

27 46. Remove the planetary carrier assembly. 47. Remove the snap ring. 27/37

28 48. Remove the reaction plate and the brake disc. 49. Remove the snap ring. 28/37

29 50. Remove the brake plates (five pieces), brake discs (six pieces) and pressure plate. 51. Remove the wave spring. 29/37

30 52. Remove the parking pawl shaft, and then remove the spacer and spring. 53. Remove the two parking roller support shafts, and then remove the parking roller support. 30/37

31 54. Remove the one-way clutch inner race and low-reverse brake piston as follows: 1. Using special tools MD and MD998924, compress the one-way clutch inner race. NOTE: This illustration shows F4A5A. 2. Remove the snap ring. 3. Remove the special tools. 4. Remove the one-way clutch inner race, O-ring, spring retainer, return spring and low-reverse brake piston. 31/37

32 55. Remove the four transfer drive gear bearing mounting bolts. Then, turn the gear 1/8 turn (45 degree angle) and remove the remaining bolts. 56. Remove the transfer drive gear. 32/37

33 57. Remove the cap by inserting a screw driver into the center of the cap and prying it up. 58. Using a chisel, remove the staked nut from the output shaft. 33/37

34 CAUTION: The jam nut is reverse threaded. 59. Use special tools MB and MB to remove the output shaft jam nut. 60. Remove the bearing retainer mounting bolts. 34/37

35 61. Tap on the rear end of the output shaft to remove the output shaft, taper roller bearing and collar. 62. Remove the outer race and the spacer. 35/37

36 63. Remove the snap ring. 36/37

37 37/37

2000 Jeep Truck Cherokee 4WD L6-4.0L VIN S

2000 Jeep Truck Cherokee 4WD L6-4.0L VIN S 2000 Jeep Truck Cherokee 4WD L6-4.0L VIN S Vehicle» Transmission and Drivetrain» Automatic Transmission/Transaxle» Service and Repair» 30-40LE (AW4) 4 Speed» Overhaul (Transmission)» Disassembly DISASSEMBLY

More information

AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series TRANSMISSION APPLICATION TABLE

AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series TRANSMISSION APPLICATION TABLE Article Text ARTICLE BEGINNING AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series APPLICATION TRANSMISSION APPLICATION TABLE Vehicle Application Transmission Model Colt 3-Speed (1990-94)... F3A21 Colt Vista

More information

2005 Toyota RAV AUTOMATIC TRANSMISSIONS U240E & U241E Overhaul

2005 Toyota RAV AUTOMATIC TRANSMISSIONS U240E & U241E Overhaul 2001-05 AUTOMATIC TRANSMISSIONS U240E & U241E Overhaul APPLICATION CAUTION: Flush oil cooler and oil cooler lines prior to transaxle installation. Oil cooling system contamination may cause premature transaxle

More information

2007 Jeep Truck Liberty 4WD V6 3.7L VIN K

2007 Jeep Truck Liberty 4WD V6 3.7L VIN K 2007 Jeep Truck Liberty 4WD V6 3.7L VIN K Vehicle» Transmission and Drivetrain» Automatic Transmission/Transaxle» Service and Repair» Overhaul» Disassembly DISASSEMBLY NOTE: If the transmission is being

More information

1 of 25 9/12/2013 9:07 PM

1 of 25 9/12/2013 9:07 PM 1 of 25 9/12/2013 9:07 PM 46RE Automatic Transmission DISASSEMBLY 1. Clean exterior of transmission with suitable solvent or pressure washer. 2. Place transmission in vertical position. 3. Measure the

More information

COMPONENT LOCATOR > DISASSEMBLED VIEWS

COMPONENT LOCATOR > DISASSEMBLED VIEWS Page 1 of 26 Service Manual: AUTOMATIC TRANSAXLE - 4T65-E - OVERHAUL COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Case and Associated Parts Disassembled View (1 of 4) 2004 Buick LeSabre 3.8L Eng Limited

More information

Transaxle. 1. Mount the transaxle to Bench Mounted Holding Fixture T57L-500-B.

Transaxle. 1. Mount the transaxle to Bench Mounted Holding Fixture T57L-500-B. «1997 Aspire Table of Contents» «Group 07: TRANSAXLE» «Section 07-01: Transaxle, Automatic» «DISASSEMBLY» Transaxle CAUTION: To prevent dirt from entering the transaxle, it should be disassembled and kept

More information

AUTOMATIC TRANSAXLE AUTOMATIC TRANSAXLE SYSTEM... COMPONENT PARTS...

AUTOMATIC TRANSAXLE AUTOMATIC TRANSAXLE SYSTEM... COMPONENT PARTS... SYSTEM....... COMPONENT PARTS.................... OIL PUMP.............................. DIRECT CLUTCH........................ FORWARD CLUTCH..................... SECOND BRAKE........................ UNDERDRIVE

More information

2007 Jeep Truck Liberty 4WD V6 3.7L VIN K

2007 Jeep Truck Liberty 4WD V6 3.7L VIN K 2007 Jeep Truck Liberty 4WD V6 3.7L VIN K Vehicle» Transmission and Drivetrain» Automatic Transmission/Transaxle» Service and Repair» Overhaul» Assembly ASSEMBLY NOTE: If the transmission assembly is being

More information

Geo Prizm ( LSi) Toyota Celica 1.8L (1994)

Geo Prizm ( LSi) Toyota Celica 1.8L (1994) Page 1 of 140 ARTICLE BEGINNING APPLICATION TRANSMISSION APPLICATIONS Application Geo Prizm (1993-94 LSi) Toyota Celica 1.6L (1993) Celica 1.8L (1994) Celica 2.2L (1993) Corolla 1.8L MR2 Paseo Transaxle

