NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: August 2009
|
|
- Beverley Briggs
- 5 years ago
- Views:
Transcription
1 NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: August 2009 SUBJECT: CYLINDERHEADCOOLANTVENTLINE ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page Number(s) DDC-SVC-MAN-0026 EPA07 MBE Cylinder Head Coolant Vent Line New Section Insert after 4.5 NOTE: Page numbers are based on the most recent version of the individual publication and may be adjusted throughout the annual print cycle.
2 REMOVAL OF CYLINDER HEAD COOLANT VENT LINE Remove as follows: 1. Drain the cooling system. 2. Remove air cleaner assembly. 3. Remove the radiator support bracket from the top of the EGR cooler bracket and radiator. 4. Disconnect the coolant vent line located on top of the EGR cooler by removing the banjo bolt and seal rings. Discard the seal rings. 5. Remove the bolt securing the air compressor suction supply bracket to the EGR cooler bracket. See Figure 1. Figure 1 Air Compressor Suction Supply Bracket 6. Remove the two bolts securing the turbocharger inlet elbow to the EGR cooler bracket. Rotate the turbocharger inlet elbow away from the engine. NOTE: Do not remove the turbocharger air inlet elbow. 7. Remove the clamp halves securing the exhaust gas inlet pipe to the EGR cooler and to the center pipe of the exhaust manifold. Remove the exhaust gas inlet pipe. 8. Remove the EGR cooler gas outlet pipe. Refer to section "Removal of EGR Cooler Gas Outlet Pipe." 9. Remove the EGR control valve. Refer to section "Removal of EGR Control Valve." 10. Remove the EGR cooler straps. See Figure 2.
3 11. Disconnect the upper coolant inlet pipe from the lower coolant inlet pipe. See Figure Clamp 6. EGR Cooler Straps 2. Exhaust Gas Inlet Pipe 7. Coolant Vent Line Connection 3. Exhaust Heat Shield Bracket 8. EGR Cooler Bracket 4. Exhaust Heat Shield 9. Lower Coolant Pipe 5. EGR Cooler 10. Upper Coolant Pipe Figure 2 EGR Cooler 12. Pull the EGR cooler straight up from the EGR cooler support bracket. See Figure 2. EYE INJURY To avoid injury from flying debris, wear a face shield or goggles. NOTE: Remove only enough material to allow a socket to fit on the banjo bolts.
4 13. Using a die grinder or other suitable device, remove material from the EGR cooler support bracket as shown in Figure 3. Do not remove cylinder head covers before this modification. Figure 3 EGR Cooler Support Bracket 14. Remove shavings and clean cylinder head area, taking care not to allow metal shavings into any part of the engine. 15. Remove the cylinder head covers from cylinders 1-4. Refer to section "Removal of Cylinder Head Cover." 16. Remove the injector harness adaptor frames from cylinders 1-4. Refer to section "Removal of Fuel Injector HarnessAdaptorFrame."
5 17. Remove exhaust heat shield. See Figure Exhaust Manifold Heat Shield 4. Injector Harness Adaptor Frame/Cylinder Head cover Mounting Studs 2. Heat Shield Mounting Bolts 5. Cylinder Head Cover Cap Nuts 3. Injector Harness Adaptor Frame 6. Cylinder Head Cover Figure 4 Exhaust Manifold Heat Shield
6 NOTE: The lower exhaust mounting bolt cannot be fully removed with the exhaust manifold installed. Loosen the bolt enough to provide clearance for the coolant vent line to be removed. See Figure 5. Figure 5 Lower Heat Shield Bracket and Mounting Bolt 18. Remove the doser injector coolant line banjo bolt and seal rings from the #6 cylinder head connection. Discard seal rings. 19. Remove the six banjo bolts retaining the cylinder head coolant vent line.
