AN-8 Plus Air Spray Gun Solvent-Based to Waterborne Conversion Kit

Size: px
Start display at page:

Download "AN-8 Plus Air Spray Gun Solvent-Based to Waterborne Conversion Kit"

Transcription

1 Instruction Sheet P/N 10874C AN-8 Plus Air Spray Gun Solvent-Based to Waterborne Conversion Kit 1. Description Use the solvent-based to waterborne conversion kit to convert your Nordson AN-8 Plus Air Spray gun for use with waterborne coatings. Waterborne coatings are conductive and easily transmit an electrostatic charge through the fluid stream. WARNING: Do not use the AN-8 Plus fluid tube and standard solvent-based coating delivery hose with waterborne coatings. The dielectric strength of the fluid tube and delivery hose is not sufficient to prevent the electrostatic charge from burning through the tube or hose. This conversion kit allows you to replace the fluid tube and delivery hose with Nordson high dielectric strength Isocore hose. The waterborne coating can then be charged at the source (isolated pump or pressure pot). The waterborne conversion service kit consists of a hose adapter assembly; bracket; and Isocore hose which includes all of the pre-assembled fittings that are necessary to convert your gun. 2. Preparation WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation. WARNING: Turn off the electrostatic power unit and ground the gun electrode before adjusting or servicing your electrostatic spray gun. Wait three minutes for voltage to bleed off before removing the electrostatic cable from the gun; and ground the cable end before touching it. Failure to observe this warning could result in a severe electric shock, causing personal injury or death.

2 2 Solvent-Based to Waterborne Conversion Kit 2. Preparation (contd) WARNING: Relieve fluid and air pressure from the system before disconnecting air lines and fluid hoses. Failure to observe this warning could result in severe personal injury or death. See Figure Disconnect the fluid and air hoses from the gun handle base. WARNING: Do not use the standard fluid tube and delivery hose installed on your gun when converting to use of waterborne coatings. Failure to observe this warning could result in equipment damage, personal injury, or death. 2. Remove and discard the fluid tube () from between the gun extension and handle.. Disconnect the electrostatic cable from the cable adapter at the base of the handle. Pull the cable out of the gun. 4. Refer to the Model AN-8 Plus Manual Electrostatic Air Spray Gun manual for assistance in performing the following steps: a. Remove the gun extension from the gun handle. b. Remove the insulating tube (2) and gun resistor (1) from the gun extension. 5. Before you reassemble the gun, fill the gun extension resistor bore with dielectric grease. Do not leave any air pockets. NOTE: Warming the applicator with hot tap water will make it easier to inject the grease into the bore.

3 Solvent-Based to Waterborne Conversion Kit 1 2 Fig. 1 Removing fluid tube, cable, and resistor from gun 1. Gun resistor. Fluid tube 2. Insulating tube. Installing the Isocore Hose See Figure Assemble the O-ring (1) and knurled coupling nut () onto the fitting (2). 2. Apply a thin film of dielectric grease from the O-ring (1) back, prior to installing the fitting (2) into the gun extension (A).. Install the fitting (2) into the inlet port in the bottom of the gun extension (A) and tighten securely. 4. Use the plug (4) to install the bracket (5) onto the cable adapter (C). Tighten the plug securely. 5. See Figure. Figure shows an Isocore B hose (with fittings) as it is shipped with this kit. Apply a thin film of dielectric grease from the O-ring (1) back to the threads (2) of the connector prior to installing the hose assembly into the gun extension.

4 4 Solvent-Based to Waterborne Conversion Kit. Installing the Isocore Hose (contd) 6. See Figure 2. Connect the fitting assembly (B) on the end of the Isocore hose (8) to the fitting (2) installed in the gun extension in step of this procedure. 7. Thread the knurled coupling nut () onto the fitting assembly (B) and hand-tighten it. 8. Install the gasket (7) and plug (6) into the cable port in the handle base. A 1 2 B 8 C Fig. 2 Installing Fitting in Gun Extension A. Gun extension B. Fitting assembly C. Cable adapter 1. O-ring 2. Fitting. Knurled coupling nut 4. Plug 5. Bracket 6. Plug 7. Gasket 8. Isocore hose

