Waterous S100 Single Stage Pump

Size: px
Start display at page:

Download "Waterous S100 Single Stage Pump"

Transcription

1

2 The S100 Series end suction fire pump provides versatility in a smaller package. With a capacity of 2000 GPM (7570 L/min), the S100 Features a dynamic yet compact design, incorporating a ductile iron body with either an aluminum transmission (C20 Series or PA Series) for midship mounting or an aluminum bearing housing for direct drive mounting (pedestal mount). This image is of the Quint being assembled at KME 350 gallon water tank Pump and plumbing have been installed The centrifugal pump is preferred by the fire protection service due to its ability to fully utilize any positive suction inlet pressure, reducing the amount of work done by the pump. For example, if the required discharge pressure is 120 PSI (8 BAR), and the inlet pressure is 45 PSI (3 BAR), the pump must only produce the difference in pressures of 75 PSI (5 BAR). This contributes to low engine and pump speeds with reduced maintenance. Decreased maintenance is aided by the fact a centrifugal pump has basically only two moving parts the impeller and the shaft. 103

3 Centrifugal Force A centrifugal pump operates on the principle that centrifugal force is created by a rapidly spinning disk. Figure 1-1 shows that an amount of water has been placed at the center of a disk. The disk is rotated at some speed, and the water is thrown from the center toward the outer circumference of the disk. The distance that the water travels from the center directly relates to the diameter of the disk and the speed of rotation. When water is confined in a closed container (such as the pump body), its pressure rises to a level that depends on the speed of rotation. There are three interrelated factors that regulate the performance of a centrifugal pump: Waterous S100 is a Single Stage Centrifugal Pump Overheating If the pump runs even for a few minutes completely closed it may heat the water enough to scald someone when the valve is opened. When operating the pump, at least one discharge valve should be open slightly to prevent the pump from overheating. Overheating can damage the packing, seals and other pump parts. SPEED (RPM). If the speed of rotation increases with flow held constant, the water pressure increases. PRESSURE. Pressure is usually measured in Pounds Per Square Inch (PSI) (BAR). If pressure changes with speed held constant, the flow (measured in GPM) (LPM) will change inversely, that is, if pressure increases, flow decreases. FLOW. Flow is usually measured in the number of gallons of water per minute (GPM) (LPM) that a pump can deliver when supplied from draft. If the pressure is held constant, the flow will increase with an increase in the speed of rotation. 104

4 Impeller The impeller provides velocity to the water. This part is mounted on a shaft that is rotated by the drive. Water enters the rotating impeller at the intake (or eye), and is confined by the shrouds and the vanes mounted in the impeller to build pressure. The vanes guide water from the inlet to the discharge and reduce the turbulence of the spinning water. Vanes curve away from the direction of rotation so water moves toward the outer edge. The shrouds form the sides of the impeller, and keep the water confined to centrifugal acceleration. Single stage impeller Centrifugal Force From a Rotating Disk This image is of the Waterous S100 main pump when installed on the Quint at KME Pump transmission The figure below traces a drop of water from the intake of the impeller to the discharge outlet. The impeller is mounted so that the discharging tube is widest at the pump outlet. The increasing discharge path, known as the volute, collects the water at a constant velocity. A further increase in pressure and a decrease in velocity take place in the diffuser. 105

5 Cavitation occurs when a centrifugal pump is attempting to discharge more water than it is receiving. When cavitation occurs, a vacuum is created near the eye of the impeller. As the vacuum increases, the boiling point of the water is lowered until it reaches a point near the impeller eye where it flashes into vapor and enters the impeller. Once the vapor pockets, or bubbles, enter the impeller, the process begins to reverse itself. As the vapor reaches the discharge side of the pump, it is subjected to a high positive pressure, which condenses the vapor back to a liquid. The sudden change from vapor pockets to a liquid generates a shock effect which causes a significant noise that is characteristic of cavitation. This shock damages the impeller and pump housing. This may happen while pumping from draft or a hydrant. The problem in either case is the pump running away from the supply and this causes a vacuum to occur. Signs of Cavitation 1. Sudden pressure or capacity loss. 2. Increasing pump speed without corresponding increase in volume or pressure. 3. Excessive pump vibration. 4. A rattling sound resembling gravel going through the pump. Reducing pump speed or improving intake conditions will usually eliminate cavitation. Cavitation is often referred to as the pump running away from the water supply. This means that the operator is trying to pump more water out of the pump than is going into the pump. To eliminate cavitation, the operator must be aware of the warning signs and correct the situation, or serious damage to the pump and impeller will occur. The most reliable indication that a pump is approaching cavitation is when an increase in engine RPM does not cause an increase in the pump discharge pressure. The operator must not depend entirely on the vacuum gage to indicate when a pump is nearing cavitation. This is because the vacuum gage is usually tapped into the intake chamber several inches away from the leading edge of the impeller eye where the greatest amount of vacuum occurs. The most common way to eliminate cavitation is to decrease the amount of water being discharged. This is accomplished by decreasing engine speed or closing discharge valves. This will allow pressure to increase but this will result in a reduction of flow. 106

6 The Waterous C20 transmission, with a high-strength aluminum case, transmits power from the truck's automatic transmission either to the fire pump or to the drive axle of the truck. This image is of the Waterous S100 main pump when installed on the Quint at KME Single Stage Impeller Waterous C20 Pump Transmission After the wheels the Main Pump is installed on the chassis and then the engine and driveline. Connection of Propeller Shaft (Driveline) Pump Pump Transmission Vehicle propeller shafts connected to pump transmission 107

