When You Want To Go Fast. Instruction Manual Part # 500,501 Jato Sportsman Nitro Funny Car Kit

Size: px
Start display at page:

Download "When You Want To Go Fast. Instruction Manual Part # 500,501 Jato Sportsman Nitro Funny Car Kit"

Transcription

1 When You Want To Go Fast Instruction Manual Part # 500,501 Jato Sportsman Nitro Funny Car Kit If Our Name is On It, Rest Assured It's The Worlds Finest

2 Read The Instruction Page 1 Here are "Tips and Tricks" that will make your installation quick and easy. Check the last page in this instruction manual for your parts description. 1. Make sure all fuel is removed from the fuel tank in your Jato. 2. Remove all four tires. 3. Unbolt and remove the rear battery hatch cover. If you have the battery in there, remove the battery and disconnect it from the wiring harness. Leave the battery cover off. 4. Remove the engine and exhaust system. 5. Open the radio box lid and unplug the steering servo wire from the receiver. 6. Remove the two front screws on the top plate closest to the shock tower. Remove 7. Turn the truck upside down and remove all screws from the bottom side. 8. Remove the chassis plate. 9. Separate the front end from the mid section. Unbolt the steering servo horn from the servo. Unbolt the steering servo and pull it completely out of the mid section. You are going to re-use the steering servo screws. 10. Remove the stock front bumper. Install the new front bumper #4 that is supplied in the kit #4 Remove Old Install New

3 Page Take the new funny car chassis #5 and lay it flat with the ears up. Bolt on the new stand offs #6 to the chassis using the two #12 counter sunk 3 mm x 10 mm screws supplied with kit. One is longer than the other. The longer stand off gets bolted to the receiver/exhaust side of the chassis, the shorter one gets bolted to the clutch side of the chassis. Next place the frontend shim #3 that is supplied with the kit on top of the chassis plate and bolt the frontend back on top of the frontend shim #3. #12 Actual Size #6 #5 #3 3 mm x 10 mm Counter sink head screws 12. Slide the chrome front bumper/fuel cell #2 over the front ears on the chassis and bolt it up using the four #13 3 mm x 10 mm socket cap screws supplied in the kit. #13 Actual Size #2 3 mm x 10 mm Socket head cap screws 13. Unbolt the stock plastic anti-squat block from the transmission. Install the new aluminum anti-squat block #15 that is supplied with the kit. (Warning) If you do not use the anti-squat block supplied with the kit, the tires will hit the body. You must use the RLC Anti-Squat blocks to keep this from happening. #15 Stock Anti-Squat RLC Anti-Squat 14. Bolt the mid section and transmission onto the funny car chassis. Leave the transmission and screws loose. Leave out the last 2 screws on the end of the chassis plate, they will get installed later. NOTE: Leaving the transmission screws loose will help you install the motor easier when it comes time. Leave these two screws loose Leave these 6 screws loose If Our Name Is On It, Rest Assured It'S The Worlds Finest

4 Page Bolt the steering servo into the new aluminum top plate #7 supplied with the kit as shown. Use the orginal screws that you removed from the Jato. #7 16. Take the top plate with the servo already bolted in and place it on the chassis into postion. Use the four 3 mm x 10 mm button head screws #11 supplied in the kit and hand tighten them down just a few threads. Route the steering servo wire back through where the antenna wire comes out of the radio box. Plug the steering wire back into the receiver. Turn the receiver and radio on to make sure the steering servo is working. If it is working you can install the radio box lid and leave the radio and car receiver on. #11 Actual Size 3mm x 10 mm Button head screws 17. Adjust the steering horn onto the steering servo for proper alignment. Once you get the proper alignment and the steering is good, bolt down the four top plate bolts. Make sure your steering servo horn is tight. 18. Install the engine and exhaust system. Hook up all your linkages, fuel and pressure lines. NOTE: If you are using an easy start system You Must Use Traxxas Part # 4979x Ez-start wiring harness because the stock harness is to short. 19. Remove the rear transmission gear cover. Unbolt the old battery box and wheely bar assembly from the transmission rear cover.

5 Page Install the rear trans cover and tie bar onto the new wheely bar #14 supplied with the kit. Use a small drop of red loc-tite on the bolt that goes inside the trans case and bolts to the lower wheely bar. This will insure the bolt does not vibrate out and ruin the gear set. Tie Bar #14 Small drop of red loc tite 21. Bolt the wheely bar to the transmission case. Install the 2 screws left out earlier as this bolts the trans case gear cover to the trans. Install 22. Set your gear mesh and make sure all screws underneath are now tight. 23. Install the body post mount #9 supplied with the kit. Push this through the black body mount on the funny car body. Next, bolt it in with the screw supplied in the kit. NOTE: It is a little hard to push the body post through. #9 24. Install your 12 mm axal spacers #10 onto the rear axels. Install the pin through the axal then push the plastic hex over the axal until it snaps on. You are now ready to install all four tires. Caution: You must use these rear axal hub spacers or similar ones of the same width or wider or the tires will hit the body. #10