7 20. Remove the cylinder head coolant vent line. Discard seal rings. See Figure Doser Injector Coolant Line 5. Coolant Vent Line Banjo Bolt (6 qty.) 2. Doser Injector Coolant Line Seal Rings 6. Coolant Vent Line 3. Doser Injector Coolant Line Banjo Bolt 7. Coolant Vent Line Banjo Bolt 4. Coolant Vent Line Seal Rings (15 qty.) 8. Banjo Union Figure 6 Coolant Vent Line
8 INSTALLATION OF CYLINDER HEAD COOLANT VENT LINE Install as follows: 1. Install the cylinder head coolant vent line using new seal rings. Torque the six banjo bolts to 35 N m (26 lb ft). 2. Install the doser injector coolant line to the #6 cylinder head connection using new seal rings. Torque the banjo bolt to N m (12-15 lb ft). 3. Install the exhaust heat shield. Torque heat shield bolts to 25 N m (18 lb ft). See Figure Exhaust Manifold Heat Shield 4. Injector Harness Adaptor Frame/Cylinder Head cover Mounting Studs 2. Heat Shield Mounting Bolts 5. Cylinder Head Cover Cap Nuts 3. Injector Harness Adaptor Frame 6. Cylinder Head Cover Figure 7 Exhaust Manifold Heat Shield 4. Install the injector harness adaptor frames for cylinders 1-4. Refer to section "Installation of Fuel Injector Harness Adaptor Frame." 5. Install the cylinder head covers for cylinders 1-4. Refer to section "Installation of Cylinder Head Cover." 6. Coat the EGR cooler coolant inlet and outlet connector pipes with International Product Corporation Rubber Lubricant Emulsion (P-80). See Figure 8.
9 NOTICE: During installation, ensure that the EGR cooler coolant pipes are seated correctly with the connector pipes. Improperly seated pipes will leak causing engine damage. 7. Install the EGR cooler. Secure the EGR cooler to the bracket with clamps. Torque the clamps to 10 N m (7 lb ft). See Figure Clamp 6. EGR Cooler Straps 2. Exhaust Gas Inlet Pipe 7. Coolant Vent Line Connection 3. Exhaust Heat Shield Bracket 8. EGR Cooler Bracket 4. Exhaust Heat Shield 9. Lower Coolant Pipe 5. EGR Cooler 10. Upper Coolant Pipe Figure 8 EGR Cooler 8. Rotate the turbocharger inlet elbow back into the correct position and secure the support bracket with two bolts. Torque the bolts to 35 N m (26 lb ft). 9. Properly align the coolant pipe and small support bracket to the water pump. Torque the bolts to 35 N m (26 lb ft). 10. Install the inlet gas pipe to EGR cooler and center pipe of exhaust manifold and secure with clamp halves. Torque clamp bolts to 25 N m (18 lb ft). 11. Install the EGR control valve. Refer to section "Installation of Installation of EGR Control Valve."
10 12. Install the EGR cooler gas outlet pipe. Refer to section "Installation of EGR Cooler Gas Outlet Pipe." 13. Install the coolant vent line to the top of the EGR cooler and secure with banjo bolts and washers. Torque banjo bolt to 25 N m (18 lb ft). 14. Install the air compressor suction pipe to the mounting bracket and secure with one M10 bolt. Torque the bolt to 35 N m (26 lb ft). See Figure 9. Figure 9 Air Compressor Suction Supply Bracket 15. Install the radiator support bracket from the top of the EGR cooler bracket and radiator. 16. Refill engine with coolant.
11
12 ADDITIONAL SERVICE INFORMATION Additional service information is available in Power Service Literature. Detroit Diesel, DDC, Series 60 and the spinning arrows design are registered trademarks of Detroit Diesel Corporation. Copyright 2009 Detroit Diesel Corporation. All rights reserved. Printed in U.S.A.
Section 7.3 Water Manifold has been updated.
NUMBER: 08 DD15-11 S.M. REF.: 7.3 ENGINE: DD15 DATE: September 2008 SUBJECT: WATER MANIFOLD PUBLICATION: DDC-SVC-MAN-0002 Section 7.3 Water Manifold has been updated. 7.3 WATER MANIFOLD Coolant flows from
More informationNUMBER: S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: July 2009
NUMBER: 7 4 09 S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: July 2009 SUBJECT: EXHAUST GAS RECIRCULATION COOLER WATER MANIFOLD ASSEMBLY ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section
More informationNUMBER: S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: October 2009
NUMBER: 10 09 09 S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: October 2009 SUBJECT: INTERMEDIATE FRAME / FUEL INJECTOR WIRING HARNESS ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section
More informationAdditions, Revisions, or Updates
1 8 22-13 SUBJECT DATE Water Manifold Assembly August 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Installation of the DD13 EGR Cooler Water DDC-SVC-MAN-0081
More informationEGR heater plate removal and installation procedure has been added.
