Viking Installation Guide

Transcription

1 iking Installation Guide iking Range orporation Front Street Greenwood, Mississippi 890 US (66) For product information, call -888-IKING ( ) or visit the iking Web site at vikingrange.com U L U L Professional Hoods F0470G EN (0)

2 Table of ontents Warnings & Important Information -4 WH 0 H. Wall Hoods w/standard entilar 4, 0, & Dimensions & Specifications 5 learance Dimensions 6 Interior entilar Dimensions 7 WH 8 H. 4 /7 Deep Wall Hoods 4, 0,, 4, 48, 54, 60, & 6 Dimensions & Specifications 8 learance Dimensions 9 Interior entilar Dimensions 0 Exterior entilar Dimensions WH 8 H. T-Series Wall Hoods, 48, & 60 Dimensions & Specifications learance Dimensions WH himney Wall Hoods 0,, 4, 48, 54, 60, & 6 Dimensions & Specifications 4 learance Dimensions 5 Interior entilar Dimensions 6 Exterior entilar Dimensions 7 IH Island Hoods, 4, 54, & 6 Dimensions & Specifications 8 learance Dimensions 9 Interior entilar Dimensions 0 Exterior entilar Dimensions IH himney Island Hoods, 4, 54, & 6 Dimensions & Specifications learance Dimensions Interior entilar Dimensions 4 Exterior entilar Dimensions 5 Wall usm entilar System Dimensions & Specifications 6 Installing Hood anopy 7 learance Dimensions 8 entilar Dimensions 9 I Island usm entilar System Dimensions & Specifications Installing Hood anopy learance Dimensions I entilar Dimensions 4 Planning Information 6 Installation Procedures Installation (WH 0 H. Wall Hoods w/standard entilar) 7 Duct over Option (WH 0 H. Wall Hoods w/standard entilar) 9 Installation (WH 0 H. Wall Hoods w/recirculating Kit) 9 Installation (WH 8 H. Wall & WH himney Wall Hoods) 4 Duct over Option (WH 8 H. Wall Hoods) 4 Duct over Option (WH himney Wall Hoods) 44 Installation (IH/IH Island Hoods) 45 Service & Registration 47 IMPORTNT Please Read and Follow! NOTE: If installing hood with warming shelf panel, install warming shelf panel first. IMPORTNT PLESE RED ND FOLLOW efore beginning, please read these instructions completely and carefully. Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. Please observe all local and national codes and ordinances. If no local codes are applicable, wire in accordance with the National Electrical ode, NSI/NFP 70-latest edition. Damp environment approved models should be installed in a covered non-enclosed area and should be protected from the elements as much as possible. The installer should leave these instructions with the consumer who should retain for local inspecr s use and for future reference. heck with a qualified and trained installer or local codes for makeup air requirement, if any. This hood is for residential installation only and is not designed for installation over a commercial product. Make sure power is off at the main circuit breaker or fuse box before making connections. To avoid risk of fire, electric shock, or injury persons, turn off the electricity the hood from the power supply before servicing or cleaning. iking hoods are equipped with variable speed control blowers. These units will not function with a single speed ventilar. ll iking Range ventilar kits are designed specifically for use with iking Range hoods. Use of any non-iking Range ventilar kit will void the hood warranty. iking hoods are equipped with the variable speed controls for blowers. These units will not function with a single speed ventilar. ll iking ventilar kits are designed specifically for use with iking hoods. Use of any non-iking ventilar kit will void the hood warranty. RED ND SE THESE INSTRUTIONS W R N I N G To reduce the risk of fire, electric shock, or injury persons, observe the following: Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. efore servicing or cleaning unit, switch power off at service panel and lock service panel prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, the service panel. W R N I N G TO REDUE THE RISK OF FIRE, ELETRIL SHOK, OR INJURY TO PERSONS, OSERE THE FOLLOWING:. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.. Sufficient air is needed for proper combustion and exhausting of gases through the flute (chimney) of fuel burning equipment prevent back drafting. Follow the heating equipment manufacturer s guideline and safety standards such as those published by the National Fire Protection ssociation (NFP), and the merican Society for Heating, Refrigeration and ir onditioning Engineers (SHRE), and the local code authorities.. When cutting of drilling in wall or ceiling, do not damage electrical wiring and other hidden utilities. 4. Ducted fans must always be vented the outdoors. 5. WRNING!: To reduce risk of fire, use only metal ductwork 6. UTION!: To reduce risk of fire and properly exhaust air, be sure duct air outside. Do not vent exhaust air in spaces within walls or ceilings, or in attics, crawl spaces, or garages. 7. UTION!: To Reduce the Risk of Fire and Electric Shock, Install this rangehood only with remote blower models manufactured by iking, model numbers DE900/DE00, E900/E00, OR DE500, E500 or integral blowers manufactured by iking, model numbers DI00, DI440, DI600, DI800, DI00, I00, I600, or I00. NOTE Please refer inside for specific canopy/blower combinations.

