INSTALLATION GUIDE. Directed Digital Solutions HONDA4. Designed by Installers for Installers

Transcription

1 INSTALLATION GUIDE Directed Digital Solutions HONDA4 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle s electrical system and components

2 Contents Warning! Safety first... 3 Introduction... 4 Pre-installation and application warnings... 4 Vehicle application guide... 5 Wiring connections... 6 Main power harness (H1), 12-pin thick gauge connector... 6 Auxiliary output harness (H2), 16-pin black connector... 6 Analog harness (H3), 18-pin white connector... 7 MC501 harness (H4), 8 thick-gauge wires (optional)... 7 Installation (wiring diagrams & vehicle wiring reference charts)... 8 Type 1 with T-Harness (THHOC5)... 8 Type Type 2 with T-Harness (THHOC6) Type Type 3 with T-Harness (THHOC6) Type Type 4 with T-Harness (THHOC5) Type Type 5 with T-Harness (THHOC5) Type Type 6 with T-Harness (THHOC5) Type Type 7 with T-Harness (THHOC5) Type Type Type Type Type Connecting the module Important! Manual or automatic transmission selection Optional sensors RF Systems When used in conjunction with SmartStart Module programming LED diagnostics and troubleshooting Soft reset Hard reset Learning the Tach (not needed with Virtual Tach) Initializing Virtual Tach (not needed with hardwired or data tach applications) Limited lifetime consumer warranty Quick Reference Guide... 53

3 Warning! Safety first The following safety warnings must be observed at all times: Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation. The following precautions are the sole responsibility of the user; however, authorized Directed dealers should: Never use a test light or logic probe when installing this unit. Always use a multimeter. Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage). When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed toggle switch. It is the user s sole responsibility to properly handle and keep out of reach from children all remote controls to assure that the system does not unintentionally remote start the vehicle. USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES. Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately. OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS. Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged parking brake. Do not allow anyone to stand in front of or behind the vehicle. This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such vehicles may pose certain risk. 3 Directed Digital Solutions HONDA4

4 Introduction The HONDA4 firmware for Directed Digital Solutions is compatible with specific Acura and Honda vehicles. It is a complete solution for remote start, security (if applicable), bypass interface, and convenience. This guide provides information on the installation of the module using HONDA4. If you would prefer using this system as a digital solution, go to and search for the make, model and year of the vehicle. This will allow you to find the proper firmware and corresponding installation guide. Warning! This module can only be programmed via the web tool, which can be found on or using the Directechs Mobile application for mobile devices. Features and functions will become accessible when you connect the module using the XKLoader. Pre-installation and application warnings Firmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle limitations. T-Harness compatible THHOC5 OR THHOC6 Keys required for programming 1 Keys required for operation 0 The optional Plug & Play THHOC5 OR THHOC6 T-Harnesses are sold separately. See "Wiring diagram with T-Harness" to determine which T-Harness option is compatible with your specific vehicle. [5] The Honda Pilot, Ridgeline, Acura MDX & Acura TL are NOT compatible with optional T-Harness THHOC5 & THHOC6. The OBDII Diagnostic Connector features will remain the same even when the T-Harness is installed. All connectors are displayed from the wire side (unless specified otherwise). Refer to the "Vehicle wiring reference chart" following each installation type. General notes: This section highlights important information for this specific firmware. [1] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin. [2] The connection is ONLY required when enabling the security features during module flashing. [3] Connect this wire ONLY if the Trunk Release feature is not supported in data. See the "Vehicle application guide" on page 5 for more information on supported features. [4] The Green wire is ONLY required for starter disable and antigrind applications. [5] If available, the vehicle High Speed F-CAN connections are ONLY required for the Automatic VIN Detection, when using the DirectLink application and/or SmartStart advanced features. Additional parts required (maximum required): 87 Diode 6A 0 x 1A Diodes 87a x Relay esistor x Resistor Fuse 7.5A 0 x Fuse 4 Directed Digital Solutions HONDA4

5 Vehicle application guide The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle. Vehicles PK-Immobilizer Bypass-Data No Key Req'd DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock DL-Sliding Door Control Driver DL-Sliding Door Control Passenger DL-Trunk / Hatch Release FOB-Control of aftermarket alarm with OEM remote RS-3x LOCK START (Start control using OEM Remote) Acura CSX EL MDX MDX RDX RL RSX TL TSX Honda Accord Accord Hybrid Civic Civic Civic Hybrid Civic Hybrid CR-V CR-V CR-Z Element Fit Fit 5 5 Insight 3 Odyssey Pilot Ridgeline Legend: AV: Horn & Light Controls CC: Comfort & Convenience Controls DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w/ FOB Remote PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status RS-Remote Start Takeover RS-SmartStart RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin ST-Brake Status (foot brake) ST-Door Locks Status ST-E-Brake Status 5 Directed Digital Solutions HONDA4

6 Wiring connections The wiring connections listed below are specific to this firmware. Main power harness (H1), 12-pin thick gauge connector Conn./Pin Color Description H1/1 White Relay 3 COM Parking Light Output 1 H1/2 White/Brown Relay 3 N.O. Parking Light Input 1 H1/3 Brown/Red Relay 2 N.O No Connection. H1/4 Yellow/Red Relay 2 COM Security Light Interrupt (vehicle side) H1/5 Orange/Red Relay 2 N.C. Security Light Interrupt (connector side) H1/6 Yellow Relay 1 COM Ignition Interrupt (vehicle side) Input 1 H1/7 White Relay 3 COM (+) Parking Light Output 1 H1/8 White/Brown Relay 3 N.O. (+) Parking Light Input 1 H1/9 Black (-) Ground H1/10 Red (+) 12 Volt (battery) H1/11 Orange/Yellow Relay 1 N.C. Ignition Interrupt (connector side) Input H1/12 Brown Relay 1 N.O. (+) Power 12 Volt 1 Auxiliary output harness (H2), 16-pin black connector Conn./Pin Color Description H2/1 Violet/Brown No Connection H2/2 Yellow/Black Door Lock Data H2/3 Orange/Black Immobilizer Data H2/4 Tan HS CAN Low H2/5 Tan/Black HS CAN High H2/6 Light Green Single Wire CAN H2/7 Orange/Green No Connection H2/8 Orange/Brown No Connection H2/9 Violet/Green No Connection H2/10 Green/Black (-) Lock Output H2/11 White/Violet No Connection 2 H2/12 White/Red No Connection 2 H2/13 Lt. Blue/Black (-) Unlock Output H2/14 Green/Red No Connection 2 H2/15 N/A No Connection H2/16 Violet/Yellow No Connection 1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. 2. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. 6 Directed Digital Solutions HONDA4

