CERM Counter System troubleshooting

Size: px
Start display at page:

Download "CERM Counter System troubleshooting"

Transcription

1 CERM Counter System troubleshooting In this document, we will try to clarify different solutions for problems with the CERM Counter System after installation. Content Hardware modules (in the gray box) Check if the sensor receiver receives signals Check if the counter is started Check the fuses Check network connection Voltage difference ONLY U.S. Check if there is a magnetic device in the sensor neighborhood Check the UPS fuse Check dammage to the sensors Check the connection of the PLC Modules Check the SF Indicator Check wiring (Good/Bad) Hardware modules (in the gray box) The gray box contains 4 principal modules: PLC module Sensor receiver Counter network connector Power module Transformer Power indicator UPS Fuse module Cageclamp module(s) The gray box, somewhere on a wall in your company Inside the gray box (version 1) CERM gray box Troubleshooting pg. 1/8

2 In the second version of the gray box, the Power Module looks slightly different, but has exactly the same components: Power Indicator UPS Transformator (from left to right) Also, the fuse module looks slightly different in the 2 nd version, especially the black fuses: RED CONNECTOR Fuse Module (Complete) Fuse Module (Black fuses removed) Cabling has changed here compared to the first version of the gray box. Only 1 wire arrives, and 2 wires leave from the fuse holders. The fuse holders are connected with a red connector, which you can see on the right picture. CERM gray box Troubleshooting pg. 2/8

3 Checks: Do all these hardware checks before calling CERM! This are basic hardware checks that we can t do remote. - Check if the sensor receiver receives signals Step 1: Connect one end with a + clamp Step 2: Connect the other end with the pulse clamp Result: A green LED lights up on the sensor receiver. - Check if the counter is started The counter can be started or stopped. When the counter is stopped, an orange LED lights up. The counter is STARTED The counter is STOPPED CERM gray box Troubleshooting pg. 3/8

4 - Check the fuses There are 3 fuses in the gray box. General fuse The main fuse has to be turned ON. When the main fuse is turned OFF, the gray box could still be working. This is because the power indicator changes his source of electricity to the UPS. But this will work only for a few hours. Turned OFF. Turned ON Counter fuse and network connector fuse Next to the main fuse, there are 2 small fuses. One for the sensor receiver and one for the network connector and counter in the PLC module. Known issues: o A red LED lights up => a fuse is broken => change it with a new fuse.(*) o Everything works, except the counter and network connector OR the sensor receiver doesn t work => A wrapping isn t properly fixed => push on top of the wrapping. Normal fuses one broken fuse You can find the fuse here The fuse (*)Type of the fuse: Check the number on the bottom of the wrapping. 50F14: 500mA 50F17, 3 or less cageclamps (20 counters): 500mA 50F17, 4 cageclamps (30 counters): 1A Fast-acting fuses are required. CERM gray box Troubleshooting pg. 4/8

5 - Check the network connection If there is something wrong with the network connection, the BF red LED lights up on the network connector. The green LED RxTx lights up when there is a network connection. Known issues: o No network connection => Check network connection on both sides of the cable. The cable has to be in the same physical network as the datacap, only the IP range is different. No network connection Check network cable on network connector - Voltage difference ONLY U.S. There is a slider on top of the transformator to change the input voltage from 230V to 110V. - Check if there is a magnetic device in the sensor neighborhood If you have one of these problems: At random moments you don t receive counter data The counter data is not correct Check if there is a magnetic device (radio, electronic engine, )in the sensor neighborhood. The sensor is an induction sensor, a magnetic field can disturb the signal. CERM gray box Troubleshooting pg. 5/8

6 - UPS Fuse There is a small UPS inside the counter box. This UPS also has a fuse. If a red led lights up (see picture below),the fuse is broken. However, this should not influence the functionality of the counter system as long as there is power. This led lights up when the UPS fuse is broken You can find the UPS fuse here - Damage to sensors Check your sensors, there shouldn t be damage to the sensors. This is what we call a broken sensor: The damage can be hidden behind the nuts. CERM gray box Troubleshooting pg. 6/8

7 - Connection of the PLC Modules The PLC modules are connected with a connector at the back of the modules. One connector not connected 2 connecters correctly connected To check these connectors, the PLC modules can be loosened by loosening a screw at the bottom of the modules - SF LED lights up on PLC module The SF Indicator means System Failure. You will need to contact Cerm to solve this. CERM gray box Troubleshooting pg. 7/8

8 - Good/Bad Wiring When a Good/Bad switch is used, cabling need to be done like in the picture below. When for a press no Good/Bad signal is necessary (for example Press 3 in the picture), the port for the Good/Bad wire need to stay open. The port cannot be used for other purposes! CERM gray box Troubleshooting pg. 8/8

JBI Docupunch P33 Automatic Punch

JBI Docupunch P33 Automatic Punch JBI Docupunch P33 Automatic Punch Instruction Manual Provided By http://www.mybinding.com http://www.mybindingblog.com TABLE OF CONTENTS SECTION I: INSTALLATION & TESTING: 1) Uncrating, Inspection & removal

More information

Ignition Timing - Honda 180-Degree Twins

Ignition Timing - Honda 180-Degree Twins Ignition Timing - Honda 180-Degree Twins First thing to do is make a quick test light - I used a 12 volt indicator bulb from a speedo. Test leads with alligator clips make hookup easy... The point plate

