Size: px
Start display at page:

Download ""

Transcription

1 Page 1 of 5 Section 03-01C: Engine, 4.0L V-6 IN-VEHICLE SERVICE Workshop Manual Camshaft SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Sensor Adjusting Wrench T94T A Removal NOTE: It is necessary to replace oil pan gasket (6710) when removing and installing engine front cover (6019). On Ranger and Explorer vehicles, it is necessary to remove the engine (6007) to remove the oil pan (6675). On Aerostar, it is necessary to remove the transmission to properly reseal oil pan. 1. On Ranger and Explorer vehicles, remove engine as outlined in this section. 2. On Aerostar vehicles, remove radiator (8005) as outlined in Section and remove transmission as outlined in Group Remove the upper and lower intake manifolds as outlined in this section. 4. Remove the engine front cover as outlined in this section. 5. Remove the oil pan as outlined in this section. 6. Remove the hold-down clamp (12270), screw and oil pump drive shaft from the rear of the cylinder block (6010). 7. NOTE: Ranger and Explorer vehicles have a CID sensor mounted on top of the oil pump drive assembly. Sensor Adjusting Wrench T94T A is designed for easy access to the hold-down clamp screw. For Ranger and Explorer vehicles, disconnect the engine wiring harness connector at the CID sensor. 8. Remove the valve covers (6582) and rocker arm shaft (6563) assemblies as outlined in this section. Lift out the push rods (6565) and place in a marked rack so they can be installed in the same location. 9. Remove the valve tappets (6500). Refer to tappet removal and installation procedure in this section. 10. Push the timing chain/belt tensioner (6K254) into the retracted position, and install the retaining clip Camshaft Sprocket 2 Camshaft Timing Mark (Part of 6256) 3 6K297 Timing Chain Guide 4 Crankshaft Timing Mark (Part of 6306) Crankshaft Sprocket 6 6K254 Timing Chain/Belt Tensioner 11. Remove the camshaft sprocket attaching bolt and remove the camshaft sprocket (6256) from the camshaft. 12. Remove the camshaft thrust plate (6269). 13. Remove the camshaft (6250) carefully from the cylinder block, avoiding any damage to the camshaft bearings.

2 Page 2 of 5 Installation 1. Oil the camshaft journals and cam lobes with SAE 50 Service SG engine oil or equivalent meeting Ford specification ESE-M2C39-F. Insert the camshaft key. 2. Install the camshaft in the cylinder block, being careful to avoid damaging the bearing surfaces. 3. Install the thrust plate as shown so that it covers the main oil gallery. Tighten the attaching screws to 9-13 Nm (7-10 lb-ft). 4. Turn the camshaft and crankshaft (6303) as necessary to align the timing marks. Install the camshaft sprocket, install the attaching bolt and tighten to Nm (44-50 lb-ft) Camshaft Sprocket 2 Camshaft Timing Mark (Part of 6256) 3 6K297 Timing Chain Guide 4 Crankshaft Timing Mark (Part of 6306) Crankshaft Sprocket 6 6K254 Timing Chain/Belt Tensioner 5. Check the camshaft for correct end play. Refer to Section End play should be mm ( inch). Remove the clip from the timing chain tensioner. 6. Position the valve tappets in their original locations as outlined. Apply SAE 50 Service SG or equivalent oil meeting Ford specification ESE-M2C39-F to both ends of the push rods. Install the push rods in the same locations as removed. 7. Install the intake manifolds as outlined in this section. 8. Install the rocker arm shaft assemblies. Tighten the rocker arm stand bolts evenly and in sequence to 6-8 Nm (53-71 lb-in). Refer to Rocker Arm, Installation in this section. 9. Install the valve covers as outlined. 10. Install the engine front cover as an assembly. Refer to Engine Front Cover, Installation, in this section. 11. Install the oil pump drive, hold-down clamp and screw. For Ranger and Explorer vehicles refer to Installation, Ranger and Explorer below.

3 Page 3 of Install oil pan as outlined in this section. 13. Install engine front cover as outlined in this section. 14. On Ranger and Explorer vehicles, install engine as outlined in this section. 15. On Aerostar vehicles, install transmission as outlined in this section. 16. On Aerostar, install the radiator. 17. Fill the cooling system to the proper level with the specified coolant and bleed the cooling system as outlined in Section Fill the crankcase with the specified quantity and grade of oil. 19. NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy. Connect the battery ground cable (14301) to the battery. 20. Run the engine at fast idle speed and check for coolant, fuel, vacuum and oil leaks. Installation, Ranger and Explorer SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number CID Testing Wiring Harness T94T-50-B 1. After performing Steps 1-11 above, rotate crankshaft until TDC mark on the damper is accessible. If not present, place an additional mark on the damper at 26 degrees After Top Dead Center (ATDC). This position is 34mm (1.34 inches) counterclockwise from the Top Dead Center (TDC) mark. 2. Position No. 1 cylinder to 26 ATDC between compression and ignition stroke. (Both intake and exhaust valves must be closed with TDC mark on vibration damper at pointer.) 3. Lubricate oil pump drive pinion and O-ring on assembled oil pump drive gear and CID sensor with SM-2C 1013-A oil. Do not get oil above mounting flange.

