JARVIS. BRE -1 and BRE -2 BUNG RING EXPANDER EQUIPMENT... TABLE OF

Size: px
Start display at page:

Download "JARVIS. BRE -1 and BRE -2 BUNG RING EXPANDER EQUIPMENT... TABLE OF"

Transcription

1 BRE -1 and BRE -2 BUNG RING EXPANDER EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page BRE BRE Air Hose, 16 feet long Balancer Notice to Employer and Safety Director... 2 Notice to Operators, Maintenance and Cleanup Personnel... 3 Parts Diagram and List... 4 Specifications... 5 Installation Instructions... 5 Operation Instructions... 5 Maintenance Instructions... 6

2 noticetoemployer and safety director page 2 of 8 Keep hands clear NOTICE TO EMPLOYER AND SAFETY DIRECTOR AVOID INJURY 1. Remove and repair any tool that malfunctions. All personnel must be instructed to remove any malfunctioning equipment. 2. Ensure that all employees who use this tool are trained in the proper use of this tool and are aware of the dangers that may arise if they do not follow procedures outlined in this brochure. 3. Enclosed are four (4) copies of NOTICE TO OPERATORS, MAINTENANCE AND CLEANUP PER- SONNEL. Post one copy on the employees bulletin board; give one copy to the operator(s); give one copy to the maintenance foreman; and give one copy to the sub -contract cleanup / internal cleanup foreman. Additional copies will be provided upon request. 4. The tool is designed and intended to be powerful. This fact should be obvious to your employees, but you must emphasize it to them. 5. Ensure that employees wear eye protection in accordance with OSHA s eye and face requirements (29 CFR ) at all times. 6. Never make modifications or alterations to the tool. Replace any missing or illegible labels. 7. Ensure that proper procedures are established (in accordance with OSHA s lockout/tagout procedures 29 CFR ) to prevent accidental startup or release of stored energy. 8. Follow our installation and maintenance instructions for proper installation and care of the tool. 9. Avoid injury. Do not permit the tool to be misused. 10. If you resell or distribute a Jarvis product, you must provide the purchaser with the appropriate safety sheets and tool brochure. Additional copies of safety sheets and tool brochures will be provided upon request.

3 notice to operators, maintenance and cleanup personnel page 3 of 8 Keep hands clear NOTICE TO OPERATORS, MAINTENANCE AND CLEANUP PERSONNEL REMOVE ANY MALFUNCTIONING TOOL FROM SERVICE REPORT ANY PROBLEMS TO YOUR SUPERVISOR 1. Disconnect the air hose in accordance with OSHA s lockout/tagout procedures (29 CFR ) before performing any repair or maintenance. 2. Disconnect the air hose - or have the air hose disconnected - in accordance with OSHA s lockout/tagout procedures (29 CFR ) before performing any cleanup. 3. Disconnect the air hose when the tool is not being used. 4. Never put fingers, hands or other parts of the body in the path of the moving arms when tool is activated. 5. Test the tool prior to use or daily. Depress the lever and the arms should open. Releasethe lever and the arms should close. If the tool malfunctions, remove it from service and report or repair it immediately. 6. Never depress the lever unless you want to use the tool. 7. Never make modifications or alterations to the tool. Replace any missing or illegible labels. 8. Always wear eye protection in accordance with OSHA s eye and face requirements (29 CFR ).

4 parts diagram and list page 4 of 8 Figure A Bung Ring Expander Assembly ** * Before serial number ** BRE--1 only ITEM PART NO. PART NAME QTY Cylinder Housing, BRE * Cylinder Housing, BRE Cylinder Housing, BRE Flat Head Screw Compression Spring U--cup Seal Piston Guide Ring Flat Head Screw Piston Piston Shaft Compression Spring Compression Spring Cylinder Cap Hex Nut Bracket, BRE Bracket, BRE Hex Nut Wheel, BRE Wheel, BRE Minor Arm (left) Minor Arm (right) Bushing 2 ITEM PART NO. PART NAME QTY Pivot Screw ** Rivet Major Arm (left) BRE Major Arm (left) BRE Rivet Roller Roll Pin Major Arm (right) BRE Major Arm (right) BRE Hanger Pivot Screw Lever Dowel Pin Flat Washer Pinch Warning Label Latch Threaded Pin Threaded Plug * Threaded Plug Valve * Valve Quick Connect Plug 1

5 specifications, installation and operation instructions page 5 of 8 SPECIFICATIONS Model BRE -1 and BRE -2 Operating Pressure psi bar Air Consumption Per Cycle at 100 psi ft 3 Per Cycle at 6.9 bar 0.74 L Overall Length 14 in 356 mm Overall Width 5.2 in 132 mm Opening Dimension BRE x 3.9 in 98 x 100 mm BRE x 4.5 in 102 x 114 mm Weight 3.5 lbs 1.6 kg INSTALLATION INSTRUCTIONS 1 Install the BRE -1 or BRE -2 above the work station from a balancer. Jarvis part number is available. 1.1 The BRE -1 or BRE -2 should have sufficient travel to allow the operator to reach the entire work area. 2 Make the necessary air connection. 2.1 The minimum required compressed air supply is ft 3 / cycle at 100 psi (0.74 L / cycle at 6.0 bar). 2.2 An air filter / regulator / lubricator must be installed in the air supply line. Jarvis part number is available. Keep the lubricator filled at all times. OPERATION INSTRUCTIONS IMPORTANT: ALWAYS DISCONNECT THE AIR HOSE IN AC- CORDANCE WITH OSHA S LOCKOUT/TAGOUT PROCE- DURES (29 CFR ) BEFORE PERFORMING ANY MAINTENANCE OR REPAIRS. Refer to Figure A on page 4 for referenced items. 1 Connect air hose. 2 Each day, before you begin operation, go through the following checklist: 2.1 Make sure that the compressed air supply is at the proper pressure and that the lubricator is up to the full mark. (Use Jarvis Air Mist Lubricator Oil; if using a conventional air mist lubricator: set the feed rate at 8-10 drops per minute; if using a micro fog air mist lubricator*: set the feed rate at 100 drops per minute). *Almost all air mist lubricators are micro fog air mist lubricators. 2.2 Make sure the trigger lever is working correctly. Depress the lever (item 28) and the arms should open. Release the lever and the arms should close. If the tool malfunctions, remove it from service and report the problem to your supervisor immediately Depressing the lever (item 28) fully should should engage the latch (item 32) and lock the arms in the open position. Release the arms by sliding the latch (item 32) forward, toward the arms, and the lever (item 28) should disengage, allowing the arms to close. 2.3 Make sure that the BRE -1 or BRE -2 moves freely on the balancer. 3 Making the Seal: 3.1 Slide ring seal onto minor and major arms (items 16, 17, 21 and 25) so that the seal sets into the groove of each arm. Note: The model BRE -1 or BRE -2 must be deactivated with the minor and major arms in the close position when sliding on ring seals. Refer to Figure 1 on page 6 as a guide. 3.2 Depress lever (item 28) to open the ring For easier operation, depress lever (item 28) fully to engage the latch (item 32) and lock the minor and major arms in the open position. 3.3 Place expanded ring seal over colon/intestine at desired location.

