PDTR Wingless Super Modified Rules for In 2015 Transponders will be mandatory on all cars (mounting location to be determined)

Size: px
Start display at page:

Download "PDTR Wingless Super Modified Rules for In 2015 Transponders will be mandatory on all cars (mounting location to be determined)"

Transcription

1 PDTR Wingless Super Modified Rules for 2015 In 2015 Transponders will be mandatory on all cars (mounting location to be determined) To start the 2015 season any engine will be allowed, any fuel. We may add weight and a harder tire for larger engines to equalize for 360 engine. After the division has been established an engine rule will be written. 1. Steel Frames A. Fabricated steel frames must meet these specifications: Thickness to be no less than.120 inch; Frame rail width must be two (2) inches; Frame rail height must be no less than four (4) inches and 2X4X.120 inch TUBE STEEL ONLY. Frame rails may be tapered from front roll cage upright to no less than two and one quarter (2-1/4) inches. Length frame rail must begin no more than nine (9) inches behind center line of front axle, and must be continuous to the rear of the fuel tank. ALL FRAMES MUST BE APPROVED BY PDTR. B. Minimum width of the frame inside must be no less than twenty-six (26) inches between the frame rails. This measurement will be taken at the front vertical upright of the roll cage and continue all the way to the rear of the frame. This rule also applies to the lower rails of the chassis and must remain twenty-six (26) inches minimum width inside throughout the entire driver s compartment. C. No round tubular frames of any manner, shape or form will be allowed. D. Minimum wheel base allowed will be ninety (90) inches measured from wheel center to wheel center on both sides. 2. Steel Roll Cages A. Roll cages must have a six point mount with rear roll support mounted within eight (8) inches of the top of the roll cage and run rearward to main frame rail. Front roll cage upright may be extended below belt line with square tubing. All roll cage tubing must measure no less than one and three-quarter (1-3/4) inches O.D. and.095 inch wall thickness. All right angles must be gusseted and properly welded. B. All roll cages must measure no less than twenty-six (26) inches inside at the top rear and no less than twenty-three (23) inches inside at the top front. C. Minimum side protection on both sides between bottom of window opening and floor or lower chassis rail must be two (2) vertical bars, equally spaced and two (2) horizontal bars equally spaced. Side protection bars are to be a minimum one and one-half (1-1/2) inches O.D. and.095 wall thickness. D. Top and rear roll bars and bracing behind seat must be adequately padded in all areas where the driver s head may contact. E. Roll cage must extend above driver s helmet by a minimum of two (2) inches DIRECTLY ABOVE THE DRIVER S NORMAL SEATED POSITION MEASURED FROM SIDE TO SIDE. More clearance is recommended. No roll cage extensions are allowed. If there is not two (2) inches clearance above driver s head, car will not be allowed on track. Any additional bars or hoops above or around driver must be approved by PDTR. F. Side window opening height must be no less than seventeen (17) inches and no more than twenty-four (24) inches, measured from the bottom of the top roll cage bar to the top of the top horizontal side bar. 3. Driver s Compartment A. High back aluminum or better seat is mandatory. Seat must be securely bolted in a minimum of four (4) places; 2 in the bottom and 2 in the back of the seat with ¼ inch minimum diameter grade 8 bolts. NO DZUS FASTENERS ALLOWED. B. All cars must have protective plating securely fastened to protect the rear half of the bottom of the seat and the lower portion of the vertical back of the seat. Plating can be no less than one-eighth (1/8) inch thick steel

2 or one-quarter (1/4) inch thick aluminum. C. Steering wheels must be quick-release type. No plastic quick releases allowed. D. Steering gear box and tubes must be adequately padded to protect driver s knees. E. All cars must have a complete firewall between the driver and the engine and a firewall between driver and fuel tank. Rear firewall must extend to bottom of the fuel tank. All cars must have complete floor boards or adequate length to protect driver s feet. All sheet metal must be no less than 22 gauge steel or.050 inch aluminum. F. No rear view mirrors of any kind are allowed. G. Ignition switch must be mounted on the right side of the dash within reaching distance of the driver when securely strapped in, and clearly marked. H. Toe strap on top of accelerator pedal is mandatory 4. Bodies and Hoods A. Bodies must be identifiable to automobile manufactured bodies. Suggest using replica or original tail-lights. You may run topless or open top cars. If you run a roof NO WICKERBILL! PITCH FROM FRONT TO REAR of roof NO MORE THAN 2in.! B. Sprint type cars, midget, etc. do not maintain a stock car appearance and will not be allowed. C. No late model full bodied stock cars will be allowed to run as a modified. D. All cars must have a hood that extends over the top of the radiator. Hoods must be straight front to rear, and may be rounded right to left. Cowls and mud deflectors may be part of the hood. No holes are allowed in top of hood. All cars must have a 360 degree steel fan guard. E. Stainless steel screening is compulsory in windshield 2X2X3/16. Left and right windows must have protective screen to deflect stone, etc. No glass of any kind permitted. F. Numbers must be on both sides of the car and roof if used. 5. Mirrors No rear view mirror will be allowed. 6. Engines A. Any American made V-8 cast iron block production engine 360 OR smaller may be used. Stock type aftermarket replacement blocks may be used. No aluminum block or heads allowed. No Oldsmobile Rocket blocks allowed. Ignition must be camshaft driven. No more than one (1) spark plug per cylinder and no more than two (2) valves per cylinder will be allowed. Any engine not listed must be approved by PDTR. No titanium parts allowed anywhere on car except in valve train. B. * Intake one piece, aluminum or cast iron. No high rise tunnel ram. Unaltered carburetor, fuel pump mechanical stock type diaphragm only, no piston pumps. Carburetor heat spacer allowed, a maximum of 1/2 inch thick. Only one (1) air cleaner is allowed, 14 round and 4 tall. No stack extensions on top of carburetor. If running engine bigger than 360 with fuel injection, we may add weight, harder tire, or increase tire pressure to make the car competitive to a 360 engine. C. Stock HEI Ignition ONLY!! NO MAGINETOS NO MSD BOXES!!! D. All cars will use an adequate radiator overflow tank of at least one (1) quart capacity. It is not allowed to be mounted in the driver s compartment. Overflow may be run through exhaust header as long as no water problems exist. E. No dry sump oil systems will be allowed.