3 IMPORTNT Please Read and Follow! W R N I N G To reduce the risk of injury persons in the event of a rangep grease fire, observe the following. (ased on Kitchen Firesafety Tips, published by NFP.). SMOTHER FLMES with a close fitted lid, cookie sheet, or metal tray, then turn off the burner. E REFUL TO PREENT URNS. If the flames do not go out immediately, EUTE ND LL THE FIRE DEPRTMENT.. NEER PIK UP FLMING PN. You may be burned.. DO NOT USE WTER, including wet dishcloths or wels a violent steam explosion will result. 4. Use an extinguisher ONLY if You know it is a lass extinguisher, and you already know how operate it. The fire is small and contained in the area where it started. The fire department is being called. You can fight the fire with your back an exit. U T I O N For general ventilating use only. Do not use exhaust hazardous or explosive materials and vapors. W R N I N G TO REDUE THE RISK OF FIRE, ELETRIL SHOK, OR INJURY TO PERSONS Rangehoods must be installed with the ventilars that are specified on their carn indicating suitability with this model. Other ventilars cannot be substituted. Dimensions & Specifications (WH 0 H. Wall Hoods w/standard entilar 4, 0, & ) (Hood width) 4 W. -7/8 (60.6 cm) 9-7/8 (76. cm) 5-7/8 (9. cm) (7.6 cm) NOTE: Optional duct cover sold separately. (5. cm) (0.5 cm) 0 (5.4 cm) WH 0 H. Wall Hoods w/standard entilar Description 4 0 Duct cover width -7/8 (60.6 cm) 9-7/8 (75.9 cm) 5-7/8 (9. cm) Duct cover depth Duct cover height (0.5 cm) (0.5 cm) Number of lights Number of filters Heat lamps Interior ventilar kit Interior duct size* N/ 460 FM Standard 7 (7.8 cm) Interior Maximum amps 5.6 * Disregard when using recirculating kits. 460 FM blower is shipped with hood. 4 5

4 learance Dimensions (WH 0 H. Wall Hoods w/standard entilar) Interior entilar Dimensions (WH 0 H. Wall Hoods w/standard entilar) (9.4 cm) 60 min. (5.4 cm) max. (60.0 cm) 4 min. (6.0 cm) 7 max.* (68.6 cm) 4 W. 4 W. 4 W. 4 W. -7/8 (60.6 cm) 9-7/8 (75.9 cm) 5-7/8 (9. cm) 5-/4 (. cm) 8-/4 (0.9 cm) -/4 (8.6 cm) -5/ (0. cm) 4-5/ (7.9 cm) 7-5/ (45.6 cm) D 5/8 (.6 cm) -5/8 (9. cm) 6-5/8 (6.8 cm) 4 (0. cm) 8 (4.6 cm) -4 (.9 cm) 7 (7.8 cm) dia. -7/8 (9.8 cm) D / (. cm) -/ (8.9 cm) Electrical hookup 460 FM Interior entilar Installation * NOTE: When installing with a 4 high-shelf, the 7 (68.6 cm) max. dimensions must be used. 6 7

5 Dimensions & Specifications (WH 8 H. 4 Deep Wall Hoods 4, 0,, 4, 48, 54, 60, & 6) (WH 8 H. 7 Deep Wall Hoods 0,, 4, 48, 54, 60, & 6) learance Dimensions (WH 8 H. Wall Hoods) (Hood width) 4 W. -7/8 (60.6 cm) 9-7/8 (76. cm) 5-7/8 (9. cm) 4 W. 4-7/8 (06.4 cm) 48 W. 47-7/8 (.6 cm) 5-7/8 (6.8 cm) 59-7/8 (5. cm) 65-7/8 (67. cm) (5. cm) (0.5 cm) 8 (45.7 cm) (Hood depth) 4 D. 4 (6.0 cm) 7 D. 7 (68.6 cm) NOTE: Optional duct cover sold separately. WH 8 H. Wall Hoods Description Duct cover width -7/8 (60.6 cm) 9-7/8 (75.9 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 47-7/8 (.6 cm) 5-7/8 (6.8 cm) 59-7/8 (5. cm) 65-7/8 (67. cm) 6min. (67.6 cm) 7 max. (8.9 cm) 0 min. (76. cm) max. (9.4 cm) Duct cover depth (0.5 cm) Duct cover height (0.5 cm) Number of lights 4 4 Number of filters 4 4 (9.4 cm) Heat lamps Interior ventilar kits Exterior ventilar kits IN00/ 600 DE900/ 00* IN00/ 600/00 DE900/ 00* IN00/ 600/00 DE900/ 00* IN600/ 00 DE900/ 00* IN00* IN00* IN00* IN00* DE00*/ 500** DE00*/ 500** DE00*/ 500** DE00*/ 500** In-line ventilar kits DIL900/00 DIL900/00 DIL900/00 DIL900/00 DIL00 DIL00 DIL00 DIL00 Interior duct size 7 (7.8 cm) 7 /0 (7.8/5.4 cm) 7 /0 (7.8/5.4 cm) 7 /0 (7.8/5.4 cm) 0 (5.4 cm) 0 (5.4 cm) 0 (5.4 cm) 0 (5.4 cm) Exterior duct size 0 (5.4 cm) Interior Maximum amps 4.9/ / / Exterior Maximum amps 8.7/ / / / /9. 8.5/9. 8.9/9. 8.9/9. In-Line Maximum amps 6.0/ / / / *,00 FM interior- or exterior-power ventilar should be used when installed over range/rangep with gas char-grill. Max duct run is 50 ft. ** It is recommended that the,500 FM ventilar be used with longer duct runs. Max duct run is 75 ft. NOTE: Maximum amp rating for hoods includes recommended ventilar kit rating; ll products must be hard wired with - wire with ground. n interior- or exterior-power ventilar kit must be purchased for installation with all 8 H. hoods. 8 9