6 Page This is how the conversion looks when it is done. The body mount is simple and easy. The body post #9 slides into the slots on top of the wheely bar mount. Once firmly in the slots just lower the front of the body until it snaps into the front bumper / fuel cell. To flip the body up simply go underneath and pull the plastic latch and pull up. 26. You are now ready to run and test your new funny car conversion kit. Please read the basic set up tips as this will save you a lot of time and trouble. Basic Set Up Tips This will give you a good basic set up to get the car down the track. You can also visit our website and check out the tech section on the Jato Sportsman Funny Car Conversion Check back to the tech section from time to time for updates or call our tech Hours: Mon-Fri 9 AM to 6 PM EST. Frontend alignment camber: negitive degrees. Front toe In: 0 1 negitive degrees Front shocks springs: Green Oil: 30W Piston: 1.4 Rear shock springs: Pink Oil: 30W 1.3 Piston Front sway bar: White Rear sway bar: White Slipper: Tighten slipper until the spring is bottom out. Then back off 1 1/2 turns out. Run the car and see if it slips to much or does not slip enough. The perfect adjustment is when you can not hear it shift into second gear. You achieve this by having it tight and hearing it shift into second gear then back off the sliper nut small turns at a time. CAUTION: To loose of a slipper will cause your pads to get brittle and break and or melt your spur gear. Battery Placement: The best is to buy an after market battery that will fit up front in the front bumper / fuel cell. There are plenty out there that fit. If not, use a flat pack and install it in the mid section location. Add 2 oz. of weight to the very front end. The 2 oz. is just a starting point. Depending on how light or heavy the battery pack you put in the mid section will determin how much weight you will add to the front end. This helps the car track straight 80 feet out and beyond.

7 Part # Parts Description Funny Car Body Front Bumper Fuel Cell Body Mount RLC Front End Shim RLC Front Bumper RLC Jato Sportsman Funny Car Chassis RLC One Long And One Short Stand Offs For Top Plate RLC Top Plate Front Drag Tires RLC Body Mount Post Rear 12 mm Plastic Axal Spacers 11. Screws 4 3 mm x 10 mm Button Head Scews 12. Screws 2 3mm x 10 mm Counter Sunk Screws 13. Screws 4 3 mm x 10 mm Socket Head Cap Screws RLC Sportsman Complete Wheely Bar RLC Anti Squat Block To order parts and accessories call: Mon Fri 9 AM to 6 PM Est. Or go to

New Generation Rear Wheel Drive

New Generation Rear Wheel Drive New Generation Rear Wheel Drive ABC HOBBY ORIGINAL RADIO CONTROL CAR Instruction Manual Study the instructions thoroughly before assembly. REAR 2 WHEEL DRIVE REAR MOUNTED MOTOR BELT DRIVE DOUBLE DECK CHASSIS

More information

ASSOCIATED 1:10 SCALE ELECTRIC BUGGY INSTRUCTION MANUAL FOR THE TEAM ASSOCIATED RC10B Associated Electrics, Inc. RS-1

ASSOCIATED 1:10 SCALE ELECTRIC BUGGY INSTRUCTION MANUAL FOR THE TEAM ASSOCIATED RC10B Associated Electrics, Inc. RS-1 ASSOCIATED 1:10 SCALE ELECTRIC BUGGY INSTRUCTION MANUAL FOR THE TEAM ASSOCIATED RC10B4 TT RS-1 2003-2006 Associated Electrics, Inc. FINAL ADJUSTMENTS RADIO ADJUSTMENTS Use the following

More information

along with standard XT2 Instruction Manual and also XT2 18 Supplementary Sheet.

along with standard XT2 Instruction Manual and also XT2 18 Supplementary Sheet. Use this XT2 Dirt Conversion Supplementary Sheet along with standard XT2 Instruction Manual and also XT2 18 Supplementary Sheet. Parts included in Bag 8: 303141 SHIM 3x5x1.0MM (10) 322111 XT2 COMPOSITE

More information

PLEASE READ INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING THIS MODEL. KEEP THIS MANUAL FOR PARTS NUMBERS WHEN ORDERING.

PLEASE READ INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING THIS MODEL. KEEP THIS MANUAL FOR PARTS NUMBERS WHEN ORDERING. INSTRUCTION MANUAL PLEASE READ INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING THIS MODEL. KEEP THIS MANUAL FOR PARTS NUMBERS WHEN ORDERING. REQUIRED FOR OPERATION THINGS NEEDED You will need to buy a few items

More information

Bag 1. Bag 1. Center Pivot. Center Pivot

Bag 1. Bag 1. Center Pivot. Center Pivot 8 00734 01901 5 Center Pivot Bag 1 3374 - Center Pivot Socket 4019 - Alum Pivot ball 3254-2-56 Button Head *Note - Sometimes it is helpful to slightly over-tighten the top clamp screws, then work the ball

More information

Telluride 4X4 (Model ) Parts List

Telluride 4X4 (Model ) Parts List Telluride 4X4 (Model 67044-1) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arranged alphabetically. Prices are shown in US Dollars. Bearings

More information

Rustler 4X4 (Model ) Parts List

Rustler 4X4 (Model ) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arranged alphabetically. Rustler 4X4 (Model 67064-1) Parts List Bearings & Bushings 4607 Ball bearings (5x11x4mm)

More information

INSTALLATION INSTRUCTIONS FOR THE TOMAHAWK ELECTRIC REVERSE

INSTALLATION INSTRUCTIONS FOR THE TOMAHAWK ELECTRIC REVERSE INSTALLATION INSTRUCTIONS FOR THE TOMAHAWK ELECTRIC REVERSE LAST UPDATED: April 2018 Thank you for choosing the Motor Trike Electric Reverse. We ask that you read the directions before you start and follow

More information

RJS2017 SPORTSMAN RACER KIT LESS ELECTRICS

RJS2017 SPORTSMAN RACER KIT LESS ELECTRICS RJS2017 SPORTSMAN RACER KIT LESS ELECTRICS THANKS FOR BUYING THE RJ SPEED 1/10 SPORTSMAN RACER KIT FOR OVAL RACING, DRAG RACING OR JUST FUN STREET BASHING. THE ASSEMBLY WILL NOT BE DIFFICULT IF YOU READ

More information

PRO1 2001, THE ULTIMATE RACING MACHINE

PRO1 2001, THE ULTIMATE RACING MACHINE PRO1 2001, THE ULTIMATE RACING MACHINE Dear Customer Enclosed you will find several data sheets and illustrations for the 2001 PRO1 race car. All this data is based on what our factory engineers and drivers

More information

Installation Instructions Mustang Air Suspension. Part # Mustang Air Suspension System.

