Reorder No. EUR07.07

Size: px
Start display at page:

Download "Reorder No. EUR07.07"

Transcription

1 Reorder No. EUR07.07

2

3 The Dynabrade Difference Quality Inside and Out Dynabrade Full Two-Year Warranty Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within two years from the date of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. Any product appearing to be defective must be returned to Dynabrade, freight prepaid, for our inspection. We shall repair or replace at our factory, any equipment or part thereof which shall, within two years after delivery to the original purchaser, indicate upon our examination to have been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations, instructions and safety practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to affect its normal performance. Normally wearable parts such as bearings, rotor blades, etc., are not covered under this warranty. All Dynabrade tools must be used with a filter-regulator-lubricator to maintain all warranties. Tool Maintenance Is Important Air tools do require maintenance to keep them running in tip-top shape. Problems can occur if maintenance is not performed. Moisture can gather in air lines and be blown into air tools during use. Motor lubrication is necessary. Greater performance and longevity of air tools can be expected with the use of a filter-regulatorlubricator. A clean, dry, air source and proper lubrication with a good-grade non-detergent oil (such as Dynabrade Air Lube) is a preventative measure that will go a long way and potentially save on costly repairs. Run Dynabrade air tools at 6.2 Bar (90 PSIG) or less, unless otherwise specified. Running the tools at higher pressures can be the cause of unnecessary premature wear and can contribute to an unsafe condition. Customer Service Dynabrade s customer service staff has one very important job to make sure that you are completely satisfied with your order. Our service department is staffed with highly-trained people, ready to serve you in any way they can, from technical advice and order taking to rush shipments. Dynabrade Tools Meet The Following High Quality Standards Ergonomics and operator comfort have worked their way into each Dynabrade air tool design. Factors including Vacuum, Vibration, Insulation and Sound (VVIS) are addressed at every integral design stage. VVIS is now critical to our research and development of new products as we continue to meet the needs of the marketplace. Vacuum Airborne sanding particles can cause severe inflammation of the eyes and lung tissue, varying on the degree of exposure and the type of airborne contaminants involved. It is because of this danger that Dynabrade manufactures self-generated and central vacuum tools that direct airborne particles away from the operator, air motor and work surfaces. Vibration All hand-held machines transmit vibration to an operator s hand while in operation. Operators that work with vibrating machines for extended periods of time risk many different types of injury. The main types of injuries that are likely to occur are vascular injury, nerve injury, skeletal injury and joint injury. To help reduce vibration, we have built features into our tools that include composite housings, rubber overmolds and insulated handles. Insulation Cold caused by pneumatic-powered tools can cause a variety of work-related injuries. Dynabrade manufactures a variety of tools with thermal-insulated housings to reduce cold air transmission to the operator, reducing the risk of whitefinger disease and other injury-related symptoms. Sound High sound levels over an extended period of time can damage hearing. New enhancements to muffling systems, exhaust protection and other tool design factors further reduce tool sound levels in the workplace. Contact our Luxembourg office for a free demonstration of any Dynabrade tool: (Fax: )

4 TOOLS Table of Contents Categorical Index - In Alphabetical Order Board Sanders Dynaline In-Line Board Sanders...12 General Purpose Tools Cut-Off Wheel Tools...21 Die Grinders...22, 23 Disc Sanders...23 Combination Random Orbital/ Disc Sanders DynaLocke Dual Action Sanders...7 Random Orbital Sanders Dynorbital-Spirit Dynorbital Supreme Scrubber...4 HiVac Dynorbital-Spirit...4 Palm-Style Mini-Dynorbital Sander...20 Right Angle Mini-Orbital Sander...20 Two-Hand Dynorbital Sanders...5 Detailing Tools Dynabuffers...20 Dynafine Detail Sander...11 Dynafine Finger Sander...11 Electric Rotary Right Angle Polisher...18 Palm-Style Mini-Dynorbital Polishers...16 Random Orbital Right Angle Polishers...17 Rotary Right Angle Polishers...15, 16 Dynabug Sanders Snaders Dynabug II Orbital Sanders...14 Dynabug Model T Sanders...13 Dynabug Orbital Sanders...15 Specialty Tools Auto File II Belt Tool...9 DynaZip Surface Preparation Tools...8 Star Sander Kit...23 Wet Sanders Wet Dynabug Model T Sanders...9 Wet Dynafine...10 Wet Dynorbital Supreme Sanders...10 Portable Vacuum Systems Industrial Dry Vacuum with Trolley...24 Gear-Driven Sanders Snaders Two-Hand Gear-Driven Sanders...6 See Page 25 for Accessories Table of Contents

5 TOOLS Numerical Tool Index Model Page Model Page Model Page Model Page Model Page Model Page No. No. No. No. No. No. No. No. No. No. No. No Model Page No. No Model Page No. No Conversion Tables Conversion Factors Length Metres Centimetres Millimetres 1 Inch (in.) m 2.54 cm 25.4 mm 1 Foot (ft.) m cm mm Weight Kilograms Grams 1 Ounce (oz.) kg g 1 Pound (lb.) kg 454 g Volume Litres 1 US Gallon l Torque Newton Metres 1 Ounceinch Nm 1 Poundinch Nm Power Kilowatts Watts 1 hp kw 745 W Most Common Sizes Inches Millimetres Inches Millimetres Inches Millimetres 3/32" 2.5 mm 1/8" 3 mm 3/16" 5 mm 1/4" 6 mm 3/8" 10 mm 1/2" 13 mm 3/4" 19 mm 1" 25 mm 1-1/4" 32 mm 2" 51 mm 4" x 4-5/16" 102 mm x 110 mm 4-1/4" x 4-1/2" 108 mm x 114 mm 2-3/4" x 8" 70 mm x 203 mm 2-3/4" x 11" 70 mm x 279 mm 2-3/4" 70 mm 3" 76 mm 3-1/2" 89 mm 4" 102 mm 4-1/2" 114 mm 5" 127 mm 6" 152 mm 7" 178 mm 8" 203 mm 9" 229 mm 11" 279 mm 12" 305 mm 18" 457 mm 20-1/2" 521 mm 24" 610 mm 30" 762 mm 34" 864 mm 44" 1,118 mm Most Common Rectangular Pad Sizes - Width x Length Inches Millimetres Inches Millimetres 3-2/3" x 7" 93 mm x 178 mm 2-7/8" x 3-1/8" 73 mm x 79 mm 2-3/8" x 3-3/4" 60 mm x 95 mm

6 Dynorbital-Spirit DOUBLE ROW BALANCER BEARING New and innovative bearing seals protect high-quality bearings from sanding residue and reduce bearing temperature for longer bearing life. ERGONOMIC GRIP The shape of the housing conforms to operator s hand for proper wrist position required for greater operator comfort and control. Features and Benefits COMPOSITE LEVER Insulates cold. When the palm-conformed lever is activated, it becomes recessed into the housing thus eliminating a pinch point on the sensitive area of the palm. COMFORT PLATFORM Provides hand and wrist support, as well as increased protection against cold air exhaust. LESS VIBRATION Composite base has integrated full-rubber over-mold creating a non-slip insulated feel. LOW SOUND LEVELS Muffling system reduces sound levels to as low as 78 db(a). Easy to replace muffler inserts. PERFECTLY BALANCED PAD The Best in the Industry! Perfectly-balanced weight-mated pad: the ultimate in swirl-free finishes! 89 mm 80 grams 127 mm 100 grams 152 mm 130 grams CUSTOM-ENGINEERED CYLINDER Custom-engineered, high-strength cylinder provides longer life for less maintenance. ONE-PIECE SPEED CONTROL DIAL Standard on all models. Adjustable side dial maintains user desired speed: variable 4,000-12,000 RPM. LIP-SEAL SHROUD Correct spacing between shroud and pad allows for the most efficient operation of the tool on the work surface. Protects operator from moving sanding pad and enhances dust collection on vacuum models. Patented with patents pending

7 NEW Comfort Platform Now Included on all Palm-Style Dynorbital-Spirit and Dynorbital Supreme Random Orbital Sanders New Comfort Platform provides additional hand and wrist support, further enhancing operator comfort. Offers increased protection against cold air exhaust. Comfort Platform also included on Dynabug II. NEW! NEW! NOTE: Comfort Platform is removable. Patent Pending Order Comfort Platform separately, to install on existing tools Dynorbital-Spirit Color-Coded Levers Quickly Identify your Choice of Three Different Orbits Black lever identifies 2.5 mm (3/32") dia. orbit, used for ultra-fine sanding Features and Benefits Less Weight Non-vacuum model weighs just 0.64 kg (22 oz.), lighter than any other comparable sander. Replacement Drop-In Motor Quick in-house repair lessens downtime. Average repair time, with proper tools, is less than five minutes. See page 45 for details. Grey lever identifies 5 mm (3/16") dia. orbit, used for general sanding Blue lever identifies 10 mm (3/8") dia. orbit, used for aggressive sanding Low Profile Design Only 89 mm (3-1/2") high. Improves control, provides greater operator visibility and allows pad to be used flat on work surface for better finishes. More Power True 12,000 RPM air motor has more power. The floating rotor utilizes five blades producing more usable power (186 W [.25 hp]). Highstrength, composite rotor is stronger and has better lubricating qualities allowing the blades to wear longer. As a result, less air (14 SCFM/396 LPM) is used more efficiently to maintain maximum power. Identification Marking Easy to read model number and serial number markings located on the side of the tool. 2

8 Dynorbital-Spirit The lightest tool on the market today! Ideal for achieving a swirl-free finish on paint and other surfaces. Incorporates the latest engineering and manufacturing technology to create the lightest sander on the market today. Non-vacuum model weighs just 0.64 kg (22 oz.). This makes the Dynorbital-Spirit ideal for all vertical applications. Innovative bearing seals Innovative V-Seal bearing seal (patent pending) protects balancer shaft bearing from sanding residue for longer life. Unique top hat seal protects front motor bearing from sanding residue. Also holds in bearing lubrication while keeping out other contaminants. Sanding Pads All models feature our premium weight-mated, hook-face sanding pad. See pages for optional pad choices. Vinyl-face pads available upon request only. Optional Accessory Brush Ring Part Number See page 45. Non-Vacuum Optional vacuum conversion kits available to easily convert non-vacuum tool to self-generated vacuum tool for connection to a self-contained dust collection system. Can also be converted to connect to a standard central vacuum system. Model Pad Diameter 2.5 mm (3/32") Orbit Models (Pad) 5 mm (3/16") Orbit Models (Pad) 10 mm (3/8") Orbit Models (Pad) 76 mm (3") (56087) (56087) (56087) 89 mm (3-1/2") (54313) (54313) (54313) 127 mm (5") (54325) (54325) (54325) 152 mm (6") (54327) (54327) (54327) Self-Generated Vacuum Includes portable self-contained dust collection system (part number 50617). Model Pad Diameter 2.5 mm (3/32") Orbit Models (Pad) 5 mm (3/16") Orbit Models (Pad) 10 mm (3/8") Orbit Models (Pad) 76 mm (3") (56087) (56087) (56087) 89 mm (3-1/2") (54313) (54313) (54313) 127 mm (5") (54326) (54326) (54326) 152 mm (6") (54328) (54328) (54328) Central Vacuum Has 25 mm (1") dia. vacuum port for easy central vacuum hook-up. Pad Diameter 2.5 mm (3/32") Orbit Models (Pad) 5 mm (3/16") Orbit Models (Pad) 10 mm (3/8") Orbit Models (Pad) 76 mm (3") (56087) (56087) (56087) Model mm (3-1/2") (54313) (54313) (54313) 127 mm (5") (54326) (54326) (54326) 152 mm (6") (54328) (54328) (54328) Model Motor Motor Sound Air Flow Rate Air Pressure Air Inlet Hose Size Spindle Weight Length Height Number W (hp) RPM Level CFM/SCFM (LPM) Bar (PSIG) Thread mm (Inch) Thread kg (lb.) mm (Inch) mm (Inch) Non-Vacuum 186 (.25) 12, db(a) 2/14 (396) 6.2 (90) 1/4" NPT 8 (1/4) 5/16"-24 female 0.6 (1.5) (6) 89 (3-1/2) Vacuum 186 (.25) 12, db(a) 2/14 (396) 6.2 (90) 1/4" NPT 8 (1/4) 5/16"-24 female 0.7 (1.5) (9) 89 (3-1/2) 3

9 HiVac Dynorbital-Spirit The combination of our unique shroud design and 3-hole sanding pad provide enhanced collection of dust and debris. The random orbital action enables operator to achieve swirl-free finishes. Comfortable tool weight of only 0.6 kg (20.8 oz.) minimizes operator fatigue. Innovative V-Seal bearing protects balancer shaft from sanding residue for longer tool life. Unique top hat seal protects front motor bearing from contaminants while maintaining bearing lubrication. Tool has 25 mm (1") diameter vacuum port and accepts 76 mm (3") diameter sanding pads. See page 37 for sanding pad options. Model NEW! NEW! Self-Generated Vacuum Orbit Diameter Model Number (Hook-Face Pad) 2.5 mm (3/32") (56144) 5 mm (3/16") (56144) Central Vacuum Orbit Diameter Model Number (Hook-Face Pad) 2.5 mm (3/32") (56144) 5 mm (3/16") (56144) Model Model mm (3/16") Orbit for general sanding 2.5 mm (3/32") Orbit for ultra-fine sanding Model Motor Motor Max. Air Flow Spindle Air Pressure Hose I.D. Size Air Inlet Weight Length Height Number W (hp) RPM CFM/SCFM (LPM) Thread Bar (PSIG) mm (Inch) Thread kg (lb.) mm (Inch) mm (Inch) 21068/ (.25) 12,000 2/14 (396) 5/16" (90) 8 (1/4) 1/4" NPT 1.3 (0.6) 197 (7-3/4) 95 (3-3/4) 21070/ (.25) 12,000 2/14 (396) 5/16" (90) 8 (1/4) 1/4" NPT 1.3 (0.6) 166 (6-1/2) 95 (3-3/4) Dynorbital Model Excellent tool for detail shops. Use with shampoo or cleaner to power out dirt and stains. Random orbital 10,000 RPM action allows brush bristles to loosen trapped dirt particles. Adjustable speed control. Helps to restore matted carpet fibers. Rejuvenate worn and dirty interiors. Random orbital agitation action makes the difference in deep cleaning carpets, floor mats, seats (cloth, leather, vinyl), trunk areas, tires and convertible tops. Tool includes Brush Holder, Short-Nap 89 mm (3-1/2") Cleaning Brush (13 mm [1/2"] thick) and Long-Nap 89 mm (3-1/2") Cleaning Brush (22 mm [7/8"] thick). Supreme Scrubber 5 mm (3/16") Orbit Model Brush Holder Short-Nap Brush Long-Nap Brush Model Motor Motor Sound Air Flow Rate Air Inlet Hose Size Air Pressure Weight Length Height Number W (hp) RPM Level CFM/SCFM (LPM) Thread mm (Inch) Bar (PSIG) kg (lb.) mm (Inch) mm (.24) 10, db(a) 2/16 (453) 1/4" NPT 10 (3/8) 6.2 (90) 1.0 (0.5) 136 (5-3/8) 89 (3-1/2) 4

10 Two-Hand Dynorbital Sanders Composite tool housing and handle create non-slip feel and reduce cold air transmission to operator. Adjustable speed control. All models feature our premium weight-mated, hook-face sanding pad. See page for optional pad choices. Long handle provides excellent comfort and control, especially when working on vertical sides of workpiece. 10 mm (3/8") Orbit 5 mm (3/16") Orbit for aggressive sanding for general sanding Non-Vacuum 127 mm (5") and 152 mm (6") models are 12,000 RPM. Pads have 5/16"-24 male spindle. 203 mm (8") models are 10,000 RPM. Pads mount with 5 screws. Pad 5 mm (3/16") Orbit 10 mm (3/8") Orbit Diameter Models (Pad) Models (Pad) 127 mm (5") (54325) (54325) Model mm (6") (54327) (54327) 203 mm (8") (56236) N/A Self-Generated Vacuum Self-generated vacuum models are ready for connection to portable dust collection systems. Models can also be connected to standard central vacuum systems. Vacuum port accepts 32 mm (1-1/4") diameter hose cuff for increased vacuum flow (no overskirt shroud is included). Model Pad 5 mm (3/16") Orbit 10 mm (3/8") Orbit Diameter Models (Pad) Models (Pad) 127 mm (5") (54326) (54326) 152 mm (6") (54328) (54328) 203 mm (8") (56237) N/A Central Vacuum Ready for hook-up to standard central vacuum systems. All models include combination lip seal/overskirt shroud, which offers enhanced vacuum capability and greater workpiece visibility. Vacuum port accepts 25 mm (1") diameter hose cuff on the 152 mm (6") models, and 51 mm (2") diameter hose cuff on the 203 mm (8") model. Pad 5 mm (3/16") Orbit 10 mm (3/8") Orbit Diameter Models (Pad) Models (Pad) 152 mm (6") (54328) (54328) 203 mm (8") (56237) N/A Model Pad Motor Motor Sound Air Flow Rate Air Inlet Hose Size Air Pressure Weight Length Height Diameter W (hp) RPM Level CFM/SCFM (LPM) Thread Size Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) 127 mm/152 mm (5"/6") 336 (.45) 12, db(a) 3/23 (651) 1/4" NPT 6 (1/4) 6.2 (90) 1.3 (2.9) 267 (10-1/2) 114 (4-1/2) 203 mm (8") 336 (.45) 10, db(a) 3/23 (651) 1/4" NPT 10 (3/8) 6.2 (90) 1.5 (3.3) 305 (12) 114 (4-1/2) 5

11 Two-Hand Gear-Driven Sanders Shaves and Levels Body Filler Fast Long handle provides excellent comfort and control, especially when working on vertical sides of vehicles. Adjustable speed control. Composite housing reduces weight and protects against cold air transmission to operator s hands. Includes hook-face sanding pad that is perfectly balanced and weight-mated for smooth performance. Vinyl-face pads available upon request only. See pages for optional pad choices. Non-Vacuum Pad Diameter Model Number (Hook-Face Pad) 152 mm (6") (57764) 203 mm (8") (56236) Model Model Unique cutting action is specific to Two-Hand Gear-Driven Sanders for quick and efficient filler removal Central Vacuum Designed for exclusive use with central vacuum system. Combination lip-seal shroud/overskirt allows operator greater workpiece visibility and enhanced vacuum capability. Dust is extracted away from air motor (reducing contamination) for a smoother, easier path of extraction. Anti-clog design is advantageous when sanding damp filler material. 152 mm (6") diameter models have 25 mm (1") dia. vacuum port; 203 mm (8") diameter model has 51 mm (2") dia. vacuum port. Model Pad Diameter Model Number (Hook-Face Pad) 152 mm (6") (57765) 203 mm (8") (56237) Model Model Motor Motor Pad Dia. Sound Air Flow Rate Air Inlet Air Pressure Weight Length Height Number W (hp) RPM mm (Inch) Level CFM/SCFM (LPM) Thread Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) 10760/ (.45) (6) 91 db(a) 3/23 (651) 1/4" NPT 6.2 (90) 1.7 (3.7) 293 (11-1/2) 143 (5-5/8) 10763/ (.45) (8) 87 db(a) 3/23 (651) 1/4" NPT 6.2 (90) 1.9 (4.2) 318 (12-1/2) 143 (5-5/8) 6