6 3.4 Release the latch (if in locked position) and lever, and remove the BRE -1 or BRE -2. Figure 1 Bung Ring Seal Installation Bung Ring Seal maintenance instructions page 6 of 8 in the open position. Release the arms by sliding the latch (item 32) forward, toward the arms, and the lever (item 28) should disengage, allowing the arms to close. 1.2 Inspect all screws, nuts and fasteners and tighten or replace as necessary. Grooves Grooves 1.3 Inspect air hose and fittings for leaks and tighten or replace as necessary. Minor Arm 1.4 Check latch (item 32) for proper locking and unlocking of lever (item 28). Minor Arm Major Arms Minor Arms and Major Arms must be in closed position MAINTENANCE INSTRUCTIONS IMPORTANT: ALWAYS DISCONNECT THE AIR HOSE IN AC- CORDANCE WITH OSHA S LOCKOUT/TAGOUT PROCE- DURES (29 CFR ) BEFORE PERFORMING ANY MAINTENANCE OR REPAIRS. Refer to Figure A on page 4 for referenced items. 1 DAILY: Each day, before you begin operation, go through the following checklist: 1.1 Make sure the control trigger is working correctly. Depress the lever and the arms should open. Release the lever and the arms should close. If the tool malfunctions, repair or remove it from service immediately. Note: Connect the air hose to perform this operation only Depressing the lever (item 28) fully should engage the latch (item 32) and lock the arms 2 AS NECESSARY: 2.1 Disassemble, clean, inspect and lubricate the BRE -1 or BRE -2. Refer to sections 3 through 9 as a procedural guide Lubricate the minor and major arms with Jarvis 1315 White Grease as needed for smooth actuation and to extend the life of the tool. Refer to section 9 as a procedural guide. 3 MINOR ARM AND WHEEL REMOVAL: 3.1 Use a pin pinch to remove roll pins (item 24) and rollers (item 23). 3.2 Remove hex nuts (item 12) and the two pivot screws (item 19) that connect the minor arms (items 16 and 17) to the bracket (item 13). 3.3 Remove minor arms (items 16 and 17). 3.4 Remove hex nuts (item 12) and the two pivot screws (item 19) that connect the wheels (items 15) and bushings (item 18) to the bracket (item 13).

7 maintenance instructions page 7 of Remove wheels (item 15) and bushings (item 18). 3.6 Clean and inspect all parts for wear and replace them if necessary. 4 MINOR ARM AND WHEEL ASSEMBLY: 4.1 Reverse steps and procedures outlined in section 3. See note below Lubricate the minor and major arms (items 16,17, 21 and 25), pivot screws (item 19) and bracket (item 13). Refer to section 9 as a procedural guide. 5 PISTON ASSEMBLY AND SPRING REMOVAL: Caution: The cylinder housing assembly is spring loaded. Use care when removing and installing the cylinder cap and compression springs. 5.1 Remove minor arms (items 16 and 17). Refer to section 3, steps as a procedural guide. 5.2 Rotate major arms (items 21 and 25) outward and away from bracket (item 13). Remove major arms only if lubrication of pivot holes is needed. 5.3 Unscrew cylinder cap (item 11) and remove piston assembly (items 4 through 8) and compression springs (items 9 and 10) from cylinder housing (item 1) as one unit. Note: Bracket (item 13) and hex nut (item 14) are still connected to piston shaft (item 8). 5.4 Unscrew hex nut (item 14) and flat head socket screw (item 6) simultaneously to disassemble piston assembly. The piston assembly contains two compression springs. Use care when removing hex nut and flat head socket screw. 5.5 Remove bracket (item 13). 5.6 Remove cylinder cap (item 11). 5.7 Remove compression springs (items 9 and 10). 5.8 Remove Piston (item 7). 5.9 Remove U -cup seal (item 4) and piston ring guide (item 5) Clean and inspect all parts for wear and replace them if necessary. 6 PISTON ASSEMBLY AND SPRING INSTALLA- TION: Caution: The cylinder housing assembly is spring loaded. Use extreme care when removing and installing the cylinder cap and compression springs. 6.1 Reverse steps and procedures outlined in section 5. See notes below Add two drops of an adhesive compound to each end of piston guide ring (item 5) to keep it firmly in place around the piston (item 7) when installing piston assembly into cylinder housing (item 1) Make sure flat surface of U -cup seal (item 4) is facing toward piston (item 7) when installing Lubricate the minor and major arms (items 16, 17, 21 and 25). Refer to section 9 as a procedural guide. 7 CYLINDER HOUSING DISASSEMBLY: 7.1 Remove dowel pin (item 29) and lever (item 28). 7.2 Unscrew threaded plug (item 34) and pull out valve (item 35) by it s stem. 7.3 Remove flat head screws (item 2) and hanger (item 26), if necessary. 7.4 Remove threaded pin (item 33), latch (item 32) and compression spring (item 3), if necessary. 7.5 Clean and inspect all parts for wear and replace them if necessary. 8 CYLINDER HOUSING ASSEMBLY: 8.1 Reverse steps and procedures outlined in section 7.

8 9 MINOR AND MAJOR ARMS LUBRICATION: 9.1 Apply Jarvis 1315 White Grease to pivot area of pivot screws (items 19 and 27). 9.2 Apply Jarvis 1315 White Grease to slotted holes in bracket (item 13). Refer to Figure 2 as a guide. Slotted Holes maintenance instructions page 8 of 8 Figure 2 Bracket Lubrication Bracket Slotted Holes Apply Jarvis 1315 White Grease to minor arms (items 16 and 17) and major arms (items 21 and 25) where sliding surfaces mate against each other. See notes below. Refer to Figures 3 and 4 as a guide. Figure 3 Minor Arm Lubrication Right Minor Arm Hole Apply a light coat of Jarvis 1315 White Grease to head surface of rivets (items 20 and 22) located on the minor and major arms (items 16, 17, 21 and 25). Left Minor Arm Inside Sliding Surfaces Hole Rivet Apply a generous amount Jarvis 1315 White Grease inside the pivot holes located on the minor and major arms (items 16, 17, 21 and 25) Apply a light coat of Jarvis 1315 White Grease on the inside sliding surfaces of the minor arms (items 16 and 17). Rivet Figure 4 Major Arm Lubrication Channel Area Outside Sliding Surface Right Major Arm Apply a light coat of Jarvis 1315 White Grease on the outside sliding surfaces of the major arms (items 21 and 25). Channel Area Left Major Arm Holes Apply a light coat of Jarvis 1315 White Grease inside the channel area of the major arms (items 21 and 25). Outside Sliding Surface