4 Page 4 of K073 CID Sensor 2 E S O-Ring Oil Pump Drive Assembly Engine Hold-Down Clamp 6 E Screw A Tighten to Nm (13-15 Lb-Ft) B Maximum Level for Pre-Oiling Drive Gear C Minimum Level for Pre-Oiling Drive Gear 4. NOTE: Normal CID sensor rotation is clockwise viewed from top of CID sensor. Align the CID sensor rotor as shown with the trailing edge of the vane lined up with the short mark at the left-hand side of the plastic window. 5. Position the sensor above its hole at right angles to the block rear face. 6. Install the assembled CID sensor and oil pump drive gear into the engine. As the assembly is pushed into place, the camshaft gear will rotate the sensor vane clockwise toward the center of the window. 7. Rotate the CID sensor counterclockwise. Install clamp and screw finger-tight. Rotate the sensor back to its position at right angles to the back of the block. 8. Connect the CID Testing Wiring Harness T94T-50-B to the CID Sensor. 9. Connect the CID Testing Wiring Harness leads: a. Red harness wire to battery positive terminal. b. Black harness wire to battery negative terminal. c. Voltmeter positive lead to harnesses white lead. d. Voltmeter negative lead to battery negative terminal.

5 Page 5 of 5 1 T94T-50-B CID Testing Wiring Harness 2 White Lead 3 Red Lead 4 Positive Terminal (Part of 10655) Battery 6 Red Lead (Part of ) Rotunda Digital Volt-Ohmmeter or Equivalent 8 Black Lead (Part of ) 9 Negative Terminal (Part of 10655) 10 Black Lead 11 Connector (Attaches to CID Sensor) 10. Rotate engine two revolutions to take up slack in timing chain and return No. 1 cylinder to its compression stroke. 11. Verify that No. 1 cylinder is on its compression stroke (both valves closed). 12. NOTE: No. 1 cylinder must be at 26 degrees After Top Dead Center (ATDC) to set CID sensor. Continue to rotate the crankshaft until the new 26 degrees ATDC mark lines up with the timing pointer. 13. NOTE: The voltmeter will register battery voltage whenever the CID sensor closes and makes a complete circuit. Rotate the CID sensor and stop at the exact point where the sensor switches from 0 to 12 volts on the voltmeter. 14. NOTE: The final movement to set the CID sensor must be in a COUNTERCLOCKWISE direction. Rotate the CID sensor clockwise past the CID switching point (from 12 to 0 volts). 15. Rotate the CID sensor counterclockwise and stop at the exact point the voltmeter switches from 0 to 12 volts. 16. Tighten the CID sensor hold-down bolt to Nm (13-15 lb-ft) using Sensor Adjusting Wrench T94T A. 17. Disconnect the testing wiring harness and the voltmeter and proceed with Step 12 of Installation above.

1995 Aerostar/Ranger/Explorer

1995 Aerostar/Ranger/Explorer Page 1 of 13 Section 03-01C: Engine, 4.0L V-6 DISASSEMBLY AND ASSEMBLY 1995 Aerostar/Ranger/Explorer Workshop Manual Engine Disassembly 1. NOTE: Before starting disassembly, remove all wiring harnesses,

More information

IN-VEHICLE SERVICE. Engine Components

IN-VEHICLE SERVICE. Engine Components file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk31a14.htm~gen~ref.htm Page 1 of 10 Section 03-01A: Engine, 2.3L I-4 IN-VEHICLE SERVICE 1997 Ranger Workshop Manual Engine Components The views shown

More information

Page 1 of 6 Section 03-01B: Engine, 7.5L MFI Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 05/17/2000 Engine Front Cover SPECIAL SERVICE TOOL(S) REQUIRED Description Crankshaft Damper Remover

More information

ALLDATA Online Ford Focus L4-2.0L DOHC VIN 5 - Service and Repair. Service and Repair

ALLDATA Online Ford Focus L4-2.0L DOHC VIN 5 - Service and Repair. Service and Repair Page 1 of 22 Service and Repair NOTE: Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools shown in this procedure. Timing Belt Special

More information

ASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s)

ASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s) 303-01A-1 ASSEMBLY Engine Special Tool(s) Tensioner, Timing Chain 303-571 (T97T-6K254-A) Special Tool(s) 303-01A-1 Installer, Crankshaft Vibration Damper 303-102 (T74P-6316-B) Holding Tool, Camshaft Sprocket

More information

Engine. Special Tool(s) Adapter for (T97T-6256-A) Adapter for (T97T-6256-D)

Engine. Special Tool(s) Adapter for (T97T-6256-A) Adapter for (T97T-6256-D) SECTION 303-01A: Engine 4.0L SOHC 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 05/10/2010 Engine Special Tool(s) Adapter for 303-564 303-578 (T97T-6256-A) Adapter for 303-577 303-576

