TECHNICAL INSTRUCTIONS

Size: px
Start display at page:

Download "TECHNICAL INSTRUCTIONS"

Transcription

1 TECHNICAL INSTRUCTIONS PRADO SPIRAL CABLE SUB-ASSEMBLY REPLACEMENT 1. OPERATION FLOW CHART IDENTIFICATION OF AFFECTED VEHICLES PREPARATION WORK PROCEDURE

2 Safety Precautions Be sure to observe the following precautions to prevent accidents and injuries. - Park the vehicle and chock the wheels. - If it is necessary to start the engine, perform the operation in a well ventilated area. - Before removing and reinstalling heavy parts such as the engine, transmission and differential using specified tools, check that there are no problems with the tools. - When working in a group of 2 or more, each person must work to ensure the safety of all team members. - To prevent burns and other injuries, use extra caution when handling parts that are subject to high temperatures, as well as rotating, sliding, or vibrating parts. - When lifting the vehicle using a jack, support it in the specified location using a safety stand. - When lifting the vehicle using a lift, lock the lift for safety. Also perform the following operation with care. Use of auto lift - Make absolutely certain that there are no other workers and no tools, parts, or other objects within the movable range of the lift. Also, be sure to announce all lift operations out loud (such as Raising the lift! and Lowering the lift! ) to alert other workers. - When raising or lowering the lift, pay attention to the positions of your arms, legs, and other body parts, and be extremely careful to prevent them from being caught in the lift. Use of brake cleaner - Use brake cleaner for appropriate purposes in accordance with instructions in the manual. - Do not use brake cleaner to remove dirt or stains from the engineer clothes and so forth, as it can catch on fire and cause serious burns. < Precautions > - Do not use brake cleaner near flames or fire. - Do not use large amounts of brake cleaner in a room where a fire is burning. - Do not keep brake cleaner in a place subject to high temperatures exceeding 40 C, such as a place subject to direct sunlight or near fire. - Do not put brake cleaner in fire. Edges - When handling the edges of parts and panels, wear protective gloves or apply protective tape to the edges to prevent injuries to your hands and fingers. 2

3 1. OPERATION FLOW CHART Check whether or not the vehicle has the affected VIN. No Yes Replace the spiral cable sub-assembly Finish Return the vehicle to original state and finish the work. 3

4 2. IDENTIFICATION OF AFFECTED VEHICLES 2.1. COVERED VIN RANGE Model Name Prado VIN Range WMI VDS VIS Production Period JTE BH3FJ* * ~* ~ JTE BH9FJ* * ~* ~ JTE BU3FJ* * ~* ~ JTE BU9FJ* * ~* ~ JTE BX3FJ* * ~* ~ JTE BX9FJ* * ~* ~ JTE CH3FJ* * ~* ~ JTE CX9FJ* * ~* ~ JTE JU9FJ* * ~* ~ JTE BD3FJ* *K000105~*K ~ JTE BD9FJ* *K000109~*K ~ JTE BH3FJ* *K000126~*K ~ JTE BH9FJ* *K000145~*K ~ JTE BU3FJ* *K000620~*K ~ JTE BU9FJ* *K000101~*K ~ JTE BX3FJ* *K005870~*K ~ JTE BX9FJ* *K000106~*K ~ JTE JU9FJ* *K000225~*K ~ Note: # indicates that various characters may occupy that position. Not all vehicles in these VIN ranges, are affected and/or sold in your country. For the detailed list of concerned vehicles, please refer to the attached VIN list. 4

5 2.2. VEHICLE IDENTIFICATION NUMBER LOCATION VIN is stamped on the cowl panel. It is also stamped on the certification label as shown in the illustration. A: Vehicle Identification Number Plate B: Certification Label C:Name Plate Label D:Frame Number A A B C B D 5

6 3. PREPARATION 3.1. Replacement components Parts: Part Name Part No. Qty Remarks Spiral Cable FLD Kit CABLE SUB-ASSY, SPIRAL GREASE Spiral cable sub-assembly replacement Special Service Tools (SST): Illustration Part Name Part No. Qty Remarks Puller C Set Hanger 150 ( ) 1 Slide Arm ( ) 1 For removal and installation of the steering wheel Center Bolt 150 ( ) 1 Claw No.2 ( ) 1 Recommended Tools: Part Name Part No. Qty Remarks GTS (Global Techstream) - 1 "TORX" Socket T30-1 For DTC checks (Intelligent Tester can also be used instead.) For removal and installation of the horn button 6

7 Equipment: Part Name Part No. Qty Remarks Torque Wrench - 1 Grease - Protective Tape - Marker Pen - Appropriate quantity Appropriate quantity Appropriate quantity For checking tightening torque For lubrication For component protection For marking (any color other than green, blue and yellow) 7

8 4. WORK PROCEDURE <TABLE OF CONTENTS> A. WORK OUTLINE...9 B. CAUTION FOR LOCK PIN OF NEW SPIRAL CABLE...9 C. PRECAUTIONS FOR AIRBAG REMOVAL AND REINSTALLATION D. PRECAUTIONS FOR ALL OPERATIONS E. COMPONENTS F. REMOVE SPIRAL CABLE G. INSTALL SPIRAL CABLE

9 A. WORK OUTLINE Replacing the spiral cable. B. CAUTION FOR LOCK PIN OF NEW SPIRAL CABLE 1. LOCK PIN FOR NEW SPIRAL CABLE (a) DO NOT break/snap off the lock pin until just installing the steering wheel. Otherwise, the center position of a new spiral cable will be misaligned. 9

10 C. PRECAUTIONS FOR AIRBAG REMOVAL AND REINSTALLATION If the airbag system is not removed or reinstalled by the specified procedures, the airbag system may unintentionally be activated during the work, causing a serious accident that could lead to death. In addition, any errors in work could cause the airbag system to fail to operate when necessary. For that reason, pay careful attention to the instructions in this document and ensure safety during your work. 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (a) In order to prevent the airbag system from unintentionally operating, disconnect the negative battery terminal cable. (b) Wait at least 90 seconds after the battery cable is disconnected, to prevent possible deployment of the airbag. The airbag system is provided with a backup power supply. 2. REMOVE STATIC ELECTRICITY (a) Touch any metallic portion of the vehicle body to discharge the static electricity before starting work. 10

11 3. HANDLING OF AIRBAGS (a) After the horn button is removed from the vehicle, place and store it so that the airbag deployment surface faces upward. CAUTION: If the airbag is stored in an improper manner, a serious accident that could lead to death may result if the airbag is activated unexpectedly. 11