NUMBER: 08 60-3 S.M. REF.: 8.3 ENGINE: EPA07 Series 60 DATE:June 2008 SUBJECT: EGR HEATER PLATE PUBLICATION: DDC-SVC-MAN-0005 EGR heater plate removal and installation procedure has been added. 8.3.1 REMOVAL
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA04 MBE 4000 DATE: April 2009
NUMBER: 4 8 09 S.M. REF.: Listed in Table ENGINE: EPA04 MBE 4000 DATE: April 2009 SUBJECT: CYLINDER HEAD INSTALLATION ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: April 2009
NUMBER: 4 7 09 S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: April 2009 SUBJECT: SPN 27 ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page Number(s) DDC-SVC-MAN-0009
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: DD15 DATE: March 2009
NUMBER: 3 3 09 S.M. REF.: Listed in Table ENGINE: DD15 DATE: March 2009 SUBJECT: FUEL FILTER ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page Number(s) DDC-SVC-MAN-0037
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: October 2012 SUBJECT: REFERENCES TO THE TURBOCHARGER PURGE ROUTINE
NUMBER: 10 01 12 S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: October 2012 SUBJECT: REFERENCES TO THE TURBOCHARGER PURGE ROUTINE ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform
More informationNUMBER: S.M. REF.: 8.5 ENGINE: EPA07 Series 60 DATE: November 2008
NUMBER: 08 60-7 S.M. REF.: 8.5 ENGINE: EPA07 Series 60 DATE: November 2008 SUBJECT: EGR RATE MEASUREMENT SYSTEM PUBLICATION: DDC-SVC-MAN-0005 EGR Rate Measurement System has new information added. EGR
More informationEGR Actuator May Description and Operation of the DD13 Exhaust Gas Recirculation Valve Actuator
5 17-13 1 5 17-13 SUBJECT DATE EGR Actuator May 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Description and Operation of the DD13 Exhaust Gas Recirculation
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: February 2009
NUMBER: 2 5 09 S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: February 2009 SUBJECT: VALVE LIFT SPECIFICATIONS ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change
More informationPublication Number / Title Platform Section Title Change. Removal of DD15 and DD16 Delphi Exhaust Gas Recirculation Valve Actuator
7 02-15 1 7 02-15 SUBJECT DD15 and DD16 Delphi Exhaust Gas Recirculation Valve Actuator and DD15 and DD16 Sonceboz Exhaust Gas Recirculation Valve Actuator DATE July 2015 Additions, Revisions, or Updates
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA10 DD Platform DATE: August 2010
NUMBER: 815 10 S.M. REF.: Listed in Table ENGINE: EPA10 DD Platform DATE: August 2010 SUBJECT: SPN 3226 FMI 13 SCR OUTLET NOX SENSOR SIGNAL NOT AVAILABLE ADDITIONS, REVISIONS, OR UPDATES Publication Number
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: May 2013 SUBJECT: SPN 2631/FMI 2 ADDITIONS, REVISIONS, OR UPDATES
NUMBER: 5 26 13 S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: May 2013 SUBJECT: SPN 2631/FMI 2 ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change DDC-SVC-MAN-0010
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: April 2009
NUMBER: 4 11 09 S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: April 2009 SUBJECT: SPN 2631 ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page Number(s) DDC-SVC-MAN-0010
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: August 2013 SUBJECT: VALVE LASH ADJUSTMENTS ADDITIONS, REVISIONS, OR UPDATES
NUMBER: 8 34 13 S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: August 2013 SUBJECT: VALVE LASH ADJUSTMENTS ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change DDC-SVC-MAN-0005
More informationSPN 1176/FMI 3 SPN 1176/FMI 4
NUMBER: 8 01 13 S.M. REF.: Listed in Table ENGINE: EPA07 MBE 900 DATE: August 2013 SUBJECT: SPN 1176/FMI 3, 4 ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change DDC-SVC-MAN-0015
More informationAdditions, Revisions, or Updates
11 01-14 1 11 01-14 SUBJECT DATE DD15 and DD16 Cylinder Head November 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0081 DDC-SVC-MAN-0181 DDC-SVC-MAN-S181
More informationGHG14 DD15 Asymmetrical Turbocharger May Removal of the GHG14 DD15 Asymmetrical Turbocharger
5 31-13 1 5 31-13 SUBJECT DATE GHG14 DD15 Asymmetrical Turbocharger May 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the GHG14 DD15 Asymmetrical
More informationEPA10 DOC Inlet Pressure Sensor November Removal of the EPA10 Diesel Oxidation Catalyst Inlet Pressure Sensor. without Sensor Box
11 10-14 1 11 10-14 SUBJECT DATE EPA10 DOC November 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the EPA10 DDC-SVC-MAN-0083 EPA10 DD Platform
More informationHigh pressure fuel line and transfer tube removal and installation procedures have been updated.
