|
|
|
- Avice Richard
- 5 years ago
- Views:
Transcription
1 Page 1 of 10 SECTION : Automatic Transaxle/Transmission 2005 Focus Workshop Manual ASSEMBLY Procedure revision date: 04/04/2008 Transaxle Printable View (2476 KB) Special Tool(s) Alignment Tool, Transmission Range Sensor Handle, Torque Converter (T81P-7902-C) Installer, Differential Bearing Cup (T77F-4222-A) Installer, Differential Fluid Seal (T92P FH) Select Gauge, Transmission Band Shim Gauge, Differential/Transfer Gear Bearing Adapter for (Handle) (T80T-4000-W) Holding Tool, Final Drive Input Gear Mounting Bracket, Transmission Installer, Drive Pinion Bearing Cup (T67P-4616-A) Installer, Transfer Gear Bearing Cup Shim Selection Set (T88C JF) Socket, Final Drive Input Nut
2 Page 2 of 10 Shim Selection Set (T88C C) Wrench Guide Plate Retainer, Torque Converter (T97T-7902-A) Material Motorcraft TA-29 Thread Sealer Item Specification WSS-M4G-323-A3 WSK-M2G350-A2 Assembly 1. Using the special tool, install the final drive input gear bearing. 1. Install the final drive input gear bearing. 2. Install the special tool. 2. Using an arbor press and the special tools, seat the final drive input gear bearing. 3. Install a new collapsible spacer. 4. Using the special tool, position the final drive input gear.
3 Page 3 of NOTICE: Hold the final drive input gear while installing the final drive input gear bearing to prevent it from falling out of the transaxle case. Rotate the transaxle 180 degrees. 6. Using the special tools, install the final drive input gear bearing. 7. Rotate the transaxle 180 degrees. 8. Using the special tool, lock the final drive input gear. 9. Rotate the transaxle 180 degrees. 10. NOTE: A high tightening torque specification between Nm ( lb-ft) is necessary to crush the collapsible spacer for correct bearing preload. NOTE: If the preload is too high, a new collapsible spacer must be installed. Using the special tools, tighten the nut to achieve the preload specification. 11. Rotate the transaxle 180 degrees. 12. NOTE: Make sure that the final drive rotates. Unlock the special tool. 13. Rotate the transaxle 180 degrees. 14. NOTICE: Make sure the bearing preload is within specification. NOTE: Rotate the gear 10 times to make sure that the bearings are correctly seated. Using the special tools, measure the rotating torque. 15. After achieving the correct torque, remove the special tools and stake the nut to prevent movement.
4 Page 4 of Rotate the transaxle 180 degrees. 17. Position the transfer shaft gears in the transaxle case. 18. Install the parking pawl return spring. 19. Connect the spring. 1. Install the parking pawl abutment. 2. Install the lever. 3. Install the pin. 4. Connect the spring. 20. Install the parking pawl assembly cover and bolts. 21. Install the differential case assembly. 22. Position the bearing cups.
5 Page 5 of Install the special tools. 24. NOTICE: Do not use the bolts from special service kit they will not work. Use only the bolts from the special service kit NOTE: The converter housing cover must be installed evenly or an incorrect reading will result. Using the special tools, assemble the transaxle for end play measurement. 1. Position the converter housing. 2. Install the special tool bolts and seat the case cover flat. 25. Remove the converter housing. 1. Remove bolts. 2. Remove the converter housing. 26. Remove the special tools. 27. Remove the bearing cups. 28. NOTE: If the plunger is above the contact surface, the reading will be incorrect. To determine the correct transfer shaft shim, measure the depth of the plunger on the special tool and select the correct transfer shaft shim. For additional information, refer to Specifications in this section.
6 Page 6 of NOTE: If the plunger is above the contact surface, the reading will be incorrect. To determine the correct differential shaft shim, measure the depth of the plunger on the special tool and select the correct differential shaft shim. For additional information, refer to Specifications in this section. 30. Using the special tool, install the correct transfer shaft shim and bearing cup in to the converter housing. 31. Using the special tool, install the correct differential shaft shim and differential case bearing cup into the converter housing. 32. Apply a one millimeter thick bead of Loctite Position the converter housing on the transaxle case and install the bolts. 34. Install the intermediate/overdrive band servo piston return spring.
7 Page 7 of Install the intermediate/overdrive servo piston. 36. Install the O-ring seal. 37. NOTE: The three bolts must be loosely installed, then tightened in sequence to compress the intermediate/overdrive spring evenly. Install the intermediate/overdrive band servo piston cover. 38. Install the manual control lever assembly and bolt. 39. NOTE: Lubricate the O-ring prior to assembly. Install the new O-rings on the manual control lever shaft. 40. Install the manual control lever shaft.