12 D. PRECAUTIONS FOR ALL OPERATIONS 1. PRECAUTIONS WHEN RAISING VEHICLE USING A LIFT OR JACK (a) Refer to the respective repair manual and follow the instructions within the Introduction section to ensure safety when working. (b) Ensure the safety of all personnel near the lift or jack, including yourself, before beginning work. Also announce all lift and jack operations out loud to prevent any personnel from being caught or harmed in any way. 2. WEAR PROTECTIVE EYEWEAR (a) Wear protective eyewear when working under vehicle or where there is any risk of flying parts or debris. 3. DO NOT USE BRAKE CLEANER AS STAIN REMOVER (a) Do not spray brake cleaner onto any clothes since it is a flammable solvent that vaporizes easily. Do not use it near cigarettes or stoves as this can cause serious burns and injuries. 4. AVOID BURNS (a) If the engine is hot, wear protective gloves to prevent burns. 12

13 5. VEHICLE PROTECTION (a) A fender cover, a grill cover, seat covers tape etc. must be used to protect the vehicle from dirt or scratches. NOTE: The protective measures listed above may not be shown in some illustrations to allow easy identification of the work location and to make the illustrations simple and easy to read. 6. HANDLING OF REMOVED PARTS (a) Destroy or mark and then store removed parts in a separate container so as to not be assembled again in error. (b) Check the removed parts when performing the completion inspection. NOTE: The parts shown in the illustration to the left are examples only and differ from the actual replacement parts. 7. DO NOT BREAK PARTS WHEN WORKING INSIDE ENGINE COMPARTMENT (a) Do not break parts by carelessly placing hands inside and leaning on the engine compartment while being preoccupied by work. 8. CHECK INSIDE ENGINE COMPARTMENT BEFORE ENGINE START-UP (a) Check that all necessary parts are installed. (b) Check that no tools or pieces of cloth are left inside the engine compartment. 13

14 E. COMPONENTS 14

15 F. REMOVE SPIRAL CABLE 1. CHECK FOR DTC (a) If DTCs are output, check and record the DTCs and freeze frame data and repair as necessary. 2. RECORD AUDIO AND AIR CONDITIONING SETTINGS (a) When the battery cable is disconnected, audio, air conditioning etc. settings may be reset. Therefore, before disconnecting the cable from the negative (-) battery terminal, make a note of the settings. 3. RECORD STEERING COLUMN TILT AND TELESCOPING POSITIONS 4. MOVE STEERING COLUMN (a) In order to obtain an enough space for removal of the steering column cover, lift up the steering wheel to the most upward position, and pull the steering wheel toward you as far as it can go. 5. CHECK STRAIGHT AHEAD POSITION FOR STEERING WHEEL 15

16 6. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (a) Turn the ignition switch off. (b) Disconnect the cable from the negative (-) battery terminal. Work must be started at least 90 seconds after the cable is disconnected from the negative (-) battery terminal. CAUTION: Wait at least 90 seconds after the battery cable is disconnected, to prevent possible deployment of the airbag. The airbag system is provided with a backup power supply. 7. REMOVE LOWER No.3 AND No.2 STEERING WHEEL COVER (a) Using a thin flat tip screwdriver with its tip wrapped in protective tape, disengage the claws to detach the No.3 steering wheel cover. (b) Do the same for the No.2 steering wheel cover. 8. REMOVE HORN BUTTON ASSEMBLY CAUTION: The airbag system has the backup power supply. For that reason, wait at least 90 seconds after disconnecting the negative terminal cable before removing the horn button. (a) Using a "TORX" socket (T30), loosen the 2 "TORX" screws until they rotate freely. NOTE: The screws cannot be removed because they are in the screw case. 16

17 (b) Pull out the horn button toward you. CAUTION: DO NOT pull on the wire harness when the horn button is extracted. (c) Using a flat-tip screwdriver, unlock the airbag connectors, and then disconnect them. (d) Disconnect the horn connector, and then remove the horn button. (e) Place and store the horn button so that the portion where the airbag is deployed faces upward. 9. REMOVE STEERING WHEEL ASSEMBLY (a) Disconnect the horn wire connector. (b) Turn the nut 2 to 3 times to loosen it. (c) Put matchmarks onto the steering wheel and main shaft. (d) Using an SST, disengage the steering wheel. SST ( , , , ) CAUTION: Apply a small amount of grease to the thread portion and end portion of the center bolt of the SST. (e) Remove the SST and nut, and then detach the steering wheel. 17

18 10. REMOVE STEERING COLUMN COVER (a) Remove the 2 screws. (b) Disengage the 2 claws and remove the lower column cover. (c) Disengage the claw and remove the upper cover. 11. REMOVE SPIRAL CABLE SUB-ASSEMBLY (a) Disconnect the connectors. (b) Disengage the claw at the 3 locations, and then remove the spiral cable. (c) Mark and store the removed spiral cable in a separate container so as not to be reinstalled in error. 18

19 G. INSTALL SPIRAL CABLE CAUTION: DO NOT break/snap off the lock pin until just installing the steering wheel. Otherwise, the center position of a new spiral cable will be misaligned. 1. INSTALL NEW SPIRAL CABLE (a) Move the turn signal switch to the OFF position. CAUTION: If the turn signal switch is NOT in the OFF position, the protruding pin of the switch interferes with the spiral cable, which may result in damage to the pin. (b) Engage the 3 claws to fasten the new spiral cable. (c) Reconnect the connectors. 19

20 2. INSTALL STEERING COLUMN COVER (a) Engage the claw to fasten the upper column cover. (b) Engage the 2 screws to fasten the lower column cover. (c) Attach and tighten the 2 screws. (d) Check that neither any gap nor looseness is present in the column covers. 20

21 3. REMOVE LOCK PIN FROM SPIRAL CABLE (a) Snap the lock pin (orange) off the new spiral cable. NOTE: There is no problem even if the lock pin is pulled out without separation. (b) Check that the part of the lock pin staying in the new spiral cable has not jut out from the surface. (c) If the part of the lock pin has jut out, push it in. 21

