Daikin Daikin McQuay. SmartSource Single Stage Horizontal Water Source Heat Pump. WGSH 015, 019 Design 1

Transcription

1 Replacement Parts List No Revision N 10/2018 Daikin Daikin McQuay SmartSource Single Stage Horizontal Water Source Heat Pump WGSH 015, 019 Design 1 To find your Daikin Applied parts distributor, call or visit

2 Contents Parts List Revision History Nomenclature Serial Number... 5 Model Number Electrical Legend... 8 Unit Sections... 9 Return Air Configurations... 9 Blower Fan Assembly Refrigeration Circuit Diagrams...11 Components Hot Gas Reheat Water Flow Regulator Control Box- Microtech III Controls Diagrams Components MTIII Control Board Label Location Field Installed Accessories Critical Parts List... CPL1 WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 2

3 Parts List Revision History Rev. Date Description NEW 8/12 NEW A 10/12 Page 4- Add Code 13 Sound Packages A= Premium. Page 5- Code 23 add P= Controls for Electric Heat single 24V signal(field installed Duct Heater by Others) Page 10- Add Sound Blanket p/ns & Page 10- Change condensate pan p/ns to SERVSub p/ns. Change condensate pan p/ns to SERVSub p/ns. Delete all base pans. Page 12- Delete Series 2 from p/n & descriptions. Page 17- Add Electric Duct Heater Kit. CPL1- Delete Series 2 from p/n & descriptions. B 12/12 Page 10- Remove Sound Blanket p/ns and C 2/13 Page 11- Change Condenser to CO-AX Condenser and Cupro-Nickel to Copper. Change CO-AX Coil p/n to D 2/13 Page 12- Change MTIII control board p/n to Change I/O expansion board assy p/n to Change LonWorks com card p/n to Change BACnet com card p/n to Remove footnote. CPL1- Change MTIII control board p/n to ; I/O exp. board p/n to ; LonWorks card p/n to and BACnet card p/n to E 3/13 Page 9- Add 460V table for ECM motors. Change ECM motors from phantom p/ns to Program p/ns. Page 13- Remove Wire Harness Assy p/n from MTIII module kits. Page 14- Add Actuator p/n to 3-Way Valves rename Waterside Economizer. Rename 2-Way Valves to Motorized Valves. Page 15- Remove Boilerless System Kits and move sensors to Thermostats & Sensors. CPL1- Add 460V to ECM motors. F 10/13 Rebrand Daikin. Page 9- Add ECM motor size 015 p/n Page 12- Add LT sensors p/n CPL1- Add ECM motor size 015 p/n Change Reversing Valve. Add LT sensor. G 2/14 Page 12- Change H6 Connector p/n EGA9164 to H 10/14 Numerous drawing & p/n changes done. Separate vertical & horizontal units. Pages 4-6 Change to horizontal model configeration. Code changes to C03, C10, C43 & C44. Page 8- Delete Typical Refrigeration Cycle and add Unit Sections and Return Air Configerations. Page 9- Delete 460V ECM not used in size Ref #370 Change Qty from 1 to 3. Page 11- Change overload protector p/n to Change adapter p/n to Change fusible plug assy p/n to Page 12- Add Hot Gas Reheat and Water Flow Control. Page 14- Delete the control box BACnet & LonWorks p/ns & Page 15- Add footnote for field conversion kits LonWorks p/n & BACnet p/n Pages 16- Add Loop Pumps. Numerous hoses were added. CPL1- Delete BACnet & LonWorks p/ns & Delete 460V ECM. I 4/15 Page 9- Delete ECM p/ns and add nameplate diagram and footnote1. Page 14- Delete control board p/n and add footnte *. Change Ref# 315 Change I/O Exp Board p/n to CPL1- Delete control board and ECM p/ns. J 11/15 Rebrand Daikin. Page 14- Ref# 229 Add MTIII p/n Change Exp. Board p/n to Delete Disc. Switchs p/ns , , & Add handle p/n Add Relay p/n Delete Contactor p/n Add footnote for MTIII Controls Label Location. Page 15- Add MTIII Controls Label Location table and footnote. CPL1- Add MTIII p/n Delete Refrigeration Circuit. K 05/17 Page 14- Add yellow plug p/n ; white plug p/n and bridge connector p/n L CPL1- Update revision. 06/17 Page 4- Model Number changed to table format and SLP added to Serial Number. Page 17- Add WSE Coils, RH p/ns (until 03/15) & (03/15 & later) Add WSE Coils, LH p/ns (until 03/15) & (03/15 & later) CPL1- Update revision. M 12/17 Pages Add Ref # 240 & 238 relay p/ns & Page 18- Add 3 Ft. hoses. Page 19- Add boilerless system kit p/ns & CPL1- Update revision. Daikin Applied, Industrial Park Blvd., P.O. Box 1551, Minneapolis, MN (763) WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 3