7 Low or excessive lubrication fluid may cause damage. Lubrication fluid temperature should not exceed 250 degrees F for extended periods of time. If lubricant fluid level is low, locate source of leak and repair. If level is high, loosen oil level plug and drain until proper level is reached. If any water drains out, change lubrication fluid and determine source of water leakage and repair. Premature seal wear and damage will occur. 1. Check the lubrication fluid level monthly by checking the sight plug or by removing the oil level plug. The fluid should be level with the bottom of the oil level hole. 2. Change lubrication fluid and clean breather once a year or after each 100 hours of operation, whichever comes first. Lubrication fluid may be added through the oil level hole or by removing the breather and adding fluid through the opening. Any type of automatic transmission fluid (ATF) may be used. 3. Quantities of lubrication fluid if system is completely drained and refilled: C20 Transmissions: Approximately 8 quarts of ATF. Pump Transmission: The bearings and drive chain are lubricated by a splash and passive lubrication system. Lubrication is accomplished when spray from the chain collects in a reservoir in the top of the case. The lubricant flows out of the reservoir, through a hose and onto the inside surface of the chain. This ensures all pivoting components of the chain receive lubrication. An electronic tachometer connection protrudes from the tachometer housing at a 45 angle. This tachometer pick-up senses the drive shaft speed. 108

8 Engaging the Pump Transmission Pump Transmission cut away Shift fork has moved to the Pump Transmission side Road Gear Position The shift mechanism within the transmission consists of a sliding internally-toothed collar which is always in engagement with an externally-toothed section of the drive shaft. A fork shifts the collar either to engage it with teeth on the drive sprocket hub (PUMP) or to engage it with the teeth on the coupling shaft (ROAD). When in PUMP position, the shift collar transmits power from the drive shaft through the drive sprocket and the chain to the driven sprocket. The coupling shaft remains stationary. When in ROAD position, the shift collar transmits power directly from the drive shaft through the coupling shaft to the truck propeller shaft and drive axle(s). In this position, the pump drive and driven sprockets remain stationary while the drive shaft rotates. Three shift indicator lights are furnished. Two are mounted in the cab and the other is mounted on the operators panel. These lights indicate to the operators that the shift has been completed into PUMP position and the truck transmission is in pumping gear. 109

9 Manual Pump Transmission Shift Pump Pump Shaft Pump Gear Intermediate Gear Gearbox Tachometer Cable Connection Sliding Gear Input Shaft Shift Shaft Pull the shift shaft Out for Pump Position (after in-cab control valve selection), or push shift shaft for Road Position (after incab control valve selection). Shift Fork DO NOT ATTEMPT EMERGENCY SHIFT PROCEDURES WHILE THE ENGINE IS RUNNING. Employ manual override procedure at the shift cylinder on the pump gearbox as follows: An eyebolt is provided in the shift shaft to accept a drift punch or screwdriver. By inserting this tool into the hole provided, it will enable you to pull or push the shaft manually. Pull the shift shaft Out for Pump Position (after in-cab control valve selection), or push shift shaft for Road Position (after in-cab control valve selection). If the shift stroke cannot be completed manually, turn the driveshaft slightly by hand to realign the internal gears and repeat the manual shift effort. 110

C21 Series Transmission Operation and Maintenance Instructions

C21 Series Transmission Operation and Maintenance Instructions C21 Series Transmission Operation and Maintenance Instructions Read through the the operation instructions instructions carefully carefully before using before your using Waterous your Waterous Transmission.

More information

W & Y Series Split Shaft Transmission Operation & Maint.

W & Y Series Split Shaft Transmission Operation & Maint. W & Y Series Split-Shaft Chain Drive Transmission Operation and Maintenance Form No. F-1031 Section 2205.3 Issue Date 03/94 Rev. Date 06/24/13 Illustrations 1. Electric Shift Manual Override... 5 2. Pneumatic

More information

Operation and Maintenance. S100 Series Centrifugal Fire Pumps. Table of Contents. Visit us at F /22/02 6/21/18

Operation and Maintenance. S100 Series Centrifugal Fire Pumps. Table of Contents. Visit us at   F /22/02 6/21/18 S100 Series Centrifugal Fire Pumps Operation and Maintenance Form No. F-1031 Section 2117 Issue Date 02/22/02 Rev. Date 6/21/18 Table of Contents Safety Information-----------------------------------------------

More information

Table of Contents Illustrations

Table of Contents Illustrations Principals of Operation Inspection & Troubleshooting Principles of Operation Inspection & Troubleshooting Form No. F 1031 Section 1000 Issue Date 09/19/94 Rev. Date 02/07/07 Table of Contents Illustrations

More information

HL Series Centrifugal Fire Pumps Operation and Maintenance Instructions

HL Series Centrifugal Fire Pumps Operation and Maintenance Instructions HL Series Centrifugal Fire Pumps Operation and Maintenance Instructions Table of Contents Read through the safety information and operating instructions carefully before using your Waterous HL Series Fire

More information

K, T, TK, TA and KC Series Operation and Maintenance Instructions

K, T, TK, TA and KC Series Operation and Maintenance Instructions K, T, TK, TA and KC Series Operation and Maintenance Instructions Table of Contents Introduction... 1 General Description for K, T, TK & TA Series... 1 K Series Transmission........................................

More information

ESCONDIDO FIRE DEPT TRAINING MANUAL Section DRIVER OPERATOR Page 1 of 13 Pumps and Accessory Equipment Revised

ESCONDIDO FIRE DEPT TRAINING MANUAL Section DRIVER OPERATOR Page 1 of 13 Pumps and Accessory Equipment Revised DRIVER OPERATOR Page 1 of 13 PUMPS AND ACCESSORY EQUIPMENT Pumps are designed for many different purposes. In order to understand the proper application and operation of a pump in a given situation, firefighters

More information

S200-P Series Centrifugal Fire Pumps Operation and Maintenance Instructions

S200-P Series Centrifugal Fire Pumps Operation and Maintenance Instructions S200-P Series Centrifugal Fire Pumps Operation and Maintenance Instructions Table of Contents Read through the safety information and operating instructions carefully before using your S200-P Series Fire

More information

With PA Series Transmission: S101 Series Midship Pumps: With C20 Series Transmission:

With PA Series Transmission: S101 Series Midship Pumps: With C20 Series Transmission: S100 Series C10 Chain Drive Transmission Overhaul Instructions Installation Instructions S100 Series Centrifugal Fire Pumps Issue Date Form No. F 1031 Section 3017 09/25/02 Rev. Date 04/26/13 IL3292 Table

More information

S200-G Series Centrifugal Fire Pumps Operation and Maintenance Instructions

S200-G Series Centrifugal Fire Pumps Operation and Maintenance Instructions by Waterous S200-G Series Centrifugal Fire Pumps Operation and Maintenance Instructions Table of Contents IL3771 Read through the safety information and operating instructions carefully before using your

More information

Describe the function of a hydraulic power unit

Describe the function of a hydraulic power unit Chapter 7 Source of Hydraulic Power Power Units and Pumps 1 Objectives Describe the function of a hydraulic power unit and identify its primary components. Explain the purpose of a pump in a hydraulic

More information

Al- Ameen Engg. College. Fluid Machines. Prepared by: AREEF A AP/ ME AL AMEEN ENGINEERING COLLEGE Shoranur.