More information

2007 Dodge Nitro R/T

2007 Dodge Nitro R/T ASSEMBLY AUTOMATIC TRANSMISSION - 42RLE NOTE: If the transmission assembly is being reconditioned (clutch/seal replacement) or replaced, it is necessary to perform the TCM QUICK LEARN Procedure using the

More information

SECTION Automatic Transaxle/Transmission 6R80

SECTION Automatic Transaxle/Transmission 6R80 307-01-i Automatic Transaxle/Transmission 6R80 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 6R80 CONTENTS PAGE Transmission... 307-01-2 307-01-2 Automatic Transaxle/Transmission 6R80 307-01-2

More information

GENERAL SPECIFICATIONS

GENERAL SPECIFICATIONS AUTOMATIC TRANSMISSION - DESCRIPTION AT-3 GENERAL SPECIFICATIONS AUTOMATIC TRANSMISSION -COMPONENT PARTS REMOVAL COMPONENT PARTS REMOVAL COMPONENTS AT-13 Oil Cooler Union Throttle Cable O-Ring A/T Fluid

More information

2013 NATEF Task Area A-2 Automatic Transmission7-2013

2013 NATEF Task Area A-2 Automatic Transmission7-2013 2013 NATEF Task Area A-2 Automatic Transmission7-2013 A. General Transmission & Transaxle Diagnosis B. Transmission & Transaxle Maintenance & Adjustment C. In-Vehicle Transmission & Transaxle Repair D.

More information

2012 NATEF Task Area A 2 Automatic Transmission

2012 NATEF Task Area A 2 Automatic Transmission 2012 NATEF Task Area A 2 Automatic Transmission A. General Transmission & Transaxle Diagnosis B. Transmission & Transaxle Maintenance & Adjustment C. In Vehicle Transmission & Transaxle Repair D. Off Vehicle

More information

Assembly. NOTE: Before beginning assembly, perform/inspect the following:

Assembly. NOTE: Before beginning assembly, perform/inspect the following: Page 1 of 31 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's Reference Component Search: OK 1997 Ford Truck F 150 2WD Pickup V6-4.2L VIN 2

More information

REMOVAL TF REMOVE TRANSFER INDICATOR SWITCH (a) Remove the switches and gaskets. HINT: Indicator switch:

REMOVAL TF REMOVE TRANSFER INDICATOR SWITCH (a) Remove the switches and gaskets. HINT: Indicator switch: 20 NO. 1 NO. 2 F043499 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag

More information

ABBREVIATIONS USED IN THIS

ABBREVIATIONS USED IN THIS IN10 INTRODUCTION ABBREVIATIONS USED IN THIS MANUAL ABBREVIATIONS USED IN THIS MANUAL ATF Automatic Transmission Fluid B 0 Overdrive Brake B 2 Second Brake B 3 No. 3 Brake C 0 Overdrive Direct Clutch C

More information

DISASSEMBLY AND ASSEMBLY

DISASSEMBLY AND ASSEMBLY 307-01-1 Automatic Transaxle/Transmission 307-01-1 DISASSEMBLY AND ASSEMBLY Transaxle Special Tool(s) Dial Indicator Gauge With Holding Fixture 100-002 (TOOL-4201-C) Special Tool(s) Test Plate Screw Set,

More information

1. General Description

1. General Description 1. General Description A: SPECIFICATION 1. MANUAL TRANSMISSION AND FRONT DIFFERENTIAL Type Transmission gear ratio Front reduction gear Rear reduction gear Front differential Center differential Final

More information

2001 Chevrolet Corvette AUTOMATIC TRANSMISSIONS Hydra-Matic 4L60-E - Overhaul

2001 Chevrolet Corvette AUTOMATIC TRANSMISSIONS Hydra-Matic 4L60-E - Overhaul 2001-03 AUTOMATIC TRANSMISSIONS Hydra-Matic 4L60-E - Overhaul APPLICATION CAUTION: Flush oil cooler and oil cooler lines prior to transmission installation. Oil cooling system contamination may cause premature

More information

ALLDATA Online Mitsubishi Eclipse GS L4-2350cc 2.4L SOHC MFI - Transaxle Disassembly... Transaxle Disassembly and Reassembly

ALLDATA Online Mitsubishi Eclipse GS L4-2350cc 2.4L SOHC MFI - Transaxle Disassembly... Transaxle Disassembly and Reassembly ALLDATA Online - 2002 Mitsubishi Eclipse GS L4-2350cc 2.4L SOHC MFI - Transaxle Disassembly... Page 1 of 21 Home Account Contact ALLDATA Log Out Help BEST FORD BEST FORD00001 Select Vehicle New TSBs Technician's

More information

ABBREVIATIONS USED IN THIS MANUAL

ABBREVIATIONS USED IN THIS MANUAL IN6 INTRODUCTION Abbreviations Used in This Manual ABBREVIATIONS USED IN THIS MANUAL A/T ATM Automatic Transmission ATF Automatic Transmission Fluid B 0 Overdrive Brake B 1 Second Coast Brake B 2 Second

More information

23. Planetary Gear and Low Clutch S510212

23. Planetary Gear and Low Clutch S510212 Automatic Transmission 23. Planetary Gear and Low Clutch S510212 A: REMOVAL S510212A18 1) Extract the torque converter clutch assembly. 2) Remove

More information

DISASSEMBLY. Transmission. All vehicles

DISASSEMBLY. Transmission. All vehicles 307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 DISASSEMBLY Transmission Special Tool(s) Holding Fixture, Transmission 307-262 (T93T-77002-AH) Special Tool(s) Remover, Servo 307-347 (T97T-7D021-A)