4 Rev. Date Description N Parts List Revision History Continued 10/18 Page 4- Add Parts List Revision History page. Page 8- Electrical Legend updated. Page 12 Change Rev Valve size 015 p/n to and 019 p/n to Page 13- Add page. Change drain pan p/n to (LH) & (RH). Page 16- Add footnote for disconnect switch and delete unit size. Change size for capacitor Ref# 68 & 72. Delete Connector Bridge p/n , plug p/ns & Pages Numerous changes to Field Installed Accessories. Change filters from kit p/ns to single p/ns. Change WSE 3-way valve, LH p/n to CPL1- Update revision. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 4

5 Nomenclature Serial Number AUB U Plant Identification Abbreviation AUB = Auburn SLP = San Luis Potosi U= Unit Serial Number (build sequence) Week of Manufacture Year of Manufacture 12= = 2013 etc. Model Number WGSH 015 B 1 E WL R S 4 Y Y Y C S YYY B 2 A Y Y Y Y Code YY B D Y Y Y YYY Y YYY S Y Y B S Y A Y A T Y C Y YY Code Y Y 2 T Y S A L K Y Y Y Y YY Y Y A Y Y Y Y A A Y Code C Y Y YY FF ST ST YY YYY Y C Y Y YY 1 Code Code 01: Unit Type W= Water Source Heat Pump Code 02: Model Type GS= High Efficiency, Single Stage Code 03: Configuration H= Horizontal Code 04: Unit Size 015= BtuH Nominal Cooling 019= BtuH Nominal Cooling Code 05: Unit Control B= MicroTech III Unit Controller Code 06: Design Series (Vintage) 1= Design 1 Code 07: Voltage E= /60/1 J= 265/60/1 Code 08: Range for Entering Water/Glycol Temp. WL= Water Loop GL= Ground Loop Code 09: Return Air Location L= Left-Hand Return Air & Right-Hand Piping R= Right-Hand Return Air & Right-Hand Piping Code 10: Discharge Air Location E= End S= Straight Code 11: Fan Motor 4= ECM Constant CFM Code 12: Dehumidification Option B= Hot Gas Reheat Smart Dehumidification C= Simplified Dehumidification (Lower CFM no HGRH or no Humidistat) D= Humidistat Controlled Dehumidification (No HGRH) E= Humidistat only Code 13: Sound Packages A= Premium Code 14: IAQ Packages (Indoor Air Quality) Code 15: Coaxial Heat Exchanger Construction C= Copper Inner Tube- Steel Outer Tube S= Cupro-Nickel Inner Tube- Steel Outer Tube Code 16: Primary Air Coil Options S= Standard E= E-Coated Codes 17-18: Always YYY Code 19: Communication Module B= BACnet F= BACnet - WSHP System L= LonWorks Code 20: Filter Rack 2= 4-Sided, 2" w/duct Collar & Door 3= 4-Sided, 2" w/duct Collar, Door, Hi-Merv Seal 4= 4-Sided, 4" w/duct Collar, Door, Hi-Merv Seal Continued on next page. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 5