7 Analog harness (H3), 18-pin white connector Conn./Pin Color Description H3/1 Lt. Blue/Red (-) Door Lock Activation Input H3/2 Black/White (-) Parking Brake Input (manual transmission) 2 H3/3 Gray (-) Hood Input 2 H3/4 N/A No Connection H3/5 Gray/Black (+) Glow Plug Input 2 H3/6 Violet/White (AC) Tach Input 2 H3/7 Dark Blue (-) Unlock Output 1 H3/8 Brown/Black (-) Horn 1 H3/9 Red/White (-) Trunk Release Output 1 H3/10 White/Green (-) Door Input 2 H3/11 Yellow/Green (+) Door Input 2 H3/12 Blue/Red No Connection H3/13 Light Blue (-) Trunk Trigger Input 2 H3/14 Pink/Yellow (-) Activation (start) Input H3/15 Dark Green (-) Lock Output 1 H3/16 Brown/White (+) Brake Input 2 H3/17 Brown (+) Siren Output 1 H3/18 Blue/White (-) Ground When Running (status) Output 1 MC501 harness (H4), 8 thick-gauge wires (optional) Conn./Pin Color Description H4/1 Pink/White (+) Ignition 2/Flex Relay Output 3 H4/2 Red/White (+) Fused (30A) Ignition 2/Flex Relay Input H4/3 Pink (+) Ignition Output (also input to Yellow in ribbon cable) H4/4 Red (+) 12 Volt (battery) Input H4/5 Orange (+) Accessory Output H4/6 Red (+) 12 Volt (battery) Input H4/7 Green Starter Input (from key switch) 4 H4/8 Violet (+) Starter Output (to starter) 1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. 2. These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle application guide" on page 5 for a list of compatible features. 3. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. 4. The Green wire is only required for starter disable and anti-grind applications. 7 Directed Digital Solutions HONDA4

8 Installation (wiring diagrams & vehicle wiring reference charts) Type 1 with T-Harness (THHOC5) Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). Parking Lights: Red/Black, pin Fuse/Relay Box (green conn. under drivers side dash) Ignition Switch (white or brown conn. and ignition cylinder) Immobilizer Connector (white or green conn. at ignition barrel) Single Wire CAN: pin 4 Fuse/Relay Box (green conn. under drivers side dash) Single Wire CAN: Lt. Green 16-pin Black Connector Remote Start Safety Override Switch THHOC5 (optional T-Harness) The Remote Start Safety Override Switch MUST be in the ON position. Hood Pin (-) Hood Input: Gray: 3 12-pin White Connector White: (+) Parking Light Output (+) Siren Output: Brown: 17 Siren 8 Directed Digital Solutions HONDA4

9 Type 1 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). Fuse/Relay Box (conn. under drivers side dash) Parking Lights: Red/Black, pin Cut Fuse/Relay Box (Green conn. under drivers side dash) (+) Starter: pin Ignition Switch (white or brown conn. at ignition cylinder) Single Wire CAN: pin 4 (+) 12V: pin 3 (+) Ignition: pin 6 (+) Accessory 2: pin 5 (+) Accessory 1: pin 4 (+) Starter Output (car side): Violet: 8 Starter Input (key side): Green: 7 (+) 12V Input: Red: 6 (+) Accessory 1 Output: Orange: 5 (+) 12V Input: Red: 4 (+) Ignition Input/Output: Pink: 3 (+) 12V Input: Red/White: 2 (+) Accessory 2 Output: Pink/White: 1 Hood Pin Immobilizer Data: Orange/Black: 3 8 thick-gauge wires Single Wire CAN: Lt. Green: 6 MC501 4 White 7 White (-) Hood Input: Gray: 3 Immobilizer Data: pin 2 Immobilizer conn. (white or green conn. at ignition barrel) 10: Red: (+) 12V Input 9: Black: (-) Ground Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. 5: Orange/Red: Security Light Interrupt (conn side) Security Light: pin Siren (+) Siren Output: Brown: 17 4: Yellow/Red: Security Light Interrupt (vehicle side) 2 & 8: White/Brown: (+) Parking Light Input 1 & 7: White: (+) Parking Light Output 9 Directed Digital Solutions HONDA4

10 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Acura TL V Brown/Black 3 (+) Ignition switch. Brown 7 B Starter Black/White or Black 1 (+) Ignition switch. Brown 7 B Ignition Black/Yellow 6 (+) Ignition switch. Brown 7 B Accessory Black/Red 4 (+) Ignition switch. Brown 7 B Accessory 2 White/Red 5 (+) Ignition switch. Brown 8 B SW CAN Brown/Black 4 Data Drivers fuse/relay box. Green 21 D Immobilizer Data Yellow 2 Data Immobilizer connector. White 7 A Security Light Orange 5 Data Immobilizer connector. White 7 A Parking Lights Red/Black 31 (+) Drivers fuse/relay box. White 45 C Acura TSX V White 3 (+) Ignition switch. Brown 7 B Starter Black/White or Black 1 (+) Ignition switch. Brown 7 B Ignition Black/Yellow 6 (+) Ignition switch. Brown 7 B Accessory Black/Red 4 (+) Ignition switch. Brown 7 B Accessory 2 White/Red 5 (+) Ignition switch. Brown 7 B SW CAN Brown/Black 4 Data Drivers fuse/relay box. Green 21 D Immobilizer Data Red/Blue 2 Data Immobilizer connector. White 7 A Security Light Blue/Orange 5 Data Immobilizer connector. White 7 A Parking Lights Red/Black 31 (+) Drivers fuse/relay box. White 45 C Acura TSX V White 3 (+) Ignition switch. Brown 7 B Starter Black/White or Black 1 (+) Ignition switch. Brown 7 B Ignition Black/Yellow 6 (+) Ignition switch. Brown 7 B Accessory Black/Red 4 (+) Ignition switch. Brown 7 B Accessory 2 White/Red 5 (+) Ignition switch. Brown 7 B SW CAN Brown/Red 4 Data Drivers fuse/relay box. Green 21 D Immobilizer Data Red 2 Data Immobilizer connector. Green 7 A Security Light Orange 5 Data Immobilizer connector. Green 7 A Parking Lights Red/Black 31 (+) Drivers fuse/relay box. White 45 C 10 Directed Digital Solutions HONDA4