More information

2003 Taurus/Sable Workshop Manual

2003 Taurus/Sable Workshop Manual Page 1 of 24 SECTION 303-01A: Engine 3.0L (2V) ASSEMBLY 2003 Taurus/Sable Workshop Manual Engine Special Tool(s) Piston Ring Compressor 303- D032 (D81L-6002-C) Camshaft Bearing Set 303-017 (T65L-6250-A)

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Rotate engine clockwise and position cylinder No. 1 on TDC of compression stroke. Ensure "O" mark on crankshaft pulley aligns

More information

2010 Transit Connect Workshop Manual. 31. Remove the 3 bolts, thermostat housing and thermostat.

2010 Transit Connect Workshop Manual. 31. Remove the 3 bolts, thermostat housing and thermostat. 31. Remove the 3 bolts, thermostat housing and thermostat. 32. Remove the 2 bolts, stud bolt and the A/C compressor. 33. Remove the bolt and the KS. 34. Remove the 8 bolts and the crankcase vent oil separator.

More information

1996 Aerostar/Ranger/Explorer

1996 Aerostar/Ranger/Explorer Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding

More information

2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical)

2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 4: Aligning Timing Marks 6. Loosen the timing belt tensioner bolt and the stud. 7. After pushing up the tensioner plate completely with

More information

2001 Ford FOCUS. Submodel: ZTS Engine Type: L4 Liters: 2.0 Fuel Delivery: FI Fuel: GAS. Timing Belt

2001 Ford FOCUS. Submodel: ZTS Engine Type: L4 Liters: 2.0 Fuel Delivery: FI Fuel: GAS. Timing Belt 2001 Ford FOCUS Submodel: ZTS Engine Type: L4 Liters: 2.0 Fuel Delivery: FI Fuel: GAS SECTION 303-01A: Engine??? 2.0L Zetec-E (Zetec) 2001 Focus Workshop Manual IN-VEHICLE REPAIR Procedure revision date:

More information

Timing Belt: Service and Repair Installation

Timing Belt: Service and Repair Installation 1998 Mercury Mystique L4-122 2.0L DOHC VIN 3 SFI Copyright 2008, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Installation NOTE:Ford does not provide camshaft gear timing marks, or information to

More information

IN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent

IN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent 303-01A-1 IN-VEHICLE REPAIR Cylinder Head Special Tool(s) Torque Wrench Extension 303-575 (T97T-6256-F) or equivalent Special Tool(s) 303-01A-1 Timing Tool, Crankshaft TDC 303-573 (T97T-6303-A) or equivalent

More information

1996 Aerostar/Ranger/Explorer

1996 Aerostar/Ranger/Explorer Page 1 of 10 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Engine Front Cover SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch

More information

Timing Drive Components

Timing Drive Components 2006 Ford F 150 : Engine Mechanical > Engine, 5.4L (3V) > IN VEHICLE REPAIR > Timing Drive Components Timing Drive Components Listen SECTION 303 01C: Engine 5.4L (3V) 2006 F 150/Mark LT Workshop Manual

More information

Intake Components 1117

Intake Components 1117 Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold

More information

DESCRIPTION AND OPERATION

DESCRIPTION AND OPERATION 303-01B-10 Engine 3.0L 303-01B-10 DESCRIPTION AND OPERATION Upper Engine Components G72932 en 303-01B-11 Engine 3.0L 303-01B-11 DESCRIPTION AND OPERATION (Continued) Item Part Number Description 1 9H589

More information

IN-VEHICLE REPAIR. Camshaft RH. Removal. 2. Remove the RH valve cover. For additional information, refer to Valve Cover RH in this section.

IN-VEHICLE REPAIR. Camshaft RH. Removal. 2. Remove the RH valve cover. For additional information, refer to Valve Cover RH in this section. 303-01B-1 IN-VEHICLE REPAIR Camshaft RH Special Tool(s) Compressor, Valve Spring 303-1039 Wedge, Timing Chain 303-1175 303-01B-1 2. Remove the RH valve cover. For additional information, refer to Valve

More information

2007 Ford Freestyle SEL

2007 Ford Freestyle SEL Fig. 279: Exploded View Of Engine Heads, Intake & Exhaust Components Item Part Number Description 1 9D475 Exhaust gas recirculation (EGR) system module 2 9D477 EGR module tube 3 9F485 RH exhaust manifold

More information

IN-VEHICLE REPAIR. Camshaft RH. Removal. 2. Remove the RH valve cover. For additional information, refer to Valve Cover RH in this section.

