Service 5. Workshop Manual FABIA Body Work Edition Service Department. Technical Information. Printed in Czech Republic S

Transcription

1 Service 5 Workshop Manual FABIA 2000 Body Work Edition Service Department. Technical Information Printed in Czech Republic S

2 5 Service The Workshop Manual is intended only for use within the Organisation Škoda. It is not permitted to pass it on to other persons. Printed in Czech Republic S ŠKODA AUTO a. s.

3 List of Supplements to Workshop Manual FABIA 2000 Body Work Edition Supplement Edition Subject Article Number Basic Edition S Supplement to Basic Edition S Self-diagnosis for convenience system S Final diagnosis for airbag S Supplement to Rep. - Gr S Supplement to Rep. - Gr S Supplement to Rep. - Gr S Supplement to Rep. - Gr S Supplement to Rep. - Gr. 01 and 64 S Fabia Praktik S Supplement to Rep. - Gr. 70 and 72 S Supplement to Rep. - Gr S Supplement to Rep. - Gr. 70 S Supplement to Rep. - Gr S Supplement to Rep. - Gr. 01, 57, 58 and 69 S Self-diagnosis for convenience system with LIN databus cable and Supplement to Rep. - Gr. 55, 57, 58, 63, 68, 69 and 70 Edition List of Supplements

4 List of Supplements Edition 01.05

5 Table of Contents 00 Technical Data Technical Data... - Vehicle identification data Self-diagnosis Self-diagnosis for convenience system Notes concerning self-diagnosis for convenience system Types and description of convenience system Overview of the selectable functions of the diagnosis for the convenience system Connect vehicle system tester -V.A.G Interrogating control unit version Interrogating fault memory Actuator diagnosis Erasing fault memory Ending output Coding control unit Self-diagnosis for convenience system with CAN databus cable Overview of the selectable functions of the self diagnosis for convenience system with CAN 1 databus cable Overview of the control units for convenience system with CAN databus cable Coding control unit with CAN databus cable Fault table Convenience system with CAN databus cable Reading measured value block for convenience system with CAN databus cable Test table for convenience system with CAN databus cable Self-diagnosis for convenience system with LIN databus cable Overview of the selectable functions of the self-diagnosis for convenience system with LIN 1 databus cable Overview of the control units for convenience system with LIN databus cable Coding control unit with LIN databus coding Fault table of control unit for convenience system with LIN databus cable Fault table of LIN databus/control units for window control in the individual doors Reading measured value block with LIN databus cable Test table with LIN databus cable Adapting the convenience system ( for all convenience system types) Adjustment Self-diagnosis for Airbag System I Function of the airbag system Connect vehicle system tester -V.A.G and select address word Airbag Overview of selectable functions Interrogating control unit version Interrogating fault memory Actuator diagnosis Erasing fault memory Ending output Coding airbag control unit Self-diagnosis for airbag system II Edition Table of Contents I

6 - Fault table Reading measured value block Test table Parts inspection with test box -VAS Deactivating and activating airbag units (adaptation)... - Deactivating and activating passenger-side airbag units (adaptation) Front body Front body Removing and installing lock carrier with component parts Front wing Removing and installing the front wing Bonnet, tailgate Front bonnet... - Summary of front bonnet components Summary of radiator grill components Disassembling and assembling radiator grill Adjusting front bonnet Tailgate... - Removing the pressurized gas strut... - Degassing the pressurized gas strut... - Summary of components of tailgate lock... - Summary of components of remote release Removing and installing luggage compartment lid hinges (Sedan) Adjusting luggage compartment lid Fuel-tank lid unit Summary of components of the fuel-tank lid unit Front doors/door internal parts/central locking Front door Summary of components Removing and installing the door... - Door adjustment... - Removing and installing assembly carrier... - Removing and installing door window... - Removing and installing window lifter motor... - Summary of components of door handle and door lock... - Removing and installing the lock cylinder housing... - Removing and installing the door handle Removing and installing the door lock Removing and installing the locking button for locking rod Summary of components of front door seals Central locking system Rear doors/door internal parts Rear door Summary of components Removing and installing the door II Table of Contents Edition 01.05

7 - Door adjustment Summary of components of door handle and door lock Removing and installing the door handle Removing and installing the door lock Removing and installing assembly carrier Removing and installing door window Summary of components of door seals Rear door (Praktik) Rear door...summary of components Removing and installing the door lock Sliding/tilting roof Sliding/tilting roof with glass panel Summary of components of sliding/tilting roof with glass panel Removing and installing the glass roof Removing and installing sun screen Removing and installing E-drive Setting E-drive (0 position) Adapting drive Inspecting parellel run Setting parallel run Removing and installing assembly unit Cleaning the water drain hoses Bumpers Front bumper Summary of components on the front bumper Summary of components on the front bumper (RS) Removing and installing the bumper bracket Rear bumper Summary of components of rear bumper Removing and installing the bumper bracket Removing and installing rear apron (RS) Glazing Glued windows Removing and installing glued windows Removing and installing side window (Combi) Prepare new windscreen for fitting Prepare flange for fitting Glueing Waiting time Eliminating paint damage Remove glue and clean Exterior equipment Wheelhouse liner Removing and installing the front wheelhouse liner Removing and installing the rear wheelhouse liner Edition Table of Contents III