3 F. Exhaust must exit in front of rear tires, and below top horizontal side bar. Mufflers and elbows must be welded on entirely approved by PDTR. Cars will be routinely checked with a decimeter and those louder than 100 decibels will be required to modify their systems to lower the level of noise emissions. Muffler systems cannot be changed after decibel reading is taken. Headers 1 5/8 in. OD, no merge collector. One collector per side. No tri Y Header collectors. No slip connectors. Mufflers part # Schonfield ONLY!!! G. Engine Placement The position of the engine is up to the discretion of the car builder, except; No rear engine or mid-engine cars will be allowed. Engine must be mounted between frame rails and driver must sit behind engine. H. Traction control devices of any kind are illegal. I. NO super chargers, turbo chargers, nitrous oxide, or timed injection will be allowed. 7. Flywheels and Bell Housings A. Any type flywheel may be used and the car must be equipped to be self-starting. All cars must be equipped with one working clutch. The car must have a neutral gear. Steel or aluminum drive flanges may be used. B. All cars must have a BLOW PROOF bell housing. 8. Transmissions A. All cars must be equipped with a self-starting, self-propelled type transmission. Must be able to move under own power to get car moving. One forward gear and one neutral gear in transmission mandatory. Driver must be able to shift gears while securely strapped in car. No shifter rear ends or shifter drive lines. No quick change auxiliary or automatic transmissions allowed. Transmission must be bolted to back of bell housing and must be mounted to outside of bell housing. Dog type clutches can be run. B. All cars running an open drive shaft must have a complete loop of one-quarter (1/4) inch thick by one (1) inch wide steel attached to the frame to support the support the front end of the drive shaft. An adequate safety chain, strap or other device must support torque arms. Driver s compartment must be shielded from open drive shafts. C. All open drive shafts must be painted white. 9. Front Axle, Spindles, Hubs and Shocks A. Only steel front axles, king pins and spindles with standard length ¾ ton (Wide 5) spindle snouts will be allowed. Only standard Wide 5 hubs allowed. No billet hubs allowed. Hubs must be interchangeable on all four spindles. The right front hub does not need brake rotor mounts. B. Welded steel shocks only with removable bearing or rubber ends, No shocks that are adjustable from the driver s compartment allowed. No mono-tube shocks allowed. No aluminum shocks allowed, No take apart shocks. Coil over steel shocks allowed. No Bilstein XVS series shocks allowed. ALL SCHOCKS MUST BE Approved By PDTR 10. Differentials 11. Brakes A. No restrictions as to manufacturer. Quick change rear ends are allowed. Any car running a passenger car rear end must have conventional full-floating hubs. No open tube rear or aluminum axle tubes are allowed. A. All cars must have a minimum of three (3) wheel hydraulic brakes, one on each rear wheel. All in good working condition. B. Steel brake rotors only; no aluminum or composite rotors or coated are allowed.

4 C. Cars are allowed to run proportioning valves. 12. Fuel and Fuel Tanks A. Fuel tank must be mounted equal to or higher than the height of the top of the rear axle tubes, in the truck area of the car. No nylon straps allowed. B. Fuel cell only enclosed in a steel container, mounted in a safe manner approved by PDTR. [ See Speedway Motors fuel cells or equitant] C. If fuel line is run inside driver s compartment, it must be steel braided line, Aeroquip push lock line or a line of equivalent structure, or it must be contained inside steel tubing. D. Anti-surge fuel filler caps are mandatory. E. No form of pressurized fuel system will be allowed. F. All cars must have an easily accessible ball valve shutoff mounted inside frame rails at right rear of car G. The accelerator linkage must be equipped with two return springs in the linkage. H. Cable type accelerator linkage will be allowed if approved by PDTR. 13. Bumpers and Nerf Bars A. Front bumpers must not extend beyond frame rails. All corners and edges must be rounded. Main bumper structure must be one and one-half (1-1/2) inch diameter round tubing. Standards and cross bars must be at least one (1) inch round tubing. All standards must be properly braced. Standards must be connected by a horizontal cross bar parallel to the main bumper hoop. Front bumper must not extend more than twelve (12) inches beyond the leading edge of the front tires. Single hoop front bumpers will be allowed, but must be between fifteen (15) and twenty-one (21) inches from the ground. B. Rear bumper minimum width must be equal to outside width of frame rails, and maximum width no greater than rear tire tread width. Main bumper structure must be of one and one-half (1-1/2) inch minimum diameter round tubing. Maximum distance from the ground to the bottom of the rear bumper or standards cannot exceed fifteen (15) inches. Minimum distance from the ground to the top of the rear bumper or standards can be no less than twenty-one (21) inches. All vertical standards must be connected by horizontal cross bars no smaller than one (1) inch diameter round tubing. All standards must be properly braced. Rear bumper must have at least three (3) vertical standards with one in center line of frame. Outside corners and edges must be rounded. When bumper extends beyond the width of the frame rails, it must be looped back 180 degrees to the frame. C. Nerf bars must not extend beyond outside of tires. Materials for nerf bars will be no less than one (1) inch diameter round tubing, and rounded on the edges and corners. D. All bumpers and nerf bars must be built of round tubing and painted or plated in a bright color. 14. Wheels and Tires A. Steel wheels only, fourteen (14) inches wide maximum, plus bead lock. Must be painted or plated a bright color. B. Tire pressure bleed-offs will not be allowed. C. * Approved right rear tire for the racing season will be American Racer 33.0/ GT SD44 compound for cars that meet the engine rule. All other cars, American Racer 33.0/13.0-GT15 MD62 with adjusted tire pressure. This tire must measure 14 or less, from Point A to B, as illustrated below. The measurement will be taken on a 14 wheel with bead lock and the tire pressure set at 12 psi. The tire must also have a durometer reading of 28, or harder with a surface temperature of 150 degrees. Any tire that does not meet the guidelines in this section will not be legal regardless of the sidewall stamping.