22 NOTE: If the spiral cable was rotated and the center position has been misaligned, perform the following procedure. (1) Using a finger, gently turn the spiral cable counterclockwise until it stops. CAUTION: DO NOT rotate the spiral cable holding the wire harness or connector. (2) Return the spiral cable 2.5 turns clockwise to align the matchmarks. 4. CHECK SPIRAL CABLE CENTER POSITION (a) With the matchmarks aligned, check that the orange (or yellow) roller can be seen through the sight window. NOTE: If the orange (or yellow) roller can be viewed from the sight window, misalignment of the matchmarks is acceptable. 22

23 5. REINSTALL STEERING WHEEL ASSEMBLY (a) While aligning the matchmarks, reinstall the steering wheel. (b) Attach and tighten the nut. Specified torque: T = 50 N*m (510 kgf*cm, 37 ft.*lbf) (c) Reconnect the horn wire connector. 6. REINSTALL HORN BUTTON ASSEMBLY (a) Reconnect the horn connector to the horn button. (b) Reconnect the 2 airbag connectors and securely lock them. CAUTION: Be careful of the connector colors when reconnecting. 23

24 (c) Reinstall the horn button to the steering wheel. (d) While holding the horn button by hand, tighten the 2 bolts with a "TORX" socket (T30). Specified torque: T = 8.8 N*m (90 kgf*cm, 78 in.*lbf) 7. REINSTALL LOWER No.3 AND No.2 STEERING WHEEL COVER (a) Engage the claw and reinstall the cover. (b) Do the same for the other cover. 8. RECONNECT CABLE TO NEGATIVE BATTERY TERMINAL 24

25 9. INSPECT SRS WARNING LIGHT (a) Check that the SRS warning light comes on when the ignition switch is turned on. (b) Check that the warning light will go off when about 6 seconds have elapsed after the ignition switch is turned on. (c) If the warning light does not come on or remains on, check if DTCs have occurred. 10. CHECK THAT HORN, WIPERS AND LIGHTS OPERATE PROPERLY 11. INITIALIZE STEERING ANGLE SENSOR NEUTRAL (ZERO) POINT (a) On a level ground, start the engine, and turn the steering wheel left and right as far as it can go. 12. CHECK STRAIGHT AHEAD POSITION FOR STEERING WHEEL (a) Check that the front wheels are in the straight ahead position when the steeling wheel is in the center position. 13. CHECK FOR DTCS 14. RESTORE SYSTEM SETTINGS AFTER BATTERY RECONNECTION 15. RETURN STEERING COLUMN TILT AND TELESCOPING POSITIONS 25

TECHNICAL INSTRUCTIONS

TECHNICAL INSTRUCTIONS TECHNICAL INSTRUCTIONS RAV4 SPIRAL CABLE SUB-ASSEMBLY REPLACEMENT 1. OPERATION FLOW CHART --------------------------------- 3 2. IDENTIFICATION OF AFFECTED VEHICLES ---------- 4 3. PREPARATION --------------------------------------------------

More information

TECHNICAL INSTRUCTIONS

TECHNICAL INSTRUCTIONS TECHNICAL INSTRUCTIONS DOOR SIDE AIRBAG SENSOR REPLACEMENT RX450h / RX350 / RX200t RX450h/RX350/RX200t Fr ドアエアバッグセンサ交換 一般 _v2.0 1 OPERATION FLOWCHART... 3 2 IDENTIFICATION OF AFFECTED VEHICLES... 4 3 PREPARATION...

More information

TECHNICAL INSTRUCTIONS

TECHNICAL INSTRUCTIONS TECHNICAL INSTRUCTIONS REPLACEMENT THE STEERING INTERMEDIATE SHAFT ASSEMBLY FJ CRUISER For LHD 1 OPERATION FLOWCHART... 3 2 IDENTIFICATION OF AFFECTED VEHICLES... 4 3 PREPARATION... 5 4 GENERAL DESCRIPTION...

More information

TECHNICAL INSTRUCTIONS

TECHNICAL INSTRUCTIONS TECHNICAL INSTRUCTIONS ES350 / ES250 / ES200 BRAKE ACTUATOR ASSEMBLY REPLACEMENT 1. OPERATION FLOW CHART --------------------------------- 3 2. IDENTIFICATION OF AFFECTED VEHICLES ---------- 4 3. PREPARATION

More information

TECHNICAL INSTRUCTIONS

TECHNICAL INSTRUCTIONS TECHNICAL INSTRUCTIONS GS460 (for LHD) REPLACEMENT OF FUEL PRESSURE SENSOR GASKET 1. OPERATION FLOW CHART --------------------------------- 3 2. IDENTIFICATION OF AFFECTED VEHICLES ---------- 4 3. PREPARATION

More information

TECHNICAL INSTRUCTIONS FRONT WIPER ARM NUTS REPLACEMENT

TECHNICAL INSTRUCTIONS FRONT WIPER ARM NUTS REPLACEMENT TECHNICAL INSTRUCTIONS RECALL CAMPAIGN SPECIAL SERVICE CAMPAIGN FRONT WIPER ARM NUTS REPLACEMENT IS250, IS300, IS350, IS200d, IS220d, IS250C, IS300C, IS350C IS F 1. OPERATION FLOW CHART ---------------------------------

More information

TECHNICAL INSTRUCTIONS

TECHNICAL INSTRUCTIONS TECHNICAL INSTRUCTIONS LS600hL/LS600h (for LHD) REPLACEMENT OF FUEL PRESSURE SENSOR GASKET 1. OPERATION FLOW CHART --------------------------------- 3 2. IDENTIFICATION OF AFFECTED VEHICLES ----------

More information

ALLDATA Online Toyota Truck Tacoma 4WD V6-4.0L (1GR-FE) - Service and... Service and Repair 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

ALLDATA Online Toyota Truck Tacoma 4WD V6-4.0L (1GR-FE) - Service and... Service and Repair 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL Page 1 of 9 Service and Repair FRONT WIPER MOTOR REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WIPER ARM HEAD CAP a. Using a screwdriver wrapped with protective tape, remove

More information

SCION tc 2005 LEATHER STEERING WHEEL Preparation. Part Number: (Silver/Dark Gray)

SCION tc 2005 LEATHER STEERING WHEEL Preparation. Part Number: (Silver/Dark Gray) Preparation Part Number: 08460 21810 (Silver/Dark Gray) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Reqd. Description 1 1 Steering Wheel

More information

TECHNICAL INSTRUCTIONS

TECHNICAL INSTRUCTIONS TECHNICAL INSTRUCTIONS AURIS AURIS HYBRID COROLLA RUKUS ZELAS REPLACEMENT OF FUEL SUCTION PLATE 1. OPERATION FLOW CHART --------------------------------- 3 2. IDENTIFICATION OF AFFECTED VEHICLES ----------