Al- Ameen Engg. College. Fluid Machines. Prepared by: AREEF A AP/ ME AL AMEEN ENGINEERING COLLEGE Shoranur. Fluid Machines Prepared by: AREEF A AP/ ME AL AMEEN ENGINEERING COLLEGE Shoranur Classification of hydraulic machines HYDROULIC MACHINES (I) Hydraulic Turbines A hydraulic machine which converts hydraulic

More information

Superior Performance

Superior Performance QMAX MIDSHIP PUMP Superior Performance QMAX Superior Performance The Qmax single stage mid-ship pump generates NFPA 1901 rated flows up to 2,250 GPM (8,515 LPM) from draft True 2,000 GPM rated pump body

More information

HL Series Centrifugal Fire Pumps Installation Instructions

HL Series Centrifugal Fire Pumps Installation Instructions HL Series Centrifugal Fire Pumps Installation Instructions Table of Contents Read through the installation instructions carefully before installing your Waterous HL Series Fire Pump. Introduction...................................................

More information

With WB Series Transmission: With PA Series Transmission: With K Series Transmission:

With WB Series Transmission: With PA Series Transmission: With K Series Transmission: Fire Pumps CG Series Centrifugal Fire Pumps Installation Instructions IL3214 Table of Contents Safety Information... 2 Introduction... 3 Pump Mounting: CGVG Series Pumps: With C20 Series Transmission:

More information

Operation and Maintenance. CS Series Centrifugal Fire Pumps. Table of Contents. Visit us at F /14/95

Operation and Maintenance. CS Series Centrifugal Fire Pumps. Table of Contents. Visit us at  F /14/95 CS Series Centrifugal Fire Pumps Operation and Maintenance Form No. F-1031 Section 2115 Issue Date 12/14/95 Rev. Date 3/16/17 Table of Contents Read through the safety information and operating instructions

More information

Lecture 6. Systems review exercise To be posted this weekend Due next Friday (3/6)

Lecture 6. Systems review exercise To be posted this weekend Due next Friday (3/6) 150 Systems review exercise To be posted this weekend Due next Friday (3/6) Lecture 6 Coming week: Lab 13: Hydraulic Power Steering Lab 14: Integrated Lab (Hydraulic test bench) Topics today: Pumps and

More information

CL Series Centrifugal Fire Pumps Installation Instructions

CL Series Centrifugal Fire Pumps Installation Instructions CL Series Centrifugal Fire Pumps Installation Instructions Table of Contents Safety Information... 1 Introduction... 2 Pump Mounting... 2 Pump Mounting-CLK Series (Optional Mounting Brackets) 3 Optional

More information

Ledwell Water Trucks. Discount Equipment 1014 South Congress Ave. West Palm Beach, FL (ext 106) (Toll Free)

Ledwell Water Trucks. Discount Equipment 1014 South Congress Ave. West Palm Beach, FL (ext 106) (Toll Free) Ledwell Water Trucks Discount Equipment 1014 South Congress Ave. West Palm Beach, FL 33406 561-964-4949 (ext 106) 877-690-3101 (Toll Free) When loading or unloading, be aware of any overhead obstructions

More information

Operation and Maintenance. CG Series Centrifugal Fire Pumps. Illustrations

Operation and Maintenance. CG Series Centrifugal Fire Pumps. Illustrations CG Series Centrifugal Fire Pumps Operation and Maintenance Form No. F 1031 Section 2102.2 Issue Date 04/28/95 Rev. Date 3/20/17 Illustrations IL 1932 1. CGVG Series Pump... 4 2. CGR Series Pump........................

More information

AS Centrifugal Pump Exploded View

AS Centrifugal Pump Exploded View AS-200 2 Centrifugal Pump Exploded View (5278949) AS-200 (5278949) Dimensions Page 3 OWNER S MANUAL Parts & Instruction Manual Centrifugal Pumps AS-300 (5278333) AS-200 (5278949) General Information Thank

More information

CHASSIS. Transmission Type 1st nd rd th Gear Ratio

CHASSIS. Transmission Type 1st nd rd th Gear Ratio CH-2 CHASSIS AA80E AUTOMATIC TRANSMISSION DESCRIPTION An AA80E automatic transmission is used. This automatic transmission is a compact, lightweight and high-capacity 8-speed sport direct shift gearbox.

More information

Model 133 Models 134 & 135 AURORA 130 SERIES SINGLE STAGE TURBINE TYPE PUMPS

Model 133 Models 134 & 135 AURORA 130 SERIES SINGLE STAGE TURBINE TYPE PUMPS Model Models 4 & AURORA 0 SERIES SINGLE STAGE TURBINE TYPE PUMPS WWW.AURORAPUMP.COM AURORA 0 SERIES Single Stage Turbine Type Pumps Capacities to 0 G.P.M. Heads to 700 Ft. Temperatures to F A Pioneer in

More information

Automatic Recirculation Valves One Step Centrifugal Pump Minimum Flow Protection

Automatic Recirculation Valves One Step Centrifugal Pump Minimum Flow Protection Automatic Recirculation s One Step Centrifugal Pump Minimum Flow Protection HPM Series ENGINEERINGInc. Portage Avenue, Three Rivers, MI USA Phone: -7- Fax: -78-7 Centrifugal Pumps Require Protection If

More information

HIGH VELOCITY PUMP PUMP END

HIGH VELOCITY PUMP PUMP END HIGH VELOCITY PUMP USFP pumps are designed for firefighting and high volume water supply in industrial, oil and gas, nuclear, municipal, and marine applications. The USFP High Velocity Pump is designed

More information

Priming Systems Installation Instructions

Priming Systems Installation Instructions Priming Systems Installation Instructions System Components: Single Priming Pump: Single VAP Valve Systems: Control Panel Activated... 2 Auto Prime (Pressure Switch) Activated... 3 Multiple VAP Valve Systems...