11 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Honda Accord V White 3 (+) Ignition switch. Brown 7 B Starter Black/White or Black 1 (+) Ignition switch. Brown 7 B Ignition Black/Yellow 6 (+) Ignition switch. Brown 7 B Accessory Black/Red 4 (+) Ignition switch. Brown 7 B Accessory 2 White/Red 5 (+) Ignition switch. Brown 7 B SW CAN Brown/Red 4 Data Drivers fuse/relay box. Green 21 D Immobilizer Data Red/Blue 2 Data Immobilizer connector. Green 7 A Security Light Blue/Orange 5 Data Immobilizer connector. Green 7 A Parking Lights Red/Black 31 (+) Drivers fuse/relay box. White 45 C Honda Accord Hybrid V White 3 (+) Ignition switch. Brown 7 B Starter Black/White or Black 1 (+) Ignition switch. Brown 7 B Ignition Black/Yellow 6 (+) Ignition switch. Brown 7 B Accessory Black/Red 4 (+) Ignition switch. Brown 7 B Accessory 2 White/Red 5 (+) Ignition switch. Brown 7 B SW CAN Brown/Red 4 Data Drivers fuse/relay box. Green 21 D Immobilizer Data Yellow 2 Data Immobilizer connector. Green 7 A Security Light Red 5 Data Immobilizer connector. Green 7 A Parking Lights Red/Black 31 (+) Drivers fuse/relay box. White 45 C 11 Directed Digital Solutions HONDA4

12 Type 2 with T-Harness (THHOC6) Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). OBDII Diagnostic (black conn. under driver side dash, connector side view) Ignition Switch (white or brown conn. and ignition cylinder) Immobilizer Connector (green conn. at ignition cylinder) F-CAN High: White, pin F-CAN Low: Red, pin 14 HS Can Low: Tan HS Can High: Tan/Black 16-pin Black Connector Remote Start Safety Override Switch THHOC6 (optional T-Harness) Refer to the Vehicle wiring reference charts and for more information on wire and connector details. The Remote Start Safety Override Switch MUST be in the ON position. Hood Pin (-) Hood Input: Gray: 3 (-) Power Liftgate Output: Red/White: 9 12-pin White Connector White: (+) Parking Light Output Siren (+) Siren Output: Brown: Directed Digital Solutions HONDA4

13 Type 2 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). Immobilizer Connector (green conn. at ignition cylinder) Immobilizer Data, pin 3 Single Wire CAN, pin F-CAN High: White, pin 6 OBDII Diagnostic 8 (black conn. under driver side dash, 16 connector side view) F-CAN Low: Red, pin 14 Refer to the Vehicle wiring reference charts and for more information on wire and connector details. Immobilizer Data: Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 Single Wire CAN: Lt. Green: 6 (+) Starter: pin (+) 12V: pin 3 (+) Ignition: pin 6 (+) Accessory: pin 4 (+) Starter Output (car side): Violet: 8 Starter Input (key side): Green: 7 (+) 12V Input: Red: 6 (+) Accessory Output: Orange: 5 (+) 12V Input: Red: 4 (+) Ignition Input/Output: Pink: 3 (+) Fused (30A) Ignition 2/ Flex Relay Input: Red/White: 2 (+) Ignition 2/Flex Relay Output: Pink/White: 1 8 thick-gauge wires MC501 4 White 7 White 10: Red: (+) 12V Input Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. Ignition Switch (white or brown conn. at ignition cylinder) Hood Pin (-) Hood Input: Gray: 3 9: Black: (-) Ground (-) Power Liftgate Output: Red/White: 9 2 & 8: White/Brown: (+) Parking Light Input (+) Siren Output: Brown: 17 Siren 1 & 7: White: (+) Parking Light Output 13 Directed Digital Solutions HONDA4

14 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Acura MDX V White 3 (+) Ignition switch. Brown 7 B Starter Yellow 1 (+) Ignition switch. Brown 7 B Ignition Pink 6 (+) Ignition switch. Brown 7 B Accessory Orange 4 (+) Ignition switch. Brown 7 B F-CAN High White 6 Data OBDII. Gray 16 C F- CAN Low Red 14 Data OBDII. Gray 16 C SW CAN Lt. Green 4 Data Immobilizer connector. Green 7 A Immobilizer Data Lt. Green 3 Data Immobilizer connector. Green 7 A Parking Lights Gray N/A (+) Driver kick, harness to rear. N/A N/A D Power Liftgate Brown & White 18 & 6 Short Drivers fuse/relay box. Green N/A E 14 Directed Digital Solutions HONDA4

15 Type 3 with T-Harness (THHOC6) Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). OBDII Diagnostic (black conn. under driver side dash, connector side view) Ignition Switch (white or brown conn. and ignition cylinder) Immobilizer Connector (green or white conn. at ignition barrel) F-CAN High: White, pin F-CAN Low: Red, pin 14 HS Can Low: Tan HS Can High: Tan/Black 16-pin Black Connector Remote Start Safety Override Switch THHOC6 (optional T-Harness) Refer to the Vehicle wiring reference charts and for more information on wire and connector details. Hood Pin (-) Hood Input: Gray: 3 (-) Trunk Release Output: Red/White: 9 The Remote Start Safety Override Switch MUST be in the ON position. 12-pin White Connector White: (+) Parking Light Output (+) Siren Output: Brown: 17 Siren 15 Directed Digital Solutions HONDA4