Installation Instructions Mustang Air Suspension. Part # Mustang Air Suspension System. Part # 12120298-1979-1989 Mustang Air Suspension System Recommended Tools Front Components: 12122401 Front ShockWave Strut Rear Components: 12125401 RearShockWave 12125899 Rear Lower StrongArms 12126699

More information

2. With the rear door open remove pull-style clip from the passenger side just below the door latch.

2. With the rear door open remove pull-style clip from the passenger side just below the door latch. LoD Offroad FJ Cruiser Rear Bumper with Tire Carrier Installation Instructions 1. Begin with removing factory spare from the rear door. 2. With the rear door open remove pull-style clip from the passenger

More information

Rustler (Model ) Parts List

Rustler (Model ) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arranged alphabetically. Rustler (Model 37054-1) Parts List Bearings & Bushings 4607 Ball bearings (5x11x4mm)

More information

LS Style Track Alt/AC Serpentine Kit Kit # (Standard Mount Electric Throttle Body Kit) Kit # (Narrow Mount Mechanical Throttle Body Kit)

LS Style Track Alt/AC Serpentine Kit Kit # (Standard Mount Electric Throttle Body Kit) Kit # (Narrow Mount Mechanical Throttle Body Kit) 12/08/16 LS Style Track Alt/AC/PS Serpentine Kit Kit # 20060 (Standard Mount Electronic Throttle Body Kit) Kit # 20065 (Narrow Mount Mechanical Throttle Body Kit) LS Style Track Alt/AC Serpentine Kit Kit

More information

Installation Instructions. Installation Instructions. Part # up Mustang up Mustang Front HQ AirStrut.

Installation Instructions. Installation Instructions. Part # up Mustang up Mustang Front HQ AirStrut. Part # 12272401-2015 up Mustang Recommended Tools 2015 up Mustang Front HQ AirStrut Installation Table of contents Page 2... Included components Page 3... Disassembly and Getting Started Page 4... Strut

More information

Installation Procedure GR40 S197 SLA Front Suspension System (Does not include Aluminum Spindle and Hub Instructions)

Installation Procedure GR40 S197 SLA Front Suspension System (Does not include Aluminum Spindle and Hub Instructions) Installation Procedure GR40 S197 SLA Front Suspension System (Does not include Aluminum Spindle and Hub Instructions) Please take the time and read these instructions first! The GR40 S197 system is designed

More information

2103 NITRO RAIL DRAGSTER KIT

2103 NITRO RAIL DRAGSTER KIT 203 NITRO RAIL DRAGSTER KIT THANKS FOR BUYING RJ SPEED S NITRO DRAG KIT. IT IS A LITEWEIGHT CAR MADE FOR STRAIGHT LINE DRAG RACING AND CAN BE BROKEN IF RUN INTO SOLID OBJECTS AT HIGH SPEED. YOU WILL NEED

More information

RJS2001 PRO STOCK KIT LESS ELECTRICS

RJS2001 PRO STOCK KIT LESS ELECTRICS RJS2001 PRO STOCK KIT LESS ELECTRICS THANKS FOR BUYING RJ SPEED S PRO STOCK DRAG KIT. IT IS MADE FOR STRAIGHT LINE DRAG RACING AND CAN BE BROKEN IF RUN INTO SOLID OBJECTS REPEATEDLY AT HIGH SPEED. IT REQUIRES

More information

Bigfoot (Model ) Parts List

Bigfoot (Model ) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arranged alphabetically. Bigfoot (Model 36084-1) Parts List Bearings & Bushings 4607 Ball bearings (5x11x4mm)

More information

X-Maxx (Model ) Parts List

X-Maxx (Model ) Parts List X-Maxx (Model 77076-4) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arranged alphabetically. Prices are shown in US Dollars. Bearings & Bushings

More information

Install steering rack assembly to chassis using x 3/8 stainless flat head socket screws and 2-6.4mm x 1.1mm blue aluminum spacers as shown.

Install steering rack assembly to chassis using x 3/8 stainless flat head socket screws and 2-6.4mm x 1.1mm blue aluminum spacers as shown. Install steering rack assembly to chassis using 2-4-40 x 3/8 stainless flat head socket screws and 2-6.4mm x 1.1mm blue aluminum spacers as Qty 2, 4-40 x 3/8 fhcs Qty 2, 6.4mm x 1.1mm blue aluminum spacer

More information

Stampede (Model ) Parts List

Stampede (Model ) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arranged alphabetically. Stampede (Model 36054-1) Parts List Bearings & Bushings 4607 Ball bearings (5x11x4mm)

More information

Shown with optional GFR-1017R Body Posts. J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN

Shown with optional GFR-1017R Body Posts. J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN Shown with optional GFR-1017R Body Posts J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN 37034 www.hyperdriveracing.com 1 You now own a state of the art 1/10 scale oval race car. The

More information

RJS WB ELECTRIC T/F DRAGSTER KIT LESS ELECTRICS

RJS WB ELECTRIC T/F DRAGSTER KIT LESS ELECTRICS RJS2006 30 WB ELECTRIC T/F DRAGSTER KIT LESS ELECTRICS THANKS FOR BUYING THIS RJ SPEED DRAGSTER KIT. IT IS MADE FOR STRAIGHT LINE DRAG RACING AND MAY BE BROKEN IF RUN INTO SOLID OBJECTS REPEATEDLY AT HIGH

More information

Stampede (Model ) Parts List

Stampede (Model ) Parts List Stampede (Model 36054-1) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arranged alphabetically. Prices are shown in US Dollars. Bearings & Bushings

More information

WARNING: the engine does not come with oil in it. Please fill the oil before starting. The 200cc hardknock requires 9/10 of a quart of oil.