More information

Marine Engineering Exam Resource Review of Hydraulics

Marine Engineering Exam Resource Review of Hydraulics 1. What is Pascal s law? Pressure confined on a confined fluid will transmit the pressure in all directions and act with equal force on all areas at right angles. 2. How does the law pertain to hydraulics?

More information

SPECIFY THE RIGHT HOT OIL PUMP FOR YOUR APPLICATION

SPECIFY THE RIGHT HOT OIL PUMP FOR YOUR APPLICATION SPECIFY THE RIGHT HOT OIL PUMP FOR YOUR APPLICATION Hot oil pumps are used in a range of industries, with their main user being the heat transfer oil customer. Often, oil temperatures will exceed 500 F

More information

High Rise Fire Pumps CM/CGV Series, CMU/CGV Series. Operation and Maintenance

High Rise Fire Pumps CM/CGV Series, CMU/CGV Series. Operation and Maintenance High Rise Fire Pumps CM/CGV Series, CMU/CGV Series Operation and Maintenance Form No. F-1031 Section 2110 Issue Date 10/92 Rev. Date 3/21/17 Table of Contents Safety Information... 1, 2 Introduction...

More information

Main Fire Pump Engagement. Shifting Into Pump 2006 / 2007 KME

Main Fire Pump Engagement. Shifting Into Pump 2006 / 2007 KME Main Fire Pump Engagement Shifting Into Pump 2006 / 2007 KME 1 Battery Switch Ensure battery switch is turned on to BOTH. 2 Ensure Maxi (Parking) Brake Set Maxi (Parking) Brake must be set or the Pump

More information

Module 1: Introduction to Drive Trains

Module 1: Introduction to Drive Trains Introduction ÂÂ Basic Components of a Drive Train Operation of a Drive Train Working Applications Types of Drives Types of Gears Formula for Calculating Gear Ratio Determining Gear Rotation Introduction

More information

GENESIS COUPE(BK) > 2010 > G 3.8 DOHC > Steering System

GENESIS COUPE(BK) > 2010 > G 3.8 DOHC > Steering System GENESIS COUPE(BK) > 2010 > G 3.8 DOHC > Steering System Steering System > General Information > Specifications Specifications Steering gear Oil pump Steering angle Power steering oil Item Specification

More information

NECO Pumping Systems

NECO Pumping Systems INSTALLATION OPERATION & MAINTENANCE INSTRUCTIONS For Your NECO Pumping Systems Fuel Oil Transfer System THIS COMPLETELY ASSEMBLED, TESTED, PACKAGED SYSTEM IS OF THE HIGHEST QUALITY AND DESIGN. TO OBTAIN

More information

GENUINE MEGA MEGA WATER PUMPS. 2-1

GENUINE MEGA MEGA WATER PUMPS.  2-1 GENUINE MEGA MEGA WATER PUMPS No pump, no spray. It s that simple. Mega water pumps are not off-the-shelf irrigation pumps designed to run sprinklers; they are the product of over 35 years of experience

More information

SP SERIES SELF-PRIMING MAG DRIVE

SP SERIES SELF-PRIMING MAG DRIVE SP SERIES SELF-PRIMING MAG DRIVE spend less time waiting. and more time pumping. year Big on power yet short on energy consumption, the SP Series from Finish Thompson is one of the most versatile and economical

More information

Water Treatment Plant Maintenance Considerations. Operation and Maintenance. Types of Maintenance 5/1/15

Water Treatment Plant Maintenance Considerations. Operation and Maintenance. Types of Maintenance 5/1/15 Water Treatment Plant Maintenance 1 Operation and Maintenance Purpose of O&M maintain design functionality (capacity) restore the system components to their original condition and thus functionality. Effective

More information

Module 7: Cooling System Components

Module 7: Cooling System Components  Â  Basic Cooling System Components Radiators Common Types of Radiators Coolant Hoses Water Pumps Centrifugal Force Types of Drives for Water Pumps Types of Drive Belts Basic Cooling System Components

More information

Overhaul Instructions. S100 Series Centrifugal Fire Pumps. Table of Contents F /22/02 1/19/18

Overhaul Instructions. S100 Series Centrifugal Fire Pumps. Table of Contents F /22/02 1/19/18 S100 Series Centrifugal Fire Pumps Overhaul Instructions Form No. F-1031 Section 4219 Issue Date 02/22/02 Rev. Date 1/19/18 Table of Contents Section Page Introduction 4 Ordering Repair Parts 4 Pump Models

More information

Service Manual #67. Installation and Service Instructions 6000, 7000 & 8000 Series Magnetically Coupled Pumps

Service Manual #67. Installation and Service Instructions 6000, 7000 & 8000 Series Magnetically Coupled Pumps Service Manual #67 Installation and Service Instructions 6000, 7000 & 8000 Series Magnetically Coupled Pumps Table of Contents Section Description Page 1 General Description 4 2 The Pumping Principle 5

More information

Principals of Operation... 1 Rotary Vane Priming Pump VPE and VPES... 2 Rotary Vane Priming Pump VPO and VPOS Priming Valve...

Principals of Operation... 1 Rotary Vane Priming Pump VPE and VPES... 2 Rotary Vane Priming Pump VPO and VPOS Priming Valve... Priming Systems Installation Priming Systems Operation & Maintenance Form No. F 1031 Section 2312 Issue Date 10/07/94 Rev. Date 02/27/06 Table of Contents Illustrations Principals of Operation...........................

