DIAGNOSIS AND TESTING

Size: px
Start display at page:

Download "DIAGNOSIS AND TESTING"

Transcription

1 Exterior Lighting DIAGNOSIS AND TESTING Visual Inspection Chart Turn Signal and Hazard Lamps Refer to Wiring Diagrams Cell 90 for schematic and Mechanical Electrical connector information. Multifunction switch Smart junction box Hazard lamp switch (SJB) Special Tool(s) Circuitry Bulbs 73III Automotive Meter 105-R0057 or equivalent 3. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step. 4. If the cause is not visually evident, connect the diagnostic tool to the data link connector (DLC) Worldwide Diagnostic System and select the vehicle to be tested from the (WDS) diagnostic tool menu. If the diagnostic tool does Vehicle Communication Module not communicate with the vehicle: (VCM) with appropriate adapters, or equivalent check that the program card is correctly diagnostic tool installed. check the connections to the vehicle. Flex Probe Kit check the ignition switch position. 105-R025B or equivalent 5. If the diagnostic tool still does not communicate with the vehicle, refer to the diagnostic tool operating manual. 6. Carry out the diagnostic tool data link test. If the diagnostic tool responds with: Principles of Operation CAN or ISO circuit fault; all electronic control units no response/not equipped, refer The smart junction box (SJB) monitors the to Section multifunction switch position by sending multiple response/not equipped for SJB, refer to voltage reference signals to the multifunction Section switch. When the multifunction switch is in the LH or RH TURN positions, or the hazard lamp switch System passed, retrieve and record the is engaged, that input signal is routed to ground. continuous diagnostic trouble codes (DTCs), erase the continuous DTCs and carry out the When the SJB receives a request for a turn signal or self-test diagnostics for the SJB. hazard lamps, the SJB supplies voltage to the appropriate turn lamps. 7. If the DTCs retrieved are related to the concern, go to the Smart Junction Box (SJB) Diagnostic Inspection and Verification Trouble Code (DTC) Index. 1. Verify the customer concern. 8. If no DTCs related to the concern are retrieved, 2. Visually inspect the following for obvious signs of mechanical or electrical damage. GO to Symptom Chart. Copyright 2005, Ford Motor Company Last updated: 06/30/2005

2 Exterior Lighting Symptom Chart Symptom Chart Condition Possible Sources Action communication with the Circuitry REFER to Section smart junction box (SJB) The turn signal lamps are Circuitry GO to Pinpoint Test L. inoperative Multifunction switch The turn signal lamps are Circuitry GO to Pinpoint Test M. always on Multifunction switch One turn signal/hazard lamp Circuitry GO to Pinpoint Test N. is inoperative/always on The hazard lamps are Circuitry GO to Pinpoint Test O. inoperative Hazard lamp switch The hazard lamps are always Circuitry GO to Pinpoint Test P. on Hazard lamp switch Pinpoint Tests Pinpoint Test L: The Turn Signal Lamps Are Inoperative rmal Operation The smart junction box (SJB) sends reference signals to the multifunction switch through circuit CLS39 (VT/WH) (LH turn input) and circuit CLS41 (GY/YE) (RH turn input). When the multifunction switch is switched to the LH or RH TURN positions, the voltage signal is routed to ground. When the SJB detects the multifunction switch in the LH or RH TURN position, the SJB sends voltage to the appropriate turn lamps. All the turn lamps are individually wired to the SJB. The timed on/off cycle is determined by the SJB and is set to flash approximately 80 times per minute if both the front and rear turn lamps operate correctly. If an individual turn signal lamp is inoperative, the SJB flashes the remaining turn lamp approximately 160 times per minute. Possible Causes Circuit CLS39 (VT/WH) open Circuit CLS41 (GY/YE) open Multifunction switch L1 L2 PINPOINT TEST L: THE TURN SIGNAL LAMPS ARE INOPERATIVE CHECK FOR CORRECT HIGH BEAM OPERATION Place the headlamp switch in the HEADLAMPS ON position. Place the multifunction switch in the HIGH BEAM position while PLACE the headlamp switch in the OFF observing the high beam headlamps. position. GO to L2. Do the high beams operate correctly? REFER to Headlamps in this section to continue diagnosis of the high beam headlamps. CHECK THE MULTIFUNCTION SWITCH Disconnect: Multifunction Switch C202. GO to L3. Carry out the multifunction switch component test. Refer to Wiring Diagrams Cell 149 for component testing. INSTALL a new multifunction switch. Is the multifunction switch OK? REFER to Section TEST the system for normal operation. (Continued)

3 Exterior Lighting L3 PINPOINT TEST L: THE TURN SIGNAL LAMPS ARE INOPERATIVE (Continued) CHECK CIRCUIT CLS39 (VT/WH) (LH TURN SIGNAL) OR CLS41 (GY/YE) (RH TURN SIGNAL) FOR AN OPEN Disconnect: SJB C2280d. Ignition ON. Measure the resistance between the multifunction switch C202-2 (LH turn lamps), circuit CLS39 (VT/WH), harness side and the SJB C2280d-14, circuit CLS39 (VT/WH), harness side; or between the multifunction switch C202-3 (RH turn lamps), circuit CLS41 (GY/YE), harness side and the SJB C2280d-24, circuit CLS41 (GY/YE), harness side. L4 GO to L4. Is the resistance less than 5 ohms? normal operation. CHECK FOR CORRECT SJB OPERATION Disconnect all the SJB connectors. Check for: INSTALL a new SJB. REFER to Section corrosion TEST the system for normal pushed-out pins operation. Connect all the SJB connectors and make sure they seat correctly. The system is operating correctly at this Operate the system and verify the concern is still present. time. The concern may have been caused Is the concern still present? by a loose or corroded connector. Pinpoint Test M: The Turn Signal Lamps Are Always On rmal Operation The smart junction box (SJB) sends voltage reference signals to the multifunction switch through circuit CLS39 (VT/WH) (LH turn input) and circuit CLS41 (GY/YE) (RH turn input). When the multifunction switch is switched to the LH or RH TURN positions, the voltage signal is routed to ground. When the SJB detects the multifunction switch in the LH or RH TURN position, the SJB sends voltage to the appropriate turn lamps. Possible Causes Circuit CLS39 (VT/WH) short to ground Circuit CLS41 (GY/YE) short to ground Multifunction switch

