Dial Test Indicators Comparison measuring instruments which ensure high quality, high accuracy and reliability.

Transcription

1 Dial Test s Comparison measuring instruments which ensure high quality, high accuracy and reliability. SERIES 513 ever-type Dial s eature icons Designed to probe surfaces that cannot be reached with a normal dial gauge. Useful both for alignment and for measurement purposes. Mitutoyo s proprietary new design permits smooth er operation. Strong frame provides excellent rigidity and durability. Non-magnetic er and contact permit reliable operation even in magnetic environments. Clear and concise wide dial face allows excellent visibility. The surface of the crystal is hard-coated for excellent scratch resistance. lat crystal makes graduations easy to read. Moreover, the O-ring sealing method used for the bezel prevents water or oil penetration. (Note that this type is NOT waterproof.) Six types are available: horizontal, horizontal (20 tilted face) vertical, parallel, universal, and pocket, allowing users to select the model most suited to their needs. Horizontal: Standard Horizontal (20 Tilted ace): Dial face inclined 20, compared with the vertical type, allows easy reading. Vertical: Best suited for centering holes under the spindle of a machine tool. Parallel: The scale can be read from the front, with the stylus pivoting in a plane parallel to that of the dial face. Universal: The direction of the probe movement can be freely changed. Pocket: Compact type Icon eature description With revolution counter ong stylus Jeweled bearing Double scale spacing type, easyon-the-eyes Compact Dustproof Anti-magnetic Yellow dial face for easy reading (Metric) Glare-free flat crystal face with hard coating One-piece bezel with O-ring seal Dovetail arge-pitch crown gear Dovetail, 3 positions (one-piece structure) Jeweled bearing Rubber cushion Special-alloy sector gear ø2mm -tipped stylus (Inclination range: 200 ) Ball-bearing pivot Dial test indicators with a ruby contact are available in the horizontal (standard) type. Benefits of ruby contact s: Several times more resistant to wear than. Can be used on electrical discharge machines without special precautions. ind Quality Products Online at: -61

2 DIMENSIONS ø40 unit: mm Dial Test SERIES 513 Horizontal Type Provides easy access to shrouded surfaces that cannot be reached with conventional dial indicators. No-clutch structure for automatic reversal of measuring direction. Resistant to water and dust thanks to the onepiece bezel and O-ring seal for the crystal. The glare-free flat crystal face has a scratchresistant coating. High sensitivity and quick response due to low-friction jeweled bearings E/ E E/ E E/ E E E/ E E E/ E E E E E ø E E E E E E E Ruby contact models Higher resistance to wear Non-magnetic, non-conductive tip allows use in EDM processes Special Set: No (mm) E: Dial test indicator 7014: Mini magnetic stand No (inch) : Dial test indicator 7014E: Mini magnetic stand Carbide contact models E E ind Quality Products Online at: E E E E -62

3 Dial Test s Comparison measuring instruments which ensure high quality, high accuracy and reliability. Set Configuration: Metric and Metric/Inch Anti-magnet Double scale spacing ong stylus Jeweled bearing ull set Compact With revolution counter (900321, for ø4mm, ø8mm, dovetail) Metric holding bar (: 100mm) Plus set ø1mm ø3mm ø4mm SPECIICATIONS Metric E E E E A T 0.01mm 0.5mm 5µm N or less E 0.01mm 0.5mm 5µm N or less E A T 0.01mm 0.5mm 10µm N or less E 0.01mm 0.5mm 5µm N or less E A T 0.01mm 0.8mm 8µm N or less E 0.01mm 0.8mm 8µm N or less E 0.01mm 0.8mm 8µm N or less E A T 0.01mm 1mm 10µm N or less E 0.01mm 1mm 10µm N or less E A 0.01mm 1.5mm 8µm N or less E A T 0.002mm 0.2mm 3µm N or less E 0.002mm 0.2mm 3µm N or less E 0.002mm 0.2mm 3µm N or less E A 0.002mm 0.6mm 6µm N or less E 0.001mm 0.14mm 3µm N or less E 0.001mm 0.14mm 3µm N or less 4 4 Provided with a ø2mm ruby contact as a substitute for ø2mm contact. Inch T ± N or less ± N or less T ± N or less ± N or less ± N or less T ± N or less ± N or less ± N or less Metric/inch T 0.002mm,.0001 Inch/Metric T.0005, 0.01mm ind Quality Products Online at: 0.2mm,.0075 Provided with a.079 DIA ruby contact as a substitute for.079 DIA contact µm Dial reading , Dial reading.03, 0.7mm ± , Measuring force 0.3N or less 4 4 Measuring force 0.3N or less 4 4 Set Configuration: Inch and Inch/Metric ull set.039 DIA. (900322, for.157" DIA., 3/8" DIA., dovetail) ø8mm.118 DIA. 3/8" DIA. ø2mm contact ().157" DIA. Inch holding bar (: 4").079 DIA. contact ()