More information

2003 E-Series Workshop Manual

2003 E-Series Workshop Manual Page 1 of 20 SECTION 307-01B: Automatic Transmission 4R70W 2003 E-Series Workshop Manual ASSEMBLY Procedure revision date: 04/27/2006 Transmission Printable View (1828 KB) Special Tool(s) Dial Indicator

More information

ALLDATA Online Mitsubishi Eclipse GS L4-2350cc 2.4L SOHC MFI - Input Shaft. Input Shaft

ALLDATA Online Mitsubishi Eclipse GS L4-2350cc 2.4L SOHC MFI - Input Shaft. Input Shaft Page 1 of 16 Home Account Contact ALLDATA Log Out Help BEST FORD BEST FORD00001 Select Vehicle New TSBs Technician's Reference Component Search: OK 2002 Mitsubishi Eclipse GS L4-2350cc 2.4L SOHC MFI Conversion

More information

NOTE: Clean and inspect all components. Replace any components which show evidence of excessive wear or scoring.

NOTE: Clean and inspect all components. Replace any components which show evidence of excessive wear or scoring. ASSEMBLY (AUTOMATIC 545RFE)... ASSEMBLY NOTE: Apply trans jell or petroleum jelly to all slide portions, rolling contacts surfaces, thrust surfaces etc. to prevent burnout during initial operation. Lubricate

More information

Zoom and Print Options

Zoom and Print Options 1 of 63 8/26/2017, 7:04 AM Vehicle» Transmission and Drivetrain» Transfer Case» Service and Repair» Procedures» Isuzu T150» Overhaul (Unit Repair)» 1. Transfer Case Disassemble Transfer Case Disassemble

More information

Page 1 of 10 Main Components and Functions Torque Converter 1 Cover (Part of 7902) 2 Converter Damper Plate 3 O-Ring (Part of 7902) 4 Turbine Assembly (Part of 7902) 5 Selective Spacer 6 Thrust Washer

More information

AUTOMATIC TRANSAXLE F4A33, W4A32, W4A33 CONTENTS

AUTOMATIC TRANSAXLE F4A33, W4A32, W4A33 CONTENTS AUTOMATIC TRANSAXLE F4A33, W4A32, W4A33 CONTENTS ANNULUS GEAR AND TRANSFER DRIVE GEAR SET... 100 CENTER DIFFERENTIAL - 4WD... 115 DIFFERENTIAL... 102 END CLUTCH... 94 EXTENSION HOUSING - 4WD... 130 FRONT

More information

Page 1 of 22 SECTION 307-01: Automatic Transaxle/Transmission 4R70E/4R75E ASSEMBLY Procedure revision date: 05/29/2009 Transmission Printable View (1554 KB) Special Tool(s) Air Test Plate, Transmission

More information

INDEX BACK AUTOMATIC TRANSMISSION SERVICE GROUP SW 107TH AVENUE MIAMI, FLORIDA (305) Copyright ATSG 2005

INDEX BACK AUTOMATIC TRANSMISSION SERVICE GROUP SW 107TH AVENUE MIAMI, FLORIDA (305) Copyright ATSG 2005 BACK INDEX MITSUBISHI F4A4, F4A42, F4A5 IDENTIFICATION CODE STAMPING LOCATION... GEAR RATIO IDENTIFICATION... INTERNAL COMPONENT AND SOLENOID APPLICATION CHART... FLUID REQUIREMENTS... CASE CONNECTOR TERMINAL

More information

Aisin Warner LE 1998-Up Nissan UD Isuzu RNJ Mitsubishi FUSO

Aisin Warner LE 1998-Up Nissan UD Isuzu RNJ Mitsubishi FUSO Aisin Warner 450-43LE 1998-Up Nissan UD Isuzu RNJ Mitsubishi FUSO AISIN SEIKI CO., LTD. SERIAL NO. 9A0001 Year: 1999 Month: January Ex. B: February C: March D: April * * L: December Serial Numbers Component

More information

REASSEMBLY AT BEARING POSITION (a) Check bearing position. Bearing diameter A750E AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT

REASSEMBLY AT BEARING POSITION (a) Check bearing position. Bearing diameter A750E AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT T 375 RESSEMBLY 1. BERING OSITION (a) Check bearing position. B C E F 028813E02 Bearing diameter Mark Front Race iameter Inside / Outside Thrust Bearing iameter Inside / Outside Rear Race iameter Inside

More information

DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts

DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts DRIVE AXLE 1994 Volvo 960 1994 DRIVE AXLES Volvo Differentials & Axle Shafts 960 DESCRIPTION & OPERATION All 960 station wagon models use type 1041 rear axle assembly. All 960 4-door models use type 1045

More information

DF 47 DIFFERENTIAL REAR DIFFERENTIAL CARRIER ASSEMBLY REMOVAL

DF 47 DIFFERENTIAL REAR DIFFERENTIAL CARRIER ASSEMBLY REMOVAL 47 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE REAR WHEEL 3. DRAIN BRAKE FLUID Immediately wash off any brake fluid that comes into contact with any painted surfaces. 4. DRAIN

More information

NOTE: Clean and inspect all components. Replace any components which show evidence of excessive wear or scoring.

NOTE: Clean and inspect all components. Replace any components which show evidence of excessive wear or scoring. 21 - Transmission and Transfer Case/Automatic - 68RFE/Assembly ASSEMBLY Labor Operations: Click to display a list of Labor Operations associated with this procedure Special Tools: Click to display a list

More information

AUTOMATIC TRANSMISSIONS. General Motors Corp. Hydra-Matic 4L60-E Overhaul

AUTOMATIC TRANSMISSIONS. General Motors Corp. Hydra-Matic 4L60-E Overhaul 1997-98 AUTOMATIC TRANSMISSIONS General Motors Corp. Hydra-Matic 4L60-E Overhaul APPLICATION TRANSMISSION APPLICATIONS Application Corvette Transaxle 4L60-E IDENTIFICATION The 4L60-E transmission can be

More information

Step 3: Remove the six 8mm retaining bolts for the pressure manifold switch assembly. The manifold switch will not be re-installed.