12 DynaLocke A True Rotary Disc and Random Orbital Sander in One Ideal for paint stripping and blending. Very lightweight with ultra-smooth sanding performance. Recessed switch allows easy change from rotary to random orbital action with the turn of a dial. Includes hook-face sanding pad that is perfectly balanced and weight-mated for smooth performance. Dual Action Sanders Non-Vacuum Model Pad Model Number Diameter (Hook-Face Pad) 76 mm (3") (56087) 89 mm (3-1/2") (54313) 127 mm (5") (54325) 152 mm (6") (54327) Model Self-Generated Vacuum Self-generated vacuum models are ready for connection to portable dust collection systems (optional). Models can also be connected to standard central vacuum systems. Vacuum port accepts 32 mm (1-1/4") diameter hose cuff for increased vacuum flow (no overskirt shroud is included). Designed to vacuum in random orbital mode only. Pad Model Number Diameter (Hook-Face Pad) 76 mm (3") (56087) 89 mm (3-1/2") (54313) 127 mm (5") (54326) 152 mm (6") (54328) Model Dial switch allows for easy change-over from random orbital to rotary action BRING THE TOOL TO A COMPLETE STOP BEFORE SWITCHING MODES RANDOM ORBITAL SANDER 5 mm Orbit Featheredge & Finesse Body Panels! DISC SANDER Strip, Level and Grind to Bare Metal! Rotary Motion Model Motor Motor Sound Air Flow Rate Air Inlet Hose Size Air Pressure Weight Length Height Description W (hp) RPM Level CFM/SCFM (LPM) Thread mm (Inch) Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) 76 mm (3") Models 336 (.45) 12, db(a) 3/23 (651) 1/4" NPT 6 (1/4) 6.2 (90) 1.0 (2.2) 263 (10-3/8) 137 (5-3/8) 89 mm (3-1/2") Models 336 (.45) 12, db(a) 3/23 (651) 1/4" NPT 6 (1/4) 6.2 (90) 1.0 (2.2) 263 (10-3/8) 137 (5-3/8) 127 mm (5") Models 336 (.45) 12, db(a) 3/23 (651) 1/4" NPT 6 (1/4) 6.2 (90) 1.1 (2.4) 280 (11) 131 (5-1/8) 152 mm (6") Models 336 (.45) 12, db(a) 3/23 (651) 1/4" NPT 6 (1/4) 6.2 (90) 1.3 (2.9) 293 (11-1/2) 131 (5-1/8) 7

13 DynaZip Surface Preparation Tools DynaZip Air Tool Model Tool with Wire Wheel Excellent power and torque for effectively removing seam sealer, rust proofing, chip guard, paint and surface rust in common and tight areas. Dramatically outperforms conventional spiral-wound wire wheels without clogging. Tool duplicates sand-blasting effect without surface fatigue and provides ultimate contour adaptation. Quick and easy accessory change. Includes tool with wheel guard and handle. Also includes Wire Wheel (102 mm dia. x 19 mm wide) and Hub Assembly. (Hub Assembly includes bolt, hub shield, hub cushion and drive plates for mounting either Wire Wheel or Eraser Wheel.) See page 47 for optional accessories Tool Only Tool with wheel guard and handle only; no accessories. Model DynaZip-Eraser Decal Removal Tool Model Excellent for removing two-sided adhesive molding tape and working on metal surfaces. Superior performance versus conventional solid or doughnut-type wheel erasers with no paint damage. Wheel has crepe teeth serrations for improved cooling effect air flow. Resists heat buildup and prevents jumping or vibrations. Includes tool with wheel guard and handle. Also includes Eraser Wheel (102 mm dia. 30 mm wide) and Hub Assembly. (Hub Assembly includes bolt, hub shield, hub cushion and drive plates for mounting either Wire Wheel or Eraser Wheel.) See page 47 for optional accessories. Model DynaZip Versatility Kit Model DynaZip tool Coarse Wire Wheel (13 mm [1/2"] wire bristle width x 19 mm [3/4"] wide band) Coarse Wire Wheel (19 mm [3/4"] wire bristle width x 19 mm [3/4"] wide band) Eraser Wheel Wheel Hub Assembly Model Model Motor Motor Sound Spindle Air Flow Rate Air Inlet Hose Size Air Pressure Weight Length Height Number W (hp) RPM Level Thread CFM/SCFM (LPM) Thread mm (Inch) Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) All Models 298 (.4) 3, db(a) 1/4"-20 Male 3/28 (793) 1/4" NPT 10 (3/8) 6.2 (90) 1.1 (2.4) 305 (12) 140 (5-1/2) 8

14 Auto File II Belt Tool Model mm (5/8") or 19 mm (3/4") Wide Excellent multi-purpose tool for grinding sharp metal edges, rusted bolts, welds, etc. Works well on composites, blending, scuffing grooves and contours. Reach drip rails in auto trunks. Grinding head pivots and can be set to any position. Includes Contact Arm for 16 mm (5/8") or 19 mm (3/4") wide abrasive belts is the only arm compatible with 520 mm (20-1/2") long belts. Model Four-In-One Versatility Kit Kit Model ,000 RPM. 1/4" die grinder, 76 mm (3") cut-off tool, belt sander, and 76 mm (3") disc sander. Quick and convenient, easy to change accessories. A must for all shops. Includes: basic tool; 6 mm collet; cut-off guard; flange; 76 mm (3") backing pad; drive wheel; belt housing assembly; contact arm assembly; Dynaswivel ; wrenches for accessory changes; sample abrasive belt and 76 mm (3") abrasive disc; deluxe storage/carry case. Wet Dynabug Model Model mm (5") Diameter 152 mm (6") Diameter Includes 127 mm (5") dia. Includes 152 mm (6") dia. hook-face pad and soft hook-face pad and soft interface pad. interface pad. Excellent on Primer and Clear Coat Fast, smooth and uniform surface preparation; reduced labor time; never needs oil. Fingertip control valve allows for precise water flow. Our unique water feed through-the-pad design allows use of standard round wet paper with holes. No special sand paper or hole punch needed. Up to 5 mm (3/16") dia. orbital action with adjustable speed control. Includes soft interface pad for contours and all hardware for self-siphoning with 5 m (20') of water hose. Pad Diameter Model Number (Hook-Face Pad) Interface Pad 127 mm (5") (58086) mm (6") (58093) Model Motor Motor Sound Air Flow Rate Air Inlet Hose Size Air Pressure Weight Length Height Number W (hp) RPM Level CFM/SCFM (LPM) Thread mm (Inch) Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) (.5) 20, db(a) 3/22 (623) 1/4" NPT 10 (3/8) 6.2 (90) 1.3 (2.9) 381 (15) 127 (5) Model T Sanders Model Model Motor Motor Pad Diameter Sound Air Flow Rate Air Inlet Air Pressure Weight Length Height Number W (hp) RPM mm (Inch) Level CFM/SCFM (LPM) Thread Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) 10288/10289 N/A 20, (5-6) 72 db(a) 2/17 (481) 1/4" NPT 6.2 (90) 0.7 (1.5) 203 (8) 102 (4)

15 Wet Dynorbital Supreme Sanders A Better Way to a Consistent Finish! Achieve a uniform and consistent finish faster and easier than before; remove runs, sags, orange peel, dust nibs and other imperfections. Adjustable speed control. Includes: air and water connections (shown below photo), hook-face pad and overskirt shroud to control water splash. Hook-up to garden hose or optional Portable Wet Tank. See page 36 for optional pad choices. Pad 2.5 mm (3/32") Orbit 5 mm (3/16") Orbit Diameter Models (Pad) Models (Pad) 89 mm (3-1/2") (54313) (54313) 127 mm (5") (54325) (54325) 152 mm (6") (54327) (54327) Model TWO-WAY WATER VALVE Push the button as desired, or... lock the valve in place for desired water flow rate! 2.5 mm (3/32") Orbit for ultra-fine sanding 5 mm (3/16") Orbit for general sanding A INCLUDED AIR AND WATER CONNECTIONS C B D E A = " Hose Bib Fitting B = /8" Quick Disconnect Fitting C = 1/4" NPT female air supply connection D = Air Line (1/4" dia.) E = Overhose Model Motor Motor Pad Diameter Sound Air Flow Rate Air Inlet Air Pressure Weight Length Height Number W (hp) RPM mm (Inch) Level CFM/SCFM (LPM) Thread Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) 10341/ (.24) 10, (3-1/2) 76 db(a) 2/16 (453) 1/4" NPT 6.2 (90) 1.0 (2.1) 152 (6) 95 (3-3/4) 10343/ (.24) 10, (5) 77 db(a) 2/16 (453) 1/4" NPT 6.2 (90) 1.0 (2.1) 165 (6-1/2) 92 (3-5/8) 10345/ (.24) 10, (6) 74 db(a) 2/16 (453) 1/4" NPT 6.2 (90) 1.0 (2.2) 178 (7) 89 (3-1/2) Wet Dynafine Model ,000 RPM All-in-One Misting System helps flush abrasive to achieve a consistent, repeatable finish. Ergonomic 7 offset and low-vibration design allow for greater operator comfort and control. Accepts 51 mm (2") and 76 mm (3") dia. vinyl or hook-face sanding pads. One vinyl-face pad of each diameter is included with tool. See page 43 for optional pads. Includes 910 mm (3') water line with Male Quick Disconnect fitting. Model Model Motor Motor Pad Diameter Sound Air Flow Rate Air Inlet Air Pressure Weight Length Height Number W (hp) RPM mm (Inch) Level CFM/SCFM (LPM) Thread Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) (.15) 13, (2-3) 65 db(a) 3/20 (566) 1/4" NPT 6.2 (90) 0.8 (1.8) 229 (9) 95 (3-3/4) 10

16 Dynafine Finger Sander Model Tiny 0.8 mm (1/32") diameter orbital action for fine finishes. Eliminate tedious hand sanding. Lightweight... only 0.7 kg (1.6 lbs.). Excellent for use on edges, corners and hard-to-reach areas. Eliminate wrapping sand paper around paint sticks, let the tool do the work. Includes tool with Sanding Arm, sample platen pads and sample abrasive strips. Model Deluxe Versatility Kit Includes: tool, and Sanding Arms; hook-face and vinyl-face pads; abrasive strip assortment. Abrasive Strips Sanding Arm Dynafine Detail Sander Model Features 0.8 mm (1/32") dia. orbital action for a superior finish. Insulated composite handle is offset for operator comfort and may be adjusted for left or right-handed users. Includes composite Dynaswivel flow-control speed regulator and both triangular and tear-drop shaped hook-face pads. See page 43 for optional pads. Uses reattachable and PSA-mounted (pressure-sensitive adhesive), coated non-woven nylon and sponge abrasives Versatility Kit Includes tool with hook-face and PSA pads and an assortment of coated hook-face, non-woven nylon and sponge abrasives. Model Model Motor Motor Sound Air Flow Rate Air Inlet Hose Size Air Pressure Weight Length Height Number W (hp) RPM Level CFM/SCFM (LPM) Thread mm (Inch) Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) 10800/ (.15) 13, db(a) 3/20 (566) 1/4" NPT 6 (1/4) 6.2 (90) 0.7 (1.5) 298 (11-5/8) 102 (4) 11

17 Dynaline In-Line Board Sanders Ideal for areas where a conventional long board sander is too big. Tool has precision gear-set for smooth, controlled, unstoppable sanding power; always a consistent sanding stroke. Adjustable speed control. Mount reattachable abrasive sheets to short-nap hook-face pad included with tool. See page 42 for optional pad choices. Non-Vacuum Model Pad can be set and locked to any 360 position. Optional 93 mm (3-2/3") wide x 178 mm (7") long and 70 mm (2-3/4") wide x 279 mm (11") long pads available (see page 40). Model Pad Dimensions mm (Inch) Model Number (Hook-Face Pad) 70 (2-3/4) W x 203 (8) L (57456) Central Vacuum Model Tool has 25 mm (1") exhaust port ready to connect to your central vacuum system or shop vac. Punch plates are available to convert abrasive to vacuum paper, see right. Pad Dimensions mm (Inch) Model Number (Hook-Face Pad) 70 (2-3/4) W x 203 (8) L (57457) Optional Accessory Loop-Face Pad Part Number Compatible with 3M Hookit II abrasives. See page 42. Optional Accessories Punch Plate Part Number mm (3-7/8") wide x 178 mm (7") long Punch Plate for converting non-vac to vacuum paper. Specialty Pads Vinyl-face; accepts 70 mm (2-3/4") wide x 203 mm (8") long PSA abrasive sheets. Part Number Part Number Curved pad. Radiused pad. Model Motor Strokes Strokes Sound Air Flow Rate Air Inlet Hose Size Air Pressure Weight Length Height Number W (hp) mm (Inch) per Minute Level CFM/SCFM (LPM) Thread mm (Inch) Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) 10400/ (.25) 10 (3/8) 2, db(a) 3/18 (510) 1/4" NPT 6 (1/4) 6.2 (90) 1.2 (2.6) 178 (7) 95 (3-3/4) Dynaline In-Line 279 mm (11") Board Sander Model Insulated longer handle for added control and stability. Sanding pad may be rotated 360 and set and locked to any comfortable position. Includes 70 mm (2-3/4") wide x 279 mm (11") long, premium urethane PSA sanding pad with clips (57512). 93 mm (3-2/3") wide x 178 mm (7") long and 70 mm (2-3/4") wide x 203 mm (8") long pads may also be used. See pages 42 for optional pad choices. For use with hook-face and PSA coated abrasives Kit Includes tool with 70 mm (2-3/4") wide x 279 mm (11") long, premium urethane PSA pad with clips (57512), and hook-face pad (57513) with sample abrasives. Model Model Motor Stroke Strokes Sound Air Flow Rate Air Inlet Hose Size Air Pressure Weight Length Height Number W (hp) mm (Inch) Per Minute Level CFM/SCFM (LPM) Thread mm (Inch) Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) (.25) 10 (3/8) 2, db(a) 3/18 (510) 1/4" NPT 6 (1/4) 6.2 (90) 1.4 (3.1) 279 (11) 95 (3-3/4) 12

18 Dynabug Weighs Only 0.5 kg (1.1 lbs.) Requires No Air Tool Oil Great For Color Sanding Up to 5 mm (3/16") dia. orbital action - the faster the sander runs, the more aggressive the cutting action. 20,000 RPM. Adjustable speed control. Base plate is hook-face to accept interface pads. No tools required to change pads on all models. Uses hook-face and vinyl-face abrasive sheets and discs. All models include 910 mm (3') of lightweight, flexible air hose. Non-Vacuum Model T Sanders Pad Dimensions mm (Inch) Clips Model Number (Hook-Face Pad) Model Number (Vinyl-Face Pad) 102 (4) W x 110 (4-1/4) L Yes (57999) 108 (4-1/4) W x 114 (4-1/2) L No (57998) (56244) 127 (5) No (56248) (56249) Model (6) No (56268) (56269) NOTE: Clips are good for 228 mm (9") wide x 279 mm (11") long sheet paper cut in four, or 152 mm (6") disc will fit, too. Model Central Vacuum Ready for hook-up to central vac system or our portable vacuum systems. Both models have 25 mm (1") diameter exhaust port for vacuum hose hook-up. Pad Dimensions Model Number Model Number mm (Inch) Clips (Hook-Face Pad) (Vinyl-Face Pad) 108 (4-1/4) W x 114 (4-1/2) L No (56285) (56286) Model Model Model Model Motor Sound Air Flow Rate Air Inlet Hose Size Air Pressure Weight Length Height Description RPM Level CFM/SCFM Thread mm (Inch) Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) All Models 20, db(a) 1/9 (255) 1/4" NPT 6 (1/4) 6.2 (90) 0.5 (1.1) 127 (5) 76 (3)

19 Dynabug II Orbital Sanders Designed for efficient finishing of composites, painted and metal surfaces. Compact size and light weight allows comfortable use in small spaces. 2.5 mm (3/32") orbit produces a smooth finish. Non-Vacuum Includes hook-face sanding pad for optional hook-face abrasive sheets. Model Model Includes Sanding Pad, 74 mm (3") W x 109 mm (4-1/4") L. Model Includes Sanding Pad, 80 mm (3-1/4") W x 130 mm (5") L. Central Vacuum Tool has 25 mm (1") diameter vacuum port, ready for connection to external vacuum source. Includes hook-face sanding pad for optional hook-face, vacuum abrasive sheets. Model Model Includes Vacuum Sanding Pad, 74 mm (3") W x 109 mm (4-1/4") L. NEW! NEW! Model Model Includes Vacuum Sanding Pad, 80 mm wide by 130 mm long (approximately 3-1/4" x 5"), with eight vacuum holes. Model Includes Loop-Face Vacuum Sanding Pad, 68 mm (2-3/4") W x 196 mm (7-3/4") long, with eight vacuum holes. Loop-Face Pad Part Number Compatible with 3M Hookit II abrasives. See page 41. Model Delta Style Includes Delta Style Vacuum Sanding Pad, 99 mm wide (at wider end) by 143 mm long (approximately 4" x 5-3/4"), with seven vacuum holes. Unique pad has curved edges for sanding rounded areas, and pointed tip for reaching into tight corners. NEW! NEW! NEW! Model Model Vacuum Motor Motor Air Flow Rate Hose Size Air Inlet Air Pressure Weight Length Height Number Type W (hp) RPM CFM/SCFM (LPM) mm (Inch) Thread Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) Non-Vacuum 112 (.15) 10,000 2/13 (368) 6 (1/4) 1/4" NPT 6.2 (90) 0.8 (1.8) 216 (8-1/2) 89 (3-1/2) Central Vacuum 112 (.15) 10,000 2/13 (368) 6 (1/4) 1/4" NPT 6.2 (90) 0.7 (1.5) 146 (5-3/4) 89 (3-1/2) Non-Vacuum 112 (.15) 10,000 2/13 (368) 6 (1/4) 1/4" NPT 6.2 (90) 0.8 (1.8) 216 (8-1/2) 89 (3-1/2) Central Vacuum 112 (.15) 10,000 2/13 (368) 6 (1/4) 1/4" NPT 6.2 (90) 0.7 (1.5) 146 (5-3/4) 89 (3-1/2) Central Vacuum 112 (.15) 10,000 2/13 (368) 6 (1/4) 1/4" NPT 6.2 (90) 0.8 (1.7) 216 (8-1/2) 89 (3-1/2) Central Vacuum 112 (.15) 10,000 2/13 (368) 6 (1/4) 1/4" NPT 6.2 (90).7 (1.6) 222 (8-3/4) 89 (3-1/2) 14

20 Dynabug Orbital Sanders Smooth, quiet-running tool is ideal for blocking and flat sanding. Every model has a standard 2.5 mm (3/32") orbit pattern which provides the very best finish. Spring clips standard on all models. Includes vinyl-face sanding pad. See page 41 for optional pad choices. 93 mm (3-2/3") wide x 178 mm (7") long abrasive sheet fits pad area. Use 93 mm (3-2/3") x 229 mm (9") paper when securing the paper to the built-in clips. Central vacuum model has 25 mm (1") dia. vacuum port for easy central vacuum hose hookup. Model ,5 mm (3/32") Orbit Pattern Vacuum Type Model Number (Vinyl-Face Pad) Non-Vacuum (57850) Central Vacuum (57855) Optional Accessories Punch Plate Part Number mm (3-7/8") wide x 178 mm (7") long Punch Plate for converting non-vac to vacuum paper. Model Model Motor Motor Air Flow Rate Hose Size Air Inlet Air Pressure Weight Length Height Number W (hp) RPM CFM/SCFM (LPM) mm (Inch) Thread Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) 10170/ (.25) 10,000 2/16 (453) 6 (1/4) 1/4" NPT 6.2 (90) 1.2 (2.6) 184 (7-1/4) 108 (4-1/4) Rotary Right Angle Polishers 76 mm (3") Diameter Model Model ,300 RPM 3,200 RPM Excellent tool for spot repair and buffing/polishing. Angle-head design permits access to difficult areas. Replacement buffing pads available. Composite grip absorbs vibration and reduces cold air transmission to the operator. Built-in speed control, rear exhaust, safety-lock lever throttle. Includes Back-Up Pad (76 mm [3"] dia. hook-face) and Wool Buff (89 mm [3-1/2] dia.). Model Versatility Kit Includes 2,300 RPM tool, hook-face backing pad, terry cloth bonnet, synthetic and natural wool pads, white polishing and yellow cutting foam pads, Dynabrade Finesse Creme and Glaze, random orbital sanding head, sanding pad, sample 9-micron abrasive discs, Dynaswivel, deluxe storage/carry case and wrenches for accessory changes. Model Model Motor Motor Sound Maximum Air Flow Hose Size Air Pressure Spindle Weight Length Height Number W (hp) RPM Level CFM/SCFM (LPM) mm (Inch) Bar (PSIG) Thread kg (lb.) mm (Inch) mm (Inch) (.4) 2, db(a) 4/28 (793) 10 (3/8) 6.2 (90) 3/8"-24 male 0.9 (2.0) 264 (10-3/8) 64 (2-1/2) (.4) 3, db(a) 4/28 (793) 10 (3/8) 6.2 (90) 3/8"-24 male 0.9 (2.0) 264 (10-3/8) 64 (2-1/2) Additional Specifications: Air Inlet Thread 1/4" NPT 15