5 Solvent-Based to Waterborne Conversion Kit Fig. Isocore B Hose and Fittings, Shipped Assembled 1. O-ring 2. Threads on connector 4. Parts See Figure 2. Use the parts list below to identify and order parts in the solvent-based to waterborne conversion kit. If you require assistance in ordering, contact your Nordson Corporation representative. Item Part Description Quantity Note Kit, service, waterborne conversion O-ring, PTFE, 0.1 x 0.48 x 0.06 in Fitting, fluid tube, Isocore Nut, coupling, Isocore B Plug, O-ring boss, 1 / 2-20 in Bracket Plug, AN-8 plus cable Gasket, AN-8 plus cable Hose, Isocore B, with fitting assembly installed AR A NS Applicator, dielectric grease 1 B NOTE A: Shipped in increments of 25 ft. B: To receive a carton of 12 applicators of dielectric grease, order part AR: As Required NS: Not Shown

6 6 Solvent-Based to Waterborne Conversion Kit Original copyright date 199. Isocore, Nordson, and the Nordson logo are registered trademarks of Nordson Corporation.

Sure Coat 90 Degree Spray Extension

Sure Coat 90 Degree Spray Extension Instruction Sheet P/N 076A Sure Coat 90 Degree Spray Extension Description The 90 Degree Spray Extension is used on Sure Coat Automatic Powder Spray Guns. It allows powder to be sprayed at right angles

More information

0 900 psi Pressure-Reducing Diaphragm Regulator

0 900 psi Pressure-Reducing Diaphragm Regulator Instruction Sheet P/N 009506-09 0 900 psi Pressure-Reducing Diaphragm Regulator Description The Nordson 0 900 psi diaphragm regulator reduces high primary pressures to lower secondary pressures. It is

More information

Optional Nozzles for Versa-Spray and Versa-Spray II Guns

Optional Nozzles for Versa-Spray and Versa-Spray II Guns Instruction Sheet P/N 079A Optional Nozzles for Versa-Spray and Versa-Spray II Guns Description A wide variety of nozzles are available for Versa-Spray and Versa-Spray II powder spray guns. Manual and

More information

Paint/Solvent/Dump Valve and Flow-Through Valve

Paint/Solvent/Dump Valve and Flow-Through Valve Instruction Sheet P/N 08573D Paint/Solvent/Dump Valve and Flow-Through Valve. Description See Figure. The paint/solvent/dump valve is a normally-closed valve that opens to trigger and/or dump coating material.

More information

Standard and Conical AN Series Air Spray Nozzles

Standard and Conical AN Series Air Spray Nozzles Instruction Sheet P/N 107967E Standard and Conical AN Series Air Spray Nozzles Introduction The Nordson air spray nozzles described in this instruction sheet are categorized by their type of spray pattern:

More information

Mobile Powder Spray System Dolly with Hopper for Cable-Fed Systems

Mobile Powder Spray System Dolly with Hopper for Cable-Fed Systems Instruction Sheet P/N Mobile Powder Spray System Dolly with Hopper for Cable-Fed Systems WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document

More information

OBSOLETE. RA-16 Rotary Atomizer Upgrade Kit. Instruction Sheet P/N A. 1. Introduction. 2. Disassembly

OBSOLETE. RA-16 Rotary Atomizer Upgrade Kit. Instruction Sheet P/N A. 1. Introduction. 2. Disassembly Instruction Sheet P/N RA-16 Rotary Atomizer Upgrade Kit 1. Introduction This instruction sheet explains the procedure for installing the upgrade kit onto your RA-16 rotary atomizer. 2. Disassembly The

More information

Miniature Soft Seat Fluid Pressure Regulator

Miniature Soft Seat Fluid Pressure Regulator Instruction Sheet P/N 1. Description The Nordson miniature soft seat fluid pressure regulator is designed for use with hydraulic and pneumatic medias. The regulator body and wetted parts are constructed

More information

Installation Instructions for Series 3100V Low Level Indicator

Installation Instructions for Series 3100V Low Level Indicator Instruction Sheet P/N Installation Instructions for Series 3100V Low Level Indicator WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document

More information

TCU Flushing Manifold and RTD Installation

TCU Flushing Manifold and RTD Installation Instruction Sheet P/N 1614041-01 This instruction is for installing temperature control unit (TCU) flush manifold and RTD assembly onto the heat exchanger for both new systems and existing systems. Follow