Step 3: Remove the six 8mm retaining bolts for the pressure manifold switch assembly. The manifold switch will not be re-installed. 1 INSTRUCTIONS TCI 274500/274501 4L80E Trans Brake Valve Body Thank you for choosing TCI products. We are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning

More information

03' SORENTO DSL 2.5L EM SS DS BR TRA TRM CH RT ST USE. No. Tool No. Tool Name ILLUSTRATION GRADE A O 1/8

03' SORENTO DSL 2.5L EM SS DS BR TRA TRM CH RT ST USE. No. Tool No. Tool Name ILLUSTRATION GRADE A O 1/8 No. Tool No. Tool Name ILLUSTRATION GRADE 1 09214-4A000 Timing chain lower front cover oil seal installer Removal and installation of intake and exhaust valves 2 09216-21100 Busing remover and insatller

More information

CLUTCH Nissan 240SX DESCRIPTION PEDAL HEIGHT & FREE PLAY ADJUST CLUTCH ASSEMBLY R & I Clutch. Pathfinder, Pickup, 240SX, 300ZX

CLUTCH Nissan 240SX DESCRIPTION PEDAL HEIGHT & FREE PLAY ADJUST CLUTCH ASSEMBLY R & I Clutch. Pathfinder, Pickup, 240SX, 300ZX CLUTCH 1990 Nissan 240SX 1990 Clutch Pathfinder, Pickup, 240SX, 300ZX DESCRIPTION Clutch is of dry, single disc type, with a diaphragm spring type pressure plate. Clutch release bearing is prelubricated.

More information

MANUAL TRANSAXLE SECTIONMT CONTENTS IDX. Shift Control Components...34

MANUAL TRANSAXLE SECTIONMT CONTENTS IDX. Shift Control Components...34 MANUAL TRANSAXLE SECTIONMT GI MA EM LC EC CONTENTS FE PREPARATION...3 Special Service Tools...3 Commercial Service Tools...5 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...6 NVH Troubleshooting

More information

REAR AXLE Click on the applicable bookmark to selected the required model year

REAR AXLE Click on the applicable bookmark to selected the required model year REAR AXLE 27-2 REAR AXLE General Information GENERAL INFORMATION 27100010118 The rear axle is a banjo-type semi-floating type. The axle shaft bearings are: *Single taper bearings for vehicles without

More information

MANUAL TRANS OVERHAUL - BORG-WARNER - T56 6-SPEED MANUAL TRANSMISSIONS Borg-Warner T56 (MM6) 6-Speed

MANUAL TRANS OVERHAUL - BORG-WARNER - T56 6-SPEED MANUAL TRANSMISSIONS Borg-Warner T56 (MM6) 6-Speed IDENTIFICATION MANUAL TRANS OVERHAUL - BORG-WARNER - T56 6-SPEED 1998 MANUAL TRANSMISSIONS Borg-Warner T56 (MM6) 6-Speed Transmission has 2 identification labels, located on lower left side of case. One

More information

AUTOMATIC TRANSMISSIONS ZF 4HP 18

AUTOMATIC TRANSMISSIONS ZF 4HP 18 AUTO TRANS OVERHAUL - ZF 4HP 18 Article Text 1991 Eagle Premier For Dan's Transmission Service 10 Jefferson Place Fort Walton Beach FL 32548 1997 Mitchell Repair Information Company, All Rights Reserved.

More information

AUTOMATIC TRANSMISSION - 42RLE

AUTOMATIC TRANSMISSION - 42RLE TJ AUTOMATIC TRANSMISSION - 42RLE 21-37 AUTOMATIC TRANSMISSION - 42RLE TABLE OF CONTENTS page AUTOMATIC TRANSMISSION - 42RLE DESCRIPTION...38 OPERATION...40 DIAGNOSIS AND TESTING DIAGNOSIS AND TESTING

More information

4T80E. FWD 4 Speed Primary/Secondary Pump. 2-3 Accum. Valve Body Cover Channel Plate Upper Valve Body.

4T80E. FWD 4 Speed Primary/Secondary Pump. 2-3 Accum. Valve Body Cover Channel Plate Upper Valve Body. 4T80E FWD 4 Speed 2 190 A 191 54 55 250 Valve Body Cover 156 Primary/Secondary Pump 155 129 151 152 157 3 Upper Valve Body 2-3 Accum. 183 53 182 Channel Plate 20 21 60 135 91 195 72 73 B 33 2nd Clutch

More information

OVERHAUL. 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance.

