FRAMES: ENGINE LOCATION:
|
|
- Scarlett Jefferson
- 5 years ago
- Views:
Transcription
1 All Safety Equipment is Subject to Track Inspection and Approval, applies to all times car is on the track including packing. Snell-Rated Helmet in Good Condition, SFI-Approved full fire suit, fire retardant gloves, shoes and neck brace (or head and neck restraint system) required. Minimum three inch wide SFI-Approved Five Point Safety Belt assembly required (2 inch with head and neck restraint system) and must mount securely to main roll cage. Fire-resistant Roll Bar Padding required on any part of Roll Cage Driver may contact with while buckled in. Driver-side Window Net required, Minimum 16 inch by 20 inch ribbon or mesh style, and must be mounted to roll cage so latch is at Top and Front of driver s window opening. Recommend: Safety Belts to be no more than two years old, fire retardant head sock and underwear and collapsible steering shaft. FRAMES: 105 minimum wheelbase 110 maximum wheelbase 1 tolerance forward or backward. Front Clips may be of OEM Stock Clip design or Fabricated 2 x3 Clip built to GM Camaro Specifications. If running 2 x3 fabricated front clip you must add 25 lbs. of weight in front of most forward spark plug hole. Left or right side of car. Front Clips must be of A-Arm configuration, both upper and lower. Front frame extensions cannot be any larger than 2 inch wide x 3 inch height by.083 inch thickness steel magnetic tubing welded at a point of 2 inches in front of steering gear box, must angle down at a maximum angle of 18 degrees. Stock front clipped cars center main frame section beginning at main cage front mounting points may be constructed with minimum of 2 inch x 2 inch x.095 square or minimum 1.75 inch round OD x.095 steel magnetic tubing. Rear of Main Frame may be wider or narrower than front of frame. X-Bracing is allowed. Front GM Type or Ford Front Fabricated Clip Specifications, Subject to I-37 Track Official Inspection and Approval ENGINE LOCATION: Minimum Height 12 inches from ground to center of crankshaft. Setback 1 ½ inch from center of left upper ball joint to most forward spark plug hole. ROLL CAGE:
2 Must be of four post design and consist of continuous hoops with a minimum roll cage piping size of 1.5 inch OD x.095 thick magnetic steel tubing. Main cage rear hoop must have a minimum of one horizontal bar and one diagonal bar from top of hoop to bottom of down post. Main roll cage hoop and halo must be a minimum of 1 inch above drivers head with helmet on and driver buckled in car. Main cage front uprights must tie together with a minimum of one horizontal bar. Front left and right kickers required from main cage to in front of engine. Rear left and right kickers required from main cage to rear frame section. Front and rear loops allowed. DOOR BARS: Minimum of three driver s doors bars minimum of 1.5 inch OD x.095 magnetic steel tubing parallel to frame and perpendicular to driver, must have a minimum of two uprights intertwined into horizontal doors bars from frame to top door bar to strengthen door bar system. Foot protection required. Steel door plate of 18 gauge or inch minimum thickness must be securely welded to driver side door bars and cover area from top of door bars to frame and from rear down post to 5 inches in front of seat, may be welded into door bar system design. Minimum of one diagonal bar or X-Brace must tie right front upright to rear hoop down bar on passenger side. BODY: Any Steel, Aluminum or Fiberglass Body allowed. MD3 Dirt Late Model Body recommended. Rear Spoiler not to exceed 10 inches in material height, may be Lexan. NO Nerf Bars Allowed on the outside of the body. Cars must be keep neat appearance; any loose or flapping body panels may cause car to receive mechanical black flag and will not be allowed to compete until repair is made. DRIVER COMPARTMENT: Minimum three windshield bars in front of driver. Lexan or aluminum cowl panel in front of driver allowed, but can be no wider than cockpit and no farther back than steering wheel. Driver must be sealed off from track, driveline, engine, fuel cell, suspension components, battery, coolers and fuel lines. Aluminum high back racing seats required, must be bolted in with a minimum