More information

Series 3900/M Pump Retrofit Kit

Series 3900/M Pump Retrofit Kit Instruction Sheet P/N Series 900/M Pump Retrofit Kit WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related

More information

Inverted High Pressure Fluid Filters

Inverted High Pressure Fluid Filters Instruction Sheet P/N 33290-03 Description See Figure. Nordson high-pressure fluid filters prevent nozzle-plugging by filtering contaminants out of coating materials. These stainless steel, wall-mounted

More information

Electrostatic System Checks

Electrostatic System Checks Instruction Sheet P/N Electrostatic System s WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation.

More information

E-200 Module Service Kit

E-200 Module Service Kit Instruction Sheet E-200 Module Service Kit 1. Introduction These instructions describe how to remove and replace the E-200 module. The instructions include the following: S S S S Safety Unit Preparation

More information

Manifold-Mounted to Flange-Mounted Solenoid Valve Conversion

Manifold-Mounted to Flange-Mounted Solenoid Valve Conversion Instruction Sheet P/N 106501A03 Manifold-Mounted to Flange-Mounted Solenoid Valve Conversion WARNING: Allow only personnel with appropriate training and experience to operate or service the equipment.

More information

E-200 O-rings Service Kit

E-200 O-rings Service Kit Instruction Sheet E-00 O-rings Service Kit. Introduction These instructions describe how to replace the o-rings in the E-00 gun module. It is necessary to remove and disassemble the module when replacing

More information

Spray Pressure Control Manifold

Spray Pressure Control Manifold Instruction Sheet P/N 0870G0 WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. Introduction The

More information

Sure Coat Modular Gun Control System Part D: Gun Purge Module. Customer Product Manual Part B

Sure Coat Modular Gun Control System Part D: Gun Purge Module. Customer Product Manual Part B Sure Coat Modular Gun Control System Part D: Gun Purge Module Customer Product Manual Issued 4/0 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 4-919

More information

Two Component Meter Cylinder Assembly Replacement

Two Component Meter Cylinder Assembly Replacement Instruction Sheet P/N Two Component Meter Cylinder Assembly Replacement WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other

More information

Replacing a Gun RTD. Instruction Sheet P/N B. 1. Introduction. Using this Instruction Sheet

Replacing a Gun RTD. Instruction Sheet P/N B. 1. Introduction. Using this Instruction Sheet Instruction Sheet Replacing a Gun RTD WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation.

More information

Mobile Powder Spray System Dolly with Hopper

Mobile Powder Spray System Dolly with Hopper Instruction Sheet P/N 08766H Mobile Powder Spray System Dolly with Hopper WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all

More information

Spray Pressure Control Manifold

Spray Pressure Control Manifold Instruction Sheet P/N 0870-0 WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. Introduction The

More information

Solenoid Valve Installation Kit

Solenoid Valve Installation Kit Instruction Sheet P/N 7 5A Solenoid Valve Installation Kit WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related

More information

High Flow and 100 PLUS FB Powder Pumps

High Flow and 100 PLUS FB Powder Pumps Instruction Sheet P/N 07 987C High Flow and 00 PLUS FB Powder Pumps. Description The Nordson High Flow and 00 PLUS Powder Pumps are highly efficient venturi-type pumps designed primarily for pipe-coating

More information

Electrostatic Cable Care and Installation

Electrostatic Cable Care and Installation Instruction Sheet P/N 107913C Introduction NOTE: This manual provides general guidelines for electrostatic cable care and installation. For more specific instructions, refer to the appropriate spray gun

More information

5000 Gerotor Pump Service Instructions

5000 Gerotor Pump Service Instructions Instruction Sheet P/N 237569B WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. Introduction This

More information

Introduction. Pressed Shaft Flowmeter. Flowmeter Service Kits. Disassembly. Idler Shaft Removal

Introduction. Pressed Shaft Flowmeter. Flowmeter Service Kits. Disassembly. Idler Shaft Removal Flowmeter Service Kits Introduction See Figure. This instruction sheet provides repair procedures for flowmeters that use either pressed or screw-in shafts. Refer to the applicable repair procedure: Pressed

More information

EP-2 Si Three-Piston Pump

EP-2 Si Three-Piston Pump EP- Si Three-Piston Pump Customer Product Manual Issued 0/ For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) -99 or contact your local Nordson representative.