8 Rear-view mirror Summary of components of rear-view mirror Water box cover... - Removing and installing water box cover... Roof drip moulding... - Removing and installing roof drip moulding... Protective strips... - Removing and installing protective side strips... Trailer coupling... - Summary of components trailer coupling... Roof railing (Combi)... - Removing and installing the roof rack... Rear spoiler Summary of the components - for the complete rear spoiler (Combi) Removing and installing rear spoiler completely (Combi) Summary of the components - for the complete rear spoiler (RS) Removing and installing rear spoiler completely (RS)... Decorative strips (Combi)... - Removing and installing decorative strips Interior equipment Interior rear-view mirror Removing interior rear-view mirror Installing rear-view mirror Repair method with glass-metal adhesive Covers, storage areas and trim panels Summary of components of centre console Removing and installing the front can holder Removing and installing the sun visor Removing and installing the centre sun visor... - Removing and installing the storage area (Praktik)... - Removing and installing the moulded headliner (Praktik)... Recessed handle... - Removing and installing recessed handle... Partition panel and protective grating (Praktik)... - Summary of components for the partition panel... - Removing and installing the protective grating for the tailgate... Floor partition (Praktik)... - Removing and installing the front floor partition... - Removing and installing the rear floor partition... Front entrance plates (RS) Removing and installing the front entrance plates Occupant protection Seat belts Safety instructions for work on seat belt tensioners Summary of components of front seat belts IV Table of Contents Edition 01.05

9 - Removing and installing the rear seat belts Summary of components - middle three-point seat belt at the rear Inspecting seat belts Checks Airbag Airbag system Safety precautions when working on the airbag system Replacing parts of the airbag system Removing and installing driver airbag unit Summary of components of four-armed steering wheel Summary of components of three-armed steering wheel Removing and installing restoring ring with slip ring Removing and installing passenger airbag unit Removing and installing a side airbag crash sensor Removing and installing side airbag units Removing and installing airbag control unit -J Removing and installing the front passenger airbag switch Removal of pyrotechnic parts before scrapping the vehicle Disposal of the airbag units before scrapping the vehicle Trim panel/insulation Dash panel Removing and installing the dash panel Removing and installing the central tube/dash panel Removing and installing the convenience system central control unit Door trim panels Summary of components of front door trim panels Removing and installing the front door trim panel Summary of components of rear door trim panels Removing and installing the rear door trim panel Removing and installing the rear door trim panel (Praktik) Pillar and side trim panels Removing and installing top trim panel of pillar A Removing and installing bottom trim panel of pillar A Summary of components of trim panels of pillar B Removing and installing bottom trim panel of pillar B Removing and installing top trim panel of pillar C Removing and installing bottom trim panel of pillar C Removing and installing top trim panel of pillar C (Fabia Combi) Removing and installing top trim panel of pillar D Removing and installing the base plate (notchback) Summary of components of entrance plate Removing and installing the tailgate/luggage compartment cover (Praktik) Door trim panels in the luggage compartment Summary of components of luggage compartment cover Summary of components of side trim panel of luggage compartment Removing and installing bases for luggage compartment floor Edition Table of Contents V

10 - Summary of components of rear cargo opening cover Summary of components of trim panels of tailgate Removing and installing holder for luggage compartment cover (estate car)... - Removing and installing the side luggage compartment trim panel (estate car)... - Removing and installing the bonnet at the rear (Praktik)... - Removing and installing the bonnet at the rear (Praktik) Removing and installing the finishing strip Moulded headliner Removing and installing moulded headliner Removing and installing the moulded headliner (Praktik)... - Summary of components of the moulded headliner noise insulation panels (Fabia Combi) Seat racks Front seats... - Removing and installing the front seats Removing and installing the grip for the seat height adjuster Removing and installing the backrest rack for the seat rack Removing and installing seat height adjusting elements... Rear seats... - Removing and installing seat bench and backrest... - Removing and installing the rear armrests Seat Upholstery, Covers Front seat upholstery and covers... - Assembly overview of covers and upholstery for front seats... - Assembly overview of covers and upholstery for backrests... Rear seat upholstery and covers... - Assembly overview of covers and upholstery for rear seats... - Assembly overview of covers and upholstery for rear backrest VI Table of Contents Edition 01.05

11 00 00 Technical Data 00-1 Technical Data Vehicle identification data Vehicle identification number The vehicle identification number (chassis number) is attached to the right suspension dome. The vehicle identification number (chassis number) can also be found bottom left of the front window corner. 1 - Manufacturer's world code 2 - Model and version 3 - Engine type 4 - Airbag system 5 - Vehicle type 6 - Internal code 7 - Model year 8 - Manufacturing plant 9 - Body number Note Detailed information on the meaning of individual signs Inspection and Maintenance, Chap Type plate The type plate -arrow- is attached to the left wheel house. Edition S Technical Data