JARVIS PFI -1 PICKING FINGER INSTALLER

JARVIS PFI -1 PICKING FINGER INSTALLER PFI -1 PICKING FINGER INSTALLER EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page PFI--1... 4311002 Balancer... 1350147 Safety Messages to Employer and Safety Director... 2 Safety Messages

More information

JARVIS. Model TBC. Tongue Bone Cutter

JARVIS. Model TBC. Tongue Bone Cutter Tongue Bone Cutter EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page (Includes Air Control Circuit)... 4019006 (Without Air Control Circuit)... 4019018 Speed Up Kit... 3022064 Balancer... 4042044

More information

JARVIS. Model TWC -1 Tail, TWC -2 and TWC -4 Hog Toe Web Cutters. TWC--1 TWC--2 and TWC--4 EQUIPMENT... TABLE OF

JARVIS. Model TWC -1 Tail, TWC -2 and TWC -4 Hog Toe Web Cutters. TWC--1 TWC--2 and TWC--4 EQUIPMENT... TABLE OF Model TWC -1 Tail, TWC -2 and TWC -4 Hog Toe Web Cutters TWC--1 TWC--2 and TWC--4 Patent Nos. 6,461,232 B1 6,648,746 EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page Model TWC--1 with Control

More information

JARVIS. Model JC II Air Powered Dehider

JARVIS. Model JC II Air Powered Dehider ] Air Powered Dehider U.S. PATENT NO. 5,122,092 EUROPEAN PATENT NO. 0438982 EQUIPMENT SELECTION............. Ordering No. TABLE OF CONTENTS......................... Page JC II Complete Blade Set Blade

More information

JARVIS. Model HTC -80 Hog Toe Cutter

JARVIS. Model HTC -80 Hog Toe Cutter Model HTC -80 Hog Toe Cutter HTC -80 Standard HTC -80 Pistol Grip EQUIPMENT SELECTION... Ordering No. HTC--80 Standard... 4025061 HTC--80 Pistol Grip... 4025100 HTC--80 Pistol Grip Long... 4025114 without

More information

JARVIS. Model 30CL-1 AND 30CL-3 Hock Cutter and Dehorner. 30CL-1 Hock Cutter

JARVIS. Model 30CL-1 AND 30CL-3 Hock Cutter and Dehorner. 30CL-1 Hock Cutter Model 30CL-1 AND 30CL-3 Hock Cutter and Dehorner 30CL-1 Hock Cutter with Leg Grabber 30CL-1 Hock Cutter 30CL-3 Dehorner Equipment Selection 30CL-1 Sheep Head Dropper Order Number 30CL-1 Hock Cutter 30CL-1

More information

JARVIS. Model JC IIIA (CE) Air Powered Dehider

JARVIS. Model JC IIIA (CE) Air Powered Dehider Air Powered Dehider U.S. PATENT NO. 5,122,092 EUROPEAN PATENT NO. 0438982 EQUIPMENT SELECTION JC IIIA Complete Blade Set Blade Diameter Operating Pressure 4034032 3023004 100 mm 90 psi 4034033 3023011

More information

JARVIS. Model 50G Hydraulic Dehorner

JARVIS. Model 50G Hydraulic Dehorner Hydraulic Dehorner EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page 50G Dehorner Electric Triggers Offset Blades... 4025011 Cup Blades... 4025047 Air Triggers Offset Blades... 4025025 Cup

More information

JARVIS. Model Hydraulic Cutter EQUIPMENT... TABLE OF

JARVIS. Model Hydraulic Cutter EQUIPMENT... TABLE OF Model 425-16 Hydraulic Cutter Standard Handles Pistol Grip and D Handle EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page Model 425--16 Cutter Standard Handles... 4025072 Pistol Grip and D

More information

JARVIS. Model JC IV Air Powered Dehider SET OPERATING PRESSURE TO PSI

JARVIS. Model JC IV Air Powered Dehider SET OPERATING PRESSURE TO PSI Model JC IV Air Powered Dehider SET OPERATING PRESSURE TO 45--55 PSI U.S. PATENT NO S: 5,122,092 & 7,163,453 EUROPEAN PATENT NO. 0438982 other patents pending EQUIPMENT SELECTION JC IV with 110mm Blade...

More information

JARVIS. Model 30CL-1 and 30CL-3 Hock Cutter and Dehorner

JARVIS. Model 30CL-1 and 30CL-3 Hock Cutter and Dehorner Model 30CL-1 and 30CL-3 Hock Cutter and Dehorner 30CL--1 Hock Cutter 30CL--1 Pistol Grip 30CL--3 Dehorner EQUIPMENT SELECTION... Ordering No. 30CL--1 Hock Cutter... 4025013 30CL--1 Hock Cutter with Grabber

More information

JARVIS. Model 30CL-ABC Beef Aitch Bone Cutter

JARVIS. Model 30CL-ABC Beef Aitch Bone Cutter Model 30CL-ABC Beef Aitch Bone Cutter EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page 30CL--ABC Aitch Bone Cutter Front Entry... 4025102 Rear Entry... 4025111 Hydraulic Power Unit... 4027266

More information

JARVIS. Model AST -101 STUNNER TESTER

JARVIS. Model AST -101 STUNNER TESTER Model AST -101 STUNNER TESTER EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page Stunner Tester, 115V... 4016004 Stunner Tester, 230V... 4016005 Notice to Employer and Safety Director... 2 Notice

More information

JARVIS. Model Buster V (CE) Beef Splitting Band Saw

JARVIS. Model Buster V (CE) Beef Splitting Band Saw Model Buster V (CE) Beef Splitting Band Saw EQUIPMENT SELECTION............. Ordering No. TABLE OF CONTENTS......................... Page Buster V Band Saw Shower Head.......... 4006049 Shower Head and

More information

JARVIS. Models USSS -1, USSS -2 and USSS -2A Pneumatic Stunners

JARVIS. Models USSS -1, USSS -2 and USSS -2A Pneumatic Stunners \ Models USSS -1, USSS -2 and USSS -2A Pneumatic Stunners Rear Handle for Knocker Box USSS--2A Side Handle for Knocker Box USSS--1 U.S. Patent No. 6,135,871 Patents Pending Worldwide Rear Handle for V

More information

JARVIS. Model VC Poultry Vent Cutter

JARVIS. Model VC Poultry Vent Cutter Poultry Vent Cutter EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page Package... 4302008... 4302007 Balancer... 1350084 Air Control Circuit... 3350006 Vacuum Hose (8 ft.)... 1323010 Air Hose

More information

JARVIS. Model FLS 1. Automatic First Leg Shear ... U.S. Patent Nos. 5,433,659 and 5,514,031 EQUIPMENT TABLE OF

JARVIS. Model FLS 1. Automatic First Leg Shear ... U.S. Patent Nos. 5,433,659 and 5,514,031 EQUIPMENT TABLE OF Automatic First Leg Shear U.S. Patent Nos. 5,433,659 and 5,514,031 EQUIPMENT SELECTION.......... Ordering No. TABLE OF CONTENTS............................ Page Right Hand........... 4025051 Left Hand.............