4 Exterior Lighting M1 M2 PINPOINT TEST M: THE TURN SIGNAL LAMPS ARE ALWAYS ON CHECK THE MULTIFUNCTION SWITCH Disconnect: Multifunction Switch C202. GO to M2. Ignition ON. Do the turn lamps continue to flash on and off? INSTALL a new multifunction switch. REFER to Section CLEAR the DTCs. REPEAT the self-test. CHECK CIRCUIT CLS39 (VT/WH) (LH TURN SIGNAL) OR CIRCUIT CLS41 (GY/YE) (RH TURN SIGNAL) FOR A SHORT TO GROUND Disconnect: SJB C2280d. Measure the resistance between the multifunction switch C202-2 (LH turn lamps), circuit CLS39 (VT/WH), harness side and ground; or between the multifunction switch C202-3 (RH turn lamps), circuit CLS41 (GY/YE), harness side and ground. M3 GO to M3. REPAIR the circuit. CLEAR the DTCs. Is the resistance greater than 10,000 ohms? REPEAT the self-test. CHECK FOR CORRECT SJB OPERATION Disconnect all the SJB connectors. Check for: INSTALL a new SJB. REFER to Section corrosion TEST the system for normal pushed-out pins operation. Connect all the SJB connectors and make sure they seat correctly. The system is operating correctly at this Operate the system and verify the concern is still present. time. The concern may have been caused Is the concern still present? by a loose or corroded connector. CLEAR any DTCs. REPEAT the self-test. Pinpoint Test N: One Turn Signal/Hazard Lamp Is Inoperative/Always On rmal Operation Fusion When the smart junction box (SJB) detects the multifunction switch in the LH TURN position, the SJB sends voltage through circuit CLS21 (BU/GN) to the LH front turn lamp. When the SJB detects the multifunction switch in the RH TURN position, the SJB sends voltage through circuit CLS25 (YE/VT) to the RH front turn lamp. Circuit GD123 (BK/GY) and circuit GD121 (BK/YE) provide ground for the LH and RH front turn lamps, respectively. The rear turn lamps are controlled utilizing the rear stoplamp circuits. rmal Operation Milan When the SJB detects the multifunction switch in the LH TURN position, the SJB sends voltage through circuit CLS21 (BU/GN) to the LH front turn lamp, and through circuit CLS18 (GY/BN) to the LH rear turn lamp. When the SJB detects the multifunction switch in the RH TURN position, the SJB sends voltage through circuit CLS25 (YE/VT) to the RH front turn lamp, and through circuit CLS19 (VT/OG) to the RH rear turn lamp. Circuit GD123 (BK/GY) and circuit GD121 (BK/YE) provide ground for the LH and RH front turn lamps, respectively. Circuit GD171 (BK/GY) provides ground for the rear turn lamps.

5 Exterior Lighting rmal Operation Zephyr When the SJB detects the multifunction switch in the LH TURN position, the SJB sends voltage through circuit CLS21 (BU/GN) to the LH front turn lamp, and through circuit CLS18 (GY/BN) to the LH rear turn lamp. When the SJB detects the multifunction switch in the RH TURN position, the SJB sends voltage through circuit CLS25 (YE/VT) to the RH front turn lamp, and through circuit CLS19 (VT/OG) to the RH rear turn lamp. Circuit GD123 (BK/GY) and circuit GD121 (BK/YE) provide ground for the LH and RH front turn lamps, respectively. Circuit GD171 (BK/GY) provides ground for the rear turn lamps. On vehicles equipped with daytime running lamps (DRL), the front turn lamps are utilized as the DRL. Possible Causes Circuit CLS18 (GY/BN) open, short to ground or voltage Circuit CLS19 (VT/OG) open, short to ground or voltage Circuit CLS21 (BU/GN) open, short to ground or voltage Circuit CLS25 (YE/VT) open, short to ground or voltage Circuit GD121 (BK/YE) open Circuit GD123 (BK/GY) open Circuit GD171 (BK/GY) open N1 N2 PINPOINT TEST N: ONE TURN SIGNAL/HAZARD LAMP IS INOPERATIVE/ALWAYS ON DETERMINE IF A TURN LAMP IS ALWAYS ON Ignition ON. Monitor the turn lamps while placing the multifunction switch in GO to N4. the RH TURN, LH TURN and NEUTRAL positions. Is any turn lamp always on? GO to N2. CHECK THE TURN LAMP GROUND CIRCUITRY FOR AN OPEN Disconnect: Inoperative Turn Lamp. Measure the resistance between the inoperative turn lamp, harness side and ground as follows: Inoperative Turn Lamp Connector-Pin Circuit LH front C GD123 (BK/GY) RH front C GD121 (BK/YE) LH rear (Milan, C413-1 GD171 (BK/GY) Zephyr) RH rear (Milan, C416-1 GD171 (BK/GY) GO to N3. Zephyr) REPAIR the circuit in question. CLEAR the Is the resistance less than 5 ohms? DTCs. REPEAT the self-test N3 CHECK THE TURN LAMP VOLTAGE SUPPLY CIRCUITRY FOR AN OPEN AND A SHORT TO GROUND Disconnect: SJB C2280e (Rear Lamp) or C2280a (Front Lamp). Measure the resistance between the inoperative turn lamp, harness side and the SJB, harness side; and between the inoperative turn lamp, harness side and ground as follows: (Continued)