More information

FUEL SYSTEM PRECAUTION FU 1

FUEL SYSTEM PRECAUTION FU 1 2GR-FE EL EL SYSTEM EL SYSTEM PRECAUTION 1 1. EXPRESSIONS OF IGNITION SWITCH (a) The type of the ignition switch used on this model differs according to the specifications of the vehicle. The expressions

More information

STEERING SYSTEM PRECAUTION SR 1

STEERING SYSTEM PRECAUTION SR 1 System Name Power Window Control System STEERING COLUMN STEERING SYSTEM STEERING SYSTEM PRECAUTION 1 1. HANDLING PRECAUTIONS FOR S AIRBAG SYSTEM (SEE PAGE RS-1) 2. HANDLING PRECAUTIONS FOR STEERING COLUMN

More information

Rear Door: Service and Repair REAR DOOR

Rear Door: Service and Repair REAR DOOR 2007 Toyota Matrix L4-1.8L (1ZZ-FE) Copyright 2013, ALLDATA 10.52 Page 1 Rear Door: Service and Repair REAR DOOR Rear Door 2007 Toyota Matrix L4-1.8L (1ZZ-FE) Copyright 2013, ALLDATA 10.52 Page 2 ISASSEMBLY

More information

2004 Lexus LS430. Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS

2004 Lexus LS430. Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS 2004 Lexus LS430 Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS OVERHAUL If the airbag connector is disconnected with the ignition switch in the ON position, DTCs will be recorded. When

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS 1 DESCRIPTION: 2 APPLICATION: 3 PART NUMBER(S) REQUIRED FOR INSTALLATION: Fog Lamp Kit (AL) Rogue (SV) 999F1 G2000 (Fog Lamp Kit) 4 KIT CONTENTS: Item Qty. Part

More information

The driver side squib circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad.

The driver side squib circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad. Page 1 of 19 DTC B1800/51 SHORT IN DRIVER SIDE SQUIB CIRCUIT; DTC B1801/51 OPEN IN DRIVER SIDE SQUIB CIRCUIT; DTC B1802/51 SHORT TO GND IN DRIVER SIDE SQUIB CIRCUIT; DTC B1803/51 SHORT TO B+ IN DRIVER

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS 1 DESCRIPTION: 2 APPLICATION: 3 PART NUMBER(S) REQUIRED FOR INSTALLATION: Fog Lamp Kit Rogue w/ AL 999F1 G2000 (Fog Lamp Kit) 4 KIT CONTENTS: Item Qty. Part Description

More information

TECHNICAL INSTRUCTIONS FOR SAFETY RECALL E0G SUB HARNESS (FILTER) INSTALLATION

TECHNICAL INSTRUCTIONS FOR SAFETY RECALL E0G SUB HARNESS (FILTER) INSTALLATION TECHNICAL INSTRUCTIONS FOR SAFETY RECALL E0G SUB HARNESS (FILTER) INSTALLATION 2003 2004 MODEL YEAR AVALON COLUMN MOUNTED SHIFT LEVER (FRONT BENCH SEAT) All dealership associates involved in the recall

More information

GENUINE FOG LIGHT INSTALLATION AND USER S INSTRUCTIONS

GENUINE FOG LIGHT INSTALLATION AND USER S INSTRUCTIONS GENUINE FOG LIGHT INSTALLATION AND USER S INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the

More information

ARTICLE BEGINNING SERVICE PRECAUTIONS

ARTICLE BEGINNING SERVICE PRECAUTIONS Page 1 of 96 ARTICLE BEGINNING SERVICE PRECAUTIONS WARNING: WARNING: CAUTION: When performing any inspection or service procedure on this vehicle, ensure following service precautions are followed to prevent

More information

WIPER AND WASHER SYSTEM

WIPER AND WASHER SYSTEM WIPER AND WASHER WIPER AND WASHER SYSTEM WIPER AND WASHER SYSTEM PRECAUTION 1 NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the cable

More information

Telescopic Lever Detent Clip Replacement

Telescopic Lever Detent Clip Replacement T-SB-0147-13 September 27, 2013 Service Category Steering Section Steering Column Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 2012 Avalon SUPERSESSION NOTICE The information contained

More information

SRS AIRBAG SECTION SR CONTENTS RESTRAINTS SR-1 PRECAUTION... 2 PREPARATION... 4 REMOVAL AND INSTALLATION... 5

SRS AIRBAG SECTION SR CONTENTS RESTRAINTS SR-1 PRECAUTION... 2 PREPARATION... 4 REMOVAL AND INSTALLATION... 5 RESTRAINTS SECTION SR A SRS AIRBAG B C D CONTENTS E PRECAUTION... 2 PRECAUTIONS... 2 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN- SIONER"...2 Precaution Necessary

More information

TOYOTA YARIS XM SATELLITE RADIO Preparation (Sedan & Hatchback)

TOYOTA YARIS XM SATELLITE RADIO Preparation (Sedan & Hatchback) Preparation (Sedan & Hatchback) Part Number: Mounting Kit PT546-52096 Tuner Assy 86180-0W031 Tuner Assy Kit Contents (86180-0W031) Item # Quantity Reqd. Description 1 1 Tuner Assy, Stereo Component Mounting

More information

STEERING COLUMN SWITCHES

STEERING COLUMN SWITCHES STEERING COLUMN SWITCHES 1994 Toyota Celica 1994 ACCESSORIES & EQUIPMENT Toyota Motor Sales, U.S.A., Inc. - Steering Column Switches Celica * PLEASE READ THIS FIRST * WARNING: Are equipped with a driver-side

More information

1. General Description

1. General Description General Description 1. General Description A: COMPONENT (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (24) (23) (22) (21) (20) (19) (18) (17) (16) (15) (14) (13) (12) (11) AB-02007 (1) Curtain airbag module

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory TRIM Application 2009 ACCORD 4-DOOR Publications No. AII 40008 Issue Date JULY 2008 PARTS LIST Steering Wheel Trim (Without Navigation) P/N 08Z13-TA0-100 Right steering

More information

TECHNICIAN SAFETY INFORMATION

TECHNICIAN SAFETY INFORMATION 2009 Honda Accord L4-2.4L Vehicle > Restraints and Safety Systems > Air Bag Systems > Service Precautions TECHNICIAN SAFETY INFORMATION SRS Precautions and Procedures General Precautions NOTE: Some systems