12 00 FABIA 2000 Body Work Vehicle data sticker The vehicle data sticker is located at the rear left on the floor of the luggage compartment Technical Data Edition S

13 01 01 Self-diagnosis 01-1 Self-diagnosis for convenience system Notes concerning self-diagnosis for convenience system The central control unit for convenience system -J393- is located above the accelerator pedal in the dash panel. It is clipped into the bracket on the heating housing. The diagnostic connector is located behind the storage tray under the light switch. Removing and installing the control unit for convenience system Chap Initiate self-diagnosis at the start of fault finding and interrogate the fault memory with diagnostic device -V.A.G or -V.A.G or -VAS Note The description which follows relates to the vehicle system tester -V.A.G using program card (and higher version). The use of fault read-out scan tool -V.A.G with program card (and later version) is almost identical except for specific deviations (e.g. other display, possibility of using a printer etc.). To end the output or to switch to another address select function 06 End output. WARNING! When replacing the central control unit for the convenience system or the alarm system with an independent power supply disconnect the power supply for at least 30 sec. in order to allow the alarm to be adapted. If necessary, disconnect the communication cable. The convenience system can be adapted to the customer wish Chapter Types and description of convenience system Two different systems of databus cables are used in the convenience system: for vehicles manufactured until the CAN databus cable for vehicles manufactured as of the LIN databus cable The difference is the operation of the window control, the fault tables, the measured value blocks and the coding of the control unit. Edition Self-diagnosis for convenience system

14 01 FABIA 2000 Body Work In case of repairs or self-diagnosis of the convenience system first the system of the communication cable must be defined. This is detected by means of the connection of the diagnostic device and by entry of the address word 46 Central module convenience system Convenience system with CAN databus cable The convenience system comprises the electric equipment in the doors: electrical central locking system with SAFE function power-window lifter with jamming protection electrically adjustable and heated exterior mirror It also comprises other systems in the vehicle: Cut-off delay for interior lamp Monitoring and disconnection of all interior and luggage compartment lights as a battery discharge protection Sliding roof closing function via outside closing command Radio control for anti-theft alarm system and central locking the optical Safe function indicator (is a LED mounted in the door equipment of the driver's door) The system comprises the control unit for convenience system and control units in the individual doors whose communication between each other is performed via the CAN databus cable. The communication between the central control unit for convenience system and other electrical systems in the vehicle is performed via the CAN databus cable. The control unit for convenience system detects faults in the convenience system (including faults at control units in the individual doors) and stores them in a permanent memory. The displayed fault messages refer to a fault table including indications on the possible causes as well as targeted repairs. Faults due to a temporary line interruption or loose contact are also stored. These faults are displayed as sporadic faults SP. Convenience system with LIN databus cable The convenience system comprises the electric equipment in the doors: electrical central locking system with SAFE function power-window lifter with jamming protection It also comprises other systems in the vehicle: Self-diagnosis for convenience system Edition 01.05

15 01 Sliding roof closing function via outside closing command Radio control for anti-theft alarm system and central locking the optical Safe function indicator (is a LED mounted in the door equipment of the driver's door) The system comprises the control unit for convenience system. Its communication with other electrical systems in the vehicle is performed via the CAN databus cable. Control units are also located in the individual doors, which however only operate the window lifters. Their communication is performed via the LIN databus cable. The LIN databus cable is not self-diagnostic with any diagnostic device. This cable consists of an independent electrical circuit, which has no connection to other electrical systems in the vehicle. The control unit for convenience system detects faults in the convenience system (including faults in the individual doors relating to the lock) and stores them in a permanent memory. The faults relating to the window control can be stored in the fault memory of the convenience system. WARNING! If the window control is restricted or fully non-operational, proceed according to functionality of individual windows Chap. 01-3, Fault table LIN databus/control units for window control in the individual doors. This table is used for the diagnosis of faults from the LIN databus. Overview of the selectable functions of the diagnosis for the convenience system Operation Page 01 Interrogating control unit version 02 Interrogating fault memory 03 Actuator diagnosis Erasing fault memory Ending output Coding control unit Reading measured value block Chap. 01-2, Chap Adjustment Chapter 01-4 Edition Self-diagnosis for convenience system