More information

JARVIS. Model SHC 140, 165, 165B, 165G, 165GT & 205 Hydraulic Circular Saw SHC 165 ERGONOMIC SHC 165 SHC 165B SHC 165G SHC 165GT TABLE OF EQUIPMENT

JARVIS. Model SHC 140, 165, 165B, 165G, 165GT & 205 Hydraulic Circular Saw SHC 165 ERGONOMIC SHC 165 SHC 165B SHC 165G SHC 165GT TABLE OF EQUIPMENT Model SHC 140, 165, 165B, 165G, 165GT & 205 Hydraulic Circular Saw SHC 165 ERGONOMIC SHC 165 SHC 165B US Patents: 6,511,483 6,805,696 SHC 165G SHC 165GT EQUIPMENT SELECTION... Ordering No. Model SHC 140...

More information

JARVIS MODEL VC BEEF BUNG DROPPER

JARVIS MODEL VC BEEF BUNG DROPPER MODEL VC BEEF BUNG DROPPER EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page Without Water 4022001 With Water... 4022031 Vacuum System 460/230V 60HZ... 4039002 400/230V 50HZ... 4039003 Sanitizer...

More information

SC-400, SC-550, SC-650 INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK

SC-400, SC-550, SC-650 INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK REV D: 0/8 INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK IMPORTANT: READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS TOOL. ALL PURPOSE BREAKING SAW

More information

SD Bendix E-10PR Retarder Control Brake Valve DESCRIPTION. OPERATION - Refer to Figure 2

SD Bendix E-10PR Retarder Control Brake Valve DESCRIPTION. OPERATION - Refer to Figure 2 SD-03-832 Bendix E-10PR Retarder Control Brake Valve MOUNTING PLATE SUPPLY 4 PORTS ELECTRICAL AUXILIARY DESCRIPTION TREADLE RETARDER CONTROL SECTION EXHAUST DELIVERY 4 PORTS FIGURE 1 - E-10PR RETARDER

More information

PNEUMATIC SLIDING VALVE

PNEUMATIC SLIDING VALVE INSTALLATION, OPERATION, & #: MM-SV001 6-23-09 Rev. A Page 1 of 8 PNEUMATIC SLIDING VALVE PART NUMBERS (Including, but not inclusive) SV704MSTS, SV714MSTS, SV754MSTS, SV764MSTS, SV774MSTS, SV706MSTS, SV716MSTS,

More information

operating instruction

operating instruction operating instruction a.560pn #125101 DE, EN, FR, SE Table of Contents Installation... 3 Tool use...4-5 Safety precautions...6-7 Troubleshooting and maintenance... 8 Technical specification... 9 Spare

More information

Flowserve Spring Diaphragm Rotary Actuators

Flowserve Spring Diaphragm Rotary Actuators Flow Control Division Installation, Operation, Maintenance Instructions Flowserve Spring Diaphragm Rotary Actuators TERMS CONCERNING SAFETY The safety terms DANGER, WARNING, CAUTION and NOTE are used in

More information

Tooling Assistance Center

Tooling Assistance Center Safeguards are designed into this application equipment to protect operators and maintenance personnel from most hazards during equipment operation. However, certain safety precautions must be taken by

More information

USER INSTRUCTIONS. Spring Diaphragm Rotary Actuators. Installation Operation Maintenance. Experience In Motion FCD VLAIM /12

USER INSTRUCTIONS. Spring Diaphragm Rotary Actuators. Installation Operation Maintenance. Experience In Motion FCD VLAIM /12 USER INSTRUCTIONS Spring Diaphragm Rotary Actuators FCD VLAIM050-01 05/12 Installation Operation Maintenance Experience In Motion Contents General Information 3 Unpacking 4 Installation 4 Changing Air

More information

Operating Manual. FloorMaster FS Flooring Stapler A18201 READ ALL SAFETY INSTRUCTIONS

Operating Manual. FloorMaster FS Flooring Stapler A18201 READ ALL SAFETY INSTRUCTIONS Operating Manual FloorMaster FS Flooring Stapler READ ALL SAFETY INSTRUCTIONS items included with tool INCLUDED WITH TOOL Plastic Case Tool Manual Safety Glasses Pneumatic Tool Oil Hex Key x 3 ACCESSORIES

More information

Service Manual Air Tech Second Stage

Service Manual Air Tech Second Stage Service Manual Air Tech Second Stage Copyright 2002, Cressi-sub Revised 3/2002 2 Air Tech Second Stage Service Manual Contents BEFORE STARTING... 3 DISASSEMBLY... 3 PARTS CLEANING AND LUBRICATION... 9

More information

SCISSOR LIFT Model MR6K-38 /161108A 6,000lb Capacity Operation Manual

SCISSOR LIFT Model MR6K-38 /161108A 6,000lb Capacity Operation Manual SCISSOR LIFT Model MR6K-38 /161108A 6,000lb Capacity Operation Manual (Version A) 2009. Apr. CONTENT 1. Safety Note, Caution and Warning Important Information Safety Instructions 2. Technical Manual Product

More information

OPTIMIZER TM OPERATOR MANUAL. Author: Labrie. Release Date: 1/31/07. Part #: 90320

OPTIMIZER TM OPERATOR MANUAL. Author: Labrie. Release Date: 1/31/07. Part #: 90320 OPTIMIZER TM OPERATOR MANUAL Author: Labrie Release Date: 1/31/07 Part #: 90320 Table of Contents Introduction Introducing the Optimizer TM... 1 Product Overview... 1 Contacting Labrie Environmental Group...

More information

OpTK. Product Instruction Manual. Spring Cylinder Rotary Actuators INTRODUCTION SAFETY INFORMATION INSTALLATION. Leading Technologies For Control

OpTK. Product Instruction Manual. Spring Cylinder Rotary Actuators INTRODUCTION SAFETY INFORMATION INSTALLATION. Leading Technologies For Control Leading Technologies For Control Product Instruction Manual OpTK Spring Cylinder Rotary Actuators TABLE OF CONTENTS INTRODUCTION Safety Information... pg. 1 Unpacking... pg. 1 INSTALLATION... pg. 1 PREVENTIVE

More information

Martin Air Cannon Maintenance Instructions

Martin Air Cannon Maintenance Instructions Martin Air Cannon Maintenance Instructions Go to Martin Air Cannon Maintenance Instructions web page Martin Hurricane Air Cannon Martin Tornado Air Cannon Operator s Manual M3747 Important MARTIN ENGINEERING

More information

INSTRUCTIONS. Disassembly. Shifter Cam Assembly. Shifter Forks

INSTRUCTIONS. Disassembly. Shifter Cam Assembly. Shifter Forks INSTRUCTIONS Disassembly To protect against accidental start-up of vehicle, always disconnect the negative battery cable before working on the motorcycle. Failure to disconnect the battery cable could