16 Type 3 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). Immobilizer Connector (green or white conn. at ignition barrel) Immobilizer Data, pin 3 Single Wire CAN, pin F-CAN High: White, pin 6 OBDII Diagnostic 8 (black conn. under driver side dash, 16 connector side view) F-CAN Low: Red, pin 14 Refer to the Vehicle wiring reference charts and for more information on wire and connector details. Immobilizer Data: Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 Single Wire CAN: Lt. Green: 6 (+) Starter: pin (+) 12V: pin 3 (+) Ignition:pin 6 (+) Accessory: pin 4 (+) Starter Output (car side): Violet: 8 Starter Input (key side): Green: 7 (+) 12V Input: Red: 6 (+) Accessory Output: Orange: 5 (+) 12V Input: Red: 4 (+) Ignition Input/Output: Pink: 3 (+) Fused (30A) Ignition 2/ Flex Relay Input: Red/White: 2 (+) Ignition 2/Flex Relay Output: Pink/White: 1 8 thick-gauge wires MC501 4 White 7 White 10: Red: (+) 12V Input Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. Ignition Switch (white or brown conn. at ignition cylinder) Hood Pin (-) Hood Input: Gray: 3 (-) Trunk Release Output: Red/White: 9 9: Black: (-) Ground 2 & 8: White/Brown: (+) Parking Light Input (+) Siren Output: Brown: 17 Siren 1 & 7: White: (+) Parking Light Output 16 Directed Digital Solutions HONDA4

17 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Acura CSX Starter Yellow 1 (+) Ignition switch. Brown 7 B 12V Pink 3 (+) Ignition switch. Brown 7 B Ignition Blue 6 (+) Ignition switch. Brown 7 B Accessory Orange 4 (+) Ignition switch. Brown 7 B SW CAN Lt. Green 4 Data Immobilizer connector. White 7 A Immobilizer Data Lt. Green 3 Data Immobilizer connector. White 7 A Parking Lights Gray N/A (+) Driver kick, harness to rear. N/A N/A E Trunk Release Green N/A (+) Driver kick, harness to rear. N/A N/A E F-CAN High N/A N/A N/A N/A N/A N/A N/A F-CAN Low N/A N/A N/A N/A N/A N/A N/A Acura RDX V White 3 (+) Ignition switch. Brown 7 B Starter Lt. Green 2 (+) Ignition switch. Brown 7 B Ignition Blue 6 (+) Ignition switch. Brown 7 B Accessory Orange 4 (+) Ignition switch. Brown 7 B F-CAN High White 6 Data OBDII. Gray 16 C F- CAN Low Red 14 Data OBDII. Gray 16 C SW CAN Pink 4 Data Immobilizer connector. White 7 A Immobilizer Data Lt. Green 3 Data Immobilizer connector. White 7 A Parking Lights Red 19 (+) Drivers fuse/relay box. Green 42 D Trunk Release Pink 13 (-) Drivers fuse/relay box. Green 42 D 17 Directed Digital Solutions HONDA4

18 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Honda Civic V White 3 (+) Ignition switch. White 7 B Starter Yellow 1 (+) Ignition switch. White 7 B Ignition Blue 6 (+) Ignition switch. White 7 B Accessory Orange 4 (+) Ignition switch. White 7 B F-CAN High White 6 Data OBDII. Gray 16 C F- CAN Low Red 14 Data OBDII. Gray 16 C SW CAN Pink 4 Data Immobilizer connector. Gray 7 A Immobilizer Data Lt. Green 3 Data Immobilizer connector. Gray 7 A Parking Lights Gray 29 (+) Drivers fuse/relay box. Green 42 D Trunk Release Green 9 5-wire Drivers fuse/relay box. Green 42 D Honda Civic Hybrid V White 3 (+) Ignition switch. White 7 B Starter Yellow 1 (+) Ignition switch. White 7 B Ignition Blue 6 (+) Ignition switch. White 7 B Accessory Orange 4 (+) Ignition switch. White 7 B F-CAN High White 6 Data OBDII. Gray 16 C F- CAN Low Red 14 Data OBDII. Gray 16 C SW CAN Pink 4 Data Immobilizer connector. White 7 A Immobilizer Data Lt. Green 3 Data Immobilizer connector. White 7 A Parking Lights Red 19 (+) Drivers fuse/relay box. Green 42 D Trunk Release Green 9 5-wire Drivers fuse/relay box. Green 42 D Honda CR-V V White 3 (+) Ignition switch. Brown 7 B Starter Yellow 1 (+) Ignition switch. Brown 7 B Ignition Blue 6 (+) Ignition switch. Brown 7 B Accessory Orange 4 (+) Ignition switch. Brown 7 B F-CAN High White 6 Data OBDII. Gray 16 C F- CAN Low Red 14 Data OBDII. Gray 16 C SW CAN Pink 4 Data Immobilizer connector. White 7 A Immobilizer Data Green 3 Data Immobilizer connector. White 7 A Parking Lights Red 1 (+) Above driver kick. Blue 18 D Trunk Release White 13 (-) Drivers fuse/relay box. Green 42 D Honda CR-Z V White 3 (+) Ignition switch. Brown 7 B Starter Red 1 (+) Ignition switch. Brown 7 B Ignition Yellow 5 (+) Ignition switch. Brown 7 B Accessory Orange 7 (+) Ignition switch. Brown 7 B F-CAN High Green 6 Data OBDII. Gray 16 C F- CAN Low Pink 14 Data OBDII. Gray 16 C SW CAN Green 4 Data Immobilizer connector. Green 7 A Immobilizer Data Pink 3 Data Immobilizer connector. Green 7 A Parking Lights Red 37 (+) Drivers fuse/relay box. Green 49 D Trunk Release Pink 4 (-) Drivers fuse/relay box. Green 49 D 18 Directed Digital Solutions HONDA4