16 01 FABIA 2000 Body Work Connect vehicle system tester -V.A.G Special tools, test and measuring equipment and auxiliary items required Vehicle system tester -V.A.G Diagnostic cable -V.A.G 1551/3, 3A, 3B, 3C- Test conditions All fuses must be OK in compliance with the current flow diagram. Battery voltage at least 9 V C O Q HELP V.A.G Procedure Open the storage tray -1- under the light switch -arrow-. Switch off ignition and connect vehicle system tester -V.A.G Switch on ignition. Select address word 46 Central module convenience system. Confirm the entry with key Q. Vehicle system test Enter address word XX Vehicle system test 46 Central module convenience system Vehicle system test Tester sends address word 46 HELP Q Note One of the following four displays will appear in the event of a communication set-up failure between vehicle system tester -V.A.G and the control unit. Press HELP key to display the possible fault causes. The ignition must be on! Vehicle system test The control unit does not respond HELP Malfunctions occurred at the start of or during the program (external sources of interference). Vehicle system test HELP K cable does not connect to pos. term. Check connection of the vehicle system tester -V.A.G After removing the possible fault causes re-enter address word 46 Central module convenience system and confirm entry with Q. Read-out on display after entering address word 46 : Vehicle system test No signal from the control unit Vehicle system test Fault in communication set-up Vehicle system test Tester sends address word 46 The display shows the control unit identification number, e.g.: Press key. 6Q C OM convenience unit 0002 Coding WSCXXXXX Self-diagnosis for convenience system Edition 01.05

17 01 The following display relates to the system with LIN databus cable: In this case continue the self-diagnosis Chap The following display relates to the system with CAN databus cable: Readout on display, e.g.: (Door control unit driver's side) In this case continue the self-diagnosis Chap Vehicle system test Select function XX 6Q OM D.contr unit DDCU HELP TFK 0001 Press key. Readout on display, e.g.: (Door control unit passenger's side) 6Q OM D.contr unit PDCU TFK 0001 Press key. Readout on display, e.g.: (Door control unit RL) Press key. Readout on display, e.g.: (RR door control unit) Press key. Interrogating control unit version Connecting vehicle system tester -V.A.G and selecting the address word for the convenience system Q OM D.contr unit RL 6Q OM D. contr unit RR Vehicle system test Select function XX Vehicle system test Select function XX TFK 0001 TFK 0001 HELP HELP Select function 01 and confirm entry with Q. Vehicle system test Q 01 - Interrogating control unit version The control unit identification appears in the display of the vehicle system tester -V.A.G e.g.: 6Q OM = Part No. of the control unit (current control unit version Electronic catalogue of original parts) Convenience unit = system description 0002; (TFK 0001) = Program number Coding = Coding variant WSC = Workshop code 6Q C OM convenience unit Coding WSC XXXXX Press key. Readout on display, e.g.: (Door control unit driver's side) Press key. Readout on display, e.g.: (Door control unit passenger's side) Press key. Readout on display, e.g.: (Door control unit RL) 6Q OM 6Q OM 6Q OM door control.dd TFK 0001 door control.pd TFK 0001 door control.rl TFK 0001 Edition Self-diagnosis for convenience system

18 01 FABIA 2000 Body Work Press key. Readout on display, e.g.: (RR door control unit) 6Q OM door control.rr TFK 0001 Press key. Ending output Vehicle system test Select function XX HELP Interrogating fault memory Connecting vehicle system tester -V.A.G and selecting the address word for the convenience system Select function 02. Confirm the entry with key Q. The number of faults stored appears on the display. Vehicle system test Select function XX Vehicle system test 02 - Interrogating fault memory X faults detected HELP Q Press key to display the stored faults consecutively. Cause and elimination: Convenience system with CAN databus cable Chap Convenience system with LIN databus cable Chap Note If a fault is detected: 1. Remove fault. 2. Erase fault memory (Function 05). 3. Perform a functional test of the convenience system. 4. Interrogate fault memory (Function 02) again. If No fault detected the program returns to its initial position after key is pressed. If anything else appears on the display: Operating instructions of the vehicle system tester. Ending output Switch off ignition and switch off vehicle system tester. No fault detected! Actuator diagnosis Connecting vehicle system tester -V.A.G and selecting the address word for the convenience system Vehicle system test Select function XX HELP Self-diagnosis for convenience system Edition 01.05

19 01 Enter function 03. Confirm the entry with key Q. Vehicle system test 03 Actuator diagnosis Q Door handle switches are lit. 1) Press key. Warning lamp in door trim panel flashes. Press key. Exit warning light lights up. Press key. Sliding roof closes. 2) Press key. Turn signals on. 3) Press key. Alarm horn activated. 3) Press key. Actuator diagnosis Inside door handle lighting Actuator diagnosis CL warning lamp Safe Actuator diagnosis Exit warning light Actuator diagnosis Close sliding roof signal Actuator diagnosis Turn signal control Actuator diagnosis Alarm horn - H12 Actuator diagnosis END Press key. Ending output Function unknown or cannot be carried out at the moment Erasing fault memory Conditions: Fault memory was interrogated. Fault was eliminated. Functional test was performed. Connecting vehicle system tester -V.A.G and selecting the address word for the convenience system Enter function 05. Vehicle system test Select function XX HELP 1) Not fitted on FABIA. 2) Only on vehicles equipped with sliding roof. 3) Only on vehicles with remote control or alarm function. Edition Self-diagnosis for convenience system