3 of inch bolts. NO rear view mirrors. NO driver-adjustable devices allowed while car is in competition except brake adjuster and right front brake shut-off. SUSPENSION: Front Steel aftermarket Spindles and Wide Five Hubs allowed, Aluminum Spindles not allowed. Tubular upper control arms allowed and can be adjustable. Lower control arms may be aftermarket steel stock or stock mount type, may be heim end. Weight jacks allowed, cannot be adjusted from inside driver s compartment. Coilovers allowed. Sway bar allowed but cannot be adjusted inside driver s compartment. Rear Steel Coil Springs, Coilovers OK, Steel or Composite Leaf Springs OK. Weight Jacks cannot be adjusted from inside driver s compartment. Configuration may consist of a Three Link, OEM Chevelle Type Four Point, Swing Arm or of Leaf Spring configuration including Mono Leaf/Coil Over design. NO Four Links, Z-link, or Jacob s Ladder. NO Independent Rear Suspension. NO lift, brake or rear sway bars. All suspension components may be steel or aluminum, including heims. Trailing Arms may consist of steel radius rod design, cannot be bushed, cannot extend or collapse other than by manual adjustment of heim ends. Pan Hard or J-Bars allowed, may be adjustable, J-Bar may be rubber bushed. One mechanical pull bar allowed may be of a single spring or biscuit design. One single steel or aluminum bodied shock may be mounted above pull bar from rear end and must mount forward of rear end. Shocks: Any Steel or aluminum bodied shock allowed. NO adjustable shocks, NO remote reservoir shocks, NO air shocks, NO Schrader or Bladder type shocks. STEERING: OEM type Steel Steering Component Configuration or Rack and Pinion. Note: Rack and Pinion must bolt 10 lbs of ballast weight in place of gear box. Steering gear box must bolt in stock location on OEM clip or in OEM position on any fabricated clip.quick Steer Ok. Aftermarket Center Links and Tie Rods steel or aluminum allowed including Tubes and Heim
4 Ends. Quick release Steering Wheel required. BRAKES: Aftermarket brake systems allowed including brake pedals, master cylinders, calipers and pads. Calipers may be steel or aluminum and be of single or dual piston design. Brake bias adjuster allowed and may be accessible in driver s compartment. NO Carbon Fiber Brake parts. Cooling holes maybe drilled in rotors. Right front brake shut off allowed and may be accessible from driver s compartment. ENGINE: Block OEM or Aftermarket Cast Iron V-8 Small Block with a Maximum of 364 CID. Block must remain as cast, absolutely no lightning of any kind to block. 604 crate Motor allowed. Must add 25 lbs of weight in front of transmission NO V6 or Big Block Engines. Lifter valleys may be deburred, valley vents and screens may be installed. No enlarging or bushing of lifter bores. Wet Sump Oiling only NO Dry Sump or any type External Oil Systems allowed. Aftermarket Steel Oil Pan allowed, with mandatory 1 inspection hole to allow inspection of crankcase area. Windage Tray OK Aftermarket Balancer OK Aftermarket Engine Bolts allowed. Water Pump must be belt driven, can be cast iron or aluminum. Crankshaft Any Steel or Cast Iron Crankshaft allowed as follows: 2.0 journal cranks are allowed. NO Honda journal cranks. Minimum Weight of 48 lbs. Knife edging, contouring or stream lining is not allowed. All Crankshafts must be within.060 of OEM specifications on rod and main bearing journals. NO small journal Crankshafts allowed. Pistons/Rods Any flat top or dished pistons allowed. Must have Steel wrist pins. NO part of piston may rise above block deck. Connecting Rods must be Steel, can be of cap screw or bolt design. Cylinder Heads/Intake Any Cast Iron 23 degree Head on GM, 20 degree on Ford. Ford N head is allowed Any CC allowed. Intake and Exhaust Ports must remain as cast, No porting/polishing. Gasket Matching allowed not to extend more than 3/8 of an inch into port.
5 Stamped Steel, Roller Tipped or Full Roller Rockers allowed, any ratio. NO Shaft Type Rocker Arm assemblies allowed. Stud Girdles allowed Valves must be steel, No Titanium Valves allowed. Timing Chain and Gears, may be of Double Roller design, NO Belt or Gear Drives. Any Aluminum Intake. Camshaft and Lifters Any flat tappet Cam with OEM stock diameter Lifters. NO Roller Cams or Roller Lifters allowed. Mushroom or Radius Lifters not allowed. Push Rods must be steel. Rev Kits allowed. CARBURETOR: Single (1) Maximum 750 CFM Vacuum or Mechanical Secondary or below allowed. o Aftermarket billet aluminum metering blocks OK. o May be modified to run Methanol or E85. o Throttle blades or throttle shaft must retain stock thickness and is subject to Go/No-Go gauge inspection o Additional holes or passages are not allowed. Screws or linkages on vacuum secondary carburetors may mechanically force open secondaries. Carburetors must have two (2) throttle return springs. Carburetor Spacer not to exceed inch including gaskets. NO Aerosol type Carburetors allowed. NO type of forced air induction allowed. NO cool cans allowed. FUEL/FUEL CELL: Racing Fuel, Methanol or E85. Smell enhancing additives OK. All cars running methanol must have letter A on drivers side sail panel. Minimum of 4 in height. This is MANDATORY. NO performance enhancing additives or pressurized fuel systems allowed. Racing Fuel Cell Required. Maximum 32 gallon capacity and must be enclosed in a 20 gauge steel container. Must mount between rear frame rails and behind rear end, bottom of cell can be no lower than center section of rear end. Must be properly supported and protected, must be minimum of 1.5 inch tubing loop to protect bottom of fuel cell. Must mount with minimum two solid steel straps surrounding entire fuel cell, 2 inches wide by inches thick.