21 Palm-Style Mini-Dynorbital 76 mm 127 mm (3"-5") Diameter Model Model mm (3") diameter 127 mm (5") diameter Compact size, excellent power to buff and polish motorcycle gas tanks and helmets, small parts, side view mirrors and bumpers. Does the work where full-size polishers are too big. Geared rotary action; rear exhaust motor with speed control. Use Dynabrade Finesse Creme and Glaze for superior gloss finishes after compounding. Non-Vacuum Pad Model Number Sample Pad Diameter (Hook-Face Pad) (Description) 76 mm (3") (50125) (Terry) (Wool) 127 mm (5") (50146) (Foam Polishing) Model Model Polishers 76 mm Three-in-One Versatility Kit Kit 76 mm (3") polisher, 76 mm (3") rotary sander, 32 mm (1-1/4") dust nib remover - all in one! Remove dust nibs and scratches on base coat/clear coat. Includes all you need for quick, simple spot repair on painted surfaces: basic tool, hook-face backing pad, medium 32 mm (1-1/4") dia. and 89 mm (3-1/2") dia. vinyl-face pads, mini-orbital head, sample 9-micron micro-finishing film discs, sample abrasive pack, 76 mm (3") dia. terry cloth and wool bonnets, 76 mm (3") dia. foam waffle pad, Dynabrade Finesse-It Creme, Dynabrade Glaze and wrenches for pad changes. Model Motor Sound Spindle Air Flow Rate Air Inlet Hose Size Air Pressure Weight Length Height Number RPM Level Thread CFM/SCFM (LPM) Thread mm (Inch) Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) 10390/ , db(a) 1/4"-20 male 3/18 (510) 1/4" NPT 6 (1/4) 6.2 (90) 0.9 (2.0) 137 (5-1/2) 108 (4-1/4) Rotary Right Angle Polishers 127 mm 203 mm (5" 8") Diameter Model Model /8"-11 male spindle M14 x 2 male spindle 0-2,500 RPM free speed. Uses 127 mm (5") to 203 mm (8") dia. buffs. Insulated handle absorbs vibration and reduces cold air transmission to the operator. Compact and lightweight design. Rear exhaust, variable speed safety-lock lever throttle. Soft-grip handle can be positioned for right or left hand operation. Order or Hook-Face Backing Pad and Foam Buff separately, see page 32. MUCH LIGHTER THAN ELECTRIC POLISHERS! Model Model Motor Motor Sound Maximum Air Flow Hose Size Air Pressure Spindle Weight Length Height Number W (hp) RPM Level CFM/SCFM (LPM) mm (Inch) Bar (PSIG) Thread kg (lb.) mm (Inch) mm (Inch) (.7) 0-2, db(a) 3/27 (765) 10 (3/8) 6.2 (90) 5/8"-11 Male 2.4 (5.3) 305 (12) 102 (4) (.7) 0-2, db(a) 3/27 (765) 10 (3/8) 6.2 (90) M14x2 Male 2.4 (5.3) 305 (12) 102 (4) Additional Specifications: Air Inlet Thread 1/4" NPT 16

22 Random Orbital Right Angle Polishers 178 mm 203 mm (7" 8") Diameter Model Model M14 x 2 male spindle 5/8"-11 male spindle Unique random orbital motion minimizes haze and halo effects while preventing burn through of top coats and sealants. No haze, no halo, no swirls. Innovative polishing head (patent pending) with streamlined, lightweight design for maximum operator comfort. Includes 178 mm (7") diameter backing pad (P/N 50855); polishing and cutting pads sold separately. Model mm (3/4") Orbit Model Model Motor Motor Sound Maximum Air Flow Hose Size Air Pressure Spindle Weight Length Height Number W (hp) RPM Level CFM/SCFM (LPM) mm (Inch) Bar (PSIG) Thread kg (lb.) mm (Inch) mm (Inch) (.7) 2, db(a) 4/27 (765) 10 (3/8) 6.2 (90) M14x2 Male 2.9 (6.4) 366 (14-3/8) 136 (5-3/8) (.7) 2, db(a) 4/27 (765) 10 (3/8) 6.2 (90) 5/8"-11 Male 2.9 (6.4) 366 (14-3/8) 136 (5-3/8) Additional Specifications: Air Inlet Thread 1/4" NPT Random Orbital Head Kit Convert Standard Rotary Tool into Random Orbital Polisher Model Model M14 x 2 male spindle 5/8"-11 male spindle For mounting to tool motors up to 3,200 RPM. Can be used with foam, wool and terry polishing pads. Kit includes: random orbital polishing head (patent pending); 178 mm (7") diameter hook-face backing pad and natural sheepskin polishing pad; 26 mm wrench. NEW! NEW! 19 mm (3/4") Orbit 17

23 Electric Rotary Right Angle Polisher 178 mm (7") Diameter Model ,800 RPM Excellent for polishing applications. Tool includes variable speed trigger and electronic speed regulator. Regulator adjusts tool speed from 800 to 1,800 RPM and locks in constant speed while tool is in use. Accepts 178 mm (7") dia. foam and wool buffs or polishing bonnets. Electrical tool is double-insulated (Class II) for safety. Quick and easy change of replacement brushes for reduced downtime. Tool spindle locks in place for efficient changing of pad or bonnet. Lightweight tool can be comfortably used in horizontal or vertical applications. Side handle attaches for left or right handed use. Model Included Accessory Bow-Type Handle Part Number See page 45. Model Model Motor Motor Disc Diameter Spindle Weight Length Height Number W RPM mm (Inch) Voltage Frequency Thread kg (lb.) mm (Inch) mm (Inch) , , (7) 230V 50Hz M14 x (4.2) 292 (11-1/2) 136 (5-3/8) Polishing Starter Kit Part Number mm (3") Diameter Excellent starter kit for rapid and efficient refresh on two-wheelers (motorcycles, scooters, etc.). Ideal for buffing and polishing painted Before surfaces (e.g., gas tanks), alloys, aluminium and chromium surfaces. Removes scratch marks, oxidation traces, dust and grime, flies and insects; restores faded colors with a high gloss finish. Includes Model 18055, 76 mm (3") Right Angle Polisher (2,300 RPM), hook-face backing pad, Dynabrade After Finesse Sanding Creme and Dynabrade Glaze (118 ml. [4 oz.] each), Dynabrade ALU Cream (250 ml. [.07 gal.]), flat and waffle polishing foams, microfibre wipes, wrench for pad change and apron. NEW! NEW! Part Number Model Motor Motor Sound Maximum Air Flow Hose Size Air Pressure Spindle Weight Length Height Number W (hp) RPM Level CFM/SCFM (LPM) mm (Inch) Bar (PSIG) Thread kg (lb.) mm (Inch) mm (Inch) (.4) 2, db(a) 4/28 (793) 10 (3/8) 6.2 (90) 3/8"-24 male 0.9 (2.0) 264 (10-3/8) 64 (2-1/2) Additional Specifications: Air Inlet Thread 1/4" NPT 18

24 Two-Step Polishing System A proven method for repairing minor surface defects that protrude through the clear coat Step One Use Model Right Angle Mini-Orbital Sander or Model Palm-Style Mini-Dynorbital Sander. Place the sanding disc slightly off-center of the defect with slight pressure on the pad. Throttle the tool on and sand in a random pattern for 2-5 seconds. Water must be used for sanding lubrication. Apply water directly to the disc. Keep the sanding pad flat while sanding. Remove from surface, then throttle the tool off. Let the tool and the abrasive do the work; keep the sanding area as small as possible. When finished, wipe the area clean with a nonscratching cloth. Model Model Step Two Use Model mm (3") Dynabuffer or Model mm (5") Dynabuffer. Apply a small drop of polishing compound. Use the buff to spread compound evenly over spot. NOTE: precondition by evenly spreading compound directly on pad. Place the buff on the sanding area. Apply approximately 4.5 kg (10 lbs.) of force to the work surface. Throttle the tool on and adjust force as required. Buff in a random pattern for 5-10 seconds. Keep buff flat or slightly tipped forward. Feather the area with lighter pressure for two seconds. Wipe the area clean with non-scratching cloth and inspect. If scratches are still visible, re-polish as needed. Model Model

25 Right Angle Mini-Orbital Sander Model ,000 RPM Utilizes a powerful 298 W (.4 hp) air motor for quick, efficient removal of dust nibs and defects. Tool is lightweight and easy to use. Designed for spot repair on gelcoat and clearcoat paint systems, plus finesse sanding of small areas. 2.5 mm (1/8") orbital action minimizes swirl-marks. Tool can be used for both dry and wet applications (water from an outside source). Includes 32 mm (1-1/4") dia. rubber sanding pad (54018). See page 45 for optional pad listing. Also includes Gear Oil and Push-Type Gun. Palm-Style Mini-Dynorbital Model ,000 RPM Combined orbital and random action provides ultra-smooth finishes. 32 mm (1-1/4") dia. discs confine sanding to smallest possible area and eliminates need to refinish entire body panels. Weighs only 0.8 kg (1-3/4 lbs.) for greater comfort and control. Includes Random Orbital Sanding Head; 32 mm (1-1/4") dia. medium density sanding pad (54018) with sample micro-finishing film abrasive discs. 19 mm (3/4") dia. pads and discs are available. See page 45 for optional pad choices. Dynabuffers Features a 14 mm diameter offset orbit; runs at 10,000 RPM free speed. Patented balancer compensates for vibration when running under load resulting in a smooth operating performance. (Patent 6,206,771). Rear exhaust muffler design reduces sound levels. Model mm (3") Diameter 7,000 RPM Under Load Throttle lever may be positioned for right or left hand operation. Optional Safety-Lock Lever available. Includes Hanger Bracket and Backup Pad, see page 36 for optional pad listing. Optional Side Handle available. Model mm (5") Diameter 5,000 RPM Under Load Strong, single-piece tool handle minimizes air leakage and reduces chance of breakage. Lightweight, thermal-insulated housing reduces cold air transmission to the operator; standard safety-lock lever. Includes Hanger Bracket and Hook-Face Backing Pad (page 36); order optional Foam Buff (page 34). Model Model Sander Model Step One Step One Step Two Model Optional Accessory 8-Channel Pad Reduces Heat Build-Up Part Number See page 33. Model Motor Motor Sound Air Flow Rate Hose Size Spindle Air Pressure Weight Length Height Number W (hp) RPM Level CFM/SCFM (LPM) mm (Inch) Thread Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) (.15) 7, db(a) 3/20 (566) 10 (3/8) 5/16"-24 Female 5.5 (80) 0.9 (2) 210 (8-1/4) 80 (3-1/8) (.4) 12, db(a) 3/20 (566) 6 (1/4) N/A 6.2 (90) 0.7 (1.5) 173 (6-7/8) 97 (3-7/8) (.5) 5, db(a) 1/6 (170) 6 (1/4) 1/4"-20 male 6.2 (90) 0.8 (1.8) 127 (5) 92 (3-5/8) (.36) 5, db(a) 3/20 (566) 10 (3/8) 5/16"-24 Female 6.2 (90) 1.2 (2.6) 260 (10-1/4) 114 (4-1/2) Additional Specifications: Air Inlet Thread 1/4" NPT 20

26 Cut-Off Wheel Tools 76 mm (3") Diameter Straight-Line Cut-Off Wheel Tool Model Cut sheet metal, frame rails, clamps, rusted bolts. Use on all kinds of metal cutting operations; also ideal for fiberglass. 20,000 RPM. Compact, lightweight design permits easy access to tight spots. Composite grip absorbs vibration and reduces cold air transmission to the operator. Safety-lock lever throttle. Rear exhaust, directs air away from work. Accepts 76 mm (3") dia. cut-off wheels with 10 mm (3/8") center hole. Model Offset Cut-Off Wheel Tool Model Offset design provides maximum user comfort and control. Composite grip absorbs vibration and reduces cold air transmission to the operator. Front exhaust keeps work surface clear. Accepts 76 mm (3") dia. cut-off wheels with 10 mm (3/8") center hole. Model IMPORTANT: Always use proper guards, wear eye gear and body protection. Never mount wheels which have lower RPM rating than the tool. Model Model Long Neck 76 mm (3") Diameter Cut-Off Wheel Tool Model Extension design is advantageous over conventional cut-off tools, allowing access to tight or confined areas. Tool design allows for easier straight-type cuts. Offers better visibility of workpiece. 20,000 RPM with rear exhaust. Accepts 76 mm (3") dia. cut-off wheels with 10 mm (3/8") center hole. Comfortable composite handle insulates from cold air. Plenty of power for everyday shop tasks. Adjustable guard. NEW! NEW! Optional Accessories Cut-Off Wheels Part Number mm (3") diameter. Part Number mm (4") diameter. Model Motor Motor Sound Air Flow Rate Air Inlet Hose Size Air Pressure Weight Length Height Number W (hp) RPM Level CFM/SCFM (LPM) Thread mm (Inch) Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) (.5) 20, db(a) 3/28 (793) 1/4" NPT 10 (3/8) 6.2 (90) 0.8 (1.8) 191 (7-1/2) 83 (3-1/4) (.5) 20, db(a) 3/28 (793) 1/4" NPT 10 (3/8) 6.2 (90) 0.9 (2.0) 305 (12) 89 (3-1/2) (.5) 20, db(a) 3/22 (623) 1/4" NPT 10 (3/8) 6.2 (90) 1.0 (2.2) 222 (8-3/4) 127 (5) 21

27 Die Grinders Composite grip absorbs vibration and reduces cold air transmission to the operator. Safety-lock lever throttle is standard on all models. Model Straight-Line Die Grinder Model /4" Collet 20,000 RPM. Powerful 373 W (.5 hp) motor provides excellent torque. Use with our carbide burr sets. Model Slow Speed Straight-Line Die Grinder Model /4" Collet 3,200 RPM. High torque and low speed make this tool ideal for tire buffing or pinstripe removal. Rear exhaust directs air away from work. Model Slow Speed Extension Die Grinder Model /4" Collet 3,200 RPM. An additional 102 mm (4") of reach, over conventional die grinders, for recessed and difficult-to-reach areas. Rear exhaust directs air away from work. Model Mini Straight-Line Die Grinder Model Model /4" Collet 6 mm Collet 25,000 RPM. Compact, lightweight, easy to use design. Smooth, efficient air motor with built-in speed regulator. Rear exhaust directs air away from work. Optional collet inserts: 1/8" (P/N 18432); 3 mm (P/N 18430). 7 Offset Die Grinder Model /4" Collet 20,000 RPM. 7 offset handle for comfort and control. Front exhaust. Model Model Motor Motor Sound Air Flow Rate Air Inlet Hose Size Air Pressure Weight Length Height Number W (hp) RPM Level CFM/SCFM (LPM) Thread mm (Inch) Bar (PSIG) kg mm mm 18000/ (.4) 25, db(a) 4/28 (793) 1/4" NPT 10 (3/8) 6.2 (90) 0.5 (1.1) 165 (6-1/2) 44 (1-3/4) (.5) 20, db(a) 3/22 (623) 1/4" NPT 10 (3/8) 6.2 (90) 0.9 (2.0) 203 (8) 146 (5-3/4) (.3) 3, db(a) 3/17 (481) 1/4" NPT 10 (3/8) 6.2 (90) 0.8 (1.8) 191 (7-1/2) 44 (1-3/4) (.3) 3, db(a) 3/17 (481) 1/4" NPT 10 (3/8) 6.2 (90) 1.0 (2.2) 260 (10-1/4) 44 (1-3/4) (.5) 20, db(a) 5/34 (963) 1/4" NPT 10 (3/8) 6.2 (90) 1.1 (2.4) 152 (5) 203 (8) 22

28 Die Grinders (Cont d) Mini Right Angle Die Grinder Model Model /4" Collet 6 mm Collet 20,000 RPM. Applications: high speed porting, blending, and deburring where clearance is a factor. Rear exhaust directs air away from work. Compact, lightweight design permits easy access to tight spots. Optional collet inserts: 1/8" (P/N 18432); 3 mm (P/N 18430). Model Die Grinder/Disc Sander Kit Kit 20,000 RPM. Two tools in one! Convenient for surface preparation, scuffing, deburring and light-duty general jobs. Kit comes complete with accessories for easy conversion between die grinder/disc sander. Includes: Model Die Grinder, 76 mm (3") hard density backup pad; trial pack of assorted 76 mm (3") dia. coated and non-woven nylon abrasives; /4"-20 shank; Dynaswivel ; deluxe storage/carry case. Model Model Motor Motor Sound Air Flow Rate Air Inlet Hose Size Air Pressure Weight Length Height Number W (hp) RPM Level CFM/SCFM (LPM) Thread mm (Inch) Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) 18010/ (.4) 20, db(a) 3/19 (538) 1/4" NPT 10 (3/8) 6.2 (90) 0.6 (1.3) 165 (6-1/2) 76 (3) Disc Sanders Model Model mm (2") Diameter 76 mm (3") Diameter Includes 51 mm (2") dia. Includes 76 mm (3") dia. locking-type pad. locking-type pad. 7 offset handle for comfort and control, front exhaust, safety-lock lever throttle. Composite grip absorbs vibration and reduces cold air transmission to the operator. Star Sander Kit Model Uses Spindle-Mount Stars Scuff composite bumpers, air damns, spoilers and many other uneven surfaces in automotive applications without damaging the profile. Great for preparing truck beds for spray-on coatings. Lightly deburr metal or fabrication. Variable-speed. Sanding stars are pre-mounted four per 1/4" shaft. Kit includes: Model Slow Speed Straight-Line Die Grinder; air-flow control Dynaswivel fitting (for maximum tool maneuverability and control) and an assortment of sanding stars. 23 FLEXIBLE SANDING STARS REACH IRREGULAR AREAS! Model Model Motor Motor Sound Air Flow Rate Air Inlet Hose Air Pressure Weight Length Height Number W RPM Level CFM/SCFM (LPM) Thread Size Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) , db(a) 3/22 (623) 1/4" NPT 10 mm 6.2 (90) 0,8 (1.8) 216 (8-1/2) 140 (5-1/2) , db(a) 3/22 (623) 1/4" NPT 10 mm 6.2 (90) 0,9 (2.0) 210 (8-2/4) 133 (5-1/4) Model Motor Motor Sound Air Flow Rate Air Inlet Hose Size Air Pressure Weight Length Height Number W (hp) RPM Level CFM/SCFM (LPM) Thread mm (Inch) Bar (PSIG) kg (lb.) mm (Inch) mm (Inch) (.3) 3, db(a) 5/34 (963) 1/4" NPT 10 (3/8) 6.2 (90) 1.1 (2.4) 203 (8) 44 (1-3/4) Additional Specifications: 3/8"-24 Female Spindle Thread