NUMBER: 08 MBE 4000-3 S.M. REF.: 2.3 ENGINE: EPA04 MBE 4000 DATE: July 2008 SUBJECT: HIGH PRESSURE FUEL LINE AND TRANSFER TUBE PUBLICATION:DDC-SVC-MAN-0023 High pressure fuel line and transfer tube removal
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: October 2010
NUMBER:10 02 10 S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: October 2010 SUBJECT: DOUBLEHYSTERESISTEST ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page
More informationRemoval and Installation of the DD15 and DD16 Cylinder Head April Removal of the DD15 and DD16 Cylinder Head
4 102-12 1 4 102-12 SUBJECT DATE Removal and Installation of the DD15 and DD16 Cylinder Head April 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0081
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA04 MBE 4000 DATE: September 2009
NUMBER: 9 1 09 S.M. REF.: Listed in Table ENGINE: EPA04 MBE 4000 DATE: September 2009 SUBJECT: ENGINE OIL AND FILTER CHANGING ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title
More informationHydrocarbon Fuel Doser Injector Valve Fuel Supply Line December Publication Number / Title Platform Section Title Change
1 SUBJECT DATE Hydrocarbon Fuel Doser Injector Valve Fuel Supply Line December 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Hydrocarbon
More informationAdditions, Revisions, or Updates
1 8 04-12 SUBJECT DATE SPNs 4354/FMI 5, 4355/FMI 5, 4356/FMI 5, 4357/FMI 5 August 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 4354/FMI 5 DDC-SVC-MAN-0084
More informationRemoval and Installation of the Camshaft Housing Assembly February Removal of the Camshaft Housing Assembly
1 SUBJECT DATE Removal and Installation of the Camshaft Housing Assembly February 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Camshaft
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: September 2009
NUMBER: 9 3 09 S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: September 2009 SUBJECT: TURBOCHARGER WASTEGATE ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page
More informationAdditions, Revisions, or Updates
1 SUBJECT DATE Camshaft Housing Assembly March 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Camshaft Housing DDC-SVC-MAN-0081 DD Platform
More informationAdditions, Revisions, or Updates
1 2 07-13 SUBJECT DATE Removal and Installation of the Camshaft Housing February 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0081 EPA07/10/
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: June 2012 SUBJECT: E3 FUEL INJECTOR TUBE ADDITIONS, REVISIONS, OR UPDATES
NUMBER: 6 25 12 S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: June 2012 SUBJECT: E3 FUEL INJECTOR TUBE ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change E3 Fuel
More informationEGR Actuator Slow Learn April Installation of the DD13 Exhaust Gas Recirculation Valve Actuator Pull Rod
1 4 07-13 SUBJECT DATE EGR Actuator Slow Learn April 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0083 Installation of the DD13 Exhaust Gas
More informationExhaust and Exhaust Gas Recirculation September Testing of the DD13. Exhaust Gas Recirculation Cooler Water Manifold Assembly - In Chassis
1 09 04-16 SUBJECT DATE Exhaust and Exhaust Gas Recirculation September 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Testing of the DD13 DDC-SVC-MAN-0190
More informationAdditions, Revisions, or Updates
03 06-18 1 03 06-18 SUBJECT DATE Flushing the Engine Lubrication System March 2018 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change EPA07/ DDC-SVC-MAN-0081 EPA10/
More informationOil Pan July DDC-SVC-MAN-0081 DD Platform Installation of the Oil Pan Added graphics, additional torque specs.