6 Interior entilar Dimensions (WH 8 H. Wall Hoods) Exterior entilar Dimensions (WH 8 H. Wall Hoods) 4 W. 4 W. -5/ (0. cm) 4-5/ (7.9 cm) 7-5/ (45.6 cm) 0-5/ (5. cm) -5/ (60.8 cm) 6-5/ (68.4 cm) 9-5/ (76.0 cm) -5/ (8.7 cm) 4-5/8 (.7 cm) 8-/4 (47.6 cm) 7 (7.8 cm) dia. 9-/8 (.8 cm) 9-5/8 (4.4 cm) 0 5/8 (.6 cm) 9-/8 (. cm) 4 W. 4 W. -7/8 (60.6 cm) 9-7/8 (75.9 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 47-7/8 (.6 cm) 5-7/8 (6.8 cm) 59-7/8 (5. cm) 65-7/8 (67. cm) 4 W. 4 W. -5/ (0. cm) 4-5/ (7.9 cm) 7-5/ (45.6 cm) 0-5/ (5. cm) -5/ (60.8 cm) 6-5/ (68.4 cm) 9-5/ (76.0 cm) -5/ (8.7 cm) -/ 5-5/ (.7 cm) (5. cm) 9-/4 (4.8 cm) 0 (5.4 cm) dia. 8-/4 (0.9 cm) 6-7/ (6.4 cm) 0 -/ (6.5 cm) (7.6 cm) 4 W. 4 W. -7/8 (60.6 cm) 9-7/8 (75.9 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 47-7/8 (.6 cm) 5-7/8 (6.8 cm) 59-7/8 (5. cm) 65-7/8 (67. cm) 00 or 600 FM Interior entilar Installation for all Wall Hoods 900 or 00 FM Exterior entilar Installation for all Wall Hoods 8-/ (50.0 cm) 9-/8 (.8 cm) 5/8 (.6 cm) 5-5/ (5. cm) 8-/ (0.7 cm) 4 W. 4 W. -5/ (0. cm) 4-5/ (7.9 cm) 7-5/ (45.6 cm) 0-5/ (5. cm) -5/ (60.8 cm) 6-5/ (68.4 cm) 9-5/ (76.0 cm) -5/ (8.7 cm) 5-/ (4.0 cm) 0 (5.4 cm) dia. 0 9-/4 9-/ (.5 cm) (4. cm) 8-/8 (. cm) 4 W. 4 W. -7/8 (60.6 cm) 9-7/8 (75.9 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 47-7/8 (.6 cm) 5-7/8 (6.8 cm) 59-7/8 (5. cm) 65-7/8 (67. cm) 4 W. 4 W. -5/ (0. cm) 4-5/ (7.9 cm) 7-5/ (45.6 cm) 0-5/ (5. cm) -5/ (60.8 cm) 6-5/ (68.4 cm) 9-5/ (76.0 cm) -5/ (8.7 cm) 9-/4 (4.8 cm) 0 (5.4 cm) dia. 0 -/ (6.5 cm) 6-5/8 (6.8 cm) (7.6 cm) 4 W. 4 W. -7/8 (60.6 cm) 9-7/8 (75.9 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 47-7/8 (.6 cm) 5-7/8 (6.8 cm) 59-7/8 (5. cm) 65-7/8 (67. cm) 00 FM Interior entilar Installation for all Wall Hoods 00 or 500 FM Exterior entilar Installation for all Wall Hoods 0

7 Dimensions & Specifications (WH 8 H. T-Series Wall Hoods, 48, & 60 ) learance Dimensions (WH 8 H. T-Series Wall Hoods) Seal joints with silicone. Provided on T Series only. (5. cm) (0.5 cm) 8 (45.7 cm) 8 (45.7 cm) DIM X + 4-/ (.4 cm) (Hood width) 5-7/8 (9. cm) 48 W. 47-7/8 (.6 cm) 59-7/8 (5. cm) 7 (68.6 cm) 6 min. (67.6 cm) 7 max. (8.9 cm) 7 (68.6 cm) 0 min. (76. cm) max. (9.4 cm) NOTE: Optional duct cover sold separately. WH 8 H. T-Series Wall Hoods Description Duct cover width 5-7/8 (9. cm) 47-7/8 (.6 cm) 59-7/8 (5. cm) Duct cover depth (0.5 cm) Duct cover height (0.5 cm) Number of lights 4 Number of filters 4 Interior ventilar kits IN00* IN00* IN00* Exterior ventilar kits DE00*/500** DE00*/500** DE00*/500** In-line ventilar kits DIL00 DIL00 DIL00 Interior duct size 0 (5.4 cm) Exterior duct size 0 (5.4 cm) Interior Maximum amps Exterior Maximum amps 6./ /9. 8.8/9.5 In-Line Maximum amps *,00 FM interior- or exterior-power ventilar should be used with all T-Series models and when indoor models are installed over range/rangep with gas char-grill. Max duct run is 50 ft. ** It is recommended that the,500 FM ventilar be used with longer duct runs. Max duct run is 75 ft. NOTE: Maximum amp rating for hoods includes recommended ventilar kit rating; ll products must be hard wired with - wire with ground. n interior- or exterior-power ventilar kit must be purchased for installation with all 8 H. hoods. (9.4 cm) Note: T-Series Models must be installed in a covered, non-enclosed area, and should be protected from the elements as much as possible. The botm of the hood should be 0 (76. cm) (9.4 cm) above the grill surface. The hood should be installed 4-/ (.4 cm) plus the distance between the back trim and surface from the back wall. (Note: There is a minimum clearance from the back trim non-combustible surfaces, and a 4 minimum combustible surfaces.) This will require building the hood out from the wall. ny combustible material used for this purpose must be covered with locally-supplied stainless steel. iking also recommends using a backsplash.

