ATTENTION ADVANCE SERVICE BULLETIN INFORMATION

Transcription

1 NUMBER: GROUP: Body EFFECTIVE DATE: Jan. 19, 2001 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without written permission of DaimlerChrysler Corporation. DAIMLERCHRYSLER MAIL MANAGEMENT SYSTEM DATE: DEC. 29, 2000 ATTENTION ADVANCE SERVICE BULLETIN INFORMATION NOTICE: PARTS AVAILABILITY INFORMATION The following bulletin, , is being provided in advance. PARTS ARE NOT EXPECTED TO BE AVAILABLE until the effective date January 19, 2001 shown on the bulletin. Unless there is an immediate need, DO NOT ORDER PARTS until the effective date on the TSB. All orders will be held until stock is on hand. Form TSB-005 Rev February 3, 2000

2 NUMBER: GROUP: Body DATE: Jan. 19, 2001 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in a retreival system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of DaimlerChrysler Corporation. SUBJECT: Intermittent Operation Of The Automatic One-Touch Window Down Feature OVERVIEW: This bulletin involves installing a new window regulator. MODELS: 2000 (AN) Dakota 2000 (DN) Durango NOTE: THIS BULLETIN APPLIES TO VEHICLES EQUIPPED WITH POWER WINDOWS (SALES CODE JPD) BUILT ON OR AFTER MAY 22, 2000 (MDH 0522XX). IN ADDITION, FOR DAKOTA MODELS, THIS BULLETIN APPLIES TO DAKOTA QUAD CAB (AN84) VEHICLES ONLY. SYMPTOM/CONDITION: Intermittent operation of the driver s power window automatic one-touch window down feature. DIAGNOSIS/REPAIR PROCEDURES: Turn the ignition switch to the RUN position. Operate the driver side power window automatic one-touch window down feature. Repeat several times. If the driver side power window automatic one-touch window down feature intermittently operates, perform the Repair Procedure. NOTE: DUE TO THE NATURE OF THIS CONDITION, IT MAY BE DIFFICULT TO DUPLICATE THE SYMPTOM. IF THE CUSTOMER INDICATES THAT THE DRIVER SIDE POWER WINDOW AUTOMATIC ONE-TOUCH WINDOW DOWN FEATURE INTERMITTENTLY OPERATES, PERFORM THE REPAIR PROCEDURE. PARTS REQUIRED: Qty. Part No. Description AB Regulator, Window REPAIR PROCEDURE: THIS REPAIR IS COMPATIBLE WITH DAIMLERCHRYSLER S MOBILE SERVICE PROGRAM AND DOES NOT REQUIRE HOISTS OR OTHER FULL SERVICE FACILITY SPECIAL EQUIPMENT.

3 Release door latch and open door. 2. Roll window down. 3. Remove screws attaching trim panel to door (Fig. 1). 1 - TRIM PANEL 2 - INNER DOOR PANEL 3 - INSIDE DOOR HANDLE BRACKET 4 - TRIM PANEL 5 - INSIDE DOOR HANDLE Fig. 1 DOOR TRIM PANEL CAUTION: DO NOT FORCIBLY PULL TRIM PANEL FROM DOOR, DAMAGE TO TRIM PANEL MAY OCCUR. 4. Simultaneously lift upward and outward to release retainer steps from inner door panel (Fig. 2).

4 Fig. 2 TRIM PANEL RETAINER 1 - INNER DOOR PANEL 2 - TRIM PANEL 3 - RETAINER HOOKS 5. Disengage inside handle and inside lock linkage rods from inside handle assembly. 6. Disconnect speaker harness wire connector (Fig. 3). 1 - POWER MIRROR SWITCH 2 - SPEAKER 3 - POWER WINDOW SWITCH 4 - SPEAKER WIRE HARNESS CONNECTOR Fig. 3 POWER DOOR LOCK/WINDOW CONNECTOR 7. Disengage power mirror wire connector.

5 Disengage clips attaching power window/lock switch panel to door trim panel. Disengage wire connector from switch panel. 9. Separate door trim panel from vehicle. 10. Partially remove waterdam. 11. Position glass to access the liftplate fasteners. Remove the fasteners. 12. Disengage glass from regulator lift channel. 13. Position glass up into door frame (rest glass on a block of wood on door reinforcement). 14. Disconnect regulator wire harness. 15. Remove screws attaching window regulator to door inner panel (Fig. 4). 1 - FRONT DOOR 2 - POWER WINDOW REGULATOR 3 - NUT Fig. 4 WINDOW REGULATOR 16. Remove window regulator from door. 17. Position new window regulator p/n AB into door. 18. Loosely install screws attaching window regulator to door inner panel. 19. Position glass onto window regulator lift channel. 20. Install glass to lift channel fasteners. 21. Cycle the window glass to the full up position. 22. Tighten bolts attaching lower front glass run channel to door inner panel. 23. Tighten fasteners holding window regulator to door inner panel. 24. Connect regulator wire harness. 25. Install waterdam. 26. Position trim panel at door. 27. Engage wire connector for window/lock switch panel. 28. Engage power mirror wire connector. 29. Connect speaker harness wire connector. 30. Engage inside handle and inside lock linkage rods to inside handle assembly.

6 Align trim panel retainer steps with inner door panel and slide trim panel into place. 32. Install screws attaching trim panel to door. POLICY: Reimbursable within the provisions of the warranty. TIME ALLOWANCE: Labor Operation No: Hrs. FAILURE CODE: P8 New Part