IN-VEHICLE REPAIR. Camshaft RH. Removal. 2. Remove the RH valve cover. For additional information, refer to Valve Cover RH in this section. 303-01C-1 IN-VEHICLE REPAIR Camshaft RH Special Tool(s) 303-01C-1 2. Remove the RH valve cover. For additional information, refer to Valve Cover RH in this section. Compressor, Valve Spring 3. NOTICE:

More information

Page 1 of 75 303-01D Engine - 5.2L 32V Ti-VCT 2016 Mustang Assembly Procedure revision date: 12/15/2016 Special Tool(s) / General Equipment Engine Base Part Number: 6L084 205-142 (T80T-4000-J) Installer,

More information

Timing Drive Components ( )

Timing Drive Components ( ) Page 1 of 14 (12.65.13) Removal 1. Remove the engine front cover. For additional information, refer to For additional information, refer to. 2. Remove the spark plugs. 3. Remove the crankshaft position

More information

Classification: Reference: Date: VE30DE CAM TIMING

Classification: Reference: Date: VE30DE CAM TIMING Classification: Reference: Date: EM93-002 NTB93-126 September 2, 1993 VE30DE CAM TIMING APPLIED VEHICLE(S): All equipped with VE30DE Engine SERVICE INFORMATION When servicing VE30DE engine cylinder heads,

More information

Page 1 of 9 SECTION 303-01B: Engine 2.0L SPI 2002 Focus Workshop Manual ASSEMBLY Procedure revision date: 12/14/2000 Engine Special Tool(s) Crankshaft Rear Seal Pilot 303-329 (T88P-6701-B2) Crankshaft

More information

(g)honda Service Bulletin

(g)honda Service Bulletin (g)honda Service Bulletin 09-010 February 25, 2017 05909 Version 5 Engine Rattles at Cold Start-Up Supersedes 09-010, dated March 17, 2016, to revise the information highlighted in yellow. REVISION SUMMARY

More information

Technical Service BULLETIN

Technical Service BULLETIN Technical Service BULLETIN May 19, 2003 Title: Models: 00 02 Celica GTS EG010-03 ENGINE Introduction In some cases, owners of 2000 2002 model year Celica GTS vehicles equipped with the 2ZZ GE engine may

More information

Engine. Special Tool(s) Compressor, Valve Spring (T97P-6565-AH) Compressor Spacer, Valve Spring (T91P-6565-AH)

Engine. Special Tool(s) Compressor, Valve Spring (T97P-6565-AH) Compressor Spacer, Valve Spring (T91P-6565-AH) Page 1 of 41 SECTION 303-01A: Engine 5.4L (2V) 2000 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis Workshop Manual ASSEMBLY Procedure revision date: 04/04/2003 Engine Special Tool(s) Compressor,

More information

ASSEMBLY Procedure revision date: 11/22/2001

ASSEMBLY Procedure revision date: 11/22/2001 Page 1 of 39 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:08 PM To: 'Evan Groenke' Subject: 2.5L Engine Re-assembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop

More information

DISASSEMBLY Procedure revision date: 11/22/2001

DISASSEMBLY Procedure revision date: 11/22/2001 Page 1 of 31 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:06 PM To: 'Evan Groenke' Subject: 2.5 L Engine Disassembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop

More information

Service and Repair SERVICE POINTS OF REMOVAL. Select Vehicle New TSBs Technician's Reference Mitsubishi 3000GT V6-2972cc 3.

Service and Repair SERVICE POINTS OF REMOVAL. Select Vehicle New TSBs Technician's Reference Mitsubishi 3000GT V6-2972cc 3. 1 of 12 5/4/2008 10:31 PM Home Account Contact ALLDATA Log Out Help METRO TOYOTA Select Vehicle New TSBs Technician's Reference 1992 Mitsubishi 3000GT V6-2972cc 3.0L DOHC Vehicle Level Engine, Cooling

More information

SECTION C Engine 5.4L (3V)

SECTION C Engine 5.4L (3V) 303-01C-i Engine 5.4L (3V) 303-01C-i SECTION 303-01C Engine 5.4L (3V) CONTENTS PAGE IN-VEHICLE REPAIR Timing Drive Components... 303-01C-2 303-01C-2 Engine 5.4L (3V) 303-01C-2 IN-VEHICLE REPAIR Timing

More information

IN-VEHICLE REPAIR. Engine Front Cover

IN-VEHICLE REPAIR. Engine Front Cover 303-01A-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01A-1 Special Tool(s) SAE 5W-20 Premium WSS-M2C930-A Synthetic Blend Motor Oil Alignment Plate, Camshaft XO-5W20-QSP (in Canada

More information

2012 Kia Soul L4 2.0L

2012 Kia Soul L4 2.0L 2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 1 Removal Engine removal is not required for this procedure. CAUTION: Use fender

More information

Timing Drive Components Camshaft Timing

Timing Drive Components Camshaft Timing SECTION 303-01B: Engine 4.0L SOHC 1998 Explorer/Mountaineer Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/17/2002 Timing Drive Components Camshaft Timing Special Tool(s) Timing Chain Tensioner

More information

IN-VEHICLE REPAIR. Timing Drive Components. Removal. 3. Position the crankshaft keyway at the 12 o clock position.