6 Nomenclature Code 21: Filter Type A= 2" Disposable E= Merv 8 (2" thick) Factory Installed G= Merv 13 (4" thick) Factory Installed Code 22: Water Coil- Indoor Air E= Waterside Economizer Code 23: Electric Heating- Indoor Air P= Controls for Electric Heat single 24V signal (Field installed Duct Heater by Others Code 24: Control Secondary Heat Type B= Boilerless Electric Heat E= Emergency Heat P= Primary Electric Heat (No Heat Pump Heating) S= Supplemental Heat Code 25: Desuperheater (Hot Water Generator) Code 26: Loop Pump Y Code 27: Coaxial Coil Supply Liquid Flow Control B= 2-Way, Motorized- 24V Valve Control, NO C= 2-Way, Motorized- 24V Valve Control, NC Code 28: Coaxial Coil Supply Liquid Auto Flow Reg D= 3.0 GPM E= 4.0 GPM G= 5.0 GPM Code 29: Coaxial Coil Supply Liquid Strianer Code 30: Always Y Code 31: Desuperheater Water Flow Options Codes 32-34: Always YYY Code 35: Water Coil Piping Package Option A= 3-Way, Motorized- 24V Valve Control, NO to Coax Codes 36-38: Always YYY Code 39: Primary Drain Pan Material S= Stainless Steel Code 40: Secondary Drain Pan Material Code 41: Compressor Insulation Code 42: Compressor Isolation B= Isolated Base Code 43: Insulation- Compressor Compartment S= Standard Insulation Package I= Indoor Air Quality (IAQ) Insulation Package R= Sound Reduction Package Code 44: Always Y Code 45: Insulation- Piping A= Insulated Piping Code 46: Always Y Code 47: Cabinet Finish A= Powder Coat G= Galvanized Steel Code 48: Cabinet Color T= Textured Charcoal Bronze W= Off White Code 49: Always Y Code 50: Fan Motor Control C= Various Speeds with 4 Adjustment Settings Code 51: Fan Motor Control location Code 52: Always YY Code 53: Disconnect Switch N= Non-Fused Code 54: Always Y Code 55: Control Transformer 1= 50VA 2= 75VA Code 56: Thermostat/Sensor Control S= Sensor Control T= Thermostat Control Code 57: Currrent Sensing Switches Code 58: Condensate Overflow Protection S= Sensor Code 59: High Pressure Switch A= 600 psi NC Code 60: Low Pressure Switch L= 7 psi NC Code 61: Low Temp. Protection Compressor Suction K= Thermistor 10K Code 62: Discharge Air Thermistor K= Thermistor 10K Code 63: Leaving Supply Fluid Temp K= Thermistor 10K Code 64: Entering Supply Fluid Temp K= Thermistor 10K Continued on next page. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 6

7 Nomenclature Code 65: Return Air Thermistor K= Thermistor 10K Code 66-67: Always YY Code 68: Terminal Block Connection Code 69: Emergency Switch for Electric Heat Code 70: Annunciator A= Annunciator Code 71: Reset Button Code 72: Monitoring Code 73: Emergency Stop Code 74: External Binary Output 1 Code 75: Expansion Device A= Thermal Exp. Valve Thermal Bulb & Equalizer Tube Code 76: Alarm Relay A= Alarm Relay (Dry Contacts) Code 77: Dirty Filter Sensor Code 78: Reversing Valve C= Normally Open in Cooling Mode Code 79: Outside Air Control Code 80: Always Y Code 81: Boilerless Electric Heat Setpoint GL= Glycol 28F WA= Water 55F Y Code 82: Freeze Fault Protection FF= Freeze Fault Protection Y Code 83: Occupied Setpoint Differential (1-5F) ST= Setpoint (1 F) Code 84: Unoccupied Setpoint Differential (2-10F) ST= Setpoint (2 F) Code 85: Hydronic Heating on Setpoint (70-90F) Y Code 86: BACnet Address YY Code 87: Always Y Code 88: Agency C= ETL, CETL, ARI Code 89: Conformance Code 90: Always Y Code 91: Extended Warranty Code 92: Product Style (always 1) WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 7

8 Electrical Legend Sch. Sym. AN1,2 CO1-04 Description LED Annunciator Fan Motor Capacitor C11-12 Capacitor, Compressor CP1,2 Compressor 1, 2 COE COS DAT DCS Condensate Overflow Sensor - WSE Condensate Overflow Sensor Discharge Air Temp Sensor Disconnect Switch EB1 Expansion Control Board 1 EB2 EWT FM HG HP LAT LP Exp. Control Board 2- Fan Spd CTRL Entering Water Temp Sensor Fan Motor Hot Gas Reheat Valve Actuator High Pressure Switch Leaving Air Temperature Sensor Low Pressure Switch LT1,2 Suction Line Temp Sensor 1,2 Sch. Sym. LWT M01 M11 MCB NCB OLP PL R15 R20 R25 RAT RV TR1 TR2 TR3 WSE Description Leaving Water Temp Sensor Contactor, Fan Motor Contactor, Compressor Main Control Board Network Control Board Overload Protector - Compr. Motor Loop Pump Relay, Alarm Output Relay, Loop Pump Relay, Hot Gas Reheat Return Air Temp Sensor Reversing Valve Transformer - Control Transformer - Fan Motor Transformer- Loop Pump Waterside Economizer Actuator WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 8