More information

HOW TO USE A MULTIMETER, PART 4: MEASURING CURRENT (AMPERAGE)

HOW TO USE A MULTIMETER, PART 4: MEASURING CURRENT (AMPERAGE) HOW TO USE A MULTIMETER, PART 4: MEASURING CURRENT (AMPERAGE) By: Rob Siegel First, we discussed how to use a multimeter for measuring voltage, or simply verifying that voltage is present. Last week, we

More information

NEW WISDOM Miner's lamp booklet

NEW WISDOM Miner's lamp booklet NO.: 2000508-201 NEW WISDOM Miner's lamp booklet KL5M LED light Li-ion battery miner s safety lamp KL8M double filaments Li-ion battery miner s safety lamp Usage, maintenance and safety notes of the miner

More information

Z TECHNICAL INSTRUCTIONS

Z TECHNICAL INSTRUCTIONS ÍNDICE: Z40 2.0 TECHNICAL INSTRUCTIONS 1.- Error list 2.- Replace the control board 3.- Opening the machine 4.- Replace the power board 5.- Dismantling motor and gear box 6.- Assembly of gear box 7.- Pushing

More information

Assembly Instructions: Conventional Motor (Beakman's Motor Kit)

Assembly Instructions: Conventional Motor (Beakman's Motor Kit) Assembly Instructions: Conventional Motor (Beakman's Motor Kit) 1. Leave about 3" (7-8cm) and wind the wire 10-35 times around the AA battery. You do not have to be neat as some randomness does not affect

More information

RE Generation II Troubleshooting Guide Section I Preliminary Information and Evaluation

RE Generation II Troubleshooting Guide Section I Preliminary Information and Evaluation DODGE ENGINEERING & CONTROLS, INC. 196 Riverneck Road Chelmsford, MA 01824 PHONE (978) 244-1200 FAX (978) 244-1422 TOLL FREE (877) 334-2875 RE Generation II Troubleshooting Guide Section I Preliminary

More information

Repairing SpeedTreater-TX Spray Proximity Sensor

Repairing SpeedTreater-TX Spray Proximity Sensor Repairing SpeedTreater-TX Spray Proximity Sensor How to remove and replace the proximity sensor on the spray valve assembly. 2017 guides.equipmentzone.com Page 1 of 9 Step 1 Unscrew and Remove Top Cover

More information

Biasing the Vintage Series (Nomad, BelAir, VT50, Vintage 33)

Biasing the Vintage Series (Nomad, BelAir, VT50, Vintage 33) Biasing the Vintage Series (Nomad, BelAir, VT50, Vintage 33) This chapter will outline and guide you through the procedures of biasing the Vintage series amplifier. The procedures are broken down in a

More information

Fitting Radio Control to a Mamod Boulton

Fitting Radio Control to a Mamod Boulton Fitting Radio Control to a Mamod Boulton How To Fit Radio Control To A Mamod Boulton using FlySky Equipment I assume that you already have a Mamod Boulton and have fitted rechargeable AA batteries instead

More information

Depress each tab as you pull the bezel off. The bezels are tight. L.H. shown.

Depress each tab as you pull the bezel off. The bezels are tight. L.H. shown. 2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR

More information

LAB 7. SERIES AND PARALLEL RESISTORS

LAB 7. SERIES AND PARALLEL RESISTORS Name: LAB 7. SERIES AND PARALLEL RESISTORS Problem How do you measure resistance, voltage, and current in a resistor? How are these quantities related? What is the difference between a series circuit and

More information

AA4006 Speed Sensitive Trip Unit. User Manual

AA4006 Speed Sensitive Trip Unit. User Manual AA4006 Speed Sensitive Trip Unit User Manual Software Version 2.00 Issued 01/2005 Don Controls Limited Westfield Industrial Estate Kirk Lane, Yeadon Leeds, LS19 7LX Telephone: +44 (0)845 1304946 Fax: +44

More information

OPERATION MANUAL Common for All models Bobbin Sensor (Weft End Detection) DP150 - L2 BP150 - L2-12V BP150 - L2-24V (PNP/NPN)

OPERATION MANUAL Common for All models Bobbin Sensor (Weft End Detection) DP150 - L2 BP150 - L2-12V BP150 - L2-24V (PNP/NPN) OPERATION MANUAL Common for All models Bobbin Sensor (Weft End Detection) DP150 - L2 BP150 - L2-12V BP150 - L2-24V (PNP/NPN) Beta Computronics pvt. Ltd. 10/1 IT Park, Parsodi, Nagpur-440022 (MS), INDIA.

More information

USER S MANUAL CDL S AUTOMATIC DRAW-OFF VALVES. Les Équipements d Érablière CDL inc.

USER S MANUAL CDL S AUTOMATIC DRAW-OFF VALVES. Les Équipements d Érablière CDL inc. USER S MANUAL CDL S AUTOMATIC DRAW-OFF VALVES Thank you for choosing a CDL automatic draw off valve. Our 25 years of experience working with sugar makers ensures you that you acquired a performant and

More information

Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT)

Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT) Tools needed: 14mm hex socket 7mm socket/wrench 8mm socket/wrench Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT) 10mm socket (for airbox removal) ¾ inch or 19mm wrench Torque wrench Appropriate ratchets

More information

User Manual Digital Water Level Indicator for rain water storage tanks

User Manual Digital Water Level Indicator for rain water storage tanks User Manual Digital Water Level Indicator for rain water storage tanks We congratulate you on the purchase of Digital Water Level measuring device. You have purchased a high-quality product built to the

More information

WARNING: ALWAYS UNPLUG THE TREADMILL FROM THE ELECTRICAL OUTLET BEFORE SERVICING THE UNIT.