8 Dimensions & Specifications (WH himney Wall Hoods 0,, 4, 48, 54, 60, & 6) learance Dimensions (WH himney Wall Hoods) (Duct width) (0.5 cm) (0.5 cm) 4 W. (0.5 cm) 48 W. 8 (45.7 cm) 8 (45.7 cm) 4 (6.0 cm) 4 (6.0 cm) (Hood width) 9-7/8 (76. cm) 5-7/8 (9. cm) 4 W. 4-7/8 (06.4 cm) 48 W. 47-7/8 (.6 cm) 5-7/8 (6.8 cm) 59-7/8 (5. cm) 65-7/8 (67. cm) NOTE: Optional duct cover sold separately. (5. cm) 4 (6.0 cm) WH himney Wall Hoods (0.5 cm) 4 (6.0 cm) 8 (45.7 cm) Description Duct cover width (0.5 cm) (0.5 cm) (0.5 cm) 8 (45.7 cm) 8 (45.7 cm) 4 (6.0 cm) 4 (6.0 cm) Duct cover depth (0.5 cm) Duct cover height (0.5 cm) 4 (6.0 cm) Number of lights 4 4 Number of filters Heat lamps Interior ventilar kits IN00/600 IN00/600 IN600 IN00* IN00* IN00* IN00* Exterior ventilar kits DE900/ 00* DE900/ 00* DE900/ 00* DE00*/ 500** DE00*/ 500** DE00*/ 500** *,00 FM interior- or exterior-power ventilar should be used when installed over range/rangep with gas char-grill. Max duct run is 50 ft. ** It is recommended that the,500 FM ventilar be used with longer duct runs. Max duct run is 75 ft. NOTE: Maximum amp rating for hoods includes recommended ventilar kit rating; ll products must be hard wired with - wire with ground. n interior- or exterior-power ventilar kit must be purchased for installation with all 8 H. hoods. DE00*/ 500** In-line ventilar kits DIL900/00 DIL900/00 DIL900/00 DIL00 DIL00 DIL00 DIL00 Interior duct size 7 (7.8 cm) 7 (7.8 cm) 7 (7.8 cm) 0 (5.4 cm) 0 (5.4 cm) 0 (5.4 cm) 0 (5.4 cm) Exterior duct size 0 (5.4 cm) Interior Maximum amps 4.9/ / Exterior Maximum amps 8.7/ / / /9. 8.5/9. 8.5/9. 8.5/9. In-Line Maximum amps 6.0/ / / (9.4 cm) 6min. (67.6 cm) 7 max. (8.9 cm) 0 min. (76. cm) max. (9.4 cm) 4 5

9 Interior entilar Dimensions (WH himney Wall Hoods) Exterior entilar Dimensions (WH himney Wall Hoods) (0.5 cm) -/ (.8 cm) 0 power supply (0.5 cm) -/ (.8 cm) 0 power supply 4 W. 4-5/ (7.9 cm) 7-5/ (45.6 cm) 0-5/ (5. cm) 8 (0. cm) -/ (.8 cm) 4 W. 4-5/ (7.9 cm) 7-5/ (45.6 cm) 0-5/ (5. cm) 8 (0. cm) -/ (.8 cm) 4 W. 9-7/8 (75.9 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 7 (7.8 cm) dia. 4 W. 9-7/8 (75.9 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 0 (5.4 cm) dia. 00 or 600 FM Interior entilar Installation for 0,, & 4 models 900 or 00 FM Exterior or In-Line entilar Installation for 0,, & 4 models -/ (.8 cm) 0 power supply -/ (.8 cm) 0 power supply -5/ (60.8 cm) 6-5/ (68.4 cm) 9-5/ (76.0 cm) -5/ (8.7 cm) (5. cm) -/ (.8 cm) 8 (45.7 cm) 8 (45.7 cm) 4 (6.0 cm) 4 (6.0 cm) -5/ (60.8 cm) 6-5/ (68.4 cm) 9-5/ (76.0 cm) -5/ (8.7 cm) (5. cm) -/ (.8 cm) 8 (45.7 cm) 8 (45.7 cm) 4 (6.0 cm) 4 (6.0 cm) 47-7/8 (.6 cm) 5-7/8 (6.8 cm) 59-7/8 (5. cm) 65-7/8 (67. cm) 0 (5.4 cm) dia. 47-7/8 (.6 cm) 5-7/8 (6.8 cm) 59-7/8 (5. cm) 65-7/8 (67. cm) 0 (5.4 cm) dia. 00 FM Interior entilar Installation for 48, 54, 60, & 6 models 900, 00 or 500 FM Exterior or In-Line entilar Installation for 48, 54, 60, & 6 models 6 7

10 Dimensions & Specifications (IH Island Hoods, 4, 54, & 6) learance Dimensions (IH Island Hoods) (5. cm) (0.5 cm) 8 (45.7 cm) (Hood width) 5-7/8 (9. cm) 4 W. 4-7/8 (06.4 cm) 5-7/8 (6.8 cm) 65-7/8 (67. cm) NOTE: Optional duct cover sold separately. 0 (76. cm) 6min. (67.6 cm) 7 max. (8.9 cm) 0 min. (76. cm) IH Island Hoods Description Duct cover width 5-7/8 (9. cm) 4-7/8 (06.4 cm) 5-7/8 (6.8 cm) 65-7/8 (67. cm) Duct cover depth (0.5 cm) Duct cover height (0.5 cm) Number of lights (9.4 cm) max. (9.4 cm) Number of filters Heat lamps N/ Interior ventilar kits IN600/00* IN600/00* IN00* IN00* Exterior ventilar kits DE900/00* DE900/00*/500** DE00*/500** DE00*/500** In-line ventilar kits DIL900/00 DIL900/00 DIL00 DIL00 Interior duct size 7 (7.8 cm)/ 0 (5.4 cm) 7 (7.8 cm)/ 0 (5.4 cm) 0 (5.4 cm) 0 (5.4 cm) Exterior duct size 0 (5.4 cm) Interior Maximum amps 4.6/ / Exterior Maximum amps 7.4/ /4.7/ /6. 6./7. In-Line Maximum amps 4.7/ / *,00 FM interior- or exterior-power ventilar should be used when installed over range/rangep with gas char-grill. Max duct run is 50 ft. ** It is recommended that the,500 FM ventilar be used with longer duct runs. Max duct run is 75 ft. NOTE: Maximum amp rating for hoods includes recommended ventilar kit rating; ll products must be hard wired with - wire with ground. n interior- or exterior-power ventilar kit must be purchased for installation with all 8 H. hoods. 8 9