More information

PRESSURE RELIEF VALVE: DISASSEMBLY, INSPECTION, and ASSEMBLY CONTENTS

PRESSURE RELIEF VALVE: DISASSEMBLY, INSPECTION, and ASSEMBLY CONTENTS Page 1 of 35 PRESSURE RELIEF VALVE: DISASSEMBLY, INSPECTION, and ASSEMBLY CONTENTS 1. Overview 2. Disassembly of Valves with Liner Subs and press-in Bushing (Models 30525 and 30550). 2.1. Routine Disassembly

More information

Service Manual Air Plus Second Stage

Service Manual Air Plus Second Stage Service Manual Air Plus Second Stage Includes XS Series Second Stage Copyright 2002, Cressi-sub Revised 3/2002 2 Air Plus Second Stage Service Manual Contents BEFORE STARTING... 3 DISASSEMBLY... 3 PARTS

More information

GPS Steering System Installation Manual

GPS Steering System Installation Manual GPS Steering System Installation Manual Supported Vehicles Challenger Massey Ferguson AGCO MT-645C, MT-645D MF-8650 DT-205B MT-655C, MT-655D MF-8660 DT-225B MT-665C, MT-665D MF-8670 DT-250B MT-675C, MT-675D

More information

Valtek Auxiliary Handwheels and Limit Stops

Valtek Auxiliary Handwheels and Limit Stops Valtek Auxiliary s and Limit Stops Table of Contents Page 1 General information 2 Installation 2 Side-mounted handwheels, size 25 and 50 (linear actuators) 3 Side-mounted handwheels, size 100 and 200 (linear

More information

REV A: 02/15 BUNG GUN VACUUM SYSTEM INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK

REV A: 02/15 BUNG GUN VACUUM SYSTEM INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK BUNG GUN VACUUM SYSTEM INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK IMPORTANT: READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS TOOL. TOOL DATA MODEL:

More information

OWNER S MANUAL MODEL # TGL-500 HITCH LIFT

OWNER S MANUAL MODEL # TGL-500 HITCH LIFT OWNER S MANUAL MODEL # TGL-500 HITCH LIFT For Customer Service Call or Fax 1 (800) 87-LARIN 1 SPECIFICATIONS.. Max Capacity:.500 lbs. Motor Power: 12 VDC SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

More information

On-A-Roll Lifter Instruction Manual for Standard Models Read Before Use!

On-A-Roll Lifter Instruction Manual for Standard Models Read Before Use! On-A-Roll Lifter Instruction Manual for Standard Models Read Before Use! Important instructional, safety and precautionary information! It is the user s responsibility to exercise good judgment, common

More information

Service Jacks. Operating Instructions & Parts Manual. Model Number. Capacity 4 Ton 4 Ton Air/ Manual 10 Ton 10 Ton Air/ Manual HW93657/ HW93660

Service Jacks. Operating Instructions & Parts Manual. Model Number. Capacity 4 Ton 4 Ton Air/ Manual 10 Ton 10 Ton Air/ Manual HW93657/ HW93660 Service Jacks Operating Instructions & Parts Manual Model Number HW93657 HW93667 HW93660 HW93662 Capacity 4 Ton 4 Ton Air/ Manual 10 Ton 10 Ton Air/ Manual Made in North America HW93657/ HW93660 HW93667/

More information

Instruction Manual For Auto Shift Hydraulic Lift Table

Instruction Manual For Auto Shift Hydraulic Lift Table Instruction Manual For Auto Shift Hydraulic Lift Table Model Number: CART-550-AS Note: Owner/Operator must read and understand this Instruction Manual before operating the lift & tilt table. Contents 1

More information

500kg HYDRAULIC TABLE LIFT

500kg HYDRAULIC TABLE LIFT Product Code: 6007T OWNER S MANUAL PRODUCT CODE: 6007T 500kg HYDRAULIC TABLE LIFT Working Load Limit 500kg Maximum Height 1575mm Minimum Height 440mm Table Dimensions 1010x520mm Wheel Diameter 150mm Made

More information

Page 1 of 26 Oteco Inc. Houston, Texas

Page 1 of 26 Oteco Inc. Houston, Texas Page 1 of 26 Page 2 of 26 1.0 OVERVIEW CONTENTS 2.0 INSTALLATION GUIDELINES 2.1 Preferred Valve Orientation 2.2 Pressure Rating and Orientation of Discharge line 2.3 Reaction Forces and Anchoring of Reset

More information

***Be sure that the loaded trailer weight does not exceed 24,000 lbs. or the vertical load rating does not exceed 6000 lbs.

***Be sure that the loaded trailer weight does not exceed 24,000 lbs. or the vertical load rating does not exceed 6000 lbs. April 2006 INSTALLATION INSTRUCTIONS MODEL NO. 70680 07068 24K 5th Wheel with Heavy Duty EZ-ROLLER For use on shortbed P/U applications US Pat. No. 6247720 PARTS INCLUDE: 1. 1675-07 Head Assembly (1) 15.

More information

STRUT SPRING COMPRESSOR

STRUT SPRING COMPRESSOR OWNER S MANUAL PRODUCT CODE: 1221T STRUT SPRING COMPRESSOR Capacity Stroke Spring Coil Spring Spring Coil Net Weight (Maximum) Thickness Length Diameter 1,000kg 330mm 10-18mm 210-570mm 100-158mm 36kg Made

More information

GH-BETTIS SERVICE INSTRUCTIONS DISASSEMBLY & REASSEMBLY FOR MODELS HD521-M4, HD721-M4 AND HD731-M4 DOUBLE ACTING SERIES PNEUMATIC ACTUATORS

GH-BETTIS SERVICE INSTRUCTIONS DISASSEMBLY & REASSEMBLY FOR MODELS HD521-M4, HD721-M4 AND HD731-M4 DOUBLE ACTING SERIES PNEUMATIC ACTUATORS GH-BETTIS SERVICE INSTRUCTIONS DISASSEMBLY & REASSEMBLY FOR MODELS HD521-M4, HD721-M4 AND HD731-M4 DOUBLE ACTING SERIES PNEUMATIC ACTUATORS WITH HYDRAULIC CONTROL PACKAGE PART NUMBER: SE-023 REVISION:

More information

EZ LINER EXPRESS USERS MANUAL

EZ LINER EXPRESS USERS MANUAL EZ LINER EXPRESS 2013 Vehicle Service Group CHIEF'S LIMITED ONE-YEAR WARRANTY & LIABILITY Chief Automotive Technologies warrants for one year from date of installation and/or purchase any components of

More information

Encore Manual Powder Spray Gun Trigger Switch Replacement

Encore Manual Powder Spray Gun Trigger Switch Replacement Instruction Sheet P/N 1096694A Encore Manual Powder Spray Gun Trigger Switch Replacement Preparation 1. Remove the nozzle nut, nozzle, and electrode assembly. 2. Disconnect the powder feed hose adapter,