More information

Max IV Rear Axle Replacement For models after Serial Number and all rear splined axle replacements.

Max IV Rear Axle Replacement For models after Serial Number and all rear splined axle replacements. Max IV Rear Axle Replacement For models after Serial Number 19089 and all rear splined axle replacements. 10/8/03 Max IV Snap Ring Rear Axle replacement.doc Tools required: 9/16 Wrench 6 Extension Steel

More information

Lecture 6. Systems review exercise To be posted this afternoon Due in class (10/23/15)

Lecture 6. Systems review exercise To be posted this afternoon Due in class (10/23/15) 153 Systems review exercise To be posted this afternoon Due in class (10/23/15) Lecture 6 Coming week: Lab 13: Hydraulic Power Steering Lab 14: Integrated Lab (Hydraulic test bench) Topics today: 2 min

More information

CP-1, CP-2, CP-2L & CPD-2 Series Overhaul

CP-1, CP-2, CP-2L & CPD-2 Series Overhaul CP-1, CP-2, CP-2L, CPD-2, E301-A and E302-A Series Fire Pumps Overhaul Instructions Form No. F-1031 Section 4205.1 Issue Date 02/88 Rev. Date 01/18/08 Table of Contents Safety Information.................................

More information

Troubleshooting the Transmission Hydraulic System

Troubleshooting the Transmission Hydraulic System Testing and Adjusting IT28F INTEGRATED TOOLCARRIER POWER TRAIN Testing And Adjusting Introduction Reference: For Specifications with illustrations, refer to SENR5974, IT28F Integrated Toolcarrier Power

More information

Automatic drain valves

Automatic drain valves driving commercial vehicles If you notice more than a few drops of water when you drain the supply reservoir, the air dryer or compressor may need servicing. fast fact Even if the air brake system includes

More information

Dry installed end-suction pumps, LSN-series. according to ISO 2858 / ISO 5199

Dry installed end-suction pumps, LSN-series. according to ISO 2858 / ISO 5199 Dry installed end-suction pumps, LSN-series according to ISO 2858 / ISO 5199 Technical characteristics Performance 50 Hz 60 Hz Capacity up to 600 m 3 /h 2900 USgpm Head up to 170 m 800 feet Speed up to

More information

Centrifugal Pumps (Part Nos. PS2SS PS73SS) PS2SS

Centrifugal Pumps (Part Nos. PS2SS PS73SS) PS2SS Centrifugal Pumps (Part Nos. PS2SS PS73SS) PS2SS Part No. Serial Number Date Purchased Table of Contents Page Safety Messages...2 Pump Curves...2 Pump End Assembly...3 Disassembly...3 Installation...4

More information

Topic 1. Basics of Oil Hydraulic Systems

Topic 1. Basics of Oil Hydraulic Systems Topic 1. Basics of Oil Hydraulic Systems Fluid power Fluid power is the technology that deals with the generation, control and transmission of forces and movement of mechanical element or system with the

More information

32 quarts Transmission Allison HT 740 Automatic Fluid

32 quarts Transmission Allison HT 740 Automatic Fluid BOOK: Blue Book I SECTION: E-One Engine (SGT) Page 1 of 6 E-ONE CYCLONE TABLE OF CONTENTS SPECIFICATIONS... 2 DAILY CHECKS... 2 SAFETY CHECKS... 3 START ENGINE... 3 STOP ENGINE... 3 EMERGENCY SHUTDOWN

More information

Definitions of Technical Terms

Definitions of Technical Terms Definitions of Technical Terms ABSOLUTE A measure having as it s zero point of base the complete absence of the entity being measured. ABSOLUTE PRESSURE A pressure scale with zero point at a perfect vacuum.

More information

Compressor Noise Control

Compressor Noise Control Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 1972 Compressor Noise Control G. M. Diehl Ingersoll-Rand Research Follow this and additional

More information

TC20 Chain Driven Power Take-Off Overhaul Instructions

TC20 Chain Driven Power Take-Off Overhaul Instructions TC20 Chain Driven Power Take-Off Overhaul Instructions Table of Contents Section Page Introduction 4 Ordering Repair Parts 4 General Information 5 Special Tools 6 Disassembly See Page 2 Reassembly See

More information

Bulletin C Dean Pump Division. Heavy Duty, High Temperature Process Pumps. R4140 Telescoping Guard. R4140 C-Face Motor Support

Bulletin C Dean Pump Division. Heavy Duty, High Temperature Process Pumps. R4140 Telescoping Guard. R4140 C-Face Motor Support Bulletin C 1.4.43 Dean Pump Division Heavy Duty, High Temperature Process Pumps R4140 Telescoping Guard R4140 C-Face Motor Support Dean Pump Series R Centrifugal Process Pumps Capacities to 5000 GPM (1135

More information

LIQUEFIED GAS PUMP INSTALLATION

LIQUEFIED GAS PUMP INSTALLATION LIQUEFIED GAS PUMP INSTALLATION Z400C ENGINEERING DATA AND DESIGN HANDBOOK THE APPLICATION OF PUMPS TO LIQUEFIED GAS TRANSFER Although we cannot change the nature of the liquefied gas, there are many things

More information

Powerstroke EGR Delete A B C

Powerstroke EGR Delete A B C 20-203 6.7 Powerstroke EGR Delete A B C D E F G H I J K Part # A B C D E F G H I J K PACKING LIST: QTY. 3 5 2 Description Sensor Bracket Exhaust Blockoff Plate Straights Barbed Brass Fitting 39 5/8 Coolant

More information

OPERATION & MAINTENANCE INSTRUCTIONS MODEL: TC-300

OPERATION & MAINTENANCE INSTRUCTIONS MODEL: TC-300 1-800-223-4540 ** 602-437-5020 OPERATION & MAINTENANCE INSTRUCTIONS MODEL: TC-300 READ INSTRUCTIONS THOROUGHLY BEFORE OPERATING MACHINE Contents Safety Instructions Pg 3 Operating Instructions Pg 4-5 (Light