6 Exterior Lighting N3 PINPOINT TEST N: ONE TURN SIGNAL/HAZARD LAMP IS INOPERATIVE/ALWAYS ON (Continued) CHECK THE TURN LAMP VOLTAGE SUPPLY CIRCUITRY FOR AN OPEN AND A SHORT TO GROUND (Continued) Inoperative Turn Lamp Connector-Pin SJB Connector-Pin Circuit LH front C C2280a-21 CLS21 (BU/GN) RH front C C2280a-9 CLS25 (YE/VT) LH rear (Milan, C2280e-11 CLS18 (GY/BN) Zephyr) C413-3 RH rear (Milan, C2280e-7 CLS19 (VT/OG) Zephyr) C416-3 GO to N5. Is the resistance less than 5 ohms between the inoperative turn lamp and the SJB, and greater than 10,000 ohms REPAIR the circuit in question. CLEAR the between the inoperative turn lamp and ground? DTCs. REPEAT the self-test N4 CHECK THE TURN LAMP VOLTAGE SUPPLY CIRCUITRY FOR A SHORT TO VOLTAGE Disconnect: SJB C2280e (Rear Lamp) or C2280a (Front Lamp). For the LH front turn lamp, REPAIR circuit Ignition ON. CLS21 (BU/GN). CLEAR the DTCs. Does the turn lamp in question continue to illuminate? REPEAT the self-test. For the RH front turn lamp, REPAIR circuit CLS25 (YE/VT). CLEAR the DTCs. REPEAT the self-test. For the LH rear turn lamp, REPAIR circuit CLS18 (GY/BN). CLEAR the DTCs. REPEAT the self-test. For the RH rear turn lamp, REPAIR circuit CLS19 (VT/OG). CLEAR the DTCs. REPEAT the self-test. GO to N5. N5 CHECK FOR CORRECT SJB OPERATION Disconnect all the SJB connectors. INSTALL a new SJB. REFER to Section Check for: TEST the system for normal corrosion operation. pushed-out pins Connect all the SJB connectors and make sure they seat The system is operating correctly at this correctly. time. The concern may have been caused Operate the system and verify the concern is still present. by a loose or corroded connector. CLEAR Is the concern still present? the DTCs. REPEAT the self-test. Pinpoint Test O: The Hazard Lamps Are Inoperative rmal Operation The smart junction box (SJB) sends a voltage reference signal to the hazard lamp switch through circuit CLS32 (BN/YE). When the hazard switch is engaged, the voltage signal is routed to ground through circuit GD116 (BK/VT). When the SJB detects a request for the hazard lamps, the SJB sends voltage to the appropriate turn lamps. Possible Causes Circuit CLS32 (BN/YE) open or short to ground Circuit GD116 (BK/VT) open Hazard lamp switch

7 Exterior Lighting O1 PINPOINT TEST O: THE HAZARD LAMPS ARE INOPERATIVE CHECK CIRCUIT GD116 (BK/VT) FOR AN OPEN Disconnect: Hazard Lamp Switch C2355. Measure the resistance between the hazard lamp switch C2355-1, circuit GD116 (BK/VT), harness side and ground. O2 GO to O2. Is the resistance less than 5 ohms? normal operation. CHECK CIRCUIT CLS32 (BN/YE) FOR A SHORT TO GROUND Disconnect: SJB C2280d. Measure the resistance between the SJB C2280d-20, circuit CLS32 (BN/YE), harness side and ground. O3 GO to O3. Is the resistance greater than 10,000 ohms? normal operation CHECK CIRCUIT CLS32 (BN/YE) FOR AN OPEN Measure the resistance between the hazard lamp switch C2355-5, circuit CLS32 (BN/YE), harness side and the SJB C2280d-20, circuit CLS32 (BN/YE), harness side. GO to O4. Is the resistance less than 5 ohms? normal operation. (Continued)

8 Exterior Lighting O4 PINPOINT TEST O: THE HAZARD LAMPS ARE INOPERATIVE (Continued) CHECK THE HAZARD LAMP SWITCH Connect: Hazard Lamp Switch C2355. While pressing an releasing the hazard lamp switch, measure the resistance between the SJB C2280d-20, circuit CLS32 (BN/YE), harness side and ground. O5 GO to O5. INSTALL a new hazard lamp switch. REFER to Hazard Flasher Lamp Switch in Is the resistance less than 5 ohms with the switch pressed this section. TEST the system for normal and greater than 10,000 ohms with the switch released? operation. CHECK FOR CORRECT SJB OPERATION Disconnect all the SJB connectors. Check for: INSTALL a new SJB. REFER to Section corrosion TEST the system for normal pushed-out pins operation. Connect all the SJB connectors and make sure they seat correctly. The system is operating correctly at this Operate the system and verify the concern is still present. time. The concern may have been caused Is the concern still present? by a loose or corroded connector. Pinpoint Test P: The Hazard Lamps Are Always On rmal Operation The smart junction box (SJB) sends a voltage reference signal to the hazard lamp switch through circuit CLS32 (BN/YE). When the hazard switch is engaged, the voltage signal is routed to ground through circuit GD116 (BK/VT). When the SJB detects a request for the hazard lamps, the SJB sends voltage to the appropriate turn lamps. Possible Causes Circuit CLS32 (BN/YE) open or short to ground Circuit GD116 (BK/VT) open Hazard lamp switch P1 PINPOINT TEST P: THE HAZARD LAMPS ARE ALWAYS ON CHECK CIRCUIT GD116 (BK/VT) FOR AN OPEN Disconnect: Hazard Lamp Switch C2355. (Continued)

9 Exterior Lighting P1 PINPOINT TEST P: THE HAZARD LAMPS ARE ALWAYS ON (Continued) CHECK CIRCUIT GD116 (BK/VT) FOR AN OPEN (Continued) Measure the resistance between the hazard lamp switch C2355-1, circuit GD116 (BK/VT), harness side and ground. P2 GO to P2. Is the resistance less than 5 ohms? normal operation. CHECK CIRCUIT CLS32 (BN/YE) FOR A SHORT TO GROUND Disconnect: SJB C2280d. Measure the resistance between the SJB C2280d-20, circuit CLS32 (BN/YE), harness side and ground. P3 GO to P3. Is the resistance greater than 10,000 ohms? normal operation CHECK CIRCUIT CLS32 (BN/YE) FOR AN OPEN Measure the resistance between the hazard lamp switch C2355-5, circuit CLS32 (BN/YE), harness side and the SJB C2280d-20, circuit CLS32 (BN/YE), harness side. P4 GO to P4. Is the resistance less than 5 ohms? normal operation. CHECK THE HAZARD LAMP SWITCH Connect: Hazard Lamp Switch C2355. (Continued)

10 Exterior Lighting P4 PINPOINT TEST P: THE HAZARD LAMPS ARE ALWAYS ON (Continued) CHECK THE HAZARD LAMP SWITCH (Continued) While pressing an releasing the hazard lamp switch, measure the resistance between the SJB C2280d-20, circuit CLS32 (BN/YE), harness side and ground. P5 GO to P5. INSTALL a new hazard lamp switch. REFER to Hazard Flasher Lamp Switch in Is the resistance less than 5 ohms with the switch pressed this section. TEST the system for normal and greater than 10,000 ohms with the switch released? operation. CHECK FOR CORRECT SJB OPERATION Disconnect all the SJB connectors. Check for: INSTALL a new SJB. REFER to Section corrosion TEST the system for normal pushed-out pins operation. Connect all the SJB connectors and make sure they seat correctly. The system is operating correctly at this Operate the system and verify the concern is still present. time. The concern may have been caused Is the concern still present? by a loose or corroded connector.