More information

INSTRUCTIONS AND PARTS LIST FOR MODEL 125H & 150H HAND-OPERATED HYDRAULIC PRESS

INSTRUCTIONS AND PARTS LIST FOR MODEL 125H & 150H HAND-OPERATED HYDRAULIC PRESS INSTRUCTIONS AND PARTS LIST FOR MODEL 125H & 150H HAND-OPERATED HYDRAULIC PRESS SETTING UP THE PRESS FOR OPERATION For shipping convenience, the gauge, pump handle, hoist crank, screw nose and base angles

More information

Valtek Spring Cylinder Linear Actuators

Valtek Spring Cylinder Linear Actuators Valtek Linear Actuators GENERAL INFORMATION The following instructions are designed to assist in installing, troubleshooting and servicing Valtek spring cylinder actuators. Product users and maintenance

More information

DO NOT INSTALL, OPERATE, OR MAINTAIN AN ATI PRODUCT UNLESS TRAINED AND QUALIFIED IN PRODUCT AND ACCESSORY INSTALLATION, OPERATION AND MAINTENANCE.

DO NOT INSTALL, OPERATE, OR MAINTAIN AN ATI PRODUCT UNLESS TRAINED AND QUALIFIED IN PRODUCT AND ACCESSORY INSTALLATION, OPERATION AND MAINTENANCE. IOM Supplement IOMS003 ATI HO1/HO2 HYDRAULIC OVERRIDE Scope of Supplement This supplement is intended to assist those who are involved with the installation, operation and maintenance of ATI Linear Actuators

More information

Operating Instructions 20 Ton Air/Hydraulic Service Jack

Operating Instructions 20 Ton Air/Hydraulic Service Jack MODEL: 3225 Operating Instructions 20 Ton Air/Hydraulic Service Jack WARNING: Important: Read these instructions and all warnings prior to using this equipment. Understand all operating procedures, safety

More information

W & A 12 ROW TOP LEVELING STACKER LEVEL BANDER

W & A 12 ROW TOP LEVELING STACKER LEVEL BANDER W & A 12 ROW TOP LEVELING STACKER LEVEL BANDER NO. 3640 OPERATOR S MANUAL TO THE OWNER: Congratulations on your purchase of a new W & A Top Leveling Stacker Level Bander. Your selection is an indication

More information

BIG BLASTER Air Cannon Maintenance Instructions

BIG BLASTER Air Cannon Maintenance Instructions BIG BLASTER Air Cannon Maintenance Instructions Go to BIG BLASTER Air Cannon Maintenance Instructions web page BIG BLASTER HURRICANE Air Cannon BIG BLASTER XHV Air Cannon with MARTIN TORNADO Exhaust Valve

More information

Before equipment use, please read this operation manual carefully. Serial Number: Date Purchased:

Before equipment use, please read this operation manual carefully. Serial Number: Date Purchased: Pushed & Geared Trolleys OPERATION MANUAL This operation manual is intended as an instruction manual for trained personnel who are in charge of installation, maintenance, repair etc. Before equipment use,

More information

Instruction Manual. BS Series

Instruction Manual. BS Series Instruction Manual BS Series NOTE: Owner/Operator must read and understand this instruction manual before using the lift table. RevB: 02/2009 1 Operation and Service Manual BEFORE OPERATING THE LIFT TABLE,

More information

TABLE OF CONTENTS. Ram Assembly

TABLE OF CONTENTS. Ram Assembly TABLE OF CONTENTS DUC Cover------------------------------------------------------------------------------------ 00 Table of Contents----------------------------------------------------------------------------

More information

CONTENTS: 5740AH - 40 Ton Air/Hydraulic Shop Press 5750AH - 50 Ton Air/Hydraulic Shop Press OWNER'S MANUAL

CONTENTS: 5740AH - 40 Ton Air/Hydraulic Shop Press 5750AH - 50 Ton Air/Hydraulic Shop Press OWNER'S MANUAL OWNER'S MANUAL CONTENTS: Page 1 Specifications 2 Safety Information and Warranty Information 3 Parts List 4-6 Assembly Instructions 7 Pump and Ram Assembly Instructions 8 Procedure for Bleeding Air 9 Pump

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS GMT 560 (4500/5500) CREW CAB (2351A000) Link Mfg. Ltd. 223 15th St. N.E. Sioux Center, IA USA 51250-2120 The CABMATE MODEL 2351A000 fits the 2003 and later GM 4500 / 5500 crew

More information

DISPLACEMENT PUMP INSTRUCTIONS-PARTS LIST Rev. K. Model , Series A Model , Series B Model , Series A

DISPLACEMENT PUMP INSTRUCTIONS-PARTS LIST Rev. K. Model , Series A Model , Series B Model , Series A INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. DISPLACEMENT PUMP 308190 Rev. K 3000 psi (210 bar) MAXIMUM WORKING PRESSURE Model

More information

AUG 18 Rev M

AUG 18 Rev M ORIGINAL INSTRUCTIONS 626 Pneumatic Tooling Assemblies 189721-[ ] and 189722-[ ] Customer Manual 409-5862 06 AUG 18 Rev M SAFETY PRECAUTIONS AVOID INJURY READ THIS FIRST!... 2 1. INTRODUCTION... 4 2. DESCRIPTION...

More information

Installation Guide VHM Wall Mount Kit for Philips MX600/700/800 and MP60/70 IntelliVue

Installation Guide VHM Wall Mount Kit for Philips MX600/700/800 and MP60/70 IntelliVue Installation Guide VHM Wall Mount Kit for Philips MX600/700/800 and MP60/70 IntelliVue The purpose of this guide is to: 1. Describe attachment of Table Top Mount to Mounting Adapter (page 2). 2. Describe

More information

Eclipser 2500/2800 OPERATING MANUAL. and Continuous Coil (CC) Clipping System. ENCORE (EA) ECLIPSER 2500 and 2800 SERIES

Eclipser 2500/2800 OPERATING MANUAL. and Continuous Coil (CC) Clipping System. ENCORE (EA) ECLIPSER 2500 and 2800 SERIES Eclipser 2500/2800 and Continuous Coil (CC) Clipping System Encore Eclipser 2500 Series (Green) Hartco Eclipser 2500 (Black) not shown OPERATING MANUAL ENCORE (EA) ECLIPSER 2500 and 2800 SERIES Pneumatic

More information

INSTRUCTIONS AND PARTS LIST FOR MODEL 25H HAND-OPERATED HYDRAULIC PRESS

INSTRUCTIONS AND PARTS LIST FOR MODEL 25H HAND-OPERATED HYDRAULIC PRESS INSTRUCTIONS AND PARTS LIST FOR MODEL 25H HAND-OPERATED HYDRAULIC PRESS SETTING UP THE PRESS FOR OPERATION For shipping convenience, the gauge, pump handle, hoist crank, screw nose and base angles were