20 01 Confirm the entry with key Q. Vehicle system test 05 Erase fault memory FABIA 2000 Body Work Q Press key. Vehicle system test The fault memory is erased Note If the following message is displayed the test sequence is incorrect: Carefully follow the test sequence step by step: First interrogate the fault memory and then erase. Caution! Fault memory was not interrogated Ending output Enter function 06. Confirm the entry with key Q. Switch off ignition. Disconnect vehicle system tester -V.A.G from the connector. Coding control unit Vehicle system test Select function XX Vehicle system test 06 End output Q Connecting vehicle system tester -V.A.G and selecting the address word for the convenience system Enter function 07. Confirm the entry with key Q. Enter code number following table: Vehicle system test Select function XX Vehicle system test 07 Coding control unit HELP Coding control unit Enter code number XXXXX ( ) Q Table of codes for vehicles with CAN databus cable Vehicle equipment Code number individual door opening Code number overall door opening Central locking without power-window lifter Central locking with 2 power-window lifters Central locking with 4 power-window lifters Self-diagnosis for convenience system Edition 01.05

21 01 Table of codes for vehicles with LIN databus cable Vehicle equipment Code number individual door opening Code number overall door opening Central locking without power-window lifter Confirm the entry with key Q. The control unit identification number, the control unit code number and the workshop code are displayed. If the control unit rejects an entered code number the following message will be displayed: 6Q OM convenience unit Coding WSC xxxxx Fault Coding XXXXX not accepted In this case the control unit was not coded with the data required for the vehicle. Check whether the right control unit was fitted on the vehicle (compare part number and character index), or whether possibly a wrong code was entered. Repeat coding. If the control unit cannot be coded (correct control unit, correct code number) the control unit is defective. End funtion: Press key. Enter function 06. Confirm the entry with key Q. Vehicle system test Select function XX Vehicle system test 06 End output HELP Q Edition Self-diagnosis for convenience system

22 01 FABIA 2000 Body Work Self-diagnosis for convenience system Edition 01.05

23 Self-diagnosis for convenience system with CAN databus cable Overview of the selectable functions of the self diagnosis for convenience system with CAN databus cable Operation Page 01 Interrogating control Chap. 01-1, unit version 02 Interrogating fault Chapter 01-1 memory 03 Actuator diagnosis Chapter Erasing fault memory Chapter Ending output Chapter Coding control unit Chap Reading measured value block 10 Adjustment Chapter 01-4 Overview of the control units for convenience system with CAN databus cable Control unit part No. 1) Central control Door control unit unit for convenience system 6Q A 01 6Q H 35 6Q C 02 6Q E 3A Program number Control unit function Control unit without power-window lifter, without radio control and without alarm function LHD Control unit without power-window lifter, with radio control without alarm function LHD 6Q C OK Control unit without power-window lifter, with radio control and alarm function (with interior monitoring) without alarm system with independent power supply LHD 6Q C 03 6Q E 2P 6Q A 04 6Q H 2Q 6Q /2Q 6Q /2Q 6Q C 06 6Q E 2S 6Q /2S 6Q /2S 6Q C 08 6Q E 2U 6Q /2U 6Q /2U Control unit without power-window lifter, with radio control and alarm function (with interior monitoring) and alarm system with independent power supply LHD 0002 TFK TFK TFK 0001 Control unit with 2 power-window lifters, without radio control and alarm function LHD Control unit with 2 power-window lifters, with radio control and without alarm function LHD Control unit with 2 power-window lifters, with radio control and alarm function (with interior monitoring) and alarm system with independent power supply LHD Edition Self-diagnosis for convenience system with CAN databus cable

24 01 FABIA 2000 Body Work Control unit part No. 1) Central control Door control unit unit for convenience system 6Q C OL 6Q E OL 6Q OL 6Q OL 6Q A 05 6Q H 2R 6Q /2R 6Q /2R 6Q Q Q C 07 6Q E 2T 6Q Q /2T 6Q /2T 6Q Q C 09 6Q E 2V 6Q /2V 6Q /2V 6Q /2V 6Q /2V 6Q C OM 6Q E OM 6Q A 0A 6Q H 2E 6Q C 0B 6Q E 2X 6Q F 2X 6Q C 0C 6Q E 2Y 6Q A 0D 6Q H 2Z 6Q C 0F 6Q E 31 6Q F 31 6Q OM 6Q OM 6Q OM 6Q OM 6Q D/2Z 6Q D/2Z 6Q F/31 6Q F/31 6Q C 0H 6Q H 33 6Q H/33 6Q H/33 6Q A 0E 6Q H 30 6Q C 0G 6Q E 32 6Q F 32 6Q E30 6Q E/30 6Q E/30 6Q E/30 6Q G/32 6Q G/32 6Q G/32 6Q G/32 Program number 0002 TFK TFK TFK TFK TFK 0001 Control unit with 2 power-window lifters, with radio control and alarm function (with interior monitoring) without alarm system with independent power supply LHD Control unit with 4 power-window lifters, without radio control and alarm function LHD Control unit with 4 power-window lifters, with radio control and without alarm function LHD Control unit with 4 power-window lifters, with radio control and alarm function (with interior monitoring) and alarm system with independent power supply LHD Control unit with 4 power-window lifters, with radio control and alarm function (with interior monitoring) without alarm system with independent power supply LHD Control unit without power-window lifter, without radio control and without alarm function RHD Control unit without power-window lifter, with radio control and without alarm function RHD Control unit without power-window lifter, with radio control and alarm function (with interior monitoring) and alarm system with independent power supply RHD 0002 TFK TFK TFK TFK TFK 0001 Control unit function Control unit with 2 power-window lifters, without radio control and alarm function RHD Control unit with 2 power-window lifters with radio control and without alarm function RHD Control unit with 2 power-window lifters, with radio control and alarm function (with interior monitoring) and alarm system with independent power supply RHD Control unit with 4 power-window lifters, without radio control and alarm function RHD Control unit with 4 power-window lifters with radio control and without alarm function RHD Self-diagnosis for convenience system with CAN databus cable Edition 01.05