WARNING: the engine does not come with oil in it. Please fill the oil before starting. The 200cc hardknock requires 9/10 of a quart of oil. WARNING: the engine does not come with oil in it. Please fill the oil before starting. The 200cc hardknock requires 9/10 of a quart of oil. Things needed for assembly. -2 tubes of blue loc-tite. I don

More information

Slash VXL (Model ) Parts List

Slash VXL (Model ) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arranged alphabetically. Slash VXL (Model 58076-3) Parts List Bearings & Bushings 4607 Ball bearings (5x11x4mm)

More information

Installation Instructions Mustang Level 2 Coilover. Part # Mustang Level 2 CoilOver System.

Installation Instructions Mustang Level 2 Coilover. Part # Mustang Level 2 CoilOver System. Part # 22020-979-989 Mustang Level 2 CoilOver System Front Components: 2230 Front CoilOver Strut Recommended Tools Rear Components: 2260 Rear Coilover 225899 Rear Lower StrongArms 226699 Rear Upper StrongArms

More information

RJS2021 LTO SPORT OVAL RACER LESS ELECTRICS

RJS2021 LTO SPORT OVAL RACER LESS ELECTRICS RJS2021 LTO SPORT OVAL RACER LESS ELECTRICS THANKS FOR BUYING THE RJ SPEED 1/10 LTO SPORT KIT FOR OVAL RACING. THE ASSEMBLY WILL NOT BE DIFFICULT IF YOU READ THE TEXT, LOOK AT THE PICTURES, AND THE EXPLODED

More information

OWNER'S MANUAL Magnolia Ave., Chino, CA phone: (909) fax: (909)

OWNER'S MANUAL Magnolia Ave., Chino, CA phone: (909) fax: (909) OWNER'S MANUAL Carefully read through all instructions to familiarize yourself with the parts, construction techniques, and tuning tips outlined in this manual. Being able to grasp the overall design of

More information

2015 up Mustang Front HQ CoilOver Strut

2015 up Mustang Front HQ CoilOver Strut Part # 70-05 up Mustang Recommended Tools 05 up Mustang Front HQ CoilOver Strut Installation Table of contents Page... Included components Page... Disassembly and Getting Started Page... Strut Assembly

More information

J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN 37034

J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN 37034 J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN 37034 www.hyperdriveracing.com 1 You now own a state of the art 1/10 scale oval race car. The Hyperdrive Assault has gone through months

More information

Slash (Model 58024) Parts List

Slash (Model 58024) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arranged alphabetically. Slash (Model 58024) Parts List Bearings & Bushings 4607 Ball bearings (5x11x4mm)

More information

=Apply Thread lock adhesive. =Apply CA Glue =Apply Grease NOTE : BAG 01 BAG 01 BAG 01

=Apply Thread lock adhesive. =Apply CA Glue =Apply Grease NOTE : BAG 01 BAG 01 BAG 01 NOTE : =Apply Thread lock adhesive R80059 One Way Cup R8009 One Way R80 Pulley Set- R80004 Alu-Bulkhead-L BAG 0 =Apply Glue =Apply Grease R8000 Upper Arm Bracket Base R8004 One Way Plastic Shims () R80005

More information

=Apply Thread lock adhesive. =Apply CA Glue =Apply Grease NOTE : BAG 01 BAG 01 BAG 01. R Front One Way Cup (2) R Front One Way

=Apply Thread lock adhesive. =Apply CA Glue =Apply Grease NOTE : BAG 01 BAG 01 BAG 01. R Front One Way Cup (2) R Front One Way NOTE : =Apply Thread lock adhesive R80059 One Way Cup () R8009 One Way R80 Pulley Set- R80004 Alu-Bulkhead-L BAG 0 =Apply Glue =Apply Grease R8000 Upper Arm Bracket Base R8004 One Way Plastic Shims ()

More information

STOP---READ THIS FIRST!

STOP---READ THIS FIRST! STOP---READ THIS FIRST! **Read These Entire Instructions Before Starting Anything** 2009-2014 FORD F-150 6.5 LIFT KIT LIFT KIT INSTRUCTIONS (PART# 57000 & #57050) NOTE: * The factory wheels and tires WILL

More information

Highly Styled, Low Cost Serpentine Drive. Chrysler 383, 440 and 426 HEMI

Highly Styled, Low Cost Serpentine Drive. Chrysler 383, 440 and 426 HEMI Highly Styled, Low Cost Serpentine Drive Installation Instructions Chrysler 8, 440 and 426 HEMI Kit #40720 (without Power Steering) Use 71.5" Serpentine Belt Kit #40725 (with Power Steering) Use 81.5"

More information

PARTS LIST. Alternator Bracket A Main Alternator Bracket 1-P763-A... Idler Pulley. Pulleys. 5/16 x 7/8 SHCS (P/S Option)

PARTS LIST. Alternator Bracket A Main Alternator Bracket 1-P763-A... Idler Pulley. Pulleys. 5/16 x 7/8 SHCS (P/S Option) LS Custom Series Serpentine Kit LS Alternator & Air Conditioning Only Serpentine Kit Kit # 20090-08 LS Alternator, Air Conditioning & Power Steering Serpentine Kit Kit # 20095-08 11/10/16 PARTS LIST Alternator