6 Fuel Cell vents including cap vent must have check valves. Fuel Shut Off recommended. TRANSMISSION/DRIVESHAFT: Transmission Aftermarket Transmissions are allowed, Bert, Brinn and Falcon. Must have a minimum of two forward speeds, reverse and neutral. Standard production OEM 3 or 4 Speed Transmissions allowed. Explosion proof steel bell housing minimum 180 degrees around top of clutch and flywheel must be used with all external clutch type transmissions. Mini Clutches OK. Powerglide Transmissions with Coupler OK, must have SFI Steel Flex Plate, and SFI Steel Flexplate Shield. SFI Transmission Scatter Shield recommended. NO In and Out Boxes. DRIVESHAFT: Steel Driveshaft with minimum diameter of 2 inches. Cannot be carbon fiber, aluminum, or any other material other than steel. Must be painted white with car number in contrasting color. 360 degree front drive shaft loop required within 6 inches of front U-joint, minimum.025 inch x 2 inch steel. EXHAUST: Any bolt on header with no adapters. Must be of collector type only. RADIATOR/ENGINE COOLING: Radiator must be mounted in front of engine, between frame rails and have protection. Cooling fan must be water pump mounted and fan driven, NO electric cooling fans. REAR END: Quick-change Rear-Ends or 9 inch Ford Full Floaters allowed. Quick change must use 10 ring gear with aluminum or steel spool. Quick change must use minimum one inch wide spur gears and bolt on rear cover. Axle tubes may be aluminum or steel. Center Section of Ford 9 inch may be aluminum. Rear Ends must be locked. Any full or mini spool allowed. NO torque dividing differentials, scalloped ring gears, or cambered rear ends. Rear end coolers allowed. BATTERY & STARTER:
7 Battery must be securely mounted to chassis, between frame rails with positive terminal covered. Starter must be in working order and car must start under own power. Note: Car must leave staging area on demand and unaided, any car which causes a delay in starting or restarting of race due to starting issues will be put to back of that race. ELECTRICAL & IGNITION: Electrical A master battery power Kill Switch is required and should be mounted within easy reach of driver and be accessible from outside of car by track personnel, must be labeled Off/On. When switch is in Off position all electrical power to car must be disconnected. Alternator is optional, switch must also disconnect power to alternator if equipped. Ignition switch must be mounted within reach of driver and outside of car by track personnel and must be clearly labeled. Ignition OEM Stock HEI or MSD Ignition Systems allowed. External Ignition Boxes Ok, (6A, 6AL & 6ALN) only one box per car, out of reach of driver. NO Magneto ignitions allowed. Absolutely No Electronic Traction Control of any kind, end result will be DQ, forfeit of all winnings/points and an automatic 1 year suspension. WHEELS & TIRES: Steel Racing type wheels only, Aluminum wheels not allowed. Bead Locks OK. Maximum Wheel width of 10 inches. Any 11 inch Tire allowed any compound. Wide Five hubs and wheels allowed. Air pressure relief valves not allowed. Chemical softening or treating of any kind not allowed. Tires may be grinded, sipped or grooved. WEIGHT: Minimum Weight 2800 lbs. Ballast Weight Must be painted white with car number, must be securely fastened with a minimum of 2 ½ inch. steel bolts. SCORING: Car numbers must be a minimum of 24 inches in height and 4 inches in width, and be clearly visible from scoring tower on both sides and top of car. 6 inch numbers on front and rear of car for line up procedures.
8 If you have any questions or require any clarifications please do not hesitate to ask. Steven Whiteaker Jr ALL cars are subject to track inspection and approval before entering into competition, and may be subject for re-inspections. Any car which is determined as unsafe will not be allowed to compete until safety issue is corrected and car is declared safe for competition. STS reserves the right to clarify or amend these rules as deemed necessary.
Econo-Mod Rules. *Transponders & Raceceivers mandatory*
Econo-Mod Rules Top 3 from each heat must scale. Top 5 from each feature must scale & go immediately to tech. Failure to do so will result in a disqualification. *Transponders & Raceceivers mandatory*
More information2012 Street Stock Rules
Rules & Regulations Updated 11/26/11 CHASSIS: 1. Cars must be 1960 or newer, stock passenger type cars. 2. No Commercial vehicles, convertibles, sports cars or Novas allowed. No leaf spring cars. 3. Frame
More information2017 Sportmod (B Mod) Rules
2017 Sportmod (B Mod) Rules FRAMES 1. 1964 or newer OEM perimeter American rear-wheeled passenger car frame only. No sports car frame. No convertible or station wagon. No stub cars 2. Frame must be full
More informationSUPER 4-CYLINDER RULES MODELS
SOUTHERN OREGON SPEEDWAY 2177 South Pacific Highway Medford, OR 97501 541-282-8066 / 1-800-963-3367 Fax: 541-774-3627 / Website: www.sospeedway.com SUPER 4-CYLINDER RULES 2009 1. MODELS A. Any front engine,
More informationSANDIA SPEEDWAY 2018 STREET STOCK DIVISION RULES
SANDIA SPEEDWAY 2018 STREET STOCK DIVISION RULES DRIVER: The minimum age for a driver is fourteen (14), unless approved by two of the following three: race director, tech inspector or promoter. All required
More information2015 Super Stock verses Street Stock. Rules UPATES 2/12/2015
2015 Super Stock verses Street Stock Rules UPATES 2/12/2015 1. All racecars must display Super Stock or Street Stock at which it will compete on left side windshield post. Must be two (2) inches tall.
More information2018 Senoia Raceway Rulebook Late Model Sportsman
(Formerly B Cadet) All drivers must adhere to the general rules, in addition to the division specific rules set forth below. BODY 1. Stock appearing body may be aluminum or steel. 2. Rear of body may be
More informationARIZONA SUPER STOCK Super Stock Rules and Regulations
ARIZONA SUPER STOCK 2014 Super Stock Rules and Regulations If the rules don t say you can, assume you cannot. The rules are written as a guideline. If you are unsure about something, ask an official. The
More information2019 Super Street Class Rules. All drivers are required to have their own Raceivers for one-way communication with race director official.
2019 Super Street Class Rules All drivers are required to have their own Raceivers for one-way communication with race director official. Top 3 feature finishers will be required to go to tech area after
More informationPLEASE BE SURE YOU HAVE READ AND UNDERSTAND THE GENERAL RULES, SAFETY RULES AND DRIVER SAFETY EQUIPMENT BEFORE CONTINUING.
