2c 15A, 4c 10A polarized power relays

Transcription

1 c 5A, 4c A polarized power relays SP RELAYS RoHS compliant Protective construction: Dust cover type Taking advantage of the 4-gap balanced armature mechanism, S relays have met a number of relay needs and earned a reputation for the characteristics that they provide. Building on the same structure, the SP relay was introduced as a highsensitivity power relay to provide nominal operating power of 3 mw and minimum operating power of 5 mw (single side stable and coil latching types). Even so, with the nominal switching capacity for the Form C at 5 A, and for the 4 Form C at A, highcapacity switching is possible with small input. Moreover, taking full advantage of the ecellence of the 4-gap balanced armature mechanism, we have realized a small, slim form factor that also has superior resistance to vibration and shock. This power relay is often chosen for NC machines and electrical power remote monitoring control panels, and for power supplies used in computers and other equipment. The SP also often provides power control for high-end business and industrial equipment. FEATURES. Small, slim form factor Facilitating the form factor reduction of devices, the overall height of the relay package is less than half that of our HP relay.. High sensitivity The high-efficiency polarized electromagnetic mechanism in conjunction with our eclusive spring alignment method achieves levels of sensitivity higher than relays that have been available up to now. For both the Form C and 4 Form C single side stable and coil latching types, the 5 mw minimum operating power level allows direct driving by transistor or chip controllers. 3. High reliability and long life With a structure that ensures almost perfectly complete twin contact and minimal contact bounce, you get greater reliability than has so far been provided by power relays. 4. Latching types also available coil latching and coil latching types are available. In cases where it was formerly unavoidable to use plural relays for large power memory, you can now use a single SP relay. 5. Strong resistance to vibration and shock Our balanced armature technology well withstands vibration and shocks. It provides strong resistance to vibration and shock. 6. Terminals and mounting boards are available ASCTB8E 56-T

2 ORDERING INFORMATION Contact arrangement : Form C 4: 4 Form C Terminal shape Nil: Plug-in type P: PC board type Operating function Nil: Single side stable L: coil latching L: coil latching Nominal coil voltage 3, 5, 6,, 4, 48 V DC SP Notes:. PC board type and coil latching type are manufactured by lot upon receipt of order.. Certified by UL, CSA and TÜV TYPES Contact arrangement Form C 4 Form C Nominal coil voltage Single side stable Standard packing ( Form C): Carton: pcs.; Case: pcs. Standard packing (4 Form C): Carton: pcs.; Case: pcs. Note: PC board type and coil latching type are manufactured by lot upon receipt of order. * Terminal sockets and mounting boards available. coil latching 3V DC SP-DC3V SP-L-DC3V 5V DC SP-DC5V SP-L-DC5V 6V DC SP-DC6V SP-L-DC6V V DC SP-DCV SP-L-DCV 4V DC SP-DC4V SP-L-DC4V 48V DC SP-DC48V SP-L-DC48V 3V DC SP4-DC3V SP4-L-DC3V 5V DC SP4-DC5V SP4-L-DC5V 6V DC SP4-DC6V SP4-L-DC6V V DC SP4-DCV SP4-L-DCV 4V DC SP4-DC4V SP4-L-DC4V 48V DC SP4-DC48V SP4-L-DC48V RATING. Coil data ) Single side stable Nominal coil voltage 3V DC ) coil latching Pick-up voltage (at C 68 F) Drop-out voltage (at C 68 F) current [±%] (at C 68 F) Coil resistance [±%] (at C 68 F) ma 3Ω 5V DC 6.mA 83Ω 6V DC 7%V or less of %V or more of 5mA Ω nominal voltage nominal voltage V DC (Initial) (Initial) 5mA 48Ω 4V DC.5mA,9Ω 48V DC 6.mA 7,7Ω Nominal coil voltage Set voltage (at C 68 F) Reset voltage (at C 68 F) current [±%] (at C 68 F) Coil resistance [±%] (at C 68 F) power 3mW power Set coil Reset coil Set coil Reset coil Set coil Reset coil 3V DC ma ma 3Ω 3Ω 5V DC 6.mA 6.mA 83Ω 83Ω 6V DC 7%V or less of 7%V or less of 5mA 5mA Ω Ω nominal voltage nominal voltage V DC (Initial) (Initial) 5mA 5mA 48Ω 48Ω 3mW 3mW 4V DC.5mA.5mA,9Ω,9Ω 48V DC 6.mA 6.mA 7,68Ω 7,68Ω Ma. applied voltage 5%V of nominal voltage Ma. applied voltage 5%V of nominal voltage ASCTB8E 56-T