More information

Sealless Magnetic Coupled Multistage Centrifugal Pumps with Priming Stage Type HZSM / HZSMB / HZSMR / HZSMA / HZSMAR

Sealless Magnetic Coupled Multistage Centrifugal Pumps with Priming Stage Type HZSM / HZSMB / HZSMR / HZSMA / HZSMAR Sealless Magnetic Coupled Multistage Centrifugal Pumps with Priming Stage Type HZSM / HZSMB / HZSMR / HZSMA / HZSMAR our contribution for environmental protection General DICKOW-pumps of series HZSM are

More information

our contribution for Sealless Magnetic Coupled Multistage Centrifugal Pumps Type HZM / HZMR / HZMB environmental protection

our contribution for Sealless Magnetic Coupled Multistage Centrifugal Pumps Type HZM / HZMR / HZMB environmental protection Sealless Magnetic Coupled Multistage Centrifugal Pumps Type HZM / HZMR / HZMB our contribution for environmental protection General DICKOW-pumps of series HZM are sealless multistage horizontal centrifugal

More information

Pyrolance, LLC SPECIFICATIONS FOR DIESEL ENGINE DRIVEN ULTRA HIGH PRESSURE PIERCING AND FIRE FIGHTING SYSTEM L 1000 W-D

Pyrolance, LLC SPECIFICATIONS FOR DIESEL ENGINE DRIVEN ULTRA HIGH PRESSURE PIERCING AND FIRE FIGHTING SYSTEM L 1000 W-D SPECIFICATIONS FOR DIESEL ENGINE DRIVEN ULTRA HIGH PRESSURE PIERCING AND FIRE FIGHTING SYSTEM L 1000 W-D 1 SPECIFICATIONS FOR FIRE FIGHTING SYSTEM FIRE FIGHTING AND PIERCING SPECIFICATIONS Scope and General

More information

LACT MEASUREMENT. Total Head = Or PSI = S.G. 2.31

LACT MEASUREMENT. Total Head = Or PSI = S.G. 2.31 LACT MEASUREMENT Prepared By: Ken A. Steward. P.E. Linco-Electromatic, Inc. 4580 West Wall Street Midland, Texas 79703 The Operation of L.A.C.T. Units The simplest approach to the understanding of the

More information

Routine Compressor Maintenance

Routine Compressor Maintenance Establishing a regular, well-organized maintenance program and strictly following it is critical to maintaining the performance of a compressed air system. One person should be given the responsibility

More information

1/2" AIR DRIVEN DIAPHRAGM PUMP

1/2 AIR DRIVEN DIAPHRAGM PUMP 1/2" DRIVEN DIAPHRAGM PUMP OPERATION AND SERVICE GUIDE O-1225D NOV. 2008 Page 1 of 6 Refer to Bulletin P-605, Parts List P-9151 DRIVEN, DOUBLE DIAPHRAGM PUMP MANUAL Congratulations on purchasing one of

More information

MICRO RAIN 50,58,&63 SPARE PARTS MANUAL JANUARY 1, 2005

MICRO RAIN 50,58,&63 SPARE PARTS MANUAL JANUARY 1, 2005 MICRO RAIN 50,58,&63 SPARE PARTS MANUAL JANUARY 1, 2005 Sheilding, Wheel Assys, Front Hitch Assy. Shielding,Wheel Assys, Front Hitch Assy. Ref. Part # Description Qty. 1 MR-88052112/8 Outer Chain Cover

More information

HORSTMAN GREASED LIGHTNING CLUTCH

HORSTMAN GREASED LIGHTNING CLUTCH HORSTMAN GREASED LIGHTNING CLUTCH Horstman s Greased Lightning (GL) clutch is designed for ultra high performance, and requires expert setup and a serious commitment to maintenance. Warning!!! 1. Clutch

More information

20EVP-A SERIES. Vertical In-Line Self-Priming Centrifugal Pumps for Petroleums and Solvents. Marlow Pumps. Marlow Pumps.

20EVP-A SERIES. Vertical In-Line Self-Priming Centrifugal Pumps for Petroleums and Solvents. Marlow Pumps. Marlow Pumps. 2EVP-A SERIES Vertical In-Line Self-Priming Centrifugal Pumps for Petroleums and Solvents PUMP: Heavy-duty cast iron construction, with 2 NPT female threaded, in-line suction and discharge ports. This

More information

TYPE PC Propeller Condensate Pumps

TYPE PC Propeller Condensate Pumps SHIPPENSBURG PUMP CO. INC. P.O. BOX 279, SHIPPENSBURG, PA 17257 PH 717-532-7321 FAX 717-532-7704 WWW.SHIPCOPUMPS.COM BULLETIN 103 Revised 8/17 TYPE PC Propeller Condensate Pumps with Cast Iron Receivers

More information

Quality Value Assurance

Quality Value Assurance Pump Selection Guide Quality Value Assurance In the beginning From it s inception in 1990 with one man in a service van, to the industry leader in innovative dairy solutions that DariTech is today, we

More information

BRAKE E

BRAKE E 8-1 GENERAL...8-2 SPECIFICATIONS...8-6 COMPONENTS...8-7 FRONT BRAKE...8-12 DISASSEMBLY INSPECTION REASSEMBLY (Pn1, Cu2 3 TON SERIES)...8-12 DISASSEMBLY INSPECTION REASSEMBLY (Pn2 3 TON SERIES)...8-17 BRAKE

More information

Mud Pump Condition Monitoring and Pulsation Control Equipment Technology. IADC Maintenance Committee Meeting

Mud Pump Condition Monitoring and Pulsation Control Equipment Technology. IADC Maintenance Committee Meeting Mud Pump Condition Monitoring and Pulsation Control Equipment Technology IADC Maintenance Committee Meeting 2008-10-08 IADC Presentation Optimization of the mud pump system performance through pump condition