5 D. Foam plugs, Aluminum or Lexan wheel covers safely attached approved by PDTR 15. Batteries A. All batteries must be safely and securely fastened between frame rails and between front and rear torsion bar tubes (or the equivalent on coil spring cars). Batteries must be protected from the driveshaft or other flying debris with 1/8 inch aluminum or 1/6 inch steel if mounted in the driver s compartment; subject to the approval of PDTR. Standard acid type batteries must have the positive post and entire top covered to prevent acid spillage in the event of a roll over. Gel or dry cell type batteries must have the positive post covered. 16. Weight of Cars A. Minimum weight 2,150 cars that meet engine rule. All other cars weight will be adjusted according to engine size. Cars will be weighted directly from the track, without pitting. Any parts lost during a race may be used for weighing the car, with the exception of fluids and weights. B. All weights must be painted white, identified with the car number, and securely fastened, subject to the approval PDTR. C. Loss of any weight on the track will result in a ten (10) point and money penalty. D. Weight will be established with PDTR Scales 17. Driver s Safety A. See Track Rules. 18. Drives Must Be 16 Years Old 19. *TRANSPONDER LOCATION Transponder will mounted on the left side rear tortion tubes.

PDTR Open Wheel Modified Rules Tenative For 2014

PDTR Open Wheel Modified Rules Tenative For 2014 PDTR Open Wheel Modified Rules Tenative For 2014 Steel Frames Fabricated steel frames must meet these specifications: Thickness to be no less than.120 inch; Frame rail width must be two (2) inches; Frame

More information

1. American made automobile steel, aluminum or rubber glass bodies are allowed as long as they follow original body lines.

1. American made automobile steel, aluminum or rubber glass bodies are allowed as long as they follow original body lines. Modified Style Bodies MAHONING VALLEY SPEEDWAY 2014 MODIFIED RULES Revised 12-2-13 ALL CARS MEETING THESE RULES & SPECIFICATIONS WILL BE ELIGIBLE TO RACE Any touring car motor is legal except big blocks.

More information

2019 Super Street Class Rules. All drivers are required to have their own Raceivers for one-way communication with race director official.

2019 Super Street Class Rules. All drivers are required to have their own Raceivers for one-way communication with race director official. 2019 Super Street Class Rules All drivers are required to have their own Raceivers for one-way communication with race director official. Top 3 feature finishers will be required to go to tech area after

More information

Econo-Mod Rules. *Transponders & Raceceivers mandatory*

Econo-Mod Rules. *Transponders & Raceceivers mandatory* Econo-Mod Rules Top 3 from each heat must scale. Top 5 from each feature must scale & go immediately to tech. Failure to do so will result in a disqualification. *Transponders & Raceceivers mandatory*

More information

Section 10 Mini Stocks

Section 10 Mini Stocks Section 10 Mini Stocks 10.1 DEFINITION. 10.1.1 The word stock will mean unaltered as originally factory produced and installed for make. All Cars and trucks will be stock unless otherwise specified within

More information

SANDIA SPEEDWAY 2018 STREET STOCK DIVISION RULES

SANDIA SPEEDWAY 2018 STREET STOCK DIVISION RULES SANDIA SPEEDWAY 2018 STREET STOCK DIVISION RULES DRIVER: The minimum age for a driver is fourteen (14), unless approved by two of the following three: race director, tech inspector or promoter. All required

More information

2015 Super Stock verses Street Stock. Rules UPATES 2/12/2015

2015 Super Stock verses Street Stock. Rules UPATES 2/12/2015 2015 Super Stock verses Street Stock Rules UPATES 2/12/2015 1. All racecars must display Super Stock or Street Stock at which it will compete on left side windshield post. Must be two (2) inches tall.

More information

All drivers must have working race radios in order to compete. Scoring Transponder is optional for 2015 but will be mandatory for 2016

All drivers must have working race radios in order to compete. Scoring Transponder is optional for 2015 but will be mandatory for 2016 Brockville Ontario Speedway 2016 BOS STREET STOCK RULES All drivers must have working race radios in order to compete. Scoring Transponder is optional for 2015 but will be mandatory for 2016 CAR ELIGIBILITY

More information

SUPER 4-CYLINDER RULES MODELS

SUPER 4-CYLINDER RULES MODELS SOUTHERN OREGON SPEEDWAY 2177 South Pacific Highway Medford, OR 97501 541-282-8066 / 1-800-963-3367 Fax: 541-774-3627 / Website: www.sospeedway.com SUPER 4-CYLINDER RULES 2009 1. MODELS A. Any front engine,

More information

1- Any stock appearing metal bodied four cylinder car or truck through the current year.

1- Any stock appearing metal bodied four cylinder car or truck through the current year. Super Stock 4 2018 Rules 1- Any stock appearing metal bodied four cylinder car or truck --1965 through the current year. 2- You may run an aftermarket fabricated body. The body must be made from magnetic

More information

PURE MINI STOCK CLAIMERS 2008

PURE MINI STOCK CLAIMERS 2008 SOUTHERN OREGON SPEEDWAY 113 Haskell St., Central Point, OR 97502 541 261 7077 Fax: 541 664 6657 Website: www.sospeedway.com PURE MINI STOCK CLAIMERS 2008 1. MODELS: A. Any front engine, front or rear

More information

CYLINDER TRUCK RULES

CYLINDER TRUCK RULES 2019 4 CYLINDER TRUCK RULES The rules herein shall refer to Adirondack International Speedway as AIS. These rules are intended to create affordable and fair competition. While they offer a good outline,

More information

ELIGIBLE MODELS Chevy C-10 GMC 1500 Dodge Ram Ford F-150

ELIGIBLE MODELS Chevy C-10 GMC 1500 Dodge Ram Ford F-150 2018 SUPER TRUCKS RULES $1000 fine for tire soaking $100 fine for antifreeze ELIGIBLE MODELS Chevy C-10 GMC 1500 Dodge Ram Ford F-150 HMS Enforcer (Harrington Spec) 2850/1265 lbs with driver 1. Minimum

More information

Claremont Speedway 2015 Wildcat rules

Claremont Speedway 2015 Wildcat rules Claremont Speedway 2015 Wildcat rules These rules are to be used as a guide The wildcat division is a division that is for the racer that wants to have fun with a limited amount of knowledge and at an

More information

Pure Stock Specifications

Pure Stock Specifications 15112 National Pike, Hagerstown, MD 21740 PHONE (301) 582-0640 FAX (301) 582-3618 info@hagerstownspeedway.com Pure Stock Specifications ENGINES A.) Solid lifter cams allowed. No rollers B.) Roller Rockers

More information

2018 Mini Sport Rules

2018 Mini Sport Rules 2018 Mini Sport Rules Mini Sport 2018 revised 12/21/2016 1. ELIGIBILITY A. Front engine, compact cars and short wheel base mini trucks with conventional cabs. B. NO Convertables, Station Wagons, supercabs,