IN-VEHICLE REPAIR. Timing Drive Components. Removal. 3. Position the crankshaft keyway at the 12 o clock position. 303-01B-1 IN-VEHICLE REPAIR Timing Drive Components 303-01B-1 Special Tool(s) Compressor, Valve Spring 303-1039 Locking Tool, Camshaft Phaser Sprocket 303-1046 3. Position the crankshaft keyway at the

More information

Page 1 of 18 303-01C Engine 5.4L (3V) 2010 F-150 IN-VEHICLE REPAIR Procedure revision date: 07/01/2009 Timing Drive Components Special Tool(s) Compressor, Valve Spring 303-1039 Holding Tool, Crankshaft

More information

ENGINE REMOVAL Install: Exhaust pipe 1 5. Tighten: Nuts (exhaust pipe) 2. Exhaust pipe nut 20 Nm (2.0 m kgf, 14 ft lbf) 6.

ENGINE REMOVAL Install: Exhaust pipe 1 5. Tighten: Nuts (exhaust pipe) 2. Exhaust pipe nut 20 Nm (2.0 m kgf, 14 ft lbf) 6. ENGINE REMOVAL 4. Install: Gasket New Exhaust pipe 1 5. Tighten: Nuts (exhaust pipe) 2 Exhaust pipe nut 20 Nm (2.0 m kgf, 14 ft lbf) 6. Install: Clamp Slide the clamp onto the end of the muffler and insert

More information

TIMING BELT TENSIONER FOR AFTERMARKET RENAULT G8T 2.2L DIESEL ENGINE (Revision date: 06/24/1999)

TIMING BELT TENSIONER FOR AFTERMARKET RENAULT G8T 2.2L DIESEL ENGINE (Revision date: 06/24/1999) 1. Allow the engine and tensioner to stabilize to the same relative ambient temperature before installing a tensioner for proper belt tension adjustment. Do not attempt to install a cool tensioner onto

More information

TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT

TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove right front wheel. 3. Remove belt splash shield. 4. Remove accessory drive belts.

More information

IN-VEHICLE REPAIR. Timing Drive Components. Removal. 3. Position the crankshaft keyway at the 12 o clock position.

IN-VEHICLE REPAIR. Timing Drive Components. Removal. 3. Position the crankshaft keyway at the 12 o clock position. 303-01C-1 IN-VEHICLE REPAIR Timing Drive Components 303-01C-1 Special Tool(s) Compressor, Valve Spring 303-1039 Locking Tool, Camshaft Phaser Sprocket 303-1046 3. Position the crankshaft keyway at the

More information

CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage.

CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage. REMOVAL Timing Chain 1. Disconnect negative battery cable. 2. Drain cooling system. 3. Remove upper intake manifold. 4. Remove cylinder head covers, crankshaft vibration damper, and timing chain cover.

More information

IN-VEHICLE REPAIR. Timing Drive Components Camshaft Drive Cassette, LH. Special Tool(s) Holding Tool, Camshaft Sprocket (T97T-6256)

IN-VEHICLE REPAIR. Timing Drive Components Camshaft Drive Cassette, LH. Special Tool(s) Holding Tool, Camshaft Sprocket (T97T-6256) 303-01A-1 IN-VEHICLE REPAIR Timing Drive Components Camshaft Drive Cassette, LH 303-01A-1 Special Tool(s) Holding Tool, Camshaft Sprocket 303-564 (T97T-6256) Adapter for 303-564 303-578 (T97T-6256-A) Holding

More information

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) 1 of 15 8/7/2016 2:34 PM 2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Removal and Installation 2 of 15

More information

Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)

Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR) SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,

More information

GENERAL INSTRUCTIONS. PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: c.i.d. Chevrolet V8 Engines CATALOG #2117

GENERAL INSTRUCTIONS. PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: c.i.d. Chevrolet V8 Engines CATALOG #2117 Page 1 PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: 283-400 c.i.d. Chevrolet V8 Engines GENERAL INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most installations

More information

Timing Belt: Service and Repair Timing Belt Replacement

Timing Belt: Service and Repair Timing Belt Replacement 2003 Saturn Truck VUE V6-3.0L VIN B Copyright 2007, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Timing Belt Replacement Removal Procedure 1. Remove the front timing belt cover. 2. Rotate the crankshaft

More information

SUMMARY TOOL INFORMATION

SUMMARY TOOL INFORMATION Applies To: See VEHICLES AFFECTED Service Bulletin 09-010 October 21, 2011 Engine Rattles at Cold Start-Up (Supersedes 09-010, dated August 17, 2010, to revise the information marked by the black bars)

More information

1 of 10 2/10/2017 5:20 PM

1 of 10 2/10/2017 5:20 PM 1 of 10 2/10/2017 5:20 PM Crankshaft Pulley Removal NOTICE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as instructed in this procedure. The crankshaft

More information

file://c:\program Files\tsocache\OFFICE_5416\SY1~us~en~file=SY131B46.htm~gen~ref...

file://c:\program Files\tsocache\OFFICE_5416\SY1~us~en~file=SY131B46.htm~gen~ref... Page 1 of 41 SECTION 303-01B: Engine 4.6L and 5.4L 2000 F-150 Workshop Manual ASSEMBLY Procedure revision date: 01/27/2004 Engine 4.6L Special Tool(s) Compressor, Valve Spring 303-567 (T97P-6565-AH) Compressor