8 Page 8 of NOTE: The roll pin does not need to sit flush with the shifter assembly. Install a new manual control lever shaft roll pin. 42. Loosely install the transmission range (TR) sensor. 43. NOTE: The 1-2 accumulator piston may have a step. Check accumulator bores and pistons for damage. Install the accumulator pistons. 44. NOTE: The neutral drive accumulator springs are thinner than the 1-2 accumulator springs. Install the thinner and longer neutral drive accumulator springs. 45. Install the neutral drive accumulator piston. 46. Install the 1-2 accumulator springs. 47. Install the 1-2 accumulator piston.
9 Page 9 of Inspect the seals. Lubricate and install the transaxle internal harness electrical connector. 49. NOTE: Make sure that the manual valve is in the manual control valve shift lever. NOTE: Do not fully tighten the bolts at this stage. Install the main control valve body. 50. Tighten the main control valve body retaining bolts. Tighten the bolts in the sequence shown. 51. NOTE: It is necessary to connect the connectors in the same positions as noted in disassembly. Connector color letters are cast in the solenoid body. Install the main control wiring harness, connect the electrical connectors and install the ground wire bolt. 1. Solenoid SSC; Color N (Neutral/White). 2. Solenoid SSE; Color G (Green). 3. Solenoid SSD; Color L (Blue). 4. Solenoid PCA; Color B (Black). 5. Solenoid SSA; Color N (Neutral). 6. Solenoid SSB; Color B (Black). 52. Install the fluid filter.
10 Page 10 of Connect the transmission fluid temperature (TFT) sensor. 54. Apply a bead 1.5 mm diameter of Motorcraft TA-29 to the transaxle fluid pan. 55. Install the transmission fluid pan. 56. Rotate the transaxle 180 degrees.
27 E. Front wheel drive. 1. Transmission Description (Ford Focus 2000 only) 4 4 Speed Transmission F
1. Transmission Description (Ford Focus 2000 only) 4 4 Speed Transmission F Front wheel drive 27 E Maximum input torque after torque converter: 270 Lb-ft (365 N-m) Fully Electronic control Note: Mazda
DISASSEMBLY AND ASSEMBLY
307-01-1 Automatic Transaxle/Transmission 307-01-1 DISASSEMBLY AND ASSEMBLY Transaxle Special Tool(s) Dial Indicator Gauge With Holding Fixture 100-002 (TOOL-4201-C) Special Tool(s) Test Plate Screw Set,
2003 E-Series Workshop Manual
Page 1 of 20 SECTION 307-01B: Automatic Transmission 4R70W 2003 E-Series Workshop Manual ASSEMBLY Procedure revision date: 04/27/2006 Transmission Printable View (1828 KB) Special Tool(s) Dial Indicator
1998 Contour/Mystique Workshop Manual
SECTION 30-01: Automatic Transmission/Transaxle 1998 Contour/Mystique Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 09/14/2001 Main Controls Special Tool(s) Aligner, Selector Shaft 30-S290
SECTION Automatic Transaxle/Transmission 6R80
307-01-i Automatic Transaxle/Transmission 6R80 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 6R80 CONTENTS PAGE Main Control... 307-01-2 307-01-2 Automatic Transaxle/Transmission 6R80 Main Control
Automatic Transmission 5R44E and 5R55E
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 IN-VEHICLE REPAIR Main Control Valve Body Special Tool(s) Aligner, Valve Body 307-333 (T95L-70010-B) Aligner, Valve Body 307-334 (T95L-70010-C)
2002 F-Super Duty /Excursion Workshop Manual
Page 1 of 25 SECTION 307-01: Automatic Transaxle/Transmission 2002 F-Super Duty 250-550/Excursion Workshop Manual ASSEMBLY Procedure revision date: 05/23/2001 Transmission Special Tool(s) Remover, O-Ring
Page 1 of 22 SECTION 307-01: Automatic Transaxle/Transmission 4R70E/4R75E ASSEMBLY Procedure revision date: 05/29/2009 Transmission Printable View (1554 KB) Special Tool(s) Air Test Plate, Transmission
Page 1 of 75 303-01D Engine - 5.2L 32V Ti-VCT 2016 Mustang Assembly Procedure revision date: 12/15/2016 Special Tool(s) / General Equipment Engine Base Part Number: 6L084 205-142 (T80T-4000-J) Installer,
Shift Solenoids (SS)