11 Interior entilar Dimensions (IH Island Hoods) Exterior entilar Dimensions (IH Island Hoods) 4 W. 4 W. 7-5/ (45.6 cm) 0-5/ (8. cm) 6-5/ (68.4 cm) -5/ (8.7 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 5-7/8 (6.8 cm) 65-7/8 (67. cm) 4-5/8 (.7 cm) 7 (7.8 cm) dia. 8-/4 (47.6 cm) 9-/8 (.8 cm) 0 9-5/8 (4.4 cm) 5/8 (.6 cm) 9-/8 (. cm) 4 W. 4 W. 7-5/ (45.6 cm) 0-5/ (8. cm) 6-5/ (68.4 cm) -5/ (8.7 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 5-7/8 (6.8 cm) 65-7/8 (67. cm) 5-5/ (5. cm) 9-/4 (4.8 cm) -/ (.7 cm) 0 (5.4 cm) dia. 8-/4 (0.9 cm) 0 6-7/ (6.4 cm) -/ (6.5 cm) (7.6 cm) 600 FM Interior entilar Installation for all Island Hoods 900 or 00 FM Exterior or In-Line entilar Installation for all Island Hoods 4 W. 4 W. 7-5/ (45.6 cm) 0-5/ (8. cm) 6-5/ (68.4 cm) -5/ (8.7 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 5-7/8 (6.8 cm) 65-7/8 (67. cm) 8-/8 (50.0 cm) 5-/ (4 cm) 8-/8 (. cm) 0 0 (5.4 cm) dia. 9-/4 (.5 cm) 9-/8 (.8 cm) 9-/ (4. cm) 8-/4 (47.6 cm) 4 W. 4 W. 7-5/ (45.6 cm) 0-5/ (8. cm) 6-5/ (68.4 cm) -5/ (8.7 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 5-7/8 (6.8 cm) 65-7/8 (67. cm) 5-5/ (5. cm) 9-/4 (4.8 cm) 0 (5.4 cm) dia. 8-/ (0.7 cm) 0 -/ (6.5 cm) 6-5/8 (6.5 cm) (7.6 cm) 00 FM Interior entilar Installation for all Island Hoods 900, 00 or 500 FM Exterior or In-Line entilar Installation for all Island Hoods 0

12 Dimensions & Specifications (IH himney Island Hoods, 4, 54, & 6) learance Dimensions (IH himney Island Hoods) 4 W. (Duct width) (0.5 cm) (0.5 cm) 8 (45.7 cm) 4 (70.0 cm) 4 W. (Duct height) (0.5 cm) or 4 (6.0 cm) or (9.4 cm) 6 (5. cm) 8 (45.7 cm) (Hood width) 5-7/8 (9. cm) 4 W. 4-7/8 (06.4 cm) 5-7/8 (6.8 cm) 65-7/8 (67. cm) NOTE: Optional duct cover sold separately. 0 (76. cm) IH himney Island Hoods Description Duct cover width (0.5 cm) (0.5 cm) 8 (45.7 cm) 4 (70.0 cm) Duct cover depth (0.5 cm) Duct cover height (0.5 cm) or 4 (6.0 cm) or (9.4 cm) Number of lights (9.4 cm) 6min. (67.6 cm) 7 max. (8.9 cm) 0 min. (76. cm) max. (9.4 cm) Number of filters Heat lamps N/ Interior ventilar kits IN600 IN600 IN00* IN00* Exterior ventilar kits DE900/00* DE900/00*/500** DE00*/500** DE00*/500** In-line ventilar kits DIL900/00 DIL900/00 DIL00 DIL00 Interior duct size 7 (7.8 cm) 7 (7.8 cm) 0 (5.4 cm) 0 (5.4 cm) Exterior duct size 0 (5.4 cm) Interior Maximum amps Exterior Maximum amps 7.4/ /4.7/ / /7.4 In-Line Maximum amps 4.7/6.5.9/ *,00 FM interior- or exterior-power ventilar should be used when installed over range/rangep with gas char-grill. Max duct run is 50 ft. ** It is recommended that the,500 FM ventilar be used with longer duct runs. Max duct run is 75 ft. NOTE: Maximum amp rating for hoods includes recommended ventilar kit rating; ll products must be hard wired with - wire with ground. n interior or exterior-power ventilar kit must be purchased for installation with all 8 H. hoods.

13 Interior entilar Dimensions (IH himney Island Hoods) Exterior entilar Dimensions (IH himney Island Hoods) (0.5 cm) -/8 (.9 cm) (0.5 cm) -/8 (.9 cm) 4 W. 4 W. 7-5/ (45.6 cm) 0-5/ (5. cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) (5. cm) 0 power supply -/8 (.9 cm) 4 W. 4 W. 7-5/ (45.6 cm) 0-5/ (5. cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) (5. cm) 0 power supply -/8 (.9 cm) 7 (7.8 cm) dia. 0 (5.4 cm) dia. 600 FM Interior entilar Installation for all himney Island Hoods 900 or 00 FM Exterior or In-Line entilar Installation for all himney Island Hoods 6-5/ (68.4 cm) -5/ (8.7 cm) 5-7/8 (6.8 cm) 65-7/8 (67. cm) 8 (45.7 cm) 4 (6.0 cm) (5. cm) 0 (5.4 cm) dia. -/8 (.9 cm) 0 power supply -/8 (.9 cm) 6-5/ (68.4 cm) -5/ (8.7 cm) 5-7/8 (6.8 cm) 65-7/8 (67. cm) 8 (45.7 cm) 4 (6.0 cm) (5. cm) 0 (5.4 cm) dia. -/8 (.9 cm) 0 power supply -/8 (.9 cm) 00 FM Interior entilar Installation for all himney Island Hoods 900, 00 or 500 FM Exterior or In-Line entilar Installation for all himney Island Hoods 4 5