4 Dial Test SERIES 513 Horizontal (20 Tilted ace), Vertical, and Parallel Types Specially designed for easy viewing of dial E The dial face obliquely faces upward, allowing users to read the graduations from the user's side. It is convenient when probing on the side of a large workpiece and the workbench is high. Using the universal holder allows easy hole centering. The dial face always faces upward when the indicator is rotated, which makes reading easy E E E E GE E E E Optional Accessories : s (See page -63.) : Holding bars (See page -63.) : Stems (See page -63.) : Styli (See page -63.) ind Quality Products Online at: GE

5 Dial Test s Comparison measuring instruments which ensure high quality, high accuracy and reliability. Anti-magnet SPECIICATIONS Metric Horizontal (20 tilted face) type With revolution counter Jeweled bearing ong stylus Dial reading Measuring force E A T 0.01mm 1.6mm 10µm N or less E A T 0.002mm 0.4mm 5µm N or less Inch Horizontal (20 tilted face) type Remarks T ± N or less T ± N or less Black dial T ± N or less T ± N or less Black dial T ± N or less T ± N or less Black dial Metric Vertical type E A T 0.01mm 0.8mm 8µm N or less E A T 0.002mm 0.2mm 3µm N or less 4 4 Inch Vertical type T ± N or less T ± N or less 4 4 Metric Parallel type GE GA GT 0.01mm 0.8mm 8µm N or less 4 Set Configuration: Metric ull set (900321, for ø4mm, ø8mm, dovetail) Plus set ø1mm.079 DIA. () Set Configuration: Inch ø3mm Metric holding bar (: 100mm) ø8mm ø4mm Inch Parallel type G GT ± N or less 4 DIMENSIONS ull set (900322, for.157" DIA., 3/8" DIA., dovetail) Inch holding bar (: 4") Horizontal (20 Tilted ace) Type unit: mm Plus set E E E E DIA..118 DIA..157" DIA. 7.5 ø Vertical Type Parallel Type ø ø40 ind Quality Products Online at: GE /8" DIA..079 DIA. ()

6 Set Configuration: Metric ull set ø1mm ø3mm ø4mm ( for ø4mm stem, ø8mm stem, dovetail) Metric holding bar (: 100mm) Spare stylus, ø2mm Dial Test SERIES 513 Universal Type Universal application to all directions. (Not only the direction of the measuring, but also the direction of measurement itself can be adjusted 360 degrees without moving the indicator.) ø2mm (102825) ø8mm stem Spanner (102037) Set Configuration: Inch ull set.039 DIA. ( for.157 DIA stem, 3/8" DIA. stem, dovetail) GE.118 DIA..157 DIA. Inch holding bar (: 4 ) Spare stylus,.079 DIA. SPECIICATIONS Metric Jeweled bearing ull set GE GT 0.01mm 0.8mm 8µm N or less 4 Inch ull set G GT ± N or less DIA. (102825) 3/8" DIA. stem DIMENSIONS Unit: mm Spanner (102037) ø40 Optional Accessories : s (See page -63.) : Holding bars (See page -63.) : Stems (See page -63.) : ø1mm ball contact () : ø2mm ball contact () : ø3mm ball contact () ind Quality Products Online at: GE

7 Dial Test s Comparison measuring instruments which ensure high quality, high accuracy and reliability. Pocket Type Dial Test SERIES 513 Jeweled bearings assure higher sensitivity and accuracy. can be mounted by clamping the stem or the body (except for WE and WT). Reversible measuring direction (Clutch type). Two holding bars are supplied. (ull sets only.) ully adjustable bezel/dial face. Stylus is adjustable within 220. Bezel is sealed with on O-ring to keep out water and oil E E WE E WE E T E T E E E E ind Quality Products Online at: -67 Optional Accessories : s (See page -64.) : Holding bars (See page -64.) : Stems (See page -64.) : Styli (See page -64.)