More information

RECOMMENDET INSTALLATION PROCEDURE Timing Belt Tensioner for Aftermarket OPEL 2.0L SOHC, Fam. 2 (Revision date: 04/27/1999)

RECOMMENDET INSTALLATION PROCEDURE Timing Belt Tensioner for Aftermarket OPEL 2.0L SOHC, Fam. 2 (Revision date: 04/27/1999) 1. Allow the engine and tensioner to stabilize to the same relative ambient temperature before installing a tensioner for proper belt tension adjustment. Do not attempt to install a cool tensioner onto

More information

Page 1 of 8 303-01A Engine 2.3L 2007 Escape/Mariner/Escape Hybrid/Mariner Hybrid IN-VEHICLE REPAIR Procedure revision date: 10/05/2008 Cylinder Head Special Tool(s) Alignment Plate, Camshaft 303-465 (T94P-6256-CH)

More information

11/29/2017 Engine Cooling - Coolant Pump - Removal and Installation 2010 Ford Edge MotoLogic Engine Cooling 2010 Edge, MKX

11/29/2017 Engine Cooling - Coolant Pump - Removal and Installation 2010 Ford Edge MotoLogic Engine Cooling 2010 Edge, MKX 2010 Edge Report a problem with this article 303-03 Engine Cooling 2010 Edge, MKX REMOVAL AND INSTALLATION Procedure revision date: 10/04/2010 Coolant Pump Special Tool(s) Camshaft Holding Tool 303-1248

More information

2012 Kia Soul L4 2.0L

2012 Kia Soul L4 2.0L 2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 2 Installation 1. The TDC marks of the intake and exhaust CVVT sprockets are

More information

GM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions

GM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions GM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions Set Includes: Locking Tool... 536594 Locking Tool... 536595 Crankshaft Holding Tool... 536596 Alignment Gauge... 536608 Belt Installation

More information

Page 1 of 21 303-01C Engine 5.4L (3V) 2009 F-150 REMOVAL Procedure revision date: 03/26/2009 Cylinder Head Special Tool(s) 3 Jaw Puller 303-D121 or equivalent Compressor, Valve Spring 303-1039 Holding

More information

COMPONENT LOCATOR > DISASSEMBLED VIEWS

COMPONENT LOCATOR > DISASSEMBLED VIEWS Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine

More information

5.7L V Chevrolet Camaro * PLEASE READ THIS FIRST * ENGINE IDENTIFICATION VEHICLE IDENTIFICATION NUMBER (VIN) ADJUSTMENTS

5.7L V Chevrolet Camaro * PLEASE READ THIS FIRST * ENGINE IDENTIFICATION VEHICLE IDENTIFICATION NUMBER (VIN) ADJUSTMENTS 5.7L V8 2001 Chevrolet Camaro 2000-01 ENGINES General Motors 5.7L V8 Chevrolet; Camaro Pontiac; Firebird * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE

More information

2002 Crown Victoria/Grand Marquis Workshop Manual

2002 Crown Victoria/Grand Marquis Workshop Manual Page 1 of 24 SECTION 303-01: Engine 2002 Crown Victoria/Grand Marquis Workshop Manual INSTALLATION Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Installer, Crankshaft Vibration Damper

More information

2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page 1

2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page 1 2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair Timing Belt REMOVAL 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS PERFORMER RPM CAMSHAFT / LIFTERS / LUBE KIT For 343-401 c.i.d. AMC V8 Engines CATALOG # 7132 INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most

More information

DISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage.

DISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage. 303-01A-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Vibration Damper 303-101 (T74P-3616-A) Special Tool(s) Crankshaft Socket 303-674 303-01A-1 Remover, Crankshaft Vibration Damper 303-773

More information

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION

More information

Crankshaft, Remove and Install (Engine Removed) (Z 22 SE)

Crankshaft, Remove and Install (Engine Removed) (Z 22 SE) Page 1 of 36 Crankshaft, Remove and Install (Engine Removed) (Z 22 SE) Remove 1. Remove the engine Note: See operation "Engine, Remove and Install". 2. Separate the manual transmission from the engine.