WARNING: ALWAYS UNPLUG THE TREADMILL FROM THE ELECTRICAL OUTLET BEFORE SERVICING THE UNIT. Z100-A81 CE Treadmill WARNING: ALWAYS UNPLUG THE TREADMILL FROM THE ELECTRICAL OUTLET BEFORE SERVICING THE UNIT. Table of Contents TABLE OF CONTENTS Table of Contents...1 Table of Figures...3 Description...4

More information

Bruker BioSpin NMR CASE. Troubleshooting Guide. Version. NMR Spectroscopy. think forward

Bruker BioSpin NMR CASE. Troubleshooting Guide. Version. NMR Spectroscopy. think forward Bruker BioSpin NMR CASE Troubleshooting Guide Version 021 think forward NMR Spectroscopy Copyright by Bruker BioSpin NMR GmbH All rights reserved. No part of this publication may be reproduced, stored

More information

Chapter 7: DC Motors and Transmissions. 7.1: Basic Definitions and Concepts

Chapter 7: DC Motors and Transmissions. 7.1: Basic Definitions and Concepts Chapter 7: DC Motors and Transmissions Electric motors are one of the most common types of actuators found in robotics. Using them effectively will allow your robot to take action based on the direction

More information

Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List:

Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: 2015-2017 Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: LED Foglights/ Bezels 2 Flat head & Phillips screwdriver (if you ordered part#3600) Ratchet & Socket set OR Wiring harness

More information

troubleshooting guide Robotic Massage Chair

troubleshooting guide Robotic Massage Chair troubleshooting guide ijoy 2580 Robotic Massage Chair June 29, 2009 2009 Human Touch, LLC. All rights reserved. Please forward any questions or comments regarding this Troubleshooting Guide to documentation@humantouch.com.

More information

WARNING: ALWAYS UNPLUG THE TREADMILL FROM THE ELECTRICAL OUTLET BEFORE SERVICING THE UNIT.

WARNING: ALWAYS UNPLUG THE TREADMILL FROM THE ELECTRICAL OUTLET BEFORE SERVICING THE UNIT. Z700-A82 / 120V Treadmill WARNING: ALWAYS UNPLUG THE TREADMILL FROM THE ELECTRICAL OUTLET BEFORE SERVICING THE UNIT. Table of Contents TABLE OF CONTENTS Table of Contents...1 Table of Figures...3 Description...4

More information

Splice-In Mustang MIL Eliminators (96-04 GT) - Installation Instructions

Splice-In Mustang MIL Eliminators (96-04 GT) - Installation Instructions Splice-In Mustang MIL Eliminators (96-04 GT) - Installation Instructions The below installation instructions work for the following products: Splice-In Mustang MIL Eliminators (96-04 GT) Please read through

More information

Deegan 38 HD Rock Sliders w/ LED Rock Lights (07-18 Wrangler JKU)

Deegan 38 HD Rock Sliders w/ LED Rock Lights (07-18 Wrangler JKU) Installation Time: 2-3 Hours Deegan 38 HD Rock Sliders w/ LED Rock Lights (07-18 Wrangler JKU) Note: This kit comes with everything you need to wire the lights with a switch in the cab. However, I recommend

More information

Remove black panel shown. Save 6 retaining pins for re-install later. Pry up on center part of pin first. Then pry out entire retaining pin.

Remove black panel shown. Save 6 retaining pins for re-install later. Pry up on center part of pin first. Then pry out entire retaining pin. 2005-2009 Ford Mustang V6 Fog Light Wiring Kit Parts List: Quantity: Tools Required: Wiring harness 1 Flat head screwdriver Supplemental wire leads 2 Ratchet & Socket set OR Wire tap red 2 Adjustable Wrench

More information

X-Type w/ non-premium sound amplifier installation instructions

X-Type w/ non-premium sound amplifier installation instructions X-Type w/ non-premium sound amplifier installation instructions 1. Pull radio from dash (see Radio Removal Instructions ) 2. Disconnect wiring harness from back of radio by pushing in tab on plug and pulling

More information

Throttle Cable Pull - Patent Pending By: NetGain Controls, Inc.

Throttle Cable Pull - Patent Pending By: NetGain Controls, Inc. Throttle Cable Pull - Patent Pending By: NetGain Controls, Inc. Powering the future! Installation Guide 2011 All Rights Reserved NetGain Controls, Inc. 1 of 8 Introduction Thank you for purchasing a NetGain

More information

SERVICE MANUAL. Standard Horizon PF-P310 Paper Folder

SERVICE MANUAL. Standard Horizon PF-P310 Paper Folder SERVICE MANUAL Standard Horizon PF-P310 Paper Folder Read this manual, and thoroughly familiarize yourself with its contents before operating or servicing this equipment. PF-P310/SM FOREWORD Paper Folder

More information

SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL

SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL Items Supplied with the System: Installation Instructions: Main unit 1. Mounting the module: Plug In LED Mount the module in a suitable location