2017 SPORTSMAN RULES Any rule changes made in 2017 are highlighted in RED. *Speedway Officials shall be empowered to permit minor deviations from any of the specifications herein or impose any further
More information2018 PURE STOCK RULES
2018 PURE STOCK RULES PROTEST: 1. Engine Top $300 bottom $300 2. 602 Crate Engine $350 Top $400 Bottom 3. $100 per shock Claim Rule top three only 4. Tire Protest $100 (one tire) top three only 5. CRATE
More informationWILD BILL S RACEWAY MODIFIED RULES 2010
WILD BILL S RACEWAY MODIFIED RULES 2010 1. SAFETY: Snell 2000 helmet required and must be worn at all times car is on track (SA 2005 recommended). Roll bar padding (fire retardant recommended) driver compartment.
More information2017 Thunder Series 602 Thunder Series Rules
2017 Thunder Series 602 Thunder Series Rules Chassis: 1. Must follow FASTRAK rules. 2. Chassis must be built prior to 2014 Body: 1. Must follow FASTRAK body rules 2. 8 spoiler permitted 3. No 12 side braces
More informationCHARGER 2017 RULES & REGULATIONS Revised 1/22/17
CHARGER 2017 RULES & REGULATIONS Revised 1/22/17 IMPORTANT NOTE: Applications for NASCAR License may be obtained from the Pit Steward at the sign -in-window or at the speedway office during regular business
More informationSportsman Truck Rules for Updated: 12/16/2017 Must be at least 14 years of age.
Sportsman Truck Rules for 2018 Updated: 12/16/2017 Must be at least 14 years of age. SNELL-RATED SA2005, SA2010, OR SA2015 HELMET REQUIRED. SFI-APPROVED FULL FIRE SUIT REQUIRED. FIRE RETARDANT GLOVES,
More information2017 PURE STOCK RULES
2017 PURE STOCK RULES PROTEST: 1. Engine Top $300 bottom $300 2. 602 Crate Engine $350 Top $400 Bottom 3. $100 per shock Claim Rule top three only 4. Tire Protest $100 (one tire) top three only ALL CARS
More informationTHIS CLASS IS TO REMAIN STOCK APPEARRING WITH ALL COMPONENTS IN STOCK LOCATION
SOUTHERN OREGON SPEEDWAY Website: www.sospeedway.com 2013 STREET STOCK RULES THIS CLASS IS TO REMAIN STOCK APPEARRING WITH ALL COMPONENTS IN STOCK LOCATION 1. MODELS: A. American sedans and hardtops. Station
More information2019 Street Stock Rules
Presented By 2019 Street Stock Rules 1) Car Body and Frame Any stock, production American-made vehicle including Camaro, Firebird and Mustang. Pickups will be allowed 1. Trunk pan may be removed for fuel
More informationNorth Central Arkansas Speedway, LLC
2018 North Central Arkansas Speedway, LLC Hobby/ Factory Stock Rules THE RULES AND/OR REGULATIONS SET FORTH HEREIN ARE DESIGNED TO PROVIDE FOR THE ORDERLY CONDUCT OF RACING EVENTS AND TO ESTABLISH MINIMUM
More informationELIGIBLE MODELS Chevy C-10 GMC 1500 Dodge Ram Ford F-150
2018 SUPER TRUCKS RULES $1000 fine for tire soaking $100 fine for antifreeze ELIGIBLE MODELS Chevy C-10 GMC 1500 Dodge Ram Ford F-150 HMS Enforcer (Harrington Spec) 2850/1265 lbs with driver 1. Minimum
More information2019 Pure Thunder Stock Class Rules. All drivers are required to have their own Raceivers for one-way communication with race director official.
2019 Pure Thunder Stock Class Rules All drivers are required to have their own Raceivers for one-way communication with race director official. Top 5 feature finishers will be required to go to tech area
More information2018 Mini Sport Rules
2018 Mini Sport Rules Mini Sport 2018 revised 12/21/2016 1. ELIGIBILITY A. Front engine, compact cars and short wheel base mini trucks with conventional cabs. B. NO Convertables, Station Wagons, supercabs,
More informationI-96 Speedway Street Stock Rules
I-96 Speedway 2019 Street Stock Rules Personal Protection Equipment It is the sole responsibility of each competitor for the effectiveness and proper installation, per the manufacturers specifications
More information2019 Road Warriors. Shock claim rule will be $50. Any driver finishing in the top 3 may claim shocks from any car finishing in the top 3.
2019 Road Warriors Protest $350 top end/ $400 bottom end any engine combination Crate engine claim rule will be $3900. Any car finishing on the lead lap may claim any engine that finishes on the lead lap.
More informationMichigan Sport Modified Rules Merritt Speedway
1 Michigan Sport Modified Rules 2017 - Merritt Speedway Merritt Speedway management is pleased to introduce the Michigan Sport Modified division in 2017! The following rules are closely mirrored to Mt.
More informationEngine option #1 Nesmith sealed 602 with 4412 Holley 500 cfm two barrel. 1" spacer.030 tolerance. Street Stock Rules
Hobby Street Stock Rules (Updated 1/1/2019) 1. All 3300 lbs 2. Remote starter button track supplied at inspection 3. No high performance parts allowed except as stated. 4. Wheel base 108. min. 5. Stock
More information2013 Senoia Raceway Rulebook
2013 Senoia Raceway Rulebook E-mail tech questions to: johnnywalls31@yahoo.com BOMBER RULES BODY 1. All bodies must be stock steel bodies. No fiberglass or aluminum body panels allowed. Fenders and quarter
More information#800 to #899 Sportsman Super Stock Truck Technical Specifications
#800 to #899 Sportsman Super Stock Truck Technical Specifications DEFINITION A two wheel drive, standard size pickup. The truck must be of stock production that has been produced in quantities of at least
More informationLIMITED LATE MODEL. A. Standard Dirt Style body required. A stock appearing nose is required.