2011 Mustang Report a problem with this article 307-01 Automatic Transaxle/Transmission 6R80 2011 Mustang IN-VEHICLE REPAIR Procedure revision date: 02/23/2011 Shift Solenoids (SS) Material Item Motorcraft
ASSEMBLY. Transmission Automatic Transmission 5R44E and 5R55E. Special Tool(s)
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 ASSEMBLY Transmission Special Tool(s) Holding Fixture, Transmission 307-262 (T93T-77002-AH) Special Tool(s) Installer, Transmission Extension Housing
SECTION B Manual Transaxle/Transmission TR6060
308-03B-i Manual Transaxle/Transmission TR6060 308-03B-i SECTION 308-03B Manual Transaxle/Transmission TR6060 CONTENTS PAGE Transmission... 308-03B-2 308-03B-2 Manual Transaxle/Transmission TR6060 308-03B-2
DISASSEMBLY. Transmission. All vehicles
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 DISASSEMBLY Transmission Special Tool(s) Holding Fixture, Transmission 307-262 (T93T-77002-AH) Special Tool(s) Remover, Servo 307-347 (T97T-7D021-A)
Differential Bearings
SECTION 205-02A: Rear Drive Axle/Differential Ford 7.5-Inch Ring Gear 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 04/02/2009 Differential Bearings Special Tool(s) 2 Jaw Puller
Differential Ring And Pinion
SECTION 205-02B: Rear Drive Axle/Differential Ford 8.8-Inch Ring Gear 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 01/06/2010 Differential Ring And Pinion Special Tool(s) 2 Jaw
2005 Mustang Workshop Manual
SECTION 205-00: Driveline System General Information 2005 Mustang Workshop Manual GENERAL PROCEDURES Procedure revision date: 07/29/2004 Driveline Angle Inspection Printable View (122 KB) Special Tool(s)
Shift Solenoid B (SSB) and Shift Solenoid D (SSD) Inverse Proportional VFS 2761
Item Description 1 Shift Solenoid A (SSA) Variable Force Solenoid (VFS) 2 Shift Solenoid C (SSC) VFS SSB and SSD use inverse proportional operation. As the current from the PCM decreases, the pressure
SECTION Front Drive Axle/Differential
205-03-i Front Drive Axle/Differential 205-03-i SECTION 205-03 Front Drive Axle/Differential CONTENTS PAGE Axle... 205-03-2 205-03-2 Front Drive Axle/Differential 205-03-2 Axle Special Tool(s) C-Frame
IN-VEHICLE REPAIR. Main Control Valve Body. Removal. 6. Disconnect the transaxle wiring harness electrical connector and TR sensor connector.
307-01-1 Automatic Transaxle/Transmission 307-01-1 IN-VEHICLE REPAIR Main Control Valve Body Material Item Thread Sealant with PTFE TA-24 Motorcraft MERCON Multi-Purpose (ATF) Transmission Fluid XT-2-QDX
IN-VEHICLE REPAIR. Differential Bearings. Rear Drive Axle/Differential Ford 7.5-Inch Ring Gear. Special Tool(s)
205-02A-1 IN-VEHICLE REPAIR Differential Bearings Special Tool(s) Protector, Drive Pinion Thread 205-460 Special Tool(s) Installer, Differential Shim 205-220 (T85L-4067-AH) 205-02A-1 2-Jaw Puller 205-D072
STEPS Install the (A) input shaft with long spliced end first. Install the (B) aligning pin.
1999 Ford Truck Econoline E450 Super Duty V10-6.8L VIN S Vehicle > Transmission and Drivetrain > Automatic Transmission/Transaxle > Service and Repair > Overhaul > 4R100 > Assembly STEPS 51-94 51. Install
Differential Bearings
SECTION 205-02B: Rear Drive Axle/Differential Ford 8.8-Inch Ring Gear 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 01/06/2010 Differential Bearings Special Tool(s) 2 Jaw Puller
1999 F-150/250 Workshop Manual
Page 1 of 30 SECTION 205-03: Front Drive Axle/Differential Ford 8.8-Inch Ring Gear 1999 F-150/250 Workshop Manual DISASSEMBLY AND ASSEMBLY Procedure revision date: 01/08/2003 Axle Front Drive Special Tool(s)
Engine. Special Tool(s) Adapter for (T97T-6256-A) Adapter for (T97T-6256-D)
SECTION 303-01A: Engine 4.0L SOHC 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 05/10/2010 Engine Special Tool(s) Adapter for 303-564 303-578 (T97T-6256-A) Adapter for 303-577 303-576
Assembly. NOTE: Before beginning assembly, perform/inspect the following:
Page 1 of 31 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's Reference Component Search: OK 1997 Ford Truck F 150 2WD Pickup V6-4.2L VIN 2
Model 4360 Teardown and Reassembly Instructions
Clean the outside surface of the transaxle. Place the shifter in neutral position. Remove detent cover screw (item 3), detent cover (item 4), detent springs (item 5), and detent balls (item 6). Use a magnet
Crankshaft Rear Seal with Retainer Plate
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Crankshaft Rear Seal with Retainer Plate Special Tool(s) Installer, Crankshaft Rear
ASSEMBLY. Transmission Automatic Transaxle/Transmission. Special Tool(s) Alignment Set, Fluid Pump 307-S039 (T74P X) Special Tool(s)
307-01-1 Automatic Transaxle/Transmission 307-01-1 ASSEMBLY Transmission Special Tool(s) Adjustment Set, Transmission Band 307-S022 (T71P-77370-A) Special Tool(s) Alignment Set, Fluid Pump 307-S039 (T74P-77103-X)
2005 Toyota RAV AUTOMATIC TRANSMISSIONS U240E & U241E Overhaul
2001-05 AUTOMATIC TRANSMISSIONS U240E & U241E Overhaul APPLICATION CAUTION: Flush oil cooler and oil cooler lines prior to transaxle installation. Oil cooling system contamination may cause premature transaxle
DIAGNOSIS AND TESTING
307-01-1 Automatic Transaxle/Transmission 307-01-1 DIAGNOSIS AND TESTING Transmission Connector Layouts Connector Reference and Terminal Readings Powertrain Control module (PCM) 1 Pressure control solenoid
1 of 14 11/19/ :45 AM
1 of 14 11/19/2016 11:45 AM 6F35 Digital Transmission Range (TR) Sensor Removal All vehicles 1. With the vehicle in NEUTRAL, position it on a hoist. 3.0L engine 2. Remove the Air Cleaner (ACL) outlet pipe.
2007 Explorer/Mountaineer/Explorer Sport Trac Workshop Manual MERCON V
2007 Explorer SECTION 307-01A: Automatic Transaxle/Transmission 5R55S 2007 Explorer/Mountaineer/Explorer Sport Trac Workshop Manual Report a problem with this article IN-VEHICLE REPAIR Procedure revision
DISASSEMBLY AND ASSEMBLY
205-02B-1 DISASSEMBLY AND ASSEMBLY Differential Case and Ring Gear Material Item Specification 205-02B-1 Special Tool(s) Additive Friction Modifier EST-M2C118-A XL-3 2-Jaw Puller 205-D072 (D97L-4221-A)
DISASSEMBLY AND ASSEMBLY
211-02-1 Power Steering 211-02-1 DISASSEMBLY AND ASSEMBLY Steering Gear Special Tool(s) Holding Fixture, Transmission 307-003 (T57L-500-B) Special Tool(s) Installer, Worm Bearing Locknut 211-012 (T66P-3553-B)
Diagnostic Trouble Code (DTC) Charts
SECTION 307-01: Automatic Transaxle/Transmission 5R55S 2009 Mustang Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 06/30/2009 Diagnostic Trouble Code (DTC) Charts DTC Chart **May also be
Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,
ASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s)
303-01A-1 ASSEMBLY Engine Special Tool(s) Tensioner, Timing Chain 303-571 (T97T-6K254-A) Special Tool(s) 303-01A-1 Installer, Crankshaft Vibration Damper 303-102 (T74P-6316-B) Holding Tool, Camshaft Sprocket
Page 1 of 7 Section 07-01A: Transmission, Automatic, E4OD IN-VEHICLE SERVICE 1993 Bronco/Econoline/F-Series Workshop Manual Valve Bodies and Intermediate Band Servo NOTE: If a transmission has been disassembled
2008 F-Super Duty Workshop Manual
13. Remove the mainshaft rear bearing cover. Inspect the mainshaft rear bearing cup for wear and damage. Install a new one as needed. Remove and discard the mainshaft rear bearing cover oil seal. 14. Remove
ASSEMBLY Procedure revision date: 11/22/2001
Page 1 of 39 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:08 PM To: 'Evan Groenke' Subject: 2.5L Engine Re-assembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop
2001 F-650/750 Workshop Manual
26. Pack the reverse idler gear bearings with lubricant. Use Moly number 2 lubricant or equivalent. 27. Install the following: 1. Assemble the reverse idler gear and bearings onto the idler shaft. 2. Position
TCI Turbo 400 Full Manual Valve Body. Shift Pattern: Park Reverse Neutral First Second Third. NOTE: You must reuse stock manual control valve.