More information

Instructions For PG-1200RC Magnetic Locking Devices

Instructions For PG-1200RC Magnetic Locking Devices Instructions For PG-1200RC Magnetic Locking Devices (Remote control distance up to 10 meters) Ver. 18.1 Please Read Carefully Before Installing Magnetic Lock A. Carefully for handling to prevent damage

More information

WALKING TREADMILL SF-T1407M USER MANUAL

WALKING TREADMILL SF-T1407M USER MANUAL WALKING TREADMILL SF-T1407M USER MANUAL IMPORTANT! Please retain owner s manual for maintenance and adjustment instructions. Your satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE

More information

750 Paso Wiring Upgrade

750 Paso Wiring Upgrade 750 Paso Wiring Upgrade Supplies required: 2 Bosch 30A/12V Relays # #0 332 209 150 (with mounting tab) 1 30 Amp fuse holder 1 10 Amp fuse holder 12 inches of brown 12 gauge wire 60 inches of red 14 gauge

More information

DODGE OFF ROAD T-STYLE STEERING KIT INSTALLATION INSTRUCTIONS

DODGE OFF ROAD T-STYLE STEERING KIT INSTALLATION INSTRUCTIONS Dodge Off Road, LLC Specializing in Dodge Ram Solid-Axle 4x4 Suspension and Steering for Off Road Applications 855.9009.DOR sales@dodgeoffroad.com dodgeoffroad.com DODGE OFF ROAD T-STYLE STEERING KIT INSTALLATION

More information

Kodak 750H Carousel Projector Repair

Kodak 750H Carousel Projector Repair Kodak 750H Carousel Projector Repair An AT YOUR OWN RISK PROJECT by Klaus Wolter, Rev B, 3-26-2016 Here I documen the repair of my 750H carousel. A common problem with this projector, and all of the projectors

More information

Switch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, Heavy Duty Safety Switches

Switch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, Heavy Duty Safety Switches Step Switch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, Heavy Duty Safety Switches Work Description All work should be performed in accordance with NFPA 70E. Tools Required: Personal Protective

More information

MBM8 / MBM11- Barriers. Installer and User s manual

MBM8 / MBM11- Barriers. Installer and User s manual MBM8 / MBM11- Barriers Installer and User s manual v2.0 REV. 01/2014 00. CONTENT 01.SAFETY INSTRUCTIONS INDEX 00. CONTENT index page 01.A 01. SAFETY INSTRUCTIONS standards to follow page 01.B 02. PACKAGE

More information

TachMatch Instructions

TachMatch Instructions TachMatch Instructions Thank you for your purchase of the TachMatch Model TM01 from TechnoVersions LLC. The TachMatch has been designed to: accept various tachometer input signals (e.g., coil, MSD, HEI),

More information

MSD 6AL Ignition Module w/ Rev Control - Installation Instructions

MSD 6AL Ignition Module w/ Rev Control - Installation Instructions MSD 6AL Ignition Module w/ Rev Control - Installation Instructions The below installation instructions work for the following products: MSD 6AL Ignition Module w/ Rev Control Please read through the instructions

More information

LIPPERTCOMPONENTS, INC.

LIPPERTCOMPONENTS, INC. LIPPERTCOMPONENTS, INC. SCHWINTEK INWALL SLIDEOUT SYSTEM OPERATION AND SERVICE MANUAL Contents I. Controls 1-1 System components 1 1-1A versions C1 & C2 2 1-2 Motor wiring harness connections 3 1-3 Extend

More information

PAGE 1. TES Operation & Testing Guidelines: Tes Trouble shooting

PAGE 1. TES Operation & Testing Guidelines: Tes Trouble shooting PAGE 1 This document outlines questions to ask and components to check during TES troubleshooting. More detailed troubleshooting procedures are available in the TES Troubleshooting Guide. 1. Flow Light

More information

Switch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, w Neutral, Visible-Blade, Heavy Duty Safety Switches

Switch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, w Neutral, Visible-Blade, Heavy Duty Safety Switches Step Switch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, w Neutral, Visible-Blade, Heavy Duty Safety Switches Work Description All work should be performed in accordance with NFPA 70E. Tools

More information

Dosing Pump Operational Manual

Dosing Pump Operational Manual Chemical Dosing Specialists Dosing Pump Operational Manual Pump Range WMPSP0110 - WMPSP0408 - WMPSP0607 - WMPSP0805 - WMPSP1204 - WMPSP1502 - WMPSP2001 1- Product Introduction 2 1.1 Product Overview 2

More information

Energy-saving Servo Motor

Energy-saving Servo Motor Energy-saving Servo Motor User Guide Perface GAUTION: PLEASE READ INSTEUCTION MANUAL CAREFULLY BEFORE OPERATEING. THE INSTALLATION AND OPERATION MUST BE OPERATE UNDER PROFESSIONAL TRAINED STAFF. This product

More information

Hitachi Alternator Upgrade for Series I E-Types Ray Livingston (831) Home (831) Cell

Hitachi Alternator Upgrade for Series I E-Types Ray Livingston (831) Home (831) Cell Hitachi Alternator Upgrade for Series I E-Types Ray Livingston (831) 457-1373 Home (831) 234-0858 Cell rayl@atc.creative.com The Hitachi alternator for a 1986 Nissan pickup is a perfect replacement for