LIMITED LATE MODEL BODY: A. Standard Dirt Style body required. A stock appearing nose is required. B. Schaeffer Oil Southern nationals Body rules apply. C. See tech inspector if you have any questions.
More informationMAHONING VALLEY SPEEDWAY 2019 LATE MODEL RULES ALL CARS MEETING THESE RULES & SPECIFICATIONS WILL BE ELIGIBLE TO RACE
MAHONING VALLEY SPEEDWAY 2019 LATE MODEL RULES ALL CARS MEETING THESE RULES & SPECIFICATIONS WILL BE ELIGIBLE TO RACE These rules are intended to be a guideline in constructing a car. If the rules do not
More informationLarry King Law Langley Speedway 2018 Modified Division Rules
Larry King Law Langley Speedway 2018 Modified Division Rules Amendments: Rules are subject to amendments at any time when ample notice has been given to enhance competition 1. ROLL CAGES A. Roll bars must
More information2019 Toccoa Raceway. Fuel: 110 or 114 NO OXYGENATED FUEL PERMITTED. Body:
2019 Toccoa Raceway Stock 4 Cylinder (Window Safety Net & Mufflers are Mandatory) ** WEIGHT MUST BE POSTED ON THE TOP LEFT CORNER OF THE DRIVERS DOOR *** NUMBER MUST BE 3 TALL & VISIBLE Fuel: 110 or 114
More information2017 SANDUSKY SPEEDWAY MODIFIED RULES
2017 SANDUSKY SPEEDWAY MODIFIED RULES Note: Sanctioning body and/or track does not express or implies any warranty of safety resulting from the publication of or compliance with these rules and/or regulations.
More information2019 Senoia Raceway Rulebook Hobby Stock
All drivers must adhere to the general rules, in addition to the division specific rules set forth below. WARNING PLEASE READ All cars with replaced frame or frame rails must first be approved by Track
More information2018 Toccoa Raceway. A. Stock for make and model (1 inch) tolerance SIDE TO SIDE.
2018 Toccoa Raceway Modified Street Rules (Window Safety Net & Mufflers are Mandatory) Frame: A. OEM Suspension in original location B. GM/ Metric Tubular Replacement permitted Johnson Chassis only. C.
More informationPROSTOCK CLASS. Infraction of rules will be decided by Race Officials. Number Plate
PROSTOCK CLASS Tech Rules: Must have race receiver and needs to work (cruiser class: both driver & passenger must be able to hear) All four brakes must lock up or won t race. You will load up and go home
More informationPure Stock Specifications
15112 National Pike, Hagerstown, MD 21740 PHONE (301) 582-0640 FAX (301) 582-3618 info@hagerstownspeedway.com Pure Stock Specifications ENGINES A.) Solid lifter cams allowed. No rollers B.) Roller Rockers
More informationBirch Run Speedway Modified Division 2018 Official Rules
Birch Run Speedway Modified Division 2018 Official Rules 1. Safety Birch Run Speedway safety rules follow standards set forth by the SFI Foundation, Inc. A. Helmet must be 2010 Snell standard or better
More information2019 PURE STOCK RULES ALL CHANGES/MODIFICATIONS TO THE 2019 PURE STOCK RULES ARE IN RED.
2019 PURE STOCK RULES ALL CHANGES/MODIFICATIONS TO THE 2019 PURE STOCK RULES ARE IN RED. DRIVERS A. Driver must be at least 14 years of age. Must have Minor release form signed by parent or guardian on
More informationLavonia Speedway 2018 Racing Season
Lavonia Speedway 2018 Racing Season Stock 4 Cylinder- (Window Safety Net & Mufflers are Mandatory) (*note 2 engine combinations*) BODY - A. Stock auto only B. May have complete aluminum body C. Inner panel
More information2018 Pure Stock Rules. The rules listed below are being enforced for all drivers of the Pure Stock class to abide
2018 Pure Stock Rules The rules listed below are being enforced for all drivers of the Pure Stock class to abide by. For questions contact the race track or technical director. Contact information is listed
More informationRULE BOOK DISCLAIMER
RULE BOOK DISCLAIMER The rules and/or regulations set forth herein are designed to provide for the orderly conduct of racing events and to establish minimum acceptable requirements for such events. These
More informationThunder Bomber 2018 GENERAL
Thunder Bomber 2018 GENERAL - Tech man has right to check this every week. 1. No nitrous or traction control. 2. After 3 times of refusing to tear down - you will be disqualified from competing in this
More information2014 DIRTcar Stock Car Rules
2014 DIRTcar Stock Car Rules TO ALL COMPETITORS/PARTICIPANTS The following are the 2014 DIRTcar Stock Car rules. All amendments supersede any previous rules regarding any technical article and/or aspect.
More information2018 Midwest Modified Rules
2018 Updates New Style Chip Box Required (CT8727) No Weight Added To Rear Axle No heavy weight axle tubes (max.250 wall) 1 of 6 1. Communications 1.1. All competitors must have a RACECEIVER 1600 in car
More informationSection 10 Mini Stocks
Section 10 Mini Stocks 10.1 DEFINITION. 10.1.1 The word stock will mean unaltered as originally factory produced and installed for make. All Cars and trucks will be stock unless otherwise specified within
More informationPURE/HOBBY/STRICTLY STOCK/CHARGER RULES
PURE/HOBBY/STRICTLY STOCK/CHARGER RULES 1. GENERAL This division is open to any North American made rear wheel drive passenger car or mid-size truck 1955 to present. Station wagons allowed! NO Jeeps, 4
More informationRACECEIVERS MANDATORY: TRANSPONDERS MANDATORY: IT IS THE DRIVERS RESPONSIBILITY TO HAVE THEM IN WORKING ORDER TO RACE AT THUNDERBIRD RACEWAY.