14 Dimensions & Specifications ( Wall usm entilar System 0,, 4, 48, 54, 60 & 6) * Installing Hood anopy (usm Hood anopy uuts) *For best results, center the unit over the burners of the cooking product (front back; right left). * Make sure the back wall of the cusm hood canopy is flush with the cuut so the ventilar system may be mounted as shown on page 5. usm Hood anopy otm uut Dimensions Wall Hoods Description (Hood Width) (Hood Depth) 0 W. 7-7/ (69.7 cm) -7/ (54.5 cm) W. -7/ (84.9 cm) -7/ (54.5 cm) 4 W. 9-7/ (00. cm) -7/ (54.5 cm) 48 W. 45-7/ (5.4 cm) -7/ (54.5 cm) 54 W. 5-7/ (0.7 cm) -7/ (54.5 cm) 60 W. 57-7/ (45.9 cm) -7/ (54.5 cm) 6 W. 6-7/ (6. cm) -7/ (54.5 cm) Wall usm entilar System Description Number of lights 4 4 Number of filters 4 4 Heat lamps Interior ventilar kits IN00/ 600/00* IN00/ 600/00* IN600/ 00* IN00* IN00* IN00* IN00* Exterior ventilar kits DE900/ 00* DE900/ 00* DE900/ 00* DE00*/ 500** DE00*/ 500** DE00*/ 500** DE00*/ 500** In-line ventilar kits DIL900/00 DIL900/00 DIL900/00 DIL00 DIL00 DIL00 DIL00 Interior duct size 7 /0 (7.8/5.4 cm) 7 /0 (7.8/5.4 cm) 7 /0 (7.8/5.4 cm) 0 (5.4 cm) 0 (5.4 cm) 0 (5.4 cm) 0 (5.4 cm) Exterior duct size 0 (5.4 cm) Interior Maximum amps 5.9/ / / Exterior Maximum amps 8.7/ / / /9. 8.5/9. 8.9/9. 8.9/9. In-Line Maximum amps 6.0/ / / *,00 FM interior- or exterior-power ventilar should be used when installed over range/rangep with gas char-grill. Max duct run is 50 ft. ** It is recommended that the,500 FM ventilar be used with longer duct runs. Max duct run is 75 ft. NOTE: Maximum amp rating for hoods includes recommended ventilar kit rating; ll products must be hard wired with - wire with ground. n interior- or exterior-power ventilar kit must be purchased for installation with all 8 H. hoods. ) Position ventilar system inside of the cusm hood canopy and center it front back and left right. ) otm mounting holes fasten ventilar system botm of cusm hood canopy with the screws provided. uilt-in entilar System ) OPTIONL Rear mounting holes fasten ventilar system rear of cusm hood canopy. 6 7

15 learance Dimensions ( Wall usm entilar System) uilt-in Wall usm entilar System Dimensions ( Models) -/ (.8 cm) (.54 cm) -/ (.8 cm) 7/8 (. cm) (usm Hood) -/ (9. cm) 7-/4 (4.8 cm) 5/8 (.6 cm) (5. cm) 5/8 (.6 cm) (9.4 cm) 6min. (67.6 cm) 7 max. (8.9 cm) 0 min. (76. cm) max. (9.4 cm) 5-/ (4.0 cm) -7/8 (55.8 cm) For 900, 00 or 500 FM Exterior or In-Line entilar Installation 0 (5.4 cm) dia. 8-/4 (0.9 cm) D (5. cm) 4-5/8 (.7 cm) -7/8 (55.8 cm) For 00, 600 or 00 FM Interior entilar Installation 9-/8 (.8 cm) 0 7 (7.6 cm) 0 (7.8 cm) dia. duct location 9-5/8 (4.4 cm) -/ (6.4 cm) 8-/4 (47.6 cm) D 9-/4 (.5 cm) 5/8 (.6 cm) 5/8 (.6 cm) 900 or 00 FM Exterior or In-Line entilar Installation 0,, 4 W. Models 00 or 600 FM Interior entilar Installation 0,, 4 W. Models *Note: Dotted Line (...) represents cuut. 0 W. 8-/4 (7.8 cm) W. 4-/4 (87.0 cm) 4 W. 40-/4 (0. cm) D 0 W. 4-/8 (5.9 cm) W. 7-/8 (4.5 cm) 4 W. 0-/8 (5. cm) 8 9

16 uilt-in Wall usm entilar System Dimensions ( Models) Dimensions & Specifications (I Island usm entilar System, 4, 54 & 6) 8-/4 (0.9 cm) D * 5-/ (4.0 cm) (5. cm) 0 (5.4 cm) dia. 5/8 (.6 cm) 0 (7.6 cm) -/ (6.4 cm) *For best results, center the unit over the burners of the cooking product (front back; right left). * Make sure the back wall of the cusm hood canopy is flush with the cuut so the ventilar system may be mounted as shown on page or 500 FM Exterior or In-Line entilar Installation 48, 54, 60, 6 W. Models otm uut Dimensions 5-/ (4.0 cm) 0 (5.4 cm) dia. duct location 5/8 (.6 cm) 8-/ (50.0 cm) 9-/4 (.5 cm) 9-/8 (.8 cm) 0 9-/ (4.4 cm) D 8-/8 (. cm) Island Hoods Description (Hood Width) (Hood Depth) W. -7/ (84.9 cm) 7-9/ (70.0 cm) 4 W. 9-7/ (00. cm) 7-9/ (70.0 cm) 54 W. 5-7/ (0.7 cm) 7-9/ (70.0 cm) 6 W. 6-7/ (6. cm) 7-9/ (70.0 cm) I Island usm entilar System Description Number of lights Number of filters FM Interior entilar Installation 0,, 4, 48, 54, 60, 6 W. Models *Note: Dotted Line (...) represents cuut. Heat lamps N/ Interior ventilar kits IN600/00* IN600/00* IN00* IN00* Exterior ventilar kits DE900/00* DE900/00*/500** DE00*/500** DE00*/500** In-line ventilar kits DIL900/00 DIL900/00 DIL00 DIL00 Interior duct size 7 (7.8 cm)/ 7 (7.8 cm)/ 0 (5.4 cm) 0 (5.4 cm) 0 (5.4 cm) 0 (5.4 cm) 0 W. 8-/4 (7.8 cm) W. 4-/4 (87.0 cm) 4 W. 40-/4 (0. cm) 48 W. 46-/4 (7.5 cm) 54 W. 5-/4 (.7 cm) 60 W. 58-/4 (48.0 cm) 6 W. 64-/4 (6. cm) D 0 W. 4-/8 (5.9 cm) W. 7-/8 (4.5 cm) 4 W. 0-/8 (5. cm) 48 W. -/8 (58.7 cm) 54 W. 6-/8 (66.4 cm) 60 W. 9-/8 (74.0 cm) 6 W. -/8 (8.6 cm) Exterior duct size 0 (5.4 cm) Interior Maximum amps 4.6/ / Exterior Maximum amps 7.4/ /4.8/ /6. 5.6/6. In-Line Maximum amps 4.7/ / *,00 FM interior- or exterior-power ventilar should be used when installed over range/rangep with gas char-grill. Max duct run is 50 ft. ** It is recommended that the,500 FM ventilar be used with longer duct runs. Max duct run is 75 ft. NOTE: Maximum amp rating for hoods includes recommended ventilar kit rating; ll products must be hard wired with - wire with ground. n interior- or exterior-power ventilar kit must be purchased for installation with all 8 H. hoods. 0