2005 Mustang Workshop Manual

2005 Mustang Workshop Manual Page 1 of 6 SECTION 417-01: Exterior Lighting 2005 Mustang Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 07/23/2009 Stoplamps Printable View (190 KB) Refer to Wiring Diagrams Cell 90 for

More information

NOTE: The Smart Junction Box (SJB) is also known as the Generic Electronic Module (GEM).

NOTE: The Smart Junction Box (SJB) is also known as the Generic Electronic Module (GEM). SECTION 417-01: Exterior Lighting 2009 Mustang Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 05/23/2008 Reversing Lamps Special Tool(s) 73III Automotive Meter 105-R0057 or equivalent Vehicle

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 413-09-1 Warning Devices 413-09-1 DIAGNOSIS AND TESTING Gauges And Warning Devices Refer to Wiring Diagrams Cell 59 for schematic and connector information. Refer to Wiring Diagrams Cell 60 for schematic

More information

SECTION Exterior Lighting

SECTION Exterior Lighting 417-01-i Exterior Lighting 417-01-i SECTION 417-01 Exterior Lighting CONTENTS PAGE DIAGNOSIS AND TESTING Headlamps... 417-01-2 Principles of Operation... 417-01-2 Inspection and Verification... 417-01-3

More information

Front Electronic Module (FEM)

Front Electronic Module (FEM) Page 1 of 6 Your Current Vehicle: 2005 Ford Thunderbird Front Electronic Module (FEM) SECTION 419-10: Multifunction Electronic Modules 2005 Thunderbird Workshop Manual DIAGNOSIS AND TESTING Procedure revision

More information

SECTION Handles, Locks, Latches and Entry Systems

SECTION Handles, Locks, Latches and Entry Systems 501-14-i Handles, Locks, Latches and Entry Systems 501-14-i SECTION 501-14 Handles, Locks, Latches and Entry Systems CONTENTS PAGE DIAGNOSIS AND TESTING Handles, Locks, Latches and Entry Systems... 501-14-2

More information

2004 Ranger Workshop Manual

2004 Ranger Workshop Manual Page 1 of 6 SECTION 413-00: Instrument Cluster and Panel Illumination 2004 Ranger Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 10/30/2003 Instrument Cluster and Panel Illumination Printable

More information

2008 F-Super Duty Workshop Manual

2008 F-Super Duty Workshop Manual Page 1 of 22 SECTION 501-14: Handles, Locks, Latches and Entry Systems 2008 F-Super Duty 250-550 Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 10/14/2009 Locks, Latches and Entry Systems

More information

SECTION Instrument Cluster and Panel Illumination

SECTION Instrument Cluster and Panel Illumination 413-00-i Instrument Cluster and Panel Illumination 413-00-i SECTION 413-00 Instrument Cluster and Panel Illumination CONTENTS PAGE DIAGNOSIS AND TESTING Instrument Cluster and Panel Illumination... 413-00-2

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 413-06-1 Horn 413-06-1 DIAGNOSIS AND TESTING Horn Special Tool(s) Fluke 77-IV Digital Multimeter FLU77-4 or equivalent Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) software

More information

Reversing Lamps. Special Tool(s) Fluke 77 IV Digital Multimeter FLU77 4 or equivalent

Reversing Lamps. Special Tool(s) Fluke 77 IV Digital Multimeter FLU77 4 or equivalent PINPOINT TEST V: BOTH REVERSI... PINPOINT TEST V: BOTH REVERSING LAMPS ARE INOPERATIVE (EXTERIOR LIGHTING) 417 01 Exterior Lighting 2010 F 150 DIAGNOSIS AND TESTING Procedure revision date: 07/28/2009

More information

2003 Crown Victoria/Grand Marquis/Marauder Workshop Manual

2003 Crown Victoria/Grand Marquis/Marauder Workshop Manual Page 1 of 9 SECTION 413-00: Instrument Cluster and Panel Illumination 2003 Crown Victoria/Grand Marquis/Marauder Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 02/25/2004 Instrument Cluster

More information

SECTION Rear View Mirrors

SECTION Rear View Mirrors 501-09-i Rear View Mirrors 501-09-i SECTION 501-09 Rear View Mirrors CONTENTS PAGE DIAGNOSIS AND TESTING Rear View Mirrors Interior... 501-09-2 Principles of Operation... 501-09-2 Inspection and Verification...

More information

2002 F-Super Duty /Excursion Workshop Manual

2002 F-Super Duty /Excursion Workshop Manual Page 1 of 9 SECTION 417-01: Exterior Lighting 2002 F-Super Duty 250-550/Excursion Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 05/23/2001 Turn Signal and Hazard Lamps Refer to Wiring

More information

Page 1 of 5 Pinpoint Tests Pinpoint Test V: Both Reversing Lamps Are Inoperative Refer to Wiring Diagrams Cell 93, Reversing Lamps for schematic and connector information. rmal Operation 4R70E/4R75E Transmission

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 308-07A-1 DIAGNOSIS AND TESTING Electronic Shift Visual Inspection Chart Mechanical Electrical 308-07A-1 Refer to Wiring Diagrams Cell 34 for schematic and Halfshafts Junction box (JB) mini connector information.

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 413-00-1 Instrument Cluster and Panel Illumination 413-00-1 DIAGNOSIS AND TESTING Inspection and Verification Instrument Panel Illumination NOTE: The instrument cluster must be reconfigured Refer to Wiring

More information

SECTION Interior Lighting

SECTION Interior Lighting 417-02-i Interior Lighting 417-02-i SECTION 417-02 Interior Lighting CONTENTS PAGE DIAGNOSIS AND TESTING Interior Lighting... 417-02-2 Principles of Operation... 417-02-2 Inspection and Verification...

More information

SECTION Multifunction Electronic Modules

SECTION Multifunction Electronic Modules 419-10-i Multifunction Electronic Modules 419-10-i SECTION 419-10 Multifunction Electronic Modules CONTENTS PAGE DIAGNOSIS AND TESTING Smart Junction Box (SJB)... 419-10-2 Principles of Operation... 419-10-2

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 501-14-1 Handles, Locks, Latches and Entry Systems 501-14-1 DIAGNOSIS AND TESTING Locks, Latches and Entry Systems Refer to Wiring Diagrams Cell 117 for schematic and connector information. Special Tool(s)

More information

2006 Low Cab Forward Workshop Manual. REMOVAL AND INSTALLATION Procedure revision date: 03/29/2005

2006 Low Cab Forward Workshop Manual. REMOVAL AND INSTALLATION Procedure revision date: 03/29/2005 SECTION 211-04: Steering Column REMOVAL AND INSTALLATION Procedure revision date: 03/29/2005 Steering Column Material Item Multi-Purpose Grease XG-4 and/or XL-5 Removal Specification ESB-M1C93-B 1. Remove

More information

SECTION Rear View Mirrors

SECTION Rear View Mirrors 501-09-i Rear View Mirrors 501-09-i SECTION 501-09 Rear View Mirrors CONTENTS PAGE DIAGNOSIS AND TESTING Rear View Mirrors Exterior... 501-09-2 Principles of Operation... 501-09-2 Inspection and Verification...