9 Unit Sections Front View Side View Blower Fan Assy Refrigeration Circuit Control Box Return Air Configurations Left-hand return with end discharge Left-hand return with straight discharge Right-hand return with end discharge Right-hand return with straight discharge WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 9

10 Blower Fan Assembly ECM Motor Detail 350 NP WARNING LABEL ECM Motor Nameplate Ref. No. Part Description Part Number Unit Size Blower Housing & Wheel Assy Band, Motor Mount Arm, Motor Mount ECM & Program 1 See ECM motor nameplate. 1 The PN for the ECM motor is found on the label (see illustration above). You may also contact Daikin Applied Parts Identification with the Unit Model & Serial Number to get the ECM Motor part number. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 10

11 Refrigeration Circuit Diagrams Evaporator/TXV Detail Condenser Detail Compressor Reversing Valve Piping TXV Bulb Water Temp Sensor 62 See Coremax Valve Assy Detail Compressor Mount Detail 151A 151B 151C 105 Coremax Valve Assy Detail WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 11

12 Refrigeration Circuit Components Ref. No. Description Part Number N/S Grommet, Compressor Mount N/S Hex Flange Nut, Compressor Mount N/S Sleeve, Compressor Mount WB Acorn Nut, Compressor Mount Spacer, Compressor Mount Grommet, Compressor Mount Isolation Plate, Compressor Mount Gasket, Compressor Mount Washer, Compressor Mount Nut, Compressor Mount Terminal Cover, Compressor Mount Compressor, 208/230V Compressor, 208/230V Compressor, 265V Overload Protector, Compr 208/230V Overload Protector, Compr 208/230V Overload Protector, Compr 265V COAX Coil Condenser, Copper Inner Tube COAX Coil Condenser, CUNI Inner Tube Adapter Evaporator Coil Assy N/S Reversing Valve until 4/ Reversing Valve 4/18 & later Reversing Valve until 6/ Reversing Valve 6/18 & later Solenoid, Reversing Valve until 4/ Solenoid, Reversing Valve 4/18 & later High Pressure Switch until 3/ High Pressure Switch 3/16 & later Low Pressure Switch until 9/ Low Pressure Switch 9/16 & later A Seat, Fitting B Core, Valve C Cap, Valve N/S= Not Shown. 1 Please contact Daikin Applied Parts Identification for Coil Assy, E-Coat. Continued on next page. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 12

13 Refrigeration Circuit Components, Continued Ref. No N/S Description Part Number Fusible Plug Assy Plug Only, 283 F Expansion Valve, 1T Expansion Valve, 1.5T Drain Pan Assy, SSTL- LH Drain Pan Assy, SSTL- RH N/S Gasket, Vinyl, 14.5" N/S= Not Shown. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 13

14 Hot Gas Reheat (HGRH) Ref. No. 200 Description Part Number Qty. HGRH Coil Assy, LH HGRH Coil Assy, RH Valve, Check Way Reclaim Valve until 12/ Way Reclaim Valve 12/13 & later Actuator, Reclaim Valve Please contact Daikin Applied Parts for E-Coat on coil assy. Water Flow Regulator 425 Ref. No. 425 Description Part Number Qty. Auto Flow Control Valve, 3/4" 3 GPM Auto Flow Control Valve, 3/4" 4 GPM Auto Flow Control Valve, 3/4" 5 GPM WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 14

15 Control Box MicroTech III Controls Diagrams 340 DCS M EB1 330 EB2 229 MCB AN1,AN2 320 WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 15