TCI 221100 Turbo 400 Full Manual Valve Body Shift Pattern: Park Reverse Neutral First Second Third This Kit Contains: (1) Turbo 400 Full Manual Valve Body (1) Separator Plate & Gaskets (1) Pressure Regulator
Parking Brake Shoe: Adjustments
1997 Ford Truck F 350 2WD Pickup V8-460 7.5L VIN G EFI Copyright 2007, ALLDATA 9.50 Page 1 Parking Brake Shoe: Adjustments Transmission-Mounted Parking Brake Disassembly 1. Remove the Parking brake assembly
ABBREVIATIONS USED IN THIS MANUAL
IN6 INTRODUCTION Abbreviations Used in This Manual ABBREVIATIONS USED IN THIS MANUAL A/T ATM Automatic Transmission ATF Automatic Transmission Fluid B 0 Overdrive Brake B 1 Second Coast Brake B 2 Second
DRIVE AXLE - 4WD MODELS WITH INTEGRAL HOUSING
DRIVE AXLE - 4WD MODELS WITH INTEGRAL HOUSING 1988 Toyota Celica DRIVE AXLES Toyota Integral Housing Celica (Rear) DESCRIPTION housing. Drive axle assembly is hypoid type with integral carrier AXLE RATIO
DIFFERENTIALS & AXLE SHAFTS
DIFFERENTIALS & AXLE SHAFTS 2001 Chevrolet Camaro 2000-01 DRIVE AXLES General Motors Differentials & Axle Shafts Chevrolet; Camaro Pontiac; Firebird DESCRIPTION & OPERATION Drive axle is a semi-floating,
2010 Explorer, Mountaineer, Explorer Sport Trac Workshop Manual. IN-VEHICLE REPAIR Procedure revision date: 06/11/2009
SECTION 303-01B: Engine - 4.6L 2010 Explorer, Mountaineer, Explorer Sport Trac Workshop (3V) Manual IN-VEHICLE REPAIR Procedure revision date: 06/11/2009 Engine Lubrication Components - Exploded View Brackets,
2002 Crown Victoria/Grand Marquis Workshop Manual
Page 1 of 24 SECTION 303-01: Engine 2002 Crown Victoria/Grand Marquis Workshop Manual INSTALLATION Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Installer, Crankshaft Vibration Damper
AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series TRANSMISSION APPLICATION TABLE
Article Text ARTICLE BEGINNING AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series APPLICATION TRANSMISSION APPLICATION TABLE Vehicle Application Transmission Model Colt 3-Speed (1990-94)... F3A21 Colt Vista
DISASSEMBLY AND ASSEMBLY
205-03-1 Front Drive Axle/Differential Ford 8.8-Inch Ring Gear 205-03-1 DISASSEMBLY AND ASSEMBLY Axle Front Drive Special Tool(s) 2-Jaw Puller 205-D072 (D97L-4221-A) Special Tool(s) Carrier Bearing Replacer
DIAGNOSIS AND TESTING
307-01-1 Automatic Transmission 5R55S 307-01-1 DIAGNOSIS AND TESTING Transmission Connector Layouts Connector Reference and Terminal Readings Powertrain Control Module (PCM) C175b 1 Shift Solenoid A (SSA)
2002 F-150 Workshop Manual
Page 1 of 8 SECTION 307-01B: Automatic Transmission 4R70W 2002 F-150 Workshop Manual REMOVAL Procedure revision date: 04/02/2003 Transmission Special Tool(s) Retainer, Torque Converter 307-346 (T97T-7902-A)
Transaxle. 1. Mount the transaxle to Bench Mounted Holding Fixture T57L-500-B.
«1997 Aspire Table of Contents» «Group 07: TRANSAXLE» «Section 07-01: Transaxle, Automatic» «DISASSEMBLY» Transaxle CAUTION: To prevent dirt from entering the transaxle, it should be disassembled and kept
SECTION Automatic Transaxle/Transmission 6R80
307-01-i Automatic Transaxle/Transmission 6R80 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 6R80 CONTENTS PAGE IN-VEHICLE REPAIR Main Control... 307-01-2 307-01-2 Automatic Transaxle/Transmission
IN-VEHICLE REPAIR. Engine Front Cover
303-01A-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01A-1 Special Tool(s) SAE 5W-20 Premium WSS-M2C930-A Synthetic Blend Motor Oil Alignment Plate, Camshaft XO-5W20-QSP (in Canada
Engine Front Cover. Special Tool(s) 3-Jaw Puller 303-D121 or equivalent. Installer, Front Cover Oil Seal (T88T-6701-A)
SECTION 303-01B: Engine 4.6L (3V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/23/2008 Engine Front Cover Special Tool(s) 3-Jaw Puller 303-D121 or equivalent Installer, Front
file://c:\program Files\tsocache\OFFICE_5416\SY1~us~en~file=SY131B46.htm~gen~ref...