More information

ALTERNATOR REQUESTED INFORMATION. Vehicles With Dual Generator [ Engine Mount - LH ] 2007 Ford Pickup 6.0L Eng F350 Super Duty

ALTERNATOR REQUESTED INFORMATION. Vehicles With Dual Generator [ Engine Mount - LH ] 2007 Ford Pickup 6.0L Eng F350 Super Duty ALTERNATOR 2007 Ford Pickup 6.0L Eng F350 Super Duty REQUESTED INFORMATION Vehicles With Dual Generator [ Engine Mount - LH ] Fig 1: Rotating Drive Belt Tensioner Clockwise 1. Remove the accessory drive

More information

2003 Explorer/Mountaineer Workshop Manual

2003 Explorer/Mountaineer Workshop Manual Page 1 of 11 SECTION 414-00: Battery and Charging System 2003 Explorer/Mountaineer Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 06/18/2002 Charging System Printable View (257 KB) Refer

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 414-00-1 Charging System General Information 414-00-1 DIAGNOSIS AND TESTING Charging System The charging system voltage is controlled by the PCM. The generator charges the battery, and at the Special Tool(s)

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 307-05-1 Automatic Transaxle/Transmission External Controls 307-05-1 DIAGNOSIS AND TESTING Visual Inspection Chart External Controls Mechanical Electrical Refer to Wiring Diagrams Cell 37 for schematic

More information

Page 1 of 6 Pinpoint Test R: The Heated Seat is Inoperative Driver Refer to Wiring Diagrams Cell 119, Climate Controlled Seats for schematic and connector information. rmal Operation The heated seat module

More information

2002 Cougar Workshop Manual

2002 Cougar Workshop Manual SECTION 413-01: Instrument Cluster 2002 Cougar Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 12/10/2001 Instrument Cluster Refer to Wiring Diagrams Cell 60 for schematic and connector

More information

2002 F-150 Workshop Manual

2002 F-150 Workshop Manual Page 1 of 23 SECTION 310-03: Speed Control 2002 F-150 Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 08/07/2006 Speed Control Refer to Wiring Diagrams Cell 31, Speed Control for schematic

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 204-04-1 Wheels and Tires 204-04-1 DIAGNOSIS AND TESTING Tire Pressure Monitoring System Special Tool(s) Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) software with appropriate

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 415-00-1 Information and Entertainment Systems 415-00-1 DIAGNOSIS AND TESTING Information and Entertainment System Visual Inspection Chart Mechanical Electrical Refer to Wiring Diagrams Cell 130 for schematic

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 204-04-1 Wheels and Tires 204-04-1 DIAGNOSIS AND TESTING Tire Pressure Monitoring System Special Tool(s) Principles of Operation Activation Tool, Tire Pressure Monitor 204-363 Digital Tire Gauge 204-354

More information

2003 F-Super Duty /Excursion Workshop Manual

2003 F-Super Duty /Excursion Workshop Manual 3//2011 SECTION 310-03: Speed Control 2003 F-Super Duty 250-550/Excursion Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 08/01/2006 Speed Control Printable View (331 KB) Refer to Wiring

More information

SECTION Climate Control System - General Information

SECTION Climate Control System - General Information 412-00-i Climate Control System - General Information 412-00-i SECTION 412-00 Climate Control System - General Information CONTENTS PAGE DIAGNOSIS AND TESTING Climate Control System... 412-00-2 Inspection

More information

Page 1 of 54 412-00 Climate Control System General Information and Diagnostics 2006 Crown Victoria/Grand Marquis DIAGNOSIS AND TESTING Procedure revision date: 12/23/2008 Climate Control System Printable

More information

2001 Focus Workshop Manual

2001 Focus Workshop Manual Page 1 of 24 SECTION 413-01: Instrument Cluster 2001 Focus Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 04/23/2002 Instrument Cluster Refer to Wiring Diagrams Section 413-01 for schematic

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 501-10-1 Seating 501-10-1 DIAGNOSIS AND TESTING Seats Refer to Wiring Diagrams Cell 119 for schematic and connector information. Refer to Wiring Diagrams Cell 120, Power Seats for schematic and connector

More information

PINPOINT TEST B: INCORRECT FUEL GAUGE INDICATION

PINPOINT TEST B: INCORRECT FUEL GAUGE INDICATION 2012 Ford Truck Flex AWD V6-3.5L Vehicle > Instrument Panel, Gauges and Warning Indicators > Testing and Inspection > Pinpoint Tests > Instrumentation, Message Center and Warning Chimes PINPOINT TEST B:

More information

PINPOINT TEST A: THE CRUISE CONTROL IS INOPERATIVE

PINPOINT TEST A: THE CRUISE CONTROL IS INOPERATIVE 2010 Ford Truck F 150 2WD V8-5.4L Flex Fuel Vehicle > Cruise Control > Testing and Inspection > Pinpoint Tests PINPOINT TEST A: THE CRUISE CONTROL IS INOPERATIVE Cruise Control Pinpoint Tests Pinpoint

More information

SECTION Anti-Lock Brake System (ABS) and Stability Control

SECTION Anti-Lock Brake System (ABS) and Stability Control 206-09-i Anti-Lock Brake System (ABS) and Stability Control 206-09-i SECTION 206-09 Anti-Lock Brake System (ABS) and Stability Control CONTENTS PAGE DIAGNOSIS AND TESTING Anti-Lock Control... 206-09-2

More information

Instrumentation, Message Center and Warning Chimes

Instrumentation, Message Center and Warning Chimes SECTION 413-01: Instrumentation, Message Center, and Warning Chimes 2009 Mustang Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 07/15/2009 Instrumentation, Message Center and Warning Chimes

More information

Instrument Cluster (IC)

Instrument Cluster (IC) PINPOINT TEST F : THE TACHOME... PINPOINT TEST F : THE TACHOMETER IS INOPERATIVE (INSTRUMENT CLUSTER) 413 01 Instrument Cluster 2004 Ranger DIAGNOSIS AND TESTING Procedure revision date: 09/23/2008 Instrument