29 Portable Vacuum Systems Ready for connection to Dynabrade vacuum-ready tools, these systems efficiently remove dust and debris, while providing versatility and portability unique to Dynabrade. Dry vacuum only. Heavy duty stainless steel drum. Two-tool setup: two pneumatic outlets and two vacuum hose ports. HEPA filtration (0.3 micron) with felt insert and paper bag Classified in the dust class M in accordance with the European Standard EN Variable vacuum control. Electronic thermal protection device prevents heat overload of motor. Heavy duty four-wheel trolley with easy tilt n clean drum. Drum can be removed for special applications or locations. Disposable paper bag fits inside steel drum for convenient collection/disposal of debris. One disposable paper bag included with vacuum purchase. (Reorder part number for 36 L [9.9 gal.] vacuum; part number for 64 L [17 gal.] vacuum.) Max flow internal pneumatic workings. 2.3 m (7.5') water static lift/230 mbar vacuum. Two of the most innovative, lightweight 32 mm (1-1/4") dia. x 6 m (19.7') long coaxial hoses on the market today (see page 43). Auto on/off switch, 8 m (26-1/4') electrical cord. UL (United States and Canada), Gost and CE approved/listed. All models feature Dynabrade s Composite-Style Couplers for maximum air flow to tools and easy connect/disconnect by single push-button action. Also includes Vacuum Hose Swivel Adapter (see page 42). Lightweight vacuum hose connection swivels to add flexibility to your vacuum hose connection. HEPA filtration (0.3 micron) Unit shown without hoses Model Capacity Voltage / Plug Air Pressure Water Static Lift Sound Shipping Weight Height Width Number Litres (Gallon) Frequency Watts (Region) Bar (PSIG) cm/inch/mbar Level kg (lbs.) cm (Inch) cm (Inch) (9.9) 230V/50 Hz 1,400 UK (UK) 6.2 (90) 229/90/ db(a) 22 (48.4) 98 (38-1/2) 53 (20-7/8) (17) 230V/50 Hz 1,400 UK (UK) 6.2 (90) 229/90/ db(a) 28 (61.6) 114 (44-7/8) 70 (27-5/8) (9.9) 110V/60 Hz 1,300 UK (UK) 6.2 (90) 229/90/ db(a) 22 (48.4) 98 (38-1/2) 53 (20-7/8) (17) 110V/60 Hz 1,300 UK (UK) 6.2 (90) 229/90/ db(a) 28 (61.6) 114 (44-7/8) 70 (27-5/8) (9.9) 230V/50 Hz 1,400 CEE7/XVII (Europe) 6.2 (90) 229/90/ db(a) 22 (48.4) 98 (38-1/2) 53 (20-7/8) (17) 230V/50 Hz 1,400 CEE7/XVII (Europe) 6.2 (90) 229/90/ db(a) 28 (61.6) 114 (44-7/8) 70 (27-5/8) 24

30 ACCESSORIES Table of Contents Categorical Index - In Alphabetical Order Air Supply Accessories Air Lube and Grease Dynabrade Air Lube...29 Grease and Grease Gun...29 Air Supply Air Hose Assembly...29 Fittings...29 Flexible Air Line Assemblies...29 Speed Control Dial...29 Swivel Air Line Hoses...29 Couplers and Plugs...31 Coupler and Plug Assemblies...31 DynaJet In-Line Blow Gun...30 Dynaswivel Air Line Connectors...32 Filter-Regulator-Lubricator...30 Compounds ALU Cream...45 Dynabrade Glaze...45 Finesse Sanding Creme...45 Handles Bow-Type Handle...47 Interface Pads and Pad Conversions Dynafoam Interface Pads...44 Pad Conversions Hook-to-Vinyl Conversions...44 Vinyl-to-Hook Conversions...44 Polishing Pads Dynabuffer Polishing Pad...33 Hook-Face Polishing Pads...34 Repair and Tune-Up Accessories Drop-In Motor Repair Kit...47 Full Service Repair Kit mm Wrench...47 Replacement Drop-In Motors...47 Tune-Up Kit...47 Disc Pads Disc Sanding Pads and Assemblies Disc Pad Assembly...33 Locking-Type Discs...33 PSA-Type Discs...33 Mini-Dynorbital Disc Pads Foam Backing...33 Rigid Backing...33 Wet/Dry Sander Disc Pads...34 Accessories for Portable Vacuum Systems Dust Collection Receptacles and Systems Dust Collection Receptacles...28 Self-Contained Dust Collection Systems...28 Hose and Vacuum Accessories...28 Random Orbital Sander Brush Ring...47 Vacuum Accessories Coaxial Vacuum Hose Assemblies...27 Disposable Bags...26 Hose Cuffs...27 Locking-Front Wheel Assembly...26 Vacuum Cleaning Kit...26 Vacuum Hose Swivel Adapters...26 Vacuum Tray...26 Wall Mount Bracket...26 Y Vacuum Connector...26 Vacuum Conversion Kits...26 DynaZip Accessories Zip Wire Wheels...47 Zip Wire Wheel Hub Assemblies...47 Zip-Eraser Decal Removal Wheel...47 Sanding Heads and Sanding Pads File Board Sanding Pads (279 mm [11"])...42 Dynabug Sanding Pads Dynabug Model T Sanding Pads...40 Dynabug Sanding Pads...41 Dynabug II Sanding Pads...41 Wet Dynabug Model T Sanding Pads...40 Dynafine Sanding Pads Dynafine Sanding Pads...43 Wet Dynafine Sanding Pads...43 Dynaline Sanding Pads...42 Gear-Driven Sanding Pads Foam-Backed Sanding Pads...39 Hook-Face Pads...39 Rubber Pads...38 Vinyl-Face Pads...38 Mini-Dynorbital Sanding Heads...45 Mini-Dynorbital Sanding Pads...45 Random Orbital Sanding Pads HiVac 3-Hole Pad...37 Hook-Face Pads...36 Mesh Abrasive Pad...37 Multi-Use Sanding Pad...37 Radius Edge Pad...37 Rubber Pads...37 Vinyl-Face Pads...35 Threaded Adapters Collet-to-Thread Adapters...46 NPT Threaded Adapters...46 Threaded Adapters...46

31 Vacuum Conversion Kits For use with Dynorbital Spirit and Dynorbital Supreme Pad diameter determines which kit is right for your tool. Conversion kit allows user to change tool into desired vacuum configuration. Part Number Vacuum Accessories Vacuum Tray Part Number Part Number litres (9.9 gallon) 64 litres (17 gallon) A convenient, heavy duty storage tray for work-related items. Shown with optional Hanger, ideal for hanging vacuum hoses. Locking-Front Wheel Assembly Part Number Lock vacuum in place with the simple ease of a push-lock system. Pad Kit Part Diameter Converts Tool to Number 89 mm (3-1/2") Vacuum Ready mm (3-1/2") Central Vacuum mm (5") Vacuum Ready mm (5") Central Vacuum mm (6") Vacuum Ready mm (6") Central Vacuum Vacuum Cleaning Kit Part Number Includes 1.8 m (6') long x 32 mm (1-1/4") dia. vacuum hose, curved handle and two extension pipes along with round brush, crevice tool and coarse dirt nozzle attachments. For use with all electric portable vacuums Cleaning Kit is available - for use with discontinued vacuums (models and 64605). Y Vacuum Connector Part Number Allows two tools to be connected to the same portable vacuum system. Wall Mount Bracket Part Number Keep vacuum off floor and convenient for use. Disposable Bags Part Number Description For Use With Micron (400/case) Bag n Box System and Bag n Bag System Micron (24/pkg.) Bag n Box System and Bag n Bag System Micron (10/pkg.) Portable Vacuum Models 61300, 61302, 61304, and Micron (10/pkg.) Portable Vacuum Models 61301, 61303, 61305, and Plastic (12/pkg.) Portable Vacuum Model Vacuum Hose Swivel Adapters The adapter SWIVELS for comfortable tool maneuverability. Easy connection to air tools; 25 mm (1"). Part Number Part Number /8" Swivel Adapter 1-1/4" Swivel Adapter 25 mm (1") connection 32 mm (1-1/4") connection to vacuum hose. to vacuum hose. 26

32 Coaxial Vacuum Hose Assemblies For Dynabrade Vacuum System Part Number Standard 32 mm (1-1/4") dia. x 6 m (20') Long Coaxial Vacuum Hose Assembly Swivel Adapter P/N Cuff P/N /4" (32 mm) Vac Hose Cuff with Air Line Exit 1-1/4" (32 mm) Vac Hose Cuff with Air Line Exit 1-1/4" (32 mm) Vac Hose Cuff P/N For Older Two-Hand Tools Insert P/N Air Line Assembly mm (11") of Air Line Assembly will Extend Past the Cuff Dynabrade Coupler P/N Dynabrade Male Plug P/N mm (13-3/4") of Air Line Assembly will Extend Past the Cuff Dynabrade Female Plug P/N For Non-Dynabrade Vacuum Systems Part Number Optional 32 mm (1-1/4") dia. x 6 m (20') Long Coaxial Vacuum Hose Assembly Swivel Adapter P/N Cuff P/N /4" (32 mm) Vac Hose Cuff with Air Line Exit 1-1/4" (32 mm) Vac Hose Cuff with Air Line Exit 1-1/4" (32 mm) Vac Hose Swivel Adapter P/N Insert P/N Air Line Assembly mm (11") of Air Line Assembly will extend past the cuff Dynabrade Coupler P/N mm (25-5/8") of Air Line Assembly will Extend Past the Cuff Dynabrade Female Plug P/N Y-Adapter P/N MUST BE ORDERED SEPARATELY Hose Cuffs Many Configurations to Choose from Part Hose Tool Number Connection Connection /4" Thread 3/4" I.D. Non-Thread /4" Thread 3/4" I.D. Non-Thread " Thread 1" I.D. Non-Thread " Thread 1" I.D. Non-Thread " Thread 1-1/4" I.D. Non-Thread /4" Thread 1" I.D. Non-Thread /4" Thread 1-1/2" Thread /4" Thread 1-1/4" Thread /4" Thread 1-1/4" I.D. Non-Thread /2" Thread 1-1/4" I.D. Non-Thread /2" Thread 1" I.D. Non-Thread /2" I.D. Non-Thread 1-1/4" Thread /2" Thread 1" I.D. Non-Thread " Thread 1-1/4" I.D. Non-Thread " I.D. Non-Thread 1-1/2" Thread /4" I.D. Non-Thread 1-1/4" Thread NOTE: Part Number includes Cuff Adapter & mm (2") Swivel Cuff. Part Number is a swivel cuff

33 Dust Collection Receptacles Easily Attach to Air Powered Dynorbital Vacuum Models Mini-Reusable Felt Bag Part Number mm (11") long x 76 mm (3") wide. End opens up - no need to remove bag from tool when emptying. New bag design features a one micron filter rating. Bag traps over 99% of vacuum particles one micron or larger. Reusable Felt Bag Part Number Hook n Loop End 368 mm (14-1/2") long x 191 mm (7-1/2") wide. New bag design features a one-micron filter rating. Bag traps over 99% of vacuum particles one micron or larger. Reusable Felt Bag Part Number Zipper-Lock End 368 mm (14-1/2") long x 191 mm (7-1/2") wide. New bag design features a one micron filter rating. Bag traps over 99% of vacuum particles one-micron or larger. Self-Contained Dust Collection Systems Easily Attach to Air Powered Dynorbital Vacuum Models Mini-Flex-Hose System Part Number Air Line 6 mm (1/4") dia. x 711 mm (28") long Flex-Hose 25 mm (1") dia. x 457 mm (18") long Mini-Reusable Felt Bag. 1.8 m (6') Long Flex-Hose Systems Both systems include 25 mm (1") dia. x 1.8 m (6') long Flex-Hose. Part Number Includes Bag. Part Number Includes Bag. Bag-in-Box System Part Number Includes: Air Line, 1.5 m (5') long, Flex-Hose (25 mm [1"]dia. x 1.8 m [6'] long) and Durable Box Receptacle (to house bag and store tool). Sample paper bag included. Paper bag reorder: (400/case) or (24/pkg.) Shown with optional airline Hose and Vacuum Accessories Exhaust Hose Assembly Part Number mm (1") Diameter x 3 m (10') Long Flex Hose: 25 mm (1") dia. x 3 m (10') long with cuffs Air Line: 6 mm (1/4") dia. x 3 m (10') long Rubber Connectors. Use with Dynorbital Sanders. Hose Cover Part Number m (5') Long Cloth Cover Covers air line and exhaust/vacuum hoses (not included). Eliminates damage from hoses dragging on the workpiece. Rubber Connectors Part Number (5/pkg.) Used to strap tool air line to tool s exhaust hose for easy all-in-one maneuverability. Overskirt Shrouds For Dynorbital Supreme and Dynorbital Spirit Sanders Has built-in vacuum port. Maximize dust pick-up on vacuum models. Replace standard lip-seal shrouds in seconds. Protects pad edges when working near workpiece sides. Part Number mm (3-1/2") Diameter For use with 76 mm (3") and 89 mm (3-1/2") Random Orbital Sanders only. Part Number mm (5") Diameter For use with 127 mm (5") Random Orbital Sanders only. Part Number mm (6")Diameter For use with 152 mm (6") Random Orbital Sanders only. 28

34 Air Supply Accessories Swivel Air Line Hoses Eliminates kinking, fittings swivel 360 for easy use. Tough, flexible and lightweight. Part Hose O.D. Hose I.D. Length Number mm (Inch) mm (Inch) (Feet) Description (1/4) 4 (5/32) 910 mm (3) 1/4" female to 1/4" male (1/4) 4 (5/32) 910 mm (3) 1/4" female to 1/8" male (1/4) 4 (5/32) 1.8 m (6) 1/4" female to 1/4" male (1/4) 4 (5/32) 1.8 m (6) 1/4" female to 1/8" male (1/4) 4 (5/32) Custom Hose by the foot (no fittings) Order fittings separately, if desired (3/8) 6 (1/4) 910 mm (3) 1/4" female to 1/4" male (3/8) 6 (1/4) 1.8 m (6) 1/4" female to 1/4" male (3/8) 6 (1/4) Custom Hose by the foot (no fittings) Order fittings separately, if desired Speed Control Dial Mounts directly to air tool. Part Number Part Number /4" NPT connection 3/8" NPT connection Up to 708 LPM (25 SCFM). Up to 736-1,274 LPM (26-45 SCFM). Fittings Part For Use Number With Description mm (1/4") Hose 1/4" NPT female mm (1/4") Hose 1/4" NPT male mm (1/4") Hose 1/8" NPT male mm (3/8") Hose 1/4" NPT female mm (3/8 Hose 1/4" NPT male Air Lube and Grease Dynabrade Air Lube (10W/NR) Formulated for pneumatic equipment. Absorbs up to 10% of its weight in water. Prevents rust and formation of gum/sludge for longer tool operation with greater power and less downtime. Part Number Part Number ml (4 oz.) 473 ml (1 pt.) Air Hose Assembly Part Number Part Number mm Dia. x 7.6 m (25') Long Air Hose by the Metre 48 SCFM (1,359 LPM) Use this assembly to connect an FRL to a Dynabrade tool for optimum results. Air line is 66% lighter than conventional PVC and rubber hoses. Reinforced hose is made of an anti-abrasive PU and thermoplastic rubber compound. High flexibility and narrow bending radius of hose prevent choking. High resistance to ozone, hydrocarbons, fats, oils, and slightly aggressive chemical products. Flexible Air Line Assemblies Part Hose I.D. Female Male Number mm (Inch) Fittings Fittings Length (1/4) m (5 ft.) (1/4) mm (28") (1/4) 0 0 Custom (1/4) 1 1 Custom (3/8) m (8 ft.) (1/2) m (5 ft.) NOTE: 95807: Specify length 95938: Specify length; includes one set factory-installed male and female fittings Grease and Grease Gun Multi-purpose grease for all types of bearings, cams, gears. High film strength; excellent resistance to water, steam, etc. Workable range -18 C to 149 C (0 F to 300 F). Part Number Part Number l (1 gallon) Display Box ml (4 oz.) bottles Part Number Part Number Push-Type Grease Gun g (10 oz.) tube One-hand operation. 29

35 Filter-Regulator-Lubricator Filter Two stage filtration of water and contaminants from the air system. Part Number Air Inlet Thread /8" NPT /2" NPT Regulator Features safety-lock knob for maintaining accurate air pressure regulation. Part Number Air Inlet Thread /8" NPT /2" NPT Lubricator Adjustable oil drop to meter the amount of oil into the air system. Part Number Air Inlet Thread /8" NPT /2" NPT Additional Specifications: Maximum Air Flow 9.7 Bar (140 PSIG) Female Ports 3/8" NPT = 1,133 LPM ( Bar (100 PSIG) 1/2" NPT = Up to 1,558 LPM ( Bar (100 PSIG) NOTE: For installation and maintenance instructions refer to Dynabrade s Filter-Regulator-Lubricator Manual (PD00.72) Filter-Regulator Two stage filtration of water and contaminants from the air system. Features safety-lock knob for maintaining accurate air pressure regulation. Part Number Air Inlet Thread /8" NPT /2" NPT Regulator-Lubricator Features safety-lock knob for maintaining accurate air pressure regulation. Adjustable oil drop to meter the amount of oil into the air system. Part Number Air Inlet Thread /8" NPT /2" NPT Filter-Regulator-Lubricator Two stage filtration of water and contaminants from the air system. Features safety-lock knob for maintaining accurate air pressure regulation. Adjustable oil drop to meter the amount of oil into the air system. Part Number Air Inlet Thread /8" NPT /2" NPT DynaJet In-Line Blow Gun Clean Off Work Surfaces Without Disconnecting Only connect once... permanently mounts between coupler & air hose. Purges air line of water & contaminants before starting up air tools. Durable aluminum construction, weighs only 0.06 kg (2 oz.). Each unit has 1/4" female NPT thread at both ends for easy installation. Part Number Standard Design Provides no restriction of air line pressure. Part Number Safety Tip Design Reduces line pressure down to 2 Bar (30 PSIG). Meets O.S.H.A. requirements of special relief hole in nozzle which limits pressure to 2 Bar (30 PSIG) when dead ended and used on an air line of 10.3 Bar (150 PSIG) or less. Part Number Part Number Proper Installation for DynaJet In-Line Blow Gun Connection Coupler Blow Gun Air Line Part Thread Weight Recommended Air Flow Number Size kg (lb.) Range SCFM (LPM) /4" Female NPT 0.06 kg up to 35 SCFM (991 LPM /4" Female NPT 0.06 kg up to 991 LPM 10.3 Bar (150 PSIG) maximum on all models 1/4" Male NPT 1/4" Male NPT 1/4" Female NPT on both ends 30

36 Couplers and Plugs Steel and Brass Couplers Durable nickel-plated steel and brass construction. Single action quick-connect by just inserting plug into coupler. Pull back on sleeve of coupler for quick disconnect. Part Body Thread Size Air Flow Range Number Size NPT SCFM (LPM) /4" 1/4" Female Up to 74 (2,095) /4" 1/4" Male Up to 74 (2,095) /8" 3/8" Female Up to 138 (3,900) /8" 3/8" Male Up to 138 (3,900) /2" 1/2" Female Up to 138 (3,900) /2" 1/2" Male Up to 138 (3,900) Composite-Style Couplers Composite-style design provides maximum air flow to tools. Heavy duty construction. Easy connect/disconnect by single push-button action. Shock-proof, low-vibration, crush-resistant. Lightweight 0.04 kg (1.4 oz.), non-marring composite material. Part Body Thread Size Air Flow Range Number Size NPT SCFM (LPM) /4" 1/4" Female Up to 83 (2,350) /4" 1/4" Male Up to 83 (2,350) Plugs Coupler Thread Size Coupler Body Size Durable zinc-plated steel construction. Plugs all have ported design to prevent starving of the air tool. Provides up to twice the air flow compared to standard plug design. Part Body Thread Size Air Flow Range Number Size NPT SCFM (LPM) /4" 1/4" Male Up to 74 (2,095) /4" 1/4" Female Up to 74 (2,095) /4" 3/8" Male Up to 74 (2,095) /8" 3/8" Male Up to 138 (3,900) /8" 3/8" Female Up to 138 (3,900) /2" 1/2" Male Up to 138 (3,900) /2" 1/2" Female Up to 138 (3,900) Coupler and Plug Assemblies Assemblies include one coupler and one plug. Maximum working pressure: 10 Bar (150 PSIG). Temperature Range: -20 C to 100 C (-4 F to 212 F). Plugs with Composite-Style Couplers Heavy duty construction. Composite-style design provides maximum air flow to tools. Easy connect/disconnect by single push-button action. Plugs provide up to twice the air flow compared to standard plug design. Coupler Coupler Plug Plug Air Flow Part Body Thread Body Thread Range Number Size Size (NPT) Size Size (NPT) SCFM (LPM) /4" 1/4" Female 1/4" 1/4" Male Up to 83 (2,350) /4" 1/4" Female 1/4" 1/4" Female Up to 83 (2,350) /4" 1/4" Male 1/4" 1/4" Male Up to 83 (2,350) /4" 1/4" Male 1/4" 1/4" Female Up to 83 (2,350) 31 Plugs with Steel and Brass Couplers Durable steel construction. Single action quick-connect by just inserting plug into coupler. Pull back on sleeve of coupler for quick disconnect. Plugs provide up to twice the air flow compared to standard plug design. Coupler Coupler Plug Plug Air Flow Part Body Thread Body Thread Range Number Size Size (NPT) Size Size (NPT) SCFM (LPM) /4" 1/4" Female 1/4" 1/4" Male Up to 74 (2,095) /4" 1/4" Female 1/4" 1/4" Female Up to 74 (2,095) /4" 1/4" Male 1/4" 1/4" Male Up to 74 (2,095) /4" 1/4" Male 1/4" 1/4" Female Up to 74 (2,095) /8" 3/8" Female 3/8" 3/8" Male Up to 138 (3,900) /8" 3/8" Female 3/8" 3/8" Female Up to 138 (3,900) /8" 3/8" Male 3/8" 3/8" Male Up to 138 (3,900) /8" 3/8" Male 3/8" 3/8" Female Up to 138 (3,900) /2" 1/2" Female 1/2" 1/2" Male Up to 138 (3,900) /2" 1/2" Female 1/2" 1/2" Female Up to 138 (3,900) /2" 1/2" Male 1/2" 1/2" Male Up to 138 (3,900) /2" 1/2" Male 1/2" 1/2" Female Up to 138 (3,900)