More information

PHY152H1S Practical 3: Introduction to Circuits

PHY152H1S Practical 3: Introduction to Circuits PHY152H1S Practical 3: Introduction to Circuits Don t forget: List the NAMES of all participants on the first page of each day s write-up. Note if any participants arrived late or left early. Put the DATE

More information

Instructions for repairing the F-Body Hatch Pull-Down Unit By Lon Salgren (ls90rs)

Instructions for repairing the F-Body Hatch Pull-Down Unit By Lon Salgren (ls90rs) Instructions for repairing the 1986-87 F-Body Hatch Pull-Down Unit By Lon Salgren (ls90rs) Lonsal@adelphia.net CAUTION: Completely read and understand the instructions before proceeding. There are some

More information

High technology theft-prevention systems

High technology theft-prevention systems Lemme In! Mazda 626 & MPV Immobilizer System High technology theft-prevention systems have hit the automotive market full-force. Several manufacturers now offer antitheft protection integrated with the

More information

Turny Evo. Autoadapt. Seat lift. Installation manual

Turny Evo. Autoadapt. Seat lift. Installation manual Turny Evo Autoadapt Seat lift EN Installation manual Getting seated Turny Evo Thank you for choosing a Turny Evo from Autoadapt! The manual that follows is an integral, important part of the product,

More information

J&M Mustang Rear Lower Control Arms (2005+) - Installation Instructions

J&M Mustang Rear Lower Control Arms (2005+) - Installation Instructions J&M Mustang Rear Lower Control Arms (2005+) - Installation Instructions The below installation instructions work for the following products: J&M Mustang Rear Lower Control Arms (2005+) Please read through

More information

G203V / G213V MANUAL STEP MOTOR DRIVE

G203V / G213V MANUAL STEP MOTOR DRIVE G203V / G213V MANUAL STEP MOTOR DRIVE PRODUCT DIMENSIONS PHYSICAL AND ELECTRICAL RATINGS Minimum Maximum Units Supply Voltage 18 80 VDC Motor Current 0 7 A Power Dissipation 1 13 W Short Circuit Trip 10

More information

Installation Manual DELT. Platform stairlift. Web: Tel: Mobile:

Installation Manual DELT. Platform stairlift. Web:   Tel: Mobile: Installation Manual DELT Platform stairlift Web: www.lehner-lifttechnik.at Tel: +4372783514 Email: office@lehnerlifttechnik.at Mobile: +436641612980 Table of content OBSERVE THE FOLLOWING POINTS BEFORE

More information

Arrow Shark TS760-Marine Onboard E-Starter. Owner Manual

Arrow Shark TS760-Marine Onboard E-Starter. Owner Manual Arrow Shark TS760-Marine Onboard E-Starter Owner Manual The TS760-Marine Onboard E-Starter has concluded years of experience Arrow Shark has on RC boat onboard E-Starter, it will work for about all brands

More information

Toyota 4RUNNER With/MR Overhead Video

Toyota 4RUNNER With/MR Overhead Video Toyota 4RUNNER With/MR 2010-10.2 Overhead Video Part Number: 00016-00110; Fit Kit-00110-14, Beige 00016-00120; Fit Kit-00120-14, Gray Accessory Code: ED7 Conflicts: Vehicles without a sunroof Kit Contents:

More information

Electronic Dynamo Regulator INSTRUCTION MANUAL. COPYRIGHT 2014 CLOVER SYSTEMS All Rights Reserved

Electronic Dynamo Regulator INSTRUCTION MANUAL. COPYRIGHT 2014 CLOVER SYSTEMS All Rights Reserved DRM TM DRM-HP TM Electronic Dynamo Regulator INSTRUCTION MANUAL COPYRIGHT 2014 CLOVER SYSTEMS All Rights Reserved INTRODUCTION The Clover Systems DRM is a state-of-the art all-electronic voltage and current

More information

POLAR BT INSTALLATION MANUAL FOR SKODA OCTAVIA (1Z)

POLAR BT INSTALLATION MANUAL FOR SKODA OCTAVIA (1Z) POLAR BT INSTALLATION MANUAL FOR SKODA OCTAVIA (1Z) I N D E X 1. BEGINNING 2 2. DISASSEMBLY 3 3. HOW TO CONNECT POLAR BT 10 4. FINISHING THE INSTALLATION 13 Polar BT Installation manual Rev. A Sheet :

More information

SMART LAB PUTTING TOGETHER THE

SMART LAB PUTTING TOGETHER THE PUTTING TOGETHER THE SMART LAB INSTALLING THE SPRINGS The cardboard workbench with all the holes punched in it will form the base to the many cool circuits that you will build. The first step in transforming

More information

Maserati GranSport Drive by Wire installation

Maserati GranSport Drive by Wire installation Maserati GranSport Drive by Wire installation Phil Vincenzes MaseratiLife member Vincenzo Email: Phil.Vincenzes@hotmail.com This write-up is not intended in any way to replace the detailed instructions

More information

TX80-Series FLOW SENSOR INSTRUCTIONS TX81 TX :2008 ISO CERTIFIED COMPANY TX80-SERIES FLOW SENSOR INSTRUCTIONS

TX80-Series FLOW SENSOR INSTRUCTIONS TX81 TX :2008 ISO CERTIFIED COMPANY TX80-SERIES FLOW SENSOR INSTRUCTIONS TX80-SERIES FLOW SENSOR INSTRUCTIONS TX80-Series FLOW SENSOR INSTRUCTIONS TX81 TX82 9 001:2008 ISO CERTIFIED COMPANY TABLE OF CONTENTS General Information Specifications, Features...Page 1 Installation

More information

reflect energy: the ability to do work

reflect energy: the ability to do work reflect Have you ever thought about how much we depend on electricity? Electricity is a form of energy that runs computers, appliances, and radios. Electricity lights our homes, schools, and office buildings.