3 . Specifications Characteristics Item Specifications Contact Rating Electrical characteristics Mechanical characteristics Epected life Conditions Unit weight Initial contact pressure Form C: Appro..39 N (4 g.4 oz), 4 Form C: Appro..96 N ( g.7 oz) Arrangement Form C, 4 Form C Contact resistance (Initial) Ma. 3 mω (By voltage drop 6 V DC A) Contact material Stationary contact: Au flashed AgSnO type, Movable contact: AgSnO type Nominal switching capacity (resistive load) Form C: 5 A 5 V AC, 4 Form C: A 5 V AC Ma. switching power (resistive load) Form C: 3,75 VA, 3 W, 4 Form C:,5 VA, 3 W Ma. switching voltage Form C, 4 Form C: 5 V AC, 3 V DC (48V DC: Ma. A) Ma. switching current Form C: 5 A (AC) A (DC), 4 Form C: A power 3mW (Single side stable, coil latching) switching capacity (reference value)* ma 5V DC Insulation resistance (Initial) (5 C, 5% relative humidity) Breakdown voltage (Initial) Between open contacts Between contact and coil Between contact sets Operate time [Set time] (at C 68 F) Release time [Reset time] (at C 68 F) Temperature rise (coil) (at C 68 F) Shock resistance Vibration resistance Mechanical Electrical (resistive load) Functional Destructive,MΩ (at 5V DC) Measurement at same location as Breakdown voltage section.,5 Vrms for min. (Detection current: ma) 3, Vrms for min. (Detection current: ma) 3, Vrms for min. (Detection current: ma) Ma. 3 ms [Ma. 3 ms] (Nominal coil voltage applied to the coil, ecluding contact bounce time.) Ma. ms [Ma. 3 ms] (Nominal coil voltage applied to the coil, ecluding contact bounce time.) (without diode) Ma. 4 C (By resistive method, nominal voltage applied to the coil; nominal switching capacity.) 39 m/s (Half-wave pulse of sine wave: ms; detection time: μs.) 98 m/s (Half-wave pulse of sine wave: 6 ms.) Functional to 55 Hz at double amplitude of 3 mm (Detection time: μs.) Destructive to 55 Hz at double amplitude of 3 mm Conditions for operation, transport and storage* Ma. operating speed 5 7 (at 8 times/min.) Form C: 5 (5 A 5 V AC [at times/min.]), 5 ( A 3 V DC [at times/min.]) 4 Form C: 5 (5 A 5 V AC [at times/min.]), 5 ( A 3 V DC [at times/min.]) Ambient temperature: 5 C to +6 C 58 F to +4 F; Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature) times/min. (at rated load) Form C: 5 g.76 oz; 4 Form C: 65 g.9 oz Notes: *. This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load. *. The upper limit of the ambient temperature is the maimum temperature that can satisfy the coil temperature rise value. Refer to Usage, transport and storage conditions in NOTES. SP REFERENCE DATA.-() Coil temperature rise ( Form C type) Tested sample: SP-DC4V 5.-() Coil temperature rise (4 Form C type) Tested sample: SP4-DC4V Ambient temperature: 7 to 9 C 8 to 84 F 5 Temperature rise, C A A 5 A A Temperature rise, C 4 3 A 5 A A Coil applied voltage, V Coil applied voltage, V 3 ASCTB8E 56-T

4 . Electrical life (SP, 5 A 5 V AC resistive load) Change of pick-up and drop-out voltage Change of contact resistance Pick-up/drop-out voltage, V 5 5 Pick-up voltage Drop-out voltage Ma. Ma. Contact resistance, mω 5 5 N.C. N.O. Ma. Ma No. of operations, 4 No. of operations, 4 3. Electrical life (SP4, A 5 V AC resistive load) Change of pick-up and drop-out voltage Change of contact resistance Pick-up/drop-out voltage, V 5 5 Pick-up voltage Drop-out voltage No. of operations, 4 Ma. Ma. Contact resistance, mω No. of operations, 4 N.C. N.O. Ma. DIMENSIONS (mm inch) Form C ) Plug-in terminal CAD Data Eternal dimensions FASTON #87 The CAD data of the products with a CAD Data mark can be downloaded from: ) PC board type CAD Data Eternal dimensions General tolerance: ±.3 ±. PC board pattern (Bottom view) dia dia. Schematic (Bottom view) Single side stable type (Deenergized condition) coil latching type 8 9 SET 8 9 RST 3 4 (Reset condition) General tolerance: ±.3 ± Tolerance: ±. ±.4 Diagram shows the reset position when terminals 3 and 4 are energized. Energize terminals and to transfer contacts. 4 ASCTB8E 56-T