More information

our contribution for Sealless Magnetic Coupled Multistage Centrifugal Pumps Type HZM / HZMR / HZMB environmental protection

our contribution for Sealless Magnetic Coupled Multistage Centrifugal Pumps Type HZM / HZMR / HZMB environmental protection Sealless Magnetic Coupled Multistage Centrifugal Pumps Type HZM / HZMR / HZMB our contribution for environmental protection General DICKOW-pumps of series HZM are sealless multistage horizontal centrifugal

More information

ABS Dry Installed Waste Water Pumps Series FR

ABS Dry Installed Waste Water Pumps Series FR A Operating Instruction 3 ABS Dry Installed Waste Water Pumps Series FR Shaft Seal Close-coupled and Bearing Assemblies 3R, 4R, 5R, 5F and 6F! Observe for hazardous liquids that there can be liquid left

More information

Wilfley. Model. Technical Handbook. Centrifugal Slurry Pump

Wilfley. Model. Technical Handbook. Centrifugal Slurry Pump Wilfley Technical Handbook Centrifugal Slurry Pump Model K Wilfley Model K Pumps A Slurry Pump for the Most Abrasive Slurries Single stage Side suction Horizontal To " discharge Sealess Design The Wilfley

More information

Vickers 45. VMQ Series 30 Vane Pumps. Fixed Displacement, For Industrial and Mobile Applications (4.188)

Vickers 45. VMQ Series 30 Vane Pumps. Fixed Displacement, For Industrial and Mobile Applications (4.188) [ (4.188) 49,4 (1.94) /21,8 /.86) 174,7/172,3 (6.88/6.78) 332,9/33,5 (13.11/13.1) "M" is marked if metric port threads No marking if inch port threads AS-568-152 O-ring Vickers 45 65,3 (2.57) 13 (5.1 VMQ

More information

BORG WARNER TRANSFER BOX

BORG WARNER TRANSFER BOX BORG WARNER TRANSFER BOX Overhaul Manual BORG WARNER 44-62 TRANSFER BOX OVERHAUL MANUAL This transfer box is used on the following models: New Range Rover Published by Rover Technical Communication 1996

More information

A pump is a machine used to move liquid through a piping system and to raise the pressure of the liquid.

A pump is a machine used to move liquid through a piping system and to raise the pressure of the liquid. What is a pump A pump is a machine used to move liquid through a piping system and to raise the pressure of the liquid. Why increase a liquid s pressure? Static elevation a liquid s pressure must be increased

More information

L-l0 Cumins Turbo charged engine needs five minute cool down at idle speed. Wisconsin engine needs five minute cool down at idle speed

L-l0 Cumins Turbo charged engine needs five minute cool down at idle speed. Wisconsin engine needs five minute cool down at idle speed BOOK: Blue Book I SECTION: Ford LTS 9000 Tanker (SGT) Page 1 of 10 TABLE OF CONTENTS FORD LTS 9000 2,500 GALLON TANKER SPECIFICATIONS... 2 IN THE CAB... 3 ON THE CONSOLE... 3 WISCONSIN AUXILIARY PUMP...

More information

RS Multi-Stage, Ring Section Pumps

RS Multi-Stage, Ring Section Pumps RS Multi-Stage, Ring Section Pumps Technical Specification Pages This page left intentionally blank. 1.0 Overview. The RS Series is Carver s multi-stage pump for fluids at moderate to high pressures. The

More information

INSULATED TELESCOPING AERIAL DEVICE SPECIFICATIONS Van Mounted 31July2002

INSULATED TELESCOPING AERIAL DEVICE SPECIFICATIONS Van Mounted 31July2002 INSULATED TELESCOPING AERIAL DEVICE SPECIFICATIONS Van Mounted 31July2002 It is the intent of the following specifications to set minimum requirements for an INSULATED 29 foot bottom of platform, 34 foot

More information

4 Tri-Seal Disassembly Instructions

4 Tri-Seal Disassembly Instructions 4 Tri-Seal Disassembly Instructions 1. Remove the cable guard and suction screen from the pump. Unbolt the pump end from the motor. 3. Remove the rotating assembly from the pump shell. Ensure that all

More information

3" & 4" Cast Iron Self-Priming Centrifugal Pump Instruction Manual

3 & 4 Cast Iron Self-Priming Centrifugal Pump Instruction Manual 12 3" & 4" Cast Iron Self-Priming Centrifugal Pump Instruction Manual 333 & 444 Series Read these instructions and the instructions covering operation of the pump drive unit. Do not operate the gas engine

More information

Low Profile J Series Power Unit with Vane Pump

Low Profile J Series Power Unit with Vane Pump Low Profile J Series Power Unit with Vane Pump READ ALL INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING

More information

2014 RAM C/V Tradesman

2014 RAM C/V Tradesman Fig. 91: Suction Hose Ball Valve NOTE: View typical 14. Open the suction hose's ball valve to begin refilling the cooling system. 15. When the vacuum gauge reads zero, the system is filled. NOTE: On some

More information

GH-BETTIS OPERATING & MAINTENANCE INSTRUCTIONS DISASSEMBLY & ASSEMBLY FOR THE T80X-M4-S DOUBLE ACTING SERIES HYDRAULIC ACTUATORS

GH-BETTIS OPERATING & MAINTENANCE INSTRUCTIONS DISASSEMBLY & ASSEMBLY FOR THE T80X-M4-S DOUBLE ACTING SERIES HYDRAULIC ACTUATORS GH-BETTIS OPERATING & MAINTENANCE INSTRUCTIONS DISASSEMBLY & ASSEMBLY FOR THE T80X-M4-S DOUBLE ACTING SERIES HYDRAULIC ACTUATORS -S INDICATES CYLINDERS ARE IN TANDEM PART NUMBER: 100121 REVISION "A" ECN

More information

FRONT WHEEL AND BRAKE DISCS. Order Job/Part Q ty Remarks Removing the front wheel and brake discs NOTE:

FRONT WHEEL AND BRAKE DISCS. Order Job/Part Q ty Remarks Removing the front wheel and brake discs NOTE: FRONT WHEEL AND BRAKE DISCS EAS00514 SIS FRONT WHEEL AND BRAKE DISCS 1 2 3 4 Order Job/Part Q ty Remarks Removing the front wheel and brake discs Remove the parts in the order listed. Place the motorcycle