7 17-13 1 7 17-13 SUBJECT DATE Oil Pan July 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0081 DD Platform Installation of the Oil Pan Added
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07/10 DD Platform DATE: September 2010
NUMBER: 9 09 10 S.M. REF.: Listed in Table ENGINE: EPA07/10 DD Platform DATE: September 2010 SUBJECT: INSTALLATION OF THE CAMSHAFT AND ROCKER SHAFT/ENGINE BRAKE ASSEMBLY ADDITIONS, REVISIONS, OR UPDATES
More informationExhaust Gas Recirculation Crossover Pipe December Description and Operation of the EGR Crossover Pipe (Cast)
1 12 12-18 SUBJECT DATE Exhaust Gas Recirculation Crossover Pipe December 2018 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Description and Operation of the
More informationAdditions, Revisions, or Updates
1 8 05-12 SUBJECT DATE SPN 4354/FMI 5, 4356/FMI 5, 4355/FMI 5, 4357/FMI 5 August 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 4354/FMI 5 DDC-SVC-MAN-0084
More informationAftertreatment System December Removal of the 1-BOX from the Vehicle. Installation of the 1- BOX to the Vehicle
12 13-18 1 12 13-18 SUBJECT DATE Aftertreatment System December 2018 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the 1-BOX from the Vehicle Installation
More information18SP653 EPA04 and EPA98 MBE 4000 High Pressure Fuel Line and Transfer Tube Installation
18SP653 EPA04 and EPA98 MBE 4000 High Pressure Fuel Line and Transfer Tube Installation KIT DESCRIPTION A service kit (P/N: A4600700135) is now available to install EPA07 high pressure fuel injector lines
More informationInstallation of the Fuel Rail -Three-Filter System January Publication Number / Title Platform Section Title Change
1 1 20-13 SUBJECT DATE Installation of the Fuel Rail -Three-Filter System January 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Installation of the Fuel
More informationRemoval and Installation of the Fuel Injector Cup February Removal of the Fuel Injector Cup Three-Filter System and Two-Filter System
1 2 25-14 SUBJECT DATE Removal and Installation of the Fuel Injector Cup February 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Fuel Injector
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: DD Platform DATE: May 2010
NUMBER: 5 04 10 S.M. REF.: Listed in Table ENGINE: DD Platform DATE: May 2010 SUBJECT: FUEL SYSTEM PRIMING USING ESOC 350 FUEL PRIMING PUMP ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform
More informationAdditions, Revisions, or Updates
1 3 06-13 SUBJECT DATE Potential Fuel Leak Points - Two-Filter Fuel System DD Platform March 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Potential Fuel
More informationRemoval of the Needle, Amplifier, and Pressure Limiting Valve Return Lines Three-Filter System
1 5 02-13 SUBJECT Needle, Amplifier, and Pressure Limiting Valve Return Lines Three- Filter System, Fuel Rail - Three-Filter System DATE February 2013 Additions, Revisions, or Updates Publication Number
More information18SP589* Series 60 Right Side EGR Bolt-Together System with Hydraulic Actuator Valve
18SP589* Series 60 Right Side EGR Bolt-Together System with Hydraulic Actuator Valve *Revision: 1/6/05 Introduction There are two new kits for different orientations of the hot pipe assemblies with a hydraulic
More informationAdditions, Revisions, or Updates
1 9 04-11 SUBJECT DATE SPN 3250 / FMI 16 DOC Outlet Temperature High August 2011 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 EPA07 DD13/DD15
More informationAdditions, Revisions, or Updates
1 2 22-14 SUBJECT DATE SPN 4334/FMI 7 (ACM) (EPA10) February 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform - EPA10- ACM SPN
More informationNUMBER: S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: July 2009
NUMBER: 7 10 09 S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: July 2009 SUBJECT: CAMSHAFT AND ROCKER SHAFT ASSEMBLIES ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change
More informationNUMBER: S.M. REF.: Listed in Table 1 ENGINE: 60 DATE: July 2007 SUBJECT: SERVICE MANUAL REVISIONS PUBLICATION: 6SE2007 DETAILS AND REASON
NUMBER:07 60 4 S.M. REF.: Listed in Table 1 ENGINE: 60 DATE: July 2007 SUBJECT: SERVICE MANUAL REVISIONS PUBLICATION: 6SE2007 DETAILS AND REASON The EPA07 Series 60 Service Manual has been revised. Procedures,
More informationAdditions, Revisions, or Updates
1 3 03-15 SUBJECT DATE Contaminated Fluids March 2015 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform Fuel in Oil This is a new section.