25 Control unit part No. 1) Central control Door control unit unit for convenience system 6Q C 0J 6Q E 34 6Q J/34 6Q J/34 6Q J/34 6Q J/34 6Q C 0N 6Q G 3B 6Q /3B 6Q /3B 6Q /3B 6Q /3B 6Q G 36 6Q Q TFK TFK TFK Q F TFK Q F 38 6Q F 39 6Q Q Q Q Q Q Program number 0002 TFK TFK 0001 Control unit function Control unit with 4 power-window lifters, with radio control and alarm function (with interior monitoring) and alarm system with independent power supply RHD Control unit with 2 power-window lifters, without radio control and alarm function LHD Control unit with 2 power-window lifters, without radio control and alarm function RHD Control unit without power-window lifter, with 315 MHz radio control and alarm function (with interior monitoring) and alarm system with independent power supply RHD Control unit with 2 power-window lifters, with 315 MHz radio control and alarm function (with interior monitoring) and alarm system with independent power supply RHD Control unit with 4 power-window lifters, with 315 MHz radio control and alarm function (with interior monitoring) and alarm system with independent power supply RHD 01 1) Current control unit version electronic catalogue of original parts Coding control unit with CAN databus cable Connecting vehicle system tester -V.A.G and selecting function 07 code control unit. Chap Enter code number following table: Vehicle equipment Code number individual door opening Code number overall door opening Central locking without power-window lifter Central locking with 2 power-window lifters Central locking with 4 power-window lifters Edition Self-diagnosis for convenience system with CAN databus cable

26 01 FABIA 2000 Body Work Fault table Convenience system with CAN databus cable Note Below is a list of all possible faults detected by the central control unit for convenience system -J393- and displayed on -V.A.G , arranged according to their 5-digit fault code. SAE code, may be displayed on the right next to the fault number (e.g. 4214), ignore. If Info in literature appears in the display of the vehicle system tester, look for the text required in the fault table under the fault code. After repair always interrogate the fault memory using vehicle system tester -V.A.G and erase the memory. If parts are output as faulty: First check all cables and connectors to these components as well as the earth connections according to the Current Flow Diagram. Then check whether all plug connections are properly plugged into the relay plate. Replace the component only if this test does not reveal any fault. This applies in particular if faults are shown as sporadic (SP). Display on V.A.G Possible cause of fault Rectifying fault no fault detected S contact on ignition starter switch D -D Switch for FL window lifter -E Switch for FR window lifter, driver's side -E81- undefined switch status If after repair No fault detected is displayed, the self-diagnosis is completed. Terminal 15 O.K., S contact defective Cables or plug connections defective Implausible signal Cables or plug connections defective Switch for FL window lifter -E40- defective at central switch Switch for FL window lifter -E40- loose at central switch Implausible signal Cables or plug connections defective Switch for FR window lifter -E81- defective at central switch Switch for FR window lifter -E81- loose at central switch Reading measured value block Check wiring and plug connections according to the current flow diagram Check wiring and plug connections according to the current flow diagram Replace central switch for window lifter Check switch FL fastening Reading measured value block Check wiring and plug connections according to the current flow diagram Replace central switch for window lifter Check switch FR fastening Reading measured value block Self-diagnosis for convenience system with CAN databus cable Edition 01.05

