Description. Rhino SD2/XD2 Follower Modules

Transcription

1 Rhino SD/XD Follower Modules Description See Figure. The follower module attaches onto the hydraulic section of the pump (). It is designed to force material out of straight-sided containers. Standard and PTFE-coated follower plate modules are available to fit the following container inner diameters: 0-mm -mm (-gal US Standard) 0-mm 0-mm -mm (0-gal US Standard) -mm (-gal US Standard) NOTE: PTFE-coated follower plate modules are used on stainless steel pumps when an application requires the use of reactive materials. Depending upon the module, follower plates () have either one or two rubber seals. When the follower plate is lowered into a container, the rubber seals cause the material to pressurize by creating a tight seal around the inner diameter of the container. When the pump cycles, the follower plate forces the material out of the container and into the pump hydrualic section. The rubber seals also protect the material from moisture and contamination from the surrounding environment. A PTFE-coated steel ring () is used along with a standard follower plate module for high-viscosity urethane materials that are shipped in foil bags. It is sized for a close-tolerance fit to the inner diameter of the container. The ring collapses the foil bag to prevent it from getting wedged between the follower plate module and the container wall. Lowering the follower plate module into a container will cause air buildup between the bottom of the follower plate () and the material. Removing the bleeder stem () from the adapter () before lowering the follower plate provides a path for the air to vent. NOTE: The additional NPT port on the bleeder stem adapter for th back to the container. The additional NPT port foe -mm and -mm follower plate modules is used to connect an optional depressurization circuit that vents material connecting a depressurization circuit on 0-mm, -mm, 0-mm, and 0-mm follower plate modules is located on the follower plate. The blow-off tube () allows air to enter the area below the follower plate. When the elevator is in the Up position and the blow-off valve is opened, air flows under the follower plate. This pressure forces the container off of the follower plate. GAL ( MM) 0 GAL ( MM) GAL ( MM) Figure Follower Modules. Blow-off tube. Bleeder stem. Follower plate module. Bleeder stem adapter. Pump (partial pump hydraulic section shown). PTFE-coated steel ring 0 Nordson Corporation Part 0-0

2 Rhino SD/XD Follower Modules Replacing the Follower Plate Seals Read and understand this procedure before replacing the follower plate seals. Contact a local Nordson representative if you have questions regarding this procedure. WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. NOTE: Although the -gal unloader is shown, this procedure is typical for a -gal unloader with the exception of the follower seal quantities. The -gal unloader has one follower seal. If the material container needs to be removed from the unloader, it is important to remember that the Neutral setting on the elevator control valve is not a locked and secured position. Table lists the items that are required to perform this procedure: Item Support blocks Two large screwdrivers or pry bars O-ring grease Table Required Items Use Prevents air cylinder pistons from drifting downward during repairs Pries follower plate seals off of the follower plate NOTE: Follower plate seals are removed in the same manner as a tire from a rim Lubricates new follower plate seals. If installed, remove the material container from the unloader.. See Figure. Insert the support blocks (). -gal Unloaders: Insert support blocks () between the frame cross bar () and the top of both air cylinders (). -gal Unloaders: Insert support blocks () between the lower air motor cap () and the top of both air cylinders ().. Use either large screwdrivers or pry bars to pry the follower plate seals () off of the follower plate grooves ().. Perform the following: a. All Unloaders: Clean the follower plate grooves and remove all foreign material. b. -gal Unloaders: Inspect the neoprene bands () on the -gal follower plate () for damage and replace if necessary.. Install the new follower plate seals () using either large screwdrivers or pry bars.. Apply a compatible O-ring grease to the follower plate seals ().. Remove the support blocks () from the unloader. Put the unloader back into service if desired. NOTE: The O-ring grease must be compatible with material being pumped and the new follower plate seals Part Nordson Corporation

3 Rhino SD/XD Follower Modules -GAL UNLOADER -GAL UNLOADER -GAL UNLOADER NEOPRENE BANDS Figure Replacing the Seals 0 Nordson Corporation Part 0-0

4 Rhino SD/XD Follower Modules Parts To order parts, call the Nordson Customer Service Center or your local Nordson representative. -Gal Follower Modules for. Cu-In. Pumps See Figure and refer to the following parts list. NOTE: These follower modules are designed to fit the following container inner diameters: 0 mm mm (-gal US Standard) mm TFE (-gal US Standard) 0 mm 0 mm 0 Figure -Gal Follower Modules for. Cu-In. Pumps Part Nordson Corporation