OVERHAUL. 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance. 41135 OVERHAUL 4108901 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance. 0.10 0.40 mm (0.0039 0.0157 in.) C68252 2. INSPECT 2ND GEAR THRUST CLEARANCE

More information

SECTION Automatic Transaxle/Transmission 6R80

SECTION Automatic Transaxle/Transmission 6R80 307-01-i Automatic Transaxle/Transmission 6R80 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 6R80 CONTENTS PAGE Forward Clutch Assembly... 307-01-2 307-01-2 Automatic Transaxle/Transmission

More information

DRIVE AXLE Nissan 240SX DESCRIPTION & OPERATION AXLE RATIO & IDENTIFICATION AXLE SHAFT & BEARING R & I DRIVE SHAFT R & I

DRIVE AXLE Nissan 240SX DESCRIPTION & OPERATION AXLE RATIO & IDENTIFICATION AXLE SHAFT & BEARING R & I DRIVE SHAFT R & I DRIVE AXLE 1990 Nissan 240SX 1990 DRIVE AXLES Rear Axle - R200 240SX, 300ZX DESCRIPTION & OPERATION The axle assembly is a hypoid type gear with integral carrier housing. The pinion bearing preload adjustment

More information

LIFT TRUCK SERIES: G35S-2 G40S-2 G45S-2 G40SC-2 G45SC-2 G50SC-2. November 15, 2000 CODE 3150 LT3150-L0 SUBJECT: NEW DRIVE AXLE

LIFT TRUCK SERIES: G35S-2 G40S-2 G45S-2 G40SC-2 G45SC-2 G50SC-2. November 15, 2000 CODE 3150 LT3150-L0 SUBJECT: NEW DRIVE AXLE LIFT TRUCK SERIES: G35S-2 G40S-2 G45S-2 G40SC-2 G45SC-2 G50SC-2 November 15, 2000 CODE 3150 LT3150-L0 SUBJECT: NEW DRIVE AXLE A new drive axle has been introduced in the above model lift trucks. The purpose

More information

Technical Service Bulletin

Technical Service Bulletin Page 1 of 41 MITSUBISHI MOTORS Technical Service Bulletin SUBJECT No: NOISE FROM CVT AT ALL ENGINE SPEEDS DATE: February, 2015 MODEL: See below CIRCULATE TO: I[ ]GENERAL MANAGER I [ X l PARTS MANAGER I

More information

TO INDEX DIFFERENTIAL FRONT DIFFERENTIAL CARRIER OIL SEAL (4WD) FRONT DIFFERENTIAL CARRIER ASSEMBLY (4WD) REAR DIFFERENTIAL CARRIER OIL SEAL

TO INDEX DIFFERENTIAL FRONT DIFFERENTIAL CARRIER OIL SEAL (4WD) FRONT DIFFERENTIAL CARRIER ASSEMBLY (4WD) REAR DIFFERENTIAL CARRIER OIL SEAL TO INDEX DRIVE LINE / AXLE DIFFERENTIAL DIFFERENTIAL SYSTEM PRECAUTIONS.............................................. OPERATION CHECK......................................... PROBLEM SYMPTOMS TABLE.................................

More information

1. General Description

1. General Description 1. General Description A: SPECIFICATIONS 1. Type Transmission gear ratio Front reduction gear Rear reduction gear 2. TRANSMISSION GEAR OIL Recommended oil Final Transfer 5-forward speeds with synchromesh

More information

1994 Mitsubishi Eclipse GS

1994 Mitsubishi Eclipse GS APPLICATIONS CHRYSLER MOTORS MANUAL TRANS OVERHAUL - MITSUBISHI W5M & W6M SERIES MANUAL TRANSMISSIONS Mitsubishi W5M31, TRANSMISSION APPLICATIONS (CHRYSLER MOTORS) Vehicle Application Transmission Model

More information

STEPS Install the (A) input shaft with long spliced end first. Install the (B) aligning pin.

STEPS Install the (A) input shaft with long spliced end first. Install the (B) aligning pin. 1999 Ford Truck Econoline E450 Super Duty V10-6.8L VIN S Vehicle > Transmission and Drivetrain > Automatic Transmission/Transaxle > Service and Repair > Overhaul > 4R100 > Assembly STEPS 51-94 51. Install

More information

Output Shaft Assembly COMPONENTS

Output Shaft Assembly COMPONENTS MT140 Component Parts (Output Shaft Assembly Output Shaft Assembly COMPONENTS DISASSEMBLY OF OUTPUT SHAFT ASSEMBLY 1. REMOVE SLEEVE FROM OUTPUT SHAFT Using SST, remove the sleeve from the output shaft.

More information

ASSEMBLY PROCEDURE AUTOMATIC TRANSMISSION 5A-173. Transmission

ASSEMBLY PROCEDURE AUTOMATIC TRANSMISSION 5A-173. Transmission AUTOMATIC TRANSMISSION 5A-173 ASSEMBLY PROCEDURE Transmission Tools Required 0555-336256 Transmission Bench Cradle 0555-336258 Cross Shaft Pin Remover/Installer (Detent Lever) 0555-336262 Cross Shaft Seal

More information

2002 F-Super Duty /Excursion Workshop Manual

2002 F-Super Duty /Excursion Workshop Manual Page 1 of 25 SECTION 307-01: Automatic Transaxle/Transmission 2002 F-Super Duty 250-550/Excursion Workshop Manual ASSEMBLY Procedure revision date: 05/23/2001 Transmission Special Tool(s) Remover, O-Ring

More information

TERMS FOR AUTOMATIC TRANSAXLE REPAIR MANUAL

TERMS FOR AUTOMATIC TRANSAXLE REPAIR MANUAL 016 INTRODUCTION TERMS FOR AUTOMATIC TRANSAXLE REPAIR MANUAL TERMS FOR AUTOMATIC TRANSAXLE REPAIR MANUAL ABBREVIATIONS USED IN MANUAL 0103C06 Abbreviations ASSY Assembly ATF Automatic Transaxle Fluid B

More information

1990 SUSPENSION Front ES250, LS400

1990 SUSPENSION Front ES250, LS400 SUSPENSION - FRONT Article Text 1990 Lexus LS 400 For Lextreme Copyright 1998 Mitchell Repair Information Company, LLC Thursday, January 29, 2004 04:56PM ARTICLE BEGINNING 1990 SUSPENSION Front ES250,