More information

Table of Contents. Bikes with 2 handlebar switches. 12-pin plug for BMW models Installation tips. 15-pin plug for older BMW models Installation tips

Table of Contents. Bikes with 2 handlebar switches. 12-pin plug for BMW models Installation tips. 15-pin plug for older BMW models Installation tips Table of Contents Bikes with 2 handlebar switches SM-5 12-pin plug for BMW models Installation tips 2 3 SM-6 15-pin plug for older BMW models Installation tips Special Features & Functions 4 5 4-Way Emergency

More information

Service Manual Gulf Stream Electronic Full Wall Slide Systems

Service Manual Gulf Stream Electronic Full Wall Slide Systems Service Manual Gulf Stream Electronic Full Wall Slide Systems CONTENTS Page Before you operate the slide system 2 Operating Instructions 3 Preventive maintenance 3 Manually overriding your slide system

More information

Ford Mustang GT-Style Fog Light Kit Parts List: Quantity: Tool List:

Ford Mustang GT-Style Fog Light Kit Parts List: Quantity: Tool List: 2013-2014 Ford Mustang GT-Style Fog Light Kit Parts List: Quantity: Tool List: Fog light (Left& Right) 2 Flat head & Phillips screwdriver Upper grille with surround 1 Ratchet & Socket set OR Lower grille

More information

All of the control valves that we install the Mk. 16IQ positioner on are factory calibrated for proper operation prior to shipment.

All of the control valves that we install the Mk. 16IQ positioner on are factory calibrated for proper operation prior to shipment. 1 Troubleshooting The first thing you need is information... Try to find out what is wrong and why. Getting a serial number (found on the valve tag (see above)) and application parameters are always helpful

More information

Intelli-Feed Controller User s Manual Intelli-Feed Digital Tachometer and Hourmeter

Intelli-Feed Controller User s Manual Intelli-Feed Digital Tachometer and Hourmeter Intelli-Feed Controller User s Manual Intelli-Feed Digital Tachometer and Hourmeter Part #: 9047 Table of Contents: Table of Contents 2 Intelli-Feed TM User Interface 3 Equipment Diagnostic Indicators

More information

Audi A8 ( ) MMI swivelling unit repair manual

Audi A8 ( ) MMI swivelling unit repair manual Audi A8 (2003-2007) MMI swivelling unit repair manual Tools which you will need: two pcs screwdriver (any kind, for vent removing ) (you can cover the metal part with any tape to prevent making scratches

More information

Troubleshooting Guide for Okin Systems

Troubleshooting Guide for Okin Systems Troubleshooting Guide for Okin Systems More lift chair manufacturers use the Okin electronics system than any other system today, mainly because they re quiet running and usually very dependable. There

More information

TROUBLESHOOTING TP. Index

TROUBLESHOOTING TP. Index TROUBLESHOOTING TP Index E1 POWER CUT DETECTED... 2 E2 LOCK ERROR... 3 E3 DRAINAGE FAILURE / WATER IN TUB... 6 E4 MAXIMUM WATER LEVEL REACHED... 6 E5 FAULT WATER INLET... 6 E6 HEATING FAULT... 6 E7 MAXIMUM

More information

METROLOGIC INSTRUMENTS, INC. MX001 Industrial Control Interface Installation and User s Guide

METROLOGIC INSTRUMENTS, INC. MX001 Industrial Control Interface Installation and User s Guide METROLOGIC INSTRUMENTS, INC. MX001 Industrial Control Interface Installation and User s Guide Copyright 2007 by Metrologic Instruments, Inc. All rights reserved. No part of this work may be reproduced,

More information

Notice Regarding this Upgrade. WARNING! Danger Potential

Notice Regarding this Upgrade. WARNING! Danger Potential Notice Regarding this Upgrade WARNING! Danger Potential Although this kit has been designed to be easy-to-install, and has been tested in many installations; caution must be exercised when installing this

More information

STEP BY STEP INSTALLATION INSTRUCTIONS. Pleated Shades. Standard Control, Top Down/Bottom Up & Standard 2-on-1

STEP BY STEP INSTALLATION INSTRUCTIONS. Pleated Shades. Standard Control, Top Down/Bottom Up & Standard 2-on-1 STEP BY STEP INSTALLATION INSTRUCTIONS Pleated Shades Standard Control, Top Down/Bottom Up & Standard 2-on-1 Everything You Need A Smooth Set-Up We want you to love your new window coverings and that includes

More information

INSTRUCTION MANUAL ACTUATOR CLASSE I TYPE MA, MB

INSTRUCTION MANUAL ACTUATOR CLASSE I TYPE MA, MB ACTUATOR CLASSE I TYPE MA, MB CONTENTS Page : 2/13 PRODUCT DESCRIPTION General description 3 Product specification 5 INSTALLATION Storage 6 Unpacking 7 Handling 7 Installation : Mechanical 7 Installation

More information

CPi. CoiL PACK IGNiTioN FOR AViATiON. For 4,6 and 8 cylinder 4 stroke applications. Please read the entire manual before beginning installation.