More information

A7741 Truggy Wheel, Yellow

A7741 Truggy Wheel, Yellow STEP H-01 Tire Mounting BAG H 1 2 A7780B XTT Tire, Blue Truggy Foam Insert Only sold with Tires A7741 Truggy Wheel, Yellow STEP H-02 Tire Gluing The Tires need to be glued to the wheels. This can be done

More information

Assembly Manual. 1/10th Formula 1 Car

Assembly Manual. 1/10th Formula 1 Car Assembly Manual 1/10th Formula 1 Car Center Pivot Bag 1 3374 - Center Pivot Socket 40194 - Hard Anodized Alum Pivot ball 3254-2-56 *Note - Sometimes it is helpful to slightly over-tighten the top clamp

More information

Hurst VMATIC3 INSTALLATION

Hurst VMATIC3 INSTALLATION FORM 159 8530 07/12 Hurst VMATIC3 3-Speed & 4-Speed Automatic Shifter Catalog #3838530 2012 by Hurst Performance The Hurst Vmatic3 shifter can be used in vehicles equipped with most popular three speed

More information

Installation Instructions Right Hand Drive Megashifter

Installation Instructions Right Hand Drive Megashifter Installation Instructions Right Hand Drive Megashifter Part Number 80685 1995, 2001, 2006, 2010 by B&M Racing & Performance Products The B&M Right Hand Drive Megashifter is designed specifically for vehicles

More information

SUSPENSION PARTS LOSB2002 F/R Suspension Arms (pr)(lst2)... $10.00 LOSB2102 Steering Bell Cranks, Shafts, & Chassis Braces (LST/2)... $7.00 LOSB2104 Front Spindles & Carriers (LST2)... $7.00 LOSB2106 Rear

More information

PRO THE ULTIMATE RACING MACHINE

PRO THE ULTIMATE RACING MACHINE PRO1 2004 THE ULTIMATE RACING MACHINE Dear Customer Enclosed you will find several data sheets and illustrations for the 2004 PRO1 race car. All this data is based on what our factory engineers and drivers

More information

PREBUIL UILT ASSEMBLY AND OPERATION MANUAL

PREBUIL UILT ASSEMBLY AND OPERATION MANUAL PREBUIL UILT Length: 15.2" [385mm] Width: 13" [330mm] Height: 5.8" [147mm] Weight: 3.3 lb [1500g] Wheelbase: 11.6" [295mm] Technical Support Information For technical assistance, contact: DuraTrax Product

More information

7207 FRONT BULKHEAD, nylon FRONT BULKHEAD ALUMINUM SUPPORT HINGE PIN, inner, with clips, 1.675" pr GT RACING FRONT

7207 FRONT BULKHEAD, nylon FRONT BULKHEAD ALUMINUM SUPPORT HINGE PIN, inner, with clips, 1.675 pr GT RACING FRONT RC10GT & RTR GT MC 9 McCOY GLOW PLUG 1 3.9 2661 CLUTCH NUT CLIPS 6.7 3216 WASHER, #4 12 1.00 3719 NYLON WIRE TIES, 6" heavy duty 12 2.00 3720 NYLON TIES, 8", light duty for receiver 12 2.00 3721 SELF-TAPPING

More information

RHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS

RHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS PARTS INCLUDED: 2 FRONT UPPER A-ARMS 2 FRONT LOWER A-ARMS 2 UNI-BALL JOINTS 2 UNI-BALL JOINT STUDS 2 UNI-BALL JOINT CAPS 2 RETAINING RINGS 1 FRONT SHOCK ASSEM. 2 DELRON STEERING STOPS 2 SHOCK MOUNT SPACERS

More information

INSTALLATION GUIDE Bolt-On Drag-Race Strut Clip Chevy II

INSTALLATION GUIDE Bolt-On Drag-Race Strut Clip Chevy II INSTALLATION GUIDE 7702 Bolt-On Drag-Race Strut Clip 1962-67 Chevy II Description: STRUT CLIP 4130 BOLT ON 62-67 CHEVY II, INCLUDES 4130 ROUND TUBE FRAME CLIP, DOUBLE-ADJUSTABLE STRUTS, ADJUSTABLE-HEIGHT

More information

=Apply Thread lock adhesive. =Apply CA Glue =Apply Grease NOTE : BAG 01 BAG 01 BAG mm. When track High Traction or want to reduce steering

=Apply Thread lock adhesive. =Apply CA Glue =Apply Grease NOTE : BAG 01 BAG 01 BAG mm. When track High Traction or want to reduce steering NOTE : =Apply Thread lock adhesive R80059 One Way Cup () R8009 One Way R80 Pulley Set- R80004 Alu-Bulkhead-L BAG 0 CA GE =Apply CA Glue =Apply Grease R8000 Upper Arm Bracket Base R8004 One Way Plastic

More information

1993 Jeep Grand Cherokee. WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES 1993 WHEEL ALIGNMENT Chrysler Corp. - Specifications & Procedures

1993 Jeep Grand Cherokee. WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES 1993 WHEEL ALIGNMENT Chrysler Corp. - Specifications & Procedures ADJUSTMENTS CAMBER MEASUREMENT Check camber to determine if any components are bent or damaged. Camber angle is NOT adjustable. If angle is not to specification, components causing problem must be replaced.