More information

SRS AIRBAG Toyota RAV4. Supplemental Restraint System - RAV4 PRECAUTION CAUTION:

SRS AIRBAG Toyota RAV4. Supplemental Restraint System - RAV4 PRECAUTION CAUTION: 2005 RESTRAINTS Supplemental Restraint System - RAV4 SRS AIRBAG PRECAUTION CAUTION: The TOYOTA RAV4 is equipped with SRS that includes a driver airbag, front passenger airbag, side airbag and curtain shield

More information

INTEGRATION MODULE HARNESS KIT A4, F4

INTEGRATION MODULE HARNESS KIT A4, F4 GENUINE INTEGRATION MODULE HARNESS KIT A4, F4 INSTALLATION INSTRUCTIONS Vehicle: Mazda MX-5 Parts numberbbm2 79 CFZ (ipod integration module) C9FA V6 029 (Harness Kit A4) C9FB V6 029 (Harness Kit F4) Thank

More information

STEERING COLUMN - TILT

STEERING COLUMN - TILT STEERING COLUMN - TILT 1993 Toyota Celica 1993 STEERING Toyota - Steering Columns - Tilt Wheel Celica DESCRIPTION & OPERATION Tilt steering wheels incorporate an upper steering shaft, attached by a "U"

More information

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

SUPPLEMENTAL RESTRAINT SYSTEM (SRS) 52B-1 SUPPLEMENTAL RESTRAINT SYSTEM (SRS) CONTENTS GENERAL INFORMATION................ 2 SRS SERVICE PRECAUTIONS........... 3 SPECIAL TOOLS........................ 5 TEST EQUIPMENT......................

More information

SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM SEAT BELT SEAT BELT WARNING SYSTEM 1 SEAT BELT WARNING SYSTEM System Name Power window control system (with Jam Protection Function) Sliding Roof System PRECAUTION When disconnecting the cable from the

More information

STEERING COLUMN - TILT

STEERING COLUMN - TILT STEERING COLUMN - TILT 1994 Toyota Celica 1994 STEERING Toyota - Steering Column - Tilt Wheel Celica DESCRIPTION & OPERATION Tilt steering wheels incorporate a mainshaft, attached by a "U" joint to an

More information

INSTRUCCIONES TECNICAS DE CAMPAÑA TUNDRA

INSTRUCCIONES TECNICAS DE CAMPAÑA TUNDRA INSTRUCCIONES TECNICAS DE CAMPAÑA TUNDRA PARA AIRBAG DE CORTINA I. OPERATION FLOW CHART Verify Vehicle Eligibility 1. Check the VIN range. 2. Check the TIS Vehicle Inquiry System. Not Covered No further

More information

DESCRIPTION & OPERATION

DESCRIPTION & OPERATION AIR BAG RESTRAINT SYSTEM 1996 ACCESSORIES/SAFETY EQUIPMENT Toyota Air Bag Restraint System DESCRIPTION & OPERATION WARNING: To avoid injury from accidental air bag deployment, read and carefully follow

More information

(a) Remove the rear floor service hole cover. (b) Disconnect the fuel pump connector.

(a) Remove the rear floor service hole cover. (b) Disconnect the fuel pump connector. REMOVAL 1. REMOVE REAR SEAT CUSHION ASSEMBLY 2. REMOVE REAR FLOOR SERVICE HOLE COVER (a) Remove the rear floor service hole cover. (b) Disconnect the fuel pump connector. 3. DISCHARGE FUEL SYSTEM PRESSURE

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory P/N 08U97-TX4-200 Application 2016 RDX Publications No. VERSION 1 Issue Date APRIL 2015 PARTS LIST Steering wheel Illustration of the Steering Wheel in the Vehicle 2

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 23302 2002 MDX Issue Date PN 08U97-S3V-210 (BLACK) P/N 08U97-S3V-270 (SADDLE) NOV 2001 PARTS LIST Wood trim steering wheel 1. Make sure

More information

GENUINE FOG LIGHT BEZEL

GENUINE FOG LIGHT BEZEL GENUINE FOG LIGHT BEZEL INSTALLATION INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the contents

More information

SUPPLEMENTAL RESTRAINT SYSTEM

SUPPLEMENTAL RESTRAINT SYSTEM PRECAUTION CAUTION: PRIUS is equipped with SRS, which consists of a driver airbag, front passenger airbag, side airbag and curtain shield airbag. Failure to carry out service operations in the correct

More information

TECHNICAL INSTRUCTIONS FOR SAFETY RECALL C0T STEERING INTERMEDIATE EXTENSION SHAFT 2004 CERTAIN 2009 MODEL YEAR PRIUS

TECHNICAL INSTRUCTIONS FOR SAFETY RECALL C0T STEERING INTERMEDIATE EXTENSION SHAFT 2004 CERTAIN 2009 MODEL YEAR PRIUS TECHNICAL INSTRUCTIONS FOR SAFETY RECALL C0T STEERING INTERMEDIATE EXTENSION SHAFT 2004 CERTAIN 2009 MODEL YEAR PRIUS I. OPERATION FLOW CHART II. IDENTIFICATION OF AFFECTED VEHICLES A. COVERED VIN RANGE

More information

REPAIR INSTRUCTION PRECAUTION. 1. BASIC REPAIR HINT (a) HINTS ON OPERATIONS

REPAIR INSTRUCTION PRECAUTION. 1. BASIC REPAIR HINT (a) HINTS ON OPERATIONS 015 PRECAUTION 1. BASIC REPAIR HINT (a) HINTS ON OPERATIONS 010DR01 2 1 3 6 5 4 D25016 1 Looks Always wear a clean uniform. Hat and safety shoes must be worn. 2 Vehicle protection Set a grill cover, fender

More information

The steering column is of a modular construction and features easy to service electrical switches.

The steering column is of a modular construction and features easy to service electrical switches. file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a01.htm~gen~ref.htm Page 1 of 3 Section 11-04A: Steering Column, Ranger DESCRIPTION AND OPERATION 1997 Ranger Workshop Manual Steering Column NOTE:

More information

TOYOTA RAV TRAILER WIRE HARNESS Section I Installation Preparation

TOYOTA RAV TRAILER WIRE HARNESS Section I Installation Preparation Section I Installation Preparation Part Number: 08921-42900 Kit Contents Item # Quantity Reqd. Description 1 1 Converter 2 1 Wire harness 3 1 Sub wire harness No.1 4 2 Plastic Tie (300mm) 5 21 Plastic

More information

2004 Toyota RAV ACCESSORIES/SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems

2004 Toyota RAV ACCESSORIES/SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems DESCRIPTION & OPERATION 2004 ACCESSORIES/SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems WARNING: Accidental air bag deployment is possible. Personal injury may result. Read and follow all WARNINGS

More information

Airbags, servicing. Airbag system, safety precautions WARNING!