More information

Auto-Flo Air-Assist Automatic Dispensing Valve

Auto-Flo Air-Assist Automatic Dispensing Valve Auto-Flo Air-Assist Automatic Dispensing Valve Customer Product Manual Part NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments and inquiries about its

More information

Installing the Integral Platen Blow Off Valve

Installing the Integral Platen Blow Off Valve Instruction Sheet Installing the Integral Platen Blow Off Valve WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all

More information

EP-2 Three-Piston Pump

EP-2 Three-Piston Pump EP- Three-Piston Pump Customer Product Manual Issued 0/ For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) -99 or contact your local Nordson representative.

More information

Auto-Flo Panel Reinforcement Automatic Dispensing Valve

Auto-Flo Panel Reinforcement Automatic Dispensing Valve Auto-Flo Panel Reinforcement Automatic Dispensing Valve Customer Product Manual Part NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments and inquiries

More information

0-800 psi Carbide Seat Fluid Pressure Regulator

0-800 psi Carbide Seat Fluid Pressure Regulator Instruction Sheet P/N 0350C 0-800 psi Carbide Seat Fluid Pressure Regulator Description The Nordson 0-800 psi carbide seat fluid pressure regulator is designed for use with general liquid coatings. The

More information

Preventive Maintenance for Pail Melters

Preventive Maintenance for Pail Melters Instruction Sheet P/N Preventive Maintenance for Pail Melters 1. Introduction These procedures are recommended in addition to the standard preventive maintenance. Use them to keep yourvista controlled

More information

Installing an H-200 Integral Right-Angle Module

Installing an H-200 Integral Right-Angle Module Instruction heet P/N 187 723A Installing an H-200 Integral Right-Angle Module WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this

More information

Sure Coat Modular Gun Control System Part B: Pneumatic Modules. Customer Product Manual Part B

Sure Coat Modular Gun Control System Part B: Pneumatic Modules. Customer Product Manual Part B Sure Coat Modular Gun Control System Part B: Pneumatic Modules Customer Product Manual Issued 4/03 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800)

More information

Pro-Swirl Manifold Air Heater

Pro-Swirl Manifold Air Heater Instruction Sheet P/N 16107 01 Description The Pro-Swirl manifold heats air coming from the Pro-Swirl coalescent filter. The heater air then flows through the internal passages of the Pro-Swirl to maintain

More information

Rhino SD2/XD2 Electric Container Level Sensors for 125-mm Frames

Rhino SD2/XD2 Electric Container Level Sensors for 125-mm Frames Instruction Sheet P/N 1613207 01 Rhino SD2/XD2 Electric Container Level Sensors for 125-mm Frames Description See Figure 1. The Rhino SD2/XD2 electric container level sensor module uses magnetic sensors

More information

Fluidizing Pickup Tube Kits

Fluidizing Pickup Tube Kits Instruction Sheet P/N 303787-02 Introduction The fluidizing pickup tube kit retrofits your existing mobile powder system with fluidizing air. It injects fluidizing air at the pickup tube inlet with minimal

More information

Electric Vibratory Box Feeder Retrofit Kit

Electric Vibratory Box Feeder Retrofit Kit Instruction Sheet P/N 008E WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. Description This

More information

One-Gun Add-On Kit For Smart-Coat Controllers

One-Gun Add-On Kit For Smart-Coat Controllers Instruction Sheet P/N One-Gun Add-On Kit For Smart-Coat Controllers 1. Introduction This document contains procedures for installing a one-gun add-on kit to your Smart-Coat Controller. For additional information,

More information

Upgrading the Sure Coat Modular Gun Control System

Upgrading the Sure Coat Modular Gun Control System Instruction Sheet P/N 007365B Upgrading the Sure Coat Modular Gun Control System WARNING: Read the Safety section in the Sure Coat Modular Gun Control System manual before performing any of the following

More information

Inverted Dual High-Pressure Fluid Filter Assemblies

Inverted Dual High-Pressure Fluid Filter Assemblies Instruction Sheet P/N 1093-04 Inverted Dual High Pressure Fluid Filter Assemblies Introduction WARNG: High pressure fluids are hazardous. To prevent serious injury when installing and servicing filters,

More information

Blow Off Valve Retrofit Kit

Blow Off Valve Retrofit Kit Instruction Sheet P/N 37 56C low Off Valve Retrofit Kit WRNING: llow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation..