More information

U-CAR Rules GLASS: All glass & lexan removed. Screen or 4 bars or both in front of driver. 5. WEIGHT: Must weigh 2450lbs

U-CAR Rules GLASS: All glass & lexan removed. Screen or 4 bars or both in front of driver. 5. WEIGHT: Must weigh 2450lbs U-CAR Rules 2018 1. COMPETING MODELS: 1980 or newer 4 cylinder front wheel drive 4 passenger 2 or 4 door sedans are allowed. No rear wheel drive vehicles allowed. 2. GENERAL BODY: Wheelbase must remain

More information

Larry King Law Langley Speedway 2018 Modified Division Rules

Larry King Law Langley Speedway 2018 Modified Division Rules Larry King Law Langley Speedway 2018 Modified Division Rules Amendments: Rules are subject to amendments at any time when ample notice has been given to enhance competition 1. ROLL CAGES A. Roll bars must

More information

2019 Pure Thunder Stock Class Rules. All drivers are required to have their own Raceivers for one-way communication with race director official.

2019 Pure Thunder Stock Class Rules. All drivers are required to have their own Raceivers for one-way communication with race director official. 2019 Pure Thunder Stock Class Rules All drivers are required to have their own Raceivers for one-way communication with race director official. Top 5 feature finishers will be required to go to tech area

More information

Legion Speedway All American Truck Pulling Series Rules

Legion Speedway All American Truck Pulling Series Rules Legion Speedway All American Truck Pulling Series Rules 10,000 lb. OPEN CLASS All General Safety Rules Apply Gas, diesel and racing fuel only no alcohol, nitrous, propane, etc. 500 cu. in. maximum Maximum

More information

GRAND AMERICAN MODIFIED RULES

GRAND AMERICAN MODIFIED RULES GRAND AMERICAN MODIFIED RULES *** Please refer to General Section for rules and regulations applicable to all divisions*** CNS Reserves the right to alter or amend the Rules and Regulations in the interest

More information

CHARGER 2017 RULES & REGULATIONS Revised 1/22/17

CHARGER 2017 RULES & REGULATIONS Revised 1/22/17 CHARGER 2017 RULES & REGULATIONS Revised 1/22/17 IMPORTANT NOTE: Applications for NASCAR License may be obtained from the Pit Steward at the sign -in-window or at the speedway office during regular business

More information

LANCO MICRO MIDGET AUTO RACING CLUB, INC Car Specifications

LANCO MICRO MIDGET AUTO RACING CLUB, INC Car Specifications Date: 11/16/2017 These specifications provide the framework for LMMC officials to inspect racecar. In addition to interpreting and enforcing these specifications, LMMC officials are authorized to make

More information

DRIVER ELIGIBILITY GUIDELINES TO RACE CLASSES

DRIVER ELIGIBILITY GUIDELINES TO RACE CLASSES SPORTSMAN RULES DRIVER ELIGIBILITY GUIDELINES TO RACE CLASSES Any DRIVER that has won a CRATE / Limited/ Super Late Model Feature event at Boyd's Speedway in 2017 cannot register to race in any class lower

More information

2017 Northeast Wingless Sprint Rules

2017 Northeast Wingless Sprint Rules 2017 Northeast Wingless Sprint Rules If your question is not in these rules, do not assume it is legal. Ask first! This class Northeast Wingless Sprint Cars is intended to offer an affordable sprint car

More information

PROSTOCK CLASS. Infraction of rules will be decided by Race Officials. Number Plate

PROSTOCK CLASS. Infraction of rules will be decided by Race Officials. Number Plate PROSTOCK CLASS Tech Rules: Must have race receiver and needs to work (cruiser class: both driver & passenger must be able to hear) All four brakes must lock up or won t race. You will load up and go home

More information

Section 9 Street Stocks

Section 9 Street Stocks Section 9 Street Stocks 9.1.1 DEFINITION 9.1.1 The word stock will mean unaltered as originally factory produced and installed for make (GM to GM) (Mopar to Mopar). All cars and trucks will be stock unless

More information

Engine option #1 Nesmith sealed 602 with 4412 Holley 500 cfm two barrel. 1" spacer.030 tolerance. Street Stock Rules

Engine option #1 Nesmith sealed 602 with 4412 Holley 500 cfm two barrel. 1 spacer.030 tolerance. Street Stock Rules Hobby Street Stock Rules (Updated 1/1/2019) 1. All 3300 lbs 2. Remote starter button track supplied at inspection 3. No high performance parts allowed except as stated. 4. Wheel base 108. min. 5. Stock

More information

2012 Street Stock Rules

2012 Street Stock Rules Rules & Regulations Updated 11/26/11 CHASSIS: 1. Cars must be 1960 or newer, stock passenger type cars. 2. No Commercial vehicles, convertibles, sports cars or Novas allowed. No leaf spring cars. 3. Frame

More information

Southern Oregon Speedway 2011 Modified Rules

Southern Oregon Speedway 2011 Modified Rules Southern Oregon Speedway 2011 Modified Rules TO ALL COMPETITORS/PARTICIPANTS 15.0 Modifieds ANY CAR, TEAM AND/OR DRIVER THAT DOES NOT MEET THESE SPECIFICATIONS AND/OR EQUIPMENT REQUIREMENTS WILL BE SUBJECT

More information

ARIZONA SUPER STOCK Super Stock Rules and Regulations

ARIZONA SUPER STOCK Super Stock Rules and Regulations ARIZONA SUPER STOCK 2014 Super Stock Rules and Regulations If the rules don t say you can, assume you cannot. The rules are written as a guideline. If you are unsure about something, ask an official. The

More information

P.O. Box 9 Conowingo, MD Phone:

P.O. Box 9 Conowingo, MD Phone: Street Gas: *6800lbs. Maximum weight. 1. Ballast is permitted. Ballast may be added. Added weight must be secured within the body of the truck. No weights allowed in the cab. No front weights or weight

More information

2018 Roadrunner Rules

2018 Roadrunner Rules 2018 Roadrunner Rules BIG DIAMOND SPEEDWAY 2018 ROADRUNNER RULES The purpose of this division is to create a controlled, economical, competitive form of racing. The primary concern is to keep the cars