37 Dynaswivel THE PROBLEM Air Line Connectors Aluminum and Stainless Steel Construction Single Pivot Right angle single-pivot swivels 360 at one location. Designed to permit air hose to extend horizontally away from tool while allowing 360 tool maneuverability. Great for stationary equipment. THE SOLUTION Part Thread Flow Air Flow Range Weight Number Size Control SCFM (LPM) kg (lb.) 95590** 1/4" NPT No up to 25 (708) 0.05 (0.11) 95591** 3/8" NPT No ( ) 0.12 (0.26) 95592** 1/2" NPT No ( ) 0.21 (0.46) Double Pivot Swivels 360 AT TWO PIVOT POINTS allowing the air hose to drop directly to the floor while providing superb tool handling. Never Fight an Air Hose Again! The Dynaswivel is a universal-joint that connects portable air tools to an air line. It improves tool maneuverability, minimizes operator fatigue and extends hose life. Patented; works great on air tools or paint guns. Non-Marring Composite Construction Double Pivot Swivels 360 AT TWO PIVOT POINTS allowing the air hose to drop directly to the floor while providing superb tool handling. Double Pivot, Flow Control Swivels 360 AT TWO PIVOT POINTS allowing the air hose to drop directly to the floor while providing superb tool handling. Finger-tip air-flow control dial. Double Pivot, Flow Control Swivels 360 AT TWO PIVOT POINTS allowing the air hose to drop directly to the floor while providing superb tool handling. Finger-tip air-flow control dial. Part Thread Flow Air Flow Range Weight Number Size Control SCFM (LPM) kg (lb.) 95852** 1/8" Male x 25 No up to 25 (708) 0.08 (0.18) 1/4" NPT Female 95460** 1/4" NPT No up to 25 (708) 0.09 (0.20) 95734** 1/4" NPT Yes up to 25 (708) 0.11 (0.24) 95461** 3/8" NPT No ( ) 0.18 (0.40) 95462** 1/2" NPT No ( ) 0.36 (0.80) 95690** 3/4" NPT No above 65 (1840) 0.68 (1.50) Dynaswivel Display Pak Model Includes one counter top display box and ten Dynaswivel Air Line Fittings. Part Thread Flow Air Flow Range Weight Number Size Pivot Control SCFM (LPM) kg 94300* 1/4" NPT Double No up to 33 (935) 0, * 1/4" NPT Double Yes up to 46 (1303) 0,08 IMPORTANT: 10.3 Bar (150 PSIG) maximum on all models *NOTE: Do not exceed recommended torque value of newton metres **NOTE: Do not use on percussion tools or in areas of high mechanical abuse 32

38 Disc Sanding Pads and Assemblies For Locking-Type Discs 51 mm (2"), 76 mm (3") and 102 mm (4") Dia. Pads A quick turn of the disc locks it into place. 51 mm (2") and 76 mm (3") dia. pads include Pad Adapter to convert 1/4"-20 female thread to 1/4" dia. shank for use with collets and chucks. Mini-Dynorbital Disc Pads 76 mm (3") Diameter Compatible with angle-head and palm-style Mini-Dynorbital sanders; Angle-Head Polishers. Hook-face pads accept reattachable abrasive discs as well as polishing buff pads. 5,000 RPM maximum. Foam Backing Part Thread Number Size /4"-20 Female /8"-24 Female Part Diameter Pad MOS Number mm (Inch) RPM Thread Density 51344* 51 (2) 30,000 1/4"-20 Female Medium (2) 30,000 3/8"-24 Female Medium 51346* 76 (3) 20,000 1/4"-20 Female Medium (3) 20,000 3/8"-24 Female Medium (4) 12,000 3/8"-24 Female Hard * Includes Pad Adapter to convert 1/4"-20 female thread to 1/4" dia. shank for use with collets and chucks Use tool RPM and abrasive manufacturer s maximum operating speed as your guidelines for compatibility For PSA-Type Discs 51 mm (2") Dia. Pads Easy application and removal of disc. Remove the disc s liner to reveal a pressure-sensitive adhesive coating. Peel the old disc off the pad and press on the new disc! Rigid Backing Part Thread Number Size /4"-20 Female /8"-24 Female Dynabuffer Polishing Pad Hard Density Foam Eight-channel design reduces heat build-up Non-vacuum pad with eight holes. Each hole has a channel that extends to pad edge for cooling effect. Part Diameter Pad MOS Number mm (Inch) RPM Thread Density (2) 20,000 1/4"-20 Female Medium (2) 20,000 3/8"-24 Female Medium Use tool RPM and abrasive manufacturer s maximum operating speed as your guidelines for compatibility Disc Pad Assembly 51 mm (2") Dia. Pad Includes PSA Disc Pad and Pad Adapter (converts 1/4"-20 female thread to 1/4" dia. shank for use with collets and chucks). 33 Hook-Face 127 mm Diameter Part MOS Number (RPM) Nap Holes Channels Thickness Thread ,000 Short mm (3/4") 5/16"-24

39 Hook-Face Polishing Pads For Use With DynaBuffers and Polishers Yellow Foam Cutting - foam cells are larger and further apart than White Foam cells making the action more aggressive. White Foam Polishing - foam cells are smaller and closer together than Yellow Foam cells making the action less aggressive. Orange Waffle Foam Use during compounding stage to remove swirl and haze marks. Non-Vacuum Pad Diameter Part Number Description Type Color Terry Cloth Polishing White Synthetic Wool Polishing White 76 mm (3") Foam Flat Polishing White Foam Flat Cutting Yellow Natural Sheepskin Polishing White 83 mm (3-1/4") Foam Waffle Polishing Orange 89 mm (3-1/2") Natural Sheepskin Polishing Tan 95 mm (3-3/4") Foam Waffle Polishing Orange Natural Sheepskin Polishing Tan 127 mm (5") Foam Flat Polishing White Foam Flat Cutting Yellow Natural Sheepskin Polishing White 133 mm (5-1/4") Foam Waffle Polishing Orange 54330* Foam Flat Polishing Yellow 152 mm (6") Foam Flat Cutting Yellow Foam Flat Polishing White 178 mm (7") Natural Sheepskin Polishing White *NOTE: Part Number has 5/16"-24 male thread Terry Cloth Application and removal of waxes and polishes. Synthetic Wool Final finishing and polishing. Natural Sheepskin Final finishing and polishing; softer feel than synthetic wool. Wet/Dry Sander Disc Pads Short Nap Hook-Face Pads For Use With 127 mm mm Dia. Wet/Dry Sanders Non-Vacuum Urethane Pads are long tapered with an extremely flexible edge for sanding contours. Rigid Backing For finishing flat surfaces with non-woven nylon abrasive discs. Foam Backing Soft, dual density bonded dual action pad for use on curved and contour surfaces. Pad Diameter Part Number Type MOS RPM Thread Rigid 6,000 1/4"-20 Female 127 mm (5") Rigid 6,000 3/8"-24 Female Rigid 10,000 M14 x Urethane 4,800 5/8"-11 Female 152 mm (6") Foam 3,200 5/8"-11 Female Urethane 4,800 5/8"-11 Female Foam 3,200 5/8"-11 Female 184 (7-1/4") Foam 3,200 M14 x mm (8") Foam 3,200 5/8"-11 Female 34

40 Vinyl-Face Random Orbital Sanding Pads Premium Urethane Sanding Pads Perfectly Weight-Mated for Dynabrade Tools 76 mm (3"), 89 mm (3-1/2"), 127 mm (5"), 152 mm (6") Pads:13,000 RPM maximum operating speed 5/16"-24 male thread 203 mm (8") Pads: 10,000 maximum operating speed Mounts with 5 screws Vinyl-Face Pads Ideal for PSA-type disc adhesion. Remove abrasive adhesive paper liner and press abrasive to vinyl-face sanding pad. Quick disc removal. Non-Vacuum Pads 35 Pad Diameter Part Number Thickness Density mm (5/8") Medium 76 mm (3")* mm (5/8") Soft 89 mm (3-1/2")* 127 mm (5") 152 mm (6") Non-Vacuum Pads High quality back-up pad. Weight-mated for smooth running and minimal tool vibration. Our exclusive single-piece hub design reduces face run out to only Competitors three-piece hubs can result in face run out from mm (5/8") Soft mm (5/8") Medium mm (3/8") Soft mm (3/8") Medium mm (5/8") Medium mm (5/8") Soft mm (3/8") Soft mm (3/8") Medium mm (5/8") Medium mm (5/8") Soft 203 mm (8") mm (3/8") Medium *NOTE: Our 76 mm (3") and 89 mm (3-1/2") pads, without holes, can also be used for vacuum sanding. Vacuum pick-up is around periphery of pad. Vacuum Pads Vacuum holes are precisely located to achieve proper alignment with abrasive discs for optimum vacuum capabilities. Vacuum Pads Pad Diameter Part Number Holes Thickness Density mm (5/8") Medium 76 mm (3")* mm (5/8") Soft 89 mm (3-1/2")* mm (5/8") Soft mm (5/8") Medium mm (3/8") Soft mm (3/8") Medium 127 mm (5") mm (5/8") Medium mm (5/8") Soft mm (3/8") Medium mm (3/8") Soft 152 mm (6") mm (3/8") Medium mm (5/8") Medium mm (5/8") Soft *NOTE: Our 76 mm (3") and 89 mm (3-1/2") pads, without holes, can also be used for vacuum sanding. Vacuum pick-up is around periphery of pad. Channel Vacuum Pads Channel Vacuum Pads 3 mm (1/8") deep recessed channel. No need to align vacuum holes to pad holes. Pad Diameter Part Number Holes Thickness Density mm (3/8") Soft 127 mm (5") mm (3/8") Medium mm (5/8") Medium mm (5/8") Soft mm (3/8") Soft 152 mm (6") mm (3/8") Medium mm (5/8") Medium mm (5/8") Soft

41 Hook-Face Random Orbital Sanding Pads Premium Urethane Sanding Pads Perfectly Weight-Mated for Dynabrade Tools 76 mm (3"), 89 mm (3-1/2"), 127 mm (5"), 152 mm (6") Pads:13,000 RPM maximum operating speed 5/16"-24 male thread 203 mm (8") Pads: 10,000 maximum operating speed Mounts with 5 screws Short nap Long nap Hook-Face Pads Short nap pads for use with reattachable discs. Long nap pads for use with non-woven nylon discs. Non-Vacuum Pads High quality back-up pad. Weight-mated for smooth running and minimal tool vibration. Vacuum Pads Vacuum holes are precisely located to achieve proper alignment with abrasive discs for optimum vacuum capabilities. Channel Vacuum Pads 3 mm (1/8") deep recessed channel. No need to align vacuum holes to pad holes. Non-Vacuum Pads Pad Diameter Part Number Thickness Nap Density mm (5/8") Short Medium 76 mm (3")* mm (5/8") Long Medium mm (1/2") Short Medium mm (5/8") Short Soft 89 mm (3-1/2")* mm (5/8") Short Hard mm (5/8") Long Medium mm (3/8") Short Medium 127 mm (5") mm (3/8") Short Soft mm (5/8") Short Medium mm (5/8") Short Soft mm (3/8") Short Medium 152 mm (6") mm (3/8") Short Soft mm (5/8") Short Medium mm (5/8") Short Soft 203 mm (8") mm (3/8") Short Medium *NOTE: Our 76 mm (3") and 89 mm (3-1/2") pads, without holes, can also be used for vacuum sanding. Vacuum pick-up is around periphery of pad. Vacuum Pads Pad Diameter Part Number Holes Thickness Nap Density mm (5/8") Short Medium 76 mm (3")* mm (5/8") Long Medium mm (1/2") Short Medium mm (5/8") Short Soft 89 mm (3-1/2")* mm (5/8") Short Hard mm (5/8") Long Medium mm (3/8") Short Medium mm (3/8") Short Soft 127 mm (5") mm (5/8") Short Medium mm (5/8") Short Soft mm (3/8") Short Medium mm (3/8") Short Medium mm (3/8") Short Medium mm (3/8") Short Soft 152 mm (6") mm (5/8") Short Medium mm (5/8") Short Soft mm (5/8") Short Medium mm (3/8") Short Medium *NOTE: Our 76 mm (3") and 89 mm (3-1/2") pads, without holes, can also be used for vacuum sanding. Vacuum pick-up is around periphery of pad. NOTE: Pad is urethane foam, see page 35 for complete pad description. Channel Vacuum Pads Pad Diameter Part Number Holes Thickness Nap Density mm (3/8") Short Medium 127 mm (5") mm (3/8") Short Soft mm (5/8") Short Medium mm (5/8") Short Soft mm (3/8") Short Medium 152 mm (6") mm (3/8") Short Soft mm (5/8") Short Medium mm (5/8") Short Soft 36

42 Rubber Random Orbital Sanding Pads Rubber Sanding Pads for the Economy-Minded Professional 12,000 RPM maximum operating speed 5/16"-24 male thread Medium density Non-Vacuum Pads Pad Diameter Part Number Face Nap Thickness Diamond 13 mm (1/2") 127 mm (5") Hook Long 13 mm (1/2") 152 mm (6") Diamond 13 mm (1/2") Hook Long 13 mm (1/2") Diamond Pattern Low-cost alternative to premium urethane pads for the economy-minded professional. Use with PSA-type abrasives. Radius Edge Pad Rounded Foam Edge 13,000 max. operating speed Soft density For use with with random orbital sanders. 5/16"-24 female thread. Rounded foam edge of soft density pad conforms to shape of coves and corners. Hook-face attachment is offset from pad edge, allowing abrasive to flex around radius. Ideal for use with scalloped edge abrasives. Non-Vacuum Pads Pad Part Radius Diameter Number Edge Nap Thickness 89 mm (3-1/2") mm (3/8") Short 16 mm (5/8") 127 mm (5") Vacuum Pads Post Pattern Grooves in bottom of pad allow for enhanced vacuum pick-up. No need to align vacuum holes with abrasive holes. Use with PSA-type abrasives mm (3/8") Medium 16 mm (5/8") mm (3/8") Short 16 mm (5/8") Pad Part Radius Diameter Number Edge Nap Holes Thickness 127 mm (5") mm (3/8") Short 5 16 mm (5/8") Medium density pad accepts 76 mm (3") dia. hook-face or mesh-style abrasive discs. 5/16"-24 female thread. Long Nap Hook-Face Use with non-woven nylon discs. HiVac 3-Hole Pad For use with HiVac Dynorbital-Spirit Random Orbital Sanders Vacuum Pad Pad Diameter Part Number Face Nap Holes Thickness 76 mm (3") Hook Short 3 13 mm (1/2") Vacuum Pads Pad Diameter Part Number Face Nap Holes Thickness Diamond 5 13 mm (1/2") 127 mm (5") Post Pattern 5 13 mm (1/2") Hook Long 5 13 mm (1/2") Diamond 6 13 mm (1/2") 152 mm (6") Post Pattern 6 13 mm (1/2") Hook Long 6 13 mm (1/2") Mesh Abrasive Pad Compatible with Mesh Abrasive Material 13,000 max. operating speed Medium density Medium density pad for use with random orbital sanders. Improved dust-free sanding of body fillers and primer. Eliminates pilling problems. 5/16"-24 female thread. Vacuum Pads Pad Diameter Part Number Face Nap Holes Thickness 127 mm (5") Hook Short mm (3/8") 152 mm (6") Hook Short mm (3/8") 279 mm (11") Hook Short mm (3/8") Multi-Use Sanding Pad Urethane Foam Use with 6, 7, 8, or 9-hole abrasive discs For use on random orbital sanders with vacuum capabilities on wood, metal and solid surfaces. Single-hub design reduces vibration and wear. 13,000 maximum operating speed; 5/16"-24 female thread. Vacuum Pad Pad Diameter Part Number Face Nap Holes Thickness 152 mm (6") Hook Short mm (5/8") 37

43 Vinyl-Face Gear-Driven Sanding Pads Premium Urethane Medium Density Perfectly Weight-Mated for Dynabrade Tools 4 screw-mount system on model numbers screw-mount system on model numbers screw-mount system on original aluminum housing tool design Vinyl-Face Pads Ideal for PSA-type disc adhesion. Remove abrasive adhesive paper liner and press abrasive to vinyl-face sanding pad. Quick disc removal. Non-Vacuum Pads High quality back-up pad. Weight-mated for smooth running and minimal tool vibration. Vacuum Pads Vacuum holes are precisely located to achieve proper alignment with abrasive discs for optimum vacuum capabilities. Channel Vacuum Pads 3 mm (1/8") deep recessed channel. No need to align vacuum holes to pad holes. Non-Vacuum Pads Pad Part Max. Diameter Number RPM Thickness Screws , mm (3/8") mm (5") , mm (3/8") , mm (3/8") , mm (3/8") mm (6") , mm (3/8") , mm (3/8") mm (8") , mm (1/2") 5 Vacuum Pads Pad Part MOS Diameter Number RPM Thickness Holes Screws 152 mm (6") , mm (3/8") , mm (3/8") mm (8") , mm (1/2") 8 5 Channel Vacuum Pad Pad Part Max. Diameter Number RPM Thickness Holes Screws 152 mm (6") , mm (3/8") 6 4 Rubber Gear-Driven Sanding Pads Rubber pads for the economy-minded professional. Long nap hook-face pads mount with five screws. Medium density. Rubber Pads Part MOS Vacuum Pad Dimensions Number (RPM) Type Holes Thickness 203 mm (8") ,500 Non-Vacuum 0 13 mm (1/2") ,500 Vacuum 8 13 mm (1/2") 38