16 Ref. No. Description Control Box MicroTech III Controls Components Part Number Unit Size Bracket, Capacitor N/S Capacitor Boot Capacitor, 35MFD 440VAC Main Controller, MicroTech III * I/O Expansion Board Assy * LED Annunciator Assy Fan Speed Selection Board until 4/ Fan Speed Selection Board 4/14 & later Stand Off- PC Board Contactor, Compr, 2P, 30A until 12/ Contactor, Compr, 2P, 30A 12/17 & later N/S Relay, 1PDT Relay, 2PST Disconnect Switch, 10A See footnote 1. Disconnect Switch, 16A Transformer, 208/230V 50VA Transformer, 265V 50VA Transformer, 208/230V 75VA Transformer, 265/460V 75VA N/S Suction Line Temp Sensor (SLT) N/S Air Temp Sensor (DAT, RAT) N/S Water Temp Sensor (EWT, LWT) N/S= Not shown. 1 The disconnect switch depends on the unit features. Use the As-Built BOM on Parts E-Commerse, or get the specs from the installed disconnect, or contact Daikin Applied Parts Identification. * When ordering this board, please provide the software part number printed on the board s label. See control board photo on next page for label location. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 16

17 Control Box MicroTech III Controls MTIII Control Board Label Locations Label Label Label Label NOTE: When ordering the control board, please provide the software part number printed on the board s label. See above for label locations. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 17

18 Field Installed Accessories Filters and Filter Rack Description Qty. 015, 019 Filter Rack, 2" 1 Kit " Filter, Throwaway 12-Pack " Filter, Pleated, MERV 8 12-Pack " Filter, MERV 13 6-Pack MTIII Communication Module Kits Description Part Number BacNet Field Conversion Kit * LonWorks Field Conversion Kit * * Kit includes comm module card, sensors, mounting tabs, and IM. MTIII H-8 Harness Assembly Kit Description Part Number MTIII, H-8 Output Wire Harness Assembly Kit Motorized Valves Description Kit * Actuator Body 2-Way Valve Kit, Motorized, NC, 3/4" NPT Way Valve Kit, Motorized, NC, 3/4" Sweat Way Valve Kit, Motorized, NO, 3/4" NPT Way Valve Kit, Motorized, NO, 3/4" Sweat * Refer to IM 1151 for installing a motorized valve kit on MicroTech III units. Manual Valves Description Qty Part Number 2 pack Combination Shutoff/Balancing Valve with Memory Stop Ball Valve- 3/4" 10 pack WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 18

19 Description 1 For use with , , , or For use with , , , and Field Installed Accessories Continued Sensors Part Number 5.25 X 7" Adapter Plate for Sensors , , , X 5.5" Adapter Plate for Sensors , , , X 5.3" Adapter Plate for Sensors , , , Remote Sensor for Thermostat , Remote Sensor for Thermostat , Basic Room Sensor w/nsb, Override and Status LED Room Sensor, Digital Adj, 4-Button w/ Override, Occupancy Switch & Temp Display Room Sensor w/cool/warm Temp Adj. & Occupancy Switch Room Sensor, Digitally Adj, Temp & Humidity Display Wall Sensor, Adj. Cool/Warm, Occupancy Switch Trim Ring for Sensors , , or Indoor Sensor for Outdoor Sensor for Wall Plate for Remote TStat, Insulated Wall Plate for Remote TStat Thermostats Description Part Number Programmable Touch-Screen TStat Wall Stat: AC/DC, ACO, 7-day Programmable, 2 Heat/2 Cool with Wall Plate Wall Stat: AC/DC, ACO, Non- Programmable, 2 Heat/2 Cool, NSB & OR with Wall Plate TStat Non-Programmable- 2 Heat/2 Cool, ACO & MCO TStat Programmable- 2 Heat/2 Cool, ACO & MCO and 7-day TStat Programmable/Non-Programmable- 2 Heat/2 Cool, ACO, Touchscreen, WIFI TStat Programmable/Non-Programmable- 2 Heat/3 Cool, ACO, Touchscreen TStat Programmable/Non-Programmable- 2 Heat/2 Cool, ACO, Touchscreen, WIFI TStat Programmable/Non-Programmable- 2 Heat/3 Cool, ACO, Touchscreen TStat Guards Description Qty Part Number TStat Guard Each TStat Guard 10- Pack WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 19