More information

2003 Town Car Workshop Manual

2003 Town Car Workshop Manual SECTION 415-00: Entertainment System General Information 2003 Town Car Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 06/24/2005 Audio System Printable View (298 KB) Refer to Wiring Diagrams

More information

1999 Expedition/Navigator Workshop Manual

1999 Expedition/Navigator Workshop Manual Page 1 of 16 SECTION 419-01: Anti-Theft PATS 1999 Expedition/Navigator Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 07/01/1998 Anti-Theft Passive Anti-Theft System (PATS) Refer to Wiring

More information

2006 Expedition/Navigator Workshop Manual

2006 Expedition/Navigator Workshop Manual Page 1 of 19 SECTION 204-05: Vehicle Dynamic Suspension DIAGNOSIS AND TESTING Procedure revision date: 10/06/2009 Vehicle Dynamic Suspension 4-Wheel Air Suspension Printable View (214 KB) Refer to Wiring

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 412-00-1 Climate Control System - General Information 412-00-1 DIAGNOSIS AND TESTING Climate Control System Refer to Wiring Diagrams Cell 54, Air Conditioner/Heater for schematic and connector information.

More information

Page 1 of 6 Pinpoint Test P: DTCs B1414:11, B1414:93, B1419:11 and B1419:93 Diagnostic Overview Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.

More information

2000 Town Car Workshop Manual

2000 Town Car Workshop Manual Page 1 of 30 SECTION 204-05: Vehicle Dynamic Suspension DIAGNOSIS AND TESTING Procedure revision date: 05/27/1999 Vehicle Dynamic Suspension Refer to Wiring Diagrams Cell 41, Rear Air Suspension for schematic

More information

SECTION A Four Wheel Drive (4WD) Systems

SECTION A Four Wheel Drive (4WD) Systems 308-07A-i Four Wheel Drive (4WD) Systems 308-07A-i SECTION 308-07A Four Wheel Drive (4WD) Systems CONTENTS PAGE DIAGNOSIS AND TESTING Four Wheel Drive (4WD) Systems Electronic Shift... 308-07A-2 Principles

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 501-11-1 Glass, Frames and Mechanisms 501-11-1 DIAGNOSIS AND TESTING Glass, Frames and Mechanisms Refer to Wiring Diagrams Cell 56 for schematic and connector information. Refer to Wiring Diagrams Cell

More information

2001 Cougar Workshop Manual

2001 Cougar Workshop Manual Page 1 of 7 SECTION 303-06: Starting System 2001 Cougar Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 09/14/2001 Starting System Refer to Wiring Diagrams Section 303-06 for schematic and

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 206-09-1 Vehicle Dynamic Systems 206-09-1 DIAGNOSIS AND TESTING Anti-Lock Control Traction Control and Stability Assist Special Tool(s) Principles of Operation 73III Automotive Meter 105-R0057 or equivalent

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 412-00-1 Climate Control System - General Information 412-00-1 DIAGNOSIS AND TESTING Climate Control System Refer to Wiring Diagrams Cell 54, Air Conditioning/Heater for schematic and connector information.

More information

Page 1 of 8 SECTION 310-03: Speed Control 2001 Focus Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 04/22/2003 Speed Control Refer to Wiring Diagrams Section 310-03 for schematic and connector

More information

2004 Explorer/Mountaineer Workshop Manual

2004 Explorer/Mountaineer Workshop Manual Page 1 of 30 SECTION 413-00: Information, Gauges and Warning Devices 2004 Explorer/Mountaineer Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 02/18/2008 (IC) Printable View (606 KB) Refer

More information

1998 F-150/250 Workshop Manual

1998 F-150/250 Workshop Manual Page 1 of 74 SECTION 308-07A: Transfer Case General Information DIAGNOSIS AND TESTING Procedure revision date: 12/04/2002 Transfer Case ESOF Refer to Wiring Diagrams Cell 34, Electric Shift Control for

More information

2001 F-Super Duty /Excursion/F-53 Motorhome Chassis Workshop Manual

2001 F-Super Duty /Excursion/F-53 Motorhome Chassis Workshop Manual 2001 F-Super Duty 250-550/Excursion/F-53 Motorhome Cha... Page 1 of 48 SECTION 308-07A: Four Wheel Drive (4WD) Systems 2001 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis Workshop Manual DIAGNOSIS

More information

Cooling Fan (CF) Module Connector

Cooling Fan (CF) Module Connector Page 1 of 14 Year = 2006 Model = Town Car Engine = VIN = IDS Version = 92.01 (IDS-92.01) Variable Speed Electric Cooling Fan WARNING: Crown Victoria Police Interceptor vehicles equipped with fire suppression

More information

Refer to Wiring Diagrams Cell 46, Supplemental Restraint System for schematic and connector information.

Refer to Wiring Diagrams Cell 46, Supplemental Restraint System for schematic and connector information. Page 1 of 12 Pinpoint Test AG: DTCs B0061:11, B0061:12, B0061:13 and B0061:1C Diagnostic Overview Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.

More information

2007 F-Super Duty Workshop Manual

2007 F-Super Duty Workshop Manual Page 1 of 30 SECTION 308-07A: Four Wheel Drive (4WD) Systems DIAGNOSIS AND TESTING Procedure revision date: 04/30/2009 Four Wheel Drive (4WD) Systems Electronic Shift Printable View (754 KB) Refer to Wiring

More information

2001 Explorer Sport/Sport Trac Workshop Manual

2001 Explorer Sport/Sport Trac Workshop Manual Page 1 of 11 SECTION 303-06: Starting System 2001 Explorer Sport/Sport Trac Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 03/18/2004 Starting System Refer to Wiring Diagrams Cell 20 for

More information

ME: Fuel Pump Control - High Pressure Fuel Injection Pump

ME: Fuel Pump Control - High Pressure Fuel Injection Pump Page 1 of 6 2008 Ford F-250 Super Duty : Diagnostics > 6.4L Diesel > Pinpoint Tests > ME: Fuel Pump Control - High Pressure Fuel Injection Pump ME: Fuel Pump Control - High Pressure Fuel Injection Pump

More information

Page 1 of 5 Pinpoint Test M: DTCs B1407:11, B1407:12, B1407:13 and B1407:1A Diagnostic Overview Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.