27 01 Display on V.A.G Possible cause of fault Rectifying fault Switch for RL window lifter, driver's side -E Switch for RR window lifter, driver's side -E Locking unit for CL driver's side -F220- Implausible signal Cables or plug connections defective Switch for RL window lifter -E53- defective at central switch Switch for RL window lifter -E53- loose at central switch Implausible signal Cables or plug connections defective Switch for RR window lifter -E55- defective at central switch Switch for RR window lifter -E55- loose at central switch Check wiring and plug connections according to the current flow diagram Replace central switch for window lifter Check switch RL fastening Reading measured value block Check wiring and plug connections according to the current flow diagram Replace central switch for window lifter Check switch RR fastening Reading measured value block Implausible signal Locking unit defective Reading measured value block Replace locking unit Cables or plug connections defective No supply voltage for CL on driver's door Resistance in the mechanism of the locking unit and control elements Check wiring and plug connections according to the current flow diagram Check supply voltage Check mechanism and ensure smooth operation wrong equipment other locking unit type fitted 1) Replace locking unit Locking unit for CL front passenger's side -F221- Implausible signal Locking unit defective Reading measured value block Replace locking unit Cables or plug connections defective No supply voltage for CL on passenger's door Resistance in the mechanism of the locking unit and control elements Check wiring and plug connections according to the current flow diagram Check supply voltage Check mechanism and ensure smooth operation wrong equipment other locking unit type fitted 1) Replace locking unit Edition Self-diagnosis for convenience system with CAN databus cable

28 01 FABIA 2000 Body Work Display on V.A.G Possible cause of fault Rectifying fault Locking unit for RL CL -F222- Implausible signal Locking unit defective Reading measured value block Replace locking unit Cables or plug connections defective No supply voltage for CL on rear left door Resistance in the mechanism of the locking unit and control elements Check wiring and plug connections according to the current flow diagram Check supply voltage Check mechanism and ensure smooth operation wrong equipment other locking unit type fitted 1) Replace locking unit Locking unit for CL rr -F223- Implausible signal Locking unit defective Reading measured value block Replace locking unit Cables or plug connections defective No supply voltage for CL on rear right door Resistance in the mechanism of the locking unit and control elements Check wiring and plug connections according to the current flow diagram Check supply voltage Check mechanism and ensure smooth operation wrong equipment other locking unit type fitted 1) Replace locking unit Window lifter motor driver's side -V147- No setting or incorrect setting missing or incorrectly set window lifter mechanism Window lifter motor driver's side -V147- defective Initialisation for automatic lift/lower lift mechanism Replace window lifter motor driver's side -V147- Cables or plug connections defective Check wiring and plug connections according to the current flow diagram No supply voltage for CL on driver's door Check supply voltage Resistance in window lifter mechanism 2) Check mechanism and ensure smooth operation Window lifter motor passenger's side -V148- No setting or incorrect setting missing or incorrectly set window lifter mechanism Window lifter motor passenger's side -V148- defective Cables or plug connections defective Initialisation for automatic lift/lower lift mechanism Replace window lifter motor passenger's side -V148- Check wiring and plug connections according to the current flow diagram No supply voltage for CL on passenger's door Check supply voltage Resistance in window lifter mechanism 2) Check mechanism and ensure smooth operation Self-diagnosis for convenience system with CAN databus cable Edition 01.05

29 01 Display on V.A.G Possible cause of fault Rectifying fault Window lifter motor rl -V Window lifter motor RR -V Window lifter switch passenger's side -E Window lifter switch RL -E Window lifter switch RR -E54- No setting or incorrect setting No setting or incorrect setting missing or incorrectly set window lifter mechanism Window lifter motor RL -V26- defective Cables or plug connections defective No supply voltage for CL on rear left door Resistance in window lifter mechanism 2) missing or incorrectly set window lifter mechanism Window lifter motor RR -V27- defective Cables or plug connections defective No supply voltage for CL on rear right door Resistance in window lifter mechanism 2) Implausible signal Window lifter switch passenger's side -E107- defective Cables or plug connections defective Window lifter switch passenger's side -E107- loose Window lifter switch RL -E52- defective Cables or plug connections defective Window lifter switch RL -E52- loose Window lifter switch RR -E54- defective Cables or plug connections defective Window lifter switch RR -E54- loose Initialisation for automatic lift/lower lift mechanism Replace window lifter motor RL -V26- Check wiring and plug connections according to the current flow diagram Check supply voltage Check mechanism and ensure smooth operation Initialisation for automatic lift/lower lift mechanism Replace window lifter motor RR -V27- Check wiring and plug connections according to the current flow diagram Check supply voltage Check mechanism and ensure smooth operation Replace window lifter switch passenger's side -E107- Check wiring and plug connections according to the current flow diagram Check switch fastening Reading measured value block Replace window lifter motor RL -E52- Check wiring and plug connections according to the current flow diagram Check switch fastening Reading measured value block Replace window lifter switch RR -E54- Check wiring and plug connections according to the current flow diagram Check switch fastening Reading measured value block Edition Self-diagnosis for convenience system with CAN databus cable