CPi. CoiL PACK IGNiTioN FOR AViATiON. For 4,6 and 8 cylinder 4 stroke applications. Please read the entire manual before beginning installation. 1 CPi CoiL PACK IGNiTioN FOR AViATiON Coil pack (4 cylinder) Coil pack (6 cylinder) For 4,6 and 8 cylinder 4 stroke applications. Please read the entire manual before beginning installation. Software version

More information

Avoiding Crashes 5 tips to save your RC airplane! Sep 03, 2011 By Gerry Yarrish

Avoiding Crashes 5 tips to save your RC airplane! Sep 03, 2011 By Gerry Yarrish Avoiding Crashes 5 tips to save your RC airplane! Sep 03, 2011 By Gerry Yarrish We ve all been here, done that! The life expectancy of your RC airplane is directly proportional to how well you follow directions.

More information

Do isolate the power supply from other high power systems such as Stereos and Alarms

Do isolate the power supply from other high power systems such as Stereos and Alarms Thank you for purchasing a Smart Ride Air Management System, AIRBAGIT.COM s premier flagship product. This system will meet all of your custom and utility needs and will provide you years of trouble free

More information

CAPTUREPRO USER GUIDE FOR TESLA MODEL S, MODEL X, AND MODEL 3. Updated: September Power12 and CapturePro by Power12 Company v1.

CAPTUREPRO USER GUIDE FOR TESLA MODEL S, MODEL X, AND MODEL 3. Updated: September Power12 and CapturePro by Power12 Company v1. CAPTUREPRO FOR TESLA MODEL S, MODEL X, AND MODEL 3 USER GUIDE Updated: September 2018 Power12 and CapturePro 2013 2018 by Power12 Company v1.2 Table of Contents CapturePro Purpose and Design... 3 Why was

More information

PY600AC Sliding Gate Opener User Manual

PY600AC Sliding Gate Opener User Manual PY600AC Sliding Gate Opener User Manual 2017 Dear users, Thank you for choosing this product. Please read the manual carefully before assembling and using it. Please do not leave out the manual if you

More information

G213V STEP MOTOR DRIVE REV 7: March 25, 2011

G213V STEP MOTOR DRIVE REV 7: March 25, 2011 Thank you for purchasing the G213V drive. The G213V is part of Geckodrive s new generation of CPLD-based microstep drives. It has short-circuit protection for the motor outputs, over-voltage and under-voltage

More information

*Some speedometers have these additional electronic connections. If yours does, then remove the smaller slotted screws shown.

*Some speedometers have these additional electronic connections. If yours does, then remove the smaller slotted screws shown. www.odometergears.com 1981-1985 240 Cable-Driven Speedometers (NOT for 1986 and later electronic units) http://www.davebarton.com/240-odometer-repair.html For this set of instructions below, I will not

More information

EVO-1162 EVO Tailgate Tire Carrier

EVO-1162 EVO Tailgate Tire Carrier EVO-1162 EVO Tailgate Tire Carrier Bill of Materials EVO-1162 Tailgate Tire Carrier Part number Description Quantity EVO-12161 EVO Tailgate Tire Carrier 1 EVO-12162 Bolt Plate 1 EVO-12163 Wheel Mount 1

More information

CONTROL BOX. Wiring the control box into the vehicle. +12V

CONTROL BOX. Wiring the control box into the vehicle. +12V CONTROL BOX Once the display panel is in place, mount the control box within the connecting cable's distance (approximately 3 feet) and secure to the underside of the dashboard. This case does not have

More information

Helpdesk Tool. KaVo MASTER- and EXPERTsurg

Helpdesk Tool. KaVo MASTER- and EXPERTsurg 1 Helpdesk Tool KaVo MASTER- and EXPERTsurg Please select your device on the pictures 2 3 Overview MASTERsurg: Please select one category 4 Please select one category: 1. Instrument / 2. Motor / 3. Motor

More information

M SERIES Multi-Jet Cold Water Meter

M SERIES Multi-Jet Cold Water Meter M SERIES Multi-Jet Cold Water Meter /4 1 1-1/2" 2" Maximum Flow GPM 0 0 1 Minimum Flow GPM.2.7 1. 2.0 Maximum Operating Pressure 0 psi Maximum Operating Temperature F ( C) Also Available in Hot Water Applications

More information

Setup and Programming Manual

Setup and Programming Manual Microprocessor and Handy Terminal Setup and Programming Manual Versions U04 to U19 for Sliding Door Systems P/N 159000 Rev 7-2-07 The manufacturer, NABCO Entrances, Inc. suggests that this manual be given

More information

Installation Instructions PowerBoard Automatic Retracting Running Board

Installation Instructions PowerBoard Automatic Retracting Running Board Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Dodge Ram 1500 Crew Cab 2009 - Current : 75138-15 Dodge Ram 2500/3500 & HD Crew Cab 2010 - Current : 75138-15