20 Description Field Installed Accessories Continued Loop Pump Modules Part Number Hose Kit, 1.0" x 12 ft. Hose, 1/2" Fittings Hose Kit, 1.0" x 12 ft. Hose, 3/4" Fittings Hose Kit, 1.0" x 12 ft. Hose, 1.0" Fittings Hose Kit, 1.0" x 12 ft. Hose, No Fittings Single Pump, Geothermal Loop- Cast Iron Single Pump, Geothermal Loop- Bronze Dual Pump, Geothermal Loop- Cast Iron Dual Pump, Geothermal Loop- Bronze Relay Pump Kit Waterside Economizer Description RH LH 3-Way Valve, Motorized, 3/4" Sweat Actuator Motor, NC, 24V WSE Coil Assy until 03/ WSE Coil Assy 03/15 & later Unit Hanger Description Part Number Unit Hanger Kit Kit includes four (4) brackets (p/n ), four (4) grommets (p/n ), and hardware. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 20

21 Field Installed Accessories Continued Hoses Description Specification 2 Foot 3 Foot Hose Kit, Fire Rated Condensate 3/ Hose Kit, Plastic Condensate 3/ Hose Kit, Fire Rated Supply/Return (2 Pack) 3/ Auto Flow Supply and Return w/ball Valves Flow Control Hose Kit, Fire Rated Supply/Return- 3/4" Includes: Supply Line: Ball valve with one port and a 24" stainless steel hose with swivel. Return Line: Combination flow controller & ball valve with two ports and a 24" stainless steel hose with swivel. Auto Flow Supply and Return w/ball Valves and Strainer Flow Control Hose Kit, Fire Rated Supply/Return- 3/4" Includes: Supply Line: Combination ball valve & y-strainer, blow down valve, with one port and a 24" stainless steel hose with swivel. Return Line: Combination flow controller & ball valve with two ports and a 24" stainless steel hose with swivel. 3.0 GPM N/A 3.5 GPM N/A 4.0 GPM N/A 4.5 GPM N/A 5.0 GPM N/A 6.0 GPM N/A 3.0 GPM GPM GPM GPM GPM GPM Hose Kit Supply and Return w/ball Valves 3/ Hose Kit Supply and Return w/ball Valves and Strainer 3/ Hose Kit Jumper Hose Kit w/90 Adapter 3/4" x 4 Ft N/A = Not Applicable. Note: Refer to IM 1226 for Daikin Fire Rated Hoses & Hose Kits and for installation instructions. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 21

22 Part Number Kit Field Installed Accessories Continued MicroTech III Temperature Sensors Tennant Override Setpoint Adjustment Status LED Note: Can only be used in conjunction with a communication (Comm.) card. See OM 931 for required jumper settings. Fan & Mode Switch Yes No No No Yes 55 to 95 F (12 to 35 C) Yes Yes Yes -3 to +3 F (-1.5 to 1.5 C) No Yes Description * IM is included in Kit. ** Kit components listed below. Microtech III Unit Control Accessories ** Multiple Unit Control Panel: Allows a master unit controlled by a single thermostat, to operate up to 3 secondary units. Not Recommended for use with a Boilerless System Kit. Part Number Boilerless System Kit with I/O Expansion Board * Boilerless System Kit without I/O Expansion Board Multiple Unit Control Panel Kit Ref. Part Description Qty. No. Number 310 Cover, Control Box Circuit Board Stand Off, Circuit Board Box WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL / Page 22

23 Critical Daikin Applied OEM Parts Are What Your HVAC Unit Needs! Daikin SmartSource Single Stage WSHP Daikin McQuay SmartSource Single Stage WSHP WGSH 015, 019 Design 1 Critical Components Unit Sizes Voltage Part Number Control Control Board, MicroTech III ALL ALL Compressor Compressor /60/ Compressor /60/ Compressor /60/ Compressor /60/ Blower Motor ECM & Program ALL ALL See motor nameplate Blower Fan Assembly Blower Housing & Wheel Assy ALL N/A Sensor Line Temp Sensor (SLTS) ALL N/A Air Temp Sensor (DAT, RAT) ALL N/A Water Temp Sensor (EWT, LWT) ALL N/A Call Your Local Daikin Applied Parts Distributor For All Your Parts Needs. To Locate A Distributor, Go To or Call PARTS Rev. N 10/2018 CPL Page 1 of 1