More information

TIMING CHAIN COMPONENTS

TIMING CHAIN COMPONENTS Page 1 of 30 TIMING CHAIN COMPONENTS Fig. 46: Identifying Camshaft Timing Oil Control Valve Assembly Components With Torque Page 2 of 30 Specifications (1 Of 3) Fig. 47: Identifying Camshaft Timing Oil

More information

2002 Explorer Sport/Sport Trac Workshop Manual

2002 Explorer Sport/Sport Trac Workshop Manual Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)

More information

Timing Drive Components

Timing Drive Components 1 of 27 3/9/2012 8:26 AM Timing Drive Components Special Tool(s) Material LLDATA Online - 2006 Ford Truck Expedition 4WD V8-5.4L VIN 5 -... 2 of 27 3/9/2012 8:26 AM Material Removal 1. Remove the engine

More information

CAMSHAFT ASSEMBLY. Preceding Work: Removal of cylinder head cover. Intake Camshaft and Exhaust Camshaft. Finger Follower and HLA. Camshaft Sprockets

CAMSHAFT ASSEMBLY. Preceding Work: Removal of cylinder head cover. Intake Camshaft and Exhaust Camshaft. Finger Follower and HLA. Camshaft Sprockets 24 02 CAMSHAFT ASSEMBLY Preceding Work: Removal of cylinder head cover Finger Follower and HLA Intake Camshaft and Exhaust Camshaft D20DT Camshaft Sprockets D27DT D20DT D27DT Camshaft Position Sensor Cylinder

More information

Engine Cylinder Head Installation

Engine Cylinder Head Installation Engine Cylinder Head Installation Important: Install the cylinder head without the camshafts. 1. Install the engine cylinder head to the engine block. 2. Install the AIR pump bolt and fir tree fastener

More information

Cylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent

Cylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual INSTALLATION Procedure revision date: 04/03/2009 Cylinder Head Special Tool(s) Compressor, Valve Spring 303-452 (T93P-6565-AR) Heavy Duty

More information

2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head

2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat

More information

The following tools will be required to perform this new service procedure outlined in this bulletin:

The following tools will be required to perform this new service procedure outlined in this bulletin: The following new service information outlined in this bulletin will aid technicians in removal and installation of the cylinder head without the removal of the front engine cover. The new service procedure

More information

PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT CATALOG # 2103 MODEL: 400 c.i.d. Chevrolet V8 engines GENERAL INSTRUCTIONS

PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT CATALOG # 2103 MODEL: 400 c.i.d. Chevrolet V8 engines GENERAL INSTRUCTIONS PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT CATALOG # 2103 MODEL: 400 c.i.d. Chevrolet V8 engines GENERAL INSTRUCTIONS Please study these instructions carefully before you remove your stock camshaft.

More information

Cylinder Head, Remove and Install (Z 22 SE)

Cylinder Head, Remove and Install (Z 22 SE) Page 1 of 29 Cylinder Head, Remove and Install (Z 22 SE) Remove 1. Open the bonnet. 2. Disconnect the battery. 3. Open the engine cover (1). 4. Detach the engine cover. 6 bolts (2) and (3) 5. Release the

More information

CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT

CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT Page 1 of 45 CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT Special Tools J 45027 Tensioner Tool J 45059 Angle Meter Page 2 of 45 Removal Procedure Page 3 of 45 Page 4 of 45 Page 5 of 45 Fig.

More information

3/6/2017 Timing Chain Service and Repair, Removal and Replacement: Valve Timing, Installing and Adjusting

3/6/2017 Timing Chain Service and Repair, Removal and Replacement: Valve Timing, Installing and Adjusting Valve timing, adjusting Special tools and equipment - T10068 Camshaft bar - T10069 Counter support - VAG 1331 Torque wrench (5-50 Nm) - VAG 1332 Torque wrench (40-200 Nm) - AMV 174 004 01 Sealing compound

More information

2003 Saturn Vue. SATURN 3.0L V6 DOHC - L-Series After VIN & Vue

2003 Saturn Vue. SATURN 3.0L V6 DOHC - L-Series After VIN & Vue TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. 2. Raise and support vehicle. Remove right front wheel. Remove lower front splash shield. 3. Lower vehicle. Loosen,

More information

1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers..

1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers.. BELT AND SPROCKETS-TIMING REMOVAL TIMING BELT Zoom 1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers.. CAUTION: When aligning crankshaft and camshaft timing marks

More information

2001 Dodge Dakota ENGINES 4.7L V8

2001 Dodge Dakota ENGINES 4.7L V8 FRONT COVER Removal & Installation 1. Disconnect negative battery cable. Remove drive belt. Remove A/C compressor mounting bolts, and position compressor aside. Drain cooling system. Remove radiator hoses.

More information

MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing.

MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing. MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing. ST 499817100 ENGINE STAND Apply a coat of engine oil to the bearing and

More information

1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza

1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza 1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza ARTICLE BEGINNING 1995-98 ENGINES Subaru - 1.8L & 2.2L 4-Cylinder 1995-97: Impreza (1.8L) 1995-98: Impreza (2.2L), Legacy (2.2L) * PLEASE READ THIS FIRST

More information

PERFORMER-PLUS Camshaft/Lifters/Lube Kit CATALOG #2157 MODEL: c.i.d. Pontiac V8, 1965 & later

PERFORMER-PLUS Camshaft/Lifters/Lube Kit CATALOG #2157 MODEL: c.i.d. Pontiac V8, 1965 & later PERFORMER-PLUS Camshaft/Lifters/Lube Kit CATALOG #2157 MODEL: 350-455 c.i.d. Pontiac V8, 1965 & later CAMSHAFT: Edelbrock Performer-Plus camshafts are ground specifically for use with the corresponding