More information

ABC HOBBY ORIGINAL RADIO CONTROL CAR

ABC HOBBY ORIGINAL RADIO CONTROL CAR ABC HOBBY ORIGINAL RADIO CONTROL CAR Instruction Manual Study the instructions thoroughly before assembly. FRONT WHEEL DRIVE NEW STYLE STRUT SUSPENSION BATHTUB CHASSIS 4 BEVEL GEAR DIFFERENTIAL FULL ADJUSTABLE

More information

OWNER'S MANUAL 2000 & ROAR National Champion

OWNER'S MANUAL 2000 & ROAR National Champion 2000 & 2001 ROAR National Champion OWNER'S MANUAL Carefully read through all instructions to familiarize yourself with the parts, construction techniques, and tuning tips outlined in this manual. Being

More information

FlexJet Carriage Circuit Board (PCB) Replacement

FlexJet Carriage Circuit Board (PCB) Replacement P/N: 111484 R0 14140 NE 200th St. Woodinville, WA. 98072 PH: (425) 398-8282 FX: (425) 398-8383 ioline.com FlexJet Carriage Circuit Board (PCB) Replacement Notices: Warning! Ensure that all AC power cables

More information

RJS2020 SPORT 3.2 1/10 PAN CAR KIT LESS ELECTRICS

RJS2020 SPORT 3.2 1/10 PAN CAR KIT LESS ELECTRICS RJS2020 SPORT 3.2 1/10 PAN CAR KIT LESS ELECTRICS THANKS FOR BUYING THE RJ SPEED 1/10 SPORT 3.2 KIT. THE ASSEMBLY WILL NOT BE DIFFICULT IF YOU READ THE TEXT, LOOK AT THE PICTURES, AND THE EXPLODED VIEW

More information

SOARSEIKI.Co.,Ltd

SOARSEIKI.Co.,Ltd SOARSEIKI.Co.,Ltd info@soarseiki.com 1 2 3 4 BAGS A1 FRONT AND REAR DIFF 5 BAGS A2 CENTER DIFF 5 BAGS B1 FRONT TRANSMISSION STEP B1-1 Apply a thiin layer of lubricant on the gear. GR160003 BE050110040

More information

Slash: TQ 2.4GHz radio (Model 58024) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arrange

Slash: TQ 2.4GHz radio (Model 58024) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arrange Slash: TQ 2.4GHz radio (Model 58024) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arranged alphabetically. Prices are shown in US Dollars. Bearings

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS HIGH FLOW AIRFLOW METER INSTALLATION INSTRUCTIONS PART NUMBER D763-1600A APPLICATION: 2001-06 E46 M3 Parts List: Hose clamp 64Z (7) Plastic Rivets Air Filter Temp Sensor & Harness (2) Button Head Screws

More information

cfr angle kit INSTALLATION INSTRUCTIONS: 2009-present nissan 370z z infiniti g37 v36 Part Numbers: VOO-akns-0400

cfr angle kit INSTALLATION INSTRUCTIONS: 2009-present nissan 370z z infiniti g37 v36 Part Numbers: VOO-akns-0400 cfr angle kit INSTALLATION INSTRUCTIONS: 2009-present nissan 370z z34 2008-2013 infiniti g37 v36 Part Numbers: VOO-akns-0400 We recommend that installation of all Voodoo13 parts be completed by a professional

More information

MODEL NO & UP

MODEL NO & UP FORM NO. 97 50xi GARDEN TRACTOR MODEL NO. 7570 990000 & UP SET UP INSTRUCTIONS Loose Parts Use the chart below to identify parts for assembly. DESCRIPTION QTY. USE Rear Wheel Wheel Bolt R.H. Wheel Spindle

More information

Installation Instructions

Installation Instructions Part # 099-00 Up Mustang Level Shockwave System Front Components: 0 Front ShockWave Strut Recommended Tools Rear Components: 0 Rear ShockWave Miscellaneous Components: 3033000 3 Gallon Compressor System

More information

Retro it Steering Column

Retro it Steering Column Retro it Steering Column INSTALLATION INSTRUCTIONS for 1976-86 CJ5 & CJ7 FOR PART NUMBER S: 1520800010, 1520800020, 1520800051, 1526800010, 1526800020, 1526800051 S I NCE 1986 Instruction # 8000000010

More information

Rustler (Model ) Parts List

Rustler (Model ) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arranged alphabetically. Rustler (Model 37054-1) Parts List Bearings & Bushings 4607 Ball bearings (5x11x4mm)

More information

Slash 4X4 (Model ) Parts List

Slash 4X4 (Model ) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arranged alphabetically. Slash 4X4 (Model 68054-4) Parts List Bearings & Bushings 4607 Ball bearings (5x11x4mm)

More information

Nitro Slash (Model ) Parts List

Nitro Slash (Model ) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arranged alphabetically. Nitro Slash (Model 44056-3) Parts List Air Filters 5262 Air filter and pre-filter

More information

Slash (Model ) Parts List

Slash (Model ) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arranged alphabetically. Slash (Model 58034-2) Parts List Bearings & Bushings 4607 Ball bearings (5x11x4mm)

More information

Slash 4X4 (Model ) Parts List

Slash 4X4 (Model ) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arranged alphabetically. Slash 4X4 (Model 68054-1) Parts List Bearings & Bushings 4607 Ball bearings (5x11x4mm)

More information

1:8 SCALE GAS POWERED OFF-ROAD BUGGY

1:8 SCALE GAS POWERED OFF-ROAD BUGGY Instruction RTR Manual 1:8 SCALE GAS POWERED OFF-ROAD BUGGY PLEASE READ INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING THIS MODEL. KEEP THIS MANUAL FOR PARTS NUMBERS WHEN ORDERING. REQUIRED FOR OPERATION THINGS

More information

Rustler (Model ) Parts List

Rustler (Model ) Parts List Rustler (Model 37054-1) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arranged alphabetically. Prices are shown in US Dollars. Bearings & Bushings