More information

Variable Geometry Turbocharger (VGT) Actuator Connector

Variable Geometry Turbocharger (VGT) Actuator Connector Page 1 of 5 Year = 2006 Model = F-Super Duty Engine = VIN = IDS Version = 77A.05 (IDS-77A.05) Variable Geometry Turbocharger (VGT) Output Circuit Function The VGT actuator is a variable position valve

More information

2006 Ford F-350 Super Duty - Diagnostics > Diagnostic Routines > Body > Instrumentation and W... Page 1 of 61

2006 Ford F-350 Super Duty - Diagnostics > Diagnostic Routines > Body > Instrumentation and W... Page 1 of 61 2006 Ford F-350 Super Duty - Diagnostics > Diagnostic Routines > Body > Instrumentation and W... Page 1 of 61 2006 Ford F-350 Super Duty : Diagnostics > Diagnostic Routines > Body > Instrumentation and

More information

Page 1 of 10 SECTION 501-11: Glass, Frames and Mechanisms 2000 Explorer/Mountaineer Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 06/17/1999 Glass, Frames and Mechanisms Refer to Wiring

More information

1998 Crown Victoria/Grand Marquis Workshop Manual

1998 Crown Victoria/Grand Marquis Workshop Manual Section 17-01: Lighting, Exterior Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 03/16/1998 Headlamps (With Autolamps) Inspection and Verification 1. Verify the customer's concern by operating

More information

DS: Air Conditioning Pressure (ACP) Transducer Sensor

DS: Air Conditioning Pressure (ACP) Transducer Sensor 2009 PCED Gasoline Engines SECTION 5: Pinpoint Tests Procedure revision date: 08/12/2009 DS: Air Conditioning Pressure () Transducer Sensor DS: Introduction DS1 CHECK FOR DIAGNOSTIC TROUBLE CODES (DTCS)

More information

PPT RH: REDUCTANT HEATER (6.7L DIESEL) 2011 PCED 6.7L Diesel SECTION 5: Pinpoint Tests Procedure revision date: 02/25/2014

PPT RH: REDUCTANT HEATER (6.7L DIESEL) 2011 PCED 6.7L Diesel SECTION 5: Pinpoint Tests Procedure revision date: 02/25/2014 PPT RH: REDUCTANT HEATER (6.7... PPT RH: REDUCTANT HEATER (6.7L DIESEL) 2011 PCED 6.7L Diesel SECTION 5: Pinpoint Tests Procedure revision date: 02/25/2014 RH: Reductant Heater RH: Introduction RH1 PRELIMINARY

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 307-01-1 Automatic Transaxle/Transmission 307-01-1 DIAGNOSIS AND TESTING Pinpoint Tests OSC Equipped Vehicle Special Tool(s) Transmission Fluid Pressure Gauge 307-004 (T57L-77820-A) Special Tool(s) MLP-TR

More information

2002 Taurus/Sable Workshop Manual

2002 Taurus/Sable Workshop Manual Page 1 of 69 SECTION 412-00: Climate Control System - General Information 2002 Taurus/Sable Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 02/05/2005 Climate Control System Refer to Wiring

More information

Pinpoint Tests OSC Equipped Vehicle

Pinpoint Tests OSC Equipped Vehicle SECTION 307-01: Automatic Transaxle/Transmission 5R55S 2009 Mustang Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 11/19/2008 Pinpoint Tests OSC Equipped Vehicle Special Tool(s) 73 III

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 308-07A-1 DIAGNOSIS AND TESTING Electronic Shift Refer to Wiring Diagrams Cell 34, Four-Wheel Drive Systems for schematic and connector information. Special Tool(s) 308-07A-1 Vacuum Test Tool, Knuckle

More information

Page 1 of 14 SECTION 204-05: Vehicle Dynamic Suspension 4-Wheel DIAGNOSIS AND TESTING Procedure revision date: 04/21/2006 Vehicle Dynamic Suspension 4-Wheel Air Suspension Printable View (207 KB) Refer

More information

2000 Crown Victoria/Grand Marquis Workshop Manual

2000 Crown Victoria/Grand Marquis Workshop Manual Page 1 of 15 SECTION 501-16: Wipers and Washers 2000 Crown Victoria/Grand Marquis Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 06/21/1999 Wipers and Washers Refer to Wiring Diagrams Cell

More information

Page 1 of 29 Section 04-05: Suspension, Computer Controlled 1997 Town Car Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 05/16/2000 Suspension, Computer Controlled Inspection and Verification

More information

1998 E-Series Workshop Manual

1998 E-Series Workshop Manual SECTION 206-09A: Anti-Lock Control Rear DIAGNOSIS AND TESTING Procedure revision date: 02/08/2000 Anti-Lock Control Refer to Wiring Diagrams Cell 42, Speed Control for schematic and connector information.

More information

Note: If DTCs P0670 and P0684 are present, carry out DTC P0670 diagnosis before diagnosing DTC P0684.

Note: If DTCs P0670 and P0684 are present, carry out DTC P0670 diagnosis before diagnosing DTC P0684. 2008 F-250 2008 PCED 6.4L Diesel SECTION 5: Pinpoint Tests Report a problem with this article Procedure revision date: 03/09/2010 AF: Glow Plug System AF: Introduction AF1 PRELIMINARY DIAGNOSIS te: If

More information

SECTION Wheels and Tires

SECTION Wheels and Tires 204-04-i Wheels and Tires 204-04-i SECTION 204-04 Wheels and Tires CONTENTS PAGE DIAGNOSIS AND TESTING Tire Pressure Monitoring System... 204-04-2 Principles of Operation... 204-04-2 Ambient Temperature

More information

DP: Vehicle Speed Sensor (VSS)/Transfer Case Speed Sensor (TCSS) DP: Introduction

DP: Vehicle Speed Sensor (VSS)/Transfer Case Speed Sensor (TCSS) DP: Introduction PPT DP: VEHICLE SPEED SENSOR... PPT DP: VEHICLE SPEED SENSOR ()/TRANSFER CASE SPEED SENSOR (TCSS) (GASOLINE ENGINES) 2005 PCED Gasoline Engines SECTION 5: Pinpoint Tests Procedure revision date: 03/30/2005

More information

1998 Expedition/Navigator Workshop Manual

1998 Expedition/Navigator Workshop Manual Page 1 of 64 SECTION 308-07A: Transfer Case General Information DIAGNOSIS AND TESTING Procedure revision date: 05/06/2002 Transfer Case Refer to Wiring Diagrams Cell 34 (Expedition, Navigator), All-Wheel

More information

2//2011 Section 206-05: Parking Brake and Actuation DIAGSIS AND TESTING Workshop Manual Parking Brake and Actuation Electrical Schematic Reference(s) Refer to Electrical and Vacuum Troubleshooting Manual,