More information

TRANSMISSION PARTS BOOK

TRANSMISSION PARTS BOOK TRANSMISSION PARTS BOOK SS-6, SS-636, SS-836 SS-8, SS-08 DATE: 7-3-96 CLARK 8000 SERIES INTERMEDIATE DROP BARAGA PRODUCTS, INC. 55 N. Superior Ave. Baraga, MI 9908-08 Ph. (906) 353-6675 Fax (906) 353-75J

More information

TRANSFER CASE Mitsubishi Montero APPLICATION DESCRIPTION TESTING 4WD INDICATOR CONTROL UNIT (MONTERO) DETECTION SWITCH

TRANSFER CASE Mitsubishi Montero APPLICATION DESCRIPTION TESTING 4WD INDICATOR CONTROL UNIT (MONTERO) DETECTION SWITCH TRANSFER CASE 1993 Mitsubishi Montero 1991-94 TRANSFER CASES Mitsubishi Dodge; Ram-50 Mitsubishi; Pickup, Montero APPLICATION TRANSFER CASE APPLICATIONS TABLE Application (1) Transmission Model Dodge 1991-93

More information

Description and Operation

Description and Operation Description and Operation Clean the automatic transmission to prevent dirt entering when it is reassembled. Lay the removed parts out clearly to make it easier to assess damage and reassemble components.

More information

1991 TRANSMISSION SERVICING Automatic Transmission. Mitsubishi: Eclipse, Galant, Mirage, Montero, Pickup, Precis, 3000GT

1991 TRANSMISSION SERVICING Automatic Transmission. Mitsubishi: Eclipse, Galant, Mirage, Montero, Pickup, Precis, 3000GT Article Text ARTICLE BEGINNING 1991 TRANSMISSION SERVICING Automatic Transmission Mitsubishi: Eclipse, Galant, Mirage, Montero, Pickup, Precis, 3000GT IDENTIFICATION MITSUBISHI AUTOMATIC TRANSMISSION APPLICATIONS

More information

MANUAL TRANSMISSION SECTIONMT CONTENTS IDX FS5W71C. ASSEMBLY...24 Gear Components...24

MANUAL TRANSMISSION SECTIONMT CONTENTS IDX FS5W71C. ASSEMBLY...24 Gear Components...24 MANUAL TRANSMISSION SECTIONMT GI MA EM LC EC CONTENTS FE FS5W71C PREPARATION...3 Special Service Tools...3 Commercial Service Tools...5 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...6 NVH Troubleshooting

More information

SECTION B Manual Transaxle/Transmission TR6060

SECTION B Manual Transaxle/Transmission TR6060 308-03B-i Manual Transaxle/Transmission TR6060 308-03B-i SECTION 308-03B Manual Transaxle/Transmission TR6060 CONTENTS PAGE Transmission... 308-03B-2 308-03B-2 Manual Transaxle/Transmission TR6060 308-03B-2

More information

ASSEMBLY PROCEDURE. Transmission

ASSEMBLY PROCEDURE. Transmission 67 ASSEMBLY PROCEDURE Transmission Tools Required 0555-336256 Transmission Bench Cradle 0555-336258 Cross Shaft Pin Remover/Installer (Detent Lever) 0555-336262 Cross Shaft Seal Installer 0555-336263 Cross

More information

REAR DRIVE SHAFT (3S GTE ENGINE)

REAR DRIVE SHAFT (3S GTE ENGINE) SA52 REAR DRIVE SHAFT (3SGTE ENGINE) COMPONENTS SA53 NOTICE: The axle bearing could be damaged if it is subjected to the vehicle weight, such as when moving the vehicle with the drive shaft removed. Therefore,

More information

4T40E(MN4), 4T45E(MN5) - 4 SPEED TURBO HYDRAMATIC

4T40E(MN4), 4T45E(MN5) - 4 SPEED TURBO HYDRAMATIC 98 4T40E Chevrolet Cavalier/Pontiac Sunfire - 2.3L Quad 4 95-Up Oldsmobile Achieva/Cutlass 98-Up Chevrolet Malibu 98-Up Saturn LS - 4 Cyl. - 4T40E(MN4) 00-Up Saturn LS - 6 cyl. - 4T45E(MN5) 00-Up 12 Bolt

More information

OVERHAUL. 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance.

OVERHAUL. 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance. 4168 OVERHAUL 410F701 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance. 0.10 to 0.40 mm (0.0039 to 0.0157 in.) 0.40 mm (0.0157 in.) C80538 2. INSPECT

More information

AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION SYSTEM PRECAUTION AUTOMATIC TRANSMISSION SYSTEM If the vehicle is equipped with a mobile communication system, refer to the precautions in the IN section.

More information

SUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING

SUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically

More information

Subaru EC8 / 4EAT ( )

Subaru EC8 / 4EAT ( ) Subaru EC8 / 4EAT (1987-98) 4 Speed FWD / AWD 9 105 8 A Input Shaft Differential Differential Housing 10 Pinion 60 30 31 B Reverse Drum 82 95 83 High Drum Reverse Clutch 36 37 39 40 C Forward Hub 42 43

More information

(c) Remove the solenoids.

(c) Remove the solenoids. ONVEHICLE REPAIR AT117 4. WHEN REPLACING 3 SOLENOIDS (a) Disconnect the connectors from the solenoids. (b) Remove the solenoid mounting bolts. Torque: 10 N m (100 kgf cm, 7 ft lbf) (c) Remove the solenoids.

More information

26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) Fax: (03) INSTALLATION MANUAL. for

26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) Fax: (03) INSTALLATION MANUAL. for 26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) 5272 2844 Fax: (03) 5272 2633 GEARLESS CENTRE DIFFERENTIAL FULL-TIME 4X4 TRANSFER CASE CONVERSION DEDICATED LOW RANGE INSTALLATION MANUAL for TOYOTA

More information

SR 55 POWER STEERING GEAR. POWER STEERING GEAR REMOVAL AND INSTALLATION Remove and install the parts, as shown.