Airbags, servicing. Airbag system, safety precautions WARNING! Page 1 of 75 69-40 Airbags, servicing Airbag system, safety precautions Checking, removing, installing and servicing may ONLY be performed by qualified personnel. Never perform tests using a test light

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 37248 2008 TSX Issue Date JUNE 2007 PARTS LIST 1. Make sure you have the anti-theft code for the radio, then write down the frequencies

More information

VENTILATION SYSTEM SECTION VTL CONTENTS VENTILATION, HEATER & AIR CONDITIONER VTL-1 FUNCTION DIAGNOSIS... 3 PRECAUTION... 6 PREPARATION...

VENTILATION SYSTEM SECTION VTL CONTENTS VENTILATION, HEATER & AIR CONDITIONER VTL-1 FUNCTION DIAGNOSIS... 3 PRECAUTION... 6 PREPARATION... VENTILATION, HEATER & AIR CONDITIONER SECTION VTL A VENTILATION SYSTEM B C D CONTENTS E FUNCTION DIAGNOSIS... 3 AUTOMATIC AIR CONDITIONER SYSTEM... 3 WITH COLOR DISPLAY...3 WITH COLOR DISPLAY : Switches

More information

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

SUPPLEMENTAL RESTRAINT SYSTEM (SRS) RESTRAINTS SECTION SRS A SUPPLEMENTAL RESTRAINT SYSTEM (SRS) B C D CONTENTS E PRECAUTION... 2 PRECAUTIONS... 2 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN- SIONER"...2

More information

VENTILATION SYSTEM SECTION VTL CONTENTS VENTILATION, HEATER & AIR CONDITIONER VTL-1 PRECAUTION... 3 PREPARATION... 5 SYSTEM DESCRIPTION...

VENTILATION SYSTEM SECTION VTL CONTENTS VENTILATION, HEATER & AIR CONDITIONER VTL-1 PRECAUTION... 3 PREPARATION... 5 SYSTEM DESCRIPTION... VENTILATION, HEATER & AIR CONDITIONER SECTION VTL A VENTILATION SYSTEM B C D CONTENTS E PRECAUTION... 3 PRECAUTIONS... 3 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN-

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory WOODGRAIN LOOK P/N 08U97-TZ5-200 Application 2014 MDX Publications No. BII 48844-49638 Issue Date JUNE 2013 PARTS LIST INSTALLATION Steering wheel 2 TORX bolts Steering

More information

ARTICLE BEGINNING DESCRIPTION DISABLING & ACTIVATING AIR BAG SYSTEM SERVICE PRECAUTIONS STEERING Volkswagen - Steering Columns.

ARTICLE BEGINNING DESCRIPTION DISABLING & ACTIVATING AIR BAG SYSTEM SERVICE PRECAUTIONS STEERING Volkswagen - Steering Columns. Article Text ARTICLE BEGINNING 1995-96 STEERING Volkswagen - Steering Columns Golf III WARNING: All models are equipped with a Supplemental Restraint System (SRS) that includes an air bag located in steering

More information

GENUINE FOG LAMP KIT

GENUINE FOG LAMP KIT GENUINE FOG LAMP KIT Using (Installation) Instructions Applicable model : MAZDA CX-7 Part Number : ER18 V4 600 (small tank) ER19 V4 600 (large tank) Thank you very much for buying the Mazda Genuine Parts.

More information

VENTILATION SYSTEM SECTION VTL CONTENTS VENTILATION, HEATER & AIR CONDITIONER VTL-1 SYSTEM DESCRIPTION... 3 PRECAUTION... 6 PREPARATION...

VENTILATION SYSTEM SECTION VTL CONTENTS VENTILATION, HEATER & AIR CONDITIONER VTL-1 SYSTEM DESCRIPTION... 3 PRECAUTION... 6 PREPARATION... VENTILATION, HEATER & AIR CONDITIONER SECTION VTL A VENTILATION SYSTEM B C D CONTENTS E SYSTEM DESCRIPTION... 3 AUTOMATIC AIR CONDITIONER SYSTEM... 3 WITH COLOR DISPLAY...3 WITH COLOR DISPLAY : Switches

More information

Water Leak in 3rd Row Seat Stow Area

Water Leak in 3rd Row Seat Stow Area T-SB-0214-12 November 1, 2012 Service Category Vehicle Exterior Section Exterior Panels/Trim Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2011 2012 Sienna Introduction Some 2011 2012

More information

ED 42. ENGINE HOOD / DOOR FRONT DOOR (w/o Power Window)

ED 42. ENGINE HOOD / DOOR FRONT DOOR (w/o Power Window) 42 ENGINE HOOD / DOOR FRONT DOOR (w/o Power Window) (g) (h) Horizontally and vertically adjust the door by loosening the door side hinge bolts. Tighten the door side hinge bolts after the adjustment. Torque:

More information

STEERING COLUMN - STANDARD

STEERING COLUMN - STANDARD STEERING COLUMN - STANDARD 1994 Toyota Celica 1994 STEERING Toyota - Steering Column - Standard Celica DESCRIPTION & OPERATION Steering column is a collapsible 2-piece design. Columns use shear pins to

More information

TOYOTA Yaris Hatchback EC REARVIEW MIRROR Preparation

TOYOTA Yaris Hatchback EC REARVIEW MIRROR Preparation Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description

More information

Part Number: PT

Part Number: PT Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description

More information

TOYOTA COROLLA EC REARVIEW MIRROR Preparation

TOYOTA COROLLA EC REARVIEW MIRROR Preparation Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,

More information

SUPPLEMENTAL RESTRAINT SYSTEM

SUPPLEMENTAL RESTRAINT SYSTEM PRECAUTION CAUTION: HIGHLANDER is equipped with SRS, which consists of a driver airbag, front passenger airbag, side airbag and curtain shield airbag. Failure to carry out service operations in the correct

More information

Safety Recall Remedy Toyota dealers are requested to replace the Steering Column Upper Bracket at NO CHARGE to the vehicle owner.