More information

Installation Guide for Rough Country 30 in. Chrome Series LED Light Bar w/ Hood Mounting Brackets

Installation Guide for Rough Country 30 in. Chrome Series LED Light Bar w/ Hood Mounting Brackets Installation Guide for Rough Country 30 in. Chrome Series LED Light Bar w/ Hood Mounting Brackets Installation Time: 1 Hour Tools Required Trim removal tool (plastic or wood to prevent scratches on the

More information

Slash (Model 58024) Parts List

Slash (Model 58024) Parts List Slash (Model 58024) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arranged alphabetically. Prices are shown in US Dollars. Bearings & Bushings

More information

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with M-Technic bumper and without stock oil cooler

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi (N55 engine) with M-Technic bumper and without stock oil cooler OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0925 APPLICATION 2011-12 E92 335i/xi (N55 engine) with M-Technic bumper and without stock oil cooler Congratulations for being selective enough

More information

Installation Instructions

Installation Instructions Part # 12150399-2005 Up Mustang Level 3 Shockwave System Front Components: 12152411 Front ShockWave Strut Recommended Tools Rear Components: 12155411 Rear ShockWave Miscellaneous Components: 30314000 3

More information

Slash 4X4 (Model ) Parts List

Slash 4X4 (Model ) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arranged alphabetically. Slash 4X4 (Model 68086-3) Parts List Bearings & Bushings 4607 Ball bearings (5x11x4mm)

More information

Installation Instructions

Installation Instructions Part # 12150299-2005 Up Mustang Level 2 Shockwave System Front Components: 12152401 Front ShockWave Strut Recommended Tools Rear Components: 12155401 Rear ShockWave Miscellaneous Components: 30334000 3

More information

Remove the rear tire and the (8) 13mm bolts holding the tire carrier to the tailgate. Remove the 3rd brake light wiring harness.

Remove the rear tire and the (8) 13mm bolts holding the tire carrier to the tailgate. Remove the 3rd brake light wiring harness. J108781 2 4 Rear Bumper & Tire Carrier & Optional Flood Lights Jeep Wrangler JK (2007-2017) Tools Required: Basic Hand Tools 35mm Socket Tape Measure Grease Gun Straight Edge Remove the rear tire and the

More information

PLEASE READ INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING THIS MODEL. KEEP THIS MANUAL FOR PARTS NUMBERS WHEN ORDERING.

PLEASE READ INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING THIS MODEL. KEEP THIS MANUAL FOR PARTS NUMBERS WHEN ORDERING. INSTRUCTION MANUAL PLEASE READ INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING THIS MODEL. KEEP THIS MANUAL FOR PARTS NUMBERS WHEN ORDERING. REQUIRED FOR OPERATION THINGS NEEDED You will need to buy a few items

More information

3.0 Tuning Tips. To Shut Off the Engine: Use the included pipe plug or simply bump the flywheel with a wrench or plastic handled tool.

3.0 Tuning Tips. To Shut Off the Engine: Use the included pipe plug or simply bump the flywheel with a wrench or plastic handled tool. TM 8IGHT 3.0 Tuning Tips Before you start making changes on your 8IGHT 3.0 Off-Road Racing buggy, you need to make a few decisions. First of all, tires, and how they are setup, have a tremendous impact

More information

Slash 4X4 ( ) Parts List

Slash 4X4 ( ) Parts List Slash 4X4 (68086-3) Parts List Parts shown in bold are optional accessories. Part categories and individual part listings are arranged alphabetically. Prices are shown in US Dollars. Bearings & Bushings

More information

CAUTION. INSTALLATION INSTRUCTIONS Part Number Hidden Winch Kit with special XD 9000 Short Drum Winch For Ford F-150 Truck

CAUTION. INSTALLATION INSTRUCTIONS Part Number Hidden Winch Kit with special XD 9000 Short Drum Winch For Ford F-150 Truck INSTALLATION INSTRUCTIONS Part Number 69110 Hidden Winch Kit with special XD 9000 Short Drum Winch For Ford F-150 Truck As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message

More information

Note: The transmission mount just happened to be upside down in this picture. (c) 2015 Total Cost Involved Engineering, Inc. All Rights Reserved.

Note: The transmission mount just happened to be upside down in this picture. (c) 2015 Total Cost Involved Engineering, Inc. All Rights Reserved. 1970-1981 Chevy Camaro & Pontiac Firebird Custom IFS Installation Instructions 1-855-693-1259 www.totalcostinvolved.com CHECK ALL PARTS INCLUDED IN THIS KIT TO THE PARTS LIST BEFORE INSTALLATION. IF ANY

More information

Front Suspension Redo

Front Suspension Redo Front Suspension Redo Message: First, thanks to all the previous posters for guidance in my doing the suspension. As thanks, here s the updated document for doing the front suspension. Procedure: While

More information

Installation Instructions Z-Gate Shifter

Installation Instructions Z-Gate Shifter Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic

More information

STOP---READ THIS FIRST!