19 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Honda Fit V White 3 (+) Ignition switch. Brown 7 B Starter Red 1 (+) Ignition switch. Brown 7 B Ignition Yellow 6 (+) Ignition switch. Brown 7 B Accessory Orange 4 (+) Ignition switch. Brown 7 B F-CAN High White 6 Data OBDII. Gray 16 C F- CAN Low Red 14 Data OBDII. Gray 16 C SW CAN Lt. Green 4 Data Immobilizer connector. Green 7 A Immobilizer Data Green 3 Data Immobilizer connector. Green 7 A Parking Lights Gray 42 (+) Drivers fuse/relay box. Green 49 D Honda Insight V White 3 (+) Ignition switch. Brown 7 B Ignition Yellow 6 (+) Ignition switch. Brown 7 B Accessory Orange 4 (+) Ignition switch. Brown 7 B Starter Red 1 (+) Ignition switch. Brown 7 B F-CAN High White 6 Data OBDII. Gray 16 C F- CAN Low Red 14 Data OBDII. Gray 16 C SW CAN Green 4 Data Immobilizer connector. Green 7 A Immobilizer Data Lt. Green 3 Data Immobilizer connector. Green 7 A Parking Lights Gray 42 (+) Drivers fuse/relay box. Green 49 D Trunk Release Pink 17 (-) Drivers fuse/relay box. Green 49 D 19 Directed Digital Solutions HONDA4

20 Type 4 with T-Harness (THHOC5) Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). OBDII Diagnostic (black conn. under driver side dash, connector side view) F-CAN High: White, pin Keyless Receiver Unit (green conn. left of steering column) 9 16 F-CAN Low: Red, pin 14 Ignition Switch (white or brown conn. and ignition cylinder) Immobilizer Connector (green conn. at ignition barrel) Keyless Data: Blue/Orange, pin 2 OR Keyless Data: Blue/Orange, pin 2 HS Can Low: Tan HS Can High: Tan/Black Keyless Data: Yellow/Black 16-pin Black Connector Remote Start Safety Override Switch THHOC5 (optional T-Harness) Keyless Entry Module (green conn. rear of drivers fuse/relay box) The Remote Start Safety Override Switch MUST be in the ON position. Yellow: Ignition Interrupt (vehicle side) Cut Refer to the Vehicle wiring reference charts and for more information on wire and connector details. Hood Pin OR (-) Hood Input: Gray: 3 (AC) Tach Input: Violet/White: 6 (-) Trunk Release Output: Red/White: 9 (-) Door Input: White/Green: 10 (-) Trunk Input: Lt. Blue: 13 (+) Brake Input: Brown/White: 16 (+) Siren Output: Brown: pin White Connector Orange/Yellow: Ignition Interrupt (conn. side) White: (+) Parking Light Output Fuse/Relay Box (green conn. at drivers fuse/relay box) Parking Lights: Red/Yellow, pin 15 Siren Fuse/Relay Box (green conn. at drivers fuse/relay box) Parking Lights: Red/Yellow, pin 9 OR 20 Directed Digital Solutions HONDA4

21 Type 4 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). Ignition Switch (white or brown conn. at ignition cylinder) (+) Starter: pin 1 (+) Accessory: pin Keyless Receiver Unit (Green conn. left of steering column) (+) 12V: pin 3 (+) Ignition:pin Keyless Data: Blue/Orange, pin 2 (+) Starter Output (car side): Violet: 8 Starter Input (key side): Green: 7 (+) 12V Input: Red: 6 (+) Accessory Output: Orange: 5 (+) 12V Input: Red: 4 (+) Ignition Input/Output: Pink: 3 (+) Fused (30A) Ignition 2/ Flex Relay Input: Red/White: 2 (+) Ignition 2/Flex Relay Output: Pink/White: 1 8 thick-gauge wires OR MC501 Keyless Data: Blue/Orange, pin Keyless Entry Module (green conn. rear of drivers fuse/relay box) 4 White 7 White Keyless Data: Yellow/Black: 2 Immobilizer Data: Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: F-CAN High: White, pin 6 OBDII Diagnostic 8 (black conn. under driver side dash, 16 connector side view) F-CAN Low: Red, pin 14 Immobilizer conn. (green connector at ignition barrel) Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. Immobilizer Data: pin 2 Cut Security Light: pin Hood Pin OR (-) Hood Input: Gray: 3 11: Orange/Yellow: Ignition Interrupt (conn. side) Refer to the Vehicle wiring reference charts and for more information on wire and connector details. (AC) Tach Input: Violet/White: 6 (-) Trunk Release Output: Red/White: 9 (-) Door Input: White/Green: 10 (-) Trunk Input: Lt. Blue: 13 (+) Brake Input: Brown/White: 16 (+) Siren Output: Brown: 17 10: Red: (+) 12V Input 9: Black: (-) Ground 6: Yellow: Ignition Interrupt (veh. side) 5: Orange/Red: Security Light Interrupt (conn. side) 4: Yellow/Red: Security Light Interrupt (veh. side) 2 & 8: White/Brown: (+) Parking Light Input 1 & 7: White: (+) Parking Light Output Cut Siren Fuse/Relay Box (green conn. at drivers fuse/relay box) Fuse/Relay Box (green conn. at drivers fuse/relay box) Parking Lights: Parking Lights: Red/Yellow, pin 9 Red/Yellow, pin 15 OR 21 Directed Digital Solutions HONDA4