More information

Encore and Spectrum (Global) Powder Feed Center Clamping Cylinder

Encore and Spectrum (Global) Powder Feed Center Clamping Cylinder Instruction Sheet P/N 6480-0 Encore and Spectrum (Global) Powder Feed Center Clamping Cylinder WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in

More information

Air Spray Proportioning Valve

Air Spray Proportioning Valve Instruction Sheet P/N Air Spray Proportioning Valve. Installation The air spray proportioning valve provides close regulation of air spray characteristics for air spray versions of the Pro-Flo dispensing

More information

Back Pressure Regulator

Back Pressure Regulator Instruction Sheet P/N 108652H Description The Nordson back pressure regulator is a spring-loaded, hand-operated fluid pressure regulator designed for use with general liquid coating materials. The regulator

More information

TCU Static Mixer Installation

TCU Static Mixer Installation Instruction Sheet P/N 1611023-01 TCU Static Mixer Installation Use the following procedures to install static mixers into the heat exchange assembly. The installation will require the disassembly of both

More information

PREVIOUS GENERATION. Encore Manual Powder Spray Gun Trigger Switch Replacement. Introduction. Preparation. Gun Disassembly

PREVIOUS GENERATION. Encore Manual Powder Spray Gun Trigger Switch Replacement. Introduction. Preparation. Gun Disassembly Instruction Sheet P/N 1102249A Encore Manual Powder Spray Gun Trigger Switch Replacement Introduction Preparation Gun Disassembly The Encore trigger switch has been redesigned to eliminate the notches

More information

Series AD-31 Handgun Swivel Connector Replacement Kit P/N and P/N

Series AD-31 Handgun Swivel Connector Replacement Kit P/N and P/N Instruction heet eries AD-31 Handgun wivel Connector Replacement Kit P/N 238 808 and P/N 238 809 1. Description This instruction sheet contains procedures for replacing the swivel connector on eries AD-31

More information

Prodigy Mobile Box Unloader System

Prodigy Mobile Box Unloader System Instruction Sheet P/N 090A Prodigy Mobile Box Unloader System Description The Prodigy Mobile Box Unloader system unloads 5 kg (50 lb) boxes of powder and pumps the powder to spray gun feed hoppers. Systems

More information

Rhino VE Follower Modules

Rhino VE Follower Modules Instruction Sheet P/N 08 0 Description See Figure. The follower module attaches onto the hydraulic section of the pump (). It is designed to force material out of straight-sided containers. Follower plate

More information

Series 3000V Low Level Indicator

Series 3000V Low Level Indicator Instruction Sheet P/N 237 473A Series 3000V Low Level Indicator 1. Introduction The low level indicator sends a signal to an external device when the adhesive level in the applicator s tank is low. The

More information

Hard Seat Fluid Pressure Regulator

Hard Seat Fluid Pressure Regulator Instruction Sheet P/N 04742-02 Description The Nordson hard seat fluid pressure regulator is designed for use with abrasive coatings. The regulator body is constructed of stainless steel with a nickel-plated

More information

Converting an FP-200 Extrusion Gun to an FP-200 Swirl Gun

Converting an FP-200 Extrusion Gun to an FP-200 Swirl Gun Instruction Sheet P/N 237494_02 Converting an FP-200 Extrusion Gun to an FP-200 Swirl Gun WARNING! Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this

More information

Rhino SD3/XD3 Air Motor

Rhino SD3/XD3 Air Motor Rhino SD3/XD3 Air Motor Customer Product Manual Issued 6/18 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local Nordson

More information

0-500 PSI Soft Seat Fluid Pressure Regulator

0-500 PSI Soft Seat Fluid Pressure Regulator Instruction Sheet P/N 0953A Description The Nordson 0-500 psi soft seat fluid pressure regulator is designed for use with nonabrasive liquid coatings. The regulator body is constructed of stainless steel

More information

Pattern Air Control Kit (PACK)