STOP---READ THIS FIRST! STOP---READ THIS FIRST! **Read These Entire Instructions Before Starting Anything** 2007-2013 GM 1500 TRUCK LIFT KIT INSTRUCTIONS (PART# 50700 & 50720) 5680 W. Barstow, Fresno, CA 93722 PH: (559) 226-8196

More information

Installation Instructions Sport Shifter

Installation Instructions Sport Shifter The B&M Sport Shifter can be used in vehicles equipped with most popular three speed or four speed automatic transmissions. It is equipped with neutral safety and backup light switches, transmission brackets

More information

Assembly Manual. 1/10th World GT car

Assembly Manual. 1/10th World GT car Assembly Manual 1/10th World GT car Center Pivot Bag 1 3374 - Center Pivot Socket 40194 - Hard Anodized Alum Pivot ball 3254-2-56 Button Head *Note - Sometimes it is helpful to slightly over-tighten the

More information

KIT # CSS-C SUSPENSION LIFT KIT

KIT # CSS-C SUSPENSION LIFT KIT 14385 Veterans Way Moreno Valley, CA 92553 Phone: (951) 571-0212 Fax: (951) 571-0215 2001-2010 CHEVROLET SILVERADO 1500 AND 2500 HD 4WD AND 2WD PICK-UP 1999-2010 CHEVY 2500 4WD PICK-UPS 2001-2010 2500

More information

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0904 APPLICATION: 2011-2012 E90 335i/xi (N55 engine) with BMW standard bumper and with stock oil cooler Congratulations for being selective enough

More information

STOP---READ THIS FIRST!

STOP---READ THIS FIRST! STOP---READ THIS FIRST! **Read These Entire Instructions Before Starting Anything** 2007-2010 GM 1500 TRUCK LIFT KIT INSTRUCTIONS (PART# 50700 & 50720) 5680 W. Barstow, Fresno, CA 93722 PH: (559) 226-8196

More information

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP Please thoroughly review the instructions before and during installation. Keep in mind that this product was designed to be installed by trained dealer

More information

XRAY KITS M18 M18T M18MT PARTS NT18 NT18T NT18MT PARTS. o = option part x = standard included / fits

XRAY KITS M18 M18T M18MT PARTS NT18 NT18T NT18MT PARTS. o = option part x = standard included / fits PRO LiPo PRO USE THE DROP MENU TO FILTER THE SELECTION XRAY KITS o = option part x = standard included / fits 38 0000 XRAY - 4WD SHAFT DRIVE 1/18 MICRO CAR 38 0003 XRAY PRO LiPo - 4WD SHAFT DRIVE 1/18

More information

2101 NITRO PRO STOCK DRAG KIT 2104 NITRO PRO MOD DRAG KIT

2101 NITRO PRO STOCK DRAG KIT 2104 NITRO PRO MOD DRAG KIT 2101 NITRO PRO STOCK DRAG KIT 2104 NITRO PRO MOD DRAG KIT THANKS FOR BUYING RJ SPEED S NITRO DRAG KIT. IT IS A LITEWEIGHT CAR MADE FOR STRAIGHT LINE DRAG RACING AND CAN BE BROKEN IF RUN INTO SOLID OBJECTS

More information

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP Please thoroughly review the instructions before and during installation. Keep in mind that this product was designed to be installed by trained dealer

More information

INSTRUCTION S G-Comp Front Suspension: Chevy Camaro Speedway Motors, Inc Kit Contents:

INSTRUCTION S G-Comp Front Suspension: Chevy Camaro Speedway Motors, Inc Kit Contents: INSTRUCTION S 350-500 G-Comp Front Suspension: 70-81 Chevy Camaro Speedway Motors, Inc. 2017 Kit Contents: 350500.1 G-Comp Subframe, Camaro 350500.2 G-Comp Sway Bar Kit, Camaro 350500.3 Hardware Kit, G-Comp

More information

DODGE RAM 2500

DODGE RAM 2500 81234007 2014-2015 DODGE RAM 2500 Congratulations - your new LevelTow Helper Springs are quality products capable of improving the handling and comfort of your vehicle. As with all products, proper installation

More information

2014 GM 1500 TRUCK STOP---READ THIS FIRST! 7" Lift KIT. **Read These Entire Instructions Before Starting Anything**

2014 GM 1500 TRUCK STOP---READ THIS FIRST! 7 Lift KIT. **Read These Entire Instructions Before Starting Anything** STOP---READ THIS FIRST! **Read These Entire Instructions Before Starting Anything** 2014 GM 1500 TRUCK LIFT KIT INSTRUCTIONS (PART #50768 & #50769 ) 5680 W. Barstow, Fresno, CA 93722 PH: (559) 226-8196

More information

Installation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683

Installation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 Installation Instructions QuickSilver Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 WORK SAFELY! For maximum safety, perform this installation

More information

Installation Instructions Jeep CJ-7

Installation Instructions Jeep CJ-7 Retrofit Steering Column Installation Instructions 1976-86 Jeep CJ-7 For Part # s 1520800010, 152800020, 1520800051 www.ididitinc.com 610 S. Maumee St., Tecumseh, MI 49286 (517) 424-0577 (517) 424-7293

More information

Installation Instructions Megashifter

Installation Instructions Megashifter Installation Instructions Megashifter The B&M Megashifter shifter can be used in vehicles equipped with most popular three speed or four speed automatic transmissions. Your B&M Megashifter comes equipped

More information

DIFFERENTIAL STEERING RACK

DIFFERENTIAL STEERING RACK BAG-A DIFFERENTIAL (2 Sets) +Driver Cap Screw Diff Ball Nylon Nut Thrust Washer Thrust Ball Diff Joint Cup A Allen Wrench 850 Bearing Diff Ring Diff Spring Nylon Nut 850 Bearing Diff Ring Diff Ball Ball

More information

INSTRUCTION S G-Comp Front Suspension: Chevy Nova Speedway Motors, Inc. 2017

INSTRUCTION S G-Comp Front Suspension: Chevy Nova Speedway Motors, Inc. 2017 INSTRUCTION S 350-100 G-Comp Front Suspension: 62-67 Chevy Nova Speedway Motors, Inc. 2017 Kit Contents: 91035700 G-Comp Bare Subframe 350101 G-Comp Support Tubes 91035702 G-Comp Front Subframe Hardware

More information