More information

Wayne County Speedway Super Stock Rules Updated November 20 th 2017

Wayne County Speedway Super Stock Rules Updated November 20 th 2017 Wayne County Speedway Super Stock Rules Updated November 20 th 2017 Bodies Any American manufactured, steel bodied, production passenger car or small truck (S10, Ranger, Dakota). No full size trucks. No

More information

SOUTHERN OREGON SPEEDWAY 2177 SOUTH PACIFIC HWY MEDFORD, OREGON (541) / DWARF LITE RULES 2009

SOUTHERN OREGON SPEEDWAY 2177 SOUTH PACIFIC HWY MEDFORD, OREGON (541) / DWARF LITE RULES 2009 SOUTHERN OREGON SPEEDWAY 2177 SOUTH PACIFIC HWY MEDFORD, OREGON 97501 (541) 282-8066 / 1-800-963-3367 www.sospeedway.com DWARF LITE RULES 2009 Any car specifications not covered in these rules are subject

More information

ENDURO Division 2016 RULES AND REGULATIONS

ENDURO Division 2016 RULES AND REGULATIONS ENDURO Division 2016 RULES AND REGULATIONS 1. ELIGIBLE VEHICLES: Open to any make of front wheel drive (FWD) car with two or four doors. All wheel drive cars (AWD) will be allowed but driveshaft must be

More information

2013 OPEN WHEEL MODIFIED RULES

2013 OPEN WHEEL MODIFIED RULES 2013 OPEN WHEEL MODIFIED RULES BODY: 1970 or newer American passenger cars only. No panel vans or station wagons. Stock appearing front window support units must be used. A minimum window opening of twelve

More information

Colorado National Speedway Rules: Pure Stocks Last Revised: February 1, 2018

Colorado National Speedway Rules: Pure Stocks Last Revised: February 1, 2018 PURE STOCK RULES *** Please refer to General Section for rules and regulations applicable to all divisions*** DRIVER ELIGIBILITY: This is an entry level race division. You (The Driver) must be at an entry

More information

M.O.R.R. MOD KART RULES (EDITED APRIL 26, 2018)

M.O.R.R. MOD KART RULES (EDITED APRIL 26, 2018) M.O.R.R. MOD KART RULES - 2018 (EDITED APRIL 26, 2018) MOD KART CLASS: This class is represented by a 4-wheel race vehicle powered by a 400cc Honda Quad engine. It is designated for drivers ages 11-16

More information

I-96 Speedway Cylinder Rules

I-96 Speedway Cylinder Rules I-96 Speedway 2019-4 Cylinder Rules Personal Protection Equipment It is the sole responsibility of each competitor for the effectiveness and proper installation, per the manufacturers specifications to

More information

Wingless Limited Sprint Rules CHASSIS

Wingless Limited Sprint Rules CHASSIS Wingless Limited Sprint Rules CHASSIS 1. Any type of sprint car chassis is allowed that has a minimum of 84 inches and a maximum 90 inches, measured from center of the front hub to the center of the rear

More information

2017 UPDATE 3/6/17 Thunder Car Rules

2017 UPDATE 3/6/17 Thunder Car Rules Mt. Lawn Speedway 2017 UPDATE 3/6/17 Thunder Car Rules The absence of a particular rule does NOT necessarily mean its approval! FRAME 1. Any 1968 and newer, full frame, rear wheel drive full sized car,

More information

LIMITED LATE MODEL RULES

LIMITED LATE MODEL RULES LIMITED LATE MODEL RULES A. Any steel block ENGINE B. Any piston allowed C. Any steel crank (no titanium) D. Balancing permitted E. Polishing rods allowed F. Any steel rod (no titanium) G. Dry sump oil

More information

Section 9 ½ Claimer Stocks

Section 9 ½ Claimer Stocks Section 9 ½ Claimer Stocks 9 ½.1.1 DEFINITION 9 ½.1.1 The word stock will mean unaltered as originally factory produced and installed for make (GM to GM) (Mopar to Mopar). All cars and trucks will be stock

More information

2018 Vintage Car Rules

2018 Vintage Car Rules 2018 Vintage Car Rules Minimum age of Legends drivers shall be 13. All drivers under the age of 18 must have a copy of birth certificate or driver s license and signed waiver by both parents before racing.

More information

MAHONING VALLEY SPEEDWAY 2019 LATE MODEL RULES ALL CARS MEETING THESE RULES & SPECIFICATIONS WILL BE ELIGIBLE TO RACE

MAHONING VALLEY SPEEDWAY 2019 LATE MODEL RULES ALL CARS MEETING THESE RULES & SPECIFICATIONS WILL BE ELIGIBLE TO RACE MAHONING VALLEY SPEEDWAY 2019 LATE MODEL RULES ALL CARS MEETING THESE RULES & SPECIFICATIONS WILL BE ELIGIBLE TO RACE These rules are intended to be a guideline in constructing a car. If the rules do not

More information

I-96 Speedway Street Stock Rules

I-96 Speedway Street Stock Rules I-96 Speedway 2019 Street Stock Rules Personal Protection Equipment It is the sole responsibility of each competitor for the effectiveness and proper installation, per the manufacturers specifications

More information

dog hollow speedway official 2017 pure/hobby/strictly stock rules

dog hollow speedway official 2017 pure/hobby/strictly stock rules dog hollow speedway official 2017 pure/hobby/strictly stock rules 1. GENERAL This division is open to any North American made passenger car from 1965 through the present. The make and model must be factory

More information

2018 ECONO MOD RULES

2018 ECONO MOD RULES P.O. Box 159 Track (330) 772-5481 Hartford, OH 44424 Fax (330) 772-7704 2018 ECONO MOD RULES 1. ROLL CAGE: Roll cage must consist of continuous hoops not less than 1.500 outside diameter. Must be mounted

More information

2013 Senoia Raceway Rulebook

2013 Senoia Raceway Rulebook 2013 Senoia Raceway Rulebook E-mail tech questions to: johnnywalls31@yahoo.com BOMBER RULES BODY 1. All bodies must be stock steel bodies. No fiberglass or aluminum body panels allowed. Fenders and quarter

More information

2019 STOCK 8 ENDURO RULES

2019 STOCK 8 ENDURO RULES 2019 STOCK 8 ENDURO RULES INDEX Battery Body & Exterior Eligible Cars Engine Exhaust Fuel System Interior & Drivers Compartment Personal Equiptment Radiator Suspension Tires Transmission Page 2 ELIGIBLE