Pattern Air Control Kit (PACK) Instruction Sheet P/N 044445B0 WARNING: Allow only personnel with appropriate training and experience to operate or service the equipment. The use of untrained or inexperienced personnel to operate or

More information

Nylon Fluid Regulators

Nylon Fluid Regulators Instruction Sheet P/N 08880B Introduction The FR- and RA- nylon fluid regulators are patented, electrically non-conductive, air-operated, pressure regulators. Except for the body shape and fluid connection

More information

Soft Seat Fluid Pressure Regulator

Soft Seat Fluid Pressure Regulator Instruction Sheet P/N 04622F Description The Nordson soft seat fluid pressure regulator is designed for use with nonabrasive liquid coatings. The regulator body is constructed of stainless steel with a

More information

Spectrum VT Inline Powder Feed Pump

Spectrum VT Inline Powder Feed Pump Instruction Sheet P/N 160919 01 Spectrum VT Inline Powder Feed Pump WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other

More information

Prodigy HDLV Pump. Customer Product Manual Part A02

Prodigy HDLV Pump. Customer Product Manual Part A02 Prodigy HDLV Pump Customer Product Manual Issued 1/07 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local Nordson representative.

More information

RA-20 Paint/Solvent/Dump Valve

RA-20 Paint/Solvent/Dump Valve Instruction Sheet P/N 74B0 RA-0 Paint/Solvent/Dump Valve Description The paint/solvent valve is a normally closed valve used to trigger coating material. The valve may be used alone to actuate paint or

More information

Tribomatic II Extended Automatic Powder Spray Gun

Tribomatic II Extended Automatic Powder Spray Gun Tribomatic II Extended Automatic Powder Spray Gun Customer Product Manual Issued 7/06 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-939 or contact

More information

Prodigy HDLV Manual System Installation Instructions

Prodigy HDLV Manual System Installation Instructions Prodigy HDLV Manual System Installation Instructions Instruction Sheet P/N 1062384C WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document

More information

VL400 Melters. Safety. Introduction. Nordson Corporation OPERATOR S CARD P/N A

VL400 Melters. Safety. Introduction. Nordson Corporation OPERATOR S CARD P/N A Nordson Corporation OPERATOR S CARD P/N 052644A VL400 Melters Safety WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other

More information

Model C-1 Electrostatic Airless Spray Gun OBSOLETE. Customer Product Manual. Part D NORDSON CORPORATION AMHERST, OHIO USA

Model C-1 Electrostatic Airless Spray Gun OBSOLETE. Customer Product Manual. Part D NORDSON CORPORATION AMHERST, OHIO USA Model C-1 Electrostatic Airless Spray Gun Customer Product Manual Part NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments and inquiries about its products.

More information

NRPS-100 Rotary Sieve

NRPS-100 Rotary Sieve NRPS-100 Rotary Sieve Customer Product Manual Part For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local Nordson representative.

More information

OPERATOR S CARD. Select Series H-440 Hot Melt Dispensing Guns. Safety. Description. Nordson Corporation P/N D

OPERATOR S CARD. Select Series H-440 Hot Melt Dispensing Guns. Safety. Description. Nordson Corporation P/N D Nordson Corporation OPERATOR S CARD P/N 321 198D Select Series H-440 Hot Melt Dispensing Guns Safety WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions

More information

Iso-Flo Coupling Repair

Iso-Flo Coupling Repair Instruction Sheet P/N 229782C Iso-Flo Coupling Repair Introduction This instruction sheet covers the repair of the male and female couplings used in the Automatic and Manual Iso-Flo HD Voltage Block Systems,

More information

Prodigy HDLV Generation II Pump Panel

Prodigy HDLV Generation II Pump Panel Prodigy HDLV Generation II Pump Panel Customer Product Manual Issued 01/10 For parts and technical support, call the Finishing Customer Support Center at (800) 433-9319. This document is subject to change

More information

CoolWave 2 Phase Control Board and Cable Replacement Kit

CoolWave 2 Phase Control Board and Cable Replacement Kit Instruction Sheet P/N 1102452-02 CoolWave 2 Phase Control Board and Cable Replacement Kit Use the Phase Control Board and Cable Kit to upgrade your CoolWave 2 power supply to the new configuration. NOTE:

More information

Filter. Table of Contents. Section 10. Filter NOTE: This section applies to applicators with an out-in filter.