5 Rhino SD/XD Follower Modules Item Part Description Qua Note 000 FOLLOWER PLATE MODULE, 0 mm,. throat,. cu-in. pump 000 FOLLOWER PLATE MODULE, mm,. throat,. cu-in. pump A 000 FOLLOWER PLATE MODULE, mm TFE,. throat,. cu-in. pump A 000 FOLLOWER PLATE MODULE, 0 mm,. throat,. cu-in. pump 000 FOLLOWER PLATE MODULE, 0 mm,. throat,. cu-in. pump 0 mm: SEAL, molded mm and mm TFE: SEAL, molded A 0 mm: SEAL, steam hose 0 mm: SEAL, steam hose 00 0 mm: FOLLOWER PLATE 00 mm: FOLLOWER PLATE 00 mm TFE: FOLLOWER PLATE 00 0 mm: FOLLOWER PLATE 00 0 mm: FOLLOWER PLATE NUT, hex regular, /-0 0 WASHER, lock / 0 WASHER, flat, 0.0 x 0. x NIPPLE, pipe, schedule 0, / NPT, in. 0 mm TFE: NIPPLE, pipe, schedule 0, / NPT, in. stainless steel 0 O-RING, Viton,. x. x 0.0 SCREW, hex, /- x. 0 VALVE, ball, / NPT 0 0 CONNECTOR, male, /-0 x / NPT 00 STEM ASSEMBLY, bleed, gal 0 mm TFE: STEM ASSEMBLY, bleed, -gal, stainless steel 00 ADAPTER, female, / x / NPT PLUG, pipe, socket, / 0 mm TFE: PLUG, pipe, socket, /, stainless steel 00 ADHESIVE, Loctite Threadlocker Red AR 00 ADHESIVE, sealant PST AR 00 LUBRICANT, Never-Seez, -oz. can NOTE A: -gal US Standard 0 Nordson Corporation Part 0-0

6 Rhino SD/XD Follower Modules -Gal Follower Modules for. Cu-In. Pumps See Figure and refer to the following parts list. NOTE: These follower modules are designed to fit the following container inner diameters: 0 mm mm (-gal US Standard) mm TFE (-gal US Standard) 0 mm 0 mm 0 Figure -Gal Follower Modules for. Cu-In. Pumps Part Nordson Corporation

7 Rhino SD/XD Follower Modules Item Part Description Qua Note 00 FOLLOWER PLATE MODULE, 0 mm,. throat,. cu-in. pump 00 FOLLOWER PLATE MODULE, mm,. throat,. cu-in. pump A 0 FOLLOWER PLATE MODULE, mm TFE,. throat,. cu-in. pump A 00 FOLLOWER PLATE MODULE, 0 mm,. throat,. cu-in. pump 0 FOLLOWER PLATE MODULE, 0 mm,. throat,. cu-in. pump 0 mm: SEAL, molded mm and mm TFE: SEAL, molded A 0 mm: SEAL, steam hose 0 mm: SEAL, steam hose 0 0 mm: FOLLOWER PLATE mm: FOLLOWER PLATE 0 mm TFE: FOLLOWER PLATE 0 0 mm: FOLLOWER PLATE 0 mm: FOLLOWER PLATE NUT, hex regular, /- 0 WASHER, lock / 0 WASHER, flat, 0.0 x 0. x NIPPLE, pipe, schedule 0, / NPT, in. 0 mm TFE: NIPPLE, pipe, schedule 0, / NPT, in. stainless steel 0 GASKET, follower SCREW, hex, /- x. 0 VALVE, ball, / NPT 0 0 CONNECTOR, male, /-0 x / NPT 00 STEM ASSEMBLY, bleed, gal 0 mm TFE: STEM ASSEMBLY, bleed, gal, stainless steel 00 ADAPTER, female, / x / NPT PLUG, pipe, socket, / 0 mm TFE: PLUG, pipe, socket, /, stainless steel 00 ADHESIVE, Loctite Threadlocker Red AR 00 ADHESIVE, sealant PST AR 00 LUBRICANT, Never-Seez, -oz. can NOTE A: -gal US Standard 0 Nordson Corporation Part 0-0