General Pro Street Rules 2019 It is the sole responsibility of each competitor for the effectiveness and proper installation of safety equipment per the manufacturer s specifications to be adequate for
More informationNatural Bridge Speedway Official 2016 Rules Sportsman
Natural Bridge Speedway Official 2016 Rules Sportsman www.nbspeedway.com 540-451-2943 Official 2016 Sportsman Rules Natural Bridge Speedway Page 2 Rulebook Disclaimer The rules and/or regulations set forth
More informationLarry King Law Langley Speedway 2018 Pro-Six Division Rules
Larry King Law Langley Speedway 2018 Pro-Six Division Rules Amendments: Rules are subject to amendments at any time when ample notice has been given to enhance competition 1. Chassis, Frame Rails and Roll
More information2018 TOCCOA RACEWAY. Stock 4 Cyl. (Window Safety Net & Mufflers are Mandatory)
Stock 4 Cyl (Window Safety Net & Mufflers are Mandatory) Fuel: A) 110 Track Fuel B) NO OXYGENATED FUELS C) NO E85 Body: 2018 TOCCOA RACEWAY A) Any two or four door foreign or domestic car with a 94-101.5
More informationRULE BOOK DISCLAIMER DIXIE SPECIAL EVENT PONY RULES
RULE BOOK DISCLAIMER The rules and/or regulations set forth herein are designed to provide for the orderly conduct of racing events and to establish minimum acceptable requirements for such events. These
More informationLarry King Law s Langley Speedway 2018 Super Truck Division Rules
Larry King Law s Langley Speedway 2018 Super Truck Division Rules Amendments: Rules are subject to amendments at any time when ample notice has been given to enhance competition 1. COMPETING MODELS A.
More information2018 TOCCOA RACEWAY 9: THERE WILL BE A $3800 CLAIM RULE ON A CRATE ENGINE. IF YOU CLAIM THIS ENGINE YOU ARE NOW RESPONSIBLE FOR THIS ENGINE
602 Sportsman Rules (Window safety net & mufflers are mandatory) 2018 TOCCOA RACEWAY ENGINE RULES: 1. CHEVROLET PERFORMANCE PART NUMBER 88958602/19258602 2. THE SEALED ENGINES MUST REMAIN INTACT AND NOT
More informationAll drivers must have working race radios in order to compete. Scoring Transponder is optional for 2015 but will be mandatory for 2016
Brockville Ontario Speedway 2016 BOS STREET STOCK RULES All drivers must have working race radios in order to compete. Scoring Transponder is optional for 2015 but will be mandatory for 2016 CAR ELIGIBILITY
More informationEAST ALABAMA MOTOR SPEEDWAY 2018 HOBBY TECHNICAL RULES
**Rules new for 2018 will be highlighted in BLUE. **Last updated on 12-22-17. EAST ALABAMA MOTOR SPEEDWAY This division is open to any 1955 or newer sedan. NO station wagons, or pick up trucks. WEIGHT:
More information2017 Senoia Raceway Rulebook Hobby Stock
All drivers must adhere to the general rules, in addition to the division specific rules set forth below. WARNING PLEASE READ All cars with replaced frame or frame rails must first be approved by Track
More informationTORC SERIES COMPETITION RULES FOR SPORTSMAN STOCK TRUCK
TORC SERIES COMPETITION RULES FOR SPORTSMAN STOCK TRUCK Defined As- A two-wheel drive standard size pickup. The truck must be of stock production that has been produced in quantities of at least 5,000
More information2018 Bomber Rules. The rules listed below are now being enforced and are to be added into the rule book
2018 Bomber Rules The rules listed below are now being enforced and are to be added into the rule book for all drivers of the Bomber class to abide by. For questions contact the race track or the technical
More informationLarry King Law s Langley Speedway 2018 Grand Stock Division Rules
2018 Grand Stock Division Rules Amendments: Rules are subject to amendments at any time when ample notice has been given to enhance competition 1. COMPETING MODELS: A. Any American made 1979 through 1988
More informationCrisp Motorsports Park Watermelon Capital Speedway Race Rules Race Car Super Street Class
Crisp Motorsports Park Watermelon Capital Speedway Race Rules Race Car Super Street Class Page 1 of 6 2017 Super Street Rules Vehicle 1. Any 1960 or newer sedan. 2. Chassis and suspension must remain completely
More information2019 ROGER WHEELER CONSTRUCTION ROAD WARRIOR RULES
2019 ROGER WHEELER CONSTRUCTION ROAD WARRIOR RULES PROTEST $350 TOP END/ $400 BOTTOM END ANY ENGINE COMBINATION CRATE ENGINE CLAIM RULE WILL BE $3900. ANY CAR FINISHING ON THE LEAD LAP MAY CLAIM ANY ENGINE
More informationWEIGHT: lbs. Aluminum body or aluminum body panels must add 50 lbs Ford rearend, floater or not, disc brakes or not, must add 100 lbs.