More informationFuel Injection System Low Pressure Leak Test Two-Filter Fuel System. Potential Fuel Leak Points Two-Filter. System
10 67-12 1 10 67-12 SUBJECT Fuel Injection System Low Pressure Leak Test, Potential Fuel Leak Points, Alternative Contrast Spray Method for Determining a Leak Path, Alternative Fuel Dye Method for Determining
More informationAdditions, Revisions, or Updates
1 02 06-16 SUBJECT DATE Fuel Rail - Three-Filter System February 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0082 DD Platform - All Years
More informationInstallation of the DD13,DD15, and DD16 Cylinder Head February Installation of the DD13 Cylinder Head
5 02-12Rev 1 5 02-12Rev SUBJECT DATE Installation of the DD13,DD15, and DD16 Cylinder Head February 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Installation
More informationNUMBER: 08 FSTG 12 REV S.M. REF.: Listed in Table ENGINE: EPA07 DD15 DATE: February 2009
NUMBER: 08 FSTG 12 REV S.M. REF.: Listed in Table ENGINE: EPA07 DD15 DATE: February 2009 SUBJECT: ISB (IDLE SPEED BALANCE) VALUES ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title
More informationNotice Added to Sections Listed Below February Removal of the Bypass Valve. Removal of the Pressure Relief Valve
2 15-12 1 2 15-12 SUBJECT DATE Notice Added to Sections Listed Below February 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0082 Removal of
More informationCylinder Liner January Removal of the Cylinder Liner. Cleaning of the Cylinder Liner. Inspection of the Cylinder Liner
01 18-16 1 01 18-16 SUBJECT DATE Cylinder Liner January 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Cylinder Liner Added information to
More informationNUMBER: 08 DDEC VI 16 S.M. REF.: listed in Table 1 ENGINE: DD15 DATE: April 2008 SUBJECT: SPN 1636 AND SPN 2630 PUBLICATION: DDC-SVC-MAN-0029
NUMBER: 08 DDEC VI 16 S.M. REF.: listed in Table 1 ENGINE: DD15 DATE: April 2008 SUBJECT: SPN 1636 AND SPN 2630 PUBLICATION: DDC-SVC-MAN-0029 The procedure and direction for SPN 1636 have changed. SPN
More informationHow to Replace the Lubricating Oil and Oil Filter October How to Replace the Lubricating Oil and Oil Filter
10 22-16 1 10 22-16 SUBJECT DATE How to Replace the Lubricating Oil and Oil Filter October 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0080
More informationAdditions, Revisions, or Updates
1 1 38-13 SUBJECT DATE Inspection of the Main and Connecting Rod Bearings In-Chassis January 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Inspection of
More informationAdditions, Revisions, or Updates
6 22-12 1 6 22-12 SUBJECT DATE SPN 4335/FMI 1 - EPA10 June 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 EPA10 DD Platform SPN 4335/FMI
More informationNUMBER: 08 DDEC VI 10 S.M. REF.: 92 ENGINE: EPA07 Series 60 DATE: March 2008
NUMBER: 08 DDEC VI 10 S.M. REF.: 92 ENGINE: EPA07 Series 60 DATE: March 2008 SUBJECT: SPN 2659 PUBLICATION: DDC-SVC-MAN-0009 (6SE567) Section SPN 2659/FMI 0, refer to section 92.1 SPN 2659/FMI 17, refer
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: February 2011
NUMBER: 2 15 11 S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: February 2011 SUBJECT: FAULTY FUEL INJECTOR ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page
More informationMBE 900 and MBE 4000 EGR Cooler Leak Tester
TO: FROM: SUBJECT: Service Locations Technical Support Development MBE 900 and MBE 4000 EGR Cooler Leak Tester No.: 06 TL 03rev September 20, 2006 ISSUE Detroit Diesel has released an EGR cooler test kit
More informationHigh Pressure Fuel Rail Feed Lines September Platform Section Title Change
9 10-14 1 9 10-14 SUBJECT DATE High Pressure Fuel Rail Feed Lines September 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0082 DDC-SVC-MAN-0182
More informationNUMBER: S.M. REF.: Refer to 2.5 ENGINE: 60 DATE: January 2007
NUMBER: 1 60 07 S.M. REF.: Refer to 2.5 ENGINE: 60 DATE: January 2007 SUBJECT: N3 ELECTRONIC INJECTOR PUBLICATION: 6SE483 The Series 60 Service Manual has been revised. Engine models built from December
More informationFuel Filter Maintenance Intervals July EPA10/GHG14 DD Series Preventive Maintenance Tables
1 7 14-13 SUBJECT DATE Fuel Filter Maintenance Intervals July 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0080 EPA10/ GHG14 DD Platform EPA10/GHG14