More information

2017 Sportmod (B Mod) Rules

2017 Sportmod (B Mod) Rules 2017 Sportmod (B Mod) Rules FRAMES 1. 1964 or newer OEM perimeter American rear-wheeled passenger car frame only. No sports car frame. No convertible or station wagon. No stub cars 2. Frame must be full

More information

2018 SEASON PURE STOCK DIVISION

2018 SEASON PURE STOCK DIVISION 1188 James D. Hagood Hwy. P.O. Box 1066 South Boston, VA 24592 Office: 434-572-4947 Fax: 434-575-8992 Email: info@southbostonspeedway.com www.southbostonspeedway.com 2018 SEASON PURE STOCK DIVISION See

More information

2012 Roadrunner Rules

2012 Roadrunner Rules 2012 Roadrunner Rules Areas highlighted in red are changes for 2012 Revised 4-8-12 The purpose of this division was to create a controlled economical, competitive form of entry-level racing. The primary

More information

2018 CHARGER DIVISION RULES

2018 CHARGER DIVISION RULES ! 2018 CHARGER DIVISION RULES Jennerstown Speedway (Intersections of Rt. 30 & Rt. 985) PO Box 270 206 Somerset Street Jennerstown, PA 15547-0099 Track Phone: 814.703.8009 Fax: 814.703.8163 For Track Promoter

More information

Baer Field Bombers 2017 The purpose of this class division is to provide an inexpensive way for a beginner to get into full size stock car racing.

Baer Field Bombers 2017 The purpose of this class division is to provide an inexpensive way for a beginner to get into full size stock car racing. Baer Field Bombers 2017 The purpose of this class division is to provide an inexpensive way for a beginner to get into full size stock car racing. 1) All cars must be strictly stock for make and model

More information

ENDURO 4-6 Cyl Division 2015 RULES AND REGULATIONS

ENDURO 4-6 Cyl Division 2015 RULES AND REGULATIONS ENDURO 4-6 Cyl Division 2015 RULES AND REGULATIONS 2. ENDURO 4-6 Cylinder Front Wheel Drive (FWD) BUILDING RULES 1. Open to any make of 4 or 6 cylinder front wheel drive (FWD) car with two or four doors

More information

2012 Pro Stock Rules

2012 Pro Stock Rules 2012 Pro Stock Rules Areas highlighted in red are changes for 2012 Revised 5-5-2012 PRO STOCK: Any North American made car 1968 to present. This division was created as a controlled, economical and competitive

More information

Crate Motor/Limited Late Model Rules/2019

Crate Motor/Limited Late Model Rules/2019 Crate Motor/Limited Late Model Rules/2019 MUFFLERS ARE MANDATORY/RACECEIVERS MANDATORY The rules and/or regulations set forth herein are designed to provide for the orderly conduct of racing events and

More information

2019 MINI STOCK RULES

2019 MINI STOCK RULES 2019 MINI STOCK RULES INDEX Battery Body & Exterior Eligible Cars Engine Exhaust Fuel System Interior & Drivers Compartment Personal Equiptment Radiator Roll Cage Roll Cage Illustrations Suspension Tires

More information

PLEASE BE SURE YOU HAVE READ AND UNDERSTAND THE GENERAL RULES,SAFETY RULES AND DRIVER SAFETY EQUIPMENT BEFORE CONTINUING.

PLEASE BE SURE YOU HAVE READ AND UNDERSTAND THE GENERAL RULES,SAFETY RULES AND DRIVER SAFETY EQUIPMENT BEFORE CONTINUING. 2017 MOD MINI RULES Changes for 2017 are highlighted in red *Speedway Officials shall be empowered to permit minor deviations from any of the specifications herein or impose any further restrictions that

More information

PLEASE BE SURE YOU HAVE READ AND UNDERSTAND THE GENERAL RULES, SAFETY RULES AND DRIVER SAFETY EQUIPMENT BEFORE CONTINUING.

PLEASE BE SURE YOU HAVE READ AND UNDERSTAND THE GENERAL RULES, SAFETY RULES AND DRIVER SAFETY EQUIPMENT BEFORE CONTINUING. 2017 SPORTSMAN RULES Any rule changes made in 2017 are highlighted in RED. *Speedway Officials shall be empowered to permit minor deviations from any of the specifications herein or impose any further

More information

2017 Mini Sprint Rules

2017 Mini Sprint Rules 2017 Mini Sprint Rules In lieu of the new generation higher horse power engines being release for purchase at attractive prices and in fairness to all Western Outlaws owners the engine specifications will

More information

Colorado National Speedway Rules: Mod Coupes Last Revised: February 16, 2018

Colorado National Speedway Rules: Mod Coupes Last Revised: February 16, 2018 MOD COUPE RULES *** Please refer to General Section for rules and regulations applicable to all divisions*** Box Stock: The part must remain unaltered. No grinding, lightening, porting, or polishing of

More information

Lavonia Speedway 2018 Racing Season

Lavonia Speedway 2018 Racing Season Lavonia Speedway 2018 Racing Season Stock 4 Cylinder- (Window Safety Net & Mufflers are Mandatory) (*note 2 engine combinations*) BODY - A. Stock auto only B. May have complete aluminum body C. Inner panel

More information

2019 FIGURE 8 RULES INDEX

2019 FIGURE 8 RULES INDEX 2019 FIGURE 8 RULES INDEX Battery Body Engine Exhaust System Firewall Fuel Cell Frame Ignition System Rear End Roll Cage Seats Starter Suspension Transmission Weight Rules Wheels and Tires Page 7 Page

More information

2009 PASS MOD Rules MODS Tire Policy

2009 PASS MOD Rules MODS Tire Policy 2009 PASS MOD Rules 2009 MODS Tire Policy The American Racer 9 EC83 left and EC84 right is the mandated tire for the 2009 race season. All tires must be purchased through Northern Race Tire. Each team

More information

Larry King Law s Langley Speedway 2018 Super Street Division Rules

Larry King Law s Langley Speedway 2018 Super Street Division Rules Larry King Law s Langley Speedway 2018 Super Street Division Rules 1. COMPETING MODELS: A. Any American made 1979 through 1988 two door, coupe with a minimum 108 inch wheelbase. B. Cars must have a full

More information

Late Model Sportsman Car Specifications

Late Model Sportsman Car Specifications 15112 National Pike, Hagerstown, MD 21740 PHONE (301) 582-0640 FAX (301) 582-3618 info@hagerstownspeedway.com Late Model Sportsman Car Specifications CAR SPECIFICATIONS: LUCAS OIL AND WORLD OF OUTLAW LATE

More information

Single Engine Modified Tractors

Single Engine Modified Tractors Single Engine Modified Tractors For this class we will follow the Indiana Pulling League Rules. Payouts $1000 total for the class A. Weight Class 5,800 lb. B. Specifications 1. Only one naturally aspirated

More information

RACECEIVERS MANDATORY: TRANSPONDERS MANDATORY: IT IS THE DRIVERS RESPONSIBILITY TO HAVE THEM IN WORKING ORDER TO RACE AT THUNDERBIRD RACEWAY.