2018 ROAD WARRIOR RULES PROTEST: 1. Top of Motor $200 Bottom $300 2. $50 per shock claim top three only. 3. Tire Protest $100 (one tire) top three only. WHEEL BASE: 1. Minimum 108 wheel base. Must match
More information2013 OPEN WHEEL MODIFIED RULES
2013 OPEN WHEEL MODIFIED RULES BODY: 1970 or newer American passenger cars only. No panel vans or station wagons. Stock appearing front window support units must be used. A minimum window opening of twelve
More information2018 ECONO MOD RULES
P.O. Box 159 Track (330) 772-5481 Hartford, OH 44424 Fax (330) 772-7704 2018 ECONO MOD RULES 1. ROLL CAGE: Roll cage must consist of continuous hoops not less than 1.500 outside diameter. Must be mounted
More information2019 FIGURE 8 RULES INDEX
2019 FIGURE 8 RULES INDEX Battery Body Engine Exhaust System Firewall Fuel Cell Frame Ignition System Rear End Roll Cage Seats Starter Suspension Transmission Weight Rules Wheels and Tires Page 7 Page
More informationWayne County Speedway Super Stock Rules Updated November 20 th 2017
Wayne County Speedway Super Stock Rules Updated November 20 th 2017 Bodies Any American manufactured, steel bodied, production passenger car or small truck (S10, Ranger, Dakota). No full size trucks. No
More information2016 HOBBY STOCK DIVISION RULES
2016 HOBBY STOCK DIVISION RULES DEFINITION OF STOCK OR "OEM": OEM is the abbreviation for original equipment manufacturer. No carbon fiber parts anywhere on the car. MODELS: 1. 1965 or later American mfg.
More information2017 UPDATE 3/6/17 Thunder Car Rules
Mt. Lawn Speedway 2017 UPDATE 3/6/17 Thunder Car Rules The absence of a particular rule does NOT necessarily mean its approval! FRAME 1. Any 1968 and newer, full frame, rear wheel drive full sized car,
More informationPURE MINI STOCK CLAIMERS 2008
SOUTHERN OREGON SPEEDWAY 113 Haskell St., Central Point, OR 97502 541 261 7077 Fax: 541 664 6657 Website: www.sospeedway.com PURE MINI STOCK CLAIMERS 2008 1. MODELS: A. Any front engine, front or rear
More informationGRAND AMERICAN MODIFIED RULES
GRAND AMERICAN MODIFIED RULES *** Please refer to General Section for rules and regulations applicable to all divisions*** CNS Reserves the right to alter or amend the Rules and Regulations in the interest
More information2018 BLUE RIDGE MOTORSPORTS PARK RULEBOOK HOBBY / 602
2018 BLUE RIDGE MOTORSPORTS PARK RULEBOOK HOBBY / 602 The rules and/or regulations set forth herein are designed to provide for the orderly conduct of racing events and to establish minimum acceptable
More informationPLEASE READ AND UNDERSTAND GENERAL RULES PERTAINING TO ALL RACERS AND RACECARS
NEVADA SPEEDWAY 2018 Mid-West Mods PLEASE READ AND UNDERSTAND GENERAL RULES PERTAINING TO ALL RACERS AND RACECARS COMMUNICATIONS: All competitors must have a RACEceiver in car radio to compete at the Raceway.
More information1- Any stock appearing metal bodied four cylinder car or truck through the current year.
Super Stock 4 2018 Rules 1- Any stock appearing metal bodied four cylinder car or truck --1965 through the current year. 2- You may run an aftermarket fabricated body. The body must be made from magnetic
More informationDRIVER ELIGIBILITY GUIDELINES TO RACE CLASSES
SPORTSMAN RULES DRIVER ELIGIBILITY GUIDELINES TO RACE CLASSES Any DRIVER that has won a CRATE / Limited/ Super Late Model Feature event at Boyd's Speedway in 2017 cannot register to race in any class lower
More information2012 Pro Stock Rules
2012 Pro Stock Rules Areas highlighted in red are changes for 2012 Revised 5-5-2012 PRO STOCK: Any North American made car 1968 to present. This division was created as a controlled, economical and competitive
More information2019 BARBERTON SPEEDWAY MODIFIED RULES. Any driver without a scanner will be sent to the rear.
2019 BARBERTON SPEEDWAY MODIFIED RULES Any driver without a scanner will be sent to the rear. The following rules are set as a guide, and are in no way a guarantee against injury or death to participants,
More information2017 Wagner Speedway Late Model Rules
2017 Wagner Speedway Late Model Rules RULE BOOK DISCLAIMER The rules and/or regulations set forth herein are designed to provide for the orderly conduct of racing events and to establish minimum acceptable
More information2018 Senoia Raceway Rulebook Limited Late Model
All drivers must adhere to the general rules, in addition to the division specific rules set forth below. Senoia Raceway Limited Late division allows four engine packages. A. 604 Crate Engine 2250lbs 8
More informationCYLINDER TRUCK RULES
2019 4 CYLINDER TRUCK RULES The rules herein shall refer to Adirondack International Speedway as AIS. These rules are intended to create affordable and fair competition. While they offer a good outline,
More information3. Bumpers: Steel tube front and rear bumpers are required. Bumpers must be centered at 19 inches from the ground, +/- 2 inches.