44 Hook -Face Gear-Driven Sanding Pads Premium Urethane Medium Density Perfectly Weight-Mated for Dynabrade Tools 4 screw-mount system on model numbers screw-mount system on model numbers screw-mount system on original aluminum housing tool design Hook-Face Pads Short nap pads for use with reattachable discs. Non-Vacuum Pads High quality back-up pad. Weight-mated for smooth running and minimal tool vibration. Vacuum Pads Vacuum holes are precisely located to achieve proper alignment with abrasive discs for optimum vacuum capabilities. Channel Vacuum Pads 3 mm (1/8") deep recessed channel. No need to align vacuum holes to pad holes. Non-Vacuum Pads Pad Diameter Part Number Max. RPM Thickness Screws , mm (3/8") mm (5") , mm (3/8") , mm (3/8") , mm (3/8") mm (6") , mm (3/8") , mm (3/8") mm (8") , mm (1/2") 5 Vacuum Pads Pad Diameter Part Number Max. RPM Thickness Holes Screws , mm (3/8") mm (6") , mm (3/8") , mm (3/8") mm (8") , mm (1/2") 8 5 Channel Vacuum Pads Pad Part Max. Diameter Number RPM Thickness Holes Screws 152 mm (6") , mm (3/8") , mm (3/8") 8 5 Foam-Backed Sanding Pads Soft Density Sanding Pads Foam Backing Soft, dual density bonded dual action pad for use on curved and contour surfaces. Hook-Face Pads Short nap pads for use with reattachable discs. Rubber-Face For use with PSA and screen abrasives. Non-Vacuum Pads Pad Part MOS Mounts Diameter Number (RPM) Face with Thickness 152 mm (6") ,200 Rubber 5/8"-11 Female Thread 32 mm (1-1/4") 203 mm (8") ,200 Rubber 5/8"-11 Female Thread 32 mm (1-1/4") ,500 Hook 5 Screws 25 mm (1") NOTE: Part Number is weight-mated to Model (8" Gear-Driven Orbital Sander) 39

45 Dynabug Model T Sanding Pads Balanced and Weight-Mated to Dynabrade Tools All pads: 20,000 RPM max. operating speed All pads mount with four screws (except P/N mounts with clips) Vinyl-Face Sanding Pads Vinyl-Face Pads Ideal for PSA-type disc adhesion. Remove abrasive adhesive paper liner and press abrasive to vinyl-face sanding pad. Quick disc removal. Hook-Face Sanding Pads Hook-Face Pads Short nap pads for use with reattachable discs. Non-Vacuum Pads Pad Dimensions Part Number Thickness Density mm (5/8") Soft 127 mm (5") Dia mm (3/8") Medium 152 mm (6") Dia mm (3/8") Medium mm (5/8") Soft 102 mm (4") W x 110 mm (4-5/16") L mm (1/4") Medium with Clips 108 mm (4-1/4") W x mm (3/8") Medium 114 mm (4-1/2") L mm (5/8") Soft Vacuum Pads Pad Dimensions Part Number Holes Thickness Density mm (1/4") Medium 108 mm (4-1/4") W x mm (3/8") Medium 114 mm (4-1/2") L mm (5/8") Soft Non-Vacuum Pads Pad Dimensions Part Number Thickness Density mm (5/8") Soft 127 mm (5") Dia mm (3/8") Medium 152 mm (6") Dia mm (3/8") Medium mm (5/8") Soft 108 mm (4-1/4") W x mm (5/8") Soft 114 mm (4-1/2") L mm (3/8") Medium Vacuum Pads Pad Dimensions Part Number Holes Thickness Density 127 mm (5") Dia mm (1/2") Medium 152 mm (6") Dia mm (1/2") Medium 108 mm (4-1/4") W x 114 mm (4-1/2") L mm (3/8") Medium mm (5/8") Soft mm (3/16") Medium Wet Dynabug Model T Sanding Pads Hook-Face Balanced and Weight-Mated Sanding Pads All pads: 20,000 RPM max. operating speed All pads mount with four screws Hook-Face Pads Short nap pads for use with reattachable discs. Pads feature channels from vacuum holes to feed water through the sanding pad. Vacuum Pads Pad Dimensions Part Number Holes Thickness Density 127 mm (5") Dia mm (1/2") Medium 152 mm (6") Dia mm (1/2") Medium 40

46 Dynabug II Sanding Pads 10 mm (3/8") Thick, Medium Density Pads Pads mount with four screws NEW! Vinyl-Face Pads Ideal for PSA-type disc adhesion. Remove abrasive adhesive paper liner and press abrasive to vinyl-face sanding pad. Quick disc removal. Non-Vacuum Pads Hook-Face Pads Short nap pads for use with reattachable discs. Pad Dimensions Part Number Face 74 mm (3") x Hook 109 mm (4-1/4") Vinyl 80 mm (3-1/4") x Hook 130 mm (5") Vinyl 8 Holes 8 (4+4) Holes Delta-Style Loop-Face Pads Pads accept 3M Hookit II abrasives. Dynabug Sanding Pads 10 mm (3/8") Thick, Medium Density Pads Pads mounted with four screws Vacuum Pads Non-Vacuum Pads High quality back-up pad. Weight-mated for smooth running and minimal tool vibration. Vacuum Pads Vacuum holes are precisely located to achieve proper alignment with abrasive discs for optimum vacuum capabilities. Pad Dimensions Part Number Vacuum Holes Face 68 mm (2-3/4") x 196 mm (7-3/4") Loop 74 mm (3") x Hook 109 mm (4-1/4") Vinyl (4+4) Hook 80 mm (3-1/4") x Hook 130 mm (5") Vinyl mm (3-7/8") x Delta-Style Hook 143 mm (5-5/8") Delta-Style Loop NEW! NEW! Vinyl-Face Pads Ideal for PSA-type disc adhesion. Remove abrasive adhesive paper liner and press abrasive to vinyl-face sanding pad. Quick disc removal. 41 Short nap Long nap Hook-Face Pads Short nap pads for use with reattachable discs. Long nap pads for use with non-woven nylon discs. Non-Vacuum Pads Pad Dimensions Part Number Face Nap Screws Vinyl 4 93 mm (3-2/3") x Hook Short mm (7") Hook Long 4 Vacuum Pads Pad Dimensions Part Number Face Nap Screws 93 mm (3-2/3") x Vinyl mm (7") Hook Short 4

47 Dynaline Sanding Pads 10 mm (3/8") Thick, Medium Density Pads Pads mount with two screws NEW! Vinyl-Face Pads Ideal for PSA-type disc adhesion. Remove abrasive adhesive paper liner and press abrasive to vinyl-face sanding pad. Quick disc removal. Non-Vacuum Pads Short nap Long nap Hook-Face Pads Short nap pads for use with reattachable discs. Long nap pads for use with non-woven nylon discs. Loop-Face Pads Pads accept 3M Hookit II abrasives. Pad Dimensions Part Number Face Nap Screws Vinyl 2 70 mm (2-3/4") x Hook Short mm (8") Hook Long Vinyl 2 93 mm (3-2/3") x Hook Short mm (7") Hook Long 2 Vacuum Pads Pad Dimensions Part Number Face Nap Vacuum Holes 68 mm (2-3/4") x 196 mm (7-3/4") Loop 8 NEW! 70 mm (2-3/4") x Vinyl mm (8") Hook Short 6 93 mm (3-2/3") x Vinyl mm (7") Hook Short mm (11") File Board Sanding Pads 10 mm (3/8") Thick, Medium Density Pads Pads mount with two screws Vinyl-Face Pads Ideal for PSA-type disc adhesion. Remove abrasive adhesive paper liner and press abrasive to vinyl-face sanding pad. Quick disc removal. Short nap Long nap Hook-Face Pads Short nap pads for use with reattachable discs. Long nap pads for use with non-woven nylon discs. Non-Vacuum Pads Pad Dimensions Part Number Face Nap Vinyl 70 mm (2-3/4") x Hook Short 203 mm (8") Hook Long Vinyl 70 mm (2-3/4") x Vinyl 279 mm (11") Hook Short Hook Long 42

48 Dynafine Sanding Pads 10 mm (3/8") Thick, Medium Density Pads Fit all Dynafine sanders Pads mount with two screws NEW! Short nap Long nap Vinyl-Face Pads Ideal for PSA-type disc adhesion. Remove abrasive adhesive paper liner and press abrasive to vinyl-face sanding pad. Quick disc removal. Hook-Face Pads Short nap pads for use with reattachable discs. Long nap pads for use with non-woven nylon discs. Loop-Face Pads Pads accept 3M Hookit II abrasives. Round Non-Vacuum Pads Pad Dimensions Part Number Face Nap 51 mm (2") Dia Loop NEW! 76 mm (3") Dia Loop Triangular Non-Vacuum Pads Pad Dimensions Part Number Face Nap Vinyl 73 mm (2-7/8") x Hook Short 79 mm (3-1/8") Hook Long Tear Drop Non-Vacuum Pads Pad Dimensions Part Number Face Nap Vinyl 95 mm (3-3/4") x Hook Short 60 mm (2-3/8") Hook Long Wet Dynafine Sanding Pads 10 mm (3/8") Thick, Medium Density Pads Pads mount with two screws NEW! Vinyl-Face Pads Ideal for PSA-type disc adhesion. Remove abrasive adhesive paper liner and press abrasive to vinyl-face sanding pad. Quick disc removal. Hook-Face Pads Short nap pads for use with reattachable discs. Loop-Face Pads Pads accept 3M Hookit II abrasives. Non-Vacuum Pads Pad Dimensions Part Number Face Nap Loop 51 mm (2") Dia Vinyl Hook Short NEW! Loop 76 mm (3") Dia Vinyl Hook Short NEW! 43

49 Interface Pads and Pad Conversions Dynafoam Interface Pads Attaches between sanding pad and hook-face abrasive. Soft foam increases conformability allowing operator to easily follow contours. Converts standard pad into a fine finishing and finessing pad! Interface pad easily contours to most surfaces. Vinyl-to-Hook Conversions Thin sticky-back sheet adheres to current vinyl-face pad and accepts hook-face abrasives and hook-face interface pads. Vinyl-face pad Thin sticky-back sheet with hook-face bottom Hook-face pad Hook-face interface pad attaches between sanding pad and hook-face abrasive Hook-face abrasive For Random Orbital Sanders Non-Vacuum and Vacuum Part No. Diameter mm (3") Hook-face interface pad can be attached between sanding pad and hook-face abrasive Hook-face abrasive Thin sticky-back sheet adheres to current vinyl-face pad For Random Orbital Sanders Non-Vacuum and Vacuum Part No. Diameter Hook-face accepts abrasives and hook-face interface pads mm (3-1/2") mm (5") mm (6") For Dynafine Detail Sanders Part No. Diameter Tear Drop mm (3") mm (3-1/2") mm (5") For Dynafine Detail Sanders Part No. Diameter Tear Drop mm (8") Triangular mm (6") Triangular For Dynaline and Dynabug Sanders Part No. Diameter mm (2-3/4") x 279 mm (11") For the Dynaline mm (2-3/4") x 203 mm (8") For the Dynaline mm (3-2/3") x 178 mm (7") For the Dynaline and Dynabug For Dynaline and Dynabug Sanders Part No. Diameter mm (2-3/4") x 279 mm (11") For the Dynaline mm (2-3/4") x 203 mm (8") For the Dynaline mm (3-2/3") x 178 mm (7") For the Dynaline and Dynabug Hook-to-Vinyl Conversions Hook-face pad Thin velcro-backed sheet attaches to standard hook-face pad and accepts PSA-type abrasives Loop material attaches to standard hook-face sanding pad Non-Vacuum and Vacuum Part No. Diameter mm (5") mm (6") Premium vinyl-face for PSA-type abrasives 44

50 Mini-Dynorbital Sanding Heads For 1/4"-20 Female Thread Pads Accepts 76 mm (3") and smaller diameter sanding pads with 1/4"-20 female thread. Sanding Heads Tool Connection For Male Locking-Type Thread Pads Accepts 76 mm (3") and smaller dia. sanding pads with male locking-type threads such as 3M Roloc. Pad Connection Tool Connection Pad Connection Part Number Tool Connection Pad Connection /4"-28 Male 1/4"-20 Male /8"-24 Female 1/4"-20 Male /4"-20 Female 1/4"-20 Male Mini-Dynorbital Hook-Face P/N ,500 RPM maximum. For use with reattachable discs. Medium, Dual Density P/N ,000 RPM maximum. For wet sanding operations. 6 mm thick sponge, 60 durometer rubber. Medium, Single Density P/N ,000 RPM maximum. For wet sanding operations. Single density, 8 mm thick sponge. Soft Density P/N ,000 RPM maximum. 6 mm thick sponge, vinyl-face. Compounds Finesse Sanding Creme A sanding compound for metal, fiberglass and composites. Use with fine-grade sanding discs. Part Number ml (4 oz.) Part Number Tool Connection Pad Connection /4"-28 Male Locking-Type Female Thread /8"-24 Female Locking-Type Female Thread 54030* 1/4"-28 Male Locking-Type Female Thread * For Rotary Sanding Roloc is a registered trademark of 3M Company Sanding Pads 19 mm (3/4") Dia. Sanding Pads Part Number Max. RPM Material Density Face Thread ,000 Foam Medium Rubber 1/4"-20 Female ,000 Foam Soft Vinyl 1/4"-20 Female ,000 Nylon Hard Hook 1/4"-20 Female NOTE: To mount pads that have 1/4"-20 female thread directly to tool for conventional rotary action, use Adapter 32 mm (1-1/4") Dia. Sanding Pads Part Number Max. RPM Material Density Face Thread ,000 Foam Medium Rubber 1/4"-20 Female ,000 Nylon Soft Vinyl Locking-Type ,000 Nylon Medium Rubber Locking-Type ,000 Urethane Soft Vinyl 1/4"-20 Female ,000 Foam Soft Vinyl 1/4"-20 Female ,500 Nylon Hard Hook 1/4"-20 Female NOTE: To mount pads that have 1/4"-20 female thread directly to tool for conventional rotary action, use Adapter ALU Cream For polishing aluminum and chromium surfaces on motorcycles; provides high gloss finish. Part Number Part Number ml (0.07 gal.) 1,000 ml (0.26 gal.) Part Number ml (1 qt.) Part Number l (1 gal.) Dynabrade Glaze For use with slow-speed tools to achieve a high gloss after compounding. Part Number Part Number ml (4 oz.) 946 ml (1 qt.) 45

51 Threaded Adapters NPT Threaded Adapters User assumes all responsibility for using adapters safely Part Number Exposed Threads Length Wrench Flats aa bb (aa) /4" NPT Female 1/8" NPT Male 25 mm (1") (bb) /8" NPT Female 1/4" NPT Male 32 mm (1-1/4") cc (cc) /2" NPT Female 3/8" NPT Male 44 mm (1-3/4") Collet-to-Thread Adapters aaa bbb User assumes all responsibility for using adapters safely Part Number Exposed Threads Shank Dia. Length Wrench Flats (aaa) /4" Shank 1/4"-20 Male 1/4" 32 mm (1-1/4") 11 mm (bbb) /4" Shank 1/4"-20 Female 1/4" 38 mm (1-1/2") Threaded Adapters a c b d User assumes all responsibility for using adapters safely Part Number Exposed Threads Length Wrench Flats (a) M x 8 Female 3/8"-24 Male 19 mm (3/4") 12 mm (b) M x 8 Female 3/8"-24 Male 35 mm (1-3/8") 11 mm (c) /4"-28 Male 1/4"-20 Male 30 mm (1-3/16") 14 mm e f (d) /8"-24 Male 1/2"-20 Male 25 mm (1") 19 mm (e) /8"-24 Female M14 x 2 Male 25 mm (1") 19 mm (f) /8"-24 Female 1/4"-20 Male 27 mm (1-1/16") 14 mm g h (g) /8"-24 Female 3/8"-24 Male 25 mm (1") 9 mm i j (h) /8"-24 Female 3/8"-24 Male 25 mm (1") 17 mm (i) /8"-24 Female 1/2"-20 Male 51 mm (2") 16 mm k l (j) /8"-24 Female 1/2"-20 Male 51 mm (2") 16 mm (k) /8"-24 Female 5/8"-11 Male 25 mm (1") 17 mm m n (l) /8"-24 Female 5/8"-11 Male 35 mm (1-3/8") 17 mm (m) /8"-24 Female 5/8"-11 Male 38 mm (1-1/2") 24 mm o q r p (n) /8"-24 Female 5/8"-11 Male 51 mm (2") 3/4" (o) /8"-24 Female 5/8"-11 Male 64 mm (2-1/2") 3/4" (p) /8"-24 Female 1/4"-20 Female 38 mm (1-1/2") 16 mm (q) /8"-24 Female 5/16"-24 Female 25 mm (1") 17 mm s t (r) /2"-20 Female 5/8"-11 Male 44 mm (1-3/4") 19 mm (s) /8"-11 Female 5/16"-24 Female 41 mm (1-5/8") 19 mm (t) /8"-11 Female 5/8"-11 Male 51 mm (2") 19 mm u (u) /8"-11 Female 5/8"-11 Male 102 mm (4") 19 mm 46

52 Repair and Tune-Up Accessories Replacement Drop-In Motors For Dynorbital-Spirit Allows quick and easy replacement; no motor adjustments needed. Follow maintenance procedures described in parts page. Diameter 76 mm (3") 89 mm (3-1/2") 127 mm (5") 152 mm (6") Orbit Dia. Models Dia. Models Dia. Models Dia. Models 10 mm (3/8") mm (3/16") mm (3/32") Full Service Repair Kit Special tools for proper disassembly/assembly of the Dynorbital-Spirit. Includes: Repair Collar Lock Ring Wrench Bearing Puller Bearing Press Tool Bearing Puller mm Hex Wrench Drop-In Motor Repair Kit Special tools for proper disassembly/assembly of the Dynorbital-Spirit drop-in motor. Includes: Repair Collar Lock Ring Wrench DynaZip Wheels and Hub Assembly For Use with DynaZip Surface Preparation Tool 4" (102 mm) Diameter Wire Wheels All wire wheels have band width of 3/4" (19 mm). NOTE: Wire wheels only; no hub included. Bristle Width Part No. Grade Band Tip Type 1/2" (13 mm) Coarse Black Bent 3/4" (19 mm) Coarse Red Bent Wheel Hub Assembly Part Number Assembly accepts both wire wheels and eraser wheels Tune-Up Kit Tune-up kit contains high and medium wear parts Wrench Replacement 26 mm open-end wrench for changing sanding pads. Brush Ring Use with Palm-Style Random Orbital Sanders Part Number Plastic ring with angled brushes fits into the lip seal shroud of Dynabrade s 127 mm (5") and 152 mm (6") Palm-Style Random Orbital Sanders. Pressure is adjustable by using 0.4 mm plastic washers (P/N 95859) Reduces spinning of pad and decreases risk of abrasive aggressiveness. - Improves dust collection. - Spinning stops quicker when throttle lever is released. Decal Removal Wheels Eraser Wheel Eraser wheel only; no hub included Eraser Wheel with Hub Eraser Wheel with mated Wheel Hub Assembly. Bow-Type Handle Use with Model Electric Polisher Part Number Focuses the force applied by the operator above the centerline of the polishing pad, thereby providing greater comfort to the operator and minimizing hand and arm fatigue. Plastic handle mounts onto the gear box with two M8 x16 screws. Ideal for both left and right hand operation.

53 Notes

54 Notes

55

56 DYNABRADE EUROPE S.à r.l. Zone Artisanale L-5485 Wormeldange Haut Luxembourg Telephone: Fax: DYNABRADE, INC. 2006

Palm-Style Mini-Orbital Offset Mini-Orbital...55 Angle-Head Mini-Dynorbital...56 Right Angle Mini-Orbital...57 Electric Dynorbital...