8 Rhino SD/XD Follower Modules 0-Gal Follower Modules for. and. Cu-In. Pumps See Figure and refer to the following parts list. 0 Figure 0-Gal Follower Modules for. and. Cu-In. Pumps Item Part Description Qua Note 000 FOLLOWER PLATE MODULE,. cu-in. pump,. throat A 0 FOLLOWER PLATE MODULE,. cu-in. pump,. throat A 00. cu-in. pump: FOLLOWER PLATE,. throat 0. cu-in. pump: FOLLOWER PLATE,. throat 0. cu-in. pump: O-RING, Viton,. x. x 0.0,. throat 00. cu-in. pump: O-RING, Viton, x. x 0.0,. throat 0 NIPPLE, pipe, schedule 0, / NPT, in. 0 WASHER, lock, M0 SCREW, socket, M0 x 0 0 VALVE, ball, / NPT 0 CONNECTOR, male, /-0 x / NPT 00 STEM ASSEMBLY, 0-gal PLUG, pipe, socket, / 0 TEE, street, / NPT SEAL, follower, 0 gal 00 ADHESIVE, Loctite Threadlocker Red AR 00 ADHESIVE, sealant, PST AR 00 LUBRICANT, Never-Seez, -oz can LUBRICANT, O-ring, Parker, oz NOTE A: Items and are specific to each follower plate module. Items through are common to all follower plate modules. Part Nordson Corporation

9 Rhino SD/XD Follower Modules -Gal Follower Modules for. Cu-In. Pumps See Figure and refer to the following parts list. 0 Figure -Gal Follower Modules for. Cu-In. Pumps Item Part Description Qua Note 00 FOLLOWER PLATE MODULE, standard, gal,. throat A 000 FOLLOWER PLATE MODULE, PTFE-coated, gal,. throat A 00 Standard: FOLLOWER PLATE 00 PTFE-coated: FOLLOWER PLATE 0 Standard: NIPPLE, pipe, schedule 0, / NPT, in., galvanized PTFE-coated: NIPPLE, pipe, schedule 0, / NPT, in., 0 stainless steel 0 Standard: STEM, bleeder 0 PTFE-coated: STEM, bleeder, stainless steel Standard: PLUG, pipe, socket, / 0 PTFE-coated: PLUG, pipe, socket, /, stainless steel Standard: TEE, / NPT 0 PTFE-coated: TEE, / NPT, stainless steel 0 O-RING, Viton,. x. x WASHER, lock, M0 SCREW, socket, M0 x 0 0 VALVE, ball, / NPT 0 CONNECTOR, male degrees, /- x / 0 RING, neoprene, follower 0 SEAL, follower 00 ADHESIVE, Loctite Threadlocker Red AR 00 ADHESIVE, sealant, PST AR 00 LUBRICANT, Never-Seez, -oz can LUBRICANT, O-ring, Parker, oz NOTE A: Items through are specific to each follower plate module. Items through are common to all follower plate modules. 0 Nordson Corporation Part 0-0

10 0 Rhino SD/XD Follower Modules -Gal Follower Module for. Cu-In. CE Pumps See Figure and refer to the following parts list. 0 Figure -Gal Follower Module for. Cu-In. CE Pump Item Part Description Qua 00 FOLLOWER PLATE MODULE, standard, gal,. throat FOLLOWER PLATE 0 NIPPLE, pipe, schedule 0, / NPT, in., galvanized 0 STEM, bleeder PLUG, pipe, socket, / TEE, / NPT 00 O-RING, Viton, x. x WASHER, lock, M0 0 SCREW, socket, M0 x 0 VALVE, ball, / NPT 0 CONNECTOR, male deg, /- x / 0 RING, neoprene, follower 0 SEAL, follower 00 ADHESIVE, Loctite AR 00 ADHESIVE, sealant, PST AR 00 LUBRICANT, Never-Seez, -oz can LUBRICANT, O-ring, Parker, oz 0 ADAPTER, follower,. ID 0 GASKET, follower Note Part Nordson Corporation

11 Rhino SD/XD Follower Modules -Gal Follower Modules for. Cu-In. Pumps See Figure and refer to the following parts list. 0 Figure -Gal Follower Modules for. Cu-In. Pumps Item Part Description Qua Note 0 FOLLOWER PLATE MODULE, standard, gal,. throat A 0 FOLLOWER PLATE MODULE, PTFE-coated, gal,. throat A 0 Standard: FOLLOWER PLATE 0 PTFE-coated: FOLLOWER PLATE 0 Standard: NIPPLE, pipe, schedule 0, / NPT, in., galvanized PTFE-coated: NIPPLE, pipe, schedule 0, / NPT, in., stainless 0 steel 0 Standard: STEM, bleeder 0 PTFE-coated: STEM, bleeder, stainless steel Standard: PLUG, pipe, socket, / 0 PTFE-coated: PLUG, pipe, socket, /, stainless steel Standard: TEE, / NPT 0 PTFE-coated: TEE, / NPT, stainless steel 00 O-RING, Viton, x. x WASHER, lock, M0 SCREW, socket, M0 x 0 0 VALVE, ball, / NPT 0 CONNECTOR, male deg, /- x / 0 RING, neoprene, follower 0 SEAL, follower 00 ADHESIVE, Loctite Threadlocker Red AR 00 ADHESIVE, sealant, PST AR 00 LUBRICANT, Never Seez, -oz can LUBRICANT, O-ring, Parker, oz NOTE A: Items through are specific to each follower plate module. Items through are common to all follower plate modules. 0 Nordson Corporation Part 0-0