SR 55 POWER STEERING GEAR. POWER STEERING GEAR REMOVAL AND INSTALLATION Remove and install the parts, as shown. STEERING SR55 GEAR GEAR REMOVAL AND INSTALLATION Remove and install the parts, as shown. SR56 STEERING MAIN POINT OF REMOVAL AND INSTALLATION 1. REMOVE OIL RESERVOIR 2. REMOVE AIR CLEANER ASSEMBLY 3. DISCONNECT

More information

DISASSEMBLY. Transmission. 2. Remove the 4 clutch housing bolts. Separate the clutch housing from the transmission.

DISASSEMBLY. Transmission. 2. Remove the 4 clutch housing bolts. Separate the clutch housing from the transmission. 308-03A-1 DISASSEMBLY Transmission 308-03A-1 Special Tool(s) Puller, Bearing 205-D064 (D84L-1123-A) or equivalent Remover/Installer, Front Wheel Hub 204-069 (T81P-1104-C) 2. Remove the 4 clutch housing

More information

Troubleshooting The Transmission Hydraulic System

Troubleshooting The Transmission Hydraulic System 416B, 426B, 428B, 436B, & 438B BACKHOE LOADERS TRANSMISSION Testing And Adjusting Troubleshooting The Transmission Hydraulic System Make reference to the following warning and pressure tap locations for

More information

FWD(4spd)F4A41/42, F4A51 (5spd)F5A51 - RWD (4spd)R4A/V4A51 (5spd)R5A/V5A51

FWD(4spd)F4A41/42, F4A51 (5spd)F5A51 - RWD (4spd)R4A/V4A51 (5spd)R5A/V5A51 314 HYUNDAI MITSUBISHI CHRYSLER IMPORTS (All Plastic) F4A41, F4A42 23800 Filter - External Spin-On 23801 F4A51/F5A51 23800B (Metal/ Plastic) F4A41/42 23800A F4A41... Mirage, 1.5L... 96-Up F4A42... Mirage,

More information

SUSPENSION - REAR Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING

SUSPENSION - REAR Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING SUSPENSION - REAR 1988 Toyota Celica REAR SUSPENSION Toyota IRS DESCRIPTION The Toyota Independent Rear Suspension (IRS) system utilizes MacPherson struts, which fasten to axle carrier and wheel housing.

More information

Bearing install tool Spacer disassembly tool Spacer disassembly tool. Handle Puller slide hammer Puller

Bearing install tool Spacer disassembly tool Spacer disassembly tool. Handle Puller slide hammer Puller Bearing install tool Spacer disassembly tool Spacer disassembly tool Handle Puller slide hammer Puller 5th gear lock tool E-ring install tool -98- Chapter 6 Propeller Shaft Universal joint This propeller

More information

MANUAL TRANSMISSION SECTIONMT CONTENTS IDX FS5W71C. Case Components...27

MANUAL TRANSMISSION SECTIONMT CONTENTS IDX FS5W71C. Case Components...27 MANUAL TRANSMISSION SECTIONMT GI MA EM LC EC CONTENTS FE FS5W71C PREPARATION...3 Special Service Tools...3 Commercial Service Tools...5 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...6 NVH Troubleshooting

More information

6F50 / 6F55 / 6T70 / 6T75

6F50 / 6F55 / 6T70 / 6T75 6F50 / 6F55 / 6T70 / 6T75 FWD 6 Speed 42 80 81 82 83 43 A 41 Differential 84 85 86 87 B 60 Driven Transfer Pinion 50 70 51 169 51 70 C 117 61 139 140 D 5 100 62 Pump Drive 141 90 142 Drive Transfer 71

More information

4-50 BRAKES AND STEERING CLUTCHES

4-50 BRAKES AND STEERING CLUTCHES 4-50 BRAKES AND STEERING CLUTCHES Disassembly of bevel gear crown WARNING Lift and handle all heavy items with a hoist of appropriate capacity. Make sure that all parts are held by appropriate slings and

More information

1998 Contour/Mystique Workshop Manual

1998 Contour/Mystique Workshop Manual SECTION 30-01: Automatic Transmission/Transaxle 1998 Contour/Mystique Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 09/14/2001 Main Controls Special Tool(s) Aligner, Selector Shaft 30-S290

More information

ON VEHICLE REPAIR AT 27

ON VEHICLE REPAIR AT 27 AUTOMATIC TRANSMISSION (A43D) Onvehicle Repair AT27 ONVEHICLE REPAIR Valve Body REMOVAL OF VALVE BODY 1. CLEAN TRANSMISSION EXTERIOR To prevent contamination, clean the exterior of the transmission. 2.