More information

26 - COOLING SYSTEM CONTENTS ENGINE COOLING - DESCRIPTION... 3 ENGINE COOLING - OPERATION... 9 COOLING SYSTEM FAULTS... 1

26 - COOLING SYSTEM CONTENTS ENGINE COOLING - DESCRIPTION... 3 ENGINE COOLING - OPERATION... 9 COOLING SYSTEM FAULTS... 1 26 - COOLING SYSTEM CONTENTS Page LAND ROVER V8 DESCRIPTION AND OPERATION ENGINE COOLING - DESCRIPTION... 3 ENGINE COOLING - OPERATION... 9 FAULT DIAGNOSIS COOLING SYSTEM FAULTS... 1 REPAIR COOLANT - DRAIN

More information

HYDRAULIC SYSTEM, ISL-07

HYDRAULIC SYSTEM, ISL-07 SECTION 09-304.295 09-304.295/ 1 GENERAL DESCRIPTION 7 1 This system uses hydraulic power to operate a fan that forces outside air into the radiator located on the left-hand side at the rear of the bus.

More information

KONE EcoMod Escalator Repair Instructions

KONE EcoMod Escalator Repair Instructions 3.3 Replace drive motor NOTE! When moving the step band during the following procedures, always run the escalator on inspection (use hand held pendant control). 3.3.1 Remove drive motor Complete the following

More information

C E N T R I F U G A L P U M P S

C E N T R I F U G A L P U M P S C E T R I F U G A L P U M P S Kpro Slurry Pump Kpro Heavy Duty Slurry Pump A slurry pump for the most abrasive slurries Single stage Side suction Horizontal To 8 (200mm) discharge Sealess Design The Wilfley

More information

WARCO CHEMAG SERIES GH FILTERS

WARCO CHEMAG SERIES GH FILTERS WARCO CHEMAG SERIES GH FILTERS High Performance Pleated & Bag Type Filtration Systems INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS Thank you for your purchase of a WARCO Series GH Filtration System.

More information

Remove and install steering gear

Remove and install steering gear ZF Aftermarket Neuwied Remove and install steering gear JRB5090 PUBLICATION XZB3502EN NOTE Secure vehicle against rolling away. Ensure proper cleanliness when working on the servo-steering. Cable connections

More information

INTRODUCTION: Rotary pumps are positive displacement pumps. The rate of flow (discharge) of rotary pump remains constant irrespective of the

INTRODUCTION: Rotary pumps are positive displacement pumps. The rate of flow (discharge) of rotary pump remains constant irrespective of the INTRODUCTION: Rotary pumps are positive displacement pumps. The rate of flow (discharge) of rotary pump remains constant irrespective of the pressure. That is, even at very high pressure, these pumps can

More information

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS HEF DOLPHIN FLOAT PUMP Corporate Office: Pump Manufacturing: Apparatus Division: 325 Spring Lake Drive 1051 Palmer St. 920 Kurth Rd. Itasca, Illinois 60143-2072 Chippewa Falls, WI

More information

CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL

CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL 2 Table of Contents Section 1: General Information Page Handle Assembly Instructions 4 Maintenance All Models 6 Oil Change Procedures All Models 9 Height Adjustment

More information

1370 S/n & Up

1370 S/n & Up Operator s Manual Operator s Manual 1370 S/n 8736001 & Up THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF J.I. CASE OR IT S SUCCESSORS. J.I. CASE AND IT S SUCCESSORS ARE NOT RESPONSIBLE

More information

Module 4: Actuators. CDX Diesel Hydraulics. Terms and Definitions. Cylinder Actuators

Module 4: Actuators. CDX Diesel Hydraulics. Terms and Definitions. Cylinder Actuators Terms and Definitions Cylinder Actuators Symbols for Actuators Terms and Definitions II Cylinders Providing Linear Motion Cylinders Providing Angular Motion Parts of Actuators Mounting of Actuators Seals

More information

QuickServe Online ( ) ISB6.7 CM2350 B101 Service Manual

QuickServe Online ( ) ISB6.7 CM2350 B101 Service Manual Page 1 of 31 (/qs3/pubsys2/xml/en/manual/2883567/2883567-titlepage.html) Select Service Tools Recommended Cummins Service Tools 0.043 inch orificed diagnostic fuel line, Part Number 3164621 Diagnostic

More information

Table 6-1. Problems and solutions with pump operations. No Fluid Delivery

Table 6-1. Problems and solutions with pump operations. No Fluid Delivery Table 6-1. and solutions with pump operations No Fluid Delivery Fluid level in the reservoir is low. Oil intake pipe or inlet filter is plugged. Air leak in the inlet line prevents priming or causes noise

More information

ITT. Goulds Pumps. Marlow Series 20EVP. Engineered for life. Commercial Water

ITT. Goulds Pumps. Marlow Series 20EVP. Engineered for life. Commercial Water Goulds Pumps Marlow Series 2EVP Vertical In-Line Self-Priming Centrifugal Pumps for Petroleums and Solvents STANDARD UNIT INCLUDES: Goulds Pumps is a brand of ITT Corporation. www.goulds.com Engineered

More information

The Available Solution CYCLO DRIVE. Gearmotors & Speed Reducers. Series

The Available Solution CYCLO DRIVE. Gearmotors & Speed Reducers. Series The Available Solution CYCLO DRIVE Gearmotors & Speed Reducers 6000 Series WHAT DO YOU THINK OF THIS? THESE ARE THE ADVANTAGES OF THE NEWEST CYCLO, 6000 SERIES: More frame sizes, gear ratios and motor

More information

Syslog Technologies Innovative Thoughts

Syslog Technologies Innovative Thoughts AUTOMATIC PNEUMATIC WATER PUMPING SYSTEM SYNOPSIS The aim of the project is pneumatic operated water pumping system. Radial plunger Pneumatic Water pumping system are reciprocating pump in which the piston

More information