22 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Acura EL V White 3 (+) Ignition switch. Brown 7 B Starter Black/White 1 (+) Ignition switch. Brown 7 B Ignition Black/Yellow 6 (+) Ignition switch. Brown 7 B Accessory Black/Red 4 (+) Ignition switch. Brown 7 B F-CAN High N/A N/A N/A N/A N/A N/A N/A F- CAN Low N/A N/A N/A N/A N/A N/A N/A Immobilizer Data Red/Blue 2 Data Immobilizer connector. Green 7 A Security Light Blue/Orange 5 Cut Immobilizer connector. Green 7 A Keyless Data Blue/Orange 2 Data Rear of drivers fuse/relay box. Green 17 E Parking Lights Red/Yellow 15 (+) Fuse/relay box, third row right connector. Green 18 F Ignition Interrupt Yellow 11 Cut OEM security module above driver kick. Black & White 20 G Drivers Door Trigger Green 20 (-) OEM security module above driver kick. Black & White 20 G Passenger Door Trigger Lt. Green/Red 9 (-) OEM security module above driver kick. Black & White 20 G Drivers Rear Door Trigger Green/White 15 (-) OEM security module above driver kick. Black & White 20 G Passenger Rear Door Trigger Green/White 19 (-) OEM security module above driver kick. Black & White 20 G Trunk Release Yellow/Green 16 (+) OEM security module above driver kick. Black & White 20 G Trunk Trigger Blue/Yellow 7 (-) OEM security module above driver kick. Black & White 20 G Hood Trigger Green 18 (-) OEM security module above driver kick. Black & White 20 G Tach Blue 5 AC Fuse/relay box, second row on right. Green 13 D Brake White/Black 3 (+) Fuse/relay box, second row on right. Green 13 D 22 Directed Digital Solutions HONDA4

23 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Acura RSX V White 3 (+) Ignition switch. Brown 7 B Starter Black/White 1 (+) Ignition switch. Brown 7 B Ignition Black/Yellow 6 (+) Ignition switch. Brown 7 B Accessory Black/Red 4 (+) Ignition switch. Brown 7 B F-CAN High N/A N/A N/A N/A N/A N/A N/A F- CAN Low N/A N/A N/A N/A N/A N/A N/A Immobilizer Data Red/Blue 2 Data Immobilizer connector. Green 7 A Security Light Blue/Orange 5 Cut Immobilizer connector. Green 7 A Keyless Data Blue/Orange 2 Data Rear of drivers fuse/relay box. Green 17 E Parking Lights Red/Yellow 15 (+) Drivers fuse/relay box. Green 18 F Ignition Interrupt Black/Yellow or Yellow 11 Cut OEM security module above driver kick. Black & White 20 G Drivers Door Trigger Green 20 (-) OEM security module above driver kick. Black & White 20 G Passenger Door Trigger Lt. Green/Red 9 (-) OEM security module above driver kick. Black & White 20 G Trunk/Hatch Trigger Red 7 (-) OEM security module above driver kick. Black & White 20 G Hood Trigger Green/Black 18 (-) OEM security module above driver kick. Black & White 20 G Tach Blue 5 AC Drivers fuse/relay box. Green 8 D Brake White/Black 3 (+) Drivers fuse/relay box. Green 13 D Honda Civic V White 3 (+) Ignition switch. Brown 7 B Starter Black/White 1 (+) Ignition switch. Brown 7 B Ignition Black/Yellow 6 (+) Ignition switch. Brown 7 B Accessory Black/Red 4 (+) Ignition switch. Brown 7 B F-CAN High N/A N/A N/A N/A N/A N/A N/A F- CAN Low N/A N/A N/A N/A N/A N/A N/A Immobilizer Data Red/Blue 2 Data Immobilizer connector. Green 7 A Security Light Blue/Orange 5 Cut Immobilizer connector. Green 7 A Keyless Data Blue/Orange 2 Data Rear of drivers fuse/relay box. Green 17 E Parking Lights Red/Yellow 15 (+) Drivers fuse/relay box. Green 18 F Ignition Interrupt Yellow 8 Cut OEM security module above driver kick. Green 16 G Drivers Door Trigger Green 3 (-) OEM security module above driver kick. Green 16 G Passenger Door Trigger Lt. Green/Red 2 (-) OEM security module above driver kick. Green 16 G Drivers Rear Door Trigger Passenger Rear Door Trigger Green/White 1 (-) OEM security module above driver kick. Green 16 G Trunk Trigger Blue/Yellow 4 (-) OEM security module above driver kick. Green 16 G Hood Trigger N/A N/A N/A N/A N/A N/A N/A Tach Blue 5 AC Drivers fuse/relay box. Green 8 D Brake White/Black 2 (+) Brake switch White 4 H 23 Directed Digital Solutions HONDA4

24 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Honda Civic Hybrid V White 3 (+) Ignition switch. Brown 7 B Starter Black/White 1 (+) Ignition switch. Brown 7 B Ignition Black/Yellow 6 (+) Ignition switch. Brown 7 B Accessory Black/Red 4 (+) Ignition switch. Brown 7 B F-CAN High N/A N/A N/A N/A N/A N/A N/A F- CAN Low N/A N/A N/A N/A N/A N/A N/A Immobilizer Data Red/Blue 2 Data Immobilizer connector. Green 7 A Security Light Blue/Orange 5 Cut Immobilizer connector. Green 7 A Keyless Data Blue/Orange 2 Data Rear of drivers fuse/relay box. Green 17 E Parking Lights Red/Yellow 15 (+) Drivers fuse/relay box. Green 18 F Ignition Interrupt Yellow 8 Cut OEM security module above driver kick. Green 16 G Drivers Door Trigger Green 3 (-) OEM security module above driver kick. Green 16 G Passenger Door Trigger Lt. Green/Red 2 (-) OEM security module above driver kick. Green 16 G Drivers Rear Door Trigger Passenger Rear Door Trigger Green/White 1 (-) OEM security module above driver kick. Green 16 G Trunk Trigger Blue/Yellow 4 (-) OEM security module above driver kick. Green 16 G Hood Trigger N/A N/A N/A N/A N/A N/A N/A Tach Blue 5 AC Drivers fuse/relay box. Green 8 D Brake White/Black 2 (+) Brake switch White 4 H Honda CR-V V White 3 (+) Ignition switch. Brown 7 B Starter Black/White 1 (+) Ignition switch. Brown 7 B Ignition Black/Yellow 6 (+) Ignition switch. Brown 7 B Accessory Black/Red 4 (+) Ignition switch. Brown 7 B F-CAN High N/A N/A N/A N/A N/A N/A N/A F- CAN Low N/A N/A N/A N/A N/A N/A N/A Immobilizer Data White 2 Data Immobilizer connector. Green 7 A Security Light Blue/Orange 5 Cut Immobilizer connector. Green 7 A Keyless Data Blue/Orange 2 Data Keyless Entry Module left of column. Green 5 I Parking Lights Red/Yellow 9 (+) Drivers fuse/relay box. Green 10 F Ignition Interrupt Yellow 15 Cut Factory alarm plug left of steering column. Green 22 G Drivers Door Trigger Green 3 (-) Factory alarm plug left of steering column. Green 22 G Passenger Door Trigger Drivers Rear Door Trigger Passenger Rear Door Trigger Trunk Trigger Lt. Green/Red Red 2 1 (-) (-) Factory alarm plug left of steering column. Factory alarm plug left of steering column. Green Green G G Hood Trigger Yellow/Red 5 (-) Factory alarm plug left of steering column. Green 22 G Trunk Release Black/Yellow 16 (-) Above drivers kick panel. Gray 22 G Tach Blue 5 AC Drivers fuse/relay box. Green 8 D Brake White/Black 2 (+) Brake switch White 4 H 24 Directed Digital Solutions HONDA4