Page 1 of 41 SECTION 303-01B: Engine 4.6L and 5.4L 2000 F-150 Workshop Manual ASSEMBLY Procedure revision date: 01/27/2004 Engine 4.6L Special Tool(s) Compressor, Valve Spring 303-567 (T97P-6565-AH) Compressor
Engine. Special Tool(s) Compressor, Valve Spring (T97P-6565-AH) Compressor Spacer, Valve Spring (T91P-6565-AH)
Page 1 of 41 SECTION 303-01A: Engine 5.4L (2V) 2000 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis Workshop Manual ASSEMBLY Procedure revision date: 04/04/2003 Engine Special Tool(s) Compressor,
2012 NATEF Task Area A 2 Automatic Transmission
2012 NATEF Task Area A 2 Automatic Transmission A. General Transmission & Transaxle Diagnosis B. Transmission & Transaxle Maintenance & Adjustment C. In Vehicle Transmission & Transaxle Repair D. Off Vehicle
IN-VEHICLE REPAIR. Output Shaft Speed (OSS) Sensor. Removal
307-01-1 Automatic Transaxle/Transmission 6F50 307-01-1 IN-VEHICLE REPAIR Output Shaft Speed (OSS) Sensor Material Item MERCON V Automatic Transmission Fluid XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada)
Pinpoint Tests OSC Equipped Vehicle
SECTION 307-01: Automatic Transaxle/Transmission 5R55S 2009 Mustang Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 11/19/2008 Pinpoint Tests OSC Equipped Vehicle Special Tool(s) 73 III
1999 F-Super Duty Workshop Manual
Page 1 of 5 SECTION 307-01: Automatic Transaxle/Transmission 1999 F-Super Duty 250-550 Workshop Manual DISASSEMBLY AND ASSEMBLY OF SUBASSEMBLIES Procedure revision date: 01/26/2000 Main Control Valve Body
CERTAIN MODEL YEAR C-MAX HYBRID AND FUSION HYBRID VEHICLES TRANSMISSION INSPECTION AND REPAIR
PAGE 1 OF 25 CERTAIN 2013-2014 MODEL YEAR C-MAX HYBRID AND FUSION HYBRID VEHICLES TRANSMISSION INSPECTION AND REPAIR OVERVIEW Under certain driving conditions, the transfer shaft gear assembly bearing
COMPONENT LOCATOR > DISASSEMBLED VIEWS
Page 1 of 26 Service Manual: AUTOMATIC TRANSAXLE - 4T65-E - OVERHAUL COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Case and Associated Parts Disassembled View (1 of 4) 2004 Buick LeSabre 3.8L Eng Limited
Transmission Electronic Control System
SECTION 307-01: Automatic Transaxle/Transmission 5R55S 2009 Mustang Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 05/23/2008 Transmission Electronic Control System Electronic System
Additions, Revisions, or Updates
1 SUBJECT DATE Model 4 Single Model 4 Rear Tandem Pinion Bearing Repair October 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0141 Detroit Axles
MANUAL TRANSAXLE Return to Main Table of Contents
MANUAL TRANSAXLE Return to Main Table of Contents GENERAL... 2 MANUAL TRANSAXLE CONTROL... 12 SHIFT LEVER ASSEMBLY... 14 MANUAL TRANSAXLE... 15 MANUAL TRANSAXLE ASSEMBLY... 17 FIFTH SPEED SYNCHRONIZER
2007 Dodge Nitro R/T
ASSEMBLY AUTOMATIC TRANSMISSION - 42RLE NOTE: If the transmission assembly is being reconditioned (clutch/seal replacement) or replaced, it is necessary to perform the TCM QUICK LEARN Procedure using the
Differential Case COMPONENTS. DISASSEMBLY OF DIFFERENTIAL CASE 1. REMOVE RING GEAR (a) Place matchmarks on the ring gear and the case.
MT44 Differential Case COMPONENTS DISASSEMBLY OF DIFFERENTIAL CASE 1. REMOVE RING GEAR (a) Place matchmarks on the ring gear and the case. (b) Loosen the staked part of the lock plate. MT45 (c) Remove
2013 NATEF Task Area A-2 Automatic Transmission7-2013
2013 NATEF Task Area A-2 Automatic Transmission7-2013 A. General Transmission & Transaxle Diagnosis B. Transmission & Transaxle Maintenance & Adjustment C. In-Vehicle Transmission & Transaxle Repair D.
Transmission Diesel Engines
Page 1 of 17 SECTION 307-01B: Automatic Transaxle/Transmission TorqShift 6 2011 F-250, 350, 450, 550 Super Duty Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 11/12/2010 Transmission
Cylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual INSTALLATION Procedure revision date: 04/03/2009 Cylinder Head Special Tool(s) Compressor, Valve Spring 303-452 (T93P-6565-AR) Heavy Duty
SECTION Automatic Transaxle/Transmission 6R80
307-01-i Automatic Transaxle/Transmission 6R80 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 6R80 CONTENTS PAGE Transmission... 307-01-2 307-01-2 Automatic Transaxle/Transmission 6R80 307-01-2
1. Remove the parking brake assembly. 2. Remove the 4 bolts holding the yoke flange and drum. Remove the yoke flange and drive.