30 01 FABIA 2000 Body Work Display on V.A.G Possible cause of fault Rectifying fault Replace mirror adjustment motor driver's side -V Mirror adjustment motor passenger's side -V Close sliding roof signal Motor for CL tailgate -V53-, LOCK Motor for CL tailgate -V53-, UNLOCK Key Key Key 3 Short circuit to positive undefined switch status undefined switch status Adaptation threshold (mul) exceeded Adaptation threshold (mul) exceeded Adaptation threshold (mul) exceeded Replace mirror adjustment motor driver's side -V149- defective Cables or plug connections defective No supply voltage on driver's door Replace mirror adjustment motor passenger's side -V150- defective Cables or plug connections defective No supply voltage on passenger's door Cables or plug connections defective Sliding roof switch defective Sliding roof motor defective Replace mirror adjustment motor Replace driver's side -V149- Check wiring and plug connections according to the current flow diagram Check supply voltage Replace mirror adjustment motor passenger's side -V150- Check wiring and plug connections according to the current flow diagram Check supply voltage Check wiring and plug connections according to the current flow diagram Replace sliding roof switch Replace sliding roof motor Motor for CL tailgate defective Replace motor for CL tailgate Cables or plug connections defective Resistance in lock control mechanism Check wiring and plug connections according to the current flow diagram Check lock control mechanism and ensure smooth operation Motor for CL tailgate defective Replace motor for CL tailgate Cables or plug connections defective Resistance in lock control mechanism Check wiring and plug connections according to the current flow diagram Check lock control mechanism and ensure smooth operation Key not adapted Reading measured value block Key was operated over 200 times outside the reception range Perform adaptation Chap Key not adapted Reading measured value block Key was operated over 200 times outside the reception range Perform adaptation Chap Key not adapted Reading measured value block Key was operated over 200 times outside the reception range Perform adaptation Chap Self-diagnosis for convenience system with CAN databus cable Edition 01.05

31 01 Display on V.A.G Possible cause of fault Rectifying fault Key Lock the CL key switch on the driver's side Adaptation threshold (mul) exceeded Short circuit to earth Key not adapted Reading measured value block Key was operated over 200 times outside the reception range Cables or plug connections defective Perform adaptation Chap Reading measured value block Lock cylinder defective Replace lock cylinder Lock cylinder loose Check lock cylinder installation Unlock the CL key switch on the driver's side Lock the CL key switch on the passenger's side Unlock the CL key switch on the passenger's side Window lifter: Activation of thermo fuse, driver's side Window lifter: Activation of thermo fuse, front passenger's side Window lifter: Activation of thermo fuse, RL Short circuit to earth Short circuit to earth Short circuit to earth Cables or plug connections defective Reading measured value block Lock cylinder defective Replace lock cylinder Lock cylinder loose Check lock cylinder installation Cables or plug connections defective Reading measured value block Lock cylinder defective Replace lock cylinder Lock cylinder loose Check lock cylinder installation Cables or plug connections defective Reading measured value block Lock cylinder defective Replace lock cylinder Lock cylinder loose Check lock cylinder installation Cables or plug connections defective Window lifter mechanism loose or stiff Reading measured value block Check window lifter mechanism Resistance in window lifter motor Check window lifter motor Resistance in the window run during lifting and lowering of door window Eliminate obstacle Cables or plug connections defective Window lifter mechanism loose or stiff Reading measured value block Check window lifter mechanism Resistance in window lifter motor Check window lifter motor Resistance in the window run during lifting and lowering of door window Eliminate obstacle Cables or plug connections defective Window lifter mechanism loose or stiff Reading measured value block Check window lifter mechanism Resistance in window lifter motor Check window lifter motor Resistance in the window run during lifting and lowering of door window Eliminate obstacle Edition Self-diagnosis for convenience system with CAN databus cable

32 01 FABIA 2000 Body Work Display on V.A.G Possible cause of fault Rectifying fault Window lifter: Activation of thermo fuse, RR Cables or plug connections defective Window lifter mechanism loose or stiff Reading measured value block Check window lifter mechanism Resistance in window lifter motor Check window lifter motor Central lokking thermo fuse Control unit wrongly coded Alarm horn -H12- undefined switch status Resistance in the window run during lifting and lowering of door window Cables or plug connections defective Eliminate obstacle Reading measured value block Resistance in door lock Check door lock another control unit used Replace control unit Control unit wrongly coded Check control unit coding Cables or plug connections defective Check wiring and plug connections according to the current flow diagram defective Alarm horn defective Replace alarm horn Sensors for interior monitoring Key programming, wrong Databus drive Control unit for multi-function unit No communication Cables or plug connections defective internal power supply Alarm system with independent supply defective Open circuit Cables or plug connections defective defective Sensors for interior monitoring defective please read out fault memory Sensors for interior monitoring not fitted The key adaptation was not carried out correctly No communication between units No speed signal or Gateway No communication No communication between units please read out fault memory Check wiring and plug connections according to the current flow diagram Check alarm system with independent supply, if necessary replace Check wiring and plug connections according to the current flow diagram Replace sensors for interior monitoring Check the connection of sensors Adapt key again Chap Reading measured value block Read fault memory of the central control unit Electrical System Rep.-Gr. 90 Read fault memory of the central control unit Electrical System Rep.-Gr Self-diagnosis for convenience system with CAN databus cable Edition 01.05