More information

VECTRIX VX-2 SERVICE MANUAL. Version 1.0/May 2011 VECTRIX, LLC

VECTRIX VX-2 SERVICE MANUAL.   Version 1.0/May 2011 VECTRIX, LLC www.vectrix.com CONTENTS SECTION A: Tools 1 Tools Needed SECTION B: Mechanical Parts 1 Front Fairing 2 Front Console Cover 3 Speedometer Cover 4 Front Vertical Panel Cover-Lower 5 Front Vertical Panel

More information

2007-UP NAVIGATION INTERFACE MODULE (Infiniti/Nissan)

2007-UP NAVIGATION INTERFACE MODULE (Infiniti/Nissan) 2007-UP NAVIGATION INTERFACE MODULE (Infiniti/Nissan) ALTHOUGH THIS PRODUCT HAS BEEN THOROUGHLY TESTED KPIERSON TECHNOLOGIES ASSUMES NO RESPONSIBILITY FOR ANY DAMAGE THAT MAY RESULT BY THE INSTALLATION

More information

INSTALLATION & MAINTENANCE MANUAL

INSTALLATION & MAINTENANCE MANUAL A Subsidiary of Dynamic Instruments INSTALLATION & MAINTENANCE MANUAL A Subsidiary of Dynamic Instruments 3860 Calle Fortunada San Diego, CA 92123-1825 Phone: 1-(800) 821-5831 Web Site: hardyinst.com (858)

More information

Precision-24 Manual & Specification

Precision-24 Manual & Specification Precision-24 Manual & Specification 1 Product Introduction... - 1-1.1 Product Overview... - 1-1.2 Technical Parameter...- 2-1.2.1 General Parameter...- 2-1.2.2 Performance Parameter... - 3-1.2.3 Installation

More information

Electronic Dynamo Regulator INSTRUCTION MANUAL. COPYRIGHT 2014 CLOVER SYSTEMS All Rights Reserved

Electronic Dynamo Regulator INSTRUCTION MANUAL. COPYRIGHT 2014 CLOVER SYSTEMS All Rights Reserved DRM TM DRM-HP TM Electronic Dynamo Regulator INSTRUCTION MANUAL COPYRIGHT 2014 CLOVER SYSTEMS All Rights Reserved INTRODUCTION The Clover Systems DRM is a state-of-the art all-electronic voltage and current

More information

Gate & Door Controller with LCD and Intelligent Technology

Gate & Door Controller with LCD and Intelligent Technology 2nd Edition Gate & Door Controller with LCD and Intelligent Technology 24Sv1 and 12Sv1 Motor Controllers Setup and Technical information for single motor controller for gates & doors Includes latest Intelligent

More information

Unit 8 ~ Learning Guide Name:

Unit 8 ~ Learning Guide Name: Unit 8 ~ Learning Guide Name: Instructions: Using a pencil, complete the following notes as you work through the related lessons. Show ALL work as is explained in the lessons. You are required to have

More information

Remove four screws from radio trim

Remove four screws from radio trim ZSpeedPerformance Remove four screws from radio trim Radio trim removed, Remove 3 screws from shifter trim. The other screw is under the ash tray. Remove shift knob and remove shifter trim. Use caution

More information

How to replace or adjust the altitude clutch of the NexStar N11GPS

How to replace or adjust the altitude clutch of the NexStar N11GPS Langenbrettach/Germany, February 10 th 2004 Matthias Bopp How to replace or adjust the altitude clutch of the NexStar N11GPS Table of content How to replace or adjust the altitude clutch of the NexStar

More information

Informational Distribution List:

Informational Distribution List: Technical Bulletin 2017 Southern Technologies Corporation (STC). All rights reserved. Bulletin Number: TB-2017198-BW01 Date Published: 07/17/2017 Summary: Instructions for mounting, aligning and setting

More information

Trouble Shooting 1 The power light doesn't illuminate and the scooter doesn't run The power light is on and the scooter doesn't run.

Trouble Shooting 1 The power light doesn't illuminate and the scooter doesn't run The power light is on and the scooter doesn't run. Trouble Shooting 1.The power light doesn't illuminate and the scooter doesn't run 1) The output voltage is less than 35 V ± 1.0 V Use the multimeter to test the batteries for the voltage, if the voltage

More information

Manual for Control Panel

Manual for Control Panel - 1 - Manual for Control Panel ver.4.0 MODEL: BP2006 Pro.:2006.12.Rev.:2007.08 http://www.olb.kr - 2 - Contents. 1. Front Operation. 2. Parts Names. 3. Initial setting cost. 4. Temperature setting method.

More information

TC26-B Vehicle Sensor

TC26-B Vehicle Sensor Section 1 General Description The Model TC26-B is a microprocessor controlled vehicle sensor with a variable range. It is designed to trigger the operation of a traffic controller. The TC26-B will only

More information

Troubleshooting Guide

Troubleshooting Guide Troubleshooting Guide 1 TABLE OF CONTENTS How To Use Guide...3 Figure 1...4 Figure 2......5 Electrical Problems...6 Vacuum Motor Problems...8 Fragrance Delivery Problems...10 Timer Problems...15 Coin/Bill

More information

Merih DDCA60 Operation and User Manual I Merih Asansör A.Ş.

Merih DDCA60 Operation and User Manual I Merih Asansör A.Ş. 1. WARNINGS! CAUTION This manual contains user guidelines for Merih DDCA60 hardware version v1.05 and software version v1.03. This document will be updated with differences result from version differences.

More information