8 Set Configuration: Metric ull set ong stylus Jeweled bearing Dustproof Compact (900321, for ø4mm, ø8mm, dovetail) ø4mm ø2mm Metric holding bar (: 100mm) ø8mm holding rod (900211) ø8mm SPECIICATIONS Metric ull set E T 0.01mm 0.5mm 10µm N or less E T 0.01mm 0.8mm 8µm N or less WE WT 0.01mm 0.8mm 8µm N or less E T 0.01mm 0.8mm 8µm N or less T 0.01mm 1mm 10µm N or less E T 0.002mm 0.2mm 3µm N or less E T 0.001mm 0.14mm 3µm N or less 4 Inch ull set T ± N or less T ± N or less T ± N or less T ± N or less 4 DIMENSIONS Set Configuration: Inch ull set.039 DIA. Inch holding bar (: 4 ) Spanner (301336).118 DIA..157" DIA. (900322, for.157" DIA., 3/8" DIA., dovetail).315 DIA holding rod (900211) ø (33) 46 (29) ø33 (ø28) ( ): E 17 or WE, use the indicator with measuring range of ±30º ± E E T E E WE E ø unit: mm There are two types of Mitutoyo Dial Test : The non-clutch type (without a clutch lever) and the clutch type (with a two-position clutch lever) Non-clutch type Test Pointer Clutch type Test s.079 DIA. Contact Point Clutch lever Spanner (301336) 3/8" DIA. ind Quality Products Online at: In the non-clutch type, although the contact may move either in the upward or downward direction, the er always rotates clockwise. In the clutch type, if the clutch lever is set in one position the contact moves in the upward direction and the er rotates clockwise. Conversely, if the lever is set in the other position the contact moves in the downward direction and the er rotates counterclockwise. -68

9 Dial Test s Comparison measuring instruments which ensure high quality, high accuracy and reliability. Styli, Stems and Holders Optional Accessories for Dial Test s Styli (for Metric Models Only*) * Except for universal type dial test indicator ( G). Stylus length affects the scale factor of an indicator. The styli provided as standard give a scale factor of unity. Swivel Clamps Can be used with Holding Bars. or ø6mm stem, ø8mm stem, and dovetail or ø4mm stem, ø8mm stem, and dovetail or.157" DIA. stem, 3/8" DIA. stem, and dovetail ø0.5mm ball- ø0.7mm ball- Holding Bars (=14.7mm) (=20.9mm) (=22.3mm) (=44.5mm) ø1mm ball (=14.7mm) (=20.9mm) (=22.3mm) (=44.5mm) ø2mm ball- 9 x 9mm (ength: 50mm) (ength: 100mm) ø8mm (.315 DIA) (ength: 115mm/ ) 21CZA044 (=12.8mm) (=14.7mm) (=20.9mm) (=22.3mm) (=36.8mm) (=44.5mm) ø2mm ball- (Ruby) 21CZA036 (=12.8mm) (=14.7mm) (=20.9mm) (=22.3mm) (=36.8mm) (=44.5mm) ø3mm ball-.25 x.5" (ength: 2") (ength: 4") Universal Holder Allows the indicator to be set at the desired attitude to the workpiece. 21CZA212 (=12.8mm) 21CZA209 (=14.7mm) 21CZA201 (=20.9mm) 21CZA210 (=22.3mm) 21CZA211 (=44.5mm) Spanner 21CZA045 (=12.8mm) (=14.7mm) (=20.9mm) (=22.3mm) (=36.8mm) (=44.5mm) 21CZA233 (ø8mm stem) 21CZA231 (.25" DIA. stem) 21CZA229 (ø6mm stem) Universal holder Stems with Clamp Ring ø4mm (.157" DIA.) Centering Holder Allows large diameter cylinders or holes to be centered on a machine tool Centering holder ø8mm 3/8 DIA ind Quality Products Online at: (ø8mm stem) (.25" DIA. stem)

10 Styli, Stems and Holders Optional Accessories for Pocket Type Dial Test s Styli (for Metric Models Only) Stylus length affects the scale factor of an indicator. The styli provided as standard give a scale factor of unity. Swivel Clamps Can be used with Holding Bars. or ø6mm stem, ø8mm stem, and dovetail or ø4mm stem and ø8mm stem, and dovetail or.157" DIA. stem and 3/8" DIA. stem, and dovetail ø0.5mm ball- ø0.7mm ball- Holding Bars (=14.7mm) (=20.9mm) (=44.5mm) (=14.7mm) (=20.9mm) (=44.5mm) 9 x 9mm (ength: 50mm) (ength: 100mm) ø1mm ball- ø2mm ball- ø8mm (.315 DIA) (ength: 115mm) (=12.1mm) (=14.7mm) (=20.9mm) (=36.8mm) (=44.5mm) ø2mm ball- (Ruby) (=12.1mm) (=14.7mm) (=20.9mm) (=36.8mm) (=44.5mm) ø3mm ball-.25 x.5" (ength: 2") (ength: 4") Spanner 21CZA209 (=14.7mm) 21CZA201 (=20.9mm) 21CZA211 (=44.5mm) Stems (=12.1mm) (=14.7mm) (=20.9mm) (=36.8mm) (=44.5mm) ø4mm (.157" DIA.) ø8mm 3/8" DIA Universal Holder Allows the indicator to be set at the desired attitude to the workpiece. 21CZA234 (ø8mm stem) 21CZA232 (.25" DIA. stem) 21CZA230 (ø6mm stem) Universal holder ind Quality Products Online at: -70