Palm-Style Mini-Orbital Offset Mini-Orbital...55 Angle-Head Mini-Dynorbital...56 Right Angle Mini-Orbital...57 Electric Dynorbital... Dynorbital-Spirit...46 HiVac Dynorbital-Spirit...48 Mesh Abrasive Systems...49 Dynorbital Supreme...50 Two-Hand Dynorbital...52 11" Dia. Dynorbital...53 Palm-Style Mini-Orbital...54 7 Offset Mini-Orbital...55

More information

Portable Air Tools for the Value-Minded Professional

Portable Air Tools for the Value-Minded Professional Reorder No. D05.09 Red Portable Air Tools for the Value-Minded Professional Includes Abrasive Belt Tools, Die Grinders, Disc Sanders, Buffers and More DynaZip Air Tools (See Page 2) 18255 DynaZip Air Tool

More information

Dynabuffer...82 Two-Step Repair System " Dia. Buffers "-8" Buffers...87

Dynabuffer...82 Two-Step Repair System  Dia. Buffers -8 Buffers...87 Dynabuffer...82 Two-Step Repair System...83 3" Dia. Buffers...84 5"-8" Buffers...87 6"-8" Buffers...88 Straight-Line Buffer...89 Electric Buffer...89 Random Orbital Polishers/Head Kit...90 82 Dynabuffer

More information

Reorder No. EUR11.12

Reorder No. EUR11.12 Reorder No. EUR11.12 CATALOGUE & PRICE LIST FOR DISTRIBUTORS REFINISH SOLUTIONS AUTOMOTIVE AFTERMARKET 2016 RESHAPING YOUR WORLD WITH WORLDWIDE MARKET LEADERSHIP WORLD CLASS PRODUCT INNOVATIONS CUTTING

More information

MEMBER. Try our new toll-free Consumer Information Number: DYNABRADE

MEMBER. Try our new toll-free Consumer Information Number: DYNABRADE Reorder No. A03.01 2 DYNABRADE FULL ONE-YEAR WARRANTY Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from

More information

Dynabrade Vacuum Tools and Accessories

Dynabrade Vacuum Tools and Accessories Dynabrade Vacuum Tools and Accessories Breathe Easy and Work Safe with Dynabrade Reorder No. D12.16 Dynabrade Vacuum Tools... Dynabrade s complete line of Vacuum Tools and Accessories efficiently capture

More information

INDUSTRIAL POWER TOOLS

INDUSTRIAL POWER TOOLS Reorder No. D10.10 INDUSTRIAL POWER TOOLS Continued Leadership In Portable Abrasive Power Tool Technology www.dynabrade.com INTRODUCTION Who We Are Since 1969, Dynabrade has earned a reputation of excellence

More information

RANDOM ORBITAL SANDERS

RANDOM ORBITAL SANDERS RANDOM ORBITAL SANDERS Dynorbital Supreme...148 Wet Dynorbital Supreme...150 Dynorbital Silver Supreme...152 Dynorbital-Spirit...154 HiVac Dynorbital-Spirit...156 Swirl-Free Checklist...157 Two-Hand Dynorbital...157

More information

Two-Hand Tool Series from Dynabrade

Two-Hand Tool Series from Dynabrade Two-Hand Tool Series from Dynabrade Random Orbital, Gear-Driven and Dual Action Sanders Reorder No. D04.05 Efficient Pneumatic Motor Offers Increased Power Advanced Design Allows Optimum Comfort and Control

More information

Two-Step System for Clear Coat Repair

Two-Step System for Clear Coat Repair Two-Step System for Clear Coat Repair With Buffing Time REDUCED by up to 40%! Reorder No. D10.09 NEW Random Orbital Sander and Dynabuffer with Exciting Innovations Proven Method for Repairing Surface Defects

More information

Accessories Intro.qxd:Layout 1 9/27/06 5:50 PM Page 1

Accessories Intro.qxd:Layout 1 9/27/06 5:50 PM Page 1 Accessories Intro.qxd:Layout 1 9/27/06 5:50 PM Page 1 Air Supply Accessories...160 Arbors...186 Carbide Burrs and Carbide Burr Kits...189 Collets and Inserts...190 Contact Wheels and Assemblies...196 Couplers,

More information

.4 hp Die Grinders & Disc Sanders

.4 hp Die Grinders & Disc Sanders .4 hp Die Grinders & Disc Sanders NEW Lightweight Ergonomic Design! Reorder No. D12.14 Ideal for Rapid Material Removal, Sanding, Deburring, Finishing Right Angle, 7 Offset & Angle-Head s Plus Angle-Head

More information

3,200 RPM Angle-Head WARNING

3,200 RPM Angle-Head WARNING Model: 50046 Angle-Head Kit 54002 Mini-Dynorbital Sander 54003 Mini-Dynorbital Sander 50223 2" Disc Sander 51091 Die Grinder 53026 Drill 50047 3" Buffer 50070 Finesse Sanding Kit Parts Page Reorder No.

More information

Dynafile...8 Dynafile II hp Dynafile II...12 Vacuum Dynafile II...13 Electric Dynafile II...13 Mini-Dynafile II...16

Dynafile...8 Dynafile II hp Dynafile II...12 Vacuum Dynafile II...13 Electric Dynafile II...13 Mini-Dynafile II...16 Dynafile...8 Dynafile II...11.4 hp Dynafile II...12 Vacuum Dynafile II...13 Electric Dynafile II...13 Mini-Dynafile II...16 Dynafile III...18 Dynabelter...22 Dynangle...25 Dynangle II...26 Take-About Sander...27

More information

CCESSORIES OOL A AIR T 222

CCESSORIES OOL A AIR T 222 AIR TOOL ACCESSORIES AIR TOOL ACCESSORIES Air Line Assemblies - Flexible, Swivel-Style...226 Air Line Assemblies - Lightweight...225 Air Line Fittings...227 Air Motor Tune-Up Kits...267 Arbors, Accessories...248

More information

Model. Reach into areas as small as 3/8". Model. Max. Air Flow SCFM (L/Min)

Model. Reach into areas as small as 3/8. Model. Max. Air Flow SCFM (L/Min) The Dynafile Original The Best Tracking Abrasive Belt Tool in the World! 14000 For 24" Long Belts World-famous Dynafile replaces tedious hand filing and sanding. Grind, deburr, blend, polish, finish and

More information

Sanders, Buffers & Polishers Introduction

Sanders, Buffers & Polishers Introduction Sanders, Buffers & Polishers Introduction Dotco sanders, buffers and polishers are available in a variety of styles and power ratings to provide flexibility in choosing the best tool for the job. Disc

More information

Pencil Grinders hp, 0.4 hp Die Grinders hp Die Grinders hp Die Grinders...101

Pencil Grinders hp, 0.4 hp Die Grinders hp Die Grinders hp Die Grinders...101 Pencil Grinders...92 0.33 hp, 0.4 hp Die Grinders...95 0.4 hp Die Grinders...96 0.5 hp Die Grinders...101 0.55 hp Die Grinder...104 0.7 hp Die Grinders...105 1.0 hp Die Grinders...107 92 Pencil Grinders

More information

WARNING. Air-Powered, 2,400 RPM. AUTOMOTIVE Parts Page Reorder No. APD01 06 Effective April, 2001 Supercedes APD97 02 Palm-Style Buffer/Sander

WARNING. Air-Powered, 2,400 RPM. AUTOMOTIVE Parts Page Reorder No. APD01 06 Effective April, 2001 Supercedes APD97 02 Palm-Style Buffer/Sander Models: 090 Buffer 09 Mini Orbital Sander 09 Versatility Kit 09 4"-5" Buffer AUOMOIVE Parts Page Reorder No. APD0 06 Effective April, 00 Supercedes APD97 0 Palm-Style Buffer/Sander Air-Powered,,400 RPM!

More information

Dynorbital Supreme II Update Notice

Dynorbital Supreme II Update Notice For Use With All: Dynorbital Supreme II Models Parts Page Reorder No. PD01 67 Effective July, 2001 Dynorbital Supreme II Update Notice Balancer Shaft Revision OLD Configuration NEW Configuration 1 2 A

More information

Vacuum Models Central Vacuum Pencil Grinder hp Vacuum Die Grinders hp Vacuum Die Grinders hp Vacuum Die Grinders...

Vacuum Models Central Vacuum Pencil Grinder hp Vacuum Die Grinders hp Vacuum Die Grinders hp Vacuum Die Grinders... Non-Vacuum s Pencil Grinders...47 Quick-Change Pencil Grinder...49.4 hp Die Grinders...52.5 hp Die Grinders...59.55 hp Die Grinder...62.7 hp Die Grinders...63 1 hp Die Grinders...67 Vacuum s Central Vacuum

More information

Dynabrade Portable Abrasive Belt Tools

Dynabrade Portable Abrasive Belt Tools Dynabrade Portable Abrasive Belt Tools Grind, Deburr, Blend, Clean, Polish and Finish Reorder No. D08.02R We offer a diverse line of products to help you get the job done. With expert knowledge, service

More information

ABRASIVE BELT TOOLS. APTOOL.RU Phone: +7 (495)

ABRASIVE BELT TOOLS. APTOOL.RU Phone: +7 (495) ABRASIVE BELT TOOLS APTOOL.RU Phone: +7 (495) 723-19-55 ABRASIVE BELT TOOLS The Dynafile Original Air-Powered Abrasive Belt Tool The Best Tracking Abrasive Belt Tool in the World! 14000 For 24" Long Belts

More information

95979 Pin Lever O-Ring (2) Valve Stem Speed Regulator or Recessed Speed Regulator

95979 Pin Lever O-Ring (2) Valve Stem Speed Regulator or Recessed Speed Regulator Models: 57000-3-1/2" Non-Vacuum 57023-5" Vac-Ready w/overskirt 57001-3-1/2" Basic Vacuum 57024-5" Central Vac-Ready w/overskirt 57002-3-1/2" Deluxe Vacuum 57026-6" Non-Vacuum 57003-3-1/2" Vac-Ready 57027-6"

More information

Electric Portable Dry Vacuums

Electric Portable Dry Vacuums Electric Portable Dry Vacuums For use with air tools setup for two-tool operation. A cost-effective solution versus overhead central-vac systems. Quiet operation only 76 db(a). Variable Vacuum Control

More information

Dynaswivel. Air Line Connectors. Ball-Swivel Plug. Never Fight an Air Tool Again! For Use with Most Air Tools THE PROBLEM THE SOLUTION

Dynaswivel. Air Line Connectors. Ball-Swivel Plug. Never Fight an Air Tool Again! For Use with Most Air Tools THE PROBLEM THE SOLUTION Dynaswivel Air Connectors Never Fight an Air Tool Again! For Use with Most Air Tools THE PROBLEM Aluminum and Stainless Steel Construction Single Pivot Right angle single-pivot swivels 360 at one location.

More information

WARNING DYNABRADE. Air Powered Abrasive Belt Machine

WARNING DYNABRADE. Air Powered Abrasive Belt Machine For Serial No.9I1001 and Higher Parts Page Reorder No. PD00 50 Effective June, 2000 Supercedes PD96 16 66402 Tool Post Grinder Instruction Manual Air Powered Abrasive Belt Machine! WARNING Always operate,

More information

AIR SANDERS & POLISHERS

AIR SANDERS & POLISHERS AIR SANDERS & POLISHERS The most complete line of air finishing tools. Ingersoll Rand finishing tools are designed for long-life and swirl-free finishes. 49 4151-HL High Performance 150 mm Random Orbital

More information

FINISHING. Finishing Index. Sanders Polishers Finishing Accessories

FINISHING. Finishing Index. Sanders Polishers Finishing Accessories Finishing Index Sanders................... 33-34 Polishers...................... 34 Finishing Accessories........ 35-38 ACCESSORIES SPECIALTY PERCUSSIVE FINISHING ABRASIVE ASSEMBLY DRILLS The Best Way

More information

Dynabelter WARNING. Parts Page Reorder No. PD01 05 Effective January, 2001 Supersedes PD Models: Standard Duty/Finisher

Dynabelter WARNING. Parts Page Reorder No. PD01 05 Effective January, 2001 Supersedes PD Models: Standard Duty/Finisher Parts Page Reorder No. PD01 05 Effective January, 2001 Supersedes PD94 53 Models: 11462 Standard Duty/Finisher Dynabelter 11475 Standard Duty 11476 Heavy Duty 1" Wide Abrasive Belt Capacity! WARNING 1

More information

DYNASTRAIGHT For Grinding, Cleaning and Polishing Works on Stainless Steel, Aluminum, Composites

DYNASTRAIGHT For Grinding, Cleaning and Polishing Works on Stainless Steel, Aluminum, Composites DYNASTRAIGHT For Grinding, Cleaning and Polishing Works on Stainless Steel, Aluminum, Composites 950 RPM Model 13200.7 hp Model 13500 1 hp 13071 Combo Arbor for up to 3" wide wheels with a 5/8" or 1" dia.

More information

Supplying the Aerospace, Defense & Metal Working Industries Since 1951!

Supplying the Aerospace, Defense & Metal Working Industries Since 1951! Toll Free US & Canada: 800-645-8180 Eastern Division 60 Fleetwood Ct., Ronkonkoma, NY 11779-6907 Telephone: (631) 471-3300 Fax: (631) 471-3308 Western Division 1219 W. Mahalo Place, Rancho Dominguez, CA

More information

KEY. Oil. Grease. Loctite/Hernon: L 2 = Hernon #940. Torque: N m x 8.85 = In. - lbs. T 2 = 17 N m, T 3 = 23 N m Threaded Insert

KEY. Oil. Grease. Loctite/Hernon: L 2 = Hernon #940. Torque: N m x 8.85 = In. - lbs. T 2 = 17 N m, T 3 = 23 N m Threaded Insert Model: 11000 11001 Versatility Kit 11003 w/benchmount O L T Oil KEY G Grease Loctite/Hernon: L 2 = Hernon #940 Torque: N m x 8.85 = In. - lbs. T 2 = 17 N m, T 3 = 23 N m Parts Page Reorder No. PD97 01

More information

Sanders & Polishers. Sanders & Polishers

Sanders & Polishers. Sanders & Polishers 35 Non-Vacuum (NV) Self Vacuum (SV) Central Vacuum (CV) Select the right random orbital for your applications MODEL PAD SIZE ORBIT PAD TYPE 2 Handed in. mm in. mm Non- Vacuum (NV) CP7225-3 3 75 3/32 2.5

More information

Accessory Items ACCESSORIES GRINDING

Accessory Items ACCESSORIES GRINDING Accessory Items The convenience of one stop shopping is provided through the selection of accessories offered by United Abrasives to complement and match our product offering. All of the accessories carried

More information

Application Guide DISTRIBUTED BY:

Application Guide DISTRIBUTED BY: DISTRIBUTED BY: Application Guide Meguiar s International Headquarters: Suite 6-7, 20/F Marina House, 68 Hing Man Street, Shaukeiwan, Hong Kong Phone: 852-2967-0202 Fax: 852-2967-6968 MV-81 MV-82 MV-83

More information

Dynabrade Vacuum Cut-Off Wheel Tools

Dynabrade Vacuum Cut-Off Wheel Tools Dynabrade Vacuum Cut-Off Wheel Tools Efficiently Capture Dust and Debris While Cutting Reorder No. D07.12 Ideal for Effective Cutting through Fiberglass, Composites, More Vacuum Shroud Diverts Dust and

More information

Angle & Vertical Grinders

Angle & Vertical Grinders Angle & Vertical Grinders Lightweight aluminium housing to help reduce operator fatique. Designed to handle a variety of applications from fine deburring to heavy grinding. Equipped for Type 27 depressed

More information

For Serial No. 2Axxxx and Higher For Type A Tools Serial No. xxxxxxa and Higher

For Serial No. 2Axxxx and Higher For Type A Tools Serial No. xxxxxxa and Higher 60,000 RPM Models: Model 51700 (1/8" Collet) Model 51701 (3mm Collet) Model 51702 (3/32" Collet) Model 51770 (1/16" Collet) 50,000 RPM Models: Model 51703 (1/8" Collet) Model 51704 (3mm Collet) Model 51705

More information

3M Industrial Paint Preparation and Finishing Solutions. Redefining. Finish. the. Line

3M Industrial Paint Preparation and Finishing Solutions. Redefining. Finish. the. Line 3M Industrial Paint Preparation and Finishing Solutions the Redefining Finish Line Choose 3M products for consistent quality results. Paint Preparation Abrasives...3 5 Tools... 5 Accessories...5 7 Paint

More information

New products at a glance

New products at a glance PROFESSIONAL CATALOG ADDENDUM New products at a glance 2015 NEW PRODUCTS M305 ULTRA FINISHING DURABLE GLAZE M30516 16 oz. M30564 64 oz. VSLM305 Secondary Label Fast wipe on, wipe off Silicone-free high

More information

3M Power Tools, Abrasives and Accessories. 3M Power Tools. Abrasives Tools from the Abrasives Experts

3M Power Tools, Abrasives and Accessories. 3M Power Tools. Abrasives Tools from the Abrasives Experts 3M Power Tools, Abrasives and Accessories 3M Power Tools Abrasives Tools from the Abrasives Experts 3M Power Tool Warranty Warranty and Limited Remedy: 3M warrants this tool against defects in workmanship

More information

Models: Standard Machine, NWN Machine Screw Guide Screw Screw Button Screw Support Rod

Models: Standard Machine, NWN Machine Screw Guide Screw Screw Button Screw Support Rod Effective Serial Number Reference Table Model Number Serial Number 40320, 40321 36300 40326 1284 40330 3001 40335 1129 Models: 40320 Standard Machine 40326 20-1/2" Long Belt Machine 40330 Vacuum Machine

More information

WE LISTEN. WE OBSERVE. WE OPTIMIZE. REBEL 2.8 HP SERIES 7" & 9" GRINDERS AND SANDERS

WE LISTEN. WE OBSERVE. WE OPTIMIZE. REBEL 2.8 HP SERIES 7 & 9 GRINDERS AND SANDERS WE LISTEN. WE OBSERVE. WE OPTIMIZE. REBEL 2.8 HP SERIES 7" & 9" GRINDERS AND SANDERS REBEL 2.8 HP SERIES 7" & 9" GRINDERS AND SANDERS Rebel series grinders and sanders are powerful tools designed to overcome

More information

New products at a glance

New products at a glance PROFESSIONAL CATALOG ADDENDUM New products at a glance MEGUIAR S PROFESSIONAL CATALOG ADDENDUM 2015 NEW PRODUCTS M305 ULTRA FINISHING DURABLE GLAZE Fast wipe on, wipe off Silicone-free high gloss finish

More information

High-Performance. ShineMateTM Auto Polishing Tool System. CATALOGUE Issue 6.1

High-Performance. ShineMateTM Auto Polishing Tool System. CATALOGUE Issue 6.1 High-Performance Auto Polishing Tool System ShineMateTM Auto Polishing Tool System CATALOGUE Issue 6.1 ShineMate, tools for polishing artist From bodyshops' refinishing process, to high gloss paint care

More information

Supplying the Aerospace, Defense & Metal Working Industries Since 1951!