RACECEIVERS MANDATORY: TRANSPONDERS MANDATORY: IT IS THE DRIVERS RESPONSIBILITY TO HAVE THEM IN WORKING ORDER TO RACE AT THUNDERBIRD RACEWAY. General Pro Street Rules 2019 It is the sole responsibility of each competitor for the effectiveness and proper installation of safety equipment per the manufacturer s specifications to be adequate for

More information

2017 Thunder Series 602 Thunder Series Rules

2017 Thunder Series 602 Thunder Series Rules 2017 Thunder Series 602 Thunder Series Rules Chassis: 1. Must follow FASTRAK rules. 2. Chassis must be built prior to 2014 Body: 1. Must follow FASTRAK body rules 2. 8 spoiler permitted 3. No 12 side braces

More information

LONE STAR SPEEDWAY 2015 OPEN WHEEL MODIFIED

LONE STAR SPEEDWAY 2015 OPEN WHEEL MODIFIED RULES & SPECIFICATIONS - 2015 updates in RED LONE STAR SPEEDWAY 2015 OPEN WHEEL MODIFIED 1/6/15 UPDATES: 5" spoiler. 8000 RPM chip. 2,350# after the race with the driver (whether steel or alum. head).

More information

2014 SLED PULL Rules and Regulations

2014 SLED PULL Rules and Regulations Maximum weight of 7500lbs with driver. Diesel Super Stock Trucks 2014 SLED PULL All drivers must wear a helmet (Must have helmet meeting Snell SA2005, K2005, M2005, SA2010, SAH2010, K2010, M2010 or SFI

More information

2018 FWD Compact Rules (pending)

2018 FWD Compact Rules (pending) 2018 FWD Compact Rules (pending) The following specifications are shared with you and are similar to other Thunder Car specifications at other speedways. The rules are meant serve as guidelines for the

More information

WILD BILL S RACEWAY MODIFIED RULES 2010

WILD BILL S RACEWAY MODIFIED RULES 2010 WILD BILL S RACEWAY MODIFIED RULES 2010 1. SAFETY: Snell 2000 helmet required and must be worn at all times car is on track (SA 2005 recommended). Roll bar padding (fire retardant recommended) driver compartment.

More information

Larry King Law Langley Speedway 2018 Pro-Six Division Rules

Larry King Law Langley Speedway 2018 Pro-Six Division Rules Larry King Law Langley Speedway 2018 Pro-Six Division Rules Amendments: Rules are subject to amendments at any time when ample notice has been given to enhance competition 1. Chassis, Frame Rails and Roll

More information

THIS CLASS IS TO REMAIN STOCK APPEARRING WITH ALL COMPONENTS IN STOCK LOCATION

THIS CLASS IS TO REMAIN STOCK APPEARRING WITH ALL COMPONENTS IN STOCK LOCATION SOUTHERN OREGON SPEEDWAY Website: www.sospeedway.com 2013 STREET STOCK RULES THIS CLASS IS TO REMAIN STOCK APPEARRING WITH ALL COMPONENTS IN STOCK LOCATION 1. MODELS: A. American sedans and hardtops. Station

More information

Mini-Stock Rules GENERAL BODY REQUIREMENTS:

Mini-Stock Rules GENERAL BODY REQUIREMENTS: Mini-Stock Rules 1/24/2019 Eligible Cars: 1. Four cylinder, front or rear wheel drive COMPACT CARS ONLY. 2. No full-size cars allowed. No SUVs, cross-overs, or vans permitted. 3. Wheelbase must be between

More information

PRO-4 MODIFIEDS 2017 RULES

PRO-4 MODIFIEDS 2017 RULES PRO-4 MODIFIEDS 2017 RULES 1. CAGES / CHASSIS a. Fabricated Chassis only. b. Minimum 1 1/2" Diameter.095 wall tubing. c. Must be 4-post cage with a minimum of 3 U-shaped door bars on drivers side; door

More information

RaceCeiver Required, NO other radios or communication equipment or mirrors allowed at any time.

RaceCeiver Required, NO other radios or communication equipment or mirrors allowed at any time. RULES UCRA 602/SPORTSMAN SERIES Double file re-starts for the 2017 season RaceCeiver Required, NO other radios or communication equipment or mirrors allowed at any time. A. BODY RULE: same as super late

More information

STREET STOCK & CYCLONES COMBINED RULES

STREET STOCK & CYCLONES COMBINED RULES 2019 STREET STOCK & CYCLONES COMBINED RULES In 2019 we are combining the street stocks and the cyclones into one division. We have been working hard on trying to incorporate the rules to make this a fair

More information

2018 Senoia Raceway Rulebook Late Model Sportsman

2018 Senoia Raceway Rulebook Late Model Sportsman (Formerly B Cadet) All drivers must adhere to the general rules, in addition to the division specific rules set forth below. BODY 1. Stock appearing body may be aluminum or steel. 2. Rear of body may be

More information

2015 SLED PULL Rules and Regulations

2015 SLED PULL Rules and Regulations Super Stock Diesel Trucks Maximum weight of 7500lbs with driver. All drivers must have a valid state driver s license OEM or equivalent SFI restraint system is mandatory and must be worn. 2015 SLED PULL

More information

WMMP RULES: Dwarf Car

WMMP RULES: Dwarf Car WMMP RULES: Dwarf Car 2019 01.24.19 You may run no more than a 1000cc motor, must be approved by director of competition. WMMP Speedway dwarf cars shall hereafter be referred to as WMMPDC throughout the

More information

Other model rear wheel drive cars are restricted to a maximum 3.8 litre motor and may not lock the rearend.