More information

FA: AMBIENT AIR TEMPERATURE (AAT) SENSOR: PINPOINT TEST

FA: AMBIENT AIR TEMPERATURE (AAT) SENSOR: PINPOINT TEST 2014 Ford Taurus FWD V6-35L Vehicle > Powertrain Management > Computers and Control Systems > Testing and Inspection > Pinpoint Tests FA: AMBIENT AIR TEMPERATURE (AAT) SENSOR: PINPOINT TEST FA: Ambient

More information

DR: Camshaft Position (CMP) Sensor

DR: Camshaft Position (CMP) Sensor 2007 PCED On Board Diagnostics SECTION 5: Pinpoint Tests Procedure revision date: 03/29/2006 DR: Camshaft Position () Sensor DR: Introduction DR1 CHECK FOR DIAGNOSTIC TROUBLE CODES (DTCS) Are DTCs P0340,

More information

All vehicles. 1. Turn all vehicle accessories OFF. system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury in

All vehicles. 1. Turn all vehicle accessories OFF. system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury in 501-20B-1 GENERAL PROCEDURES (SRS) Deactivation and Reactivation Special Tool(s) Diagnostic Tool, Restraint System 418-F403 Diagnostic Tool, Restraint System (2 required) 418-133 501-20B-1 WARNING: Never

More information

Page 1 of 50 Section 412-00: Climate Control System General Information DIAGSIS AND TESTING 1997 Mark VIII Workshop Manual Climate Control System Special Service Tool(s) 73 Digital Multimeter 105-R0051

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 419-10-1 Multifunction Electronic Modules 419-10-1 DIAGNOSIS AND TESTING Diagnostic Trouble Code Chart Diagnostic Trouble Code (DTC) Chart B1084 Trunk Lamp Smart Junction Box (SJB) REFER to Section 417-02.

More information

2002 F-Super Duty /Excursion Workshop Manual

2002 F-Super Duty /Excursion Workshop Manual Page 1 of 56 SECTION 413-01: Instrument Cluster 2002 F-Super Duty 250-550/Excursion Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 11/18/2005 Instrument Cluster Refer to Wiring Diagrams

More information

Fuel Pump (FP ) Relay

Fuel Pump (FP ) Relay Page 1 of 12 Year = 2007 Model = F-150 Engine = VIN = IDS Version = t Available Fuel Pump (FP ) Relay This pinpoint test is intended to diagnose the following: fuel pump relay (9345) inertia fuel shutoff

More information

SERVICE DIAGNOSTIC INFORMATION. (Yes/No) Symptom(s) DTCs Stored In GEM (And/Or) Potential Cause Procedure

SERVICE DIAGNOSTIC INFORMATION. (Yes/No) Symptom(s) DTCs Stored In GEM (And/Or) Potential Cause Procedure LAMP 4X4 LAMP FLASHING AND 4X4 Article No. INOPERATIVE VEHICLES WITH A4WD 99-14-2 TRANSMISSION AND 4.0L TRANSMISSION A4WD 4X4 LAMP FLASHING AND 4X4 INOPERATIVE VEHICLES WITH 4.0L FORD: 1997-1999 EXPLORER

More information

DA: Intake Air Temperature (IAT) Sensor

DA: Intake Air Temperature (IAT) Sensor 2007 PCED On Board Diagnostics SECTION 5: Pinpoint Tests Procedure revision date: 03/29/2006 DA: Intake Air Temperature () Sensor DA: Introduction DA1 CHECK FOR DIAGNOSTIC TROUBLE CODES (DTCS) Are DTCs

More information

Fuel Injector Control Module (FICM ) Low Voltage

Fuel Injector Control Module (FICM ) Low Voltage Page 1 of 6 Year = 2006 Model = F-Super Duty Engine = VIN = Fuel Injector Control Module (FICM ) Low Voltage Circuit Function The FICM requires a 12-volt power source. The FICM receives power from the

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 2007 Ford F650 : Brakes > Air Brake System General Information > DIAGNOSIS AND TESTING DIAGNOSIS AND TESTING Listen SECTION 206 00B: Brake System General Information Air 2007 F Super Duty 650 750 Workshop

More information

Page 1 of 13 SECTION 413-01: Instrumentation, Message Center, and Warning Chimes 2005 Explorer/Mountaineer Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 07/17/2009 Instrumentation, Message

More information

Page 1 of 6 1Search Print Date: C200B Pinpoint Test B: DTCs C1B00, C200B, C200C, U2011, U2200 And U3000: Steering Angle Sensor, Steering Shaft Torque Sensor 1, Steering Shaft Torque Sensor 2, Motor And

More information

2002 Ford Explorer STARTING & CHARGING SYSTEMS' 'Generators & Regulators - Explorer & Mountaineer STARTING & CHARGING SYSTEMS

2002 Ford Explorer STARTING & CHARGING SYSTEMS' 'Generators & Regulators - Explorer & Mountaineer STARTING & CHARGING SYSTEMS DESCRIPTION 2002-03 STARTING & CHARGING SYSTEMS Generators & Regulators - Explorer & Mountaineer System consists of generator, regulator, battery, fuses, PCM and associated wiring. Generators have an electronic

More information

DRL RELAY CIRCUIT CIRCUIT DESCRIPTION

DRL RELAY CIRCUIT CIRCUIT DESCRIPTION 051562 DIAGNOSTICS 05ETR02 DRL RELAY CIRCUIT CIRCUIT DESCRIPTION The multiplex network body ECU controls DRL No.2, No. and No.4 relays. The headlamp (High) is connected in serial when the daytime running

More information

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING 211-00-1 Steering System 211-00-1 DIAGNOSIS AND TESTING Steering System Special Tool(s) Dial Thermometer 0-220 F 023-R0007 or equivalent Special Tool(s) Worldwide Diagnostic System (WDS) 418-F224, New

More information

2002 Explorer/Mountaineer Workshop Manual

2002 Explorer/Mountaineer Workshop Manual Page 1 of 20 SECTION 307-01: Automatic Transmission - 5R55W/S 2002 Explorer/Mountaineer Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 10/20/2004 Pinpoint Tests OSC Equipped Vehicles Special

More information

DIAGNOSIS AND TESTING Procedure revision date: 06/21/2000

DIAGNOSIS AND TESTING Procedure revision date: 06/21/2000 2001 F-350 Applies to: Gasoline Report a problem with this article Subarticles Inspection and Verification Symptom Chart Pinpoint Tests Component Tests SECTION 303-06A: Starting System Gasoline Engines

More information