Supplying the Aerospace, Defense & Metal Working Industries Since 1951! Toll Free US & Canada: 800-645-8180 Eastern Division 60 Fleetwood Ct., Ronkonkoma, NY 11779-6907 Telephone: (631) 471-3300 Fax: (631) 471-3308 Western Division 1219 W. Mahalo Place, Rancho Dominguez, CA

More information

3M Industrial Products. Abrasives and Power Tools for Welders. Welding Solutions

3M Industrial Products. Abrasives and Power Tools for Welders. Welding Solutions 3M Industrial Products Abrasives and Power Tools for Welders Welding Solutions What s New for2011 3 4 1 2 5 6 1 2 3 3M Cubitron II Fibre Discs 987C The coolest way to increase productivity. If you work

More information

Finish Line. Redefining The. NEW 3M Elite Series Air-Powered Random Orbital/Orbital Sanders NEW 3M Electric Random Orbital Sanders

Finish Line. Redefining The. NEW 3M Elite Series Air-Powered Random Orbital/Orbital Sanders NEW 3M Electric Random Orbital Sanders NEW 3M Elite Series Air-Powered Random Orbital/Orbital Sanders NEW 3M Electric Random Orbital Sanders Redefining The Finish Line 3M Elite Series Sanders NEW Elite Series Air-Powered Sanders and NEW Electric

More information

DYNABRADE.COM. Reorder No. D12.01

DYNABRADE.COM. Reorder No. D12.01 DYNABRADE.COM Reorder No. D12.01 Abrasive Belt & Finishing Tools Abrasive Belt Tools Dynafile...10 Dynafile II...13.4 hp Dynafile II...14 Vacuum Dynafile II...15 Electric Dynafile II...15 Mini-Dynafile

More information

Air Tools. 1/4 Angle Die Grinder

Air Tools. 1/4 Angle Die Grinder Air Tools Everbrite Abrasive Pte Ltd Blk 5026, Ang Mo Kio Industrial Park 2, #01-91, Singapore 569529 Tel: 64847582 Fax: 64849570 hlp://everbriteabrasive.net email:enquiry@everbriteabrasive.net 1/4 Angle

More information

Features and Specifications for Impact Wrenches

Features and Specifications for Impact Wrenches Pneumatic Air Tools Version 2017 Revised 06/2017 Email your order to: sales@polyconn.com or fax to (763) 398-2590. www.polyconn.com. Questions call: (763)559-0388 3062 Ranchview Lane North. Plymouth, MN

More information

67 YEARS OF AMERICAN INGENUITY

67 YEARS OF AMERICAN INGENUITY March 2018 67 YEARS OF AMERICAN INGENUITY Ultra Light Weight/ Orbital Sanding 3 GENERATIONS & COUNTING Ultra Light Weight Sanding Industrial Light Weight / Low Proole Sanding Random Orbital Water Sanding

More information

15003, Tool Assembly. Note: Shaded parts represent Housing Assembly Vacuum Tool Assembly

15003, Tool Assembly. Note: Shaded parts represent Housing Assembly Vacuum Tool Assembly For Serial No. 1B1000 and Higher Parts Page Reorder No. PD01 29 Effective March, 2001 Supercedes PD97 64 Models: Mini-Dynafile II 15002 Vacuum ool 15003 Basic ool with Drive Wheel 15006 Versatility Kit

More information

Effective January, 2000 Supercedes PD95 54 Models: 3 = Loctite #242, A 9 = Loctite #587. Models: Standard Machine, NWN Machine 16 A 9

Effective January, 2000 Supercedes PD95 54 Models: 3 = Loctite #242, A 9 = Loctite #587. Models: Standard Machine, NWN Machine 16 A 9 For Serial No. 9K2915 and Higher Parts Page Reorder No. PD00 05 O Oil: O 1 = Air Lube KEY Effective January, 2000 Supercedes PD95 54 Models: G Grease: = Loctite #771 40320 Standard Machine A Adhesive:

More information

3M Power Tools, Abrasives and Accessories. Optimize. Performance. With The Perfect. System

3M Power Tools, Abrasives and Accessories. Optimize. Performance. With The Perfect. System 3M Power Tools, Abrasives and Accessories Optimize Performance With The Perfect System 3M Power Tools A full family of innovative tools to optimize your abrasive performance & maximize your comfort. n

More information

Air Finishing Tools CP778. Heavy Duty Hi-Speed Sander

Air Finishing Tools CP778. Heavy Duty Hi-Speed Sander Air Finishing Tools Finishing work provides a wide range of challenges and we have a complete line of sanders, buffers and polishers for every application from heavy material removal to fine finishing.

More information

POLISHER USER S GUIDE

POLISHER USER S GUIDE DUAL ACTION POLISHER USER S GUIDE Safety Notes Features INSTRUCTIONS Maintenance & Care DUAL ACTION POLISHER TABLE OF CONTENTS Features...2 Safety Notes...3 Basic Instructions...4 Maintenance & Care...6

More information

3M Automotive Aftermarket 3M Paint Finishing Solutions.

3M Automotive Aftermarket 3M Paint Finishing Solutions. 3M Automotive Aftermarket 3M Paint Finishing Solutions. Saving you time on the path to the perfect finish. Achieve a perfect finish with 3M s best finishing systems. 3M Trizact Abrasives 3M Trizact Abrasives

More information

Machine Deals. The Complete 3M System: The Right Machine + The Right Abrasive + The Right Accessory = Outstanding Result

Machine Deals. The Complete 3M System: The Right Machine + The Right Abrasive + The Right Accessory = Outstanding Result Machine Deals. Industries that work with metal face many different demands but they all share the same needs to raise quality levels and reduce production times and costs whilst achieving demanding standards.

More information

Automotive Refinishing

Automotive Refinishing $9.95 USD Automotive Refinishing www.mirkacollision.us sanding v3.1 For over 30 years, Mirka Abrasives, Inc. has continually raised the performance bar through the development of innovative products and

More information

Ergonomic design for comfort. Reduced vibration. Twin hammer impact mechanism. Part No. Maximum Torque Free Speed Weight Ave Air Consumption

Ergonomic design for comfort. Reduced vibration. Twin hammer impact mechanism. Part No. Maximum Torque Free Speed Weight Ave Air Consumption 3/8 Impact wrench The smallest in PCL s range of Prestige Impact Wrenches. The 3/8 Impact Wrench is designed for professional heavy duty use, with an ergonomically designed soft grip handle and a lightweight

More information

TABLE OF CONTENTS PAGE NO. PAGE NO. GRINDERS & CUT-OFF TOOLS 3/8 IMPACT WRENCHES 1/2 IMPACT WRENCHES DRILLS HAMMERS 3/4 IMPACT WRENCHES

TABLE OF CONTENTS PAGE NO. PAGE NO. GRINDERS & CUT-OFF TOOLS 3/8 IMPACT WRENCHES 1/2 IMPACT WRENCHES DRILLS HAMMERS 3/4 IMPACT WRENCHES The AIRCAT line represents the most significant advances in the performance of pneumatic power tools in nearly 30 years. Founded in 1998, our tool line has a substantially reduced level of noise while

More information

3M Collision Repair Solutions. 3M Abrasives and Power Tools. Cutting & Grinding. for Body Techs

3M Collision Repair Solutions. 3M Abrasives and Power Tools. Cutting & Grinding. for Body Techs 3M Collision Repair Solutions 3M Abrasives and Power Tools Cutting & Grinding for Body Techs 3M Disc Sander Ideal for general metal fabrication applications, including grinding, blending, weld leveling

More information

Dynafile III. Tool Assembly. Parts Page Reorder No. PD05 16 Effective March, Models:

Dynafile III. Tool Assembly. Parts Page Reorder No. PD05 16 Effective March, Models: Parts Page Reorder No. PD05 16 Effective March, 2005 Models: Dynafile III 15400 Basic ool w/11206 Contact Arm 15401 Basic ool w/11287 Contact Arm Air Motor and Machine Parts Always operate, inspect and

More information

Slow Speed Dynafile II

Slow Speed Dynafile II For Serial No. 1D1000 and Higher Parts Page Reorder No. PD01 54 Effective June, 2001 Slow Speed Dynafile II Models: 40381 Slow Speed Dynafile II Air Motor and Machine Parts! WARNING Always operate, inspect

More information

Automotiveabrasiveproducts

Automotiveabrasiveproducts Automotiveabrasiveproducts ISO 9000 Commitment for Quality With more than 80 years of integrated manufacturing experience, FANDELI has been a major producer of high quality sandpaper serving automotive

More information

Optimize. Finishing Results. 3M Power Tools, Abrasives and Accessories. New The Right Tools The Right Accessories The Right Abrasives

Optimize. Finishing Results. 3M Power Tools, Abrasives and Accessories. New The Right Tools The Right Accessories The Right Abrasives 3M Power Tools, Abrasives and Accessories Optimize Finishing Results New The Right Tools The Right Accessories The Right Abrasives Air-Powered Orbital & Disc Pads, Tool Kits Stikit, Hookit, Hookit II,

More information

PUMA RANGE OF AIR TOOLS

PUMA RANGE OF AIR TOOLS Type G / ATAT-3170 3mm Micro Pencil Grinder PUMA RANGE OF AIR TOOLS Now with new Safety levers. Better quality & Lower prices! ATAT-7032 6mm Mini Die Grinder ATAT-7033 6mm Straight Die Grinder ATAT-7033L

More information

Optimize. Finishing Results. 3M Power Tools, Abrasives and Accessories. New The Right Tools The Right Accessories The Right Abrasives

Optimize. Finishing Results. 3M Power Tools, Abrasives and Accessories. New The Right Tools The Right Accessories The Right Abrasives 3M Power Tools, s and Accessories Optimize Finishing Results New The Right Tools The Right Accessories The Right s Air-Powered Orbital & Disc Pads, Tool Kits Stikit,, Random Orbital Sanders & Sanding Tools

More information

Breakthrough Technology for a New Level of Auto Paint Protection!

Breakthrough Technology for a New Level of Auto Paint Protection! Breakthrough Technology for a New Level of Auto Paint Protection! PASTE WAX Pre-softened paste wax spreads on and buffs off easily. Removes fine swirls and scratches, giving paint deep color and shine.

More information

Dotco Drill Specifications

Dotco Drill Specifications Dotco Drill Specifications Speed Drill Diameter Type Weight Length Head Height Drill Chuck rpm (Capacity) (Housing) kg mm mm Size Air Inlet NPT Series 15LF straight - (300 Watt) 15LF081-38+ 5300 1/4" C

More information

3M Overhaul Service Kit

3M Overhaul Service Kit SERVICE INSTRUCTIONS FOR 3M 12,000 RPM 5 in. (127 mm) and 6 in. (150 mm) RANDOM ORBITAL SANDERS 3M Overhaul Service Kit The part number 20347, 3M Overhaul Service Kit, contains all the replacement parts

More information

FAST CORRECTING CREAM CORRECTING CREAM PERFECTING CREAM FINISHING SEALANT

FAST CORRECTING CREAM CORRECTING CREAM PERFECTING CREAM FINISHING SEALANT CORRECTING REMOVING MODERATE TO SEVERE DEFECTS MOST AGGRESSIVE PERFECTING REFINING & ENHANCING GLOSS PROTECTING PERFECTING & PROTECTING LEAST AGGRESSIVE FAST CORRECTING CREAM CORRECTING CREAM PERFECTING

More information

REV Random Orbital Floor Scrubbers

REV Random Orbital Floor Scrubbers A revolution in floor scrubbing. REV Random Orbital Floor Scrubbers Smart cleaning. THE AMAZING SCRUBBING POWER OF REV OUTSCRUBS. OUTPERFORMS. IT S REVOLUTIONARY. REV. There s never been another scrubber

More information

GET WIRED FOR SUCCESS WITH NEW NORTON WIRE BRUSHES

GET WIRED FOR SUCCESS WITH NEW NORTON WIRE BRUSHES GET D FOR SUCCESS WITH NEW BRUSHES When you need the perfect low-impact solution for refining surfaces without removing any base material, try our new line of Norton wire brushes. This new, economically

More information

FINISHING SYSTEMS SILICONE-FREE POLISHING & COMPOUNDING PRODUCTS

FINISHING SYSTEMS SILICONE-FREE POLISHING & COMPOUNDING PRODUCTS FINISHING SYSTEMS SILICONE-FREE POLISHING & COMPOUNDING PRODUCTS PRODUCT DESCRIPTION DRX 1000 CUTTING COMPOUND DRX 1500 POLISHING COMPOUND FINISH GLAZE A673 A674 A675 DRX 3000 PROFESSIONAL FINISH ENHANCER

More information

RESIN FIBER DISC PADS

RESIN FIBER DISC PADS RESIN FIBER DISC PADS SMOOTH FACE RFD PADS These pads are made from proprietary thermoplastic rubber compounds that provides consistent properties over a wide range of temperatures. They are ideal pads

More information

3M Automotive Aftermarket Division Masking Solutions Products Catalog/Edition 1. Critical Edge. Masking. Solutions.

3M Automotive Aftermarket Division Masking Solutions Products Catalog/Edition 1. Critical Edge. Masking. Solutions. 3M Automotive Aftermarket Division Masking Solutions Products Catalog/Edition 1 Critical Edge Masking Solutions Product Catalog Masking Applying paper and tape to a vehicle to protect it from overspray

More information

Top Side Door Door Model Work Area Height Door Options Opening Opening Gun Options Weight

Top Side Door Door Model Work Area Height Door Options Opening Opening Gun Options Weight FLOOR MODEL STEEL CABINETS 40403 40413 Standard Features for All Models 100 CFM dust collector included with all steel cabinets HD 14 gauge steel - welded seams Full width top door Optional additional

More information

3M Abrasive Systems Random Orbital Abrasive Disc Portfolio. Sanding & Finishing. Solutions. see inside. Distributed by:

3M Abrasive Systems Random Orbital Abrasive Disc Portfolio. Sanding & Finishing. Solutions. see inside. Distributed by: 3M Abrasive Systems Random Orbital Abrasive Disc Portfolio Sanding & Finishing Solutions! cs NsEivW e Dis Abra see inside Distributed by: The 3M Value The RIGHT Abrasives NEW Products NEW! Look for this

More information

3M Overhaul Service Kit

3M Overhaul Service Kit SERVICE INSTRUCTIONS FOR 3M 12,000 RPM 3 in. (77 mm) RANDOM ORBITAL SANDERS 3M Overhaul Service Kit The part number 20346, 3M Overhaul Service Kit, contains all the replacement parts that naturally wear

More information

3M Abrasive Systems. Metalworking Application Guide. Advanced Metalworking. with 3M support

3M Abrasive Systems. Metalworking Application Guide. Advanced Metalworking. with 3M support 3M Abrasive Systems Metalworking Application Guide Advanced Metalworking with 3M support 3 Product symbols MS Stainless Steel Mild Steel Aluminium Grinding Aid High Pressure Medium Pressure Alumina Zirconia

More information

Watch thevideo! dead end pressures that can result in serious or fatal injuries if blocked.

Watch thevideo! dead end pressures that can result in serious or fatal injuries if blocked. MOBILE VIEW Guns Guns use engineered air nozzles for high performance! Guns Why EXAIR Guns? Inexpensive air guns are sold through many catalogs and industrial supply companies. Most have triggers or other

More information

Industrial. Ready when you are. RediPower. Tools

Industrial. Ready when you are. RediPower. Tools RediPower Industrial Tools Ready when you are RediPower Ready when you are Available, cost effective, and durable are recognized attributes of the RediPower products. Since their introduction in the mid

More information

MT07 MT03 MHS100AG MEASURING TAPE & HACKSAW MEASURING TAPE & HACKSAW MEASURING TAPES MEASURING TAPES HEAVY DUTY DELUXE TYPE HACKSAW W/12" H.S.S.

MT07 MT03 MHS100AG MEASURING TAPE & HACKSAW MEASURING TAPE & HACKSAW MEASURING TAPES MEASURING TAPES HEAVY DUTY DELUXE TYPE HACKSAW W/12 H.S.S. MEASURING TAPE & HACKSAW MEASURING TAPE & HACKSAW MT07 ITEM NO. MT03 MEASURING TAPES HIGH IMPACT ABS CASE W/ RUBBER PROTECTED RUBBER COVERED CASE, COMFORTABLE SIZE MEASURING TAPES INNER PC/BOX PACKING

More information

POWER TOOL SOLUTIONS CALL TODAY TOLL FREE: Abrasive Tools

POWER TOOL SOLUTIONS CALL TODAY TOLL FREE: Abrasive Tools CATALOG 2018 www.eagle-group.com Abrasive Tools Impact Wrenches Drills TM POWER TOOL SOLUTIONS Eagle Group is a leading supplier of power tools for industrial markets. Whether you need tools for material

More information

MICHIGAN PNEUMATIC TOOL

MICHIGAN PNEUMATIC TOOL MICHIGAN PNEUMATIC TOOL Industrial Air Tools Grinders 2016 Serving All Industries Petro Chemical Aircraft Assembly Foundry Rental 1-800-521-8104 www.michiganpneumatic.com MATERIAL REMOVAL Right Angle Grinders

More information

Fuel Additives. Turbo 108 Fuel Injector Cleaner. Turbo 108 Octane Boost 16 oz & 32 oz.

Fuel Additives. Turbo 108 Fuel Injector Cleaner. Turbo 108 Octane Boost 16 oz & 32 oz. Fuel Additives Turbo 108 Fuel Injector Cleaner Specially formulated to provide maximum engine performance in Fuel Injected gasoline engines Unclogs dirty injectors Eliminates hard starting and poor acceleration

More information

Mighty Seven Pneumatic Air Tools and Accessories 2018 New Tools Complete Air Tool Solutions

Mighty Seven Pneumatic Air Tools and Accessories 2018 New Tools Complete Air Tool Solutions Mighty Seven Pneumatic Tools and Accessories 2018 New Tools Complete Tool Solutions NC 4612B 1/2 Dr. Impact Wrench Square Drive Bolt Capacity Max. Torque Pressure Net Weight Hose Overall Length 1/2 5/8

More information

OEM APPROVED AND USED

OEM APPROVED AND USED OEM APPROVED AND USED Pro Form's Pliogrip Truck Line epoxy and urethane adhesives are part of a complete system designed for the most demanding bonding applications in the truck refinish industry. www.proformproducts.com

More information

FR11A Fender, Welded-On

FR11A Fender, Welded-On Uniform Procedures For Collision Repair FR11A Fender, Welded-On 1. Description This procedure describes the repair and complete replacement of a welded-on aluminum fender. Inspection and evaluation requirements

More information

SIOUX TOOLS FORCE PRODUCT CATALOG ABRASIVE

SIOUX TOOLS FORCE PRODUCT CATALOG ABRASIVE SIOUX TOOLS FORCE PRODUCT CATALOG ABRASIVE Abrasive Index Straight Die Grinders......................... 25 Right Angle Die Grinders...................... 26 23 SIOUX TOOLS FORCE PRODUCT CATALOG Make Easy

More information

FIND THE MOST CURRENT OFFERING OF SUPPORT DOCUMENTS AND WARNING

FIND THE MOST CURRENT OFFERING OF SUPPORT DOCUMENTS AND   WARNING Dynorbital Supreme Parts Page Reorder No. PD12 32 Effective November, 2012 Supersedes PD09 03 For Serial No. 12K1000B and Higher 12,000 RPM Air Powered Random Orbital Sander Air Tool Manual Safety, Operation

More information

AIR DRILL, AIR ANGLE GRINDER and AIR DIE GRINDER

AIR DRILL, AIR ANGLE GRINDER and AIR DIE GRINDER AIR DRILL, AIR ANGLE GRINDER and AIR DIE GRINDER AIR DRILL KW0800256 3/8 Chuck, Reverse Equipped with precision chucks for excellent accuracy Precision bearing provides longer tool durability KW0800258

More information

HOW - TO SCRATCH & DENT REPAIRS

HOW - TO SCRATCH & DENT REPAIRS HOW - TO SCRATCH & DENT REPAIRS Tool And Material Checklist Wax and Grease Remover Sandpaper Assortment and Sanding Block Tack Cloth and Lint-free Cloths Glazing Putty Rubber Contour Squeegee Body Filler

More information

PAGE NO. GRINDERS & CUT-OFF TOOLS PAGE NO. 3/8 IMPACT WRENCHES MODEL NO. DESCRIPTION

PAGE NO. GRINDERS & CUT-OFF TOOLS PAGE NO. 3/8 IMPACT WRENCHES MODEL NO. DESCRIPTION The AIRCAT line represents the most significant advances in the performance of pneumatic power tools in nearly 30 years. Founded in 1998, our tool line has a substantially reduced level of noise while

More information

AIR TOOLS & ACCESSORIES AIR TOOLS & ACCESSORIES HI-FLO COUPLERS AIR TOOLS & ACCESSORIES ACCESSORIES. Hi-Flo & Couplers

AIR TOOLS & ACCESSORIES AIR TOOLS & ACCESSORIES HI-FLO COUPLERS AIR TOOLS & ACCESSORIES ACCESSORIES. Hi-Flo & Couplers HI-FLO Increased airflow to provide maximum torque and optimal performance Push-To-Connect for easy connect/disconnect Includes (1) Male Coupler, (2) Female Couplers, (3) Female Plugs, and (4) Male Plugs

More information

Installation Instructions For: Suzuki Samurai, All Years Part Number: TM

Installation Instructions For: Suzuki Samurai, All Years Part Number: TM Installation Instructions For: Suzuki Samurai, All Years Part Number: 51761 TM Patent Pending WARNING This product is designed to enhance the appearance of the vehicle and to shield the occupants from

More information

RF81 Finish Defects. Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0

RF81 Finish Defects. Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0 Uniform Procedures For Collision Repair UPCR RF81 Finish Defects Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0 1. Description This procedure describes methods for correcting finish

More information