Other model rear wheel drive cars are restricted to a maximum 3.8 litre motor and may not lock the rearend. ROAD RUNNERS All persons must be approved for competition by the management of BRMS. Any person may be denied the ability to compete in this division based solely upon the opinion of the management of

More information

STOCK DIESEL TRUCK RULES Rules for 2015 Pulling Season

STOCK DIESEL TRUCK RULES Rules for 2015 Pulling Season ALMONTE TRUCK & TRACTOR PULL STOCK DIESEL TRUCK RULES Stock Diesel Trucks: 1) Any member caught in default of the following rules will have a one pull suspension for that pull. 2) WEIGHT for this class

More information

*IN ADDITION TO ALL GENERAL AND GENERAL SAFETY RULES, THE FOLLOWING CLASS RULES WILL APPLY.

*IN ADDITION TO ALL GENERAL AND GENERAL SAFETY RULES, THE FOLLOWING CLASS RULES WILL APPLY. FAST TRACK FAST TRACK CLASSES: STREET STOCK, HOT STOCK, ECONOMY 2-4 WHEELS, SUPER STOCK, SUPER GAS, SUPER GAS 410-474, 2 WHEELS MODIFIED, PROSTOCK 4 WHEELS MODIFIED, OUTLAW PROSTOCK, MODIFIED CUTS-4 WHEELS

More information

2017 FACTORY STOCK RULES

2017 FACTORY STOCK RULES 2017 FACTORY STOCK RULES The Statement: Unless it came on a stock, mass produced vehicle, it is NOT LEGAL UNLESS SPECIFIED HERE! If it came on a stock, mass produced vehicle and it is prohibited here,

More information

2018 SEASON LIMITED SPORTSMAN DIVISION

2018 SEASON LIMITED SPORTSMAN DIVISION 1188 James D. Hagood Hwy. P.O. Box 1066 South Boston, VA 24592 Office: 434-572- 4947 Fax: 434-575 - 8992 Email: info@southbostonspeedway.com www.southbostonspeedway.com 2018 SEASON LIMITED SPORTSMAN DIVISION

More information

2018 UCAR Rules. May 14, 2018

2018 UCAR Rules. May 14, 2018 2018 UCAR Rules May 14, 2018 RULE BOOK DISCLAIMER: The rules and/or regulations set forth herein are designed to provide for the orderly conduct of racing events and to establish minimum acceptable requirements

More information

Bilstein Modified Lite STARS JR Mod Lites Cup

Bilstein Modified Lite STARS JR Mod Lites Cup Bilstein Modified Lite STARS JR Mod Lites Cup Modified Lite STARS Racing Series, LLC 128 Bruner Ave Somerset, PA 15501 Phone: (814) 442-1738 http://modlitestars.org/ The rules and/or regulations set forth

More information

Grundy County Fair Old School Figure 8 Rules

Grundy County Fair Old School Figure 8 Rules Grundy County Fair Old School Figure 8 Rules General Rules Car and driver must be through inspection one (1) hour prior to the start of the race, or you will start at the back of a heat. A drivers pit

More information

2019 PURE STOCK RULES ALL CHANGES/MODIFICATIONS TO THE 2019 PURE STOCK RULES ARE IN RED.

2019 PURE STOCK RULES ALL CHANGES/MODIFICATIONS TO THE 2019 PURE STOCK RULES ARE IN RED. 2019 PURE STOCK RULES ALL CHANGES/MODIFICATIONS TO THE 2019 PURE STOCK RULES ARE IN RED. DRIVERS A. Driver must be at least 14 years of age. Must have Minor release form signed by parent or guardian on

More information

2018 SUPER PRO TRUCK RULES

2018 SUPER PRO TRUCK RULES 2018 SUPER PRO TRUCK RULES INDEX Battery Brake Components Bodys Competing Models Electrical Switches Engine Location Engine Option 1 - Crate Engine Option 2 - SPT Exhaust System Fuel Cell Frame Hood Ignition

More information

2019 Toccoa Raceway. Fuel: 110 or 114 NO OXYGENATED FUEL PERMITTED. Body:

2019 Toccoa Raceway. Fuel: 110 or 114 NO OXYGENATED FUEL PERMITTED. Body: 2019 Toccoa Raceway Stock 4 Cylinder (Window Safety Net & Mufflers are Mandatory) ** WEIGHT MUST BE POSTED ON THE TOP LEFT CORNER OF THE DRIVERS DOOR *** NUMBER MUST BE 3 TALL & VISIBLE Fuel: 110 or 114

More information

If you have any questions or concerns, please contact: Jeremy Gulley (845) or

If you have any questions or concerns, please contact: Jeremy Gulley (845) or If you have any questions or concerns, please contact: Jeremy Gulley (845) 887-4117 or blauser_4@yahoo.com Full size (STOCK V8 and RWD 6 cylinder) Compact (4 cylinder RWD or FWD and 6 cylinders FWD) General:

More information

Sportsman Truck Rules for Updated: 12/16/2017 Must be at least 14 years of age.

Sportsman Truck Rules for Updated: 12/16/2017 Must be at least 14 years of age. Sportsman Truck Rules for 2018 Updated: 12/16/2017 Must be at least 14 years of age. SNELL-RATED SA2005, SA2010, OR SA2015 HELMET REQUIRED. SFI-APPROVED FULL FIRE SUIT REQUIRED. FIRE RETARDANT GLOVES,

More information

2018 TOCCOA RACEWAY. Stock 4 Cyl. (Window Safety Net & Mufflers are Mandatory)

2018 TOCCOA RACEWAY. Stock 4 Cyl. (Window Safety Net & Mufflers are Mandatory) Stock 4 Cyl (Window Safety Net & Mufflers are Mandatory) Fuel: A) 110 Track Fuel B) NO OXYGENATED FUELS C) NO E85 Body: 2018 TOCCOA RACEWAY A) Any two or four door foreign or domestic car with a 94-101.5

More information

CYLINDER STREET STOCK RULES AND REGULATIONS. Spirit Auto Center SPEEDWAY

CYLINDER STREET STOCK RULES AND REGULATIONS. Spirit Auto Center SPEEDWAY 2018 4-CYLINDER STREET STOCK RULES AND REGULATIONS Spirit Auto Center SPEEDWAY GENERAL: 2018 4-CYLINDER STREET STOCK RULES AND REGULATIONS This information is to be used in addition to the general rules

More information