More information

OLYMPIAN MODEL 740 Operation and Service Manual

OLYMPIAN MODEL 740 Operation and Service Manual OLYMPIAN MODEL 740 Operation and Service Manual P/N 133911-102 FCI MANUAL P/N 133865-001 Data herein has been verified and validated and believed adequate for the intended use. If the machine or procedures

More information

BRAKES. Section III REAR AXLE DATA AND SPECIFICATIONS HAND BRAKE CHRYSLER SERVICE MANUAL BRAKES 17

BRAKES. Section III REAR AXLE DATA AND SPECIFICATIONS HAND BRAKE CHRYSLER SERVICE MANUAL BRAKES 17 BRAKES 17 There is no basic design change in the rear axle and sure grip differential except the larger diameter pinion shaft is now used on all models for 1959. The Service Procedures will remain the

More information

SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE

SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE Cable Processor Module overview WARNING! When tipping the Cable Processor Module back, (after removing the toggle arm pin), use extreme caution not to drop

More information

PREVIOUS GENERATION. Encore Manual Powder Spray Gun Trigger Switch Replacement. Introduction. Preparation. Gun Disassembly

PREVIOUS GENERATION. Encore Manual Powder Spray Gun Trigger Switch Replacement. Introduction. Preparation. Gun Disassembly Instruction Sheet P/N 1102249A Encore Manual Powder Spray Gun Trigger Switch Replacement Introduction Preparation Gun Disassembly The Encore trigger switch has been redesigned to eliminate the notches

More information

CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. Instruction Manual Notes: Page Manual Conventions This manual uses the following symbols to help differentiate between different kinds of information. The safety symbol is used with a key word to alert

More information

490 Series Actuators. 490 Series. Contents. Introduction

490 Series Actuators. 490 Series. Contents. Introduction Instruction Manual Form 049 May 1992 490 Series 490 Series Actuators Contents Introduction.............................. 1 Scope of Manual............................. 1 Description..................................

More information

351GF-15. Hydrant Coupler INSTALLATION / OPERATION / MAINTENANCE MODEL

351GF-15. Hydrant Coupler INSTALLATION / OPERATION / MAINTENANCE MODEL INSTALLATION / OPERATION / MAINTENANCE MODEL 351GF-15 Hydrant Coupler 351GF-15 Hydrant Coupler This installation/operation/maintenance guide is designed to provide instructions for the installation operation

More information

STEERING COLUMN - TILT

STEERING COLUMN - TILT STEERING COLUMN - TILT 1994 Toyota Celica 1994 STEERING Toyota - Steering Column - Tilt Wheel Celica DESCRIPTION & OPERATION Tilt steering wheels incorporate a mainshaft, attached by a "U" joint to an

More information

SD Bendix E-7 Dual Brake Valve DESCRIPTION OPERATION APPLYING: NORMAL OPERATION - PRIMARY CIRCUIT PORTION

SD Bendix E-7 Dual Brake Valve DESCRIPTION OPERATION APPLYING: NORMAL OPERATION - PRIMARY CIRCUIT PORTION SD-03-818 Bendix E-7 Dual Brake Valve DESCRIPTION The Bendix E-7 dual brake valve is a suspended, pedal-operated type brake valve with two separate supply and delivery circuits for service and emergency

More information

Operation & Technical Manual. Model: Ground Test Motor

Operation & Technical Manual. Model: Ground Test Motor Operation & Technical Manual Model: 13-6604-6600 Ground Test Motor 05/2009 Rev. 05 Includes Illustrated Parts Lists DEVELOPED IN CONJUNCTION WITH HAMILTON-SUNDSTRAND 1740 Eber Rd Tronair, Inc. Phone: (419)

More information

USER INSTRUCTIONS FOR OPERATION & MAINTENANCE 4068 Pneuma c / Hydraulic Installa on Tool

USER INSTRUCTIONS FOR OPERATION & MAINTENANCE 4068 Pneuma c / Hydraulic Installa on Tool Additional copies of this manual are available at: USER INSTRUCTIONS FOR OPERATION & MAINTENANCE 4068 Pneuma c / Hydraulic Installa on Tool 4068 Hydro-Pneumatic Blind Rivet Nut and Stud Installation Tool

More information

INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS D SERIES TABLE OF CONTENTS

INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS D SERIES TABLE OF CONTENTS INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS D SERIES GENERAL INFORMATION TERMS CONCERNING SAFETY UNPACKING INSTALLATIONS VALVE MAINTENANCE TABLE OF CONTENTS VALVE DISASSEMBLY AND REASSEMBLY PLUG

More information

INSTRUCTIONS AND PARTS LIST FOR Models 8-025, 8-050, 8-075, and Elec-Draulic II Presses

INSTRUCTIONS AND PARTS LIST FOR Models 8-025, 8-050, 8-075, and Elec-Draulic II Presses INSTRUCTIONS AND PARTS LIST FOR Models 8-025, 8-050, 8-075, and 8-150 Elec-Draulic II Presses SETTING UP THE PRESS FOR OPERATION For shipping convenience some of the parts are not assembled. Assemble these

More information

Provided by: Operating, Maintenance & Parts Manual

Provided by:   Operating, Maintenance & Parts Manual Provided by: www.hoistsdirect.com TB681.qxd 11/29/2004 3:04 PM Page 1 Operating, Maintenance & Parts Manual TB603 Manually Lever Operated Chain Hoist 1100 POUNDS MAXIMUM CAPACITY (500 kg) Follow all instructions

More information

OPERATION MANUAL 17 Crown Block Sheave Manufactured by Wireline Technologies, Inc. Serial Number

OPERATION MANUAL 17 Crown Block Sheave Manufactured by Wireline Technologies, Inc. Serial Number OPERATION MANUAL 17 Crown Block Sheave Manufactured by Wireline Technologies, Inc. Serial Number Introduction This manual explains the use and care of 17 Crown Block Sheaves manufactured by Wireline Technologies,

More information

ACI Hoist & Crane. Festoon System. 689 S.W. 7th Terrace Dania, FL (954) Fax (954) Toll Free A-HOIST ( )

ACI Hoist & Crane. Festoon System. 689 S.W. 7th Terrace Dania, FL (954) Fax (954) Toll Free A-HOIST ( ) ACI Hoist & Crane Festoon System 689 S.W. 7th Terrace Dania, FL 33004 (954) 921-1171 Fax (954) 921-7117 Toll Free 1-888-4-A-HOIST (1-888-424-6478) www.acihoist.com 2 Standard Duty C-Track Index 1. General

More information

ASSEMBLY & OPERATION INSTRUCTION MANUAL

ASSEMBLY & OPERATION INSTRUCTION MANUAL Sliding Bridge Jack 3,500 lbs. Capacity ASSEMBLY & OPERATION INSTRUCTION MANUAL TABLE OF CONTENTS Specifications... 2 Description & Features... 3 Installation Instructions... 4 Safety Instructions... 4