More information

Timing Chain, Balancer Shaft, Replace (Z 22 SE)

Timing Chain, Balancer Shaft, Replace (Z 22 SE) Page 1 of 34 Timing Chain, Balancer Shaft, Replace (Z 22 SE) Remove 1. Open the bonnet. 2. Disconnect the battery. 3. Open the engine cover (1). 4. Detach the engine cover. 6 bolts (2) and (3) 5. Release

More information

TIMING CHAIN. TIMING CHAIN Removal and Installation EM-35 PFP:13028 EBS00I2X KBIA2511E

TIMING CHAIN. TIMING CHAIN Removal and Installation EM-35 PFP:13028 EBS00I2X KBIA2511E TIMING CHAIN Removal and Installation PFP:13028 EBS00I2X A EM C D E F G H I J K L M KBIA2511E EM-35 1. Camshaft sprocket (left bank EXH) 2. Camshaft sprocket (left bank INT) 3. Camshaft sprocket (right

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect

More information

PERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7102 MODEL: c.i.d. Chevrolet V8, 1957 & later

PERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7102 MODEL: c.i.d. Chevrolet V8, 1957 & later PERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7102 MODEL: 262-400 c.i.d. Chevrolet V8, 1957 & later CAMSHAFT: Edelbrock Performer RPM camshafts are ground specifically for use with the corresponding

More information

1999 E-Series Workshop Manual

1999 E-Series Workshop Manual http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before

More information

Zoom and Print Options

Zoom and Print Options Vehicle» Engine, Cooling and Exhaust» Engine» Timing Components» Timing Chain» Service and Repair» Procedures» Timing Chain and Sprockets Replacement Timing Chain and Sprockets Replacement Tools Required

More information

SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES

SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES ENGINE FD620D, K SERIES SPECIFICATIONS SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2.

More information

ATech Timing Belt Tensioner (979756) PSA EW10A 2.0L Engine

ATech Timing Belt Tensioner (979756) PSA EW10A 2.0L Engine Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must

More information

CYLINDER HEAD > CAMSHAFT, ENGINE > REMOVAL > LEFT

CYLINDER HEAD > CAMSHAFT, ENGINE > REMOVAL > LEFT Page 1 of 12 2012 Dodge Grand Caravan 3.6L Eng Crew Service Manual: 3.6L ENGINE - SERVICE INFORMATION CYLINDER HEAD > CAMSHAFT, ENGINE > REMOVAL > LEFT Fig 1: Magnetic Timing Wheels The magnetic timing

More information

SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES

SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES TEST AND ADJUSTMENT Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking (Minimum).......................... 28 kpa (4 psi) Oil Pressure.....................................

More information

1999 Honda Accord DX

1999 Honda Accord DX Installation 1. Clean tensioner pulleys. Ensure cylinder No. 1 is at TDC by aligning dimple on timing belt drive pulley with pointer on oil pump housing. See Fig. 4. Ensure camshaft pulley TDC marks are

More information

10 +/- 2 degrees before top dead center (BTDC)

10 +/- 2 degrees before top dead center (BTDC) 1996 Ford Contour L4-122 2.0L DOHC VIN 3 SFI Ignition Timing Adjustments Base ignition timing is referenced to the position of the crankshaft position sensor. It is set at 10 +/- 2 degrees before top dead

More information

TIMING BELT REPLACEMENT. Tools Required. J A (KM-421-A) Timing Belt Adjuster J Angle Meter KM-470-B Angular Torque Gage

TIMING BELT REPLACEMENT. Tools Required. J A (KM-421-A) Timing Belt Adjuster J Angle Meter KM-470-B Angular Torque Gage Page 1 of 20 TIMING BELT REPLACEMENT Tools Required J 42492-A (KM-421-A) Timing Belt Adjuster J 45059 Angle Meter KM-470-B Angular Torque Gage Removal Procedure Fig. 37: View Of Throttle Cable CAUTION:

More information

Recommended Installation Procedure Timing Belt Tensioner (979597) 2.0L DOHC, RENAULT F4R Turbo, F4R L DOHC, RENAULT F4P720 (05/18/2004)

Recommended Installation Procedure Timing Belt Tensioner (979597) 2.0L DOHC, RENAULT F4R Turbo, F4R L DOHC, RENAULT F4P720 (05/18/2004) Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must

More information

2006 Expedition/Navigator Workshop Manual

2006 Expedition/Navigator Workshop Manual 7. Remove the RH variable camshaft timing (VCT) oil control solenoid. For additional information, refer to Section 303-14. 8. Remove the RH ignition coils. For additional information, refer to Section

More information

Cylinder Head Replacement

Cylinder Head Replacement CYLINDER HEAD REPLACEMENT (EN... CYLINDER HEAD REPLACEMENT (ENGINE MECHANICAL - 1.6L) Document ID# 1430093 Cylinder Head Replacement Tools Required J 45059 Angle Meter KM-470-B Angular Torque Gauge J 42492-A

More information