25 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Honda Element V White 3 (+) Ignition switch. Brown 7 B Starter Black/White 1 (+) Ignition switch. Brown 7 B Ignition Black/Yellow 6 (+) Ignition switch. Brown 7 B Accessory Black/Red 4 (+) Ignition switch. Brown 7 B F-CAN High N/A N/A N/A N/A N/A N/A N/A F- CAN Low N/A N/A N/A N/A N/A N/A N/A Immobilizer Data White 2 Data Immobilizer connector. Green 7 A Security Light Blue/Orange 5 Cut Immobilizer connector. Green 7 A Keyless Data Blue/Orange 2 Data Drivers fuse/relay box. Green 17 E Parking Lights Red/Yellow 9 (+) Drivers fuse/relay box. Green 10 F Ignition Interrupt Yellow 15 Cut OEM security module above driver kick. Green 22 G Drivers Door Trigger Green 3 (-) OEM security module above driver kick. Green 22 G Passenger Door Trigger Gray/Black 2 (-) OEM security module above driver kick. Green 22 G Trunk/Hatch Trigger Red 1 (-) OEM security module above driver kick. Green 22 G Brake White/Black 2 (+) Brake switch White 4 H Tach Blue 5 AC Drivers fuse/relay box. Green 8 D Honda Element V White 3 (+) Ignition switch. Brown 7 B Starter Black/White 1 (+) Ignition switch. Brown 7 B Ignition Black/Yellow 6 (+) Ignition switch. Brown 7 B Accessory Black/Red 4 (+) Ignition switch. Brown 7 B F-CAN High White 6 Data OBDII. Gray 16 C F- CAN Low Red 14 Data OBDII. Gray 16 C Immobilizer Data White 2 Data Immobilizer connector. Green 7 A Security Light Blue/Orange 5 Cut Immobilizer connector. Green 7 A Keyless Data Blue/Orange 2 Data Drivers fuse/relay box. Green 17 E Parking Lights Red/Yellow 9 (+) Drivers fuse/relay box. Green 10 F Ignition Interrupt Yellow 15 Cut OEM security module above driver kick. Green 22 G Drivers Door Trigger Green 3 (-) OEM security module above driver kick. Green 22 G Passenger Door Trigger Gray/Black 2 (-) OEM security module above driver kick. Green 22 G Trunk/Hatch Trigger Red 1 (-) OEM security module above driver kick. Green 22 G Brake White/Black 2 (+) Brake switch White 4 H Tach Blue 5 AC Drivers fuse/relay box. Green 8 D 25 Directed Digital Solutions HONDA4

26 Type 5 with T-Harness (THHOC5) Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). OBDII Diagnostic (black conn. under driver side dash, connector side view) Ignition Switch (white or brown conn. and ignition cylinder) Immobilizer Connector (green conn. at ignition cylinder) F-CAN High: White, pin Keyless Data: Blue/Orange, pin 2 F-CAN Low: Red, pin 14 HS Can Low: Tan HS Can High: Tan/Black Keyless Data: Yellow/Black 16-pin Black Connector Remote Start Safety Override Switch THHOC5 (optional T-Harness) Keyless Receiver Unit (Green conn. left of drivers fuse box) The Remote Start Safety Override Switch MUST be in the ON position. Hood Pin Refer to the Vehicle wiring reference charts and for more information on wire and connector details. OR (-) Hood Input: Gray: 3 (AC) Tach Input: Violet/White: 6 (-) Door Input: White/Green: 10 (-) Trunk Input: Lt. Blue: 13 (+) Brake Input: Brown/White: 16 (+) Siren Output: Brown: pin White Connector White: (+) Parking Light Output Siren (+) Brake: White/Black, pin 4 (+) Parking Lights: Red/Black, pin Drivers Fuse/Relay Box (green conn. center of fuse relay) 26 Directed Digital Solutions HONDA4

27 Type 5 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). (+) Starter: pin 1 (+) Accessory 1: pin 4 (+) 12V: pin Ignition Switch (white or brown conn. at ignition cylinder) F-CAN High: White, pin F-CAN Low: Red, pin OBDII Diagnostic (black conn. under driver side dash, connector side view) Keyless Receiver Unit (Green conn. left of drivers fuse box) Keyless Data: Blue/Orange, pin 2 Cut (+) Accessory 2: pin 5 (+) Ignition: pin 6 (+) Starter Output (car side): Violet: 8 Starter Input (key side): Green: 7 (+) 12V Input: Red: 6 (+) Accessory 1 Output: Orange: 5 (+) 12V Input: Red: 4 (+) Ignition Input/Output: Pink: 3 (+) 12V Input: Red/White: 2 (+) Accessory 2 Output: Pink/White: 1 8 thick-gauge wires MC501 4 White 7 White Keyless Data: Yellow/Black: 2 Immobilizer Data: Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 Immobilizer conn. (green connector at ignition barrel) Immobilizer Data: pin 2 Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. Security Light: pin Hood Pin OR (-) Hood Input: Gray: 3 10: Red: (+) 12V Input Refer to the Vehicle wiring reference charts and for more information on wire and connector details. (AC) Tach Input: Violet/White: 6 (-) Door Input: White/Green: 10 (-) Trunk Input: Lt. Blue: 13 (+) Brake Input: Brown/White: 16 (+) Siren Output: Brown: 17 9: Black: (-) Ground 5: Orange/Red: Security Light Interrupt (conn. side) 4: Yellow/Red: Security Light Interrupt (veh. side) 2 & 8: White/Brown: (+) Parking Light Input Siren 1 & 7: White: (+) Parking Light Output (+) Brake: White/Black, pin 4 (+) Parking Lights: Red/Black, pin Drivers Fuse/Relay Box (green conn. center of fuse relay) 27 Directed Digital Solutions HONDA4