Filter. Table of Contents. Section 10. Filter NOTE: This section applies to applicators with an out-in filter. Filter 10-1 Section 10 Filter NOTE: This section applies to applicators with an out-in filter. Table of Contents Filter...................................................... 10-1 Introduction................................................

More information

Description. Rhino SD2/XD2 Follower Modules

Description. Rhino SD2/XD2 Follower Modules Rhino SD/XD Follower Modules Description See Figure. The follower module attaches onto the hydraulic section of the pump (). It is designed to force material out of straight-sided containers. Standard

More information

Description. Repair. Rhinor XD2 Type-H Low Level Drum Proximity Sensor. Replacing the Proximity Sensor

Description. Repair. Rhinor XD2 Type-H Low Level Drum Proximity Sensor. Replacing the Proximity Sensor Rhinor XD2 Type-H Low Level Drum Proximity Sensor Description See Figure 1. The Rhino XD2 Type-H Low Level Drum Proximity Sensor (1) monitors the distance between the bottom of the follower plate and the

More information

Circulating and Non-Circulating Color Change Manifolds

Circulating and Non-Circulating Color Change Manifolds Circulating and Non-Circulating Color Change Manifolds Customer Product Manual Part NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments and inquiries about

More information

High-Pressure Fluid Filters

High-Pressure Fluid Filters High-Pressure Fluid Filters Customer Product Manual Part 107971C02 NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments and inquiries about its products.

More information

Encore Manual Powder Spray Gun Trigger Switch Replacement

Encore Manual Powder Spray Gun Trigger Switch Replacement Instruction Sheet P/N 1096694A Encore Manual Powder Spray Gun Trigger Switch Replacement Preparation 1. Remove the nozzle nut, nozzle, and electrode assembly. 2. Disconnect the powder feed hose adapter,

More information

Normally Open H200 and 90_ CF200 Module Seal Rebuild Kit

Normally Open H200 and 90_ CF200 Module Seal Rebuild Kit Instruction Sheet 108 792A Normally Open H200 and 90_ CF200 Module Seal Rebuild Kit 1. Description Use this rebuild kit to service the following modules: S Normally Open H200 (N.O. H200) Module -- P/N

More information

Description. Rhino SD2/XD2 Follower Modules

Description. Rhino SD2/XD2 Follower Modules Rhino SD/XD Follower Modules Description See Figure. The follower module attaches onto the hydraulic section of the pump (). It is designed to force material out of straight-sided containers. Standard

More information

Rhino SD3/XD3 5-Gallon Follower Modules

Rhino SD3/XD3 5-Gallon Follower Modules Rhino SD3/XD3 5-Gallon Follower Modules Customer Product Manual Part 6033 03 Issued 6/8 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-939 or

More information

Encore HD Powder Spray System with Prodigy Pump Cabinet

Encore HD Powder Spray System with Prodigy Pump Cabinet Encore HD Powder Spray System with Prodigy Pump Cabinet Customer Product Manual Part 604979-06 Issued 05/8 For parts and technical support, call the Industrial Coating Systems Customer Support Center at

More information

Module. Section 9. NOTE: This section applies to applicators with CC200 modules B Issued 6/01. Manual 42-CF200-CM-01

Module. Section 9. NOTE: This section applies to applicators with CC200 modules B Issued 6/01. Manual 42-CF200-CM-01 Section 9 NOTE: This section applies to applicators with CC200 modules. 9-0 Table of Contents i Table of Contents Section 9 1. Introduction............................................... 9-1 2. Specifications.............................................

More information

Prodigy HDLV Generation II Manual System Installation Instructions

Prodigy HDLV Generation II Manual System Installation Instructions Prodigy HDLV Generation II Manual System Installation Instructions Instruction Sheet P/N 1081707A WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions

More information

Econo-Coat Manual Powder Spray Gun

Econo-Coat Manual Powder Spray Gun Econo-Coat Manual Powder Spray Gun Customer Product Manual Issued 0/03 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-939 or contact your local

More information

Prodigy HDLV Pump Manifold and Circuit Board

Prodigy HDLV Pump Manifold and Circuit Board Prodigy HDLV Pump Manifold and Circuit Board Customer Product Manual Issued 05/08 For parts and technical support, call the Finishing Customer Support Center at (800) 433-939. This document is available