More information

DF 78. HINT: Face the rough side of the thrust washer marked by # to the differential case. INSPECTION

DF 78. HINT: Face the rough side of the thrust washer marked by # to the differential case. INSPECTION 78 DIFFERENTIAL REAR DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock) Face the rough side of the thrust washer marked by # to the differential case. INSPECTION 1. DIFFERENTIAL SIDE GEAR (w/ LSD Differential)

More information

HIGH PERFORMANCE TRANSMISSION PARTS Instructions. Line Pressure Booster Kit. TCC Control Plunger Valve Kit. Line Pressure Modulator Plunger Valve Kit

HIGH PERFORMANCE TRANSMISSION PARTS Instructions. Line Pressure Booster Kit. TCC Control Plunger Valve Kit. Line Pressure Modulator Plunger Valve Kit Performance Pack Ford 4R100 Part No. HP-4R100-01 Line Pressure Booster Kit Line-to-Lube Pressure Regulator Valve Line Pressure Booster Kit Valve Sleeve O-Rings (2) TCC Control Plunger Valve Kit Front Lube/Drainback

More information

2004 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX

2004 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX 2004 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX TRANSMISSION SECTION CONTROL SYSTEMS CS 4AT This service manual has been prepared to provide SUBARU service personnel with the necessary information and

More information

REPAIR MANUAL 5 HP - 30 ZF GETRIEBE GMBH SAARBRÜCKEN

REPAIR MANUAL 5 HP - 30 ZF GETRIEBE GMBH SAARBRÜCKEN REPAIR MANUAL 5 HP - 30 ZF GETRIEBE GMBH SAARBRÜCKEN Impressum: Verantwortlich für den Inhalt Abteilung MKTD, ZF Getriebe GmbH, Saarbrücken Druck: HAGER PAPPRINT GmbH, Gedruckt in der BRD Published by

More information

a. remove counterbalance valves, travel motors and travel drives

a. remove counterbalance valves, travel motors and travel drives * For further information, contact Caterpillar Service Technology Group. Start By: a. remove counterbalance valves, travel motors and travel drives 1. Remove the counterbalance valve. See, "Disassemble

More information

HIGH PERFORMANCE TRANSMISSION PARTS Instructions. Line Pressure Booster Kit. TCC Control Plunger Valve Kit. Line Pressure Modulator Plunger Valve Kit

HIGH PERFORMANCE TRANSMISSION PARTS Instructions. Line Pressure Booster Kit. TCC Control Plunger Valve Kit. Line Pressure Modulator Plunger Valve Kit Performance Pack Ford 4R100 Part No. HP-4R100-01 Line Pressure Booster Kit Line-to-Lube Pressure Regulator Valve Line Pressure Booster Kit Valve Sleeve O-Rings (2) TCC Control Plunger Valve Kit Front Lube/Drainback

More information

REPAIR INSTRUCTIONS ON-VEHICLE SERVICE TRANSMISSION AUTOMATIC TRANSMISSION 5A-159. Removal and Installation Procedure

REPAIR INSTRUCTIONS ON-VEHICLE SERVICE TRANSMISSION AUTOMATIC TRANSMISSION 5A-159. Removal and Installation Procedure REPAIR INSTRUCTIONS YAD5A080 AUTOMATIC TRANSMISSION 5A-159 ON-VEHICLE SERVICE TRANSMISSION Removal and Installation Procedure 1. Disconnect the negative battery cable. 2. Disconnect the connectors from

More information

1. Spare Parts List 1.1 Preface The spare parts list is only valid for the type and versions of transmission, as shown below. You will find the transm

1. Spare Parts List 1.1 Preface The spare parts list is only valid for the type and versions of transmission, as shown below. You will find the transm S P A R E P A R T S L I S T A N D E X P L O S I O N V I E W P A S C A T A L O G U E R T R E A S P ZF 15 MIV (HBW 150 V) Cod. 310.01.0100 1. Spare Parts List 1.1 Preface The spare parts list is only valid

More information

Part s Catalog. LX500 Lawn Tractor. Model No. 13AP60RP744. Original Instructions (EN) (01/31/06)

Part s Catalog. LX500 Lawn Tractor.   Model No. 13AP60RP744. Original Instructions (EN) (01/31/06) Part s Catalog For Parts Call 0-- or 0-- LX00 Lawn Tractor Model No. AP0RP Original Instructions (EN) -0 (0//0) For Parts Call 0-- or 0-- Model P0RP NUMBER --00 Turf Tire, 0 x 0.0 x -000-00 Rim,.0 x.0-0-0

More information

AUTO MO TIVE CORPORATION TC 142 PD TRANSFER CASE SERV ICE MAN UAL. Fabco Automotive Corporation,

AUTO MO TIVE CORPORATION TC 142 PD TRANSFER CASE SERV ICE MAN UAL. Fabco Automotive Corporation, AUTO MO TIVE CORPORATION TC 142 PD TRANSFER CASE SERV ICE MAN UAL Fabco Automotive Corporation, TABLE OF CONTENTS SECTION TC-142 PD TRANSFER CASE SERVICE MANUAL Introduction Operation Specification LUBRICATION

More information

22-1 GROUP 22 MANUAL TRANSAXLE CONTENTS MANUAL TRANSAXLE... 22A MANUAL TRANSAXLE OVERHAUL... 22B

22-1 GROUP 22 MANUAL TRANSAXLE CONTENTS MANUAL TRANSAXLE... 22A MANUAL TRANSAXLE OVERHAUL... 22B 22-1 GROUP 22 MANUAL TRANSAXLE CONTENTS............................... 22A OVERHAUL..................... 22B 22A-2 GROUP 22A MANUAL TRANSAXLE CONTENTS GENERAL DESCRIPTION......... 22A-3 DIAGNOSIS 22A-6

More information

FRONT AXLE 26-1 CONTENTS GENERAL INFORMATION... 2 HUB AND KNUCKLE ASSEMBLY SERVICE SPECIFICATIONS... 4 DRIVE SHAFT LUBRICANTS...

FRONT AXLE 26-1 CONTENTS GENERAL INFORMATION... 2 HUB AND KNUCKLE ASSEMBLY SERVICE SPECIFICATIONS... 4 DRIVE SHAFT LUBRICANTS... 26-1 FRONT AXLE CONTENTS GENERAL INFORMATION.................. 2 SERVICE SPECIFICATIONS................. 4 LUBRICANTS.............................. 4 SEALANTS AND ADHESIVES.............. 5 SPECIAL TOOLS...........................

More information