Safety Recall Remedy Toyota dealers are requested to replace the Steering Column Upper Bracket at NO CHARGE to the vehicle owner. To: Subject: All Toyota Dealer Principals, Service Managers, Parts Managers Voluntary Safety Recall A0H Certain 2000 through 2004 Toyota Avalon Steering Column Upper Bracket Replacement As communicated

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS [1] Description: Tow Hitch Wire Harness Kit [2] Application: Nissan Rogue Note: Tow Harness application is limited to specific vehicle option packages that include tow harness

More information

TECHNICAL INSTRUCTIONS FOR SAFETY RECALL D0H BRAKE BOOSTER PUMP ASSEMBLY (ACCUMULATOR) CERTAIN 2010 MODEL YEAR PRIUS

TECHNICAL INSTRUCTIONS FOR SAFETY RECALL D0H BRAKE BOOSTER PUMP ASSEMBLY (ACCUMULATOR) CERTAIN 2010 MODEL YEAR PRIUS TECHNICAL INSTRUCTIONS FOR SAFETY RECALL D0H BRAKE BOOSTER PUMP ASSEMBLY (ACCUMULATOR) CERTAIN 2010 MODEL YEAR PRIUS Complete D0H Technical Video Supplement I. OPERATION FLOW CHART The flow chart is for

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 24570 P/N 08U97-S3V-210A (BLACK) P/N 08U97-S3V-220A(SADDLE) 2003 MDX Issue Date OCT 2002 PARTS LIST Wood steering wheel 1. Make sure

More information

SUSPENSION SYSTEM PROBLEM SYMPTOMS TABLE SP 1

SUSPENSION SYSTEM PROBLEM SYMPTOMS TABLE SP 1 SUENSION SUENSION SYSTEM 1 SUENSION SYSTEM Suspension system Vehicle is unstable Bottoming Sways/pitches Wheels shimmy Abnormal tire wear Vehice pull PROBLEM SYMPTOMS TABLE Use the table below to help

More information

TECHNICAL INSTRUCTIONS FOR SAFETY RECALL ALE VALVE SPRING AND LASH ADJUSTER REPLACEMENT GS 350: IS 350:

TECHNICAL INSTRUCTIONS FOR SAFETY RECALL ALE VALVE SPRING AND LASH ADJUSTER REPLACEMENT GS 350: IS 350: TECHNICAL INSTRUCTIONS FOR SAFETY RECALL ALE VALVE SPRING AND LASH ADJUSTER REPLACEMENT GS 350: 2007 2008 IS 350: 2006 2008 I. OPERATION FLOWCHART Verify Vehicle Eligibility 1. Check the VIN range. 2.

More information

GENUINE STRUT TOWER BAR

GENUINE STRUT TOWER BAR GENUINE STRUT TOWER BAR INSTALLATION AND USER S INSTRUCTIONS Please check for compliance with local law prior to purchase and installation of this device. Thank you for purchasing a genuine Mazda accessory.

More information

TOYOTA TUNDRA TVIP V4 REMOTE ENGINE STARTER (RES)

TOYOTA TUNDRA TVIP V4 REMOTE ENGINE STARTER (RES) Preparation Part Number: 08586-OC910 Conflicts Do not install into vehicles without RKE systems. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM Radio NOTE:

More information

POWER STEERING TO INDEX POWER STEERING SYSTEM PRECAUTIONS... OPERATION CHECK... PROBLEM SYMPTOMS TABLE... VANE PUMP ASSEMBLY COMPONENTS...

POWER STEERING TO INDEX POWER STEERING SYSTEM PRECAUTIONS... OPERATION CHECK... PROBLEM SYMPTOMS TABLE... VANE PUMP ASSEMBLY COMPONENTS... TO INDEX STEERING POWER STEERING POWER STEERING SYSTEM PRECAUTIONS.............................................. OPERATION CHECK......................................... PROBLEM SYMPTOMS TABLE.................................

More information

FOR ALL OF VEHICLES PRECAUTION

FOR ALL OF VEHICLES PRECAUTION INTRODUCTION PRECAUTION IN9 1. FOR VEHICLES EQUIPPED WITH SRS AIRBAG (a) The 4RUNNER is equipped with an SRS (Supplemental Restraint System), such as the driver airbag, front passenger airbag and seat

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL ENGINE STARTER Application 2010 CR-V Publications No. AII 42612-42916 Issue Date OCT 2009 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-101B

More information

TOYOTA HIGHLANDER w/o Smart Key TVIP V4 REMOTE ENGINE STARTER (RES)

TOYOTA HIGHLANDER w/o Smart Key TVIP V4 REMOTE ENGINE STARTER (RES) Preparation Part Number: PT398-48111 Conflicts Do not install into vehicles without RKE systems. Recommended Sequence of Application Item # Accessory Kit Contents Item # Quantity Description 1 1 Wire Harness

More information

Page 1 of 25. Service and Repair REMOVAL SIZED FOR PRINT. Related Components

Page 1 of 25. Service and Repair REMOVAL SIZED FOR PRINT. Related Components Page 1 of 25 Service and Repair REMOVAL Related Components Page 2 of 25 1ZZ-FE Page 3 of 25 2ZZ-GE 1. REMOVE UPPER FRONT FENDER APRON SEAL AND UPPER RADIATOR SUPPORT SEAL 2. DRAIN ENGINE COOLANT 3. REMOVE

More information

FOR ALL OF VEHICLES PRECAUTION

FOR ALL OF VEHICLES PRECAUTION IN10 PRECAUTION IN0FA01 1. FOR VEHICLES EQUIPPED WITH SRS AIRBAG AND SEAT BELT PRETENSIONER (a) The CELICA is equipped with an SRS (Supplemental Restraint System), such as the driver airbag, front passenger

More information

TOYOTA TUNDRA TVIP V4 Preparation

TOYOTA TUNDRA TVIP V4 Preparation Preparation Part Number: PT398-00100 PT398-00100-AA Conflicts Do not install into vehicles without RKE system. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 25831-26975 P/N 08U97-S3V-210A (BLACK) P/N 08U97-S3V-220A(SADDLE) 2004 MDX Issue Date MARCH 2004 PARTS LIST Wood steering wheel 1. Make

More information

ACCELERATOR CONTROL SYSTEM

ACCELERATOR CONTROL SYSTEM ENGINE SECTION ACC A ACC C D CONTENTS E PRECAUTION... 2 PRECAUTIONS... 2 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN- SIONER"...2 Precautions Necessary for Steering