More information

GPS AutoSteer System Installation Manual

GPS AutoSteer System Installation Manual GPS AutoSteer System Installation Manual Supported Vehicles Case STX Wheeled or Quadtrack Case STEIGER Wheeled or Quadtrack New Holland TJ New Holland T 380 380 380 9030 430 385 430 9040 480 430 480 9050

More information

Air Operated End Lift

Air Operated End Lift Air Operated End Lift Operating Instructions & Parts Manual Model Number HW93690 Capacity 10 Ton Made in the USA SAVE THESE INSTRUCTIONS For your safety, read, understand, and follow the information provided

More information

RETROFIT INSTALLATION

RETROFIT INSTALLATION RETROFIT INSTALLATION Installation Instructions C0013536 Pallet Grip Q Series Semi-Automatic Machines Manufacture Date before July, 2010 1 RETROFIT INSTALLATION Table of Contents 1.0 Introduction... 3

More information

W & A 12 ROW TOP LEVELING STACKER LEVEL BANDER

W & A 12 ROW TOP LEVELING STACKER LEVEL BANDER W & A 12 ROW TOP LEVELING STACKER LEVEL BANDER NO. 3640 OPERATOR S MANUAL TO THE OWNER: Congratulations on your purchase of a new W & A Top Leveling Stacker Level Bander. Your selection is an indication

More information

Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3

Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage

More information

Installation, Operation, and Maintenance Instructions for Bettis RGS F-Series Spring-Return (SR) Actuators

Installation, Operation, and Maintenance Instructions for Bettis RGS F-Series Spring-Return (SR) Actuators Part Number: RGS011110-3, Rev. 0 Release: November 2015 Installation, Operation, and Maintenance Instructions for Bettis RGS F-Series Spring-Return (SR) Actuators Part Number: RGS011110-3, Rev. 0 Table

More information

Instruction Manual BS50D

Instruction Manual BS50D Instruction Manual BS50D NOTE: Owner/Operator must read and understand this instruction manual before using the lift table. 1 Operation and Service Manual BEFORE OPERATING THE LIFT TABLE, READ THIS MANUAL

More information

PRODUCT SERVICE MANUAL FOR BK12DHZ PUMPS

PRODUCT SERVICE MANUAL FOR BK12DHZ PUMPS PRODUCT SERVICE MANUAL FOR BK12DHZ PUMPS WARNING This manual, and the GENERAL INSTRUCTION MANUAL SRM00046, should be read thoroughly prior to pump installation, operation or maintenance. Manual No. SRM00095

More information

<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W

<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W B&W Trailer Hitches 1216 Hawaii Rd / PO Box 186 Humboldt, KS 66748 Turnoverball Gooseneck Hitch Installation Instructions MODEL 1314 2013 2014 RAM 3500

More information

Installation, Operation and Maintenance Manual RGS Rev. 0 November Bettis RGS F-Series Spring-Return Actuators

Installation, Operation and Maintenance Manual RGS Rev. 0 November Bettis RGS F-Series Spring-Return Actuators Installation, Operation and Maintenance Manual RGS011110-3 Rev. 0 November 2015 Bettis RGS F-Series Spring-Return Actuators Installation, Operation and Maintenance Manual RGS011110-3 Rev. 0 Table of Contents

More information

ATV TRACK KIT. Operator s Manual Installation Instructions Service Instructions Replacement Parts List. Effective Date: October, 2012

ATV TRACK KIT. Operator s Manual Installation Instructions Service Instructions Replacement Parts List. Effective Date: October, 2012 p/n 2258-642 ATV TRACK KIT Operator s Manual Installation Instructions Service Instructions Replacement Parts List Track Assembly Kits (p/n 1436-204) Mounting Assembly Kits (p/n 1436-205) 1436-815) Effective

More information

3-Stage Under Axle Jack Weight: 69.5 kg (153 lbs.)

3-Stage Under Axle Jack Weight: 69.5 kg (153 lbs.) 655 Eisenhower Drive Owatonna, MN 55060-0995 USA Phone: (507) 455-7000 Tech. Serv.: (00) 533-627 Fax: (00) 955-329 Order Entry: (00) 533-627 Fax: (00) 23-665 International Sales: (507) 455-7223 Fax: (507)

More information

Product Description. Product Numbers. Warning/Caution Notations. Required Tools. Wiring. Prerequisites

Product Description. Product Numbers. Warning/Caution Notations. Required Tools. Wiring. Prerequisites Document No. 155-302N VE 598 Electronic Flowrite Valve Field Assembly Product Description The VE 598 Electronic Valve Assemblies consist of an electronic actuator, linkage kit, and a valve body assembly.

More information

Amarr SuperFlex. Installation Instructions and Owner's Manual. Entrematic 165 Carriage Court Winston Salem, NC

Amarr SuperFlex. Installation Instructions and Owner's Manual. Entrematic 165 Carriage Court Winston Salem, NC Entrematic 165 Carriage Court Winston Salem, NC 27105 www.amarr.com 877-512-6277 Amarr SuperFlex Installation Instructions and Owner's Manual Do not install, operate or service this product unless you

More information

Installation Guide Philips MP90 VHM Wall Mount Kit

Installation Guide Philips MP90 VHM Wall Mount Kit Installation Guide Philips MP90 VHM Wall Mount Kit The purpose of this guide is to describe the procedures for installing the MP90 VHM Wall Mount Kit. Table of Contents Section 1.0: Mounting the VHM-Series

More information

Hydraulic Air Pump. Operating Instructions & Parts Manual. Capacity 10,000 PSI. Model Number Atd-5812

Hydraulic Air Pump. Operating Instructions & Parts Manual. Capacity 10,000 PSI. Model Number Atd-5812 Hydraulic Air Pump Operating Instructions & Parts Manual Model Number Atd-5812 Capacity 10,000 PSI Atd Tools Inc. 2005 160 Enterprise Drive, Wentzville, MO 63385 Atd5812-M0 Printed in Taiwan Save these

More information

I & M Mark 78 Series. Ideal Installation. Start-Up. Installation & Maintenance Instructions for Mark 78 Control Valves (1-1/2-2 )

I & M Mark 78 Series. Ideal Installation. Start-Up. Installation & Maintenance Instructions for Mark 78 Control Valves (1-1/2-2 ) I & M Mark 8 Series 0 Wasson Road Cincinnati, OH 4509 USA Phone 5-5-5600 Fax 5-8-005 info@richardsind.com www.jordanvalve.com Installation & Maintenance Instructions for Mark 8 Control Valves (-/ - ) Warning:

More information

1500 Series Roll Off Hoist. Owner s Manual (5-06)

1500 Series Roll Off Hoist. Owner s Manual (5-06) 1500 Series Roll Off Hoist Owner s Manual (5-06) Section 1: General Information Introduction Safety Information Warranty Information Table of Contents Section 2: Operation Operating the P.T.O. Operating

More information