More information18SP596 Series 60 Right-Side EGR Bolt-Together System to a Spherical Joint Tube-and-Shell Cooler with Hydraulic Actuator Valve
18SP596 Series 60 Right-Side EGR Bolt-Together System to a Spherical Joint Tube-and-Shell Cooler with Hydraulic Actuator Valve Introduction There are two new kits for different orientations of the hot
More informationEngine Replacement Procedures September Removal of the Complete Powertrain Assembly. Replacement Long Block Engine Preparation
9 05-15 1 9 05-15 SUBJECT DATE Engine Replacement Procedures September 2015 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Complete Powertrain
More informationPiston and Connecting Rod Assembly August Removal of the Piston and Connecting Rod Assembly
1 8 17-13 SUBJECT DATE Piston and Connecting Rod Assembly August 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Piston DDC-SVC-MAN-0081 DD
More informationAdditions, Revisions, or Updates
4 68-12 1 4 68-12 SUBJECT DATE SPN 5018/FMI 18 - GHG14 September 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform SPN 5018/FMI
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: DD15 DATE: February 2009
NUMBER: 2 10-09 S.M. REF.: Listed in Table ENGINE: DD15 DATE: February 2009 SUBJECT: CAMSHAFT TIMING ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Page Number(s) DDC-SVC-MAN-0002
More informationHard Start/No Start - Two-Filter Fuel System (This Test Must Be Done First) Test-A - Two-Filter Fuel System. Test-C - Two-Filter Fuel System
1 SUBJECT DATE Symptom Diagnostics - Hard Start/No Start - Two-Filter Fuel System June 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Hard Start/No Start
More informationAdditions, Revisions, or Updates
1 5 33-13 SUBJECT Removal and Installation of the High Pressure Fuel Pump -Three- Filter System DATE May 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal
More informationAdditions, Revisions, or Updates
2 27-14 1 2 27-14 SUBJECT DATE SPN 4335/FMI 7 - EPA10 February 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform SPN 4335/FMI 7
More informationPerform the following procedures for removal and installation of the protective sleeve.
MBE 4000 SERVICE MANUAL 2.6 PROTECTIVE SLEEVE Perform the following procedures for removal and installation of the protective sleeve. 2.6.1 Protective Sleeve Removal Remove the protective sleeve as follows:
More information18SP631 MBE 4000 Oil Gallery Threaded Plug Installation
18SP631 MBE 4000 Oil Gallery Threaded Plug Installation KIT DESCRIPTION A new service kit (P/N: 23536501) is now available to install two threaded plugs in place of cup plugs in the rear oil gallery on
More informationPublication Number / Title Platform Section Title Change. Description and Operation of the Diesel Particulate Filter End Cap
04 04-18 1 04 04-18 SUBJECT GHG17 DD8 - Aftertreatment Systems - Diesel Particulate Filter End Cap DATE April 2018 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change
More informationPiston and Connecting Rod Assembly January Removal of the Piston and Connecting Rod Assembly
1 18-13 1 1 18-13 SUBJECT DATE Piston and Connecting Rod Assembly January 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Piston and Connecting
More information18SP660Rev2 EPA04 and EPA07 MBE 4000 Steel Low Pressure Fuel Line Kits (P/N: A and A )
18SP660Rev2 EPA04 and EPA07 MBE 4000 Steel Low Pressure Fuel Line Kits (P/N: A4600702932 and A4600703032) KIT DESCRIPTION New service kits (P/N: A4600702932 and A4600703032) contain a steel low pressure
More informationPublication Number / Title Platform Section Title Change. Removal of the High Pressure Fuel Pump Drive Gear - Three-Filter System
5 34-13 1 5 34-13 SUBJECT Removal and Installation of the High Pressure Fuel Pump Drive Gear - Three-Filter System DATE June 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section
More informationAdditions, Revisions, or Updates
1 02 23-16 SUBJECT DATE Diesel Oxidation Catalyst Air Cleaning February 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DDC-SVC-MAN-0191
More information18SP680Rev3 EPA04 MBE 4000 Car Hauler Low Pressure Fuel Lines
8SP680Rev3 EPA04 MBE 4000 Car Hauler Low Pressure Fuel Lines KIT DESCRIPTION These service kits include all necessary parts to replace the low pressure fuel lines between the fuel filter housing and fuel
