Year of manufacture 2007 Control HEIDENHAIN itnc 530 Machine number X mm / Y mm / Z mm C - +/- 220 / B - +/- 110

Transcription

1 EiMa GAMMA T LINEAR 5 axes portal machining center In excellent conditions Manufacturer Model EiMa GAMMA T LINEAR Year of manufacture 2007 Control HEIDENHAIN itnc 530 Machine number Travels X mm / Y mm / Z mm C - +/- 220 / B - +/- 110 The machine worked less than one-shift and it has only spindle hours KISTNER GmbH & Co. KG Industriestraße Thurnau

2 Model and mould making places its own particular set of demands on a machining centre; This series meets these demands in full including for large-volume aluminium components, ureol or even light HSC steel machining. In these areas too, the proven components of the modular system can be tailored to individual jobs. The linear design in particular brings the user maximum dynamics combined with maximum accuracy thanks to the mechatronically calculated machine concept. The machine has a fully developed chip management system, which impresses with its excellent chip disposal system that incorporates self-cleaning chip baffle plates and insensitive, high quality chip conveyors. EQUIPMENT 5 axes fork type milling head 20 kw Spindle HSK 63 Speed up to rpm 30-slot tool changer in disc-type Machine table x x 90 mm Approx. 20 tool holders HSK 63 Electronic hand wheel HR clamping tables 800 x 500 x 400 mm Extraction system (Manufacturer SARA - Model UCSD-4000) Chip conveyor Band filter system Shrink fit (Manufacturer KELCH - Model i-tec L) User guide / Documentation Machine parameters on storage medium 2 - EiMa GAMMA T LINEAR

3 TECHNICAL DATA and CONFIGURATION Working area X axis Y axis Z axis mm mm mm C axis +/- 220 B axis +/- 110 Distance from the table to the plane of the spindle in the lowest position 100 mm Feed rate X axis Y axis Z axis 60 m/min 60 m/min 40 m/min Machine design Modular machine construction in heavy, torsion-resistant steel construction Y-directional gantry X and Z axis on the gantry for receiving the processing units Y-axis guides on side guides Large-dimensioned, hardened and ground precision linear guides allow highest accuracy and carrying capacity Cast iron machine table Table size incl. 8 T-grooves x x 90 mm DIN H12 / Abstand 150 mm User operation panel consisting of: Control panel with emergency stop, NC-Start, Stop 3 - EiMa GAMMA T LINEAR

4 Band filter system with l tank Filtersurface, approx. 0,4 m 2 Filter performance Filtration efficiency Tank made of 3 mm sheet steel including level indicator, drain plug, float circuit, inlet bell, 100 m filter fleece roll, mud box approx. 50 1/min Emulsion approx. 30 µm, clean tank I Supply pump Supply pump 14 1/min at 3 bar, 400 V, 50 Hz, 0,63 kw, incl. tubing in the machine 1 spray nozzle mounted on 5-axis head, can be switched on and off via M function Suitable for commercial rust-proof drilling emulsions TA 21/300-3 bar, mounted on the filter Irrigation pump Irrigation pump Additional, separate pump with permanent pressure for cleaning the working area with drilling emulsion TC l/min at 4 bar Cartridge filter as a double switching filter As additional filter and emergency filter with clogging indicator 16μm Tapered-bed conveyor KB 400 with reversing switch Total width approx. 440 mm Feed width / feed length approx. 370 mm / approx mm Dropping height mm Pitch EiMa GAMMA T LINEAR

5 Milling spindle 20 kw, with sensor MA-OM 20/26 Spindle for milling, drilling and sawing Grease-lubricated, water-cooled, tool holder HSK 63 F. Suitable for automatic tool change Necessary balancing material for tool holder and tool size 2.5. Max rpm, 75 I 96 A S1 S6 60% S6 40% 20 kw from 6000 rpm, 32 Nm to 6000 rpm 24 kw from 6000 rpm, 35 Nm to 6000 rpm 26 kw from 6000 rpm, 41 Nm to 6000 rpm Driver for torque arm for tools with torque arm, if no vector axis is used Converter 85 / 110 A, O Hz Vibration analysis Vibration sensor for checking the imbalance of the tool spindle system at a certain speed, manufactured by IFM efector octavis. Based on capacitive measuring principle with micro-mechanical acceleration sensor. Compressor cooler BR 15 RFCS-BL-015/1,0/W incl. flow monitor cooling capacity at 32 ambient 2.2 kw Tank capacity 15 l Disc type tool changer 30 places Holder HSK 63 F, max. tool diameter 80 mm at full occupancy Max. tool lenght from plan to milling tip 250 mm Tool dimensions and weights are only the maximum values of the tool changer and have no influence on the bypass area Max. tool weight per seat with complete assignment of the tool changer 5 kg Tool changer with stroke about 400 mm and own guides 5 - EiMa GAMMA T LINEAR

6 Enclosure of the tool changer in a sheet metal housing, loading flap with a small window. Change side with pneumatically controlled cover. The tool changer is completely protected from chips. 5 axes fork milling head with centered spindle max. 20 kw with direct measuring system in the B axis and indirect in the C axis. Turning axis +/- 220, 14 rpm Swiveling axis +/- 110, 20 rpm Suitable for spindles with tool lenght from plan to milling tip max. 180 mm. Longer tools can be used in compliance with the specified noise contours. Reinforced C-axis for aluminum machining or increased accuracy Z-axis in tower design Tower version with reinforced drive The Z-axis in tower design is equipped with a reinforced drive and a more rigid ball screw. Rapid traverse 40 m/min. Machine cover Protection from the front and on both sides, with rear wall. Front with 2 sliding doors with window. Incl. interlock switch. Height mm. Workspace cover above Chip protection for the working area of the machine by covering it with a folding tarpaulin, mechanically detachable for loading the machine table incl. 2 tray lights made of plastic left and right in the machine area Separate seal for doors and cabin for wet machining 6 - EiMa GAMMA T LINEAR

7 Electric cabinet Position: left to the machine The cabinet is connected to the machine by one or more cable protection conduits. This connection is not disconnected for transport. Control HEIDENHAIN itnc 530 CNC control with up to 10 drives Portable electronic hand wheel HR 420 with display 7 - EiMa GAMMA T LINEAR

8 MACHINE PICTURES 8 - EiMa GAMMA T LINEAR

9 9 - EiMa GAMMA T LINEAR

10 10 - EiMa GAMMA T LINEAR

11 FLOOR PLAN 11 - EiMa GAMMA T LINEAR

12 12 - EiMa GAMMA T LINEAR

13 13 - EiMa GAMMA T LINEAR

14 14 - EiMa GAMMA T LINEAR

15 15 - EiMa GAMMA T LINEAR

16 Thank you very much for your interest *We do not guarantee the accuracy and completeness of these documents. We further do not assure any characteristics and qualities. The named machine, which is up for sale, is used.* KISTNER GmbH & Co. KG Industriestraße Thurnau