5 4 Form C ) Plug-in terminal CAD Data Eternal dimensions General tolerance: ±.3 ±. ) PC board type CAD Data Eternal dimensions General tolerance: ±.3 ±. PC board pattern (Bottom view) dia dia. Tolerance: ±. ±.4 Schematic (Bottom view) Single side stable type (Deenergized condition) coil latching type 8 9 SET RST 3 4 (Reset condition) Diagram shows the reset position when terminals 3 and 4 are energized. Energize terminals and to transfer contacts. SAFETY STANDARDS Form C 4 Form C Item UL (Recognized) CSA (Certified) TÜV (Certified) File No. Contact rating File No. Contact rating File No. Rating E438 E438 5A 5V AC /HP 5, 5V AC A 3V DC A 5V AC /3HP 5, 5V AC A 3V DC LR655 LR655 5A 5V AC /HP 5, 5V AC A 3V DC A 5V AC /3HP 5, 5V AC A 3V DC B B A 5V AC (cosφ=.) A 3V DC A 5V AC (cosφ=.) A 3V DC NOTES. For cautions for use, please read GENERAL APPLICATION GUIDELINES on page B-. 5 ASCTB8E 56-T

6 Automation Controls Catalog ACCESSORIES TYPES Product name SP Terminal socket SP4 Terminal socket SP RELAYS TERMINAL SOCKETS SP-SF SP4-SF DIMENSIONS (mm inch) SP Terminal socket CAD Data The CAD data of the products with a CAD Data mark can be downloaded from: SP4 Terminal socket CAD Data 4.64±.4 3± 9.5±.6 3± ±.4 3±.6 3±.6.6±.6.96± ±.4.8±.4.6±.6.6±.4.8±.4.3±.4.3±.4.8±.6 4.5±.4.8±.6 3± 9.5±.6 4.5±.3.77±.6.96± ±.4.77±. 7.5±.776± ±.4.56± ±.4 67± 5.4±.4.±.6 6.5±.3.638±.39.6±.6.56±. 97± 5.4± ±.39.6±.6 : SP-SF 4.5±.6.594±.4 5±.47±.39 ±.4 ±.4.433±.6.87±.6 : SP4-SF 5±.47±.39 Note: Terminal number marking is on the socket body. Please refer together with the SP relay schematic. General tolerance: ±.5 ±. Mounting hole diagram 3±. -4.5±. dia. hole.8± ±.4 dia. hole Notes: () Mounting screws and the fastening bracket are included in the package. () Mount the relay with the proper mounting direction i.e. with the direction of the mark on top of the relay case matching the direction of the mark on the terminal block. (The direction of the terminal block is the upward direction of the relay.) Fastening bracket mounting and removal. Mounting Insert the A part of the fastening bracket into the mounting groove of the terminal block, and then fit the B part into groove, while pressing with the tip of a minus screwdriver.. Removal Slide the B part of the fastening bracket from the groove in the terminal block, while pressing with the tip of a minus screwdriver. While the bracket is in this position, keep pressing the C part of the bracket to the relay side with your finger, and lift up to the left side and remove from the groove, as in the diagram at right. Minus screwdriver C Fastening bracket B SP relay A Terminal block 4. industrial.panasonic.com/ac/e/ Panasonic Corporation 4 ASCTB9E 4-T

7 ACCESSORIES TYPES Product name Mounting board SP RELAYS MOUNTING BOARD SP-MA Direct chassis mounting possible, and applicable to DIN rail. DIMENSIONS (mm inch) CAD Data The CAD data of the products with a CAD Data mark can be downloaded from: Mounting hole diagram dia. hole dia. hole Panel cutout Tolerance: ±. ±.4 Use method. Both the SP relay Form C and 4 Form C can be mounted to the mounting slats.. Use the mounting slats either by attaching them directly to the chassis, or by mounting with a DIN rail. ) When attaching directly to chassis Use two M3 screws. For the mounting pitch, refer to the specification diagram. ) When mounting on a DIN rail Use a 35mm.378inch wide DIN rail (DIN4677). The mounting method should be as indicated in the diagram at right. Method for mounting on DIN rail Fig. Fig. Press Fit into mounting grooves. Fig. 3 Fit in Press relay in Mounting slat DIN rail To remove the relay, press down the mounting slats so the claws move to the outside. () First fit the arc shaped claw of the mounting slat into the DIN rail. () Press on the side as shown in the diagram below. (3) Fit in the claw part on the opposite side. Precautions for use When mounting to a DIN rail, use a commercially available fastening bracket if there is a need to stop sliding of the mounting slat in the rail direction. Panasonic Corporation Automation Controls Business Division industrial.panasonic.com/ac/e/ Panasonic Corporation 4 ASCTB9E 4-T