More information

Universal Automatic Non-Conductive Fluid Regulator

Universal Automatic Non-Conductive Fluid Regulator Universal Automatic Non-Conductive Fluid Regulator Customer Product Manual Part 1017527 04 Issued 3/18 NORDSON CORPORATION AMHERST, OHIO USA Table of Contents tents Safety... 1 Qualified Personnel... 1

More information

Tribomatic II Purgeable Automatic Powder Spray Gun

Tribomatic II Purgeable Automatic Powder Spray Gun Tribomatic II Purgeable Automatic Powder Spray Gun Customer Product Manual Issued 4/0 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 4-99 or contact

More information

Description. Rhino EFD Bulk Unloader Packages

Description. Rhino EFD Bulk Unloader Packages Rhino EFD Bulk Unloader Packages Description See Figure. The Rhino EFD Pail and -Gallon Drum Bulk Unloader Packages consist of the following major components: Pump () Controls () Frame () Follower Plate

More information

Prodigy HDLV System Troubleshooting - Generation III

Prodigy HDLV System Troubleshooting - Generation III Prodigy HDLV System Troubleshooting - Generation III Instruction Sheet P/N 1081071-05 Use the procedures listed in this document to isolate and correct common problems with Prodigy HDLV Systems. Refer

More information

A7A Single and Dual Automatic Airless Spray Guns

A7A Single and Dual Automatic Airless Spray Guns A7A Single and Dual Automatic Airless Spray Guns Customer Product Manual Issued 8/06 For parts and technical support, call the Finishing Customer Support Center at (800) 433-939. This document is available

More information

11-1 Electrical System NOTE: Table of Contents Electrical System

11-1 Electrical System NOTE: Table of Contents Electrical System Electrical System - Section Electrical System NOTE: This section applies to applicators with Universal C-style cordsets. Table of Contents Electrical System........................................... -

More information

Colormax Powder Coating System Color Change Process

Colormax Powder Coating System Color Change Process Nordson Corporation OPERATOR S CARD P/N 1015049B Colormax Powder Coating System Color Change Process Safety WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions

More information

Pro-Meter Gear Metering Pump

Pro-Meter Gear Metering Pump Pro-Meter Gear Metering Pump Customer Product Manual Part 0808E-0 Issued 4/6 NORDSON CORPORATION AMHERST, OHIO USA tents Table of Contents Safety... Qualified Personnel... Intended Use... Regulations and

More information

Versa-Spray IPS Manual Electrostatic Porcelain Enamel Powder Spray Gun

Versa-Spray IPS Manual Electrostatic Porcelain Enamel Powder Spray Gun Versa-Spray IPS Manual Electrostatic Porcelain Enamel Powder Spray Gun Customer Product Manual Issued 11/06 For parts and technical support, call the Industrial Coating Systems Customer Support Center

More information

Filter. Table of Contents. Section 10. Filter NOTE: This section applies to applicators with an in-out filter.

Filter. Table of Contents. Section 10. Filter NOTE: This section applies to applicators with an in-out filter. Filter 10-1 Section 10 Filter NOTE: This section applies to applicators with an in-out filter. Table of Contents Filter...................................................... 10-1 Introduction................................................

More information

55-Gallon Powder Drum Truck

55-Gallon Powder Drum Truck Instruction Sheet P/N 0 0 -Gallon Powder Drum Truck for Bulk-Feed Powder Transfer Systems Description See Figure. The -gallon powder drum truck automatically adds bulk powder to a powder coating system

More information

A16A Inside Stripe Gun

A16A Inside Stripe Gun A6A Inside Stripe Gun Customer Product Manual Issued 5/0 For parts and technical support, call the Finishing Customer Support Center at (800) 433-939. This document is subject to change without notice.

More information

Sure-Max Powder Transfer System

Sure-Max Powder Transfer System Sure-Max Powder Transfer System Customer Product Manual Issued 7/06 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local

More information

Nordson Airless Nozzle Tester

Nordson Airless Nozzle Tester Instruction Sheet P/N Nordson Airless Nozzle Tester. Introduction The Nordson airless nozzle tester is used to test the flow rate of flanged airless nozzles. The results of the tests can be used to determine

More information