12 Rhino SD/XD Follower Modules -Gal Follower Modules with Steel Ring for. and. Cu-In. Pumps See Figure and refer to the following parts list. 0 Figure -Gal Follower Modules with Steel Ring for. and. Cu-In. Pumps Item Part Description Qua Note 0000 FOLLOWER PLATE MODULE, w/ ring,. cu-in. pump, gal,. throat A FOLLOWER PLATE MODULE, w/ ring,. cu-in. pump, gal,. throat, UHMW, polyethylene A 0 FOLLOWER PLATE MODULE, w/ ring,. cu-in. pump, gal,. throat A 00. cu-in. pump: FOLLOWER PLATE 0. cu-in. pump: FOLLOWER PLATE 0. cu-in. pump: O-RING, Viton,. x. x cu-in. pump: O-RING, Viton, x. x NIPPLE, pipe, schedule 0, / NPT, in., galvanized 0 WASHER, lock, M0 SCREW, socket, M0 x 0 0 VALVE, ball, / NPT CONNECTOR, male deg, /- x / 0 STEM, bleeder Standard: PLUG, pipe, socket, / 0 TEE, / NPT./. cu-in. pump: RING, mm 0. cu-in. UHMW PE pump: RING, platen, gal, XDH, UHMW, PE 00 ADHESIVE, Loctite Threadlocker Red AR 00 ADHESIVE, sealant, PST AR 00 LUBRICANT, Never-Seez, -oz can LUBRICANT, O-ring, Parker, oz NOTE A: Items and are specific to each follower plate module. Items through are common to all follower plate modules. Part Nordson Corporation

13 Rhino SD/XD Follower Modules -Gal Follower Modules with Grid Plate for. and. Cu-In. Pumps See Figure 0 and refer to the following parts list Figure 0 -Gal Follower Modules with Grid Plate for. and. Cu-In. Pumps 0 Nordson Corporation Part 0-0

14 Rhino SD/XD Follower Modules Item Part Description Qua Note 00 FOLLOWER PLATE MODULE, w/ grid plate,. cu-in. Pump, gal,. throat A 0 FOLLOWER PLATE MODULE, w/ grid plate,. cu-in. pump, gal,. throat A 00 RETAINER, grid plate, gal 00 SEAL, follower, gal, one piece 0 RING, neoprene, follower 00. cu-in. pump: PLATE, follower, gal,. in. throat, SD 0. cu-in. pump: PLATE, follower, gal,. in. throat 0. cu-in. pump: O-RING, Viton,.0 x 0. x cu-in. pump: O-RING, Viton,.0 x. x WASHER, lock, M0, steel, zinc SCREW, socket, M0 x 0, blue 0 NIPPLE, pipe, schedule 0, ½ NPT, in., galvanized 0 VALVE, ball, ½ NPT 0 CONNECTOR, male,, / x ½, steel 0 STEM, bleeder, follower, long PLUG, pipe, socket, standard, ½, zinc TEE, street, S, ½ NPT 00 NIPPLE, follower, hex, ½ NPT x deg cut, stainless steel SCREW, button, socket, ¼ 0 x 0.00, blue 00 LUBRICANT, Never-Seez, -oz can AR LUBRICANT, O-ring, Parker, oz 00 ADHESIVE, sealant, PST AR 00 ADHESIVE, Loctite Threadlocker Red AR 0 00 ADHESIVE, Loctite Threadlocker Blue, removable, 0 m NOTE A: Items and are specific to each follower plate module. The remaining items are common to all follower plate modules. Issued / Original copyright date 00. Rhino, Nordson, and the Nordson logo are registered trademarks of Nordson Corporation. All other trademarks are the property of their respective owners. Part Nordson Corporation