More information18SP597 Series 60 Right-Side EGR Bolt-Together System to a Spherical Joint Tube-and-Shell Cooler with Pneumatic Actuator Valve
18SP597 Series 60 Right-Side EGR Bolt-Together System to a Spherical Joint Tube-and-Shell Cooler with Pneumatic Actuator Valve Introduction There are two new kits for different orientations of the hot
More informationAdditions, Revisions, or Updates
1 01 06-15 SUBJECT DATE SPN 3251 (ACM) (EPA10) and (GHG14) January 2015 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 3251/FMI 0 - GHG14 DDC-SVC-MAN-0084
More information18SP712 EPA07 DD15/16 Three-Filter Fuel System to Two-Filter KM59 GEN1 Fuel System Conversion Service Kit (P/N: A )
18SP712 EPA07 DD15/16 Three-Filter Fuel System to Two-Filter KM59 GEN1 Fuel System Conversion Service Kit (P/N: A4710901055) KIT DESCRIPTION This service kit includes all necessary parts to convert the
More informationBelt Drive January Platform Section Title Change. Description and Operation of the Belt Drive Tensioner System. Removal of the Belt Tensioner
1 01 06-18 SUBJECT DATE Belt Drive January 2018 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0190 DDC-SVC-MAN-0081 GHG17 DD Heavy Duty DD Heavy
More informationAdditions, Revisions, or Updates
1 8 08-14 SUBJECT DATE SPN 4364 (ACM) (EPA10) August 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform SPN 4364/FMI 1 - EPA10 SPN
More informationAdditions, Revisions, or Updates
1 5 25-13 SUBJECT DATE SPN 2791/FMI 7 ALL YEARS May 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform SPN 2791/FMI 7 Deleted part
More informationThe EPA07 Series 60 Workshop Manual has been revised. Listed in Table 1 are the revisions.
NUMBER: 08 60-6 S.M. REF.: 2.3.1 and 2.3.2 ENGINE: EPA07 Series 60 DATE: September 2008 SUBJECT: E3 INJECTOR TUBE PUBLICATION: DDC-SVC-MAN-0005 The EPA07 Series 60 Workshop Manual has been revised. Listed
More information2003 F-Super Duty /Excursion Workshop Manual
Page 1 of 7 SECTION 303-04F: Fuel Charging and Controls Turbocharger, 6.0L Diesel 2003 F-Super Duty 250-550/Excursion Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005 Turbocharger
More informationREMOVAL AND INSTALLATION
303-08-1 Engine Emission Control 303-08-1 REMOVAL AND INSTALLATION Exhaust Gas Recirculation (EGR) Cooler 6.4L Diesel, Vertical Cooler Item Part Number Description 1 Fuel cooler tube 2 W701317 Power steering
More information18SP720 EPA10 DD15/16 Three-Filter ESOC Fuel System to Two-Filter KM59 GEN1 Fuel System Conversion Service Kit (P/N: A )
18SP720 EPA10 DD15/16 Three-Filter ESOC Fuel System to Two-Filter KM59 GEN1 Fuel System Conversion Service Kit (P/N: A4710901455) KIT DESCRIPTION This service kit includes all necessary parts to convert
More informationSECTION D Fuel Charging and Controls Turbocharger
303-04D-i Fuel Charging and Controls Turbocharger 303-04D-i SECTION 303-04D Fuel Charging and Controls Turbocharger CONTENTS PAGE Turbocharger Body On... 303-04D-2 303-04D-2 Fuel Charging and Controls
More informationPublication Number / Title Platform Section Title Change SPN 5246/FMI 0- EPA10 SPN 5246/FMI 15 - EPA10 SPN 5246/FMI 16 - EPA10 SPN 5246/FMI 0 - GHG14
1 3 04-14 SUBJECT SPN 5246/FMI 0, 15, 16 (ACM2)(EPA10) SPN 5246/FMI 0, 15, 16 (ACM2.1)(GHG14) DATE March 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN
More informationAdditions, Revisions, or Updates
1 3 26-15 SUBJECT DATE Main Shaft Speed Sensor March 2015 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0140 Transmission Removal of the Main Shaft
More informationThis information covers the proper replacement procedure for the EGR valve on the Volvo D16F engine.
Volvo Trucks North America Greensboro, NC USA EGR Valve, Replacement DService Bulletin Trucks Date Group No. Page 11.2006 254 24 1(17) EGR Valve Replacement D16F W2005772 This information covers the proper
More informationAdditions, Revisions, or Updates
1 12 02-12 SUBJECT DATE Test E - Three-Filter Fuel System December 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform Test E - Three-Filter
More informationFIS Low Pressure Leak Test March Publication Number / Title Platform Section Title Change. FIS Low Pressure Leak Test- Three-Filter Fuel System
1 3 02-13 SUBJECT DATE FIS Low Pressure Leak Test March 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform FIS Low Pressure Leak
More information