THUNDERCAR RULES * These rules may be amended at the official s discretion. * No additions, subtractions, alterations, or non-oem type parts allowed unless specifically allowed in the rules. Visiting cars
More informationdog hollow speedway official 2017 pure/hobby/strictly stock rules
dog hollow speedway official 2017 pure/hobby/strictly stock rules 1. GENERAL This division is open to any North American made passenger car from 1965 through the present. The make and model must be factory
More information2018 SUPER PRO TRUCK RULES
2018 SUPER PRO TRUCK RULES INDEX Battery Brake Components Bodys Competing Models Electrical Switches Engine Location Engine Option 1 - Crate Engine Option 2 - SPT Exhaust System Fuel Cell Frame Hood Ignition
More information2016 DIRTcar Sport Compact TO ALL COMPETITORS/PARTICIPANTS
2016 DIRTcar Sport Compact TO ALL COMPETITORS/PARTICIPANTS Under the guideline of the 2016 DIRTcar Sport Compact rules any and/or rules and as stated in the 2016 DIRTcar Rule Book, all DIRTcar rules apply
More information#100 TO #199 SPORTSMAN 1600 LIGHT BUGGY TECHNICAL SPECIFICATIONS
#100 TO #199 SPORTSMAN 1600 LIGHT BUGGY TECHNICAL SPECIFICATIONS DEFINITION 1600 Light Buggy is a one-person, limited 4-wheel car using Volkswagen type 1 stock components with a 1585 cc engine. All parts
More informationThunder Bomber 2019 GENERAL
Thunder Bomber 2019 GENERAL - Tech man has right to check this every week. 1. No nitrous or traction control. 2. After 3 times of refusing to tear down - you will be disqualified from competing in this
More informationPLEASE BE SURE YOU HAVE READ AND UNDERSTAND THE GENERAL RULES,SAFETY RULES AND DRIVER SAFETY EQUIPMENT BEFORE CONTINUING.
2017 MOD MINI RULES Changes for 2017 are highlighted in red *Speedway Officials shall be empowered to permit minor deviations from any of the specifications herein or impose any further restrictions that
More informationEach track is responsible for their own fuel rule Fuel is to be NON OXYGENATED and must conform to their local track
Stock 4 Rule Clarification: SECA Stock 4 will go by MMSA Rules This was the intention. So if there is any discrepancy between these rules and mmsa rules then please refer to the mmsa rule book. Fuel: Each
More information2017/2018 DIRTcar Stock Car Rules
2017/2018 DIRTcar Stock Car Rules TO ALL COMPETITORS/PARTICIPANTS V5 (3 12 17)! The following are the 2017/2018 DIRTcar Stock Car rules. All amendments supersede any previous rules regarding any technical
More informationLarry King Law s Langley Speedway 2018 Super Street Division Rules
Larry King Law s Langley Speedway 2018 Super Street Division Rules 1. COMPETING MODELS: A. Any American made 1979 through 1988 two door, coupe with a minimum 108 inch wheelbase. B. Cars must have a full
More information2018 FTMS MINI TRUCK RULES
2018 FTMS MINI TRUCK RULES 1. CHASSIS SPECIFICATIONS: Class is open to any chassis that meets spec. Truck - 70 wheelbase.095. Main frame rail const. 1 ¼ square tube..095. Main cage tube supports, 11/4x.095
More informationTORC SERIES COMPETITION RULES FOR SPORTSMAN 1600 BUGGY
TORC SERIES COMPETITION RULES FOR SPORTSMAN 1600 BUGGY DEFINED AS- A limited 4-wheel vehicle utilizing a type-1, 1600 c.c. Volkswagen air-cooled engine with one person in the vehicle. Division rules supersede
More informationPRO-4 MODIFIEDS 2017 RULES
PRO-4 MODIFIEDS 2017 RULES 1. CAGES / CHASSIS a. Fabricated Chassis only. b. Minimum 1 1/2" Diameter.095 wall tubing. c. Must be 4-post cage with a minimum of 3 U-shaped door bars on drivers side; door
More information2017 Northeast Wingless Sprint Rules
2017 Northeast Wingless Sprint Rules If your question is not in these rules, do not assume it is legal. Ask first! This class Northeast Wingless Sprint Cars is intended to offer an affordable sprint car
More information2018 CHARGER DIVISION RULES
! 2018 CHARGER DIVISION RULES Jennerstown Speedway (Intersections of Rt. 30 & Rt. 985) PO Box 270 206 Somerset Street Jennerstown, PA 15547-0099 Track Phone: 814.703.8009 Fax: 814.703.8163 For Track Promoter
More information2018 MODIFIED Rules RULE BOOK DISCLAIMER
2018 MODIFIED Rules RULE BOOK DISCLAIMER The rules and/or regulations set forth herein are designed to provide for the orderly conduct of racing events and to establish minimum acceptable requirements
More information2009 PASS MOD Rules MODS Tire Policy
2009 PASS MOD Rules 2009 MODS Tire Policy The American Racer 9 EC83 left and EC84 right is the mandated tire for the 2009 race season. All tires must be purchased through Northern Race Tire. Each team
More information2018 Sportsman Rules (SUPER STREET, PRO STOCK, LIMITED SPORTSMAN)
2018 Sportsman Rules (SUPER STREET, PRO STOCK, LIMITED SPORTSMAN) (Northeast DIRTcar Sportsman Modifieds are listed under Sportsman Modifieds) (Northeast DIRTcar Pro Stocks are listed under Northeast Pro
More informationPETALUMA SPEEDWAY SUPER STOCK RULES Current as of April 1, 2016
2015-2018 PETALUMA SPEEDWAY SUPER STOCK RULES Current as of April 1, 2016 As of 04/01/2016 Table of Contents 1 Safety Equipment... 2 2 Weight... 4 3 Chassis... 4 4 Bumpers, Nerf Bars & Rub Rails... 5 5
More information2015 RULES Sportsman/Super St./Outlaws
2015 RULES Sportsman/Super St./Outlaws For Tech Questions: Charlie Rockwell 802-355-8112 Head and neck restraint will be required (Hutchens, Hans, ect.) Safety check list for Loudon a. approved drivers
More information