17 Installing Hood anopy (usm Hood anopy uuts) learance Dimensions (I Island usm entilar System) usm Hood anopy (usm Hood) 6min. (67.6 cm) 7 max. (8.9 cm) 0 min. (76. cm) ) Position ventilar system inside of the cusm hood canopy and center it front back and left right. ) otm mounting holes fasten ventilar system botm of cusm hood canopy with the screws provided. uilt-in entilar System (9.4 cm) max. (9.4 cm) ) OPTIONL Rear mounting holes fasten ventilar system rear of cusm hood canopy.

18 uilt-in Island usm entilar System Dimensions (I Models) uilt-in Island usm entilar System Dimensions (I Models) -/ (.8 cm) (.5 cm) -/ (.8 cm) / (.7 cm) 8-/4 (47.6 cm) 5/8 (.6 cm) -/ (9. cm) 7-7/ (69.7 cm) (including screw heads) 8-7/ (7. cm) External Power (5. cm) 5/8 (.6 cm) -/ (9. cm) 7-7/ (69.7 cm) (including screw heads) 8-7/ (7. cm) Internal Power 7-/4 (4.8 cm) 5-/4 (4.6 cm) 0 (5.4 cm) dia. 5/8 (.6 cm) 8-/4 (.0 cm) 0 -/ (6.4 cm) (5. cm) (7.6 cm) 900, 00 or 500 External or In-Line Power 4, 54, 6 W. Models 5-/ (4.0 cm) 0 (5.4 cm) dia. duct location 5/8 (.6 cm) 9-/4 (.5 cm) 0 9-/ (4.4 cm) 8-/4 (47.6 cm) 00 FM Internal Power 4, 54, 6 W. Models 7/8 (. cm) 8-/8 (. cm) 5-/4 (4.6 cm) 8-/4 (.0 cm) 0 (5. cm) (7.6 cm) -/ (.0 cm) 5-/ (. cm) 8-/4 (47.6 cm) 9-/8 (.8 cm) 0 9-/4 (.5 cm) 54 W. 5-/4 (.7 cm) 6 W. 64-/4 (6. cm) *Note: Dotted Line (...) represents cuut. 54 W. 6-/8 (66.4 cm) 6 W. -/8 (8.6 cm) 0 (5.4 cm) dia. -/ (6.4 cm) 7 (7.8 cm) dia. 9-5/8 (4.4 cm) 5/8 (.6 cm) 900 or 00 FM External or In-Line Power, 4 W. Models W. 4-/4 (87.0 cm) 4 W. 40-/4 (0. cm) 5/8 (.6 cm) 600 FM Internal Power, 4 W. Models *Note: Dotted Line (...) represents cuut. W. 7-/8 (4.5 cm) 4 W. 0-/8 (5. cm) 4 5

19 Planning Information Installation (WH 0 H. Wall Hoods w/standard entilar) Proper installation of ducting is extremely important ensure maximum performance from any ventilation product. ll FMs are based on tests at 0. static pressure: without applying static pressure, FM would be greatly overstated. Straight runs and gradual turns are best; for example, each 90º elbow is equivalent 5-0 feet ( cm) of straight run. Never use flexible duct; it creates back pressure/air turbulence and greatly reduces performance. Proper performance is dependent on proper ducting; make sure that a qualified and trained installer is used. heck with a qualified and trained installer or local codes for makeup air requirement, if any. Max. amp rating for hoods includes recommended ventilar kit rating; all products must be hard wired direct with -wire with ground. Roof cap 7 round duct Roof cap 0 round duct 00 or 600 FM single blower interior-power typical ductwork Duct cover or soffit Hood 00 FM single blower interior power typical ductwork Duct cover or soffit 4 5/ nut driver heck damper for unrestricted movement, adjust if necessary. ttach transition damper. Seal with aluminum tape. W R N I N G To reduce the risk of fire, electric shock, or injury persons, observe the following: Plan where the duct work will be located. Install proper-sized duct work, and roof or wall cap for the type of blower you are using. Recommended hood locations for the most common installations are shown. djust your measurements for various heights of ceilings, soffits, cabinets, or ranges/rangeps. heck Framing Exterior blower 0 round duct Hood 900, 00, or 500 FM exterior power typical ductwork Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. efore servicing or cleaning unit, switch power off at service panel and lock service panel prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, the service panel. Duct cover or soffit Flip hood over and remove electrical box cover. Hood Wall cap Wall Installation exterior power typical ductwork 4 5 Duct Duct cover or soffit Hood NOTE: ecause of the weight of the hood make sure that the mounting screws are driven in the framing and not just the drywall. It may be necessary drill additional holes in the canopy for proper alignment. NOTE: Wall exhaust must be a minimum of 4 (6.0 cm) from ground. This may vary depending on local codes and geographic location. Electrical Supply Run 0 electrical wiring from service panel installation location. See Specifications pages for the maximum amp requirements. Insert of electrical wiring through the p of vent hood and secure using wiring restrain. Refer local codes. Slide duct over transition and tape around joint. 6 7