28 Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to for additional information. Wire Information Connector Information Function Color Pin Polarity Location Color Pins Ref. Honda Fit Immobilizer Data Lt. Green/Black 2 Data Immobilizer connector. Green 7 A Security Light Red/Black 5 Data Immobilizer connector. Green 7 A 12V White 3 (+) Ignition switch. White or Brown 7 B Starter Black/White 1 (+) Ignition switch. White or Brown 7 B Ignition Black/Yellow 6 (+) Ignition switch. White or Brown 7 B Accessory 1 Yellow/Black 4 (+) Ignition switch. White or Brown 7 B Accessory 2 White/Red 5 (+) Ignition switch. White or Brown 7 B F-CAN High White 6 Data OBDII. Gray 16 C F- CAN Low Red 14 Data OBDII. Gray 16 C Parking Lights Red/Black 5 (+) Drivers fuse/relay box. Green 14 D Brake White/Black 4 (+) Drivers fuse/relay box. Green 14 D Tach Green/Orange 2 AC Drivers fuse/relay box. Green 20 D Drivers Door Trigger Green 18 (-) OEM security module above driver kick. White 20 E Passenger Door Trigger Gray/Black 19 (-) OEM security module above driver kick. White 20 E Trunk/Hatch Trigger Green/Red 17 (-) OEM security module above driver kick. White 20 E Hood Trigger Green/Black 18 (-) OEM security module above driver kick. White 20 E Keyless Data Blue/Orange 2 Data Keyless receiver unit left of drivers fuse box. Green 5 F 28 Directed Digital Solutions HONDA4

29 Type 6 with T-Harness (THHOC5) Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). Parking Lights: Gray, pin (+) Brake: Lt. Green, pin Drivers Fuse/Relay Box (white conn. at fuse box) Drivers Fuse/Relay Box (green conn. at drivers fuse box) Ignition Switch (white or brown conn. and ignition cylinder) Immobilizer Connector (green conn. at ignition barrel) Single Wire CAN: pin 4 OBDII Diagnostic (black conn. under driver side dash, connector side view) F-CAN High: White, pin 6 Single Wire CAN: Lt. Green HS Can High: Tan/Black HS Can Low: Tan 16-pin Black Connector Remote Start Safety Override Switch THHOC5 (optional T-Harness) F-CAN Low: Red, pin 14 Refer to the Vehicle wiring reference charts and for more information on wire and connector details. 16 Hood Pin OR (-) Hood Input: Gray: 3 (AC) Tach Input: Violet/White: 6 (-) Trunk Release Output: Red/White: 9 (-) Door Input: White/Green: 10 (-) Trunk Input: Lt. Blue: 13 (+) Brake Input: Brown/White: 16 (+) Siren Output: Brown: 17 The Remote Start Safety Override Switch MUST be in the ON position. 12-pin White Connector Yellow: Ignition Interrupt (vehicle side) Orange/Yellow: Ignition Interrupt (conn. side) White: (+) Parking Light Output Cut Ignition: Red, pin Siren Keyless Access Control Unit (black conn. left of brake) 29 Directed Digital Solutions HONDA4

30 Type 6 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). Drivers Fuse/Relay Box (green conn. at drivers fuse box) Single Wire CAN: pin 4 (+) Brake: Lt. Green, pin Parking Lights: Gray, pin 31 Immobilizer Data: pin 2 Cut Security Light: pin Immobilizer conn. (green connector at ignition barrel) Ignition Switch (white or brown conn. at ignition cylinder) (+) Starter: pin 1 (+) Accessory: pin (+) 12V: pin 3 (+) Ignition: pin 6 (+) Starter Output (car side): Violet: 8 Starter Input (key side): Green: 7 (+) 12V Input: Red: 6 (+) Accessory Output: Orange: 5 (+) 12V Input: Red: 4 (+) Ignition Input/Output: Pink: 3 (+) Fused (30A) Ignition 2/ Flex Relay Input: Red/White: 2 (+) Ignition 2/Flex Relay Output: Pink/White: 1 OBDII Diagnostic (black conn. under driver side dash, connector side view) 8 thick-gauge wires MC501 4 White 7 White 1 9 Immobilizer Data: Orange/Black: 3 Drivers fuse/relay box (white conn. at fuse box) F-CAN High: White, pin F-CAN Low: Red, pin 14 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 Single Wire CAN: Lt. Green: 6 Cut Ignition: Red, pin Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. Keyless Access Control Unit (black conn. left of brake) Refer to the Vehicle wiring reference charts and for more information on wire and connector details. Hood Pin OR (-) Hood Input: Gray: 3 (AC) Tach Input: Violet/White: 6 (-) Trunk Release Output: Red/White: 9 (-) Door Input: White/Green: 10 (-) Trunk Input: Lt. Blue: 13 (+) Brake Input: Brown/White: 16 (+) Siren Output: Brown: 17 11: Orange/Yellow: Ignition Interrupt (conn. side) 10: Red: (+) 12V Input 9: Black: (-) Ground 6: Yellow: Ignition Interrupt (vehicle side) 5: Orange/Red: Security Light Interrupt (conn side) 4: Yellow/Red: Security Light Interrupt (vehicle side) 2 & 8: White/Brown: (+) Parking Light Input 1 & 7: White: (+) Parking Light Output Siren 30 Directed Digital Solutions HONDA4