Disassembly NOTE: To replace the brake assembly, brake shoe and lining assemblies, or other operational components the complete parking brake assembly must be removed from the vehicle. 1. Remove the parking
MAIN CONTROL VALVE BODY. Removal 1. Disconnect the battery cables. 2. Remove the battery and tray.
1 of 17 MAIN CONTROL VALVE BODY Removal 1. Disconnect the battery cables. 2. Remove the battery and tray. 3. Disconnect the breather tube and mass air flow (MAF) / intake air temperature (IAT) sensor.
2006 Expedition/Navigator Workshop Manual
7. Remove the RH variable camshaft timing (VCT) oil control solenoid. For additional information, refer to Section 303-14. 8. Remove the RH ignition coils. For additional information, refer to Section
DRIVE AXLE - INTEGRAL HOUSING
DRIVE AXLE - INTEGRAL HOUSING 1993 Toyota Celica 1993 DRIVE AXLES Toyota Differentials & Axle Shafts - Integral Housing Toyota; Celica All-Trac DESCRIPTION Drive axle assembly is a hypoid type with integral
2006 Dodge RAM of 10 11/15/ :03 PM REMOVAL. Subarticles. Submodel: SLT Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS
EAR-PINION/RING - REMOVAL AND INSTALLATION 1 of 10 11/15/2012 12:03 PM 2006 Dodge RAM 1500 Submodel: SLT Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS Subarticles GEAR-PINION/RING - REMOVAL GEAR-PINION/RING
Disconnect the breather tube and mass air flow (MAF) /intake air temperature (IAT) sensor.
1 of 19 10/1/2011 11:11 AM oval 1. 2. Disconnect the battery cables. Remove the battery and tray. 3. Disconnect the breather tube and mass air flow (MAF) /intake air temperature (IAT) sensor. 4. Remove
2007 Explorer/Mountaineer/Explorer Sport Trac Workshop Manual SECTION A: Engine 4.0L SOHC. IN-VEHICLE REPAIR Procedure revision date: 04/20/2006
SECTION 303-01A: Engine 4.0L SOHC 2007 Explorer/Mountaineer/Explorer Sport Trac Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 04/20/2006 Camshaft Drive Cassette LH Printable View (577 KB)
Turbo 400 Trans Brake Valve Body Shift Pattern: Park Reverse Neutral 1st 2nd 3rd
TCI 221500 Turbo 400 Trans Brake Valve Body Shift Pattern: Park Reverse Neutral 1st 2nd 3rd This Valve Body will neutralize at shut-down by putting shifter In 2nd gear position This Kit Contains: (1) Turbo
DIAGNOSIS AND TESTING
307-01-1 Automatic Transaxle/Transmission 307-01-1 DIAGNOSIS AND TESTING Pinpoint Tests OSC Equipped Vehicle Special Tool(s) Transmission Fluid Pressure Gauge 307-004 (T57L-77820-A) Special Tool(s) MLP-TR
Bantam Tractor 3000 and 5000 Transmission and Differential Part Numbers. 1 ea Spline Shaft Bearing Front ND USA 8232
Bantam Tractor 3000 and 5000 Transmission and Differential Part Numbers Amount Part Name Part # Manufacture Bantam Part # 2 ea Cluster Gear Bearing Front and Rear B-1212 Torrington USA 8382 1 ea Spline
DIAGNOSIS AND TESTING
307-01-1 Automatic Transaxle/Transmission 307-01-1 DIAGNOSIS AND TESTING Diagnostic Trouble Code Charts Diagnostic Trouble Code Chart P0102, MAF MAF concerns MAF system High/low EPC REFER to the P0103,
12 September 2012 Valve Body # , , ,
12 September 2012 Valve Body # 1030416, 1030417, 1030418, 1030419 1 BD VALVE BODY For 1996-2004 Dodge 5.9L 12V/24V Cummins Trucks -- I n s t a l l a t i o n I n s t r u c t i o n s -- 1030416 1996-1998
2010 F-650, 750 Super Duty Workshop Manual
11. Check the seal for heat damage (bottom view). If the seal is stiff and brittle, and not pliable like the new seal (top view), it is probably heat damaged. Determine and fix the cause of excessive heat
SECTION C Engine 5.4L (4V)
303-01C-i Engine 5.4L (4V) 303-01C-i SECTION 303-01C Engine 5.4L (4V) CONTENTS PAGE SPECIFICATIONS... 303-01C-2 303-01C-2 Engine 5.4L (4V) 303-01C-2 SPECIFICATIONS Material Motorcraft Metal Surface Prep
Section 35 Chapter 3 PTO AND DIFFERENTIAL LOCK VALVE NH
Section 5 Chapter PTO AND DIFFERENTIAL LOCK VALVE 6-1740NH TABLE OF CONTENTS SPECIAL TORQUES... 5-2 SPECIFICATIONS... 5-2 PTO AND DIFFERENTIAL LOCK VALVE... 5- Troubleshooting... 5- Removal... 5-4 Disassembly...