More information

TOYOTA COROLLA ILLUMINATED DOOR SILLS Preparation

TOYOTA COROLLA ILLUMINATED DOOR SILLS Preparation Preparation Part Number: PT942-02140 Kit Contents Item # Quantity Reqd. Description 1 1 Illuminated Scuff plate, Front Right Hand 2 1 Illuminated Scuff plate, Front Left Hand 3 1 Door Scuff plate, Rear

More information

SCION xb EC REARVIEW MIRROR Preparation

SCION xb EC REARVIEW MIRROR Preparation Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,

More information

TOYOTA HIGHLANDER w/smart Key TVIP V4 REMOTE ENGINE STARTER (RES) Part Number: PT

TOYOTA HIGHLANDER w/smart Key TVIP V4 REMOTE ENGINE STARTER (RES) Part Number: PT Preparation Part Number: PT398-48083 Conflicts Do not install into vehicles without RKE systems. Will not program with Techstream Lite. Recommended Sequence of Application Item # Accessory Kit Contents

More information

SCION xb AUTO-DIMMING MIRROR Preparation

SCION xb AUTO-DIMMING MIRROR Preparation Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,

More information

Dear Customers. : i MiEV INSTRUMENT PANEL ILLUMINATION INSTALLATION AND HANDLING INSTRUCTIONS. Attention

Dear Customers. : i MiEV INSTRUMENT PANEL ILLUMINATION INSTALLATION AND HANDLING INSTRUCTIONS. Attention Dear Customers Thank you for purchasing a Mitsubishi genuine optional part. For proper use of the product, please read this leaflet thoroughly. It is recommended you keep this leaflet at hand for future

More information

Remote engine start INSTALLATION INSTRUCTIONS

Remote engine start INSTALLATION INSTRUCTIONS GENUINE Remote engine start INSTALLATION INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. efore removal and installation, be sure to thoroughly read these instructions. Please read the

More information

* * APPLICABLE MODELS: 2014 > Mazda 3

* * APPLICABLE MODELS: 2014 > Mazda 3 PART NUMBER: 0000 8C L48 (DIO) / 0000 89 L84 (PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0700-000* APPLICABLE MODELS: 2014 > Mazda 3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage

More information

Power Steering Rack Leak from Right Side: Overhaul Procedure

Power Steering Rack Leak from Right Side: Overhaul Procedure T-SB-0030-14 April 17, 2014 Power Steering Rack Leak from Right Side: Overhaul Procedure Service Category Steering Section Steering Gear/Linkage Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION

More information

Multi-Function Switch

Multi-Function Switch 1 of 9 Nissan Frontier, Xterra 1998-05 Multi-Function Switch REMOVAL & INSTALLATION Fig. Multi-function switch component locations 1998-2000-2000 shown Before servicing, or working around, the SRS system,

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL Application 2008 CR-V Publications No. AII 35843-38422 Issue Date DEC 2007 PARTS LIST Caution label Remote Engine Starter Kit P/N 08E91-E22-100B Transmitter

More information

Product Campaign Bulletin

Product Campaign Bulletin Nissan Ireland Cedar House Park West Business Park Nangor Road, Dublin 12 Product Campaign Bulletin REFERENCE: MODEL: PCB-NES-12-052 J10 & J10+2 Qashqai SUBJECT: PCB J10 - PG2B9 and PS2B7- Steering wheel

More information

* * APPLICABLE MODELS: 2014 > Mazda 6

* * APPLICABLE MODELS: 2014 > Mazda 6 PART NUMBER: 0000 8C H02(DIO) / 0000 89 H18(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0694-000* APPLICABLE MODELS: 2014 > Mazda 6 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL Application 2014 TSX (L4) Publications No. BII 50198 Issue Date SEPT 2013 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-TK4-200A Fuse label Transmitter

More information

GENUINE FOG LAMP KIT

GENUINE FOG LAMP KIT GENUINE FOG LAMP KIT Using (Installation) Instructions Applicable model:mazda CX-5 Part number:kd33 V4 600 Thank you very much for buying the Mazda Genuine Parts. Before removal and installation, you are

More information

TOYOTA PRIUS XM SATELLITE RADIO Preparation

TOYOTA PRIUS XM SATELLITE RADIO Preparation Preparation Part Number: Mounting Kit PT546-4700 Tuner Assy 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item # Quantity

More information

TECHNICAL INSTRUCTIONS FOR SAFETY RECALL 90L ACCELERATOR PEDAL MODIFICATION Certain 2009 MODEL YEAR 4RUNNER

TECHNICAL INSTRUCTIONS FOR SAFETY RECALL 90L ACCELERATOR PEDAL MODIFICATION Certain 2009 MODEL YEAR 4RUNNER TECHNICAL INSTRUCTIONS FOR SAFETY RECALL 90L ACCELERATOR PEDAL MODIFICATION 2003 Certain 2009 MODEL YEAR 4RUNNER I. OPERATION FLOW CHART Verify Vehicle Eligibility 1. Check the VIN range. 2. Check the

More information

YEAR(S) MODEL(S) ADDITIONAL INFORMATION

YEAR(S) MODEL(S) ADDITIONAL INFORMATION T-SB-0061-12 April 6, 2012 Service Category Vehicle Interior Section Heating/Air Conditioning Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 2012 Tacoma Introduction In a limited

More information

* * APPLICABLE MODELS: 2017 > CX-5

* * APPLICABLE MODELS: 2017 > CX-5 PART NUMBER: 0000 8C R06(DIO) / 0000 89 R28(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0681-000* APPLICABLE MODELS: 2017 > CX-5 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart

More information

INSTRUCCIONES TECNICAS

INSTRUCCIONES TECNICAS INSTRUCCIONES TECNICAS INSTALACIÓN DEL REFUERZO EN EL PANEL DE ACCESO DEL FJ CRUISER (Traducción al Español Parcialmente) 1. FUNCIONAMIENTO ORGANIGRAMA 3 2. IDENTIFICACIÓN DE VEHÍCULOS AFECTADOS 4 3. PREPARACIÓN

More information

REMOVAL AND REPLACEMENT

REMOVAL AND REPLACEMENT 2005 Scion tc L4-2.4L (2AZ-FE) Vehicle > Powertrain Management > Fuel Delivery and Air Induction > Fuel Pump > Service and Repair REMOVAL AND REPLACEMENT https://my.alldata.com/repair/#/repair/article/39648/component/20/itype/401/nonstandard/

More information