20 6 5/ nut driver 5/ nut driver UTION: Secure vent hood wall using screws provided. Use additional mounting screws and wall anchors, if necessary. 7 RE OR GREEN UTION: If not using a duct cover, using screws provided, make sure p mounting screws are secured in soffit or cabinet framing. Use additional mounting screws, if necessary. 8 Slide filter front over front lip. Push filter rear up, then slide back over rear lip. Duct over Option (WH 0 H. Wall Hoods w/standard entilar) WHITE GREEN LK WHITE LK onnect black black, white white, and the green/bare wire under the green screw. NOTE: Housing wiring must be properly installed for wiring be correct when wiring unit. Replace electrical box cover. Make connection breaker box. Measure distance from ceiling canopy. Installation (WH 0 H. Wall Hoods w/recirculating Kit) Slide the duct cover in place and fasten from inside canopy using the sheet metal screws provided. 9 0 Slide filter front over front lip. Push filter rear up, then slide back over rear lip. Slide spacer front over front lip. Push spacer rear up, then slide back over rear lip. Remove damper and discard with transition. Turn recirculating unit upside down. Place vent hood upside down on recirculating unit. 8 9

21 4 8 RE OR GREEN 9 WHITE GREEN LK WHITE LK ttach with screws and lock washers provided. ttach with screws. onnect black black, white white, and the green/bare wire under the green screw. NOTE: Housing wiring must be properly installed for wiring be correct when wiring unit. Replace electrical box cover. Make connection breaker box. 5 W R N I N G To reduce the risk of fire, electric shock, or injury persons, observe the following: 0 Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. efore servicing or cleaning unit, switch power off at service panel and lock service panel prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, the service panel. Remove electrical box cover. ssemble brackets baffles and insert charcoal filters. Slide filter front over front lip. Push filter rear up, then slide back over rear lip / nut driver Flip hood over. Insert of electrical wiring through the p of vent hood and secure. Refer local codes. UTION: Secure vent hood. Make sure mounting screws are secured in framing. Use additional mounting screws and wall anchors, if necessary. Slide spacer front over front lip. Push spacer rear up, then slide back over rear lip. Slide filter front over front lip. Push filter rear up, then slide back over rear lip. 40 4

22 Installation (WH 8 H. Wall & WH himney Wall Hoods) -/ x /4 (.8 cm) x (.9 cm) wood strip -/ (4.6 cm) 5/ nut driver Slot for wood strip 5/ nut driver 5 6 Measure down -/6 (4.6 cm) from desired height of hood and secure -/ x /4 wood strip (provided locally) wall using screws provided. 5/ nut driver Use additional mounting screws secure hood wood strip. 5/ nut driver Slide spacer front over front lip. Push spacer rear up, then slide back over rear lip. Duct over Option (WH 8 H. Wall Hoods) Slide filter front over front lip. Push filter rear up, then slide back over rear lip. UTION: Secure vent hood wall using screws provided. Use additional mounting screws and wall anchors, if necessary. UTION: If not using a duct cover, using screws provided, make sure p mounting screws are secured in soffit or cabinet framing use additional mounting screws, if necessary. Measure distance from ceiling canopy. Slide the duct cover in place and fasten from inside canopy using the sheet metal screws provided. 4 To install ventillation kit refer ventillation kit installation instructions. Slide filter front over front lip. Push filter rear up, then slide back over rear lip. 4 4

23 Duct over Option (WH himney Wall Hoods) Installation (IH/IH Island Hoods) Measure distance from ceiling canopy. Tape avoid scratching. heck framing where cuut will be. NOTE: 00 lb. limit. ut appropriate size hole in ceiling. Either 7 or 0 depending on your specific unit and ventillar kit. 4 Mounting options: Using duct cover with ceiling mounting bracket. (Option - IH only) Using threaded rod for additional support. (Option ) ttaching hood directly soffit or duct cover. (Skip step ) Place duct cover p inside duct cover base and lower until desired height is found. Mark height. Use the retaining nuts and bolts fasten in place and remove tape. Slide the duct cover in place and fasten from inside canopy using the sheet metal screws provided. ttach duct cover optional ceiling mounting bracket. 5/ nut driver ttach duct cover ceiling. The ceiling bracket can be hidden by using a locally supplied trim. dditional support option. Drill holes in all four corners for threaded rod and run rods from hood ceiling

24 4 5/ nut driver Service & Registration Service & Parts Only authorized replacement parts may be used in performing service on the appliance. Do not repair or replace any part of the appliance unless specifically recommended in the manual. ll other servicing should be referred a qualified technician. Run duct work down botm edge of duct cover/soffit and secure in place. Make sure the duct does not stick down past the cover. To install ventillation kit refer ventillation kit installation instructions. ttach canopy duct cover/soffit. Seal p of hood duct with aluminum tape. 5 Record the following information indicated below. You will need it if service is ever required. The serial number and model number for your appliance are located on the identification plate mounted on the inside of the hood canopy. Model number Serial number Date of purchase Slide filter front over front lip. Push filter rear up, then slide back over rear lip. 6 7 Date installed Dealer's name ddress Slide spacer front over front lip. Push spacer rear up, then slide back over rear lip. NOTE: Number of spacers and baffles may vary by model. Slide filter front over front lip. Push filter rear up, then slide back over rear lip