Jatco 5 Speed ATRA. All Rights Reserved. Printed in U.S.A.
1 2 3 Table Of Contents Transmission Diassembly... 4 Front Pump... 16 Reverse/High Clutch Drum... 18 Direct Clutch Drum... 22 Low Clutch Drum... 26 Planetary Gearsets... 29 Transfer Gear/Reduction Gear...
Page 1 of 9 SECTION 303-01B: Engine 2.0L SPI 2002 Focus Workshop Manual ASSEMBLY Procedure revision date: 12/14/2000 Engine Special Tool(s) Crankshaft Rear Seal Pilot 303-329 (T88P-6701-B2) Crankshaft
DISASSEMBLY TRANSAXLE DISASSEMBLY AND ASSEMBLY. Part 1 Of 3
2004 Mitsubishi Truck Endeavor V6-3.8L SOHC Vehicle > Transmission and Drivetrain > Automatic Transmission/Transaxle > Service and Repair > Overhaul > F4A5A > Disassembly and Assembly DISASSEMBLY TRANSAXLE
M Ring and Pinion Installation
!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. Axle Shaft Removal (1994-2012 Mustang typical) STEP 1: STEP 2: Remove the 10 differential housing cover bolts and drain
Fluid Pump. Special Tool(s) Alignment Gauge, Transmission Fluid Pump Alignment Gauge, Transmission Fluid Pump
SECTION 307-01: Automatic Transaxle/Transmission 5R55S 2009 Mustang Workshop Manual DISASSEMBLY AND ASSEMBLY OF SUBASSEMBLIES Procedure revision date: 06/30/2009 Fluid Pump Special Tool(s) Alignment Gauge,
1995 Aerostar/Ranger/Explorer
Page 1 of 13 Section 03-01C: Engine, 4.0L V-6 DISASSEMBLY AND ASSEMBLY 1995 Aerostar/Ranger/Explorer Workshop Manual Engine Disassembly 1. NOTE: Before starting disassembly, remove all wiring harnesses,
IN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent
303-01A-1 IN-VEHICLE REPAIR Cylinder Head Special Tool(s) Torque Wrench Extension 303-575 (T97T-6256-F) or equivalent Special Tool(s) 303-01A-1 Timing Tool, Crankshaft TDC 303-573 (T97T-6303-A) or equivalent
1994 Mitsubishi Eclipse GS
APPLICATIONS CHRYSLER MOTORS MANUAL TRANS OVERHAUL - MITSUBISHI W5M & W6M SERIES MANUAL TRANSMISSIONS Mitsubishi W5M31, TRANSMISSION APPLICATIONS (CHRYSLER MOTORS) Vehicle Application Transmission Model
Page 1 of 8 2012 Ford F450 Super Duty 6.7L Eng Service Manual: ENGINE MECHANICAL - 6.7L DIESEL -- F250-F550 SUPER DUTY IN-VEHICLE REPAIR > OIL PAN - LOWER MATERIAL SPECIFICATIONS Item Motorcraft SAE 0W-30
2003 Taurus/Sable Workshop Manual
Page 1 of 24 SECTION 303-01A: Engine 3.0L (2V) ASSEMBLY 2003 Taurus/Sable Workshop Manual Engine Special Tool(s) Piston Ring Compressor 303- D032 (D81L-6002-C) Camshaft Bearing Set 303-017 (T65L-6250-A)
AUTOMATIC TRANSMISSIONS. General Motors Corp. Hydra-Matic 4L60-E Overhaul
1997-98 AUTOMATIC TRANSMISSIONS General Motors Corp. Hydra-Matic 4L60-E Overhaul APPLICATION TRANSMISSION APPLICATIONS Application Corvette Transaxle 4L60-E IDENTIFICATION The 4L60-E transmission can be
Technical Service Information
Technical Service Information VOLVO/SAAB AW0-4LE VALVE BODY EXPLODED VIEWS AND IDENTIFICATION OF COMPONENTS Refer to Figure 1 for Solenoid identification and locations on the valve body. Refer to Figure